MCP3202T-BI/SN

MCP3202 2.7V Dual Channel 12-Bit A/D Converter with SPI Serial Interface Features Description • • • • • The MCP3202 is a successive approximation 12-bit analog-to-digital (A/D) converter with on-board sample and hold circuitry. • • • • • • • • • • 12-bit resolution ±1 LSB maximum DNL ±1 LSB maximum INL (MCP3202-B) ±2 LSB maximum INL (MCP3202-C) Analog inputs programmable as single-ended or pseudo-differential pairs On-chip sample and hold SPI Serial Interface (Modes 0,0 and 1,1) Single supply operation: 2.7V-5.5V 100 ksps maximum sampling rate at VDD = 5V 50 ksps maximum sampling rate at VDD = 2.7V Low power CMOS technology 500 nA typical standby current, 5 µA maximum 550 µA maximum active current at 5V Industrial temp range: -40°C to +85°C 8-pin MSOP, PDIP, SOIC and TSSOP packages Applications • • • • Sensor Interface Process Control Data Acquisition Battery Operated Systems The MCP3202 operates over a broad voltage range, 2.7V to 5.5V. Low-current design permits operation with typical standby and active currents of only 500 nA and 375 µA, respectively. The MCP3202 is offered in 8-pin MSOP, PDIP, TSSOP and 150 mil SOIC packages. PDIP, MSOP, SOIC, TSSOP CS/SHDN 1 CH0 2 CH1 3 VSS 4 MCP3202 VDD VSS Input Channel Mux Communication with the device is done using a simple serial interface compatible with the SPI protocol. The device is capable of conversion rates of up to 100 ksps at 5V and 50 ksps at 2.7V. Package Types Functional Block Diagram CH0 CH1 The MCP3202 is programmable to provide a single pseudo-differential input pair or dual single-ended inputs. Differential Nonlinearity (DNL) is specified at ±1 LSB, and Integral Nonlinearity (INL) is offered in ±1 LSB (MCP3202-B) and ±2 LSB (MCP3202-C) versions. 8 VDD/VREF 7 CLK 6 DOUT 5 DIN DAC Comparator 12-Bit SAR Sample and Hold Control Logic CS/SHDN DIN CLK  1999-2011 Microchip Technology Inc. Shift Register DOUT DS21034F-page 1 MCP3202 1.0 ELECTRICAL CHARACTERISTICS † Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings † VDD - VSS .........................................................................7.0V All Inputs and Outputs w.r.t. VSS ............. -0.6V to VDD + 0.6V Storage Temperature.....................................-65°C to +150°C Ambient temperature with power applied.......-65°C to +150°C Maximum Junction Temperature (TJ) ......................... .+150°C ESD Protection On All Pins (HBM)  4 kV ELECTRICAL CHARACTERISTICS Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5.5V, VSS = 0V, TA = -40°C to +85°C, fSAMPLE = 100 ksps and fCLK = 18*fSAMPLE. Parameter Conversion Rate: Conversion Time Sym Min. Typ. Max. Units tCONV — — 12 clock cycles clock cycles 100 50 ksps ksps ±1 ±2 ±1 bits LSB LSB LSB Analog Input Sample Time tSAMPLE Throughput Rate fSAMPL Resolution Integral Nonlinearity INL Differential Nonlinearity DNL Offset Error Gain Error Total Harmonic Distortion Signal-to-Noise and Distortion (SINAD) Spurious Free Dynamic Range Input Voltage Range for CH0 or CH1 in Single-Ended Mode Input Voltage Range for IN+ in Pseudo-Differential Mode Input Voltage Range for IN- in Pseudo-Differential Mode Leakage Current Switch Resistance Sample Capacitor Data Coding Format High Level Input Voltage Low Level Input Voltage THD SINAD SFDR 1.5 — — — — DC Accuracy: 12 — ±0.75 — ±1 — ±0.5 — ±1.25 ±3 — ±1.25 ±5 Dynamic Performance: — -82 — — 72 — — 86 — Analog Inputs: — VDD VSS Conditions VDD = VREF = 5V VDD = VREF = 2.7V MCP3202-B MCP3202-C No missing codes over temperature LSB LSB dB dB VIN = 0.1V to 4.9V@1 kHz VIN = 0.1V to 4.9V@1 kHz dB VIN = 0.1V to 4.9V@1 kHz V IN+ IN- — VDD+IN- IN- VSS-100 — VSS+100 mV See Sections 3.1 and 4.1 — .001 ±1 — 1k — — 20 — Digital Input/Output: Straight Binary 0.7 VDD — — — — 0.3 VDD A Ω pF See Figure 4-1 See Figure 4-1 RSS CSAMPLE VIH VIL See Sections 3.1 and 4.1 V V Note 1: This parameter is established by characterization and not 100% tested. 2: Because the sample cap will eventually lose charge, effective clock rates below 10 kHz can affect linearity performance, especially at elevated temperatures. See Section 6.2 “Maintaining Minimum Clock Speed” for more information. DS21034F-page 2  1999-2011 Microchip Technology Inc. MCP3202 ELECTRICAL CHARACTERISTICS (CONTINUED) Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5.5V, VSS = 0V, TA = -40°C to +85°C, fSAMPLE = 100 ksps and fCLK = 18*fSAMPLE. Parameter High Level Output Voltage Low Level Output Voltage Input Leakage Current Output Leakage Current Pin Capacitance (All Inputs/Outputs) Timing Parameters: Clock Frequency Sym Min. Typ. Max. Units VOH VOL ILI ILO CIN, COUT 4.1 — -10 -10 — — — — — — — 0.4 10 10 10 V V µA µA pF fCLK — — tSUCS 100 — — — 1.8 0.9 2 2 — MHz MHz MHz MHz ns tSU tHD tDO tEN tDIS 50 50 — — — — — — — — — — 200 200 100 ns ns ns ns ns tCSH tR 500 — — — — 100 ns ns tF — — 100 ns VDD IDD IDDS 2.7 — — — 375 0.5 5.5 550 5 V µA µA Clock High Time Clock Low Time CS Fall To First Rising CLK Edge Data Input Setup Time Data Input Hold Time CLK Fall To Output Data Valid CLK Fall To Output Enable CS Rise To Output Disable CS Disable Time DOUT Rise Time DOUT Fall Time Power Requirements: Operating Voltage Operating Current Standby Current tHI tLO Conditions IOH = -1 mA, VDD = 4.5V IOL = 1 mA, VDD = 4.5V VIN = VSS or VDD VOUT = VSS or VDD VDD = 5.0V (Note 1) TA = +25°C, f = 1 MHz VDD = 5V (Note 2) VDD = 2.7V (Note 2) See Test Circuits, Figure 1-2 See Test Circuits, Figure 1-2 See Test Circuits, Figure 1-2 Note 1 See Test Circuits, Figure 1-2 Note 1 See Test Circuits, Figure 1-2 Note 1 VDD = 5.0V, DOUT unloaded CS = VDD = 5.0V Note 1: This parameter is established by characterization and not 100% tested. 2: Because the sample cap will eventually lose charge, effective clock rates below 10 kHz can affect linearity performance, especially at elevated temperatures. See Section 6.2 “Maintaining Minimum Clock Speed” for more information. TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, VDD = +2.7V to +5.5V, VSS = GND. Parameters Sym Min Typ Max Units Specified Temperature Range TA -40 — +85 °C Operating Temperature Range TA -40 — +85 °C Storage Temperature Range TA -65 — +150 °C Conditions Temperature Ranges Thermal Package Resistances Thermal Resistance, 8L-MSOP JA — 211 — °C/W Thermal Resistance, 8L-PDIP JA — 89.5 — °C/W Thermal Resistance, 8L-SOIC JA — 149.5 — °C/W Thermal Resistance, 8L-TSSOP JA — 139 — °C/W  1999-2011 Microchip Technology Inc. DS21034F-page 3 MCP3202 tCSH CS tSUCS tHI tLO CLK tSU DIN tHD MSB IN tEN DOUT FIGURE 1-1: DS21034F-page 4 tR tDO NULL BIT MSB OUT tF tDIS LSB Serial Timing.  1999-2011 Microchip Technology Inc. MCP3202 Load Circuit for tDIS and tEN Load Circuit for tR, tF, tDO Test Point 1.4V VDD 3 kΩ Test Point DOUT 3 kΩ DOUT VDD /2 100 pF tEN Waveform tDIS Waveform 1 VSS CL = 100 pF tDIS Waveform 2 Voltage Waveforms for tEN Voltage Waveforms for tR, tF VOH VOL DOUT tF tR CS 1 CLK 2 3 4 B11 DOUT tEN Voltage Waveforms for tDO Voltage Waveforms for tDIS CS CLK tDO VIH DOUT Waveform 1* 90% TDIS DOUT DOUT Waveform 2† 10% * Waveform 1 is for an output with internal conditions such that the output is high, unless disabled by the output control. † Waveform 2 is for an output with internal conditions such that the output is low, unless disabled by the output control. FIGURE 1-2: Test Circuits.  1999-2011 Microchip Technology Inc. DS21034F-page 5 MCP3202 2.0 TYPICAL PERFORMANCE CHARACTERISTICS Note: The graphs provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 18* fSAMPLE, TA = +25°C. 1.0 2.0 0.8 Positive INL VDD = 2.7V 1.5 0.6 Positive INL 1.0 INL (LSB) 0.4 ) B 0.2 S L ( 0.0 L -0.2 IN Negative INL -0.4 0.5 0.0 -0.5 Negative INL -1.0 -0.6 -1.5 -0.8 -2.0 -1.0 0 25 50 75 100 125 0 150 20 40 Integral Nonlinearity (INL) 1.0 fSAMPLE = 100 ksps Positive INL 0.6 0.4 INL (LSB) INL (LSB) fSAMPLE = 50 ksps 0.8 Positive INL 0.6 0.2 0.0 -0.2 -0.4 Negative INL -0.6 0.4 0.2 0.0 -0.2 -0.4 Negative INL -0.6 -0.8 -0.8 -1.0 3.0 3.5 4.0 4.5 -1.0 5.0 2.5 3.0 3.5 VDD(V) FIGURE 2-2: vs. VDD. 4.0 4.5 5.0 VDD(V) Integral Nonlinearity (INL) FIGURE 2-5: vs. VDD. 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 INL (LSB) INL (LSB) 100 FIGURE 2-4: Integral Nonlinearity (INL) vs. Sample Rate (VDD = 2.7V). 1.0 0.8 80 Sample Rate (ksps) Sample Rate (ksps) FIGURE 2-1: vs. Sample Rate. 60 0.2 0.0 -0.2 -0.4 VDD = 2.7V FSAMPLE = 50 ksps 0.2 0.0 -0.2 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 Integral Nonlinearity (INL) -1.0 0 512 1024 1536 2048 2560 3072 3584 4096 Digital Code FIGURE 2-3: Integral Nonlinearity (INL) vs. Code (Representative Part). DS21034F-page 6 0 512 1024 1536 2048 2560 3072 3584 4096 Digital Code FIGURE 2-6: Integral Nonlinearity (INL) vs. Code (Representative Part, VDD = 2.7V).  1999-2011 Microchip Technology Inc. MCP3202 Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 18* fSAMPLE, TA = +25°C. 1.0 1.0 0.6 0.6 0.4 0.4 0.2 0.0 Negative INL -0.2 VDD = 2.7V fSAMPLE = 50 ksps 0.8 Positive INL INL (LSB) INL (LSB) 0.8 Positive INL 0.2 0.0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 Negative INL -1.0 -1.0 -50 -25 0 25 50 75 -50 100 -25 25 50 75 100 Temperature (°C) Temperature (°C) FIGURE 2-7: vs. Temperature. 0 Integral Nonlinearity (INL) FIGURE 2-10: Integral Nonlinearity (INL) vs. Temperature (VDD = 2.7V). 0.8 2.0 0.6 1.5 0.4 Positive DNL DNL (LSB) DNL (LSB) 1.0 0.2 0.0 -0.2 Negative DNL -0.4 1.0 Positive DNL 0.5 0.0 -0.5 -0.6 -1.0 -0.8 -1.5 -1.0 VDD = 2.7V Negative DNL -2.0 0 25 50 75 100 125 150 0 20 Sample Rate (ksps) FIGURE 2-8: Differential Nonlinearity (DNL) vs. Sample Rate. 1.0 0.6 0.2 0.0 -0.2 -0.4 Negative DNL -0.6 100 fSAMPLE = 50 ksps 0.8 Positive DNL 0.4 80 1.0 DNL (LSB) DNL (LSB) 0.6 60 FIGURE 2-11: Differential Nonlinearity (DNL) vs. Sample Rate (VDD = 2.7V). fSAMPLE = 100 ksps 0.8 40 Sample Rate (ksps) Positive DNL 0.4 0.2 0.0 -0.2 -0.4 Negative DNL -0.6 -0.8 -0.8 -1.0 3.0 3.5 4.0 4.5 5.0 -1.0 2.5 VDD(V) FIGURE 2-9: (DNL) vs. VDD. Differential Nonlinearity  1999-2011 Microchip Technology Inc. 3.0 3.5 4.0 4.5 5.0 VDD(V) FIGURE 2-12: (DNL) vs. VDD. Differential Nonlinearity DS21034F-page 7 MCP3202 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 DNL (LSB) DNL (LSB) Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 18* fSAMPLE, TA = +25°C. 0.2 0.0 -0.2 -0.4 VDD = 2.7V fSAMPLE = 50 ksps 0.2 0.0 -0.2 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -1.0 0 512 1024 1536 2048 2560 3072 3584 0 4096 512 1024 1536 Digital Code 0.8 0.6 0.6 Positive DNL DNL (LSB) DNL (LSB) 1.0 0.8 0.2 0.0 Negative DNL -0.4 0.0 25 50 75 Negative DNL -0.4 -0.8 -1.0 Positive DNL -0.2 -0.6 0 -1.0 100 -50 -25 Temperature (°C) 0 25 50 75 100 Temperature (°C) FIGURE 2-14: Differential Nonlinearity (DNL) vs. Temperature. FIGURE 2-17: Differential Nonlinearity (DNL) vs. Temperature (VDD = 2.7V). 2.0 2.0 1.5 1.8 fSAMPLE = 10 ksps 1.0 Offset Error (LSB) Gain Error (LSB) 4096 0.2 -0.8 -25 3584 VDD = 2.7V fSAMPLE = 50 ksps 0.4 -0.6 -50 3072 FIGURE 2-16: Differential Nonlinearity (DNL) vs. Code (Representative Part, VDD = 2.7V). 1.0 -0.2 2560 Digital Code FIGURE 2-13: Differential Nonlinearity (DNL) vs. Code (Representative Part). 0.4 2048 0.5 0.0 -0.5 -1.0 fSAMPLE = 100 ksps -1.5 2.5 3.0 3.5 4.0 4.5 VDD(V) FIGURE 2-15: DS21034F-page 8 1.4 fSAMPLE = 50 ksps 1.2 1.0 0.8 0.6 0.4 fSAMPLE = 10 ksps 0.2 fSAMPLE = 50 ksps -2.0 fSAMPLE = 100 ksps 1.6 Gain Error vs. VDD. 5.0 0.0 2.5 3.0 3.5 4.0 4.5 5.0 VDD(V) FIGURE 2-18: Offset Error vs. VDD.  1999-2011 Microchip Technology Inc. MCP3202 Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 18* fSAMPLE, TA = +25°C. 1.0 2.0 1.8 VDD = 2.7V fSAMPLE = 50 ksps 0.6 0.4 Offset Error (LSB) Gain Error (LSB) 0.8 0.2 0.0 -0.2 -0.4 -0.6 VDD = 5V fSAMPLE = 100 -0.8 -1.0 -50 -25 0 25 50 75 VDD = 5V fSAMPLE = 100 ksps 1.6 1.4 1.2 1.0 0.8 VDD = 2.7V fSAMPLE = 50 ksps 0.6 0.4 0.2 0.0 -50 100 -25 0 Temperature (°C) FIGURE 2-19: FIGURE 2-22: Temperature. 75 100 Offset Error vs. 100 VDD = 5V fSAMPLE = 100 ksps 90 80 80 70 60 VDD = 2.7V fSAMPLE = 50 ksps 50 40 VDD = 5V fSAMPLE = 100 ksps 90 70 SINAD (dB) SNR (dB) 50 Temperature (°C) Gain Error vs. Temperature. 100 30 60 50 VDD = 2.7V fSAMPLE = 50 ksps 40 30 20 20 10 10 0 0 1 10 1 100 10 FIGURE 2-23: Signal-to-Noise and Distortion (SINAD) vs. Input Frequency. FIGURE 2-20: Signal-to-Noise Ratio (SNR) vs. Input Frequency. 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 100 Input Frequency (kHz) Input Frequency (kHz) 80 VDD = 5V f SAMPLE = 100 ksps 70 SINAD (dB) THD (dB) 25 VDD = 2.7V fSAMPLE = 50 ksps VDD = 5V fSAMPLE = 100 ksps 60 50 VDD = 2.7V fSAMPLE = 50 ksps 40 30 20 10 0 1 10 100 Input Frequency (kHz) FIGURE 2-21: Total Harmonic Distortion (THD) vs. Input Frequency.  1999-2011 Microchip Technology Inc. -40 -35 -30 -25 -20 -15 -10 -5 0 Input Signal Level (dB) FIGURE 2-24: Signal-to-Noise and Distortion (SINAD) vs. Signal Level. DS21034F-page 9 MCP3202 Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 18* fSAMPLE, TA = +25°C. 12.0 12.0 fSAMPLE = 50ksps 11.5 FSAMPLE = 100 ksps 11.0 ENOB (rms) ENOB (rms) VDD = 5V 11.5 11.0 fSAMPLE = 100 ksps 10.5 10.0 10.5 10.0 9.5 9.0 9.5 VDD = 2.7V 8.5 9.0 2.0 2.5 3.0 3.5 4.0 4.5 FSAMPLE = 50 ksps 8.0 5.0 1 10 VDD (V) FIGURE 2-25: (ENOB) vs. VDD. 100 Input Frequency (kHz) Effective Number of Bits FIGURE 2-28: Effective Number of Bits (ENOB) vs. Input Frequency. VDD = 5V fSAMPLE = 100 ksps VDD = 2.7V fSAMPLE = 50 ksps 1 10 100 Power Supply Rejection (dB) SFDR (dB) 0 100 90 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 -50 -60 -70 -80 1 10 Input Frequency (kHz) fINPUT = 9.985 kHz 4096 points 20000 30000 40000 50000 Frequency (Hz) FIGURE 2-27: Frequency Spectrum of 10 kHz input (Representative Part). DS21034F-page 10 Amplitude (dB) Amplitude (dB) fSAMPLE = 100 ksps 10000 10000 FIGURE 2-29: Power Supply Rejection (PSR) vs. Ripple Frequency. VDD = 5V 0 1000 Ripple Frequency (kHz) FIGURE 2-26: Spurious Free Dynamic Range (SFDR) vs. Input Frequency. 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 100 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 VDD = 2.7V fSAMPLE = 50 ksps fINPUT = 998.76 Hz 4096 points 0 5000 10000 15000 20000 25000 Frequency (Hz) FIGURE 2-30: Frequency Spectrum of 1 kHz input (Representative Part, VDD = 2.7V).  1999-2011 Microchip Technology Inc. MCP3202 Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 18* fSAMPLE, TA = +25°C. 500 at VDD = 2.5V, FCLK = 900 kHz 400 CS = VDD 70 350 60 300 50 IDDS (pA) IDD (µA) 80 All points at FCLK = 1.8 MHz except 450 250 200 40 30 150 20 100 10 50 0 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 2.0 2.5 3.0 3.5 4.5 5.0 5.5 6.0 VDD (V) VDD (V) FIGURE 2-31: 4.0 IDD vs. VDD. IDDS vs. VDD. FIGURE 2-34: 500 100.00 450 400 10.00 IDDS (nA) IDD (µA) VDD =CS =5V V DD = 5V 350 300 250 V DD = 2.7V 200 150 1.00 0.10 100 50 0.01 0 - 50 10 100 1000 -25 IDD vs. Clock Frequency. FIGURE 2-35: 500 400 FCLK = 1.8 MHz IDD (µA) 350 300 250 200 VDD = 2.7V 150 FCLK = 900 kHz 100 50 0 -50 -25 0 25 50 75 Temperature (°C) FIGURE 2-33: 50 75 100 IDDS vs. Temperature. 2.0 VDD = 5V Analog Input Leakage (nA) 450 25 Tem perature (°C) Clock Frequency (kHz) FIGURE 2-32: 0 10000 IDD vs. Temperature.  1999-2011 Microchip Technology Inc. 100 1.8 1.6 1.4 1.2 VDD = 5V 1.0 FCLK = 1.8 MHz 0.8 0.6 0.4 0.2 0.0 -50 -25 0 25 50 75 100 Temperature (°C) FIGURE 2-36: Analog Input leakage current vs. Temperature. DS21034F-page 11 MCP3202 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3.1. Additional descriptions of the device pins follows. TABLE 3-1: PIN FUNCTION TABLE MSOP, PDIP, SOIC, TSSOP Name 1 CS/SHDN 2 CH0 Channel 0 Analog Input 3 CH1 Channel 1 Analog Input 4 VSS Ground 5 DIN Serial Data In 6 DOUT Serial Data Out 7 CLK Serial Clock 8 VDD/VREF 3.1 Function Chip Select/Shutdown Input +2.7V to 5.5V Power Supply and Reference Voltage Input Analog Inputs (CH0/CH1) Analog inputs for channels 0 and 1 respectively. These channels can be programmed to be used as two independent channels in Single-Ended mode or as a single pseudo-differential input where one channel is IN+ and one channel is IN-. See Section 5.0 “Serial Communications” for information on programming the channel configuration. 3.2 Chip Select/Shutdown (CS/SHDN) The CS/SHDN pin is used to initiate communication with the device when pulled low and will end a conversion and put the device in low power standby when pulled high. The CS/SHDN pin must be pulled high between conversions. DS21034F-page 12 3.3 Serial Clock (CLK) The SPI clock pin is used to initiate a conversion and to clock out each bit of the conversion as it takes place. See Section 6.2 “Maintaining Minimum Clock Speed” for constraints on clock speed. 3.4 Serial Data Input (DIN) The SPI port serial data input pin is used to clock in input channel configuration data. 3.5 Serial Data Output (DOUT) The SPI serial data output pin is used to shift out the results of the A/D conversion. Data will always change on the falling edge of each clock as the conversion takes place.  1999-2011 Microchip Technology Inc. MCP3202 4.0 DEVICE OPERATION The MCP3202 A/D converter employs a conventional SAR architecture. With this architecture, a sample is acquired on an internal sample/hold capacitor for 1.5 clock cycles starting on the second rising edge of the serial clock after the start bit has been received. Following this sample time, the input switch of the converter opens and the device uses the collected charge on the internal sample and hold capacitor to produce a serial 12-bit digital output code. Conversion rates of 100 ksps are possible on the MCP3202. See Section 6.2 “Maintaining Minimum Clock Speed” for information on minimum clock rates. Communication with the device is done using a 3-wire SPI-compatible interface. 4.1 4.2 Digital Output Code The digital output code produced by an A/D converter is a function of the input signal and the reference voltage. For the MCP3202, VDD is used as the reference voltage. As the VDD level is reduced, the LSB size is reduced accordingly. The theoretical digital output code produced by the A/D converter is shown below. EQUATION 4-1: 4096•VIN Digital Output Code = ----------------------VDD where: VIN = analog input voltage VDD = supply voltage Analog Inputs The MCP3202 device offers the choice of using the analog input channels configured as two single-ended inputs or a single pseudo-differential input. Configuration is done as part of the serial command before each conversion begins. When used in the pseudo-differential mode, CH0 and CH1 are programmed as the IN+ and IN- inputs as part of the command string transmitted to the device. The IN+ input can range from IN- to VREF (VDD + IN-). The IN- input is limited to ±100 mV from the VSS rail. The IN- input can be used to cancel small signal common-mode noise which is present on both the IN+ and IN- inputs. For the A/D converter to meet specification, the charge holding capacitor (CSAMPLE) must be given enough time to acquire a 12-bit accurate voltage level during the 1.5 clock cycle sampling period. The analog input model is shown in Figure 4-1. In this diagram, it is shown that the source impedance (RS) adds to the internal sampling switch (RSS) impedance, directly affecting the time that is required to charge the capacitor, CSAMPLE. Consequently, larger source impedances increase the offset, gain, and integral linearity errors of the conversion. Ideally, the impedance of the signal source should be near zero. This is achievable with an operational amplifier such as the MCP601 which has a closed loop output impedance of tens of ohms. The adverse affects of higher source impedances are shown in Figure 4-2. When operating in the pseudo-differential mode, if the voltage level of IN+ is equal to or less than IN-, the resultant code will be 000h. If the voltage at IN+ is equal to or greater than {[VDD +(IN-)] -1 LSB}, then the output code will be FFFh. If the voltage level at IN- is more than 1 LSB below VSS, then the voltage level at the IN+ input will have to go below VSS to see the 000h output code. Conversely, if IN- is more than 1 LSB above VSS, then the FFFh code will not be seen unless the IN+ input level goes above VDD level.  1999-2011 Microchip Technology Inc. DS21034F-page 13 MCP3202 VDD RSS Sampling Switch VT = 0.6V CHx CPIN 7 pF VA VT= 0.6V SS ILEAKAGE ±1 nA RS = 1 kW CSAMPLE = DAC capacitance = 20 pF VSS Legend VA RSS CHx CPIN VT ILEAKAGE SS RS CSAMPLE FIGURE 4-1: = = = = = = = = = signal source source impedance input channel pad input pin capacitance threshold voltage leakage current at the pin due to various junctions sampling switch sampling switch resistor sample/hold capacitance Analog Input Model. Clock Frequency (MHz) 2.0 1.8 VDD = 5V 1.6 1.4 1.2 1.0 0.8 0.6 V DD = 2.7V 0.4 0.2 0.0 100 1000 10000 Input Resistance (Ohms) FIGURE 4-2: Maximum Clock Frequency vs. Input Resistance (RS) to maintain less than a 0.1 LSB deviation in INL from nominal conditions. DS21034F-page 14  1999-2011 Microchip Technology Inc. MCP3202 5.0 SERIAL COMMUNICATIONS 5.1 Overview Communication with the MCP3202 is done using a standard SPI-compatible serial interface. Initiating communication with the device is done by bringing the CS line low. See Figure 5-1. If the device was powered up with the CS pin low, it must be brought high and back low to initiate communication. The first clock received with CS low and DIN high will constitute a start bit. The SGL/DIFF bit and the ODD/SIGN bit follow the start bit and are used to select the input channel configuration. The SGL/DIFF is used to select Single-Ended or Pseudo-Differential mode. The ODD/SIGN bit selects which channel is used in Single-Ended mode, and is used to determine polarity in Pseudo-Differential mode. Following the ODD/SIGN bit, the MSBF bit is transmitted to and is used to enable the LSB first format for the device. If the MSBF bit is high, then the data will come from the device in MSB first format and any further clocks with CS low will cause the device to output zeros. If the MSBF bit is low, then the device will output the converted word LSB first after the word has been transmitted in the MSB first format. See Figure 5-2. Table 5-1 shows the configuration bits for the MCP3202. The device will begin to sample the analog input on the second rising edge of the clock, after the start bit has been received. The sample period will end on the falling edge of the third clock following the start bit. On the falling edge of the clock for the MSBF bit, the device will output a low null bit. The next sequential 12 clocks will output the result of the conversion with MSB first as shown in Figure 5-1. Data is always output from the device on the falling edge of the clock. If all 12 data bits have been transmitted and the device continues to receive clocks while the CS is held low, (and MSBF = 1), the device will output the conversion result LSB first as shown in Figure 5-2. If more clocks are provided to the device while CS is still low (after the LSB first data has been transmitted), the device will clock out zeros indefinitely. If necessary, it is possible to bring CS low and clock in leading zeros on the DIN line before the start bit. This is often done when dealing with microcontroller-based SPI ports that must send 8 bits at a time. Refer to Section 6.1 “Using the MCP3202 with Microcontroller (MCU) SPI Ports” for more details on using the MCP3202 devices with hardware SPI ports. TABLE 5-1: CONFIGURATION BITS FOR THE MCP3202 Config Bits Channel Selection SGL/ ODD/ DIFF SIGN 0 1 GND Single-Ended Mode 1 0 + — - 1 1 — + - PseudoDifferential Mode 0 0 IN+ IN- 0 1 IN- IN+ tCYC tCYC tCSH CS tSUCS CLK Start SGL/ ODD/ MS DIFF SIGN BF DIN HI-Z DOUT Start SGL/ ODD/ DIFF SIGN Don’t Care Null Bit B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0* tCONV tSAMPLE HI-Z tDATA** * After completing the data transfer, if further clocks are applied with CS low, the A/D converter will output zeros indefinitely. See Figure 5-2 below for details on obtaining LSB first data. ** tDATA: during this time, the bias current and the comparator power down while the reference input becomes a high-impedance node, leaving the CLK running to clock out the LSB-first data or zeros. FIGURE 5-1: Communication with the MCP3202 using MSB first format only.  1999-2011 Microchip Technology Inc. DS21034F-page 15 MCP3202 tCYC tCSH CS tSUCS Power Down HI-Z DOUT tSAMPLE MSBF SGL/ DIFF ODD/ SIGN DIN Start CLK Don’t Care Null B11 B10 B9 Bit B8 B7 B6 B5 B4 B3 B2 B1 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 * HI-Z (MSB) tDATA ** tCONV * After completing the data transfer, if further clocks are applied with CS low, the A/D converter will output zeros indefinitely. ** tDATA: During this time, the bias circuit and the comparator power down while the reference input becomes a high-impedance node, leaving the CLK running to clock out LSB first data or zeroes. FIGURE 5-2: DS21034F-page 16 Communication with MCP3202 using LSB first format.  1999-2011 Microchip Technology Inc. MCP3202 6.0 APPLICATIONS INFORMATION 6.1 Using the MCP3202 with Microcontroller (MCU) SPI Ports Figure 6-1 depicts the operation shown in SPI Mode 0,0, which requires that the SCLK from the MCU idles in the ‘low’ state, while Figure 6-2 shows the similar case of SPI Mode 1,1 where the clock idles in the ‘high’ state. With most microcontroller SPI ports, it is required to send groups of eight bits. It is also required that the microcontroller SPI port be configured to clock out data on the falling edge of clock and latch data in on the rising edge. Depending on how communication routines are used, it is very possible that the number of clocks required for communication will not be a multiple of eight. Therefore, it may be necessary for the MCU to send more clocks than are actually required. This is usually done by sending ‘leading zeros’ before the start bit, which are ignored by the device. As shown in Figure 6-1, the first byte transmitted to the A/D converter contains seven leading zeros before the start bit. Arranging the leading zeros this way produces the output 12 bits to fall in positions easily manipulated by the MCU. The MSB is clocked out of the A/D converter on the falling edge of clock number 12. After the second eight clocks have been sent to the device, the MCU receive buffer will contain three unknown bits (the output is at high-impedance until the null bit is clocked out), the null bit and the highest order four bits of the conversion. After the third byte has been sent to the device, the receive register will contain the lowest order eight bits of the conversion results. Easier manipulation of the converted data can be obtained by using this method. As an example, Figure 6-1 and Figure 6-2 show how the MCP3202 can be interfaced to a MCU with a hardware SPI port. CS MCU latches data from A/D converter on rising edges of SCLK SCLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 B5 B4 21 22 23 24 B2 B1 B0 X X Don’t Care HI-Z DOUT MCU Received Data (Aligned with rising edge of clock) NULL B11 BIT B10 B9 B8 X X X B7 B6 B3 Start Bit MCU Transmitted Data (Aligned with falling edge of clock) X X X X X X X X X X X X X SGL/ ODD/ MSBF DIFF SIGN 1 X X X Data stored into MCU receive register after transmission of first 8 bits X = Don’t Care Bits FIGURE 6-1: CS SGL/ DIFF Start MSBF DIN ODD/ SIGN Data is clocked out of A/D converter on falling edges X X X 0 B11 (Null) B10 B9 X X B7 B8 Data stored into MCU receive register after transmission of second 8 bits X B6 X B5 X B4 X B3 B2 B1 X B0 Data stored into MCU receive register after transmission of last 8 bits SPI Communication using 8-bit segments (Mode 0,0: SCLK idles low). MCU latches data from A/D converter on rising edges of SCLK SCLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 B5 B4 B3 B2 B1 B0 MCU Received Data (Aligned with rising edge of clock) X = Don’t Care Bits FIGURE 6-2: MSBF Don’t Care HI-Z DOUT MCU Transmitted Data (Aligned with falling edge of clock) SGL/ DIFF Start DIN ODD/ SIGN Data is clocked out of A/D converter on falling edges NULL B11 BIT Start Bit 0 0 X 0 X 0 X 0 X X X SGL/ ODD/ MSBF DIFF SIGN 1 0 0 X X Data stored into MCU receive register after transmission of first 8 bits X X X X X 0 B11 (Null) B10 B9 X X B10 B8 X X B9 B6 B7 B8 Data stored into MCU receive register after transmission of second 8 bits X B7 X B6 X B5 X B4 X B3 X B2 X B1 B0 Data stored into MCU receive register after transmission of last 8 bits SPI Communication using 8-bit segments (Mode 1,1: SCLK idles high).  1999-2011 Microchip Technology Inc. DS21034F-page 17 MCP3202 6.2 Maintaining Minimum Clock Speed When the MCP3202 initiates the sample period, charge is stored on the sample capacitor. When the sample period is complete, the device converts one bit for each clock that is received. It is important for the user to note that a slow clock rate will allow charge to bleed off the sample cap while the conversion is taking place. At 85°C (worst case condition), the part will maintain proper charge on the sample capacitor for at least 1.2 ms after the sample period has ended. This means that the time between the end of the sample period and the time that all 12 data bits have been clocked out must not exceed 1.2 ms (effective clock frequency of 10 kHz). Failure to meet this criteria may induce linearity errors into the conversion outside the rated specifications. It should be noted that during the entire conversion cycle, the A/D converter does not require a constant clock speed or duty cycle, as long as all timing specifications are met. 6.3 Buffering/Filtering the Analog Inputs If the signal source for the A/D converter is not a lowimpedance source, it will have to be buffered or inaccurate conversion results may occur. It is also recommended that a filter be used to eliminate any signals that may be aliased back into the conversion results. This is illustrated in Figure 6-3 below where an op amp is used to drive the analog input of the MCP3202. This amplifier provides a low-impedance output for the converter input and a low-pass filter, which eliminates unwanted high frequency noise. Low-pass (anti-aliasing) filters can be designed using Microchip’s interactive FilterLab® software. FilterLab will calculate capacitor and resistor values, as well as, determine the number of poles that are required for the application. For more information on filtering signals, see the application note AN699 “Anti-Aliasing Analog Filters for Data Acquisition Systems”. 6.4 Layout Considerations When laying out a printed circuit board for use with analog components, care should be taken to reduce noise wherever possible. A bypass capacitor should always be used with this device and should be placed as close as possible to the device pin. A bypass capacitor value of 0.1 µF is recommended. Digital and analog traces should be separated as much as possible on the board and no traces should run underneath the device or the bypass capacitor. Extra precautions should be taken to keep traces with high frequency signals (such as clock lines) as far as possible from analog traces. Use of an analog ground plane is recommended in order to keep the ground potential the same for all devices on the board. Providing VDD connections to devices in a “star” configuration can also reduce noise by eliminating current return paths and associated errors. See Figure 6-4. For more information on layout tips when using A/D converters, refer to AN688 “Layout Tips for 12-Bit A/D Converter Applications” (DS00688). VDD Connection Device 4 Device 1 Device 3 Device 2 ” VDD 10 µF VIN R1 C1 R2 C2 MCP601 + - R4 FIGURE 6-4: VDD traces arranged in a ‘Star’ configuration in order to reduce errors caused by current return paths. 0.1 µF IN+ MCP3202 IN- R3 FIGURE 6-3: The MCP601 Operational Amplifier is used to implement a 2nd order antialiasing filter for the signal being converted by the MCP3202. DS21034F-page 18  1999-2011 Microchip Technology Inc. MCP3202 7.0 PACKAGING INFORMATION 7.1 Package Marking Information 8-Lead MSOP (3x3 mm) Example 3202CI 130256 8-Lead PDIP (300 mil) XXXXXXXX XXXXXNNN YYWW 8-Lead SOIC (3.90 mm) Example 3202-B I/P 3 256 1130 Example 3202-BI SN 3 1130 NNN Legend: XX...X Y YY WW NNN e3 * Note: Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.  1999-2011 Microchip Technology Inc. DS21034F-page 19 MCP3202 Package Marking Information (Continued) 8-Lead TSSOP (4.4 mm) Example 202C 1130 256 Legend: XX...X Y YY WW NNN e3 * Note: DS21034F-page 20 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.  1999-2011 Microchip Technology Inc. MCP3202 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  1999-2011 Microchip Technology Inc. DS21034F-page 21 MCP3202 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS21034F-page 22  1999-2011 Microchip Technology Inc. MCP3202 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  1999-2011 Microchip Technology Inc. DS21034F-page 23 MCP3202           5 '( "'# '6$ +")""' 6&'  '$' ''477+++(  (76 N NOTE 1 E1 1 3 2 D E A2 A L A1 c e eB b1 b 8'" (" ;('" 9#(*  &" 9-:0 9 9 9= ? @ '  ' '  B B   $$6 6""   /  3"' '   B B  #$ '  #$ D$' 0  / /  $$6D$' 0   @ =! ;'  /@ /E  ' ' ;  /  ;$ 6""  @   *  E  *  @  3 B B 8 ;$D$' ; + ;$D$' =!  +, 3- /   !"#$%&'# (! )*#'(#"'* '$+'''$   ,&'- ' "' / (" "$0$  '#$( $&"  ' #" " $&"  ' #" "" '%$1 "$  (" $'   02 3-43"("   '%'!#" ++' #''  "       + -@3 DS21034F-page 24  1999-2011 Microchip Technology Inc. MCP3202 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  1999-2011 Microchip Technology Inc. DS21034F-page 25 MCP3202 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS21034F-page 26  1999-2011 Microchip Technology Inc. MCP3202     !  ""#$%& !'  5 '( "'# '6$ +")""' 6&'  '$' ''477+++(  (76  1999-2011 Microchip Technology Inc. DS21034F-page 27 MCP3202   ()  )" *  !  (+%+(  !  5 '( "'# '6$ +")""' 6&'  '$' ''477+++(  (76 D N E E1 NOTE 1 1 2 b e c A φ A2 A1 L L1 8'" (" ;('" 9#(*  &" ;;0 0 9 9 9= ? @ '  =! :'  B E3B  $$6 6""  @   '$ &&   B   =! D$' 0  $$6D$' 0 / E3  $$6;'   / / 5 ';' ;  E  5 ' ' ;  05 5 '  X B @X ;$ 6""   B  ;$D$' *  B /   !"#$%&'# (! )*#'(#"'* '$+'''$   (" "$0$  '#$( $&"  ' #" " $&"  ' #" "" '%$(( "$ / (" $'   02 3-4 3"("   '%'!#" ++' #''  " 054 & (" )#"#+' #''  )& & (' #  ""        + -@E3 DS21034F-page 28  1999-2011 Microchip Technology Inc. MCP3202 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  1999-2011 Microchip Technology Inc. DS21034F-page 29 MCP3202 APPENDIX A: REVISION HISTORY Revision F (November 2011) Updated Product Identification System Corrected MSOP package marking drawings. Updated Package Specification Drawings with new additions. Revision E (December 2008) Updates to packaging outline drawings. Revision D (December 2006) Updates to packaging outline drawings. Revision C (August 2001) Undocumented changes. Revision B (June 2000) Undocumented changes. Revision A (August 1999) Initial release of this document. DS21034F-page 30  1999-2011 Microchip Technology Inc. MCP3202 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device Device X X /XX Performance Temperature Grade Range Package MCP3202: 12-Bit Serial A/d Converter MCP3202T: 12-Bit Serial A/D Converter (Tape and Reel) (MSOP, SOIC and TSSOP package only) Performance Grade: B C Temperature Range I E Package MS P SN ST = ±1 LSB INL (TSSOP not available) = ±2 LSB INL = -40C to +85C = -40C to +125C = = = = (Industrial) (Extended) Plastic Micro Small Outline (MSOP), 8-Lead Plastic DIP (300 mil Body), 8-Lead Plastic SOIC (150 mil Body), 8-Lead TSSOP (4.4 mm Body), 8-Lead (C Grade only)  1999-2011 Microchip Technology Inc. Examples: a) MCP3202-CI/MS: Industrial temperature, 8LD MSOP package. b) MCP3202-BI/P: B Performance grade, Industrial temperature, 8LD PDIP package c) MCP3202-BI/SN: C Performance grade, Industrial temperature, 8LD SOIC package d) MCP3202T-BI/SN: Tape and Reel, B Performance grade, Industrial temperature., 8LD SOIC package e) MCP3202T-CI/ST: Tape and Reel, C Performance grade, Industrial temperature, 8LD TSSOP package. DS21034F-page 31 MCP3202 NOTES: DS21034F-page 32  1999-2011 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 1999-2011, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-61341-757-7 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified.  1999-2011 Microchip Technology Inc. DS21034F-page 33 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-330-9305 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS21034F-page 34 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 08/02/11  1999-2011 Microchip Technology Inc.