MIC5203
µCap 80 mA LDO Regulator
Features
General Description
•
•
•
•
•
•
•
•
•
•
•
The MIC5203 is a µCap 80 mA linear voltage regulator
with very low dropout voltage (typically 20 mV at light
loads and 300 mV at 80 mA) and very low ground
current (225 µA at 20 mA output), offering better than
3% initial accuracy with a logic-compatible enable
input.
Tiny 4- and 5-Lead Surface-Mount Packages
Wide Selection of Output Voltages
Guaranteed 80 mA Output
Low Quiescent Current
Low Dropout Voltage
Low Temperature Coefficient
Current and Thermal Limiting
Reversed Input Polarity Protection
Zero Off-Mode Current
Logic-Controlled Shutdown
Stability with Low-ESR Ceramic Capacitors
Applications
•
•
•
•
•
•
Cellular Telephones
Laptop, Notebook, and Palmtop Computers
Battery-Powered Equipment
Barcode Scanners
SMPS Post-Regulator and DC/DC Modules
High-Efficiency Linear Power Supplies
The µCap regulator design is optimized to work with
low- value, low-cost ceramic capacitors. The outputs
typically require only 0.47 µF of output capacitance for
stability.
Designed especially for hand-held, battery-powered
devices, the MIC5203 can be controlled by a CMOS or
TTL compatible logic signal. When disabled, power
consumption drops nearly to zero. If on-off control is not
required, the enable pin may be tied to the input for 3terminal operation. The ground current of the MIC5203
increases only slightly in dropout, further prolonging
battery life. Key MIC5203 features include current
limiting, overtemperature shutdown, and protection
against reversed battery.
The MIC5203 is available in 2.8V, 3.0V, 3.3V, 3.6V,
3.8V, 4.0V, 4.5V, 4.75V, and 5.0V fixed voltages. Other
voltages are available.
Package Types
MIC5203
4-Lead SOT-143 (M4)
MIC5203
5-Lead SOT-23 (M5)
EN
GND
2
1
Part
Identification
E N GND IN
3
LAxx
2
1
LKxx
3
4
4
5
IN
OUT
NC
OUT
2021 Microchip Technology Inc. and its subsidiaries
DS20006609A-page 1
MIC5203
Typical Application Circuits
MIC5203
4-Lead SOT-143
Enable
Shutdown
2
1
1
LAxx
3
DS20006609A-page 2
MIC5203
5-Lead SOT-23
5
2
4
VOUT
0.47μF
Enable
Shutdown
3
VOUT
0.47μF
4
2021 Microchip Technology Inc. and its subsidiaries
MIC5203
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Supply Input Voltage (VIN) .......................................................................................................................... –20V to +20V
Enable Input Voltage (VEN) ......................................................................................................................... –20V to +20V
Power Dissipation (PD) (Note 1) ............................................................................................................ Internally Limited
Operating Ratings ‡
Supply Input Voltage (VIN) ......................................................................................................................... +2.5V to +16V
Enable Input Voltage (VEN) .................................................................................................................................0V to VIN
† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
‡ Notice: The device is not guaranteed to function outside its operating ratings.
Note 1: The maximum allowable power dissipation at any TA (ambient temperature) is PD(MAX) = (TJ(MAX) – TA)/JA.
Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. The JA of the MIC5205-xxYM5 (all versions) is 220°C/W mounted on
a PC board.
ELECTRICAL CHARACTERISTICS
Electrical Characteristics: VIN = VOUT +1V; IL = 1 mA; CL = 0.47 µF; VEN ≥ 2.0V; TJ = +25°C, bold values indicate
–40°C < TJ ≤ +125°C, unless noted.
Parameter
Output Voltage Accuracy
Symbol
VO
Output Voltage Temperature
Coefficient
ΔVO/ΔT
Line Regulation
ΔVO/VO
Load Regulation
ΔVO/VO
Dropout Voltage, Note 3
Quiescent Current
Ground Pin Current, Note 4
Ground Pin Current at
Dropout
Current Limit
Thermal Regulation
Min.
Typ.
Max.
–3
—
3
–4
—
4
—
50
200
—
0.008
0.3
—
—
0.5
—
0.08
0.3
—
—
0.5
Units
%
ppm/°C
Conditions
—
Note 1
%
VIN = VOUT + 1V to 16V
%
IL = 0.1 mA to 80 mA, Note 2
—
20
—
—
200
350
—
250
—
—
300
600
—
0.01
10
—
180
—
—
225
750
—
850
—
—
1800
3000
IGNDDO
—
200
300
µA
VIN = VOUT(nom) – 0.5V, Note 4
ILIMIT
—
180
250
mA
VOUT = 0V
ΔVO/ΔPD
—
0.05
—
%/W
ΔVO/VO
IQ
IGND
2021 Microchip Technology Inc. and its subsidiaries
IL = 100 µA
mV
IL = 20 mA
IL = 50 mA
IL = 80 mA
µA
VEN ≤ 0.4V (shutdown)
IL = 100 µA, VEN ≥ 2.0V (active)
µA
IL = 20 mA, VEN ≥ 2.0V (active)
IL = 50 mA, VEN ≥ 2.0V (active)
IL = 80 mA, VEN ≥ 2.0V (active)
Note 5
DS20006609A-page 3
MIC5203
ELECTRICAL CHARACTERISTICS (CONTINUED)
Electrical Characteristics: VIN = VOUT +1V; IL = 1 mA; CL = 0.47 µF; VEN ≥ 2.0V; TJ = +25°C, bold values indicate
–40°C < TJ ≤ +125°C, unless noted.
Parameter
Symbol
Min.
Typ.
Max.
—
—
0.6
Units
Conditions
ENABLE Input
Enable Input Voltage Level
Enable Input Current
Note 1:
2:
3:
4:
5:
VIL
2.0
—
—
IIL
—
0.01
1
IIH
—
15
50
V
µA
Logic low (off)
Logic low (on)
VIL ≤ 0.6V
VIH ≥ 2.0V
Output voltage temperature coefficient is defined as the worst case voltage change divided by the total
temperature range.
Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are
tested for load regulation in the load range from 0.1 mA to 150 mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification.
Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below its
nominal value measured at 1V differential.
Ground pin current is the regulator quiescent current plus pass transistor base current. The total current
drawn from the supply is the sum of the load current plus the ground pin current.
Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 150 mA load pulse at VIN =
16V for t = 10 ms.
TEMPERATURE SPECIFICATIONS (Note 1)
Parameters
Symbol
Min.
Typ.
Max.
Units
Conditions
Junction Temperature Range
TJ
–40
—
+125
°C
Storage Temperature Range
TS
–60
—
+150
°C
—
Lead Temperature
—
—
—
+260
°C
Soldering, 5s
—
250
—
°C/W
—
220
—
°C/W
Temperature Ranges
—
Package Thermal Resistances
Thermal Resistance SOT-143
Thermal Resistance SOT-23-5
Note 1:
2:
JA
Note 2
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, JA). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
The maximum allowable power dissipation at any TA (ambient temperature) is PD(max) = (TJ(max) – TA)/JA.
Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
DS20006609A-page 4
2021 Microchip Technology Inc. and its subsidiaries
MIC5203
2.0
Note:
TYPICAL PERFORMANCE CURVES
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
2000
CIN = 10PF
COUT = 1PF
GROUND CURRENT
DROPOUT VOLTAGE (mV)
1000
100
10
1500
1000
500
VIN = VOUT + 1V
1
0.01
FIGURE 2-1:
Current.
0
0.1
1
10
100
OUTPUT CURRENT (mA)
Dropout Voltage vs. Output
FIGURE 2-4:
Current.
Ground Current vs. Output
2.0
CIN = 10PF
COUT = 1PF
GROUND CURRENT (mA)
DROPOUT VOLTAGE (mV)
400
300
IL = 80mA
200
100
IL = 1mA
IL = 100PA
Dropout Voltage vs.
IL = 100PA
0.5
FIGURE 2-5:
Voltage.
GROUND CURRENT (mA)
OUTPUT VOLTAGE (V)
FIGURE 2-3:
1
2
3
4 5 6
SUPPLY VOLTAGE (V)
7
Ground Current vs. Supply
3.0
IL = 100PA
3
2
IL = 80mA
1
CIN = 10PF
COUT = 1PF
0
VOUT = 3.3V
1.0
0.0
0
4
IL = 50mA
1.5
0
-60 -30 0 30 60 90 120 150
TEMPERATURE qC)
(
FIGURE 2-2:
Temperature.
0 10 20 30 40 50 60 70 80
OUTPUT CURRENT (mA)
0
1
2
3
4 5 6
SUPPLY VOLTAGE (V)
7
Dropout Characteristics.
2021 Microchip Technology Inc. and its subsidiaries
2.5
2.0
CIN = 10PF
COUT = 1PF
IL = 80mA
1.5
1.0
IL = 50mA
0.5
IL = 100PA
0.0
-60 -30 0 30 60 90 120 150
TEMPERATURE qC)
(
FIGURE 2-6:
Temperature.
Ground Current vs.
DS20006609A-page 5
4.0
3.5
3.8
OUTPUT VOLTAGE
4.0
3.0
2.5
CIN = 10PF
COUT = 1PF
2.0
1.5
1.0
0.0
0
Output Voltage vs. Output
3.2
3.0
2.8
140
120
100
80
60
CIN = 10PF
COUT = 1PF
40
20
0
FIGURE 2-8:
Voltage.
1
2
3
4 5 6
INPUT VOLTAGE (V)
50
0
DS20006609A-page 6
Output Voltage vs.
180
160
140
CIN = 10PF
COUT = 1PF
120
FIGURE 2-11:
Temperature.
Short Circuit Current vs.
3.5
60
40
20
0
-20
-40
-60
100
FIGURE 2-9:
(3.3V Version).
CURVES APPLICABLE
AT 100PA AND 50mA
100
-60 -30 0 30 60 90 120 150
TEMPERATURE qC)
(
7
Short Circuit vs. Input
-50
-2 0
3 DEVICES
HI / AVG / LO
200
OUTPUT CURRENT (mA)
SHORT CIRCUIT CURRENT (mA)
3.4
FIGURE 2-10:
Temperature.
160
0
CIN = 10PF
COUT = 1PF
2.4
-60 -30 0 30 60 90 120 150
TEMPERATURE qC)
(
50
100
150
200
OUTPUT CURRENT (mA)
FIGURE 2-7:
Current.
/2$' P$ ǻ287387 P9
3.6
2.6
0.5
CL = 1PF
2
4 6 8 10 12 14 16
TIME (ms)
Thermal Regulation
MIN. SUPPLY VOLTAGE (V)
OUTPUT VOLTAGE (V)
MIC5203
IL = 1mA
VOUT = 3.3V
3.4
CIN = 10PF
COUT = 1PF
3.3
-60 -30 0 30 60 90 120 150
TEMPERATURE qC)
(
FIGURE 2-12:
Temperature.
Minimum Supply Voltage vs.
2021 Microchip Technology Inc. and its subsidiaries
MIC5203
OUTPUT (V)
287387 P$ ǻ287387 P9
200
0
COUT = 1PF
VIN = VOUT + 1
-200
50
0
-50
-1 0
FIGURE 2-13:
1
2 3 4 5
TIME (ms)
6 7
CL = 11PF
IL = 1mA
1
0
-1
8
INPUT (V)
100
2
6
4
0.0
8
FIGURE 2-16:
Load Transient.
0.2 0.4 0.6
TIME (ms)
0.8
1.0
Line Transient.
100
RIPPLE VOLTAGE (dB)
0
5
10
TIME (ms)
15
20
1x106
20
0
0
IL = 100PA
CL = 1PF
VIN = VOUT + 1
100x103
50
40
10x103
100
-200
60
1x103
COUT = 10PF
VIN = VOUT + 1
-100
80
100x100
0
10x100
287387 P$ ǻ287387
100
FREQUENCY (Hz)
FIGURE 2-14:
Load Transient.
FIGURE 2-17:
Frequency.
Ripple Voltage vs.
60
40
FIGURE 2-15:
0.8
1.0
Line Transient.
2021 Microchip Technology Inc. and its subsidiaries
1x106
0.2 0.4 0.6
TIME (ms)
100x103
0
10x103
20
4
0.0
IL = 1mA
CL = 1PF
VIN = VOUT + 1
1x103
6
80
100x100
CL = 1PF
IL = 1mA
10x100
3
2
1
0
-1
8
-2
RIPPLE VOLTAGE (dB)
,1387 9 ǻ287387
100
FREQUENCY (Hz)
FIGURE 2-18:
Frequency.
Ripple Voltage vs.
DS20006609A-page 7
MIC5203
OUTPUT (V)
80
60
40
1x106
100x103
1x103
10x100
0
100x100
20
10x103
IL = 50mA
CL = 1PF
VIN = VOUT + 1
4.0
3.0
2.0
1.0
0.0
4
-1.0
ENABLE (V)
RIPPLE VOLTAGE (dB)
100
CL = 1PF
IL = 100PA
2
0
0
2
4
6
TIME (ms)
8
10
FREQUENCY (Hz)
FIGURE 2-19:
Frequency.
Ripple Voltage vs.
FIGURE 2-22:
(3.3 Version).
Enable Characteristics
ENABLE VOLTAGE (mV)
1.50
100
IL = 100PA
10
IL = 1mA
1
1x106
100x103
1x103
0.01
100x100
0.1
10x103
IL = 100mA
10x100
287387,03('$1&( ȍ
1000
CIN = 10PF
COUT = 1PF
IL = 1mA
1.25
1.00
VOFF
VON
0.75
0.50
-60 -30 0 30 60 90 120 150
TEMPERATURE qC)
(
FREQUENCY (Hz)
Output Impedance.
FIGURE 2-23:
Temperature.
Enable Voltage vs.
ENABLE CURRENT (V)
40
5
4
3
2
1
0
4
-1
ENABLE (V)
OUTPUT (V)
FIGURE 2-20:
CL = 1PF
IL = 100PA
2
0
0.0
FIGURE 2-21:
(3.3 Version).
DS20006609A-page 8
0.2 0.4 0.6
TIME (ms)
0.8
30
20
10
VEN = 5V
VEN = 2V
0
-60 -30 0 30 60 90 120 150
TEMPERATURE qC)
(
1.0
Enable Characteristics
CIN = 10PF
COUT = 1PF
IL = 1mA
FIGURE 2-24:
Temperature.
Enable Current vs.
2021 Microchip Technology Inc. and its subsidiaries
MIC5203
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
Pin Number
SOT-143
Pin Number
SOT-23-5
1
2
GND
2
3
EN
Enable (Input): TTL/CMOS compatible control input.
Logic high = enabled; logic low or open = shutdown
Pin Name Description
Ground
3
1
IN
Supply input
—
4
NC
Not internally connected
4
5
OUT
2021 Microchip Technology Inc. and its subsidiaries
Regulator output
DS20006609A-page 9
MIC5203
4.0
APPLICATION INFORMATION
4.1
Input Capacitor
A 0.1 µF capacitor should be placed from IN to GND if
there are more than 10 inches of wire between the
input and the AC filter capacitor or if a battery is used
as the input.
4.2
Output Capacitor
Typical PNP based regulators require an output
capacitor to prevent oscillation. The MIC5203 is
ultra-stable, requiring only 0.47 µF of output
capacitance for stability. The regulator is stable with all
types of capacitors, including the tiny, low-ESR ceramic
chip capacitors. The output capacitor value can be
increased without limit to improve transient response.
4.3
No-Load Stability
The MIC5203 will remain stable and in regulation with
no load (other than the internal voltage divider) unlike
many other voltage regulators. This is especially
important in CMOS RAM keep-alive applications.
4.4
Enable Input
The MIC5203 features nearly zero off-mode current.
When EN (enable input) is held below 0.6V, all internal
circuitry is powered off. Pulling EN high (over 2.0V) reenables the device and allows operation. EN draws a
small amount of current, typically 15 µA. While the logic
threshold is TTL/CMOS compatible, EN may be pulled
as high as 20V, independent of VIN.
The capacitor should have a resonant frequency above
500 kHz. Ceramic capacitors work, but some
dielectrics have poor temperature coefficients, which
will affect the value of the output capacitor over
temperature. Tantalum capacitors are much more
stable over temperature, but typically are larger and
more expensive. Aluminum electrolytic capacitors will
also work, but they have electrolytes that freeze at
about –30°C. Tantalum or ceramic capacitors are
recommended for operation below –25°C.
DS20006609A-page 10
2021 Microchip Technology Inc. and its subsidiaries
MIC5203
5.0
PACKAGING INFORMATION
5.1
Package Marking Information
TABLE 5-1:
4-Lead SOT-143*
Example
XXXX
NNN
LA33
415
5-Lead SOT-23*
Example
XXXX
NNN
LK45
415
MARKING CODES
SOT-143 Part #
Marking
Voltage
SOT-23 Part #
Marking
Voltage
MIC5203-2.6YM4
LA26
2.6V
MIC5203-2.6YM5
LK26
2.6V
MIC5203-2.8YM4
LA28
2.8V
MIC5203-2.8YM5
LK28
2.8V
MIC5203-3.0YM4
LA30
3.0V
MIC5203-3.0YM5
LK30
3.0V
MIC5203-3.3YM4
LA33
3.3V
MIC5203-3.3YM5
LK33
3.3V
MIC5203-3.6YM4
LA36
3.6V
MIC5203-3.6YM5
LK36
3.6V
MIC5203-3.8YM4
LA38
3.8V
MIC5203-3.8YM5
LK38
3.8V
MIC5203-4.0YM4
LA40
4.0V
MIC5203-4.0YM5
LK40
4.0V
MIC5203-4.5YM4
LA45
4.5V
MIC5203-4.5YM5
LK45
4.5V
MIC5203-4.7YM4
LA47
4.7V
MIC5203-4.7YM5
LK47
4.7V
MIC5203-5.0YM4
LA50
5.0V
MIC5203-5.0YM5
LK50
5.0V
Legend: XX...X
Y
YY
WW
NNN
e3
*
Product code or customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle
mark).
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information. Package may or may not include
the corporate logo.
Underbar (_) and/or Overbar (‾) symbol may not be to scale.
2021 Microchip Technology Inc. and its subsidiaries
DS20006609A-page 11
MIC5203
4-Lead SOT-143 Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
DS20006609A-page 12
2021 Microchip Technology Inc. and its subsidiaries
MIC5203
5-Lead SOT-23 Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
2021 Microchip Technology Inc. and its subsidiaries
DS20006609A-page 13
MIC5203
NOTES:
DS20006609A-page 14
2021 Microchip Technology Inc. and its subsidiaries
MIC5203
APPENDIX A:
REVISION HISTORY
Revision A (November 2021)
• Converted Micrel document MIC5203 to Microchip data sheet DS20006609A.
• Minor text changes throughout.
2021 Microchip Technology Inc. and its subsidiaries
DS20006609A-page 15
MIC5203
NOTES:
DS20006609A-page 16
2021 Microchip Technology Inc. and its subsidiaries
MIC5203
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office.
–X.X
PART NO.
Device
X
Voltage Temperature
Device:
MIC5203:
Voltage:
2.8
3.0
3.3
3.6
3.8
4.0
4.5
4.75
5.0
=
=
=
=
=
=
=
=
=
2.8V
3.0V
3.3V
3.6V
3.8V
4.0V
4.5V
4.75V
5.0V
Temperature:
Y
=
–40°C to +125°C
Package:
M4
M5
=
=
4-Lead SOT-143
5-Lead SOT-23
Media Type:
TR
=
3,000/Reel
XX
–XX
Package
Media Type
µCap 80 mA LDO Regulator
2021 Microchip Technology Inc. and its subsidiaries
Examples:
a) MIC5203-2.8YM4-TR
MIC5203, µCap 80 mA LDO
Regulator, –40°C to +125°C,
Temperature Range, 4-Lead
SOT-143, 3,000/Reel
b) MIC5203-5.0YM5-TR
MIC5203, µCap 80 mA LDO
Regulator, –40°C to +125°C,
Temperature Range, 5-Lead
SOT-23-5, 3,000/Reel
Note 1:
Tape and Reel identifier only appears in the
catalog part number description. This identifier is
used for ordering purposes and is not printed on
the device package. Check with your Microchip
Sales Office for package availability with the
Tape and Reel option.
DS20006609A-page 17
MIC5203
NOTES:
DS20006609A-page 18
2021 Microchip Technology Inc. and its subsidiaries
Note the following details of the code protection feature on Microchip products:
•
Microchip products meet the specifications contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and
under normal conditions.
•
Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of
Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not
mean that we are guaranteeing the product is “unbreakable”. Code protection is constantly evolving. Microchip is committed to
continuously improving the code protection features of our products.
This publication and the information herein may be used only
with Microchip products, including to design, test, and integrate
Microchip products with your application. Use of this information in any other manner violates these terms. Information
regarding device applications is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your
specifications. Contact your local Microchip sales office for
additional support or, obtain additional support at https://
www.microchip.com/en-us/support/design-help/client-supportservices.
THIS INFORMATION IS PROVIDED BY MICROCHIP "AS IS".
MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED,
WRITTEN OR ORAL, STATUTORY OR OTHERWISE,
RELATED TO THE INFORMATION INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A
PARTICULAR PURPOSE, OR WARRANTIES RELATED TO
ITS CONDITION, QUALITY, OR PERFORMANCE.
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY
KIND WHATSOEVER RELATED TO THE INFORMATION OR
ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS
BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES
ARE FORESEEABLE. TO THE FULLEST EXTENT
ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON
ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION
OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF
ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP
FOR THE INFORMATION.
Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to
defend, indemnify and hold harmless Microchip from any and
all damages, claims, suits, or expenses resulting from such
use. No licenses are conveyed, implicitly or otherwise, under
any Microchip intellectual property rights unless otherwise
stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec,
AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud,
CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO,
JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus,
maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo,
MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower,
PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch,
SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash,
Symmetricom, SyncServer, Tachyon, TimeSource, tinyAVR, UNI/O,
Vectron, and XMEGA are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
AgileSwitch, APT, ClockWorks, The Embedded Control Solutions
Company, EtherSynch, Flashtec, Hyper Speed Control, HyperLight
Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3,
Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, QuietWire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub,
TimePictra, TimeProvider, TrueTime, WinPath, and ZL are
registered trademarks of Microchip Technology Incorporated in the
U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky,
BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive,
CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net,
Dynamic Average Matching, DAM, ECAN, Espresso T1S,
EtherGREEN, GridTime, IdealBridge, In-Circuit Serial
Programming, ICSP, INICnet, Intelligent Paralleling, Inter-Chip
Connectivity, JitterBlocker, Knob-on-Display, maxCrypto, maxView,
memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo,
MPLIB, MPLINK, MultiTRAK, NetDetach, NVM Express, NVMe,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple
Blocker, RTAX, RTG4, SAM-ICE, Serial Quad I/O, simpleMAP,
SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI,
SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total
Endurance, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY,
ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks
of Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage
Technology, Symmcom, and Trusted Time are registered
trademarks of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany
II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in
other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2021, Microchip Technology Incorporated and its subsidiaries.
All Rights Reserved.
For information regarding Microchip’s Quality Management Systems,
please visit www.microchip.com/quality.
2021 Microchip Technology Inc. and its subsidiaries
ISBN: 978-1-5224-9289-4
DS20006609A-page 19
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
DS20006609A-page 20
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Denmark - Copenhagen
Tel: 45-4485-5910
Fax: 45-4485-2829
Finland - Espoo
Tel: 358-9-4520-820
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-72400
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7288-4388
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
2021 Microchip Technology Inc. and its subsidiaries
09/14/21
工商网监
湘ICP备2023018690号
