MCP14A1201/2
12.0A MOSFET Driver with Low Threshold Input and Enable
Features
General Description
• High Peak Output Current: 12.0A (typical)
• Wide Input Supply Voltage Operating Range:
- 4.5V to 18V
• Low Shoot-Through/Cross-Conduction Current in
Output Stage
• High Capacitive Load Drive Capability:
- 15,000 pF in 25 ns (typical)
• Short Delay Times: 28 ns (tD1), 28 ns (tD2) (typical)
• Low Supply Current: 360 µA (typical)
• Low-Voltage Threshold Input and Enable with
Hysteresis
• Latch-Up Protected: Withstands 500 mA Reverse
Current
• Space-Saving Packages:
- 8-Lead MSOP
- 8-Lead SOIC
- 8-Lead 2 x 3 TDFN
The MCP14A1201/2 devices are high-speed MOSFET
drivers that are capable of providing up to 12.0A of
peak current while operating from a single 4.5V to 18V
supply. There are two output configurations available;
inverting
(MCP14A1201)
and
noninverting
(MCP14A1202). These devices feature low shootthrough current, fast rise and fall times, and matched
propagation delays which make them ideal for high
switching frequency applications.
Applications
•
•
•
•
•
Switch Mode Power Supplies
Pulse Transformer Drive
Line Drivers
Level Translator
Motor and Solenoid Drive
The MCP14A1201/2 family of devices offers enhanced
control with Enable functionality. The active-high
Enable pin can be driven low to drive the output of the
MCP14A1201/2 low, regardless of the status of the
Input pin. An integrated pull-up resistor allows the user
to leave the Enable pin floating for standard operation.
These devices are highly latch-up resistant under any
condition within their power and voltage ratings. They
can accept up to 500 mA of reverse current being
forced back into their outputs without damage or logic
upset. All terminals are fully protected against
electrostatic discharge (ESD) up to 2 kV (HBM) and
200V (MM).
Package Types
MCP14A1201/MCP14A1202
MSOP/SOIC
8 VDD
VDD 1
IN 2
7 OUT/OUT
EN 3
GND 4
6 OUT/OUT
5 GND
MCP14A1201/MCP14A1202
2 x 3 TDFN*
VDD 1
IN 2
EN 3
GND 4
8 VDD
EP
9
7 OUT/OUT
6 OUT/OUT
5 GND
* Includes Exposed Thermal Pad (EP); see Table 3-1.
2019 Microchip Technology Inc.
DS20006228A-page 1
MCP14A1201/2
Functional Block Diagram
VDD
Internal
Pull-Up
Enable
VREF
GND
Inverting
Output-Pin 7
Output – Pin 6
VDD
Input
VREF
GND
DS20006228A-page 2
Non-Inverting
MCP14A1201 Inverting
MCP14A1202 NonLnverting
2019 Microchip Technology Inc.
MCP14A1201/2
1.0
ELECTRICAL
CHARACTERISTICS
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of
the device at those or any other conditions above those
indicated in the operational sections of this
specification is not intended. Exposure to maximum
rating conditions for extended periods may affect
device reliability.
Absolute Maximum Ratings †
VDD, Supply Voltage............................................. +20V
VIN, Input Voltage........... (VDD + 0.3V) to (GND - 0.3V)
VEN, Enable Voltage....... (VDD + 0.3V) to (GND - 0.3V)
Package Power Dissipation (TA = +50°C)
8L MSOP ..................................................... 0.63 W
8L SOIC ....................................................... 1.00 W
8L 2 x 3 TDFN.............................................. 1.86 W
ESD Protection on all pins .........................2 kV (HBM)
....................................................................200V (MM)
DC CHARACTERISTICS
Electrical Specifications: Unless otherwise noted, TA = +25°C, with 4.5V VDD 18V.
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Input Voltage Range
VIN
GND - 0.3V
—
VDD + 0.3
V
Logic ‘1’ High Input Voltage
VIH
2.0
1.6
—
V
Logic ‘0’ Low Input Voltage
VIL
—
1.3
0.8
V
VHYST(IN)
—
0.3
—
V
IIN
-1
—
+1
µA
Enable Voltage Range
VEN
GND - 0.3V
—
VDD + 0.3
V
Logic ‘1’ High Enable Voltage
VEH
2.0
1.6
—
V
Logic ‘0’ Low Enable Voltage
VEL
—
1.3
0.8
V
VHYST(EN)
—
0.3
—
V
RENBL
—
1.8
—
MΩ
VDD = 18V, ENB = GND
Enable Input Current
IEN
—
10
—
µA
VDD = 18V, ENB = GND
Propagation Delay
tD3
—
28
33
ns
VDD = 18V, VEN = 5V,
see Figure 4-3, (Note 1)
Propagation Delay
tD4
—
28
33
ns
VDD = 18V, VEN = 5V,
see Figure 4-3, (Note 1)
VOH
VDD - 0.025
—
—
V
IOUT = 0A
Low Output Voltage
VOL
—
—
0.025
V
IOUT = 0A
Output Resistance, High
ROH
—
0.9
1.5
Ω
IOUT = 10 mA, VDD = 18V
Output Resistance, Low
ROL
—
0.6
1.2
Ω
IOUT = 10 mA, VDD = 18V
Peak Output Current
IPK
—
12.0
—
A
VDD = 18V (Note 1)
Latch-Up Protection Withstand
Reverse Current
IREV
0.5
—
—
A
Duty cycle 2%, t 300 µs
(Note 1)
Rise Time
tR
—
25
30
ns
VDD = 18V, CL = 15,000 pF,
see Figure 4-1, Figure 4-2
Fall Time
tF
—
25
30
ns
VDD = 18V, CL = 15,000 pF,
see Figure 4-1, Figure 4-2
Note 1:
Tested during characterization, not production tested.
Input
Input Voltage Hysteresis
Input Current
0V VIN VDD
Enable
Enable Voltage Hysteresis
Enable Pin Pull-Up Resistance
Output
High Output Voltage
Switching Time (Note 1)
2019 Microchip Technology Inc.
DS20006228A-page 3
MCP14A1201/2
DC CHARACTERISTICS (CONTINUED)
Electrical Specifications: Unless otherwise noted, TA = +25°C, with 4.5V VDD 18V.
Parameters
Delay Time
Sym.
Min.
Typ.
Max.
Units
Conditions
tD1
—
28
33
ns
VDD = 18V, VIN = 5V, see
Figure 4-1 and Figure 4-2
tD2
—
28
33
ns
VDD = 18V, VIN = 5V, see
Figure 4-1 and Figure 4-2
VDD
4.5
—
18
V
IDD
—
360
600
µA
VIN = 3V, VEN = 3V
IDD
—
360
600
µA
VIN = 0V, VEN = 3V
IDD
—
360
600
µA
VIN = 3V, VEN = 0V
IDD
—
360
600
µA
VIN = 0V, VEN = 0V
Power Supply
Supply Voltage
Power Supply Current
Note 1:
Tested during characterization, not production tested.
DC CHARACTERISTICS (OVER OPERATING TEMPERATURE RANGE)
Electrical Specifications: Unless otherwise indicated, over the operating range with 4.5V VDD 18V.
Parameters
Sym.
Min.
Typ.
Max.
VIN
Logic ‘1’ High Input Voltage
Logic ‘0’ Low Input Voltage
Units
GND - 0.3V
—
VDD + 0.3
V
VIH
2.0
1.6
—
V
VIL
—
1.3
0.8
V
VHYST(IN)
—
0.3
—
V
IIN
-10
—
+10
µA
VEN
GND - 0.3V
—
VDD + 0.3
V
Logic ‘1’ High Enable Voltage
VEH
2.0
1.6
—
V
Logic ‘0’ Low Enable Voltage
VEL
—
1.3
0.8
V
Conditions
Input
Input Voltage Range
Input Voltage Hysteresis
Input Current
0V VIN VDD
Enable
Enable Voltage Range
Enable Voltage Hysteresis
VHYST(EN)
—
0.3
—
V
Enable Input Current
IEN
—
12
—
µA
VDD = 18V, ENB = GND
Propagation Delay
tD3
—
32
37
ns
VDD = 18V, VEN = 5V, TA = +125°C,
see Figure 4-3, (Note 1)
Propagation Delay
tD4
—
32
37
ns
VDD = 18V, VEN = 5V, TA = +125°C,
see Figure 4-3, (Note 1)
High Output Voltage
VOH
VDD - 0.025
—
—
V
DC Test
Low Output Voltage
VOL
—
—
0.025
V
DC Test
Output Resistance, High
ROH
—
—
2
Ω
IOUT = 10 mA, VDD = 18V
Output Resistance, Low
ROL
—
—
1.7
Ω
IOUT = 10 mA, VDD = 18V
Output
Note 1:
Tested during characterization, not production tested.
DS20006228A-page 4
2019 Microchip Technology Inc.
MCP14A1201/2
DC CHARACTERISTICS (OVER OPERATING TEMPERATURE RANGE) (CONTINUED)
Electrical Specifications: Unless otherwise indicated, over the operating range with 4.5V VDD 18V.
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Rise Time
tR
—
30
35
ns
VDD = 18V, CL = 15,000 pF,
TA = +125°C, see Figure 4-1,
Figure 4-2
Fall Time
tF
—
30
35
ns
VDD = 18V, CL = 15,000 pF,
TA = +125°C, see Figure 4-1,
Figure 4-2
Delay Time
tD1
—
32
37
ns
VDD = 18V, VIN = 5V, TA = +125°C,
see Figure 4-1, Figure 4-2
tD2
—
32
37
ns
VDD = 18V, VIN = 5V, TA = +125°C,
see Figure 4-1, Figure 4-2
VDD
4.5
—
18
V
Switching Time (Note 1)
Power Supply
Supply Voltage
Power Supply Current
Note 1:
IDD
—
—
750
uA
VIN = 3V, VEN = 3V
IDD
—
—
750
uA
VIN = 0V, VEN = 3V
IDD
—
—
750
uA
VIN = 3V, VEN = 0V
IDD
—
—
750
uA
VIN = 0V, VEN = 0V
Tested during characterization, not production tested.
TEMPERATURE CHARACTERISTICS
Electrical Specifications: Unless otherwise noted, all parameters apply with 4.5V VDD 18V
Parameter
Sym.
Min.
Typ.
Max.
Units
TA
-40
—
+125
°C
Comments
Temperature Ranges
Specified Temperature Range
Maximum Junction Temperature
TJ
—
—
+150
°C
Storage Temperature Range
TA
-65
—
+150
°C
Junction-to-Ambient Thermal Resistance, 8LD MSOP
JA
—
158
—
°C/W
Note 1
Junction-to-Ambient Thermal Resistance, 8LD SOIC
JA
—
99.8
—
°C/W
Note 1
Junction-to-Ambient Thermal Resistance, 8LD TDFN
JA
—
53.7
—
°C/W
Note 1
Junction-to-Top Characterization Parameter, 8LD MSOP
JT
—
2.4
—
°C/W
Note 1
Junction-to-Top Characterization Parameter, 8LD SOIC
JT
—
5.9
—
°C/W
Note 1
Junction-to-Top Characterization Parameter, 8LD TDFN
JT
—
0.5
—
°C/W
Note 1
Junction-to-Board Characterization Parameter, 8LD MSOP
JB
—
115.2
—
°C/W
Note 1
Junction-to-Board Characterization Parameter, 8LD SOIC
JB
—
64.8
—
°C/W
Note 1
Junction-to-Board Characterization Parameter, 8LD TDFN
JB
—
24.4
—
°C/W
Note 1
Package Thermal Resistances
Note 1:
Parameter is determined using High K 2S2P 4-Layer board as described in JESD 51-7, as well as JESD
51-5 for packages with exposed pads.
2019 Microchip Technology Inc.
DS20006228A-page 5
MCP14A1201/2
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, TA = +25°C with 4.5V VDD 18V.
)DOO7LPHQV
5LVH7LPHQV
S)
S)
S)
S)
S)
S)
9
9
9
6XSSO\9ROWDJH9
FIGURE 2-1:
Voltage.
&DSDFLWLYH/RDGS)
Rise Time vs. Supply
FIGURE 2-4:
Load.
5LVHDQG)DOO7LPHQV
5LVH7LPHQV
9
9
9
Fall Time vs. Capacitive
9'' 9
W5S)
W)S)
W5S)
W)S)
&DSDFLWLYH/RDGS)
FIGURE 2-2:
Load.
7HPSHUDWXUH&
Rise Time vs. Capacitive
&URVVRYHU&XUUHQW$
FIGURE 2-5:
Temperature.
Rise and Fall Time vs.
S)
S)
S)
S)
S)
S)
)DOO7LPHQV
0+]
N+]
N+]
N+]
N+]
FIGURE 2-3:
Voltage.
DS20006228A-page 6
Fall Time vs. Supply
6XSSO\9ROWDJH9
6XSSO\9ROWDJH9
FIGURE 2-6:
Supply Voltage.
Crossover Current vs.
2019 Microchip Technology Inc.
MCP14A1201/2
Note: Unless otherwise indicated, TA = +25°C with 4.5V VDD 18V.
(QDEOH3URSDJDWLRQ'HOD\QV
,QSXW3URSDJDWLRQ'HOD\QV
9,1 9
W'
W'
9(1 9
W'
W'
6XSSO\9ROWDJH9
Input Propagation Delay vs.
9'' 9
W'
W'
9'' 9
9,1 9
W'
W'
W'
Input Propagation Delay vs.
2019 Microchip Technology Inc.
(QDEOH9ROWDJH$PSOLWXGH9
FIGURE 2-11:
Enable Propagation Delay
Time vs. Enable Voltage Amplitude.
9'' 9
9(1 9
W'
W'
7HPSHUDWXUH&
FIGURE 2-9:
Temperature.
W'
(QDEOH3URSDJDWLRQ'HOD\QV
,QSXW3URSDJDWLRQ'HOD\QV
9'' 9
FIGURE 2-8:
Input Propagation Delay
Time vs. Input Amplitude.
,QSXW9ROWDJH$PSOLWXGH9
FIGURE 2-10:
Enable Propagation Delay
vs. Supply Voltage.
(QDEOH3URSDJDWLRQ'HOD\QV
,QSXW3URSDJDWLRQ'HOD\QV
FIGURE 2-7:
Supply Voltage.
6XSSO\9ROWDJH9
7HPSHUDWXUH&
FIGURE 2-12:
vs. Temperature.
Enable Propagation Delay
DS20006228A-page 7
MCP14A1201/2
Note: Unless otherwise indicated, TA = +25°C with 4.5V VDD 18V.
,QSXW7KUHVKROG9
4XLHVFHQW&XUUHQW$
9,+
9,/
6XSSO\9ROWDJH9
FIGURE 2-13:
Quiescent Supply Current
vs. Supply Voltage.
FIGURE 2-16:
Voltage.
(QDEOH7KUHVKROG9
4XLHVFHQW&XUUHQW$
FIGURE 2-14:
vs. Temperature.
9'' 9
9(+
9(/
7HPSHUDWXUH&
Quiescent Supply Current
FIGURE 2-17:
Temperature.
Enable Threshold vs.
9'' 9
9,+
(QDEOH7KUHVKROG9
,QSXW7KUHVKROG9
Input Threshold vs. Supply
7HPSHUDWXUH&
9'' 9
6XSSO\9ROWDJH9
9,/
9(+
9(/
FIGURE 2-15:
Temperature.
DS20006228A-page 8
7HPSHUDWXUH&
Input Threshold vs.
6XSSO\9ROWDJH9
FIGURE 2-18:
Supply Voltage.
Enable Threshold vs.
2019 Microchip Technology Inc.
MCP14A1201/2
9,1 90&3$
9,1 90&3$
6XSSO\&XUUHQWP$
52+ 2XWSXW5HVLVWDQFH
Note: Unless otherwise indicated, TA = +25°C with 4.5V VDD 18V.
7$ &
7$ &
9'' 9
0+]
N+]
N+]
N+]
N+]
N+]
6XSSO\9ROWDJH9
FIGURE 2-19:
Output Resistance (Output
High) vs. Supply Voltage.
FIGURE 2-22:
Supply Current vs.
Capacitive Load (VDD = 12V).
9,1 90&3$
9,1 90&3$
6XSSO\&XUUHQWP$
52/ 2XWSXW5HVLVWDQFH
7$ &
7$ &
9'' 9
0+]
N+]
N+]
N+]
N+]
N+]
FIGURE 2-23:
Supply Current vs.
Capacitive Load (VDD = 6V).
9'' 9
6XSSO\&XUUHQWP$
6XSSO\&XUUHQWP$
FIGURE 2-20:
Output Resistance (Output
Low) vs. Supply Voltage.
0+]
N+]
N+]
N+]
N+]
N+]
&DSDFLWLYH/RDGS)
FIGURE 2-21:
Supply Current vs.
Capacitive Load (VDD = 18V).
2019 Microchip Technology Inc.
&DSDFLWLYH/RDGS)
6XSSO\9ROWDJH9
&DSDFLWLYH/RDGS)
9'' 9
S)
S)
S)
S)
S)
S)
6ZLWFKLQJ)UHTXHQF\N+]
FIGURE 2-24:
Supply Current vs.
Frequency (VDD = 18V).
DS20006228A-page 9
MCP14A1201/2
6XSSO\&XUUHQWP$
Note: Unless otherwise indicated, TA = +25°C with 4.5V VDD 18V.
9'' 9
S)
S)
S)
S)
S)
S)
6ZLWFKLQJ)UHTXHQF\N+]
FIGURE 2-25:
Supply Current vs.
Frequency (VDD = 12V).
6XSSO\&XUUHQWP$
9'' 9
S)
S)
S)
S)
S)
S)
6ZLWFKLQJ)UHTXHQF\N+]
FIGURE 2-26:
Supply Current vs.
Frequency (VDD = 6V).
(QDEOH&XUUHQW$
6XSSO\9ROWDJH9
FIGURE 2-27:
Voltage.
DS20006228A-page 10
Enable Current vs. Supply
2019 Microchip Technology Inc.
MCP14A1201/2
3.0
12.0A PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
MCP14A1201/2
3.1
8L 2 x 3 TDFN
8L MSOP/SOIC
1
1
2
3
Symbol
Description
VDD
Supply Input
2
IN
Control Input
3
EN
Device Enable
4
4
GND
Power Ground
5
5
GND
Power Ground
6
6
OUT/OUT
Push-Pull Output
7
7
OUT/OUT
Push-Pull Output
8
8
VDD
Supply Input
EP
—
EP
Exposed Thermal Pad (GND)
Supply Input Pin (VDD)
3.4
Power Ground Pin (GND)
VDD is the bias supply input for the MOSFET driver and
has a voltage range of 4.5V to 18V. This input must be
decoupled to ground with a local capacitor. This bypass
capacitor provides a localized low-impedance path for
the peak currents that are provided to the load.
GND is the device return pin for the input and output
stages. The GND pin should have a low-impedance
connection to the bias supply source return. When the
capacitive load is being discharged, high peak currents
will flow through the ground pin.
3.2
3.5
Control Input Pin (IN)
The MOSFET driver Control Input is a high-impedance
input featuring low threshold levels. The Input also has
hysteresis between the high and low input levels,
allowing them to be driven from slow rising and falling
signals and to provide noise immunity.
3.3
Device Enable Pin (EN)
The MOSFET driver Device Enable is a highimpedance input featuring low threshold levels. The
Enable input also has hysteresis between the high and
low input levels, allowing them to be driven from slow
rising and falling signals and to provide noise immunity.
Driving the Enable pin below the threshold will disable
the output of the device, pulling OUT/OUT low,
regardless of the status of the Input pin. Driving the
Enable pin above the threshold allows normal
operation of the OUT/OUT pin based on the status of
the Input pin. The Enable pin utilizes an internal pull up
resistor, allowing the pin to be left floating for standard
driver operation.
2019 Microchip Technology Inc.
Output Pin (OUT, OUT)
The Output is a CMOS push-pull output that is capable
of sourcing and sinking 12.0A of peak current
(VDD = 18V). The low output impedance ensures the
gate of the external MOSFET stays in the intended
state even during large transients. This output also has
a reverse current latch-up rating of 500 mA.
3.6
Exposed Metal Pad Pin (EP)
The exposed metal pad of the DFN package is
internally connected to GND. Therefore, this pad
should be connected to a Ground plane to aid in heat
removal from the package.
DS20006228A-page 11
MCP14A1201/2
4.0
APPLICATION INFORMATION
4.1
General Information
9'' 9
)
MOSFET drivers are high-speed, high-current devices
which are intended to source/sink high-peak currents to
charge/discharge the gate capacitance of external
MOSFETs or Insulated-Gate Bipolar Transistors
(IGBTs). In high frequency switching power supplies,
the Pulse-Width Modulation (PWM) controller may not
have the drive capability to directly drive the power
MOSFET. A MOSFET driver such as the
MCP14A1201/2 family can be used to provide
additional source/sink current capability.
4.2
,QSXW
)
2XWSXW
&/ S)
0&3$
9
MOSFET Driver Timing
The ability of a MOSFET driver to transition from a fullyoff state to a fully-on state is characterized by the
driver’s rise time (tR), fall time (tF) and propagation
delays (tD1 and tD2). Figure 4-1 and Figure 4-2 show
the test circuit and timing waveform used to verify the
MCP14A1201/2 timing.
,QSXW
9,+7\S
9
9,/7\S
W'
W5
W'
9
2XWSXW
9
,QSXW6LJQDOW5,6( W)$//QV
+]96TXDUH:DYH
9'' 9
)
)
,QSXW
FIGURE 4-2:
Waveform.
4.3
2XWSXW
&/ S)
0&3$
9
,QSXW
9,+7\S
9
9,/7\S
W'
W)
W'
9
W5
2XWSXW
9
,QSXW6LJQDOW5,6( W)$//чQV
+]96TXDUH:DYH
FIGURE 4-1:
Waveform.
DS20006228A-page 12
W)
Inverting Driver Timing
Noninverting Driver Timing
Enable Function
The enable pin (EN) provides additional control of the
output pin (OUT). This pin is active high and is
internally pulled up to VDD so that the pin can be left
floating to provide standard MOSFET driver operation.
When the enable pin’s input voltage is above the
enable pin high voltage threshold, (VEN_H), the output
is enabled and allowed to react to the status of the Input
pin. However, when the voltage applied to the Enable
pin falls below the low threshold voltage (VEN_L), the
driver’s output is disabled and does not respond to
changes in the status of the Input pin. When the driver
is disabled, the output is pulled down to a low state.
Refer to Table 4-1 for enable pin logic. The threshold
voltage levels for the Enable pin are similar to the
threshold voltage levels of the Input pin. Hysteresis is
provided to help increase the noise immunity of the
enable function, avoiding false triggers of the enable
signal during driver switching.
There are propagation delays associated with the
driver receiving an enable signal and the output
reacting. These propagation delays, tD3 and tD4, are
graphically represented in Figure 4-3.
2019 Microchip Technology Inc.
MCP14A1201/2
TABLE 4-1:
4.6
ENABLE PIN LOGIC
MCP14A1201
OUT
MCP14A1202
OUT
H
L
H
L
H
L
X
L
L
ENB
IN
H
H
L
Power Dissipation
The total internal power dissipation in a MOSFET driver
is the summation of three separate power dissipation
elements, as shown in Equation 4-1.
EQUATION 4-1:
P T = PL + P Q + PCC
Where:
5V
PT
=
Total power dissipation
PL
=
Load power dissipation
PQ
=
Quiescent power dissipation
PCC
=
Operating power dissipation
Enable
VEH (Typ.)
VEL (Typ.)
0V
tD3
tD4
18V
90%
4.6.1
Output
10%
0V
Ena ble Signa l: tRISE = tFALL ≤ 10 ns,
100 Hz, 0-5V Squa re Wa ve
FIGURE 4-3:
CAPACITIVE LOAD DISSIPATION
The power dissipation caused by a capacitive load is a
direct function of the frequency, total capacitive load
and supply voltage. The power lost in the MOSFET
driver for a complete charging and discharging cycle of
a MOSFET is shown in Equation 4-2.
Enable Timing Waveform.
EQUATION 4-2:
4.4
Decoupling Capacitors
Careful PCB layout and decoupling capacitors are
required when using power MOSFET drivers. Large
currents are required to charge and discharge
capacitive loads quickly. For example, approximately
720 mA are needed to charge a 1000 pF load with 18V
in 25 ns.
To operate the MOSFET driver over a wide frequency
range with low supply impedance, it is recommended to
place 1.0 µF and 0.1 µF low ESR ceramic capacitors in
parallel between the driver VDD and GND. These
capacitors should be placed close to the driver to
minimize circuit board parasitics and provide a local
source for the required current.
4.5
PCB Layout Considerations
Proper Printed Circuit Board (PCB) layout is important
in high-current, fast-switching circuits to provide proper
device operation and robustness of design. Improper
component placement may cause errant switching,
excessive voltage ringing or circuit latch-up. The PCB
trace loop length and inductance should be minimized
by the use of ground planes or traces under the
MOSFET gate drive signal. Separate analog and
power grounds and local driver decoupling should also
be used.
P L = f CT V DD
2
Where:
f
=
CT
=
Total load capacitance
VDD
=
MOSFET driver supply voltage
4.6.2
Switching frequency
QUIESCENT POWER DISSIPATION
The power dissipation associated with the quiescent
current draw depends on the state of the Input and
Section 1.0
“Electrical
Enable
pins.
See
Characteristics” for typical quiescent current draw
values in different operating states. The quiescent
power dissipation is shown in Equation 4-3.
EQUATION 4-3:
P
Q
= I
QH
D + I QL 1 – D V DD
Where:
IQH
=
Quiescent current in the High state
D
=
Duty cycle
IQL
=
Quiescent current in the Low state
VDD
=
MOSFET driver supply voltage
Placing a ground plane beneath the MCP14A1201/2
devices will help as a radiated noise shield, as well as
providing some heat sinking for power dissipated within
the device.
2019 Microchip Technology Inc.
DS20006228A-page 13
MCP14A1201/2
4.6.3
OPERATING POWER DISSIPATION
The operating power dissipation occurs each time the
MOSFET driver output transitions because, for a very
short period of time, both MOSFETs in the output stage
are on simultaneously. This cross-conduction current
leads to a power dissipation described in Equation 4-4.
EQUATION 4-4:
P
CC
= V
DD
I CO
Where:
ICO
=
Crossover Current
VDD
=
MOSFET driver supply voltage
DS20006228A-page 14
2019 Microchip Technology Inc.
MCP14A1201/2
5.0
PACKAGING INFORMATION
5.1
Package Marking Information
8-Lead MSOP
Example
Device
MCP14A1201-E/MS
Code
A1201
MCP14A1201T-E/MS
A1201
MCP14A1202-E/MS
A1202
MCP14A1202T-E/MS
A1202
Note:
Applies to 8-Lead MSOP
Example
8-Lead SOIC
Device
MCP14A1201-E/SN
NNN
Code
14A1201
MCP14A1201T-E/SN
14A1201
MCP14A1202-E/SN
14A1202
MCP14A1202T-E/SN
14A1202
Note:
e3
Note:
256
Example:
Device
Code
MCP14A1201T-E/MNY
EM3
MCP14A1202T-E/MNY
EM4
Note:
*
14A1201
e31925
Applies to 8-Lead SOIC
8-Lead TDFN (2 x 3)
Legend: XX...X
Y
YY
WW
NNN
A01
5256
EM3
925
25
Applies to 8-Lead 2 x 3 TDFN
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will be carried over
to the next line, thus limiting the number of available characters for customer-specific
information.
2019 Microchip Technology Inc.
DS20006228A-page 15
MCP14A1201/2
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS20006228A-page 16
2019 Microchip Technology Inc.
MCP14A1201/2
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2019 Microchip Technology Inc.
DS20006228A-page 17
MCP14A1201/2
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS20006228A-page 18
2019 Microchip Technology Inc.
MCP14A1201/2
8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2X
0.10 C A–B
D
A
D
NOTE 5
N
E
2
E1
2
E1
E
NOTE 1
2
1
e
B
NX b
0.25
C A–B D
NOTE 5
TOP VIEW
0.10 C
C
A A2
SEATING
PLANE
8X
A1
SIDE VIEW
0.10 C
h
R0.13
h
R0.13
H
SEE VIEW C
VIEW A–A
0.23
L
(L1)
VIEW C
Microchip Technology Drawing No. C04-057-SN Rev E Sheet 1 of 2
2019 Microchip Technology Inc.
DS20006228A-page 19
MCP14A1201/2
8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Units
Dimension Limits
Number of Pins
N
e
Pitch
Overall Height
A
Molded Package Thickness
A2
§
Standoff
A1
Overall Width
E
Molded Package Width
E1
Overall Length
D
Chamfer (Optional)
h
Foot Length
L
Footprint
L1
Foot Angle
c
Lead Thickness
b
Lead Width
Mold Draft Angle Top
Mold Draft Angle Bottom
MIN
1.25
0.10
0.25
0.40
0°
0.17
0.31
5°
5°
MILLIMETERS
NOM
8
1.27 BSC
6.00 BSC
3.90 BSC
4.90 BSC
1.04 REF
-
MAX
1.75
0.25
0.50
1.27
8°
0.25
0.51
15°
15°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. § Significant Characteristic
3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or
protrusions shall not exceed 0.15mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
5. Datums A & B to be determined at Datum H.
Microchip Technology Drawing No. C04-057-SN Rev E Sheet 2 of 2
DS20006228A-page 20
2019 Microchip Technology Inc.
MCP14A1201/2
8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm Body [SOIC]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
SILK SCREEN
C
Y1
X1
E
RECOMMENDED LAND PATTERN
Units
Dimension Limits
Contact Pitch
E
Contact Pad Spacing
C
Contact Pad Width (X8)
X1
Contact Pad Length (X8)
Y1
MIN
MILLIMETERS
NOM
1.27 BSC
5.40
MAX
0.60
1.55
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing C04-2057-SN Rev E
2019 Microchip Technology Inc.
DS20006228A-page 21
MCP14A1201/2
8-Lead Plastic Dual Flat, No Lead Package (MNY) – 2x3x0.8 mm Body [TDFN]
With 1.4x1.3 mm Exposed Pad (JEDEC Package type WDFN)
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
A
B
N
(DATUM A)
(DATUM B)
E
NOTE 1
2X
0.15 C
1
2
2X
0.15 C
TOP VIEW
0.10 C
C
(A3)
A
SEATING
PLANE
8X
0.08 C
A1
SIDE VIEW
0.10
C A B
D2
L
1
2
0.10
C A B
NOTE 1
E2
K
N
8X b
e
0.10
0.05
C A B
C
BOTTOM VIEW
Microchip Technology Drawing No. C04-129-MNY Rev E Sheet 1 of 2
DS20006228A-page 22
2019 Microchip Technology Inc.
MCP14A1201/2
8-Lead Plastic Dual Flat, No Lead Package (MNY) – 2x3x0.8 mm Body [TDFN]
With 1.4x1.3 mm Exposed Pad (JEDEC Package type WDFN)
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Units
Dimension Limits
N
Number of Pins
e
Pitch
A
Overall Height
A1
Standoff
Contact Thickness
A3
D
Overall Length
E
Overall Width
Exposed Pad Length
D2
Exposed Pad Width
E2
b
Contact Width
L
Contact Length
Contact-to-Exposed Pad
K
MIN
0.70
0.00
1.35
1.25
0.20
0.25
0.20
MILLIMETERS
NOM
8
0.50 BSC
0.75
0.02
0.20 REF
2.00 BSC
3.00 BSC
1.40
1.30
0.25
0.30
-
MAX
0.80
0.05
1.45
1.35
0.30
0.45
-
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Package may have one or more exposed tie bars at ends.
3. Package is saw singulated
4. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing No. C04-129-MNY Rev E Sheet 2 of 2
2019 Microchip Technology Inc.
DS20006228A-page 23
MCP14A1201/2
8-Lead Plastic Dual Flat, No Lead Package (MNY) – 2x3x0.8 mm Body [TDFN]
With 1.4x1.3 mm Exposed Pad (JEDEC Package type WDFN)
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
X2
EV
8
ØV
C
Y2
EV
Y1
1
2
SILK SCREEN
X1
E
RECOMMENDED LAND PATTERN
Units
Dimension Limits
E
Contact Pitch
Optional Center Pad Width
X2
Optional Center Pad Length
Y2
Contact Pad Spacing
C
Contact Pad Width (X8)
X1
Contact Pad Length (X8)
Y1
Thermal Via Diameter
V
Thermal Via Pitch
EV
MIN
MILLIMETERS
NOM
0.50 BSC
MAX
1.60
1.50
2.90
0.25
0.85
0.30
1.00
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
2. For best soldering results, thermal vias, if used, should be filled or tented to avoid solder loss during
reflow process
Microchip Technology Drawing No. C04-129-MNY Rev. B
DS20006228A-page 24
2019 Microchip Technology Inc.
MCP14A1201/2
APPENDIX A:
REVISION HISTORY
Revision A (July 2019)
• Original release of this document.
2019 Microchip Technology Inc.
DS20006228A-page 25
MCP14A1201/2
NOTES:
DS20006228A-page 26
2019 Microchip Technology Inc.
MCP14A1201/2
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
[X](1)
–X
Device Tape and Reel Temperature
Range
Device:
/XX
E
Package:
MS
SN
MNY
Y*
= -40°C to +125°C (Extended)
= 8-Lead Plastic Micro Small Outline Package
(MSOP)
= 8-Lead Plastic Small Outline - Narrow, 3.90 mm
Body (SOIC)
= 8-Lead Plastic Dual Flat, No Lead Package 2 x 3 x 0.75 mm Body (TDFN)
= Nickel palladium gold manufacturing designator.
Only available on the SC70 and TDFN packages.
2019 Microchip Technology Inc.
a) MCP14A1201T-E/MS:
Tape and Reel,
Extended temperature,
8LD MSOP package
b) MCP14A1201-E/MS:
Extended temperature,
8LD MSOP package
c) MCP14A1202T-E/SN:
Tape and Reel,
Extended temperature,
8LD SOIC package
d) MCP14A1202-E/SN:
Extended temperature,
8LD SOIC package
Package
MCP14A1201:
High-Speed MOSFET Driver
MCP14A1202: High-Speed MOSFET Driver
MCP14A1201T: High-Speed MOSFET Driver
(Tape and Reel)
MCP14A1202T: High-Speed MOSFET Driver
(Tape and Reel)
Temperature Range:
Examples:
e) MCP14A1202T-E/MNY: Tape and Reel,
Extended temperature,
8LD TDFN package
Note 1:
Tape and Reel identifier only appears in the
catalog part number description. This
identifier is used for ordering purposes and
is not printed on the device package. Check
with your Microchip Sales Office for package
availability with the Tape and Reel option.
DS20006228A-page 27
MCP14A1201/2
NOTES:
DS20006228A-page 28
2019 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec,
AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, chipKIT,
chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex,
flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck,
LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi,
Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer,
PackeTime, PIC, picoPower, PICSTART, PIC32 logo, PolarFire,
Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST,
SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon,
TempTrackr, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA
are registered trademarks of Microchip Technology Incorporated in
the U.S.A. and other countries.
APT, ClockWorks, The Embedded Control Solutions Company,
EtherSynch, FlashTec, Hyper Speed Control, HyperLight Load,
IntelliMOS, Libero, motorBench, mTouch, Powermite 3, Precision
Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet-Wire,
SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub,
TimePictra, TimeProvider, Vite, WinPath, and ZL are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, BlueSky, BodyCom, CodeGuard,
CryptoAuthentication, CryptoAutomotive, CryptoCompanion,
CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average
Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial
Programming, ICSP, INICnet, Inter-Chip Connectivity, JitterBlocker,
KleerNet, KleerNet logo, memBrain, Mindi, MiWi, MPASM, MPF,
MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple
Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI,
SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC,
USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and
ZENA are trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage
Technology, and Symmcom are registered trademarks of Microchip
Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany
II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in
other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2019, Microchip Technology Incorporated, All Rights Reserved.
For information regarding Microchip’s Quality Management Systems,
please visit www.microchip.com/quality.
2019 Microchip Technology Inc.
ISBN: 978-1-5224-4773-3
DS20006228A-page 29
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
Finland - Espoo
Tel: 358-9-4520-820
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
DS20006228A-page 30
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-72400
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7288-4388
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
2019 Microchip Technology Inc.
05/14/19