PIC18F66K80 FAMILY
28/40/44/64-Pin, High-Temperature, Enhanced Flash
Microcontrollers with ECAN™ and nanoWatt XLP Technology
High-Temperature Features:
ECAN Bus Module Features (Continued):
• Ambient Temperature Range of -40°C to +150°C
• Six Programmable Receive/Transmit Buffers
• Three Dedicated Transmit Buffers with Prioritization
• Two Dedicated Receive Buffers
• 16 Full, 29-Bit Acceptance Filters with Dynamic
Association
• Three Full, 29-Bit Acceptance Masks
• Automatic Remote Frame Handling
• Advanced Error Management Features
Power-Managed Modes:
•
•
•
•
•
•
•
•
•
•
Run: CPU on, Peripherals on
Idle: CPU off, Peripherals on
Sleep: CPU off, Peripherals off
Two-Speed Oscillator Start-up
Fail-Safe Clock Monitor (FSCM)
Power-Saving Peripheral Module Disable (PMD)
Ultra Low-Power Wake-up
Fast Wake-up, 1 µs, Typical
Low-Power WDT, 300 nA, Typical
Run mode Currents Down to Very Low 3.8 µA,
Typical
• Idle mode Currents Down to Very Low 880 nA,
Typical
• Sleep mode Currents Down to Very Low 13 nA,
Typical
Special Microcontroller Features:
•
•
•
•
•
•
•
ECAN Bus Module Features:
• Conforms to CAN 2.0B Active Specification
• Three Operating modes:
- Legacy mode (full backward compatibility with
existing PIC18CXX8/FXX8 CAN modules)
- Enhanced mode
- FIFO mode or programmable TX/RX buffers
• Message Bit Rates up to 1 Mbps
• DeviceNet™ Data Byte Filter Support
2012 Microchip Technology Inc.
ECAN™
MSSP
BORMV/LVD
DSM
1,024
1,024
1,024
1,024
1,024
1,024
I/O
Comparators
3,648
3,648
3,648
3,648
3,648
3,648
Pins
EUSART
32 Bytes
64 Bytes
32 Bytes
64 Bytes
32 Bytes
64 Bytes
Data
Data
Memory
EE
(Bytes) (Bytes)
Timers
8-Bit/16-Bit
Program
Memory
CCP/
ECCP
PIC18F25K80
PIC18F26K80
PIC18F45K80
PIC18F46K80
PIC18F65K80
PIC18F66K80
DEVICE COMPARISON
12-Bit A/D
Channels
Device
•
•
•
CTMU
TABLE 1:
•
On-Chip 3.3V Regulator
Operating Speed up to 64 MHz
3.6 Kbytes of General Purpose Registers (SRAM)
Three Internal Oscillators:
- LF-INTOSC (31 kHz)
- MF-INTOSC (500 kHz)
- HF-INTOSC (16 MHz)
Priority Levels for Interrupts
8 x 8 Single-Cycle Hardware Multiplier
Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 4,194s
In-Circuit Serial Programming™ (ICSP™) via Two
Pins
In-Circuit Debug via Two Pins
Programmable BOR
Programmable LVD
28
28
40/44
40/44
64
64
24
24
35
35
54
54
1
1
1
1
1
1
8-ch
8-ch
11-ch
11-ch
11-ch
11-ch
4/1
4/1
4/1
4/1
4/1
4/1
2/3
2/3
2/3
2/3
2/3
2/3
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
DS30509A-page 1
PIC18F66K80 FAMILY
Peripheral Highlights:
• Five CCP/ECCP modules:
- Four Capture/Compare/PWM (CCP) modules
- One Enhanced Capture/Compare/PWM
(ECCP) module
• Five 8/16-Bit Timer/Counter modules:
- Timer0: 8/16-bit timer/counter with 8-bit
programmable prescaler
- Timer1, Timer3: 16-bit timer/counter
- Timer2, Timer4: 8-bit timer/counter
• Two Analog Comparators
• Configurable Reference Clock Output
• Charge Time Measurement Unit (CTMU):
- Capacitance measurement
- Time measurement with 1 ns typical resolution
- Integrated voltage reference
DS30509A-page 2
• Up to Four External Interrupts
• One Master Synchronous Serial Port
(MSSP) module:
- 3/4-wire SPI (supports all four SPI modes)
- I2C™ Master and Slave modes
• Two Enhanced Addressable USART modules:
- LIN/J2602 support
- Auto-Baud Detect (ABD)
• 12-Bit A/D Converter with up to 11 Channels:
- Auto-acquisition and Sleep operation
- Differential Input mode of operation
• Data Signal Modulator module:
- Select modulator and carrier sources from
various module outputs
• Integrated Voltage Reference
2012 Microchip Technology Inc.
PIC18F66K80 FAMILY
Table of Contents
1.0
Device Overview .......................................................................................................................................................................... 5
2.0
Special Features of the CPU........................................................................................................................................................ 7
3.0
Electrical Characteristics .............................................................................................................................................................. 9
Appendix A: Revision History............................................................................................................................................................... 13
The Microchip Web Site ....................................................................................................................................................................... 15
Customer Change Notification Service ................................................................................................................................................ 15
Customer Support ................................................................................................................................................................................ 15
Reader Response ................................................................................................................................................................................ 16
Product Identification System .............................................................................................................................................................. 17
2012 Microchip Technology Inc.
DS30509A-page 3
PIC18F66K80 FAMILY
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We
welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
DS30509A-page 4
2012 Microchip Technology Inc.
PIC18F66K80 FAMILY
1.0
DEVICE OVERVIEW
This document contains device-specific information for
the following devices, operating in an ambient
temperature range between -40°C and +150°C:
• PIC18F25K80
• PIC18F46K80
• PIC18F26K80
• PIC18F65K80
• PIC18F45K80
• PIC18F66K80
The primary differentiating features and specifications
of the high-temperature PIC18F66K80 family devices
are:
• Above +125°C, writes are not allowed for Flash
program memory
• All AC timing specifications are increased by 15%
This derating factor includes parameters, such as
TPWRT
• Maximum HS frequency of operation is 64 MHz
Note: This data sheet documents only the devices’
features and specifications that are in
addition to the features and specifications of
the non-specialty PIC18F66K80 devices.
For information on the features and
specifications shared by this document’s hightemperature devices and the non-specialty
devices, see the “PIC18F66K80 Family Data
Sheet” (DS39977).
Note:
The test duration for AEC-Q100 reliability
testing for devices operating at +150°C is
1,000 hours. Any design operating at
+125°C to +150°C for longer than that
period is not warranted without prior written
approval from Microchip Technology Inc.
This family of devices offers the advantages of all
PIC18 microcontrollers; namely, high computational
performance at an economical price. In addition to these
features, the PIC18F66K80 family introduces design
enhancements that make these microcontrollers a logical
choice for many high-performance, power-sensitive
applications.
2012 Microchip Technology Inc.
DS30509A-page 5
PIC18F66K80 FAMILY
NOTES:
DS30509A-page 6
2012 Microchip Technology Inc.
PIC18F66K80 FAMILY
2.0
SPECIAL FEATURES OF THE
CPU
2.1
The Device ID registers are read-only registers. They
identify the device type and revision for device
programmers and can be read by firmware using table
reads.
Note: For additional details on the Configuration bits,
refer to Section 28.1 “Configuration Bits” in
the “PIC18F66K80 Family Data Sheet”
(DS39977). Device ID information presented in
this section is for the high-temperature
PIC18F66K80 family devices only.
TABLE 2-1:
Device ID Registers
DEVICE IDs
File Name
Bit 7
3FFFFEh DEVID1(1)
DEV2
DEV1
DEV0
REV4
REV3
REV2
3FFFFFh DEVID2(1) DEV10
DEV9
DEV8
DEV7
DEV6
DEV5
Legend:
Note 1:
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 0
Default/
Unprogrammed
Value
REV1
REV0
xxxx xxxx
DEV4
DEV3
xxxx xxxx
Bit 1
x = unknown; u = unchanged,;— = unimplemented.
See Register 2-1 and Register 2-2 for DEVIDx values. DEVIDx registers are read-only and cannot be
programmed by the user.
REGISTER 2-1:
DEVID1: DEVICE ID REGISTER 1
R
R
R
R
R
R
R
R
DEV2(1)
DEV1(1)
DEV0(1)
REV4
REV3
REV2
REV1
REV0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-5
DEV: Device ID bits(1)
111 = PIC18F66K80
100 = PIC18F25K80
011 = PIC18F45K80
010 = PIC18F65K80
001 = PIC18F26K80
000 = PIC18F46K80
bit 4-0
REV: Revision ID bits
These bits are used to indicate the device revision.
Note 1:
x = Bit is unknown
These DEV values may be shared with other devices. The specific device is always identified by
using the entire DEV bit sequence.
2012 Microchip Technology Inc.
DS30509A-page 7
PIC18F66K80 FAMILY
REGISTER 2-2:
DEVID2: DEVICE ID REGISTER 2
R
R
R
R
R
R
R
R
DEV10(1)
DEV9(1)
DEV8(1)
DEV7(1)
DEV6(1)
DEV5(1)
DEV4(1)
DEV3(1)
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
Note 1:
x = Bit is unknown
DEV: Device ID bits(1)
0110 0000 = PIC18F66K80
0110 0001 = PIC18F46K80, PIC18F26K80, PIC18F65K80, PIC18F45K80, PIC18F25K80
These DEV values may be shared with other devices. The specific device is always identified by
using the entire DEV bit sequence.
DS30509A-page 8
2012 Microchip Technology Inc.
PIC18F66K80 FAMILY
3.0
ELECTRICAL CHARACTERISTICS
Note: Other than some basic data, this section documents only the high-temperature PIC18F66K80 family devices’
specifications that differ from those of the non-specialty PIC18F66K80 family devices. For detailed information
on the electrical specifications shared by the high-temperature and non-specialty devices, see the
“PIC18F66K80 Family Data Sheet” (DS39977).
Unless otherwise noted, this section’s parameters assume a minimum voltage of 4.0V.
3.1
Absolute Maximum Ratings(†)
Ambient temperature under bias........................................................................................................................... +150°C
Maximum current out of VSS pin .............................................................................................................................60 mA
Maximum current into VDD pin ................................................................................................................................60 mA
Maximum output current sunk by any I/O pin(1) ........................................................................................................1 mA
Maximum output current sourced by any I/O pin(1) ...................................................................................................1 mA
Maximum current sunk by all ports combined(1) .....................................................................................................10 mA
Maximum current sourced by all ports combined(1) ................................................................................................10 mA
Note 1:
Maximum allowable current is a function of device maximum power dissipation (see Section 31.0 “Electrical
Characteristics” in the “PIC18F66K80 Family Data Sheet”.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above
those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions
for extended periods may affect device reliability.
FIGURE 3-1:
PIC18F66K80 VOLTAGE-FREQUENCY GRAPH (HIGH TEMPERATURE)
6.0V
5.5V
5.0V
4.5V
Voltage
4.0V
4.0V
3.5V
3.0V
2.5V
2.0V
64 MHz
Frequency
High-Temperature Devices
2012 Microchip Technology Inc.
DS30509A-page 9
PIC18F66K80 FAMILY
3.2
DC Characteristics: Supply Voltage (High Temperature)
PIC18F66K80 Family
(High Temperature)
Param
Symbol
No.
D001
3.3
Standard Operating Conditions (unless otherwise stated)
Operating temperature
+125°C TA +150°C for high temperature
Characteristic
Supply Voltage
VDD
Min
Typ
Max
Units
4.0
—
5.5
V
Conditions
For F devices
DC Characteristics: Power Down and Supply Current (High Temperature)
PIC18F66K80 Family
(High Temperature)
Param
No.
Device
PIC18FXXK80
Standard Operating Conditions (unless otherwise stated)
Operating temperature
+125°C TA +150°C for high temperature
Typ
Max
Units
Conditions
Power-Down Current (IPD)(1)
10
28
µA
+150°C
VDD = 5V, Sleep mode
Module Differential Currents
12
29
µA
+150°C
VDD = 5V,
Watchdog Timer Current: ΔIWDT
12
28
µA
+150°C
VDD = 5V, A/D Current: ΔIAD
12
28
µA
+150°C
VDD = 5V,
High/Low-Voltage Detect: ΔIHLVD
Supply Current (IDD)(2,3)
Note 1:
2:
3:
10
32
mA
+150°C
VDD = 5V, FOSC = 64 MHz
(PRI_RUN mode)
—
8
mA
+150°C
VDD = 5V, FOSC = 4 MHz
(PRI_RUN mode)
—
3
mA
+150°C
VDD = 5V, FOSC = 1 MHz
(PRI_RUN mode)
—
8
mA
+150°C
VDD = 5V, FOSC = 64 MHz
(PRI_IDLE mode)
—
1.8
mA
+150°C
VDD = 5V, FOSC = 4 MHz
(PRI_IDLE mode)
—
1
mA
+150°C
VDD = 5V, FOSC = 1 MHz
(PRI_IDLE mode)
—
28
mA
+150°C
VDD = 5V, FOSC = 64 MHz
(PRI_RUN mode, 16 MHz w/PLL)
—
8
mA
+150°C
VDD = 5V, FOSC = 16 MHz
(PRI_RUN mode, 4 MHz w/PLL)
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is
measured with the part in Sleep mode, with all I/O pins in a high-impedance state and tied to VDD or VSS,
and all features that add delta current are disabled (such as WDT, secondary oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as
I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and
temperature, also have an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = External square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT is enabled/disabled as specified.
DS30509A-page 10
2012 Microchip Technology Inc.
PIC18F66K80 FAMILY
3.4
DC Characteristics: PIC18F66K80 Family (High Temperature)
PIC18F66K80 Family
(High Temperature)
Standard Operating Conditions (unless otherwise stated)
Operating temperature +125°C TA +150°C for high temperature
Param
Symbol
No.
Characteristic
Min
Typ
Max
Units
Conditions
D031
VIL
I/O Ports with Schmitt Trigger
Buffer
VSS
—
0.25 VDD
V
VDD = 5.0V
D032
VIL
MCLR
VSS
—
0.25 VDD
V
VDD = 5.0V
D041
VIH
I/O Ports with Schmitt Trigger
Buffer
0.85 VDD
—
VDD
V
VDD = 5.0V
D042
VIH
MCLR, OSC1 (EC mode)
0.85 VDD
—
VDD
V
VDD = 5.0V
D060
IIL
Input Leakage Current
I/O Ports
—
—
±2
µA
VSS ≤ VPIN ≤ VDD,
Pin at high-impedance
3.5
DC Characteristics: Memory Programming Requirements
PIC18F66K80 Family
(High Temperature)
Param
Symbol
No.
Standard Operating Conditions (unless otherwise stated)
Operating temperature +125°C TA +150°C for high temperature
Characteristic
Min
Typ
Max
D120
ED
Data EEPROM Memory Byte
Endurance
50K
—
—
D121
VDRW
VDD for Read/Write
4.0
—
5.5
D123
VRETD
Characteristic Retention
1
—
—
2012 Microchip Technology Inc.
Units
Conditions
E/W +125°C to +150°C
V
Using EECON to read/write
PIC18FXXKXX devices
Year Provided no other specifications
are violated
DS30509A-page 11
PIC18F66K80 FAMILY
3.6
AC Characteristics Internal RC Accuracy (INTOSC)
PIC18F66K80 Family
(High Temperature)
Param
No.
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +150°C
Min
Typ
Max
Units
Conditions
INTOSC Accuracy @ Freq = 16 MHz, 8 MHz, 4 MHz, 2 MHz, 1 MHz, 500 kHz, 250 kHz(1)
OA1
-20
—
±20
%
+125°C to +150°C,
VDD = 4.0-5.5V
—
±25
%
VDD = 4.0-5.5V
OA2 LF_INTOSC Accuracy @ 31 kHz
OA2
Note 1:
-25
Frequency is calibrated at +25°C. The OSCTUNE register can be used to compensate for temperature drift.
TABLE 3-1:
DC CHARACTERISTICS: HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS
PIC18F66K80 Family
(High Temperature)
Param
No.
D420
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +150°C
Characteristic
HLVD Voltage on VDD,
Transition High-to-Low
DS30509A-page 12
Min
Typ
Max
Units
HLVDL = 1101
4.00
4.44
4.88
V
HLVDL = 1110
4.28
4.75
5.23
V
2012 Microchip Technology Inc.
PIC18F66K80
APPENDIX A:
REVISION HISTORY
Revision A (February 2012)
Original mini data sheet for the high-temperature
devices in the PIC18F66K80 family.
DS30509A-page 13
2012 Microchip Technology Inc.
PIC18F66K80
NOTES:
DS30509A-page 14
2012 Microchip Technology Inc.
PIC18F66K80 FAMILY
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
•
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Development Systems Information Line
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://microchip.com/support
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.
2012 Microchip Technology Inc.
DS30509A-page 15
PIC18F66K80 FAMILY
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip
product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our
documentation can better serve you, please FAX your comments to the Technical Publications Manager at
(480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
TO:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Device: PIC18F66K80 Family
Literature Number: DS30509A
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS30509A-page 16
2012 Microchip Technology Inc.
PIC18F66K80 FAMILY
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
X
/XX
XXX
Device
Temperature
Range
Package
Pattern
Device(1,2)
PIC18F25K80/26K80, PIC18F45K80/46K80, PIC18F65K80/66K80,
PIC18F25K80/26K80T, PIC18F45K80/46K80T, PIC18F65K80/
66K80T
VDD range 4.0V to 5.5V
Temperature
Range
I
E
H
=
=
=
Package
PT
MR
SS
MM
ML
=
=
=
=
=
Pattern
-40C to
-40C to
-40C to
+85C
+125C
+150C
Examples:
a)
PIC18F46K80T-H/PT = High Temperature,
TQFP package in tape and reel configuration
(Industrial)
(Extended)
(High Temperature)
TQFP Thin Quad Flatpack
QFN Plastic Quad Flat, No Lead Package
SSOP Plastic Shrink Small Outline
QFN Plastic Quad Flat, No Lead Package
QFN Plastic Quad Flat, No Lead Package
Note 1:
2:
3:
F = Standard Voltage Range
LF = Wide Voltage Range
T = In Tape and Reel PLCC, and TQFP
packages only
QTP, SQTP, Code or Special Requirements
(blank otherwise)
2012 Microchip Technology Inc.
DS30509A-page 17
PIC18F66K80 FAMILY
NOTES:
DS30509A-page 18
2012 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
PIC32 logo, rfPIC and UNI/O are registered trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, chipKIT,
chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net,
dsPICworks, dsSPEAK, ECAN, ECONOMONITOR,
FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP,
Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB,
MPLINK, mTouch, Omniscient Code Generation, PICC,
PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE,
rfLAB, Select Mode, Total Endurance, TSHARC,
UniWinDriver, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2012, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-62076-016-1
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
2012 Microchip Technology Inc.
DS30509A-page 19
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Osaka
Tel: 81-66-152-7160
Fax: 81-66-152-9310
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-330-9305
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
DS30509A-page 20
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
11/29/11
2012 Microchip Technology Inc.
工商网监
湘ICP备2023018690号
