MIC5202
Dual 100 mA Low-Dropout Regulator
Features
General Description
•
•
•
•
•
•
•
•
•
•
•
•
The MIC5202 is a dual linear voltage regulator with low
dropout voltage (typically 17 mV at light loads and
210 mV at 100 mA), and low ground current (1 mA at
100 mA per output). Ideal for battery-operated
applications, the MIC5202 offers 1% output voltage
accuracy and dual enable pins. The enable pins may
be driven individually or tied directly to VIN. When the
part is disabled, power consumption drops to nearly
zero. The MIC5202 ground current increases slightly in
dropout, which minimizes power consumption and
increases battery life. Some key features include
reversed battery protection, current-limit, and
overtemperature protection.
High Output Voltage Accuracy
Variety of Output Voltages
Up to 100 mA of Continuous Output Current
Low Ground Current
Low Dropout Voltage
Excellent Line and Load Regulations
Extremely Low Temperature Coefficient
Current and Thermal Limit Protections
Reverse-Battery Protection
Zero-Off Mode Current
Logic-Controlled Electronic Shutdown
8-Lead SOIC Package
The MIC5202 is available in fixed output voltages in a
small 8-lead SOIC package.
Applications
•
•
•
•
•
•
•
Cell Phones
Laptop, Notebook, and Palmtop Computers
Battery-Powered Equipment
PCMCIA VCC and VPP Regulation/Switching
Barcode Scanners
SMPS Post-Regulator/DC-to-DC Modules
High-Efficiency Linear Power Supplies
Typical Application Schematic
MIC5202
8-LEAD SOIC
U1
MIC5202
VOUT1
VOUT2
VOUT1
VIN1
GND1
EN1
VOUT2
VIN2
GND2
EN2
2016 - 2022 Microchip Technology Inc. and its subsidiaries
EN1
EN2
DS20005614B-page 1
MIC5202
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Input Supply Voltage (VIN1, VIN2) ................................................................................................................ –20V to +60V
Enable Input Voltage (EN1, EN2)................................................................................................................ –20V to +60V
ESD Rating (Note 1)................................................................................................................................... ESD Sensitive
Operating Ratings ‡
Input Supply Voltage (VIN1, VIN2) ............................................................................................................... +2.5V to +26V
Enable Input Voltage (EN1, EN2)....................................................................................................................... 0V to VIN
† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
‡ Notice: The device is not guaranteed to function outside its operating ratings.
Note 1: Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5 kΩ in series with
100 pF.
DS20005614B-page 2
2016 - 2022 Microchip Technology Inc. and its subsidiaries
MIC5202
ELECTRICAL CHARACTERISTICS
Electrical Characteristics: VIN = VOUT + 1V, COUT = 10 µF; IOUT = 1 mA; TJ = 25°C, bold values indicate –40°C ≤
TJ ≤ +125°C; unless noted. Specifications are for one LDO. (Note 1).
Parameters
Sym.
Min.
Typ.
Max.
Output Voltage Accuracy
VOUT
–1
—
1
–2
—
2
ΔVOUT/ΔT
—
40
150
Line Regulation
ΔVOUT/
VOUT
—
0.004
0.10
—
—
0.40
Load Regulation (Note 3)
ΔVOUT/
VOUT
—
0.04
0.16
—
—
0.30
—
17
—
IOUT = 100 µA
—
130
—
IOUT = 20 mA
—
150
—
—
180
—
IOUT = 50 mA
—
225
350
IOUT = 100 mA
—
0.01
—
—
170
—
VEN ≥ 2.0V, IOUT = 100 µA
—
270
—
IOUT = 20 mA
—
330
—
—
500
—
IOUT = 50 mA
—
1200
1500
IOUT = 100 mA
Output Voltage Temperature
Coefficient (Note 2)
Dropout Voltage (Note 4)
Ground Pin Current Shutdown
Ground Pin Current (Note 5)
VIN –
VOUT
ISHUTDOWN
IGND
Units
%
Conditions
—
ppm/°C —
%
VIN = VOUT + 1V to 26V
%
IOUT = 0.1 mA to 100 mA
mV
µA
µA
IOUT = 30 mA
VEN ≤ 0.7V (shutdown)
IOUT = 30 mA
Ground Pin Current in Dropout
IGNDDO
—
270
330
µA
VIN = 0.5V less than VOUT,
IOUT = 100 µA
Power Supply Rejection Ratio
PSRR
—
75
—
dB
—
Short Circuit Current Limit
ILIMIT
—
280
—
mA
VOUT = 0V
ΔVOUT/
ΔPD
—
0.05
—
%/W
—
en
—
100
—
µV
—
Thermal Regulation (Note 6)
Output Noise
Note 1:
2:
3:
4:
5:
6:
Specification for packaged product only.
Output voltage temperature coefficient is defined as the worst case voltage change divided by the temperature range.
Load regulation is measured at a constant junction temperature using low duty cycle pulse testing. Parts
are tested for load regulation in the load range from 0.1 mA to 100 mA. Changes in output voltage caused
by heating effects are covered by the thermal regulation specification.
Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its
nominal value measured at 1V differential.
Ground pin current is the regulator quiescent current plus pass transistor base current. The total current
drawn from the supply is the sum of the load current plus the ground pin current.
Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 100 mA load pulse at
VIN = 26V for t = 10 ms.
2016 - 2022 Microchip Technology Inc. and its subsidiaries
DS20005614B-page 3
MIC5202
ELECTRICAL CHARACTERISTICS (CONTINUED)
Electrical Characteristics: VIN = VOUT + 1V, COUT = 10 µF; IOUT = 1 mA; TJ = 25°C, bold values indicate –40°C ≤
TJ ≤ +125°C; unless noted. Specifications are for one LDO. (Note 1).
Parameters
Sym.
Min.
Typ.
Max.
—
—
0.7
2.0
—
—
IENL
—
0.01
—
IENH
—
8
50
Units
Conditions
Enable Input
Enable Input Voltage
Enable Input Current
Note 1:
2:
3:
4:
5:
6:
VEN
V
µA
Logic-Low = Off
Logic-High = On
VEN ≤ 0.7V
VEN ≥ 2.0V
Specification for packaged product only.
Output voltage temperature coefficient is defined as the worst case voltage change divided by the temperature range.
Load regulation is measured at a constant junction temperature using low duty cycle pulse testing. Parts
are tested for load regulation in the load range from 0.1 mA to 100 mA. Changes in output voltage caused
by heating effects are covered by the thermal regulation specification.
Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its
nominal value measured at 1V differential.
Ground pin current is the regulator quiescent current plus pass transistor base current. The total current
drawn from the supply is the sum of the load current plus the ground pin current.
Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 100 mA load pulse at
VIN = 26V for t = 10 ms.
TEMPERATURE SPECIFICATIONS
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Junction Operating Temperature
Range
TJ
–40
—
+125
°C
Note 1
Storage Temperature
TS
–65
—
+150
°C
—
Lead Temperature
—
—
—
+260
°C
Soldering, 10s
JA
—
63
—
°C/W
Temperature Ranges
Package Thermal Resistances
Thermal Resistance, SOIC 8-Ld
Note 1:
—
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, JA). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
DS20005614B-page 4
2016 - 2022 Microchip Technology Inc. and its subsidiaries
MIC5202
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
10
GROUND CURRENT (mA)
DROPOUT VOLTAGE (mV)
250
200
150
100
50
0
0.01
0.1
1
10
100
1
0.1
0.01
1000
OUTPUT CURRENT (mA)
FIGURE 2-1:
Current.
Dropout Voltage vs. Output
FIGURE 2-4:
Current.
1
10
100
Ground Current vs. Output
1.6
0.3
GROUND CURRENT (mA)
DROPOUT VOLTAGE (V)
0.4
IOUT = 100mA
0.2
0.1
IOUT = 1mA
1.4
1.2
IOUT = 100mA
1.0
0.8
0.6
0.4
IOUT = 1mA
0.2
0.0
0
-60
0
-30
30
60
120
90
0
150
TEMPERATURE (ºC)
FIGURE 2-2:
Temperature.
Dropout Voltage vs.
4
8
6
10
FIGURE 2-5:
Voltage.
Ground Current vs. Input
3.5
OUTPUT VOLTAGE (V)
3.0
IOUT = 100mA
2.5
2.0
1.5
1.0
IOUT = 100μA, 1mA
3.0
2.5
CIN = 2.2μF
COUT = 4.7μF
2.0
1.5
1.0
0.5
0.5
0.0
0.0
0
2
4
6
8
10
0
Dropout Characteristics.
2016 - 2022 Microchip Technology Inc. and its subsidiaries
0.1
0.2
0.3
OUTPUT CURRENT (A)
INPUT VOLTAGE (V)
FIGURE 2-3:
2
INPUT VOLTAGE (V)
3.5
OUTPUT VOLTAGE (V)
0.1
OUTPUT CURRENT (mA)
FIGURE 2-6:
Current.
Output Voltage vs. Output
DS20005614B-page 5
MIC5202
3.6
CIN = 2.2μF
IOUT = 100μA
OUTPUT VOLTAGE (V)
GROUND CURRENT (mA)
0.30
CIN = 2.2μF
COUT = 4.7μF
0.25
0.20
0.15
-60
-30
0
30
60
90
120
3.5
3.4
3.3
3.2
3 DEVICES:
HI/AVG/LO
3.1
CURVES APPLICABLE
AT 100μA AND 100mA
3.0
-60
150
COUT = 4.7μF
-30
TEMPERATURE (ºC)
FIGURE 2-7:
Temperature.
30
60
90
120
150
FIGURE 2-10:
Output Voltage vs.
Temperature (3.3V Version).
Ground Current vs.
1.5
300
OUTPUT CURRENT (mA)
GROUND CURRENT (mA)
0
TEMPERATURE (ºC)
IOUT = 100mA
1.4
CIN = 2.2μF
COUT = 4.7μF
1.3
1.2
1.1
280
260
240
220
VOUT = 3.3V
200
180
VOUT = 0V
(SHORT CIRCUIT)
160
140
120
1.0
-50
50
0
100
TEMPERATURE (ºC)
-30
0
30
60
90
120
150
TEMPERATURE (ºC)
FIGURE 2-11:
Temperature.
Ground Current vs.
Output Current vs.
3.30
100
MINIMUM INPUT VOLTAGE (V)
OUTPUT
CURRENT (mA)
¨OUTPUT (mV)
FIGURE 2-8:
Temperature.
100
-60
150
50
0
COUT = 4.7μF
100
0
0
5
10
15
20
25
30
35
TIME (ms)
FIGURE 2-9:
Version).
DS20005614B-page 6
Thermal Regulation (3.3V
3.29
3.28
CIN = 2.2μF
3.27
COUT = 4.7μF
3.26
IOUT = 1mA
3.25
3.24
3.23
3.22
3.21
3.20
-60
-30
0
30
60
90
120
150
TEMPERATURE (ºC)
FIGURE 2-12:
Temperature.
Minimum Input Voltage vs.
2016 - 2022 Microchip Technology Inc. and its subsidiaries
300
120
250
100
INPUT CURRENT (mA)
SHORT CIRCUIT CURRENT (mA)
MIC5202
200
150
100
CIN = 2.2μF
50
VOUT = 3.3V
COUT = 4.7μF
80
60
40
ROUT = 33
20
0
0
1
2
3
5
4
6
0
7
1
2
Short Circuit Current vs.
¨OUTPUT (mV)
20
10
0
-10
COUT = 4.7μF
-20
200
100
7
8
9
10
10
COUT = 1μF
5
IOUT = 1mA
0
-5
6
4
2
4
8
6
10
0
0.2
TIME (ms)
FIGURE 2-14:
FIGURE 2-17:
Load Transient.
¨OUTPUT (mV)
20
10
0
-10
COUT = 47μF
-20
0.4
0.6
0.8
TIME (ms)
INPUT
VLOTAGE (V)
¨OUTPUT (mV)
6
0
0
OUTPUT
CURRENT (mA)
5
4
FIGURE 2-16:
Input Current vs. Input
Voltage (3.3V Version).
INPUT
VLOTAGE (V)
OUTPUT
CURRENT (mA)
¨OUTPUT (mV)
FIGURE 2-13:
Input Voltage.
3
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
200
100
Line Transient.
15
10
COUT = 10μF
5
IOUT = 1mA
0
6
4
0
0
10
20
30
40
0
TIME (ms)
FIGURE 2-15:
Load Transient.
2016 - 2022 Microchip Technology Inc. and its subsidiaries
0.1
0.2
0.3
0.4
0.5
0.6
TIME (ms)
FIGURE 2-18:
Line Transient.
DS20005614B-page 7
MIC5202
1000
0.1
1
2
3
4
5
6
7
FREQUENCY (Hz)
INPUT VOLTAGE (V)
FIGURE 2-19:
Input Current vs. Input
Voltage (3.3V Version).
FIGURE 2-22:
ENABLE CURRENT (μA)
OUTPUT (V)
ENABLE (V)
4
3
2
COUT = 4.7μF
1
IOUT = 1mA
0
2
0
CIN = 2.2μF
30
COUT = 4.7μF
25
20
15
VEN = 5V
10
5
VEN = 2V
0
0
50
100
150
200
250
FIGURE 2-20:
Version).
-5
-60
300
TIME (μs)
Enable Transient (3.3V
-30
FIGURE 2-23:
vs. Temperature.
0
30
60
90
120
150
TEMPERATURE (ºC)
Enable Current Threshold
1.6
5
4
ENABLE VOLTAGE (V)
OUTPUT (V)
Output Impedance.
35
5
ENABLE (V)
1×106
0.001
0
0
IOUT = 100mA
0.01
100×103
10
IOUT = 1mA
1
10×103
ROUT = 66
20
10
1×103
30
IOUT = 100μA
100×100
40
100
10×100
50
1×100
OUTPUT IMPEDANCE ()
INPUT CURRENT (mA)
60
3
2
COUT = 4.7μF
1
IOUT = 100mA
0
2
0
0
FIGURE 2-21:
Version).
DS20005614B-page 8
50
100
150
TIME (μs)
200
250
300
Enable Transient (3.3V
1.4
CIN = 2.2μF
COUT = 4.7μF
1.2
1.0
ON
0.8
OFF
0.6
0.4
-60
-30
FIGURE 2-24:
vs. Temperature.
0
30
60
90
120
150
TEMPERATURE (ºC)
Enable Voltage Threshold
2016 - 2022 Microchip Technology Inc. and its subsidiaries
MIC5202
80
IOUT = 100μA
60
40
FIGURE 2-25:
FREQUENCY (Hz)
1×106
100×103
10×103
1×103
0
100×100
20
10×100
RIPPLE VOLTAGE (dB)
100
Ripple vs. Frequency.
80
IOUT = 1mA
60
40
FIGURE 2-26:
FREQUENCY (Hz)
1×106
100×103
10×103
1×103
0
100×100
20
10×100
RIPPLE VOLTAGE (dB)
100
Ripple vs. Frequency.
80
IOUT = 100mA
60
40
FIGURE 2-27:
FREQUENCY (Hz)
1×106
100×103
10×103
1×103
0
100×100
20
10×100
RIPPLE VOLTAGE (dB)
100
Ripple vs. Frequency.
2016 - 2022 Microchip Technology Inc. and its subsidiaries
DS20005614B-page 9
MIC5202
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
Package Type
MIC5202
8-Lead SOIC (M)
(Top View)
TABLE 3-1:
VOUT1
1
8
VIN1
GND1
2
7
EN1
VOUT2
3
6
VIN2
GND2
4
5
EN2
PIN FUNCTION TABLE
Pin Number
Pin Name
Description
1
VOUT1
Output of regulator 1.
2
GND1
Ground pin of LDO1.
3
VOUT2
Output of regulator 2.
4
GND2
5
EN2
Ground pin of LDO2.
Enable input for LDO2. Active-high Input. Logic-high = On, logic-low = Off. Do not
leave floating.
6
VIN2
Voltage input for LDO2.
7
EN1
Enable input for LDO1. Active-high Input. Logic-high = On, logic-low = Off. Do not
leave floating.
8
VIN1
Voltage input for LDO1.
DS20005614B-page 10
2016 - 2022 Microchip Technology Inc. and its subsidiaries
MIC5202
4.0
APPLICATION INFORMATION
The MIC5202 is a dual linear voltage regulator with low
dropout voltage and low ground current features. Ideal
for battery-operated applications, the MIC5202 offers
1% output voltage accuracy, two independent enable
pins, reversed battery protection, short circuit current
limit and overtemperature protection. When the
MIC5202 is disabled, the ground pin current drops to
sub-micro amp and prolongs the battery life.
4.1
Input Supply Voltage
VIN1 and VIN2 provide power to each internal circuit and
may be tied together.
4.2
regulator and sends it to a “zero” off-mode-current
state. In this state, current consumed by the regulator
goes nearly to zero. Forcing the enable pin high
enables the output voltage. The active-high enable pin
typically consumes 8 µA of current and cannot be left
floating; a floating enable pin may cause an
indeterminate state on the output.
4.7
Thermal Shutdown
When the internal die temperature of MIC5202 reaches
the limit, the internal driver is disabled until the die
temperature falls.
Ground
Both ground pins (Pin 2 and 4) must be tied to the same
ground potential when using a single power supply.
4.3
Input Capacitor
A 1 µF tantalum or aluminum electrolytic capacitor
should be placed close to each VIN pin if there is more
than 10 inches of copper between the input and the
capacitor, or if a battery is used as the supply.
4.4
Output Capacitor
The MIC5202 requires an output capacitor of 1 µF or
greater to maintain stability. Increasing the output
capacitor leads to an improved transient response;
however, the size and cost also increase. Most
tantalum and aluminum electrolytic capacitors are
adequate; film capacitors will work as well, but at a
higher cost. Many aluminum electrolytics have
electrolytes that freeze at –30°C, so tantalum
capacitors are recommended for operations below
–25°C. An equivalent series resistance (ESR) of 5Ω or
less with a resonance frequency above 500 kHz is
recommended. The output capacitor value may be
increased without limit.
At lower output loads, a smaller output capacitor value
is required for output stability. The capacitor can be
reduced to 0.47 µF for current below 10 mA or 0.33 µF
for current below 1 mA.
4.5
No-Load Stability
Unlike many other voltage regulators, the MIC5202
remains stable and in regulation with no load. This is
especially important in CMOS RAM keep-alive
applications.
4.6
Enable Input
The MIC5202 features dual active-high enable pins
that allow each regulator to be enabled and disabled
independently. Forcing the enable pin low disables the
2016 - 2022 Microchip Technology Inc. and its subsidiaries
DS20005614B-page 11
MIC5202
5.0
THERMAL CONSIDERATIONS
5.1
Layout
The MIC5202 (8-lead SOIC package) has the thermal
characteristics shown in Table 5-1, when mounted on a
single-layer copper-clad printed circuit board.
TABLE 5-1:
THERMAL CHARACTERISTIC
CONSIDERATIONS
PC Board Dielectric
θJA
FR4
160°C/W
Ceramic
120°C/W
Multi-layer boards with a dedicated ground plane, wide
traces, and large supply bus lines provide better
thermal conductivity.
The “worst case” value of 160°C/W assumes no ground
plane, minimum trace widths, and a FR4 material
board.
5.2
Nominal Power Dissipation and
Die Temperature
At +25°C ambient temperature, the MIC5202 operates
reliably at up to 625 mW when mounted in the “worst
case” manner described in the previous section. At an
ambient temperature of +55°C, the device can safely
dissipate 440 mW. These power levels are equivalent
to a die temperature of +125°C, which corresponds to
the recommended maximum temperature for
nonmilitary grade silicon integrated circuits.
DS20005614B-page 12
2016 - 2022 Microchip Technology Inc. and its subsidiaries
MIC5202
6.0
PACKAGING INFORMATION
6.1
Package Marking Information
8-Lead SOIC*
XXXX
XXXX
WNNNC
Legend: XX...X
Y
YY
WW
NNN
e3
*
Example
5202
48YM
73R9C
Product code or customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle
mark).
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information. Package may or may not include
the corporate logo.
Underbar (_) symbol may not be to scale.
Note:
If the full seven-character YYWWNNN code cannot fit on the package, the following truncated codes are
used based on the available marking space:
6 Characters = YWWNNN; 5 Characters = WWNNN; 4 Characters = WNNN; 3 Characters = NNN;
2 Characters = NN; 1 Character = N
2016 - 2022 Microchip Technology Inc. and its subsidiaries
DS20005614B-page 13
MIC5202
8-Lead SOIC Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
DS20005614B-page 14
2016 - 2022 Microchip Technology Inc. and its subsidiaries
MIC5202
APPENDIX A:
REVISION HISTORY
Revision A (August 2016)
• Converted Micrel document MIC5202 to Microchip data sheet DS20005614A.
• Minor text changes throughout.
Revision B (February 2022)
• Updated the Package Marking Information drawing with the most current information.
• Minor grammar and style corrections throughout.
2016 - 2022 Microchip Technology Inc. and its subsidiaries
DS20005614B-page 15
MIC5202
NOTES:
DS20005614B-page 16
2016 - 2022 Microchip Technology Inc. and its subsidiaries
MIC5202
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office.
–
PART NO.
Device
X.X
X
XX
–
X.X
Examples:
a) MIC5202-3.0YM:
Dual 100 mA Low-Dropout
b) MIC5202-3.0YM-TR:
Dual 100 mA Low-Dropout
Regulator, 3.0 Voltage,
–40°C to +125°C Temp. Range,
8-Pin SOIC, 2,500/Reel
c) MIC5202-3.3YM:
Dual 100 mA Low-Dropout
Regulator, 3.3V Voltage,
–40°C to +125°C Temp. Range,
8-Pin SOIC, 95/Tube
d) MIC5202-3.3YM-TR:
Dual 100 mA Low-Dropout
Regulator, 3.3V Voltage,
–40°C to +125°C Temp. Range,
8-Pin SOIC, 2,500/Reel
e) MIC5202-4.8YM:
Dual 100 mA Low-Dropout
Regulator, 4.85V Voltage,
–40°C to +125°C Temp. Range,
8-Pin SOIC, 95/Tube
f)
Dual 100 mA Low-Dropout
Regulator, 4.85V Voltage,
–40°C to +125°C Temp. Range,
8-Pin SOIC, 2,500/Reel
Output Temperature Package Media Type
Voltage
Device:
MIC5202:
Output Voltage:
3.0
3.3
4.8
5.0
=
=
=
=
Dual 100 mA Low-Dropout Regulator
3.0V
3.3V
4.85V
5.0V
Temperature:
Y
=
–40°C to +125°C
Package:
M
=
8-Pin SOIC
Media Type:
TR =
blank=
2,500/Reel
95/Tube
2016 - 2022 Microchip Technology Inc. and its subsidiaries
MIC5202-4.8YM-TR:
Regulator, 3.0V Voltage,
–40°C to +125°C Temp. Range,
8-Pin SOIC, 95/Tube
g) MIC5202-5.0YM:
Dual 100 mA Low-Dropout
Regulator, 5.0V Voltage,
–40°C to +125°C Temp. Range,
8-Pin SOIC, 95/Tube
h) MIC5202-5.0YM-TR:
Dual 100 mA Low-Dropout
Regulator, 5.0V Voltage,
–40°C to +125°C Temp. Range,
8-Pin SOIC, 2,500/Reel
DS20005614B-page 17
MIC5202
NOTES:
DS20005614B-page 18
2016 - 2022 Microchip Technology Inc. and its subsidiaries
Note the following details of the code protection feature on Microchip products:
•
Microchip products meet the specifications contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and
under normal conditions.
•
Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of
Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not
mean that we are guaranteeing the product is “unbreakable”. Code protection is constantly evolving. Microchip is committed to
continuously improving the code protection features of our products.
This publication and the information herein may be used only
with Microchip products, including to design, test, and integrate
Microchip products with your application. Use of this information in any other manner violates these terms. Information
regarding device applications is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your
specifications. Contact your local Microchip sales office for
additional support or, obtain additional support at https://
www.microchip.com/en-us/support/design-help/client-supportservices.
THIS INFORMATION IS PROVIDED BY MICROCHIP "AS IS".
MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED,
WRITTEN OR ORAL, STATUTORY OR OTHERWISE,
RELATED TO THE INFORMATION INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A
PARTICULAR PURPOSE, OR WARRANTIES RELATED TO
ITS CONDITION, QUALITY, OR PERFORMANCE.
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY
KIND WHATSOEVER RELATED TO THE INFORMATION OR
ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS
BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES
ARE FORESEEABLE. TO THE FULLEST EXTENT
ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON
ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION
OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF
ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP
FOR THE INFORMATION.
Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to
defend, indemnify and hold harmless Microchip from any and
all damages, claims, suits, or expenses resulting from such
use. No licenses are conveyed, implicitly or otherwise, under
any Microchip intellectual property rights unless otherwise
stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec,
AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud,
CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO,
JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus,
maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo,
MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower,
PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch,
SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash,
Symmetricom, SyncServer, Tachyon, TimeSource, tinyAVR, UNI/O,
Vectron, and XMEGA are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
AgileSwitch, APT, ClockWorks, The Embedded Control Solutions
Company, EtherSynch, Flashtec, Hyper Speed Control, HyperLight
Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3,
Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, QuietWire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub,
TimePictra, TimeProvider, TrueTime, WinPath, and ZL are
registered trademarks of Microchip Technology Incorporated in the
U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky,
BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive,
CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net,
Dynamic Average Matching, DAM, ECAN, Espresso T1S,
EtherGREEN, GridTime, IdealBridge, In-Circuit Serial
Programming, ICSP, INICnet, Intelligent Paralleling, Inter-Chip
Connectivity, JitterBlocker, Knob-on-Display, maxCrypto, maxView,
memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo,
MPLIB, MPLINK, MultiTRAK, NetDetach, NVM Express, NVMe,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple
Blocker, RTAX, RTG4, SAM-ICE, Serial Quad I/O, simpleMAP,
SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI,
SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total
Endurance, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY,
ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks
of Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage
Technology, Symmcom, and Trusted Time are registered
trademarks of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany
II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in
other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2016 - 2022, Microchip Technology Incorporated and its subsidiaries.
All Rights Reserved.
For information regarding Microchip’s Quality Management Systems,
please visit www.microchip.com/quality.
2016 - 2022 Microchip Technology Inc. and its subsidiaries
ISBN: 978-1-5224-9873-5
DS20005614B-page 19
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
DS20005614B-page 20
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Denmark - Copenhagen
Tel: 45-4485-5910
Fax: 45-4485-2829
Finland - Espoo
Tel: 358-9-4520-820
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-72400
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7288-4388
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
2016 - 2022 Microchip Technology Inc. and its subsidiaries
09/14/21
工商网监
湘ICP备2023018690号
