KSZ9692-MII-PTP-EV

KSZ9692PB User Guide Brief KSZ9692PB Evaluation Platform Rev 2.0 General Description Features The KSZ9692PB Evaluation Platform accelerates product time-to-market by providing a hardware platform for proof-of-concept, software development, and product demonstration. • • • • • • • • • • • • • • • KSZ9692PB as System-on-Chip (SoC) 64MB of embedded DDR memory 8MB of embedded NOR Flash Memory Place-Holder for embedded NAND Flash Memory WAN 10/100/1000 Ethernet Port LAN 10/100/1000 Ethernet Port One standard PCI interface edge connector One Mini-PCI interface Type III connector Two standard USB 2.0 interface connectors SD/SDIO interface connector One UART DB-9 Connector Onboard jumper header for I2S interface Onboard jumper header for SPI/I2C interface Onboard jumper header for four GPIO interface Two GPIO controlled LEDs for S/W assist debug/development • JTAG port for S/W development Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com July 2009 M9999-100407-1.0 Micrel, Inc. KSZ9692PB Evaluation Platform User Guide Brief Block Diagram 5V input Ethernet RJ-45 On-Board Power +3.3V +2.6V +1.3V MiniPCI PCI RESET WAN Port 10/100/1000 Ethernet RJ-45 Debug LEDs LAN Port 10/100/1000 I2S KSZ9692PB SoC USB 2.0 host 1 SPI/I2C SPI/I2C USB 2.0 host 2/ Device JTAG Port SPI/I2C SD/SDIO UART DDR Bus DDR memory Static Memory Bus NOR Flash NAND Flash KSZ9692PB Evaluation Platform Block Diagram July 2009 2 M9999-100407-1.0 Micrel, Inc. KSZ9692PB Evaluation Platform User Guide Brief Revision History Revision Date Summary of Changes 2.0 7/28/09 Initial Release July 2009 3 M9999-100407-1.0 Micrel, Inc. KSZ9692PB Evaluation Platform User Guide Brief Content General Description .................................................................................................................................................1 Block Diagram ..........................................................................................................................................................2 Revision History .......................................................................................................................................................3 Evaluation Board Description.................................................................................................................................5 Chip Select Assignments .......................................................................................................................................5 DDR Memory .........................................................................................................................................................5 NOR Flash Memory ...............................................................................................................................................5 NAND Flash Memory .............................................................................................................................................5 PCI Interface ..........................................................................................................................................................5 WAN Interface........................................................................................................................................................5 LAN Interface .........................................................................................................................................................6 USB Interfaces.......................................................................................................................................................6 SD/SDIO Interface .................................................................................................................................................6 I2S Interface...........................................................................................................................................................6 SPI/I2C Interface....................................................................................................................................................6 GPIO Interface .......................................................................................................................................................6 UART .....................................................................................................................................................................7 Multi-ICE/JTAG Connector ....................................................................................................................................7 LEDs ......................................................................................................................................................................7 Reset......................................................................................................................................................................7 Power and Ground.................................................................................................................................................7 July 2009 4 M9999-100407-1.0 Micrel, Inc. KSZ9692PB Evaluation Platform User Guide Brief Evaluation Board Description This User Guide Brief is a summary of the features and interfaces supported by KSZ9692PB evaluation board Rev 2.0. Chip Select Assignments KSZ9692 Chip Select Signal KSZ9692 Pin # CSN0 Device U14 DDR Bank RCSN0 L1 NOR FLASH Bank 0 RCSN1 K3 NOR FLASH Bank 1 (Not assigned) NCEN0 V3 NAND FLASH Bank 0 NCEN1 T3 NAND FLASH Bank 1 (Not assigned) ECSN0 M2 External I/O Bank 0 (Not assigned) ECSN1 N1 External I/O Bank 1 (Not assigned) ECSN2 L3 External I/O Bank 2 (Not assigned) Table 1. Chip Select Assignments DDR Memory The evaluation board provides 64MB of DDR memory with a single Micron MT46V32M16-5B device (location U14) in a 32Mx16 bit configuration. This is DDR bank normal configuration. Note: a second Micron MT46V32M16-5B device resides in location U15 for 32Mx32 configuration. This is for engineering test only. DDR 32-bit data width is not supported for normal operation. NOR Flash Memory The evaluation board provides 8MB of NOR flash memory. The part number is Spansion S29GL064N90. This device is a 4Mx16 bit configuration and mounted directly onto board at U4 location. The evaluation board is configured to boot from NOR flash. NAND Flash Memory The evaluation board provides a place holder for NAND flash memory at location U11. The user can solder NAND flash of their choice at this location. PCI Interface The evaluation board provides one standard PCI edge connector and one mini-PCI type III connector to allow for applications using existing PCI based peripherals. The PCI interface supports 33/66MHz and is compliant with PCI Local Bus Specification 2.3. The voltages supplied to the connectors are 3.3V and 5.0V. ± 12V supply is not available. WAN Interface The WAN MAC of KSZ9692PB is interfaced to Micrel KSZ9021RL PHY via RGMII bus. RJ-45 connector at location RJ2 provides network connectivity at 10/100/1000 BASE-TX. There are two onboard LEDs associated with WAN port as following: LED Location Designation Description D13 LINK Link partner establishment D12 ACTIVITY Network traffic activity Table 2. WAN Port LED Description July 2009 5 M9999-100407-1.0 Micrel, Inc. KSZ9692PB Evaluation Platform User Guide Brief LAN Interface The LAN MAC of KSZ9692PB is interfaced to Micrel KSZ9021RL PHY via RGMII bus . RJ-45 connector at location RJ1 provides network connectivity at 10/100/1000 BASE-TX. There are two onboard LEDs associated with LAN port as following: LED Location Designation Description D11 LINK Link partner establishment D10 ACTIVITY Network traffic activity Table 3. LAN Port LED Description USB Interfaces The evaluation board provides two standard USB 2.0 host ports to allow connectivity to USB based peripherals. Each port is individually associated with 5V supply peripheral power switch (Micrel MIC2015) to power-up external peripherals. Port1 and port2 are located at JP7 and JP5 connectors respectively. Port2 is configurable as device. To configure Port2 as device, R41 must be installed with a 0 ohm value resistor. Port2 as device is self-powered and does not need external power. Therefore external 5V power to Port2 connector must not be applied. SD/SDIO Interface The evaluation board provides a standard SD/SDIO host port to allow connectivity to SD/SDIO based peripherals. The SD/SDIO port is located at JP4. I2S Interface The evaluation board provides I2S interface at JP3 header to allow connectivity to I2S based peripherals such as an audio CODEC. The following table is map of I2S signals: KSZ8692PB I2S Signal JP3 Pin Assignment SDI 1 SDO 2 LRCLK 3 BCLK 4 MCLK 5 GND 6 Table 4. I2S Interface Description SPI/I2C Interface The evaluation board provides SPI and I2C interface bus at JP1 header to allow connectivity to SPI or I2C-based peripherals. The following table is map of SPI/I2C signals: KSZ8692PB SPI/I2C Signal JP1 Pin Assignment CS 1 RDY 2 MISO 3 MOSI/SDA 4 CK/SCL 5 GND 6 Table 5. SPI/I2C Interface Description GPIO Interface The evaluation board provides direct access to KSZ9692PB GPIO[7:4] pins at JP6. The following table is map of July 2009 6 M9999-100407-1.0 Micrel, Inc. KSZ9692PB Evaluation Platform User Guide Brief GPIO pins: KSZ8692PB SPI/I2C Signal JP6 Pin Assignment GPIO4 1 GPIO5 2 GPIO6 3 GPIO7 4 NC 5 GND 6 Table 6. GPIO[7:4] Interface Description UART The evaluation board provides a high speed UART interface. The UART port1 implements Maxim MAX3243 as RS232 transceiver and supports up to 120kbps. The UART interface is a male DB9, null-modem connector for use as a console port. This port also supports modem control signals. Connector Pin No. KSZ9692 Signal Name 1 UDCDN 2 3 4 KSZ9692PB I/O KSZ9692PB Signal Description I UART Data Carrier Detect URXD I UART Receive Data UTXD O UART Transmit Data UDTRN O Data Terminal Ready (active low) 5 N/A 6 UDSRN N/A I Ground UART Data Set Ready 7 URTSN O UART Request To Send 8 UCTSN I Clear To Send 9 URIN I Ring Indicator Table 7. UART Interface Description Multi-ICE/JTAG Connector The KSZ9692PB JTAG interface located at JP8 header is a standard 20-pin connector for the Multi-ICE. This connector can be used to download code to flash and for software development and debugging purposes. LEDs The evaluation board provides two user LEDs to assist with software debug and development. These LED indicators are controlled by KSZ9692PB GPIO[9:8] pins. A logic low of an individual GPIO turns the associated LED ON and logic high turns it OFF. The following table is map of GPIO versus LED: LED Location GPIO Assignment D9 GPIO8 D8 GPIO9 Table 8. User LED Description Reset The evaluation board implements reset at location S1 push-button. By pressing this push-button momentarily, the board experiences hard reset. Power and Ground Power to the evaluation board is supplied through a 5.0V DC power jack at J2 connector. The 5.0V DC power is then July 2009 7 M9999-100407-1.0 Micrel, Inc. KSZ9692PB Evaluation Platform User Guide Brief converted down to the three voltage levels (1.3V, 3.3V, 2.6V) required by KSZ9692PB. The following table outlines onboard derived voltages and test points: Voltages Micrel Part Test Points V1.3 (Digital & Analog Core) MIC4724 TP2 V3.3 (Digital & Analog Core) MIC2193 TP1, TP5 V2.6 (Digital DDR memory) MIC49300 (see Note 1) TP7 TP3, TP4, TP9, TP10, TP11, TP12 GND Table 9. Voltages and Test Points The evaluation board features a power LED indicator at location D4 (next to power jack) so that the user may easily determine if the board is powered. The evaluation board power consumption is typically 5V @ 1.4A with both WAN and LAN ports linked at 1000 Mbps to their respective link partners. It is recommended to use a DC power supply rated for 5VDC @ 4A. Care must be taken to insure this supply is well regulated and noise free. Note 1: DDR device Micron MT46V32M16-5B requires 2.6V supply (See Micron Electrical Specification). MIC49300 is adjusted from 2.5V to 2.6V to meet this requirement. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. M9999-100407-1.0 July 2009 Micrel Products are not designed or authorized for use as components in8life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2008 Micrel, Inc.