MIC5246-2.1BM5-TR

MIC5246 Micrel MIC5246 150mA µCap CMOS LDO Regulator Final Information General Description Features The MIC5246 is an efficient, precise CMOS voltage regulator optimized for low-noise applications. The MIC5246 offers better than 1% initial accuracy, extremely-low-dropout voltage (typically 150mV at 150mA) and constant ground current (typically 85µA)over load . The MIC5246 features an error flag that indicates an output fault condition such as overcurrent, thermal shutdown and dropout. The MIC5246 provides a very low noise output, ideal for RF applications where quiet voltage sources are required. • • • • • • • • • • • Designed specifically for hand-held and battery-powered devices, the MIC5246 provides a TTL-logic-compatible enable pin. When disabled, power consumption drops nearly to zero. Error flag indicates fault condition Ultralow dropout—100mV @ 100mA Load independent, ultralow ground current: 85µA 150mA output current Current limiting Thermal Shutdown Tight load and line regulation “Zero” off-mode current Stability with low-ESR capacitors Fast transient response TTL-Logic-controlled enable input Applications • • • • • • • • The MIC5246 also works with low-ESR ceramic capacitors, reducing the amount of board space necessary for power applications, critical in hand-held wireless devices. Key features include current limit, thermal shutdown, a pushpull output for faster transient response, and an active clamp to speed up device turnoff. Available in the IttyBitty™ SOT-23-5 package, the MIC5246 also offers a range of fixed output voltages. Cellular phones and pagers Cellular accessories Battery-powered equipment Laptop, notebook, and palmtop computers PCMCIA VCC and VPP regulation/switching Consumer/personal electronics SMPS post-regulator/dc-to-dc modules High-efficiency linear power supplies Ordering Information Part Number Marking Voltage Junction Temp. Range Package MIC5246-2.6BM5 LT26 2.6V –40°C to +125°C SOT-23-5 MIC5246-2.7BM5 LT27 2.7V –40°C to +125°C SOT-23-5 MIC5246-2.8BM5 LT28 2.8V –40°C to +125°C SOT-23-5 MIC5246-2.85BM5 LT2J 2.85V –40°C to +125°C SOT-23-5 MIC5246-3.0BM5 LT30 3.0V –40°C to +125°C SOT-23-5 MIC5246-3.3BM5 LT33 3.3V –40°C to +125°C SOT-23-5 Other voltages available. Contact Micrel for details. Typical Application 47kΩ VIN MIC5246-x.xBM5 1 5 2 COUT 3 Enable Shutdown VOUT 4 FLG CFLG EN EN (pin 3) may be connected directly to IN (pin 1). Low-Noise Regulator Application IttyBitty is a trademark of Micrel, Inc. Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 944-0970 • http://www.micrel.com June 2000 1 MIC5246 MIC5246 Micrel Pin Configuration EN GND IN 3 2 1 LTxx 4 5 FLG OUT MIC5246-x.xBM5 Pin Description Pin Number Pin Name Pin Function 1 IN Supply Input 2 GND 3 EN Enable/Shutdown (Input): CMOS compatible input. Logic high = enable; logic low = shutdown. Do not leave open. 4 FLG Error Flag (Output): Open-drain output. Active low indicates an output undervoltage condition. 5 OUT Regulator Output Ground Absolute Maximum Ratings (Note 1) Operating Ratings (Note 2) Supply Input Voltage (VIN) .................................. 0V to +7V Enable Input Voltage (VEN) .................................. 0V to VIN Flag Output Voltage (VFLG) .................................. 0V to VIN Junction Temperature (TJ) ...................................... +150°C Storage Temperature ............................... –65°C to +150°C Lead Temperature (soldering, 5 sec.) ....................... 260°C ESD, Note 3 Input Voltage (VIN) ......................................... +2.7V to +6V Enable Input Voltage (VEN) .................................. 0V to VIN Flag Output Voltage (VFLG) .................................. 0V to VIN Junction Temperature (TJ) ....................... –40°C to +125°C Thermal Resistance (θJA)...................................... 235°C/W MIC5246 2 June 2000 MIC5246 Micrel Electrical Characteristics VIN = VOUT + 1V, VEN = VIN; IOUT = 100µA; TJ = 25°C, bold values indicate –40°C ≤ TJ ≤ +125°C; unless noted. Symbol Parameter Conditions Min VO Output Voltage Accuracy IOUT = 0mA –1 –2 ∆VLNR Line Regulation VIN = VOUT + 0.1V to 6V Max Units 1 2 % % 0 0.3 %/V ∆VLDR Load Regulation IOUT = 0.1mA to 150mA, Note 4 2 3 % VIN – VOUT Dropout Voltage, Note 5 IOUT = 100µA 1.5 5 mV IOUT = 50mA 50 85 mV IOUT = 100mA 100 150 mV IOUT = 150mA 150 200 250 mV mV –0.3 Typical IQ Quiescent Current VEN ≤ 0.4V (shutdown) 0.2 1 µA IGND Ground Pin Current, Note 6 IOUT = 0mA 85 150 µA IOUT = 150mA 85 150 µA 50 dB 300 mA PSRR Power Supply Rejection f = 120Hz, COUT = 10µF ILIM Current Limit VOUT = 0V VIL Enable Input Logic-Low Voltage VIN = 2.7V to 5.5V, regulator shutdown VIH Enable Input Logic-High Voltage VIN = 2.7V to 5.5V, regulator enabled IEN Enable Input Current 160 Enable Input 0.8 1.6 0.4 V 1 V VIL ≤ 0.4V 0.01 µA VIH ≥ 1.6V 0.01 µA 500 Ω Thermal Shutdown Temperature 150 °C Thermal Shutdown Hysteresis 10 °C Shutdown Resistance Discharge Thermal Protection Error Flag Low Threshold High Threshold % of VOUT (Flag ON) % of VOUT (Flag OFF) VOL Output Logic-Low Voltage IL = 100µA, fault condition 0.02 IFL Flag Leakage Current flag off, VFLG = 6V 0.01 VFLG 90 96 % % 0.4 V µA Note 1. Exceeding the absolute maximum rating may damage the device. Note 2. The device is not guaranteed to function outside its operating rating. Note 3. Devices are ESD sensitive. Handling precautions recommended. Note 4. Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 0.1mA to 150mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. For outputs below 2.7V, dropout voltage is the input-to-output voltage differential with the minimum input voltage 2.7V. Minimum input operating voltage is 2.7V. Ground pin current is the regulator quiescent current. The total current drawn from the supply is the sum of the load current plus the ground pin current. The error flag is a function of the output voltage being 5% low and the detection of one of the following: overcurrent, overtemperature or dropout. See “Applications Information” section for additional information. Note 5. Note 6. Note 7. June 2000 3 MIC5246 MIC5246 Micrel Typical Characteristics Power Supply Rejection Ratio 50 50 50 40 40 40 20 10 FREQUENCY (Hz) FREQUENCY (Hz) FREQUENCY (Hz) Power Supply Rejection Ratio Ground Current vs. Output Current Ground Pin Current 100 GROUND CURRENT (µA) 50 40 30 20 10 88 86 84 82 80 0 1x106 1x105 1x104 1x103 1x10 1 0 1x102 ILOAD = 150mA GROUND CURRENT (µA) 90 60 1x106 1x10 1 1x105 ILOAD = 100mA 0 1x106 1x105 1x104 1x103 1x10 1 1x102 ILOAD= 50mA 0 1x106 1x105 1x104 1x103 1x102 1x10 1 0 20 1x104 10 ILOAD = 100µA 30 1x103 20 30 1x102 30 PSRR (dB) 60 10 PSRR (dB) Power Supply Rejection Ratio 60 PSRR (dB) PSRR (dB) Power Supply Rejection Ratio 60 80 60 40 20 Iload = 100µA 0 -40 -10 20 50 80 110 140 TEMPERATURE (°C) 1 10 100 1000 OUTPUT CURRENT (mA) FREQUENCY (Hz) Ground Pin Current Ground Pin Current GROUND CURRENT (µA) 60 40 20 ILOAD = 150mA 0 -40 80 60 40 20 ILOAD = 100µA 0 0 -10 20 50 80 110 140 TEMPERATURE (°C) Dropout Characteristics 100µA 3 150mA 2 1 1 2 3 4 VOLTAGE IN (V) 60 40 20 I 0 0 5 5 = 150mA 2 3 4 VOLTAGE IN (V) 5 250 150 100 50 0 -40 LOAD 1 Dropout Voltage 200 DROPOUT VOLTAGE (µV) VOLTAGE OUT (V) 2 3 4 VOLTAGE IN (V) 80 Dropout Voltage 4 MIC5246 1 ILOAD = 100µA -10 20 50 80 110 140 TEMPERATURE (°C) 4 DROPOUT VOLTAGE (µV) GROUND CURRENT (µA) 80 100 GROUND CURRENT (µA) 100 100 0 0 Ground Pin Current 200 150 100 50 0 -40 ILOAD = 150mA -10 20 50 80 110 140 TEMPERATURE (°C) June 2000 MIC5246 Micrel Typical Characteristics June 2000 Output Voltage vs. Temperature 3.40 OUTPUT VOLTAGE (V) SHORT CIRCUIT CURRENT (mA) Short Circuit Current vs. Temperature 400 300 200 100 0 -40 VOUT = 0V 3.36 3.32 3.28 3.24 3.20 -40 -10 20 50 80 110 140 TEMPERATURE (°C) 5 -10 20 50 80 110 140 TEMPERATURE (°C) MIC5246 MIC5246 Micrel Block Diagrams IN EN Reference Voltage Startup/ Shutdown Control Quickstart PULL UP Thermal Sensor FAULT Error Amplifier Undervoltage Lockout Current Amplifier ACTIVE SHUTDOWN OUT PULL DOWN Out of Regulation Detection FLG Overcurrent Dropout Detection GND MIC5246 6 June 2000 MIC5246 Micrel input without using a pull-down capacitor, then there can be a glitch on the error flag upon start up of the device. This is due to the response time of the error flag circuit as the device starts up. When the device comes out of the zero off mode current state, all the various nodes of the circuit power up before the device begins supplying full current to the output capacitor. The error flag drives low immediately and then releases after a few microseconds. The intelligent circuit that triggers an error detects the output going into current limit AND the output being low while charging the output capacitor. The error output then pulls low for the duration of the turn-on time. This glitch is filtered by putting a capacitor from the error flag to ground. The glitch does not occur if the error flag pulled up to the output. Applications Information Enable/Shutdown The MIC5246 comes with an active-high enable pin that allows the regulator to be disabled. Forcing the enable pin low disables the regulator and sends it into a “zero” off-modecurrent state. In this state, current consumed by the regulator goes nearly to zero. Forcing the enable pin high enables the output voltage. This part is CMOS and the enable pin cannot be left floating; a floating enable pin may cause an indeterminate state on the output. Input Capacitor An input capacitor is not required for stability. A 1µF input capacitor is recommended when the bulk ac supply capacitance is more than 10 inches away from the device, or when the supply is a battery. Transient Response The MIC5246 implements a unique output stage to dramatically improve transient response recovery time. The output is a totem-pole configuration with a P-channel MOSFET pass device and an N-channel MOSFET clamp. The N-channel clamp is a significantly smaller device that prevents the output voltage from overshooting when a heavy load is removed. This feature helps to speed up the transient response by significantly decreasing transient response recovery time during the transition from heavy load (100mA) to light load (85µA). Output Capacitor The MIC5246 requires an output capacitor for stability. The design requires 1µF or greater on the output to maintain stability. The capacitor can be a low-ESR ceramic chip capacitor. The MIC5246 has been designed to work specifically with the low-cost, small chip capacitors. Tantalum capacitors can also be used for improved capacitance over temperature. The value of the capacitor can be increased without bound. Active Shutdown X7R dielectric ceramic capacitors are recommended because of their temperature performance. X7R-type capacitors change capacitance by 15% over their operating temperature range and are the most stable type of ceramic capacitors. Z5U and Y5V dielectric capacitors change value by as much 50% and 60% respectively over their operating temperature ranges. To use a ceramic chip capacitor with Y5V dielectric, the value must be much higher than an X7R ceramic or a tantalum capacitor to ensure the same minimum capacitance value over the operating temperature range. Tantalum capacitors have a very stable dielectric (10% over their operating temperature range) and can also be used with this device. The MIC5246 also features an active shutdown clamp, which is an N-channel MOSFET that turns on when the device is disabled. This allows the output capacitor and load to discharge, de-energizing the load. Thermal Considerations The MIC5246 is designed to provide 150mA of continuous current in a very small package. Maximum power dissipation can be calculated based on the output current and the voltage drop across the part. To determine the maximum power dissipation of the package, use the junction-to-ambient thermal resistance of the device and the following basic equation:  TJ(max) − TA  PD(max) =   θ JA   Error Flag The error flag output is an active-low, open-drain output that drives low when a fault condition AND an undervoltage detection occurs. Internal circuitry intelligently monitors overcurrent, overtemperature and dropout conditions and ORs these outputs together to indicate some fault condition. The output of that OR gate is ANDed with an output voltage monitor that detects an undervoltage condition. That output drives the open-drain transistor to indicate a fault. This prevents chattering or inadvertent triggering of the error flag. The error flag must be pulled up using a resistor from the flag pin to either the input or the output. TJ(max) is the maximum junction temperature of the die, 125°C, and TA is the ambient operating temperature. θJA is layout dependent; Table 1 shows examples of junction-toambient thermal resistance for the MIC5246. Package SOT-23-5 (M5) θJA Recommended Minimum Footprint θJA 1" Square Copper Clad θJC 235°C/W 185°C/W 145°C/W Table 1. SOT-23-5 Thermal Resistance Error Flag Circuit The error flag circuit was designed essentially to work with a capacitor to ground to act as a power-on reset generator, signaling a power-good situation once the regulated voltage was up and/or out of a fault condition. This capacitor delays the error signal from pulling high, allowing the downstream circuits time to stabilize. When the error flag is pulled up to the June 2000 7 MIC5246 MIC5246 Micrel The actual power dissipation of the regulator circuit can be determined using the equation: Fixed Regulator Applications 47kΩ PD = (VIN – VOUT) IOUT + VIN IGND VIN Substituting PD(max) for PD and solving for the operating conditions that are critical to the application will give the maximum operating conditions for the regulator circuit. For example, when operating the MIC5246-3.0BM5 at 50°C with a minimum footprint layout, the maximum input voltage for a set output current can be determined as follows: MIC5246-x.xBM5 1 5 2 3 VOUT 1µF 4 Figure 1. Low-Noise Fixed Voltage Application  125°C − 50°C  PD(max) =    235°C/W  Figure 1 shows a standard low-noise configuration with a 47kΩ pull-up resistor from the error flag to the input voltage and a pull-down capacitor to ground for the purpose of fault indication. PD(max) = 315mW The junction-to-ambient thermal resistance for the minimum footprint is 235°C/W, from Table 1. The maximum power dissipation must not be exceeded for proper operation. Using the output voltage of 3.0V and an output current of 150mA, the maximum input voltage can be determined. Because this device is CMOS and the ground current is typically 100µA over the load range, the power dissipation contributed by the ground current is < 1% and can be ignored for this calculation. 315mW = (VIN – 3.0V) 150mA Dual-Supply Operation When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage must be diode clamped to ground. 315mW = VIN ·150mA – 450mW 810mW = VIN ·150mA VIN(max) = 5.4V Therefore, a 3.0V application at 150mA of output current can accept a maximum input voltage of 5.4V in a SOT-23-5 package. For a full discussion of heat sinking and thermal effects on voltage regulators, refer to the Regulator Thermals section of Micrel’s Designing with Low-Dropout Voltage Regulators handbook. MIC5246 8 June 2000 MIC5246 Micrel Package Information 1.90 (0.075) REF 0.95 (0.037) REF 1.75 (0.069) 1.50 (0.059) 3.00 (0.118) 2.60 (0.102) DIMENSIONS: MM (INCH) 3.02 (0.119) 2.80 (0.110) 0.50 (0.020) 0.35 (0.014) 1.30 (0.051) 0.90 (0.035) 0.20 (0.008) 0.09 (0.004) 10° 0° 0.15 (0.006) 0.00 (0.000) 0.60 (0.024) 0.10 (0.004) SOT-23-5 (M) June 2000 9 MIC5246 MIC5246 MIC5246 Micrel 10 June 2000 MIC5246 June 2000 Micrel 11 MIC5246 MIC5246 Micrel MICREL INC. 1849 FORTUNE DRIVE TEL + 1 (408) 944-0800 FAX SAN JOSE, CA 95131 + 1 (408) 944-0970 WEB USA http://www.micrel.com This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. © 2000 Micrel Incorporated MIC5246 12 June 2000