MIC2505/6
Single 2A/Dual 1A High-Side Switches
Features
General Description
• Low MOSFET On-Resistance to 3.0V
- 30 mΩ Typical at 5V (MIC2505 Series)
- 35 mΩ Typical at 3.3V (MIC2505 Series)
- 75 mΩ Typical at 5V (Each MIC2506 Output)
- 80 mΩ Typical at 3.3V (Each MIC2506 Output)
• 3.0V to 7.5V Input
• 110 µA Typical On-State Supply Current
• 1 µA Typical Off-State Supply Current
• Output Can be Forced Higher than Input
(Off-State)
• Current-Limit
• Thermal Shutdown
• 2.5V Undervoltage Lockout (UVLO)
• Open-Load Detection (MIC2505YN/M and
MIC2506YN/M Only)
• Open-Drain Fault Flag
• 5 ms (Slow) Turn-On and Fast Turn-Off
• Logic-Level Control/Enable Input
The MIC2505, MIC2505-1, MIC2505-2, and MIC2506
are single and dual integrated high-side power
switches that consist of TTL-compatible control/enable
inputs, a charge pump, and protected N-channel
MOSFETs. The MIC2505/6 family can be used instead
of separate high-side drivers and MOSFETs in many
low-voltage applications.
Applications
•
•
•
•
•
USB Power Distribution
3.3V and 5V Power Management
PC Card Inrush Limiting Switch
Hot Plug-In Power Supplies
Battery Charger Circuits
The MIC2505/6 family controls voltages ranging from
3.0V to 7.5V. The MIC2505-series can deliver at least
2A continuous current while the MIC2506 can deliver at
least 1A continuous current from each output. A slow
turn-on feature prevents high inrush current when
switching capacitive loads. The internal control circuitry
is powered from the same 3.0V to 7.5V. Within the
device’s input range, outputs can be forced higher than
the input voltage when disabled.
Multipurpose open-drain fault flag outputs indicate
overcurrent limiting, open-load detection (except
MIC2505-1 and -2 versions), thermal shutdown, or
undervoltage lockout for each channel.
Overcurrent limiting is internally fixed and requires no
external components.
Open-load detection is active when the switch is off.
When off, a normal load pulls the output pin low. If the
load is open, an optional, external, high-value resistor
pulls the output pin high, triggering the fault flag.
MIC2505-1 and -2 versions are tailored to Universal
Serial Bus (USB) applications and do not include
open-load detection.
Thermal shutdown turns off the output if the die
temperature exceeds approximately 135°C. If enabled,
the switch automatically restarts when the temperature
falls 10°C.
Undervoltage lockout (UVLO) shuts off the output if the
supply drops below 2.3V typical and re-enables the
output when the supply exceeds 2.5V typical.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
DS20005579B-page 1
MIC2505/6
Package Types
MIC2505/-1/-2
8-Pin SOIC (M)
(Top View)
MIC2506
8-Pin SOIC (M)
(Top View)
MIC2506
MIC2505/-1/-2
CTL
1
8
OUT
CTL A
1
8
OUT A
FLG
2
7
IN
FLG A
2
7
IN
GND
3
6
OUT
FLG B
3
6
GND
GATE
4
5
IN
CTL B
4
5
OUT B
Typical Application Schematics
Single and Dual Switch/Circuit Breakers with Open-Load Detection and Fault Output
2
3
4
CTL
OUT
FLG
IN
GND
GATE
OUT
IN
Optional
Output Delay
Capacitor
DS20005579B-page 2
100Nȍ
8
7
6
5
Optional
Open Load
Detect Resistor
(MIC2505YN or
MIC2505YM
onl\
0.1μF
Pull-up
Resistors
NȍHDFK
A ON
A OFF
FAULT A
FAULT B
B ON
B OFF
MIC2506YM
1
2
3
4
CTL A OUT A
FLG A
FLG B
IN
GND
CTL B OUT B
Nȍ Nȍ
8
7
6
Optional
Open Load
DeteFWResistors
0.1μF
5
Load A
FAULT
MIC2505YM
1
Load
Pull-up
Resistor
Nȍ
ON
OFF
3.0V to 7.5V
Load B
3.0V to 7.5V
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505/6
Functional Block Diagrams
MIC2505 Series Block Diagram
CTL
OSC.
THERMAL
SHUTDOWN
1.2V
REFERENCE
UVLO
CHARGE
PUMP
IN
CURRENT
LIMIT
GATE
CONTROL
Not Included in
MIC2505-1, -2
OPEN LOAD
DETECT
OUT
FLG
MIC2505/2505-1/2505-2
GND
GATE
MIC2506 Block Diagram
FLG A
OPEN LOAD
DETECT
OUT A
CTL A
CHARGE
PUMP
GATE
CONTROL
CURRENT
LIMIT
OSC.
THERMAL
SHUTDOWN
UVLO
1.2V
REFERENCE
CHARGE
PUMP
GATE
CONTROL
IN
CURRENT
LIMIT
CTL B
OPEN LOAD
DETECT
OUT B
FLG B
MIC2506
GND
2016 - 2021 Microchip Technology Inc. and its subsidiaries
DS20005579B-page 3
MIC2505/6
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Supply Voltage (VIN).................................................................................................................................................+8.0V
Fault Flag Voltage (VFLG) .........................................................................................................................................+7.5V
Fault Flag Current (IFLG) .........................................................................................................................................50 mA
Output Voltage (VOUT)................................................................................................................................................7.5V
Output Current (IOUT) .............................................................................................................................Internally Limited
Gate Voltage (VGATE) ........................................................................................................................................ VIN + 15V
Control Input (VCTL) ................................................................................................................................... –0.3V to +15V
Operating Ratings ‡
Supply Voltage (VIN).................................................................................................................................. +3.0V to +7.5V
† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
‡ Notice: The device is not guaranteed to function outside its operating ratings.
DS20005579B-page 4
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505/6
TABLE 1-1:
ELECTRICAL CHARACTERISTICS
Electrical Characteristics: VIN = +5V, GATE = open, TA = 25°C, bold values are valid for –40°C ≤ TA ≤ +85°C,
unless noted. (Note 1).
Parameters
Supply Current
Control Input Voltage
Control Input Current
Control Input Capacitance
Output MOSFET Resistance
Output Turn-On Delay
Output Turn-On Rise Time
Note 1:
2:
3:
Sym.
Min.
Typ.
Max.
Units
Conditions
IDD
—
0.75
5
µA
MIC2505-1, MIC2506, VCTL =
logic 0, OUT = open.
—
110
160
µA
MIC2505-1, MIC2506, VCTL =
logic 1, OUT = open.
—
110
160
µA
MIC2505-2, VCTL = logic 0,
OUT = open.
—
0.75
5
µA
MIC2505-2, VCTL = logic 1,
OUT = open.
—
2.1
2.4
V
VCTL = logic 0 to logic 1
transition
0.8
1.9
—
V
VCTL = logic 1 to logic 0
transition
—
0.01
1
µA
VCTL = logic 0
—
0.01
1
µA
VCTL = logic 1
CCTL
—
1
—
pF
—
RDS(ON)
—
30
50
mΩ
MIC2505 Series, VIN = 5V,
TA = 25°C.
—
—
60
mΩ
MIC2505 Series, VIN = 5V,
–40°C < TA < +85°C.
—
35
60
mΩ
MIC2505 Series, VIN = 3.3V,
TA = 25°C.
—
—
75
mΩ
MIC2505 Series, VIN = 3.3V,
–40°C < TA < +85°C.
—
75
125
mΩ
MIC2506, VIN = 5V,
TA = 25°C.
—
—
150
mΩ
MIC2506, VIN = 5V,
–40°C < TA < +85°C.
—
80
135
mΩ
MIC2506, VIN = 3.3V,
TA = 25°C.
—
—
165
mΩ
MIC2506, VIN = 3.3V,
–40°C < TA < +85°C.
200
850
2000
µs
MIC2505 Series, RL = 10Ω,
CGATE = 0.
100
700
2000
µs
MIC2506, RL = 10Ω each
output.
500
3000
7500
µs
MIC2505 Series, RL = 10Ω,
CGATE = 0.
200
2000
6000
µs
MIC2506, RL = 10Ω each
output.
VCTL
ICTL
tON
tR
Devices are ESD protected; however, handling precautions recommended. All limits guaranteed by testing
or statistical analysis.
MIC2505-1 and -2 versions have no open load detect feature.
Open load threshold is the output voltage (VOUT) where FLG becomes active (low) when CTL is low. OUT
is pulled high by a 100 kΩ external resistor to VIN.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
DS20005579B-page 5
MIC2505/6
TABLE 1-1:
ELECTRICAL CHARACTERISTICS (CONTINUED)
Electrical Characteristics: VIN = +5V, GATE = open, TA = 25°C, bold values are valid for –40°C ≤ TA ≤ +85°C,
unless noted. (Note 1).
Parameters
Output Turn-Off Delay
Output Turn-Off Fall Time
Sym.
Min.
Typ.
Max.
Units
Conditions
tOFF
—
0.7
20
µs
MIC2505 Series, RL = 10Ω,
CGATE = 0.
—
0.8
20
µs
MIC2506, RL = 10Ω each
output.
—
1.5
20
µs
MIC2505 Series, RL = 10Ω,
CGATE = 0.
—
0.7
20
µs
MIC2506, RL = 10Ω each
output.
tF
Output Leakage Current
ILKG
—
—
10
µA
—
Current Limit Threshold
ILIM
2
4
—
A
MIC2505 Series
1
2
3
A
MIC2506
VOPENL_TH
0.5
1
1.5
V
VCTL = logic low, Note 3
Overtemperature Shutdown
Threshold
TSD
—
135
—
°C
TJ increasing
—
125
—
°C
TJ decreasing
Error Flag Output Resistance
RFLG
—
10
25
Ω
VIN = 5V, IL = 10 mA
—
15
40
Ω
VIN = 3.3V, IL = 10 mA
Open Load Threshold (Note 2)
Error Flag Off Current
IFLG_OFF
—
0.01
1
µA
VFLAG = 5V
UVLO Threshold
VUVLO_TH
2.2
2.5
3.0
V
VIN increasing
UVLO Hysteresis
VUVLO_TH_
—
215
—
mV
MIC2505
HYST
—
235
—
mV
MIC2506
Note 1:
2:
3:
Devices are ESD protected; however, handling precautions recommended. All limits guaranteed by testing
or statistical analysis.
MIC2505-1 and -2 versions have no open load detect feature.
Open load threshold is the output voltage (VOUT) where FLG becomes active (low) when CTL is low. OUT
is pulled high by a 100 kΩ external resistor to VIN.
DS20005579B-page 6
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505/6
TEMPERATURE SPECIFICATIONS
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Ambient Operating Temperature
TA
–40
—
+85
°C
Storage Temperature Range
TS
–65
—
+150
°C
—
Lead Temperature
—
—
—
+260
°C
Soldering, 5s
JA
—
160
—
°C/W
Temperature Ranges
—
Package Thermal Resistances
Thermal Resistance, SOIC
2016 - 2021 Microchip Technology Inc. and its subsidiaries
—
DS20005579B-page 7
MIC2505/6
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
CONTROL (V)
Note:
TYPICAL PERFORMANCE CURVES
10
CONTROL (V)
2.0
5
0
10
5
0
6
-5
OUTPUT (V)
OUTPUT (V)
-5
6
4
2
RL = 5Ω
(IL = 1A)
0
-2
-2
0 2 4
TIME (ms)
FIGURE 2-1:
Characteristics.
6
-2
0
2
TIME (μs)
MIC2505 Turn-On, Turn-Off
FIGURE 2-4:
Characteristics.
THRESHOLD VOLTAGE (V)
OUTPUT RESISTANCE (mΩ)
0
RL = 5Ω
(IL = 1A)
0 2 4
TIME (ms)
-1
6
0
1
TIME (μs)
2
MIC2506 Turn-On, Turn-Off
3.0
MIC2506
80
60
MIC2505
40
20
2
FIGURE 2-2:
Supply Voltage.
3
4
5
6
7
SUPPLY VOLTAGE (V)
Output On Resistance vs.
2.5
VIN FALLING
2.0
FIGURE 2-5:
Temperature.
60
MIC2505
40
20
ERROR FLAG VOLTAGE (mV)
80
FLG = ACTIVE
300
VDD = 3.3V
200
100
0
-40 -20 0 20 40 60 80 100
TEMPERATURE (°C)
DS20005579B-page 8
UVLO Threshold Voltage vs.
400
MIC2506
FIGURE 2-3:
Temperature.
VIN RISING
1.5
-40 -20 0 20 40 60 80 100
TEMPERATURE (°C)
8
100
ON RESISTANCE (mΩ)
2
-2
-2
4
100
0
4
Output On Resistance vs.
VDD = 5V
0
0.1
1
10
100
ERROR FLAG CURRENT (mA)
FIGURE 2-6:
Flag Current.
Error Flag Voltage vs. Error
2016 - 2021 Microchip Technology Inc. and its subsidiaries
200
180
SUPPLY CURRENT (μA)
SUPPLY CURRENT (μA)
MIC2505/6
160
140
120
100
80
60
40
20
0
2
FIGURE 2-7:
Supply Voltage.
3
4
5
6
7
SUPPLY VOLTAGE (V)
200
180
160
140
120
100
FIGURE 2-10:
Temperature.
SUPPLY CURRENT (μA)
SUPPLY CURRENT (μA)
1.5
1.0
0.5
2
FIGURE 2-8:
Supply Voltage.
3
4
5
6
7
SUPPLY VOLTAGE (V)
Off-State Supply Current vs.
1.0
0.5
FIGURE 2-11:
Temperature.
Off-State Supply Current vs.
2.5
2.0
THRESHOLD VOLTAGE (V)
THRESHOLD VOLTAGE (V)
1.5
0
-40 -20 0 20 40 60 80 100
TEMPERATURE (°C)
8
2.5
VCTL RISING
1.5
1.0
On-State Supply Current vs.
2.0
2.0
0
40
20
0
-40 -20 0 20 40 60 80 100
TEMPERATURE (°C)
8
On-State Supply Current vs.
80
60
VCTL FALLING
2
FIGURE 2-9:
Supply Voltage.
3
4
SUPPLY VOLTAGE (V)
5
Control Threshold vs.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
2.0
1.5
VCTL RISING
VCTL FALLING
1
-40 -20 0 20 40 60 80 100
TEMPERATURE (°C)
FIGURE 2-12:
Temperature.
Control Threshold vs.
DS20005579B-page 9
MIC2505/6
TURN-ON DELAY (ms)
1000
800
600
400
200
0
0
50
100 150 200
CAPACITANCE (nF)
250
FIGURE 2-13:
MIC2505 Turn-On Delay
with External Gate Capacitance.
3.0
TEST CIRCUITS
+5V
10kΩ
VFLG
+5V
MIC2505/-1/-2
10kΩ
10kΩ
MIC2506YM
CTL
OUT
FLG
IN
VFLG A
FLG A
IN
GND
OUT
VFLG B
FLG B
GND
GATE
FIGURE 3-1:
DS20005579B-page 10
IN
A ON
A OFF
10Ω
CTL A OUT A
1μF
1μF
10Ω
MIC2505 Series Test Circuit.
B ON
B OFF
FIGURE 3-2:
10Ω
CTL B OUT B
MIC2506 Test Circuit.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505/6
4.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 4-1.
TABLE 4-1:
PIN FUNCTION TABLE
Pin Number
MIC2505 Series
Pin Number
MIC2506
1
1, 4
CTL (A/B) Control (Input): TTL-compatible control input. MIC2505,
MIC2505-1, and MIC2506 are active-high. MIC2505-2 is active-low.
2
2, 3
FLG (A/B) Fault Flag (Output): Active-low, open-drain output. If CTL is low,
indicates open load. If CTL is high, indicates current limit, thermal
shutdown, or UVLO.
MIC2505-1 and -2 do not support open-load detect.
3
6
GND
Ground: Return.
4
—
GATE
Output MOSFET Gate: Open for fastest rise time. Connect
capacitor to ground to slow rise time. (See Figure 2-13)
5, 7
7
IN
6, 8
8, 5
Pin Name
Description
Supply Input: Output MOSFET drain. Also supplies IC’s internal
circuitry. Connect to supply.
MIC2505 series only: Pins 5 and 7 must be externally connected
together.
OUT (A/B) Switch Output: Output MOSFET source. Typically connect to
switched side of load. Output voltage can be pulled above input
voltage in off mode.
MIC2505 series only: Pins 6 and 8 must be externally connected
together.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
DS20005579B-page 11
MIC2505/6
5.0
FUNCTIONAL DESCRIPTION
The MIC2505-series and MIC2506 are high-side
N-Channel switches. The MIC2505, MIC2505-1, and
MIC2506 have active-high enable inputs. The
MIC2505-2 has an active-low input. Fault conditions
inhibit output transistor turn-on or turn-off when
enabled.
5.1
Control Input
CTL (control input) activates the oscillator, thermal
shutdown, UVLO, 1.2V reference, and gate control
circuits. If there are no fault conditions, the output
MOSFET turns on when enabled.
5.2
Reference
A 1.2V bandgap reference supplies a regulated voltage
to the thermal shutdown and undervoltage lockout
circuits. The reference is only active when CTL is
enabled.
5.3
Oscillator/Charge Pump
The oscillator produces an 80 kHz square wave output
that drives the charge pump. The oscillator is enabled
when CTL is active.
The charge pump is a voltage quintupler (5x). The
charge pump capacitors are self contained.
5.4
Gate Control
The gate control circuit charges the output MOSFET
gate from the charge pump output or discharges the
MOSFET gate to ground as determined by CTL,
thermal shutdown, or undervoltage lockout (UVLO).
method for optimum turn-on threshold has the source
connected to the body. This would allow a large current
to flow when VSOURCE > VDRAIN + 0.6V.
5.5.1
MIC2505 SERIES ONLY
Duplicate IN and OUT leads are not internally
connected. Connect both IN pins to the supply.
Connect both OUT leads to the load.
5.6
Thermal Shutdown
Thermal shutdown shuts off the output MOSFET and
signals the fault flag if the die temperature exceeds
135°C. 10°C of hysteresis prevents the switch from
turning on until the die temperature drops to 125°C.
Overtemperature detection functions only when the
control input is enabled (output MOSFET is on). Both
MIC2506 outputs are shut off during overtemperature,
and both flags will go low.
5.7
Undervoltage Lockout
UVLO (undervoltage lockout) prevents the output
MOSFET from turning on until VIN (input voltage)
exceeds 2.5V typical. After the switch turns on, if VIN
drops below 2.3V typical, UVLO shuts off the output
MOSFET and turns the fault flag on (active-low) until
VIN drops below 1.5V.
Undervoltage detection functions only when the control
input is enabled (output MOSFET is on).
5.8
Overcurrent Limit
The overcurrent limit is preset internally. The preset
level prevents damage to the output MOSFET, but
allows a minimum current of 2A through the output
MOSFET of the MIC2505-series and 1A for each
output MOSFET of the MIC2506. Output current is
monitored by sensing the voltage drop across the
output MOSFET drain metal resistance.
An optional, external capacitor may be connected to
the MIC2505 GATE to lengthen the rise time. This
slows the turn on of the MOSFET output switch. (See
Figure 2-13) Because this pin connects directly to the
MOSFET gate, use ESD precautions when contacting
components connected to this pin. Leakage resistance
may increase turn on times.
Overcurrent detection functions only when the control
input is enabled (output MOSFET is on) and VIN is
above the UVLO threshold.
5.5
5.9
Input and Output
IN (input) is the supply connection to the logic circuitry
and the drain of the output MOSFET. OUT (output) is
the source of the output MOSFET. In a typical circuit,
current flows through the switch from IN to OUT toward
the load.
Open-Load Detection
Open-load detection is available only on the MIC2505
and MIC2506. The open-load detection feature is not
included in the MIC2505-1 or -2 versions.
The output MOSFET and driver circuitry are also
designed to allow the MOSFET source to be externally
forced to a higher voltage than the drain (VOUT > VIN)
when the output switch is off and VIN > UVLO minimum.
In this situation, the MIC2505/6 avoids undesirable
drain to body diode reverse current flow by grounding
the body when the switch is off. The conventional
Open-load detection indicates the absence of an output
load by activating the fault flag. Open-load detection is
optional and is enabled by connecting a high-value
pull-up resistor between IN and OUT. If there is no load,
the circuit detects a high OUT (output) voltage (typically
≥1V) and signals the fault flag. Under normal
conditions, the low resistance of a typical load pulls
OUT low. Open-load detection functions only when the
control input is low (output MOSFET is off).
DS20005579B-page 12
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505/6
5.10
Fault Flag
FLG is an N-channel, open-drain MOSFET output. The
fault flag is active (low) for one or more of the following
conditions: open load (except MIC2505-1 and -2
versions), undervoltage, current limit, or thermal
shutdown. The flag output MOSFET is capable of
sinking a 10 mA load to typically 100 mV above
ground.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
DS20005579B-page 13
MIC2505/6
6.0
APPLICATION INFORMATION
6.1
Supply Filtering
A 0.1 μF to 1 μF bypass capacitor from IN to GND,
located at the device is strongly recommended to
control supply transients. Without a bypass capacitor,
an output short may cause sufficient ringing on the
input (from supply lead inductance) to destroy the
internal control circuitry.
Input transients must not exceed the absolute
maximum supply voltage (VIN(MAX) = 7.5V) even for a
short duration.
6.4
Power Bus Switch
The MIC2505/6 family features a MOSFET reverse
current flow prevention circuit. This prevents current
from flowing backwards (from OUT to IN) when CTL is
disabled as long as VIN is above UVLO minimum. In
Figure 6-2, when U1 is on and U2 is off, this feature
prevents current flow from the load (5V) backward
through U2 to the 3.3V supply. If a discrete MOSFET
and driver were used, the MOSFET’s internal body
diode would short the 5V load to the 3.3V supply.
FLG will be active (low) on any switch that is off
whenever the load voltage is greater than the open
load threshold (approximately 1V) except for
MIC2505-1 and MIC2505-2.
3.0V to 7.5V
MIC2505YM
ON
OFF
1
2
3
4
CTL
OUT
FLG
IN
GND
GATE
OUT
IN
1N4148
(optional)
6
0.1μF to 1μF
1
2
5
3
6.2
Control Input
CTL must be driven logic high or logic low, or be pulled
high or low for a clearly defined input. Floating the input
may cause unpredictable operation. Add a diode clamp
if negative spikes may occur. See Figure 6-2.
6.3
Open-Load Detection
Refer to the Typical Application Schematics.
Open-load detection is available only on the MIC2505
and MIC2506. For USB power distribution applications,
the open-load detection feature is not included in the
MIC2505-1 or -2 versions.
The optional open-load detection resistor supplies a
small pull-up current to the load when the output switch
is off. A 100 kΩ resistor will draw 50 μA from a 5V
supply. Normally, the load dominates, pulling OUT low.
If the load is absent, the optional resistor pulls OUT
high, activating the fault flag if CTL is off.
When a load is switched off with CTL, capacitance on
the output may cause the open-load function to pull the
flag low until the capacitor is discharged below
approximately 2.4V.
Omit the pull-up resistor when open load detection is
not required and for minimum off-state supply current.
DS20005579B-page 14
CTL
OUT
IN
FLG
GND
OUT
GATE
IN
U2
MIC2505YM
8
1
7
2
6
3
5
4
0.1μF
CTL
OUT
FLG
IN
GND
OUT
GATE
IN
8
7
6
5
0.1μF
Load
Supply Bypassing.
The bypass capacitor may be omitted only if board
design precautions are followed, such as using
extremely short supply leads or power and ground
planes.
+3.3V
U1
MIC2505YM
7
4
FIGURE 6-1:
+5V
Logic-High = 5V Output
Logic-Low = 3.3V Output
8
FIGURE 6-2:
5V/3.3V Switch Concept.
This circuit’s function would otherwise require a dual
driver, two MOSFETs, plus two diodes (or a dual driver
plus four MOSFETs).
6.5
Hot Plug-In Applications
(Soft-Start)
The MIC2505/6 family can be used to protect the
socket-side and card-side of a supply circuit from
transients caused when a capacitive load is connected
to an active supply.
The switch presents a high impedance when off, and
slowly becomes a low impedance as it turns on. This
reduces the inrush current and related voltage drop
that result from charging a capacitive load.
3.3V
1
2
3
4
GND
Socket
FIGURE 6-3:
Power Control
Circuitry
MIC2505YM
CTL
OUT
FLG
IN
GND
OUT
GATE
IN
8
7
Capacitive
Load
6
5
0.1μF
Card
Hot Pulg-In Concept.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505/6
A gate capacitor may be added to the MIC2505 to slow
the turn on time even more, reducing the inrush
current. See Figure 2-13. The UVLO feature ensures
that each time the card is removed and VIN = 0 that the
gate of the output switch is discharged to zero volts. A
controlled turn-on is executed each time a board is
plugged in, even with multiple insertions.
6.6
USB Application
Figure 6-4 depicts a low cost and robust
implementation of a four-port, self-powered USB hub
circuit employing ganged overcurrent protection.
(+)
4.45V to 5.25V
3.5A max.
(–)
VBUS
D+
Ferrite
Bead
IN
D–
GND
100k
33μF MIC5203-3.3
MIC5207-3.3
LDO Regulator
D+
3.3V USB Controller
V+
OUT
GND
VBUS
1.0
μF
ON/OFF
OVERCURRENT
4.7
μF
MIC2505-2/-1
EN
IN
GND
OUT
GND
D–
GND
Downstream
USB
Port 1
500mA max.
VBUS
IN
D+
0.1μF
D+
D–
33μF
OUT
FLG
GATE
0.01μF
0.01μF
33μF
D–
GND
Bold lines indicate
0.1" wide, 1-oz. copper
high-current traces.
Downstream
USB
Port 2
500mA max.
VBUS
D+
0.01μF
33μF
D–
GND
Downstream
USB
Port 3
500mA max.
VBUS
D+
0.01μF
33μF
D–
GND
Downstream
USB
Port 4
500mA max.
Data
FIGURE 6-4:
Ganged-Switch Self-Powered Hub.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
DS20005579B-page 15
MIC2505/6
7.0
PACKAGING INFORMATION
7.1
Package Marking Information
8-Lead SOIC*
for MIC2505
Example
MIC
XXXXXX
WNNN
MIC
2505YM
6914
for MIC2505-1/-2
Example
XXXX
-XXX
2505
-1YM
WNNN
0552
for MIC2506
Example
MIC
XXXXXX
WNNN
Legend: XX...X
Y
YY
WW
NNN
e3
*
MIC
2506YM
8427
Product code or customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle
mark).
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information. Package may or may not include
the corporate logo.
Underbar (_) symbol may not be to scale.
DS20005579B-page 16
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505/6
8-Lead SOIC Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2016 - 2021 Microchip Technology Inc. and its subsidiaries
DS20005579B-page 17
MIC2505/6
NOTES:
DS20005579B-page 18
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505/6
APPENDIX A:
REVISION HISTORY
Revision A (August 2016)
• Converted Micrel document MIC2505/6 to Microchip data sheet DS20005579A.
• Minor text changes throughout.
Revision B (September 2021)
• Updated the Package Marking Information drawing.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
DS20005579B-page 19
MIC2505/6
NOTES:
DS20005579B-page 20
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505/6
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office.
–
PART NO.
X
X
X
–
X
Examples:
a) MIC2505YM:
Single 2A High-Side Switch, ActiveHigh with Open-Load Detect,
–40°C to +85°C Temp. Range,
8-Pin SOIC, 95/Tube
b) MIC2505YM-TR:
Single 2A High-Side Switch, ActiveHigh with Open-Load Detect,
–40°C to +85°C Temp. Range,
8-Pin SOIC, 2,500/Reel
c) MIC2505-1YM:
Single 2A High-Side Switch, ActiveHigh without Open-Load Detect,
–40°C to +85°C Temp. Range,
8-Pin SOIC, 95/Tube
d) MIC2505-1YM-TR:
Single 2A High-Side Switch, ActiveHigh without Open-Load Detect,
–40°C to +85°C Temp. Range,
8-Pin SOIC, 2,500/Reel
e) MIC2505-2YM:
Single 2A High-Side Switch, ActiveLow without Open-Load Detect,
–40°C to +85°C Temp. Range,
8-Pin SOIC, 95/Tube
f)
Single 2A High-Side Switch, ActiveLow without Open-Load Detect,
–40°C to +85°C Temp. Range,
8-Pin SOIC, 2,500/Reel
Device
Control/ Temperature Package Media Type
Enable and
Open-Load Detect
Device:
MIC2505:
MIC2506:
Control/Enable
and Open-Load
Detect:
Blank
1
2
Temperature:
Y
=
–40°C to +85°C
Package:
M
=
8-Pin SOIC
Media Type:
TR =
none =
2,500/Reel
95/Tube
Note 1:
=
=
=
Single 2A High-Side Switch
Dual 1A High-Side Switch, (Note 1)
Active-High with Open-Load Detect
Active-High without Open-Load Detect
Active-Low without Open-Load Detect
MIC2506 is only available in an Active-High with Open-Load
Detect configuration.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
MIC2505-2YM-TR:
g) MIC2506YM:
Dual 1A High-Side Switch, ActiveHigh with Open-Load Detect,
–40°C to +85°C Temp. Range,
8-Pin SOIC, 95/Tube
h) MIC2506YM-TR:
Dual 1A High-Side Switch, ActiveHigh with Open-Load Detect,
–40°C to +85°C Temp. Range,
8-Pin SOIC, 2,500/Reel
DS20005579B-page 21
MIC2505/6
NOTES:
DS20005579B-page 22
2016 - 2021 Microchip Technology Inc. and its subsidiaries
Note the following details of the code protection feature on Microchip products:
•
Microchip products meet the specifications contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and
under normal conditions.
•
Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of
Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not
mean that we are guaranteeing the product is “unbreakable”. Code protection is constantly evolving. Microchip is committed to
continuously improving the code protection features of our products.
This publication and the information herein may be used only
with Microchip products, including to design, test, and integrate
Microchip products with your application. Use of this information in any other manner violates these terms. Information
regarding device applications is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your
specifications. Contact your local Microchip sales office for
additional support or, obtain additional support at https://
www.microchip.com/en-us/support/design-help/client-supportservices.
THIS INFORMATION IS PROVIDED BY MICROCHIP "AS IS".
MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED,
WRITTEN OR ORAL, STATUTORY OR OTHERWISE,
RELATED TO THE INFORMATION INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A
PARTICULAR PURPOSE, OR WARRANTIES RELATED TO
ITS CONDITION, QUALITY, OR PERFORMANCE.
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY
KIND WHATSOEVER RELATED TO THE INFORMATION OR
ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS
BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES
ARE FORESEEABLE. TO THE FULLEST EXTENT
ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON
ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION
OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF
ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP
FOR THE INFORMATION.
Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to
defend, indemnify and hold harmless Microchip from any and
all damages, claims, suits, or expenses resulting from such
use. No licenses are conveyed, implicitly or otherwise, under
any Microchip intellectual property rights unless otherwise
stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec,
AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud,
CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO,
JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus,
maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo,
MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower,
PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch,
SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash,
Symmetricom, SyncServer, Tachyon, TimeSource, tinyAVR, UNI/O,
Vectron, and XMEGA are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
AgileSwitch, APT, ClockWorks, The Embedded Control Solutions
Company, EtherSynch, Flashtec, Hyper Speed Control, HyperLight
Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3,
Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, QuietWire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub,
TimePictra, TimeProvider, TrueTime, WinPath, and ZL are
registered trademarks of Microchip Technology Incorporated in the
U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky,
BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive,
CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net,
Dynamic Average Matching, DAM, ECAN, Espresso T1S,
EtherGREEN, GridTime, IdealBridge, In-Circuit Serial
Programming, ICSP, INICnet, Intelligent Paralleling, Inter-Chip
Connectivity, JitterBlocker, Knob-on-Display, maxCrypto, maxView,
memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo,
MPLIB, MPLINK, MultiTRAK, NetDetach, NVM Express, NVMe,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple
Blocker, RTAX, RTG4, SAM-ICE, Serial Quad I/O, simpleMAP,
SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI,
SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total
Endurance, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY,
ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks
of Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage
Technology, Symmcom, and Trusted Time are registered
trademarks of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany
II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in
other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2016 - 2021, Microchip Technology Incorporated and its subsidiaries.
All Rights Reserved.
For information regarding Microchip’s Quality Management Systems,
please visit www.microchip.com/quality.
2016 - 2021 Microchip Technology Inc. and its subsidiaries
ISBN: 978-1-5224-8985-6
DS20005579B-page 23
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
DS20005579B-page 24
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Denmark - Copenhagen
Tel: 45-4485-5910
Fax: 45-4485-2829
Finland - Espoo
Tel: 358-9-4520-820
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-72400
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7288-4388
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
2016 - 2021 Microchip Technology Inc. and its subsidiaries
09/14/21
工商网监
湘ICP备2023018690号
