MIC5247
150 mA Low Voltage μCap Linear Regulator
Features
General Description
• Ultra-Low Noise
• Low Voltage Outputs
• Load Independent, Ultra-Low Ground Current:
85 μA
• 150 mA Output Current
• Current Limiting
• Thermal Shutdown
• Tight Load and Line Regulation
• “Zero” Off-Mode Current
• Stability with Low-ESR Capacitors
• Fast Transient Response
• Logic-Controlled Enable Input
The MIC5247 is an efficient and precise, low-voltage
CMOS linear regulator optimized for ultra-low noise
applications. The MIC5247 offers better than 1% initial
accuracy and 85 μA constant ground current over load
(typically 85 μA). The MIC5247 provides a very
low-noise output, ideal for RF applications where quiet
voltage sources are required. A noise bypass pin is
also available for further reduction of output noise.
Applications
•
•
•
•
•
•
•
•
Cellular Phones and Pagers
Cellular Accessories
Battery-Powered Equipment
Laptop, Notebook, and Palmtop Computers
PCMCIA VCC and VPP Regulation/Switching
Consumer/Personal Electronics
SMPS Post-Regulator/DC-to-DC Modules
High-Efficiency Linear Power Supplies
Designed specifically for handheld and batterypowered devices, the MIC5247 provides a logic
compatible enable pin. When disabled, power
consumption drops nearly to zero. The MIC5247 also
works with low-ESR ceramic capacitors, reducing
the amount of board space necessary for power
applications, critical in handheld wireless devices.
Key features include current limit, thermal shutdown, a
push-pull output for faster transient response, and an
active clamp to speed up device turnoff. Available in
the 6-lead 2 mm × 2 mm VDFN package and the 5-lead
SOT-23 package, the MIC5247 also offers a range of
fixed output voltages.
Package Types
MIC5247
-x.xYM5/YD5
5-Lead SOT-23
(Top View)
-x.xYML
6-Lead VDFN
(Top View)
2021 Microchip Technology Inc. and its subsidiaries
DS20006596A-page 1
MIC5247
Typical Application Circuits
Ultra-Low-Noise Regulator Application
MIC5247-x.xYM5
MIC5247-x.xYML
Functional Block Diagram
DS20006596A-page 2
2021 Microchip Technology Inc. and its subsidiaries
MIC5247
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Supply Input Voltage (VIN) ................................................................................................................................ 0V to +7V
Enable Input Voltage (VEN) ... .............................................................................................................................0V to VIN
ESD Rating ............................................................................................................................................................Note 1
Operating Ratings ‡
Input Voltage (VIN) ....................................................................................................................................... +2.7V to +6V
Enable Input Voltage (VEN) ................................................................................................................................0V to VIN
† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
‡ Notice: The device is not guaranteed to function outside its operating ratings.
Note 1: Devices are ESD sensitive. Handling precautions recommended.
ELECTRICAL CHARACTERISTICS
VIN = VOUT + 1.0V; VIN = VEN; IOUT = 100 μA; TJ = 25°C, bold values valid for –40°C ≤ TJ ≤ +125°C; unless noted.
(See Note 1)
Parameter
Output Voltage Accuracy
Line Regulation
Load Regulation
Dropout Voltage
Quiescent Current
Ground Pin Current (Note 4)
Power Supply Rejection
Symbol
Min.
Typ.
Max.
–1
—
+1
–2
—
+2
–0.3
—
+0.3
%/V
—
2
3
%
IOUT = 0.1 mA to 150 mA
(Note 2)
—
3
4
%
IOUT = 0.1 mA to 150 mA,
VOUT = 1.5V or 1.6V
VIN – VOUT
—
150
—
mV
IOUT = 150 mA (Note 3)
IQ
—
0.2
1
μA
VEN ≤ 0.4V (shutdown)
—
85
150
μA
IOUT = 0 mA
—
85
150
μA
IOUT = 150 mA
VO
ΔVLNR
ΔVLDR
IGND
Units
%
Conditions
IOUT = 0 mA
VIN = 2.7V to 6V
PSRR
—
50
—
dB
f ≤ 1 kHz
ILIM
160
300
—
mA
VOUT = 0V
en
—
30
—
μVrms
Enable Input Logic-Low
Voltage
VIL
—
0.8
0.4
V
VIN = 2.7V to 5.5V, regulator
shutdown
Enable Input Logic-High
Voltage
VIH
1.6
1
—
V
VIN = 2.7V to 5.5V, regulator
enabled
Enable Input Current
IEN
—
0.01
—
μA
VIL ≤ 0.4V
—
0.01
—
μA
VIH ≥ 1.6V
Shutdown Resistance
Discharge
—
—
500
—
Ω
—
Current Limit
Output Voltage Noise
COUT = 10 μF, CBYP = 0.01 μF,
f = 10 Hz to 100 kHz
Enable Input
2021 Microchip Technology Inc. and its subsidiaries
DS20006596A-page 3
MIC5247
ELECTRICAL CHARACTERISTICS
VIN = VOUT + 1.0V; VIN = VEN; IOUT = 100 μA; TJ = 25°C, bold values valid for –40°C ≤ TJ ≤ +125°C; unless noted.
(See Note 1)
Parameter
Symbol
Min.
Typ.
Max.
Units
Conditions
Thermal Shutdown
Temperature
—
—
+150
—
°C
—
Thermal Shutdown
Hysteresis
—
—
+10
—
°C
—
Thermal Protection
Note 1:
2:
3:
4:
Specification for packaged product only.
Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are
tested for load regulation in the load range from 0.1 mA to 150 mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification.
Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its
nominal value measured a 1V differential. For outputs below 2.7V, dropout voltage is the input-to-output
voltage differential with the minimum input voltage 2.7V. Minimum input operating voltage is 2.7V.
Ground pin current is the regulator quiescent current plus pass transistor base current. The total current
drawn from the supply is the sum of the load current plus the ground pin current.
TEMPERATURE SPECIFICATIONS (Note 1)
Parameters
Sym.
Min.
Typ.
Max.
Units
Operating Junction Temperature
Range
TJ
–40
—
+125
°C
Maximum Junction Temperature
Conditions
Temperature Ranges
—
TJ(MAX)
—
—
+150
°C
—
Lead Temperature
—
—
—
+260
°C
Soldering, 5 seconds
Storage Temperature
TS
–65
—
+150
°C
—
Thermal Resistance, 5-Lead SOT-23
θJA
—
+235
—
°C/W
—
Thermal Resistance, 6-Lead VDFN
θJA
—
+90
—
°C/W
—
Package Thermal Resistance
Note 1:
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, JA). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum rating. Sustained junction temperatures above that maximum can impact device reliability.
DS20006596A-page 4
2021 Microchip Technology Inc. and its subsidiaries
MIC5247
2.0
Note:
TYPICAL PERFORMANCE CURVES
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
FIGURE 2-1:
Ratio.
Power Supply Rejection
FIGURE 2-4:
Ratio.
Power Supply Rejection
FIGURE 2-2:
Ratio.
Power Supply Rejection
FIGURE 2-5:
Noise Performance.
FIGURE 2-3:
Ratio.
Power Supply Rejection
FIGURE 2-6:
Current.
Ground Current vs. Output
2021 Microchip Technology Inc. and its subsidiaries
DS20006596A-page 5
MIC5247
FIGURE 2-7:
Ground Pin Current.
FIGURE 2-10:
Ground Pin Current.
FIGURE 2-8:
Ground Pin Current.
FIGURE 2-11:
Dropout Characteristics.
FIGURE 2-9:
Ground Pin Current.
FIGURE 2-12:
Temperature.
Short Circuit Current vs.
DS20006596A-page 6
2021 Microchip Technology Inc. and its subsidiaries
MIC5247
FIGURE 2-13:
Temperature.
Output Voltage vs.
FIGURE 2-14:
Capacitor.
Turn-On Time vs. Bypass
FIGURE 2-15:
Load Transient Response.
2021 Microchip Technology Inc. and its subsidiaries
FIGURE 2-16:
Line Transient Response.
DS20006596A-page 7
MIC5247
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
Pin Number Pin Number
5-Lead
6-Lead
SOT-23
VDFN
Pin Name
1
3
IN
2
2
GND
3
1
EN
4
6
BYP
5
4
OUT
—
5
NC
—
EP
GND
DS20006596A-page 8
Description
Supply Input.
Ground.
Enable/Shutdown (Input): CMOS-compatible input. Logic high = enable;
logic low = shutdown. Do not leave open.
Reference Bypass: Connect external 0.01 μF capacitor to GND to reduce
output noise. May be left open.
Regulator Output.
No Internal Connection.
Ground. Internally connected to the exposed pad. Connect to ground pin.
2021 Microchip Technology Inc. and its subsidiaries
MIC5247
4.0
APPLICATION INFORMATION
4.1
Enable/Shutdown
The MIC5247 comes with an active-high enable pin
that can disable the regulator. Forcing the enable pin
low disables the regulator and sends it into a “zero”
off-mode-current state. In this state, current consumed
by the regulator goes nearly to zero. Forcing the enable
pin high enables the output voltage.
This part is CMOS and the enable pin cannot be left
floating, because a floating enable pin may cause an
indeterminate state on the output.
4.2
Input Capacitor
An input capacitor is not required for stability. A 1 μF
input capacitor is recommended when the bulk AC
supply capacitance is more than 10 inches away from
the device or when the supply is a battery.
4.3
4.6
Active Shutdown
The MIC5247 also features an active shutdown clamp,
which is an N-Channel MOSFET that turns on when the
device is disabled. This allows the output capacitor and
load to discharge, de-energizing the load.
4.7
Thermal Considerations
The MIC5247 is designed to provide 150 mA of
continuous current in a very small package. Maximum
power dissipation can be calculated based on the
output current and the voltage drop across the part. To
determine the maximum power dissipation of the
package, use the junction-to-ambient thermal
resistance of the device and the following basic
equation:
EQUATION 4-1:
Output Capacitor
T J MAX – T A
P D = --------------------------------
JA
The MIC5247 requires an output capacitor for stability.
The design requires 1 μF or greater on the output to
maintain stability. The capacitor can be a low-ESR
ceramic chip capacitor.
The MIC5247 has been designed to work specifically
with low-cost, small chip capacitors. Tantalum
capacitors can also be used for improved capacitance
over temperature. The value of the capacitor can be
increased without bound.
TJ(MAX) is the maximum junction temperature of the
die, 125°C, and TA is the ambient operating
temperature. θJA is layout dependent; Table 4-1 shows
examples of junction-to-ambient thermal resistance for
the MIC5247.
4.4
TABLE 4-1:
Bypass Capacitor
A capacitor can be placed from the noise bypass pin to
ground to reduce output voltage noise. The capacitor
bypasses the internal reference. A 0.01 μF capacitor is
recommended for applications that require low-noise
outputs.
The bypass capacitor can be increased without bound,
further reducing noise and improving PSRR. Turn-on
time remains constant with respect to bypass
capacitance. Refer to Figure 2-14.
4.5
Transient Response
The MIC5247 implements a unique output stage to
dramatically improve transient response recovery time.
The output is a push-pull configuration with a
P-Channel MOSFET pass device and an N-Channel
MOSFET clamp. The N-Channel clamp is a
significantly smaller device that prevents the output
voltage from overshooting when a heavy load is
removed.
Package
5-Lead
SOT-23
5-LEAD SOT-23 THERMAL
RESISTANCE
θJA
Recommended
Minimum
Footprint
θJA 1”
Square
Copper
Clad
θJC
235°C/W
185°C/W
145°C/W
The actual power dissipation of the regulator circuit can
be determined using Figure 4-2:
EQUATION 4-2:
P D = V IN – V OUT I OUT + V IN I GND
This feature helps to speed up the transient response
by significantly decreasing transient response recovery
time during the transition from heavy load (100 mA) to
light load (85 μA).
2021 Microchip Technology Inc. and its subsidiaries
DS20006596A-page 9
MIC5247
Substituting PD(MAX) for PD and solving for the
operating conditions that are critical to the application
will give the maximum operating conditions for the
regulator circuit. For example, when operating the
MIC5247-2.4YM5 at room temperature with a minimum
footprint layout, the maximum input voltage for a set
output current can be determined as follows:
4.8
Fixed Regulator Applications
EQUATION 4-3:
125C – 25C
P D MAX = -----------------------------------
235C/W
Where:
PD(MAX) = 425 mW
The junction-to-ambient thermal resistance for the
minimum footprint is 235°C/W, from Table 4-1. The
maximum power dissipation must not be exceeded for
proper operation. Using the output voltage of 2.4V and
an output current of 150 mA, the maximum input
voltage can be determined. Because this device is
CMOS and the ground current is typically 100 μA over
the load range, the power dissipation contributed by the
ground current is < 1% and can be ignored for this
calculation.
FIGURE 4-1:
MIC5247-x.xYM5,
Ultra-Low-Noise Fixed Voltage Application.
Figure 4-1 includes a 0.01 μF capacitor for low-noise
operation and shows EN (pin 3) connected to IN (pin 1)
for an application where enable/shutdown is not
required. COUT = 1 μF minimum.
EQUATION 4-4:
425mW = V IN – 2.4V 150mA
425mW = V IN 150mA – 360mW
785mW = V IN 150mA
V IN MAX = 5.2V
FIGURE 4-2:
MIC5247-x.xYM5,
Low-Noise Fixed Voltage Application.
Figure 4-2 is an example of a low-noise configuration
where CBYP is not required. COUT = 1 μF minimum.
Therefore, a 2.4V application at 150mA of output
current can accept a maximum input voltage of 5.2V in
a 5-Lead SOT-23 package. For a full discussion of heat
sinking and thermal effects on voltage regulators, refer
to the “Regulator Thermals” section of Micrel’s
Designing with Low-Dropout Voltage Regulators
handbook.
DS20006596A-page 10
2021 Microchip Technology Inc. and its subsidiaries
MIC5247
5.0
PACKAGING INFORMATION
5.1
Package Marking Information
5-Lead SOT-23*
XXXX
NNN
NU20
723
Example
6-Lead VDFN*
XXX
XXX
TABLE 5-1:
Example
U16
420
ORDERING INFORMATION
Pb Free
Marking
Voltage
MIC5247-1.5YM5
LU15
1.5V
MIC5247-1.6YM5
LU16
MIC5247-1.8YM5
LU18
MIC5247-1.85YM5
MIC5247-2.0YM5
MIC5247-2.4YM5
LU24
Legend: XX...X
Y
YY
WW
NNN
e3
*
Pb Free
Marking
Voltage
MIC5247-1.8YD5
NU18
1.8V
1.6V
MIC5247-2.0YD5
NU20
2.0V
1.8V
MIC5247-1.5YML
U15
1.5V
LU1J
1.85V
MIC5247-1.6YML
U16
1.6V
LU20
2.0V
MIC5247-1.8YML
U18
1.8V
2.4V
MIC5247-1.85YML
U1J
1.85V
Product code or customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle
mark).
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information. Package may or may not include
the corporate logo.
Underbar (_) and/or Overbar (‾) symbol may not be to scale.
2021 Microchip Technology Inc. and its subsidiaries
DS20006596A-page 11
MIC5247
6-Lead VDFN Package Outline and Recommended Land Pattern
6-Lead Very Thin Plastic Dual Flat, No Lead Package (JDA) - 2x2 mm Body [VDFN]
Micrel Legacy Package
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
A
N
B
4
(DATUM A)
(DATUM B)
E
NOTE 1
2X
0.05 C
1
3
2X
0.05 C
TOP VIEW
0.10 C
C
A1
A
SEATING
PLANE
6X
(A3)
0.05 C
SIDE VIEW
0.10
C A B
D2
1
3
NOTE 1
0.10
C A B
E2
K
L
N
4
6X b
e
BOTTOM VIEW
0.10
0.05
C A B
C
Microchip Technology Drawing C04-1016A Sheet 1 of 2
© 2017 Microchip Technology Incorporated
DS20006596A-page 12
2021 Microchip Technology Inc. and its subsidiaries
MIC5247
6-Lead Very Thin Plastic Dual Flat, No Lead Package (JDA) - 2x2 mm Body [VDFN]
Micrel Legacy Package
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Notes:
Units
Dimension Limits
Number of Terminals
N
e
Pitch
A
Overall Height
Standoff
A1
Terminal Thickness
A3
Overall Length
D
Exposed Pad Length
D2
Overall Width
E
Exposed Pad Width
E2
b
Terminal Width
Terminal Length
L
K
Terminal-to-Exposed-Pad
MIN
0.80
0.00
1.35
0.75
0.20
0.30
0.20
MILLIMETERS
NOM
6
0.65 BSC
0.85
0.02
0.203 REF
2.00 BSC
1.40
2.00 BSC
0.80
0.25
0.35
-
MAX
0.90
0.05
1.45
0.85
0.30
0.40
-
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Package is saw singulated
3. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-1016A Sheet 2 of 2
© 2017 Microchip Technology Incorporated
2021 Microchip Technology Inc. and its subsidiaries
DS20006596A-page 13
MIC5247
6-Lead Very Thin Plastic Dual Flat, No Lead Package (JDA) - 2x2 mm Body [VDFN]
Micrel Legacy Package
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
X2
6
ØV
C1 Y2
G1
Y1
1
2
SILK SCREEN
X1
E
RECOMMENDED LAND PATTERN
Units
Dimension Limits
Contact Pitch
E
X2
Optional Center Pad Width
Optional Center Pad Length
Y2
Contact Pad Spacing
C1
Contact Pad Width (X6)
X1
Contact Pad Length (X6)
Y1
Contact Pad to Center Pad (X6)
G1
Thermal Via Diameter
V
MIN
MILLIMETERS
NOM
0.65 BSC
MAX
0.85
1.45
2.00
0.30
0.75
0.20
0.27
0.30
0.33
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
2. For best soldering results, thermal vias, if used, should be filled or tented to avoid solder loss during
reflow process
Microchip Technology Drawing C04-21016A
© 2017 Microchip Technology Incorporated
DS20006596A-page 14
2021 Microchip Technology Inc. and its subsidiaries
MIC5247
5-Lead SOT-23 Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
2021 Microchip Technology Inc. and its subsidiaries
DS20006596A-page 15
MIC5247
NOTES:
DS20006596A-page 16
2021 Microchip Technology Inc. and its subsidiaries
MIC5247
APPENDIX A:
REVISION HISTORY
Revision A (October 2021)
• Converted Micrel document MIC5247 to Microchip data sheet DS20006596A.
• Minor text changes throughout.
2021 Microchip Technology Inc. and its subsidiaries
DS20006596A-page 17
MIC5247
NOTES:
DS20006596A-page 18
2021 Microchip Technology Inc. and its subsidiaries
MIC5247
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office.
PART No.
-X.X
X
XX
-XX
Device
Output
Voltage
Junction Temp.
Range
Package
Media Type
Device:
Output Voltage:
MIC5247:
-1.5
-1.6
-1.8
-1.85
-2.0
-2.4
=
=
=
=
=
=
150mA Low Voltage μCap Linear
Regulator
1.5V (M5 and ML option only)
1.6V (M5 and ML option only)
1.8V
1.85V (M5 and ML option only)
2.0V (M5 and D5 option only)
2.4V (M5 option only)
Junction
Temperature
Range:
Y
=
–40°C to +125°C
Package:
M5
D5
ML
=
=
=
5-Lead SOT-23
5-Lead SOT-23
6-Lead VDFN
Media Type:
-TX
-TX
-TR
-TR
-TR
=
=
=
=
=
3000/Reverse Reel (M5 option only)
3000/Reel (D5 option only)
3000/Reverse Reel (M5 option only)
3000/Reel (D5 option only)
5000/Reel (ML option only)
2021 Microchip Technology Inc. and its subsidiaries
Examples:
a) MIC5247-1.6YM5-TX:
MIC5247, 1.6V Output
Voltage, –40°C to +125°C
Temp. Range, 5-Lead
SOT-23, 3000/Reverse Reel
b) MIC5247-1.5YM5-TR:
MIC5247, 1.5V Output
Voltage, –40°C to +125°C
Temp. Range, 5-Lead
SOT-23, 3000/Reverse Reel
c) MIC5247-2.0YD5-TX:
MIC5247, 2.0V Output
Voltage, –40°C to +125°C
Temp. Range, 5-Lead
SOT-23, 3000/Reel
d) MIC5247-1.8YD5-TR:
MIC5247, 1.8V Output
Voltage, –40°C to +125°C
Temp. Range, 5-Lead
SOT-23, 3000/Reel
e) MIC5247-1.85YML-TR: MIC5247, 1.85V Output
Voltage, –40°C to +125°C
Temp. Range, 6-Lead VDFN,
5000/Reel
Note 1:
Tape and Reel identifier only appears in the
catalog part number description. This identifier is
used for ordering purposes and is not printed on
the device package. Check with your Microchip
Sales Office for package availability with the
Tape and Reel option.
DS20006596A-page 19
MIC5247
NOTES:
DS20006596A-page 20
2021 Microchip Technology Inc. and its subsidiaries
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specifications contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is secure when used in the intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods being used in attempts to breach the code protection features of the Microchip
devices. We believe that these methods require using the Microchip products in a manner outside the operating specifications
contained in Microchip's Data Sheets. Attempts to breach these code protection features, most likely, cannot be accomplished
without violating Microchip's intellectual property rights.
•
Microchip is willing to work with any customer who is concerned about the integrity of its code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not
mean that we are guaranteeing the product is "unbreakable." Code protection is constantly evolving. We at Microchip are
committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection
feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or
other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication is provided for the sole
purpose of designing with and using Microchip products. Information regarding device applications and the like is provided
only for your convenience and may be superseded by updates.
It is your responsibility to ensure that your application meets
with your specifications.
THIS INFORMATION IS PROVIDED BY MICROCHIP "AS IS".
MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED,
WRITTEN OR ORAL, STATUTORY OR OTHERWISE,
RELATED TO THE INFORMATION INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A
PARTICULAR PURPOSE OR WARRANTIES RELATED TO
ITS CONDITION, QUALITY, OR PERFORMANCE.
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND
WHATSOEVER RELATED TO THE INFORMATION OR ITS
USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS
BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES
ARE FORESEEABLE. TO THE FULLEST EXTENT
ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON
ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION
OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF
ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP
FOR THE INFORMATION. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and
the buyer agrees to defend, indemnify and hold harmless
Microchip from any and all damages, claims, suits, or expenses
resulting from such use. No licenses are conveyed, implicitly or
otherwise, under any Microchip intellectual property rights
unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec,
AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, chipKIT,
chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex,
flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck,
LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi,
Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer,
PackeTime, PIC, picoPower, PICSTART, PIC32 logo, PolarFire,
Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST,
SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon,
TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered
trademarks of Microchip Technology Incorporated in the U.S.A. and
other countries.
AgileSwitch, APT, ClockWorks, The Embedded Control Solutions
Company, EtherSynch, FlashTec, Hyper Speed Control, HyperLight
Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3,
Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, QuietWire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub,
TimePictra, TimeProvider, WinPath, and ZL are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky,
BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive,
CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net,
Dynamic Average Matching, DAM, ECAN, Espresso T1S,
EtherGREEN, IdealBridge, In-Circuit Serial Programming, ICSP,
INICnet, Intelligent Paralleling, Inter-Chip Connectivity,
JitterBlocker, maxCrypto, maxView, memBrain, Mindi, MiWi,
MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK,
NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net,
PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE,
Ripple Blocker, RTAX, RTG4, SAM-ICE, Serial Quad I/O,
simpleMAP, SimpliPHY, SmartBuffer, SMART-I.S., storClad, SQI,
SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total
Endurance, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY,
ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks
of Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage
Technology, and Symmcom are registered trademarks of Microchip
Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany
II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in
other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2021, Microchip Technology Incorporated, All Rights Reserved.
For information regarding Microchip’s Quality Management Systems,
please visit www.microchip.com/quality.
2021 Microchip Technology Inc. and its subsidiaries
ISBN:978-1-5224-9158-3
DS20006596A-page 21
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
DS20006596A-page 22
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Denmark - Copenhagen
Tel: 45-4485-5910
Fax: 45-4485-2829
Finland - Espoo
Tel: 358-9-4520-820
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-72400
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7288-4388
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
2021 Microchip Technology Inc. and its subsidiaries
09/14/21
工商网监
湘ICP备2023018690号
