MIC7111YM5-TR

MIC7111 1.8V to 11V, 15 μA, 25 kHz GBW, Rail-to-Rail Input and Output Operational Amplifier Features General Description • • • • • • • • • The MIC7111 is a low-power operational amplifier with rail-to-rail inputs and outputs. The device operates from a 1.8V to 11V single supply or an ±0.9V to ±5.5V dual supply. The device consumes a low 15 μA of current from a 1.8V supply and 25 μA from a 10V supply. The device features a unity gain bandwidth of 25 kHz and swings within 1 mV of either the supply rail with a 100 kΩ load. The device is capable of sinking and sourcing 25 mA of current from a 1.8V supply and up to 200 mA from a 10V supply. The device is available in the cost effective SOT23-5 package. 1.8V to 11V Single Supply Operation ±0.9V to ±5.5V Dual Supply Operation Low 15 μA Supply Current at 1.8V 25 kHz Gain Bandwidth 1 mV Input Offset Voltage (Typical) 1 pA Input Bias Current (Typical) 0.01 pA Input Offset Current (Typical) Input-Referred Noise is 110 nV/√Hz at 1 kHz Output Swing to within 1 mV of Rails with 1.8V Supply And 100 kΩ Load • Suitable for Driving Capacitive Loads • Cost Effective SOT23-5 Package Applications • • • • • Wireless and Cellular Communications Gaas RF Bias Amplifier Current Sensing for Battery Chargers Transducer Linearization and Interface Portable Computing Package Type MIC7111 SOT23-5 (M5) (Top View) IN+ V+ OUT 2 1 3 PART IDENTIFICATION MIC7111 Functional Configuration IN+ V+ OUT 3 2 1 A13 4 IN– 5 V–  2020 Microchip Technology Inc. 4 IN– 5 V– DS20006316A-page 1 MIC7111 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † Supply Voltage, (VV+ –VV–) ...................................................................................................................................... +12V Differential Input Voltage, (VIN+ –VIN–) .......................................................................................................... ±(VV+ –VV–) I/O Pin Voltage, (VIN, VOUT), (Note 1) .......................................................................................... VV+ +0.3V to VV––0.3V ESD Protection On All Pins, (Note 2) .......................................................................................................................±2 kV Operating Ratings †† Supply Voltage, (VV+ –VV–) ........................................................................................................................ +1.8V to +11V Maximum Power Dissipation .................................................................................................................................. Note 3 † Notice: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside its recommended operating ratings. †† Notice: The device is not guaranteed to function outside its operating ratings. Note 1: I/O pin voltage is any external voltage to which an input or output is referenced. 2: Devices are ESD protected, however, handling precautions are recommended. All limits guaranteed by testing on statistical analysis. Human body model, 1.5 kΩ in series with 100 pF. 3: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX); the junction-to-ambient thermal resistance, θJA; and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using PD = (TJ(MAX) – TA) ÷ θJA. Exceeding the maximum allowable power dissipation will result in excessive die temperature. See Temperature Specifications section. DC ELECTRICAL CHARACTERISTICS (1.8V) Electrical Characteristics: Unless otherwise indicated, VV+ = +1.8V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Sym. Input Offset Voltage VOS Input Offset Voltage Temperature Drift TCVOS Input Bias Current IB Min. Typ. Max. Units — 0.9 7 mV — — — 9 mV –40°C ≤ TJ ≤ +85°C — 2.0 — μV/C — 1 10 — — 500 0.01 0.5 pA Conditions — — –40°C ≤ TJ ≤ +85°C — Input Offset Current IOS Input Resistance RIN — >10 — TΩ — Positive Power Supply Rejection Ratio +PSRR 60 85 — dB 1.8V ≤ VV+ ≤ 5V, VV– = 0V, VCM = VOUT = 0.9V Negative Power Supply Rejection Ratio –PSRR 60 85 — dB –1.8V ≤ VV– ≤ –5V, VV+ = 0V, VCM = VOUT = –0.9V Common-Mode Rejection Ratio CMRR 50 70 — dB VCM = –0.2V to +2.0V CIN — 3 — pF — Common-Mode Input Capacitance DS20006316A-page 2 — 75 pA –40°C ≤ TJ ≤ +85°C  2020 Microchip Technology Inc. MIC7111 DC ELECTRICAL CHARACTERISTICS (1.8V) (CONTINUED) Electrical Characteristics: Unless otherwise indicated, VV+ = +1.8V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Output Voltage Swing Output Short-Circuit Current (Note 1) Voltage Gain Supply Current Note 1: Sym. Min. Typ. Max. — 0.14 1 Output HIGH, RL = 100 kΩ, Specified as VV+ – VOUT — — 1 Output HIGH, RL = 100 kΩ, Specified as VV+ – VOUT –40°C ≤ TJ ≤ +85°C — 0.14 1 Output LOW, RL = 100 kΩ — — 1 Output LOW, RL = 100 kΩ –40°C ≤ TJ ≤ +85°C — 6.8 23 Output HIGH, RL = 2 kΩ, Specified as VV+ – VOUT — — 34 Output HIGH, RL = 2 kΩ, Specified as VV+ – VOUT –40°C ≤ TJ ≤ +85°C — 6.8 23 Output LOW, RL = 2 kΩ — — 34 Output LOW, RL = 2 kΩ –40°C ≤ TJ ≤ +85°C 15 25 — 15 25 — — 400 — — 400 — — 15 35 VOUT ISC AVOL IS Units mV mA V/mV μA Conditions Sourcing, VOUT = 0V Sinking, VOUT = 1.8V Sourcing Sinking VV+ = 1.8V, VOUT = VV+/2 Short circuit may cause device to exceed maximum allowable power dissipation. AC ELECTRICAL CHARACTERISTICS (1.8V) Electrical Characteristics: Unless otherwise indicated, VV+ = +1.8V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Slew Rate Gain Bandwidth Product Sym. Min. Typ. Max. Units Conditions SR — 0.015 — V/μs Voltage follower, 1V step, RL = 100 kΩ at 0.9V, VOUT = 1VPP GBWP — 25 — kHz — DC ELECTRICAL CHARACTERISTICS (2.7V) Electrical Characteristics: Unless otherwise indicated, VV+ = +2.7V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Sym. Input Offset Voltage VOS Input Offset Voltage Temperature Drift TCVOS Note 1: Min. Typ. Max. Units Conditions — 0.9 7 mV — — — 9 mV –40°C ≤ TJ ≤ +85°C — 2.0 — μV/C — Short circuit may cause device to exceed maximum allowable power dissipation.  2020 Microchip Technology Inc. DS20006316A-page 3 MIC7111 DC ELECTRICAL CHARACTERISTICS (2.7V) (CONTINUED) Electrical Characteristics: Unless otherwise indicated, VV+ = +2.7V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Input Bias Current Sym. IB Min. Typ. Max. — 1 10 — — 500 0.01 0.5 Units pA Conditions — –40°C ≤ TJ ≤ +85°C — Input Offset Current IOS Input Resistance RIN — >10 — TΩ — Positive Power Supply Rejection Ratio +PSRR 60 90 — dB 2.7V ≤ VV+ ≤ 5V, VV– = 0V, VCM = VOUT = 1.35V Negative Power Supply Rejection Ratio –PSRR 60 90 — dB –2.7V ≤ VV– ≤ –5V, VV+ = 0V, VCM = VOUT = –1.35V Common-Mode Rejection Ratio CMRR 52 75 — dB VCM = –0.2V to +2.9V CIN — 3 — pF — — 0.2 1 Output HIGH, RL = 100 kΩ, Specified as VV+ – VOUT — — 1 Output HIGH, RL = 100 kΩ, Specified as VV+ – VOUT –40°C ≤ TJ ≤ +85°C — 0.2 1 Output LOW, RL = 100 kΩ — — 1 Output LOW, RL = 100 kΩ –40°C ≤ TJ ≤ +85°C — 10 33 Output HIGH, RL = 2 kΩ, Specified as VV+ – VOUT — — 50 Output HIGH, RL = 2 kΩ, Specified as VV+ – VOUT –40°C ≤ TJ ≤ +85°C — 10 33 Output Low, RL = 2 kΩ — — 50 Output Low, RL = 2 kΩ –40°C ≤ TJ ≤ +85°C 30 50 — 30 50 — — 400 — — 400 — — 17 42 Common-Mode Input Capacitance Output Voltage Swing Output Short-Circuit Current (Note 1) Voltage Gain Supply Current Note 1: — 75 VOUT ISC AVOL IS pA mV mA V/mV μA –40°C ≤ TJ ≤ +85°C Sourcing, VOUT = 0V Sinking, VOUT = 2.7V Sourcing Sinking VV+ = 2.7V, VOUT = VV+/2 Short circuit may cause device to exceed maximum allowable power dissipation. DS20006316A-page 4  2020 Microchip Technology Inc. MIC7111 AC ELECTRICAL CHARACTERISTICS (2.7V) Electrical Characteristics: Unless otherwise indicated, VV+ = +2.7V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Slew Rate Gain Bandwidth Product Sym. Min. Typ. Max. Units Conditions SR — 0.015 — V/μs Voltage follower, 1V step, RL = 100 kΩ @ 1.35V, VOUT = 1VPP GBWP — 25 — kHz — DC ELECTRICAL CHARACTERISTICS (5.0V) Electrical Characteristics: Unless otherwise indicated, VV+ = +5.0V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Sym. Input Offset Voltage VOS Input Offset Voltage Temperature Drift TCVOS Input Bias Current IB Min. Typ. Max. Units — 0.9 7 mV — — — 9 mV –40°C ≤ TJ ≤ +85°C — 2.0 — μV/C — 1 10 — — 500 0.01 0.5 pA Conditions — — –40°C ≤ TJ ≤ +85°C — Input Offset Current IOS Input Resistance RIN — >10 — TΩ — Positive Power Supply Rejection Ratio +PSRR 65 95 — dB 5V ≤ VV+ ≤ 10V, VV– = 0V, VCM = VOUT = 2.5V Negative Power Supply Rejection Ratio –PSRR 65 95 — dB –5V ≤ VV– ≤ –10V, VV+ = 0V, VCM = VOUT = –2.5V Common-Mode Rejection Ratio CMRR 57 80 — dB VCM = –0.2V to +5.2V CIN — 3 — pF — — 0.3 1.5 Output HIGH, RL = 100 kΩ, Specified as VV+ – VOUT — — 1.5 Output HIGH, RL = 100 kΩ, Specified as VV+ – VOUT –40°C ≤ TJ ≤ +85°C — 0.3 1.5 Output LOW, RL = 100 kΩ — — 1.5 Output LOW, RL = 100 kΩ –40°C ≤ TJ ≤ +85°C Common-Mode Input Capacitance Output Voltage Swing  2020 Microchip Technology Inc. — 75 VOUT pA mV –40°C ≤ TJ ≤ +85°C — 15 50 Output HIGH, RL = 2 kΩ, Specified as VV+ – VOUT — — 75 Output HIGH, RL = 2 kΩ, Specified as VV+ – VOUT –40°C ≤ TJ ≤ +85°C — 15 50 Output LOW, RL = 2 kΩ — — 75 Output LOW, RL = 2 kΩ –40°C ≤ TJ ≤ +85°C DS20006316A-page 5 MIC7111 DC ELECTRICAL CHARACTERISTICS (5.0V) (CONTINUED) Electrical Characteristics: Unless otherwise indicated, VV+ = +5.0V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Output Short-Circuit Current (Note 1) Voltage Gain Supply Current Note 1: Sym. ISC AVOL IS Min. Typ. Max. 80 100 — 80 100 — — 500 — — 500 — — 20 50 Units mA V/mV μA Conditions Sourcing, VOUT = 0V Sinking, VOUT = 5V Sourcing Sinking VV+ = 5V, VOUT = VV+/2 Short circuit may cause device to exceed maximum allowable power dissipation. AC ELECTRICAL CHARACTERISTICS (5.0V) Electrical Characteristics: Unless otherwise indicated, VV+ = +5.0V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Slew Rate Gain Bandwidth Product Sym. Min. Typ. Max. Units Conditions SR — 0.02 — V/μs Voltage follower, 1V step, RL = 100 kΩ @ 1.5V, VOUT = 1VPP GBWP — 25 — kHz Sourcing DC ELECTRICAL CHARACTERISTICS (10.0V) Electrical Characteristics: Unless otherwise indicated, VV+ = +10.0V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Sym. Input Offset Voltage VOS Input Offset Voltage Temperature Drift TCVOS Input Bias Current IB Min. Typ. Max. Units — 0.9 7 mV — — — 9 mV –40°C ≤ TJ ≤ +85°C — 2.0 — μV/C — 1 10 — — 500 0.01 0.5 pA Conditions — — –40°C ≤ TJ ≤ +85°C — Input Offset Current IOS Input Resistance RIN — >10 — TΩ — Positive Power Supply Rejection Ratio +PSRR 65 95 — dB 5V ≤ VV+ ≤ 10V, VV– = 0V, VCM = VOUT = 2.5V Negative Power Supply Rejection Ratio –PSRR 65 95 — dB –5V ≤ VV– ≤ –10V, VV+ = 0V, VCM = VOUT = –2.5V Common-Mode Rejection Ratio CMRR 60 85 — dB VCM = –0.2V to +10.2V CIN — 3 — pF — Common-Mode Input Capacitance DS20006316A-page 6 — 75 pA –40°C ≤ TJ ≤ +85°C  2020 Microchip Technology Inc. MIC7111 DC ELECTRICAL CHARACTERISTICS (10.0V) (CONTINUED) Electrical Characteristics: Unless otherwise indicated, VV+ = +10.0V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Output Voltage Swing Output Short-Circuit Current (Note 1) Voltage Gain Supply Current Note 1: Sym. Min. Typ. Max. — 0.45 2.5 Output HIGH, RL = 100 kΩ, Specified as VV+ – VOUT — — 2.5 Output HIGH, RL = 100 kΩ, Specified as VV+ – VOUT –40°C ≤ TJ ≤ +85°C — 0.45 2.5 Output LOW, RL = 100 kΩ — — 2.5 Output LOW, RL = 100 kΩ –40°C ≤ TJ ≤ +85°C — 24 80 Output HIGH, RL = 2 kΩ, Specified as VV+ –VOUT — — 120 Output HIGH, RL = 2 kΩ, Specified as VV+ –VOUT –40°C ≤ TJ ≤ +85°C — 24 80 Output LOW, RL = 2 kΩ — — 120 Output LOW, RL = 2 kΩ –40°C ≤ TJ ≤ +85°C 100 200 — 100 200 — — 500 — — 500 — — 25 65 VOUT ISC AVOL IS Units mV mA V/mV μA Conditions Sourcing, VOUT = 0V Sinking, VOUT = 10V Sourcing Sinking VV+ = 10V, VOUT = VV+/2 Short circuit may cause device to exceed maximum allowable power dissipation. AC ELECTRICAL CHARACTERISTICS (10.0V) Electrical Characteristics: Unless otherwise indicated, VV+ = +10.0V; VV– = 0V; VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C. Parameters Slew Rate Gain Bandwidth Product Sym. Min. Typ. Max. Units Conditions SR — 0.02 — V/μs Voltage follower, 1V step, RL = 100 kΩ @ 1.35V, VOUT = 1VPP GBWP — 25 — kHz — Phase Margin ϕM — 50 — ° — — Gain Margin GM — 15 — dB Input-Referred Voltage Noise eN — 110 — nV/√Hz f = 1 kHz, VCM = 1.0V Input-Referred Current Noise iN — 0.03 — pA/√Hz f = 1 kHz  2020 Microchip Technology Inc. DS20006316A-page 7 MIC7111 TEMPERATURE SPECIFICATIONS Parameters Sym. Min. Typ. Max. Units Conditions Junction Operating Temperature TJ –40 — +85 °C Storage Temperature Range TA –65 — +150 °C — Lead Temperature TS — +260 — °C Soldering, 10s JA — 252 — °C/W Temperature Ranges — Package Thermal Resistances Thermal Resistance, SOT-23-5Ld DS20006316A-page 8 —  2020 Microchip Technology Inc. MIC7111 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: PIN FUNCTION TABLE Pin Number Pin Name 1 OUT Amplifier Output. 2 V+ Positive Supply. 3 IN+ Non-inverting Input. 4 IN– Inverting Input. 5 V– Negative Supply.  2020 Microchip Technology Inc. Description DS20006316A-page 9 MIC7111 3.0 APPLICATION INFORMATION 3.1 Input Common Mode Voltage The MIC7111 tolerates input overdrive by at least 300 mV beyond either rail without producing phase inversion. If the absolute maximum input voltage is exceeded, the input current should be limited to ±5 mA maximum to prevent reducing reliability. A 10 kΩ series input resistor, used as a current limiter, will protect the input structure from voltages as large as 50V above the supply or below ground. See Figure 3-1. VIN RIN 10kŸ FIGURE 3-1: Protection. 3.2 VOUT Input Current-Limit Output Voltage Swing Sink and source output resistances of the MIC7111 are equal. Maximum output voltage swing is determined by the load and the approximate output resistance. The output resistance is presented in Equation 3-1: 3.3 Driving Capacitative Loads Driving a capacitive load introduces phase-lag into the output signal, and this, in turn, reduces op-amp system phase margin. The application that is least forgiving of reduced phase margin is a unity gain amplifier. The MIC7111 can typically drive a 500 pF capacitive load connected directly to the output when configured as a unity-gain amplifier. 3.4 Using Large-Value Feedback Resistors A large-value feedback resistor (>500 kΩ) can reduce the phase margin of a system. This occurs when the feedback resistor acts in conjunction with input capacitance to create phase lag in the feedback signal. Input capacitance is usually a combination of input circuit components and other parasitic capacitance, such as amplifier input capacitance and stray printed circuit board capacitance. Figure 3-2 illustrates a method of compensating phase lag caused by using a large-value feedback resistor. Feedback capacitor CFB introduces sufficient phase lead to overcome the phase lag caused by feedback resistor RFB and input capacitance CIN. The value of CFB is determined by first estimating CIN and then applying the following formula: EQUATION 3-4: R IN  C IN  R FB  C FB EQUATION 3-1: V DROP R OUT = ----------------I LOAD VDROP is the voltage dropped within the amplifier output stage. VDROP and ILOAD can be determined from the VO (output swing) portion of the appropriate electrical characteristics table. ILOAD is equal to the typical output high voltage minus V+/2 and divided by RLOAD. For example, using the DC Electrical Characteristics (5.0V) table, the typical output voltage drop using a 2 kΩ load (connected to V+/2) is 0.015V, which produces an ILOAD of: EQUATION 3-2: 2.5V – 0.015V ------------------------------------ = 1.243mA 2k CFB VIN RIN RFB VOUT CIN FIGURE 3-2: Lag. Canceling Feedback Phase Because a significant percentage of CIN may be caused by board layout, it is important to note that the correct value of CFB may change when changing from a breadboard to the final circuit layout. Then: 3.5 EQUATION 3-3: Some single-supply, rail-to-rail applications for which the MIC7111 is well suited are shown in the circuit diagrams of Figure 3-3 through Figure 3-8. 15mV R OUT = ---------------------- = 12.1 = 12 1.243mA DS20006316A-page 10 Typical Circuits  2020 Microchip Technology Inc. MIC7111 V+ 1.8V TO 10V VIN 2 1 V+ 0V TO AV 4 R1 10Nȍ MIC7111 MIC7111 VOUT 0V TO V+ 5 Noninverting Amplifier. Q1 2N3904 5 { VCEO = 40V IC(MAX) = 200mA RS 10Ÿ ½W VIN = 100mA/V AS SHOWN RS IOUT = Voltage-Controlled Current VOUT (V) R4 Nȍ R2 § AV = 1 + R1 0 C1 0.001μF V+ 4 3 Noninverting Amplifier 2 VOUT 0V TO V+ 5 FIGURE 3-7: 5 Square Wave Oscillator. R2 Nȍ CIN MIC7111 R1 Nȍ VOUT = VIN Voltage Follower/Buffer. V+ 4 2 1 3 V+ 5 COUT RL VOUT 0V R3 Nȍ C1 1μF FIGURE 3-8: Amplifier.  2020 Microchip Technology Inc. VOUT V+ 0V R4 Nȍ R3 Nȍ MIC7111 1 4 2 R2 Nȍ V+ 3 MIC7111 1 VIN (V) V+ 1.8V TO 10V FIGURE 3-5: VOUT 0V TO V+ IOUT 1 FIGURE 3-6: Sink. FIGURE 3-4: Behavior. VIN 0V TO V+ 2 CHANGE Q1 AND RS FOR HIGHER CURRENT AND/OR DIFFERENT GAIN V+ 0 3 VIN 0V TO 2V 4 R2 91Nȍ FIGURE 3-3: V+ 1.8V TO 10V LOAD 3 VS 0.5V TO Q1 VCEO(SUS) R2 Nȍ –10 R4 AV = – = = R1 Nȍ Nȍ AC-Coupled Inverting DS20006316A-page 11 MIC7111 4.0 PACKAGING INFORMATION 4.1 Package Marking Information 5-Lead SOT-23* (Front) XXX e3 * A13 5-Lead SOT-23* Example NNN 469 (Back) Legend: XX...X Y YY WW NNN Example Product code or customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC® designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. ●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle mark). Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. Package may or may not include the corporate logo. Underbar (_) and/or Overbar (‾) symbol may not be to scale. DS20006316A-page 12  2020 Microchip Technology Inc. MIC7111 5-Lead SOT23-5 Package Outline & Recommended Land Pattern Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging.  2020 Microchip Technology Inc. DS20006316A-page 13 MIC7111 NOTES: DS20006316A-page 14  2020 Microchip Technology Inc. MIC7111 APPENDIX A: REVISION HISTORY Revision A (March 2020) • Converted Micrel document MIC7111 to Microchip data sheet template DS20006316A. • Minor grammatical text changes throughout.  2020 Microchip Technology Inc. DS20006316A-page 15 MIC7111 NOTES: DS20006316A-page 16  2020 Microchip Technology Inc. MIC7111 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office. PART NO. X XX -XX Device Temperature Range Package Media Type Device: MIC7111: 1.8V to 11V, 15 μA, 25 kHz GBW, Rail-to-Rail Input and Output Operational Amplifier Temperature Range: Y = –40C to +85C (Industrial) Packages: M5 = 5-Lead SOT-23 Media Type: TR = 3,000/Reel  2020 Microchip Technology Inc. Examples: a) MIC7111YM5-TR: Note 1: MIC7111, –40°C to +85°C Temperature Range, 5Lead SOT-23, 3,000/Reel Tape and Reel identifier only appears in the catalog part number description. This identifier is used for ordering purposes and is not printed on the device package. Check with your Microchip Sales Office for package availability with the Tape and Reel option. DS20006316A-page 17 MIC7111 NOTES: DS20006316A-page 18  2020 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip name and logo, the Microchip logo, Adaptec, AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, chipKIT, chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer, PackeTime, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon, TempTrackr, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, FlashTec, Hyper Speed Control, HyperLight Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3, Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet-Wire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub, TimePictra, TimeProvider, Vite, WinPath, and ZL are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BlueSky, BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, INICnet, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. The Adaptec logo, Frequency on Demand, Silicon Storage Technology, and Symmcom are registered trademarks of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2020, Microchip Technology Incorporated, All Rights Reserved. For information regarding Microchip’s Quality Management Systems, please visit www.microchip.com/quality.  2020 Microchip Technology Inc. ISBN: 978-1-5224-5737-4 DS20006316A-page 19 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Australia - Sydney Tel: 61-2-9868-6733 India - Bangalore Tel: 91-80-3090-4444 China - Beijing Tel: 86-10-8569-7000 India - New Delhi Tel: 91-11-4160-8631 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 China - Chengdu Tel: 86-28-8665-5511 India - Pune Tel: 91-20-4121-0141 Denmark - Copenhagen Tel: 45-4485-5910 Fax: 45-4485-2829 China - Chongqing Tel: 86-23-8980-9588 Japan - Osaka Tel: 81-6-6152-7160 Finland - Espoo Tel: 358-9-4520-820 China - Dongguan Tel: 86-769-8702-9880 Japan - Tokyo Tel: 81-3-6880- 3770 China - Guangzhou Tel: 86-20-8755-8029 Korea - Daegu Tel: 82-53-744-4301 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 China - Hangzhou Tel: 86-571-8792-8115 Korea - Seoul Tel: 82-2-554-7200 China - Hong Kong SAR Tel: 852-2943-5100 Malaysia - Kuala Lumpur Tel: 60-3-7651-7906 China - Nanjing Tel: 86-25-8473-2460 Malaysia - Penang Tel: 60-4-227-8870 China - Qingdao Tel: 86-532-8502-7355 Philippines - Manila Tel: 63-2-634-9065 China - Shanghai Tel: 86-21-3326-8000 Singapore Tel: 65-6334-8870 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 China - Shenyang Tel: 86-24-2334-2829 Taiwan - Hsin Chu Tel: 886-3-577-8366 Germany - Rosenheim Tel: 49-8031-354-560 China - Shenzhen Tel: 86-755-8864-2200 Taiwan - Kaohsiung Tel: 886-7-213-7830 Israel - Ra’anana Tel: 972-9-744-7705 China - Suzhou Tel: 86-186-6233-1526 Taiwan - Taipei Tel: 886-2-2508-8600 China - Wuhan Tel: 86-27-5980-5300 Thailand - Bangkok Tel: 66-2-694-1351 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 China - Xian Tel: 86-29-8833-7252 Vietnam - Ho Chi Minh Tel: 84-28-5448-2100 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 DS20006316A-page 20 China - Xiamen Tel: 86-592-2388138 China - Zhuhai Tel: 86-756-3210040 Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-72400 Germany - Karlsruhe Tel: 49-721-625370 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-7288-4388 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820  2020 Microchip Technology Inc. 02/28/20