PIC16LF1768-I/P

PIC16(L)F1764/5/8/9 14/20-Pin, 8-Bit Flash Microcontroller Product Brief Description: PIC16(L)F176X microcontrollers combine intelligent analog integration with digital peripherals to suit a variety of functions and end equipment. These 14/20-pin devices provide features like 10-bit A/D, op amps, zero-cross detect, high current IOs, communication, peripheral pin select and other key peripherals that make this family appealing in applications looking for design flexibility. Core Features: Digital Peripherals: • C Compiler Optimized RISC Architecture • Only 49 Instructions • Operating Speed: - DC – 32 MHz clock input - 125 ns minimum instruction cycle • Interrupt Capability • 16-Level Deep Hardware Stack • Up to Four 8-Bit Timers • Up to Three 16-Bit Timers • Power-on Reset (POR) • Configurable Power-up Timer (PWRT) • Brown-out Reset (BOR) with Selectable Trip Point • Extended Watchdog Timer (EWDT): - Low-power 31 kHz WDT - Software-selectable prescaler - Software-selectable enable • Configurable Logic Cell (CLC): - Up to three CLCs; up to four selected inputs - Integrated combinational and state logic • Up to Two Complementary Output Generators (COG): - Push-Pull, Full-Bridge and Steering modes • Up to Two Capture/Compare/PWM (CCP) modules • Pulse-Width Modulators (PWM): - Up to two 10-bit PWMs - Up to two 16-bit PWMs • Peripheral Pin Select (PPS): - Configure any digital pin to output • Serial Communications: - Enhanced USART (EUSART) - SPI, I2C™, RS-232, RS-485, LIN compatible - Auto-Baud Detect, auto-wake-up on start • Up to 18 I/O Pins: - Individually programmable pull-ups - Slew rate control - Interrupt-on-change with edge-select • Up to Two Data Signal Modulators (DSM) Memory: • • • • Up to 14 KB Flash Program Memory Up to 1024 Bytes Data RAM Memory Direct, Indirect and Relative Addressing modes High Endurance Flash (HEF) - 128B of nonvolatile data storage - 100K Erase/Write cycles Operating Characteristics: • Operating Voltage Range: - 1.8V to 3.6V (PIC16LF176X) - 2.3V to 5.5V (PIC16F176X) • Temperature Range: - Industrial: -40°C to 85°C - Extended: -40°C to 125°C eXtreme Low-Power (XLP) Features: • • • • Sleep mode: 50 nA @ 1.8V, typical Watchdog Timer: 500 nA @ 1.8V, typical Secondary Oscillator 500 nA @ 32 kHz Operating Current: - 8 uA @ 32 kHz, 1.8V, typical - 32 uA/MHz @ 1.8V, typical • Low-Power BOR (LPBOR): - 200 nA in Sleep  2014 Microchip Technology Inc. Intelligent Analog Peripherals: • 10-Bit Analog-to-Digital Converter (ADC): - Up to 12 external channels - Conversion available during Sleep • Up to Two Operational Amplifiers (OPA): - Selectable internal and external channels - High and low GBWP operating modes • Up to Four Fast Comparators (COMP): - Low-Power/High-Speed mode - Up to five external inverting inputs - Up to eight external non-inverting inputs - Fixed Voltage Reference at non-inverting input(s) - Comparator outputs externally accessible • Digital-to-Analog Converters (DAC): - Up to two 10-bit resolution DACs - Up to two 5-bit resolution DACs Advance Information DS40001751A-page 1 PIC16(L)F1764/5/8/9 Clocking Structure: • Voltage Reference: - Fixed Voltage Reference (FVR): 1.024V, 2.048V and 4.096V output levels • Zero-Cross Detector (ZCD): - Detect high voltage AC signal • Programmable Ramp Generator (PRG) - Slope compensation - Ramp generation • High Current Drive I/Os: - 100 mA capacity - Low voltage Device Program Memory Flash (words) High-Endurance Flash (B) Data SRAM (bytes) I/O Pins 8/16-bit Timer Comparator 10-bit ADC (ch) 5/10-bit DAC CCP 10/16-bit PWM COG DSM CLC Op Amp Zero-Cross Detect Programmable Ramp Gen High Current I/Os Peripheral Pin Select EUSART I2C™/SPI Debug(1) PIC16(L)F1764/5/8/9 FAMILY TYPES Data Sheet Index TABLE 1: • 16 MHz Internal Oscillator: - ±1% at calibration - Selectable frequency range 32 MHz to 31 kHz • 31 kHz Low-Power Internal Oscillator • 4x Phase-Locked Loop (PLL): - For up to 32 MHz internal operation • External Oscillator Block with: - Three external clock modes up to 32 MHz PIC16(L)F1764 (A) 4096 128 512 12 4/3 2 8 1/1 1 1/1 1 1 3 1 1 1 2 Y 1 1 I/H PIC16(L)F1765 (A) 8192 128 1024 12 4/3 2 8 1/1 1 1/1 1 1 3 1 1 1 2 Y 1 1 I/H PIC16(L)F1768 (B) 4096 128 512 18 4/3 4 12 2/2 2 2/2 2 2 3 2 1 2 2 Y 1 1 I/H PIC16(L)F1769 (B) 8192 128 1024 18 4/3 4 12 2/2 2 2/2 2 2 3 2 1 2 2 Y 1 1 I/H Note 1: Debugging Methods: (I) – Integrated on Chip; (H) – via ICD header; E – Emulation Product. Data Sheet Index: A. Future Release PIC16(L)F1764/5 Data Sheet, 14-Pin, 8-bit Flash Microcontrollers. B. Future Release PIC16(L)F1768/9 Data Sheet, 20-Pin, 8-bit Flash Microcontrollers. Note: For other small form-factor package availability and marking information, please visit http://www.microchip.com/packaging or contact your local sales office. TABLE 2: PACKAGES PDIP SOIC TSSOP QFN PIC16(L)F1764 Packages X X X X PIC16(L)F1765 X X X X PIC16(L)F1768 X X X X PIC16(L)F1769 X X X X Note: SSOP Pin details are subject to change. DS40001751A-page 2 Advance Information  2014 Microchip Technology Inc. PIC16(L)F1764/5/8/9 PIN DIAGRAMS 14-PIN PDIP, SOIC, TSSOP 1 RA5 2 RA4 3 MCLR/VPP/RA3 4 RC5 5 RC4 6 PIC16(L)F1765 VDD PIC16(L)F1764 FIGURE 1: VSS 14 13 RA0/ICSPDAT 12 RA1/ICSPCLK 11 RA2 10 RC0 9 RC1 8 RC2 RC3 7 Note: See Table 3 for location of all peripheral functions. VSS NC NC 16-PIN QFN (4x4) VDD FIGURE 2: 16 15 14 13 RA5 1 12 RA0 RA4 2 PIC16(L)F1764 11 RA1 PIC16(L)F1765 MCLR/VPP/RA3 3 10 RA2 9 RC0 5 6 7 8 RC4 RC3 RC2 RC1 RC5 4 Note: See Table 3 for location of all peripheral functions.  2014 Microchip Technology Inc. Advance Information DS40001751A-page 3 PIC16(L)F1764/5/8/9 20-PIN PDIP, SOIC, SSOP 20 VSS 19 RA0 RA4 3 18 RA1 MCLR/VPP/RA3 4 17 RA2 RC5 5 RC4 6 RC3 7 PIC16(L)F1769 VDD 1 RA5 2 PIC16(L)F1768 FIGURE 3: 16 RC0 15 RC1 14 RC2 RC6 8 13 RB4 RC7 9 12 RB5 RB7 10 11 RB6 Note: See Table 4 for location of all peripheral functions. RA0 VSS VDD RA5 20-PIN QFN (4x4) RA4 FIGURE 4: 20 19 18 17 16 15 RA1 MCLR/VPP/RA3 1 RC5 2 RC4 3 PIC16(L)F1768 PIC16(L)F1769 14 RA2 13 RC0 11 RC2 8 9 10 RB4 7 RB5 6 RB6 RC6 5 RB7 12 RC1 RC7 RC3 4 Note: See Table 4 for location of all peripheral functions. DS40001751A-page 4 Advance Information  2014 Microchip Technology Inc. Hi Current C1IN0+ C2IN0+ — — — — — — — — — — IOC Y — ICSPDAT RA1 12 11 AN1 VREF+ DAC1REF+ DAC2REF+ — — C1IN0C2IN0- — — — — — — — — — — IOC Y — ICSPCLK RA2 11 10 AN2 — — — — ZCD — T0CKI(1) — — COG1IN(1) — — — — INT(1) IOC Y — — — — — — DSM1CH(1) — — IOC Y — VPP MCLR ICD MSSP DSM CLC CCP PWM Timers Zero Cross Op Amp DAC Basic Pull-ups — Interrupts DAC1OUT1 DAC2OUT1 EUSART VREFDAC1REFDAC2REF- COG AN0 Ramp Generator 12 Comparator 13 Reference ADC RA0 RA3 4 3 — — — — — — — T6CKI(1) RA4 3 2 AN3 — — — — — — T1G(1) SOSCO — — — — DSM1CL(1) — — IOC Y — OSC2 CLKOUT RA5 2 1 — — — — — — — T1CKI(1) T2CKI(1) SOSCI — — — CLCIN3(1) DSM1MOD(1) — — IOC Y — OSC1 CLKIN RC0 10 9 AN4 — — OPA1IN+ C2IN0+ — — T5CKI(1) — — — — — — SCL(1) SCK(1,3) IOC Y — — RC1 9 8 AN5 — — OPA1IN- C1IN1C2IN1- — — T4CKI(1) — — — CLCIN2(1) — — SDI(1) SDA(1,3) IOC Y — — RC2 8 7 AN6 — — OPA1OUT C1IN2C2IN2- — RG1IN0 — — — — — — — — IOC Y — — RC3 7 6 AN7 — — — C1IN3C2IN3- — — T5G(1) — — — CLCIN0(1) — — SS(1) IOC Y — — RC4 6 5 — — — — — — RG1R(1) T3G(1) — — — CLCIN1(1) — CK(1) — IOC Y Y — T3CKI(1) — CCP1(1) — — — RX(1,3) — IOC Y Y — DS40001751A-page 5 RC5 5 4 — — — — — — RG1F(1) VDD 1 16 — — — — — — — — — — — — — — — — — — VDD VSS 14 13 — — — — — — — — — — — — — — — — — — VSS OUT(2) — — — — — — C1OUT — — — PWM3OUT CCP1 COG1A CLC1OUT DSM1OUT DT(3) SDO INT — — — — — — — — — C2OUT — — — PWM5OUT — COG1B CLC2OUT — TX SDA(3) — — — — — — — — — — — — — — — — COG1C CLC3OUT — CK SCK(3) — — — — — — — — — — — — — — — — COG1D — — — SCL — — — — Note 1: 2: 3: Default peripheral input. Input can be moved to any other pin with the PPS input selection register. All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers. These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections. PIC16(L)F1764/5/8/9 Advance Information 16-Pin QFN 14-PIN AND 16-PIN ALLOCATION TABLE (PIC16(L)F1764 AND PIC16(L)F1765) 14-Pin PDIP/SOIC/TSSOP TABLE 3: I/O  2014 Microchip Technology Inc. PIN ALLOCATION TABLES Pull-ups Hi Current Basic DAC1OUT1 DAC2OUT1 DAC3OUT1 DAC4OUT1 — C1IN0+ C3IN0+ — — — — — — — — — — IOC Y — ICSPDAT RA1 18 15 AN1 VREF+ DAC1REF+ DAC2REF+ DAC3REF+ DAC4REF+ — — C1IN0C2IN0C3IN0C4IN0- — — — — — — — — — — IOC Y — ICSPCLK RA2 17 14 AN2 — — — — ZCD — T0CKI(1) — — COG1IN(1) COG2IN(1) — — — — INT(1) Y IOC — — RA3 4 1 — — — — — — — T6CKI(1) — — — — DSM1CH(1) DSM2CH(1) — — IOC Y — VPP MCLR ICD RA4 3 20 AN3 — — — — — — T1G(1) SOSCO — — — — DSM1CL(1) DSM2CL(1) — — IOC Y — OSC2 CLKOUT RA5 2 19 — — — — — — — T1CKI(1) T2CKI(1) SOSCI — — — CLCIN3(1) DSM1MOD(1) — DSM2MOD(1) — IOC Y — OSC1 CLKIN RB4 13 10 AN10 — — OPA1IN0- — — — — — — — — — — SDI(1) SDA(1,3) IOC Y — — RB5 12 9 AN11 — — OPA1IN0+ — — — — — — — — — RX(1,3) — IOC Y — — RB6 11 8 — — — — C1IN1+ C3IN1+ — — — — — — — — — SCL(1) SCK(1,3) IOC Y — — RB7 10 7 — — — — C2IN1C4IN1+ — — — — — — — — CK(1) — IOC Y — — RC0 16 13 AN4 — — — C2IN0C4IN0+ — — T5CKI(1) — — — — — — — IOC Y — — RC1 15 12 AN5 — — — C1IN1C2IN1C3IN1C4IN1- — — T4CKI(1) — — — CLCIN2(1) — — — IOC Y — — RC2 14 11 AN6 — — OPA1OUT OPA2IN1OPA2IN1+ C1IN2C2IN2- — RG1IN0 RG2IN1 — — — — — — — — IOC Y — — Note 1: 2: 3: MSSP DSM CLC CCP PWM Timers Zero Cross Op Amp DAC Default peripheral input. Input can be moved to any other pin with the PPS input selection register. All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers. These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections. Interrupts VREFDAC1REFDAC2REFDAC3REFDAC4REF- EUSART AN0 COG 16 Ramp Generator 19 Comparator ADC RA0 Reference 20-Pin QFN  2014 Microchip Technology Inc. 20-Pin PDIP/SOIC/SSOP Advance Information I/O 20-PIN ALLOCATION TABLE ( PIC16(L)F1768 AND PIC16(L)F1769) PIC16(L)F1764/5/8/9 DS40001751A-page 6 TABLE 4: Hi Current — RG2IN0 RG1IN1 T5G(1) — CCP2(1) — CLCIN0(1) — — — IOC Y — — RC4 6 3 — — — — — — RG1R(1) RG2R(1) T3G(1) — — — CLCIN1(1) — — — IOC Y Y — RC5 5 2 — — — — — — RG1F(1) RG2F(1) T3CKI(1) — CCP1(1) — — — — — IOC Y Y — RC6 8 5 AN8 — — OPA2IN0- — — — — — — — — — — SS(1) IOC Y — — RC7 9 6 AN9 — — OPA2IN0+ — — — — — — — — — — — IOC Y — — VDD 1 18 — — — — — — — — — — — — — — — — — VSS MSSP DSM CLC CCP PWM Timers Zero Cross Op Amp DAC ADC Basic Pull-ups C1IN3C2IN3C3IN3C4IN3- Interrupts OPA2OUT OPA1IN1OPA1IN1+ EUSART — COG — Ramp Generator AN7 Comparator 4 Reference 20-Pin QFN 7 20 17 — — — — — — — — — — — — — — — — — OUT(2) — — — — — — C1OUT — — — PWM3OUT CCP1 COG1A CLC1OUT DSM1OUT DT(3) SDO — — — — — — — — — — C2OUT — — — PWM4OUT CCP2 COG1B CLC2OUT DSM2OUT TX SDA(3) — — — — — — — — — — C3OUT — — — PWM5OUT — COG1C CLC3OUT — CK SCK(3) — — — — — — — — — — C4OUT — — — PWM6OUT — COG1D — — — SCL — — — — — — — — — — — — — — — — COG2A — — — — — — — — — — — — — — — — — — — — COG2B — — — — — — — — — — — — — — — — — — — — COG2C — — — — — — — — — — — — — — — — — — — — COG2D — — — — — — — — Note 1: 2: 3: Default peripheral input. Input can be moved to any other pin with the PPS input selection register. All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers. These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections. DS40001751A-page 7 PIC16(L)F1764/5/8/9 Advance Information 20-Pin PDIP/SOIC/SSOP 20-PIN ALLOCATION TABLE ( PIC16(L)F1768 AND PIC16(L)F1769) RC3 I/O  2014 Microchip Technology Inc. TABLE 4: Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2014, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-63276-174-3 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == DS40001751A-page 8 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. Advance Information  2014 Microchip Technology Inc. Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2943-5100 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Canada - Toronto Tel: 905-673-0699 Fax: 905-673-6509  2014 Microchip Technology Inc. Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hangzhou Tel: 86-571-8792-8115 Fax: 86-571-8792-8116 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Dusseldorf Tel: 49-2129-3766400 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Pforzheim Tel: 49-7231-424750 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Venice Tel: 39-049-7625286 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Poland - Warsaw Tel: 48-22-3325737 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 Advance Information 03/25/14 DS40001751A-page 9