MIC5891
8-Bit Serial-Input Latched Source Driver
Features
General Description
• High-Voltage, High-Current Outputs
• Output Transient Protection Diodes
• CMOS-, PMOS-, NMOS-, and TTL-Compatible
Inputs
• 5 MHz Typical Data Input Rate
• Low-Power CMOS Latches
The MIC5891 latched driver is a high-voltage,
high-current integrated circuit comprised of eight
CMOS data latches, CMOS control circuitry for the
common STROBE and OUTPUT ENABLE, and bipolar
Darlington transistor drivers for each latch.
Applications
•
•
•
•
Alphanumeric and Bar Graph Displays
LED and Incandescent Displays
Relay and Solenoid Drivers
Other High-Power Loads
Package Type
1
CLOCK
2
The MIC5891 will typically operate at 5 MHz with a 5V
logic supply.
The CMOS inputs are compatible with standard
CMOS, PMOS, and NMOS logic levels. TTL circuits
may be used with appropriate pull-up resistors to
ensure a proper logic-high input.
A CMOS serial data output allows additional drivers to
be cascaded when more than 8 bits are required.
MIC5891
16-PIN PDIP OR SOICW
GROUND
Bipolar/MOS construction provides extremely low
power latches with maximum interface flexibility.
16 SERIAL
DATA OUT
SHIFT
VDD 15 LOGIC SUPPLY
REGISTER
SERIAL
DATA IN
3
STROBE
4
OUT1
5
12 OUT8
OUT2
6
11 OUT7
OUT3
7
10 OUT6
OUT4
8
LATCHES
OE
OUTPUT
14
ENABLE
VBB
13 LOAD SUPPLY
9
2016 - 2022 Microchip Technology Inc.
The MIC5891 has open-emitter outputs with
suppression diodes for protection against inductive
load transients. The output transistors are capable of
sourcing 500 mA and will sustain at least 35V in the
on-state.
Simultaneous operation of all drivers at maximum rated
current requires a reduction in duty cycle due to
package power limitations. Outputs may be paralleled
for higher load current capability.
The MIC5891 is available in a 16-pin plastic DIP
package (N) and 16-pin wide SOIC package (WM).
OUT5
DS20005638B-page 1
MIC5891
Functional Diagram
MIC5891
16-PIN PDIP OR SOICW
CLOCK
SERIAL
DATA IN
8-BIT SERIAL PARALLEL SHIFT REGISTER
STROBE
LATCHES
SERIAL
DATA OUT
GROUND
OUTPUT
ENABLE
MOS
BIPOLAR
OUT1 OUT2
DS20005638B-page 2
OUT3 OUT4 OUT5
OUT6 OUT7 OUT8
2016 - 2022 Microchip Technology Inc.
MIC5891
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings † (Note 1, Note 2, Note 3)
Output Voltage (VOUT) ..............................................................................................................................................+50V
Logic Supply Voltage Range (VDD) ............................................................................................................ +4.5V to +15V
Load Supply Voltage Range (VBB)............................................................................................................. +5.0V to +50V
Input Voltage Range (VIN).............................................................................................................. –0.3V to (VDD + 0.3V)
Continuous Collector Current (IC) .........................................................................................................................500 mA
Package Power Dissipation ...................................................................................................................... See Figure 2-1
† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Note 1: TA = +25°C.
2: Derate at the rate of 20 mW/°C above TA = +25°C.
3: Microchip CMOS devices have input-static protection, but are susceptible to damage when exposed to
extremely high static electrical charges.
TABLE 1-1:
ALLOWABLE DUTY CYCLES
Maximum Allowable Duty Cycles at a TA of:
Number of Outputs ON at
IOUT = –200 mA
+50°C
+60°C
+70°C
8
53%
47%
41%
7
60%
54%
48%
6
70%
64%
56%
5
83%
75%
67%
4
100%
94%
84%
3
100%
100%
100%
2
100%
100%
100%
1
100%
100%
100%
2016 - 2022 Microchip Technology Inc.
DS20005638B-page 3
MIC5891
Electrical Characteristics
Electrical Characteristics: VBB = 50V, VDD = 5V to 12V; TA = 25°C, unless noted. (Note 1).
Parameters
Output Leakage Current
Output Saturation Voltage
Output Sustaining Voltage
Input Voltage
Input Current
Input Impedance
Maximum Clock Frequency
Sym.
ICEX
VCE(SAT)
VCE(SUS)
VIN(1)
VIN(0)
IIN(1)
ZIN
fc
Min.
Typ.
Max.
Units
Conditions
—
—
–50
µA
TA = +25°C
—
—
–100
µA
TA = +85°C
—
—
2.3
V
IOUT = –100 mA, TA = +85°C
—
—
2.4
V
IOUT = –225 mA, TA = +85°C
—
—
2.5
V
IOUT = –350 mA, TA = +85°C
35
—
—
V
IOUT = –350 mA, L = 2 mH
3.5
—
VDD+0.3
V
VDD = 5.0V
10.5
—
VDD+0.3
V
VDD = 12V
VSS–0.3
—
0.8
V
VDD = 5.0V to 12V
—
—
120
µA
VDD = VIN = 5.0V
—
—
240
µA
VDD = 12V
100
—
—
kΩ
VDD = 5.0V
50
—
—
kΩ
VDD = 12V
3.3
—
—
MHz
—
—
—
20
kΩ
VDD = 5.0V
—
—
6.0
kΩ
VDD = 12V
Serial Data Output Resistance
ROUT
Turn-On Delay
tPLH
—
—
2.0
µs
Output Enable to Output,
IOUT = –350 mA
Turn-Off Delay
tPHL
—
—
10
µs
Output Enable to Output,
IOUT = –350 mA
—
—
10
mA
All outputs on, all outputs open
—
—
200
µA
All outputs off
—
—
100
µA
VDD = 5V, all outputs off,
inputs = 0V
—
—
200
µA
VDD = 12V, all outputs off,
inputs = 0V
—
—
1.0
mA
VDD = 5V, one output on,
inputs = 0V
—
—
3.0
mA
VDD = 12V, one output on,
inputs = 0V
—
—
50
µA
TA = +25°C; Max. VBB
—
—
100
µA
TA = +85°C; Max. VBB
—
—
2.0
V
IF = 350 mA; VBB open
IBB
Supply Current
IDD
Diode Leakage Current
IH
Diode Forward Voltage
VF
Note 1:
2:
3:
Specification for packaged product only.
Positive (negative) current is defined as going into (coming out of) the specified device pin.
Operation of these devices with standard TTL may require the use of appropriate pull-up resistors.
DS20005638B-page 4
2016 - 2022 Microchip Technology Inc.
MIC5891
TEMPERATURE SPECIFICATIONS
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Operating Temperature Range
TA
–40
—
+85
°C
Note 1
Storage Temperature Range
TS
–65
—
+150
°C
—
Temperature Ranges
Note 1:
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, JA). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
Typical Circuits
V BB
V DD
IN
V OUT
FIGURE 1-1:
Typical Input Circuit
2016 - 2022 Microchip Technology Inc.
FIGURE 1-2:
Typical Output Circuit.
DS20005638B-page 5
MIC5891
2.0
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
PACKAGE POWER DISSIPATION (W)
Note:
TYPICAL PERFORMANCE CURVES
2.5
2
PDIP
șJA = 60°C/W
1.5
1
0.5
CerDIP
șJA = 90°C/W
0
25
50
75
100 125 150
AMBIENT TEMPERATURE (°C)
FIGURE 2-1:
Allowable Package Power
Dissipation vs. Temperature.
DS20005638B-page 6
2016 - 2022 Microchip Technology Inc.
MIC5891
3.0
TIMING CONDITIONS
The descriptions of the timing conditions are listed below Figure 3-1.
CLOCK
A
B
D
DATA IN
E
F
C
STROBE
OUTPUT
ENABLE
G
OUT N
H
FIGURE 3-1:
TABLE 3-1:
I
Timing Conditions.
TIMING CONDITIONS PARAMETERS
VDD = 5.0V, Logic levels are VDD and ground.
Reference
Parameter
Value
A
Minimum data active time before clock pulse (data set-up time)
75 ns
B
Minimum data active time after clock pulse (data hold time)
75 ns
C
Minimum data pulse width
150 ns
D
Minimum clock pulse width
150 ns
E
Minimum time between clock activation and strobe
300 ns
F
Minimum strobe pulse width
100 ns
G
Typical time between strobe activation and output transition
H
Turn-off delay
See Electrical Characteristics
I
Turn-on delay
See Electrical Characteristics
TABLE 3-2:
Serial
Data
Input
TRUTH TABLE
Clock
Input
Shift Register
Contents
I1 I2 I3 ... IN-1 IN
Serial
Data
Output
Strobe
Input
Latch Contents
—
—
I1 I2 I3 ... IN-1 IN
H
H R1 R2 ... RN-2 RN-1
RN-1
L
L R1 R2 ... RN-2 RN-1
RN-1
X
R1 R2 R3 ... RN-1 RN
RN
X X X ... X X
X
L
R1 R2 R3 ... RN-1 RN
P1 P2 P3 ... PN-1 PN
PN
H
P1 P2 P3 ... PN-1 PN
—
1.0 µs
—
Output
Enable
Output Content
—
—
L
P1 P2 P3 ... PN-1 PN
I1 I2 I3 ... IN-1 IN
—
—
—
X X X ... X X
H
L = Low Logic Level, H = High Logic Level, X = Irrelevant, P = Present State, R = Previous State.
2016 - 2022 Microchip Technology Inc.
L L L ... L L
DS20005638B-page 7
MIC5891
4.0
APPLICATION INFORMATION
Serial data present at the input is transferred into the
shift register on the rising edge of the CLOCK input
pulse. Additional CLOCK pulses shift data information
towards the SERIAL DATA OUTPUT. The serial data
must appear at the input prior to the rising edge of the
CLOCK input waveform.
The 8 bits present in the shift register are transferred to
the respective latches when the STROBE is high
(serial-to-parallel conversion). The latches will continue
to accept new data as long as the STROBE is held
high. Most applications where the latching feature is
not used (STROBE tied high) require the OUTPUT
ENABLE input to be high during serial data entry.
Outputs are active (controlled by the latch state) when
the OUTPUT ENABLE is low. All outputs are low
(disabled) when the OUTPUT ENABLE is high.
OUTPUT ENABLE does not affect the data in the shift
register or latch.
DS20005638B-page 8
2016 - 2022 Microchip Technology Inc.
MIC5891
5.0
PACKAGING INFORMATION
5.1
Package Marking Information
16-Pin PDIP*
XXXXXX
XXXXXXXXX
WNNN
16-Pin SOICW*
XXXXXX
XXXXXXXXXX
WNNN
Legend: XX...X
Y
YY
WW
NNN
e3
*
Example
MICREL
MIC5891YN
1312
Example
MICREL
MIC5891YWM
1632
Product code or customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle
mark).
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information. Package may or may not include
the corporate logo.
Underbar (_) and/or Overbar (‾) symbol may not be to scale.
Note:
If the full seven-character YYWWNNN code cannot fit on the package, the following truncated codes
are used based on the available marking space:
6 Characters = YWWNNN; 5 Characters = WWNNN; 4 Characters = WNNN; 3 Characters = NNN;
2 Characters = NN; 1 Character = N
2016 - 2022 Microchip Technology Inc.
DS20005638B-page 9
MIC5891
16-Lead PDIP Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
DS20005638B-page 10
2016 - 2022 Microchip Technology Inc.
MIC5891
16-Lead SOICW Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
2016 - 2022 Microchip Technology Inc.
DS20005638B-page 11
MIC5891
NOTES:
DS20005638B-page 12
2016 - 2022 Microchip Technology Inc.
MIC5891
APPENDIX A:
REVISION HISTORY
Revision A (October 2016)
• Converted Micrel document MIC5891 to Microchip data sheet DS20005638B.
• Minor text changes throughout.
• Operating temperature range corrected in the
Temperature Specifications section.
• Maximum Saturation Voltage values updated in
Table .
• First Input Current maximum value updated in
Table .
Revision B (February 2022)
• Corrected the device marking specification in
Section 5.1, Package Marking Information.
2016 - 2022 Microchip Technology Inc.
DS20005638B-page 13
MIC5891
NOTES:
DS20005638B-page 14
2016 - 2022 Microchip Technology Inc.
MIC5891
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office.
PART NO.
X
XX
–
X.X
Examples:
a) MIC5891YN:
8-Bit Serial-Input Latched
Source Driver, –40°C to +85°C
Junction Temperature Range,
16-Lead PDIP, 25/Tube
a) MIC5891YWM:
8-Bit Serial-Input Latched
Source Driver, –40°C to +85°C
Junction Temperature Range,
16-Lead SOICW, 47/Tube
a) MIC5891YWM-TR:
8-Bit Serial-Input Latched
Source Driver, –40°C to +85°C
Junction Temperature Range,
16-Lead SOICW, 1,000/Reel
Device
Junction Package Media Type
Temperature Range
Device:
MIC5891:
Junction
Temperature
Range:
Y
Package:
N
=
WM =
Media Type:
TR
= 1,000/Reel for WM Package
(blank)= 25/Tube for N Package
(blank)= 47/Tube for WM Package
=
8-Bit Serial-Input Latched Source Driver
–40°C to +85°C
16-Lead PDIP
16-Lead SOICW
2016 - 2022 Microchip Technology Inc.
DS20005638B-page 15
MIC5891
NOTES:
DS20005638B-page 16
2016 - 2022 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip products:
•
Microchip products meet the specifications contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and
under normal conditions.
•
Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of
Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not
mean that we are guaranteeing the product is “unbreakable”. Code protection is constantly evolving. Microchip is committed to
continuously improving the code protection features of our products.
This publication and the information herein may be used only
with Microchip products, including to design, test, and integrate
Microchip products with your application. Use of this information in any other manner violates these terms. Information
regarding device applications is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your
specifications. Contact your local Microchip sales office for
additional support or, obtain additional support at https://
www.microchip.com/en-us/support/design-help/client-supportservices.
THIS INFORMATION IS PROVIDED BY MICROCHIP "AS IS".
MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED,
WRITTEN OR ORAL, STATUTORY OR OTHERWISE,
RELATED TO THE INFORMATION INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A
PARTICULAR PURPOSE, OR WARRANTIES RELATED TO
ITS CONDITION, QUALITY, OR PERFORMANCE.
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY
KIND WHATSOEVER RELATED TO THE INFORMATION OR
ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS
BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES
ARE FORESEEABLE. TO THE FULLEST EXTENT
ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON
ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION
OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF
ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP
FOR THE INFORMATION.
Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to
defend, indemnify and hold harmless Microchip from any and
all damages, claims, suits, or expenses resulting from such
use. No licenses are conveyed, implicitly or otherwise, under
any Microchip intellectual property rights unless otherwise
stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec,
AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud,
CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO,
JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus,
maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo,
MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower,
PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch,
SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash,
Symmetricom, SyncServer, Tachyon, TimeSource, tinyAVR, UNI/O,
Vectron, and XMEGA are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
AgileSwitch, APT, ClockWorks, The Embedded Control Solutions
Company, EtherSynch, Flashtec, Hyper Speed Control, HyperLight
Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3,
Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, QuietWire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub,
TimePictra, TimeProvider, TrueTime, WinPath, and ZL are
registered trademarks of Microchip Technology Incorporated in the
U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky,
BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive,
CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net,
Dynamic Average Matching, DAM, ECAN, Espresso T1S,
EtherGREEN, GridTime, IdealBridge, In-Circuit Serial
Programming, ICSP, INICnet, Intelligent Paralleling, Inter-Chip
Connectivity, JitterBlocker, Knob-on-Display, maxCrypto, maxView,
memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo,
MPLIB, MPLINK, MultiTRAK, NetDetach, NVM Express, NVMe,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple
Blocker, RTAX, RTG4, SAM-ICE, Serial Quad I/O, simpleMAP,
SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI,
SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total
Endurance, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY,
ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks
of Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage
Technology, Symmcom, and Trusted Time are registered
trademarks of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany
II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in
other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2016 - 2022, Microchip Technology Incorporated and its subsidiaries.
All Rights Reserved.
For information regarding Microchip’s Quality Management Systems,
please visit www.microchip.com/quality.
2016 - 2022 Microchip Technology Inc. and its subsidiaries.
ISBN: 978-1-5224-9832-2
DS20005638B-page 17
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
DS20005638B-page 18
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Denmark - Copenhagen
Tel: 45-4485-5910
Fax: 45-4485-2829
Finland - Espoo
Tel: 358-9-4520-820
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-72400
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7288-4388
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
2016 - 2022 Microchip Technology Inc. and its subsidiaries.
09/14/21