PIC18F97J94T-I/PT

PIC18F97J94 FAMILY 8-Bit LCD Flash Microcontroller with USB and XLP Technology eXtreme Low-Power Features • Multiple Power Management Options for Extreme Power Reduction: - VBAT allows for lowest power consumption on back-up battery (with or without RTCC) - Deep Sleep allows near total power-down with the ability to wake-up on external triggers - Sleep and Idle modes selectively shut down peripherals and/or core for substantial power reduction and fast wake-up • Alternate Clock modes Allow On-the-Fly Switching to a Lower Clock Speed for Selective Power Reduction • Extreme Low-Power Current Consumption for Deep Sleep: - WDT: 650 nA @ 2V typical - RTCC: 650 nA @ 32 kHz, 2V typical - Deep Sleep current, 80 nA typical Universal Serial Bus Features • USB V2.0 Compliant • Low Speed (1.5 Mb/s) and Full Speed (12 Mb/s) • Supports Control, Interrupt, Isochronous and Bulk Transfers • Supports up to 32 Endpoints (16 bidirectional) • USB module can use Any RAM Location on the Device as USB Endpoint Buffers • On-Chip USB Transceiver Peripheral Features • LCD Display Controller: - Up to 60 segments by 8 commons - Internal charge pump and low-power, internal resistor biasing - Operation in Sleep mode • Up to Four External Interrupt Sources • Peripheral Pin Select Lite (PPS-Lite): - Allows independent I/O mapping of many peripherals • Four 16-Bit and Four 8-Bit Timers/Counters with Prescaler • Seven Capture/Compare/PWM (CCP) modules • Three Enhanced Capture/Compare/PWM (ECCP) modules: - One, two or four PWM outputs - Selectable polarity - Programmable dead time - Auto-shutdown and auto-restart - Pulse steering control  2012-2016 Microchip Technology Inc. • Hardware Real-Time Clock/Calendar (RTCC): - Runs in Deep Sleep and VBAT modes • Two Master Synchronous Serial Ports (MSSP) modules Featuring: - 3-Wire/4-Wire SPI (all 4 modes) - SPI Direct Memory Access (DMA) channel w/1024 byte count - Two I2C modules Support Multi-Master/Slave mode and 7-Bit/10-Bit Addressing • Four Enhanced Addressable USART modules: - Support RS-485, RS-232 and LIN/J2602 - On-chip hardware encoder/decoder for IrDA® - Auto-wake-up on Auto-Baud Detect • Digital Signal Modulator Provides On-Chip OOK, FSK and PSK Modulation for a Digital Signal Stream • High-Current Sink/Source 18 mA/18 mA on all Digital I/O • Configurable Open-Drain Outputs on ECCP/CCP/ USART/MSSP • Extended Microcontroller mode Using 12, 16 or 20-Bit Addressing mode Analog Features • 10/12-Bit, 24-Channel Analog-to-Digital (A/D) Converter: - Conversion rate of 500 ksps (10-bit), 200 kbps (12-bit) - Conversion available during Sleep and Idle • Three Rail-to-Rail Enhanced Analog Comparators with Programmable Input/Output Configuration • On-Chip Programmable Voltage Reference • Charge Time Measurement Unit (CTMU): - Used for capacitive touch sensing, up to 24 channels - Time measurement down to 1 ns resolution - CTMU temperature sensing High-Performance CPU • High-Precision PLL for USB • Two External Clock modes, Up to 64 MHz (16 MIPS®) • Internal 31 kHz Oscillator • High-Precision Internal Oscillator with Clock Recovery from SOSC to Achieve 0.15% Precision, 31 kHz to 8 MHz or 64 MHz w/PLL, ±0.15% Typical, ±1.5% Max. • Secondary Oscillator using Timer1 @ 32 kHz • C Compiler Optimized Instruction Set Architecture • Two Address Generation Units for Separate Read and Write Addressing of Data Memory DS30000575C-page 1 PIC18F97J94 FAMILY Special Microcontroller Features • Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) • Brown-out Reset (BOR) with Operation Below VBOR, with Regulator Enabled • High/Low-Voltage Detect (HLVD) • Flexible Watchdog Timer (WDT) with its Own RC Oscillator for Reliable Operation • Standard and Ultra Low-Power Watchdog Timers (WDT) for Reliable Operation in Standard and Deep Sleep modes • Operating Voltage Range of 2.0V to 3.6V • Two On-Chip Voltage Regulators (1.8V and 1.2V) for Regular and Extreme Low-Power Operation • 20,000 Erase/Write Cycle Endurance Flash Program Memory, Typical • Flash Data Retention: 10 Years Minimum • Self-Programmable under Software Control • Two Configurable Reference Clock Outputs (REFO1 and REFO2) • In-Circuit Serial Programming™ (ICSP™) • Fail-Safe Clock Monitor Operation: - Detects clock failure and switches to on-chip, low-power RC oscillator TABLE 1: PIC18F97J94 FAMILY TYPES Flash Program (bytes) Data SRAM (bytes) Timers 8-Bit/16-Bit USART w/IrDA® SPI w/ DMA Comparators CCP/ECCP I2C 10/12-Bit A/D (ch) CTMU LCD (pixels) USB Deep Sleep w/VBAT PPS (Lite) Remappable Peripherals Pins Memory PIC18F97J94 100 128K 4K 4 4 2 3 Y 2 24 Y 480 Y Y Lite PIC18F87J94 80 128K 4K 4 4 2 3 Y 2 24 Y 352 Y Y Lite PIC18F67J94 64 128K 4K 4 4 2 3 Y 2 16 Y 224 Y Y Lite PIC18F96J94 100 64K 4K 4 4 2 3 Y 2 24 Y 480 Y Y Lite PIC18F86J94 80 64K 4K 4 4 2 3 Y 2 24 Y 352 Y Y Lite PIC18F66J94 64 64K 4K 4 4 2 3 Y 2 16 Y 224 Y Y Lite PIC18F95J94 100 32K 4K 4 4 2 3 Y 2 24 Y 480 Y Y Lite PIC18F85J94 80 32K 4K 4 4 2 3 Y 2 24 Y 352 Y Y Lite PIC18F65J94 64 32K 4K 4 4 2 3 Y 2 16 Y 224 Y Y Lite Device For other small form-factor package availability and marking information, visit http://www.microchip.com/packaging or contact your local sales office. DS30000575C-page 2  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY PIN DIAGRAMS 64-PIN TQFP, QFN DIAGRAM FOR PIC18F6XJ94 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 LCDBIAS3/RP30/CS/RE2 COM0/RP33/REFO1/RE3 COM1/RP32/RE4 COM2/RP37/RE5 COM3/RP34/RE6 LCDBIAS0/RP31/RE7 SEG0/RP20/PSP0/RD0 VDD VSS SEG1/RP21/PSP1/RD1 SEG2/RP22/PSP2/RD2 SEG3/RP23/PSP3/RD3 SEG4/RP24/PSP4/RD4 SEG5/SDA2/RP25/PSP5/RD5 SEG6/SCL2/RP26/PSP6/RD6 SEG7/RP27/REFO2/PSP7/RD7 FIGURE 1: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PIC18F6XJ94 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 VLCAP1/RP8/CTED13/INT0/RB0 VLCAP2/RP9/RB1 SEG9/RP14/CTED1/RB2 SEG10/RP7/CTED2/RB3 SEG11/RP12/CTED3/RB4 SEG8/RP13/CTED4/RB5 CTED5/PGC/RB6 VSS OSC2/CLKO/RP6/RA6 OSC1/CLKI/RP10/RA7 VDD CTED6/PGD/RB7 SEG12/RP16/CTED10/RC5 SEG16/SDA1/RP17/CTED9/RC4 SEG17/SCL1/RP15/CTED8/RC3 SEG13/AN9/RP11/CTED7/RC2 VUSB3V3 VBAT AVDD AVSS VREF+/AN3/RP3/RA3 SEG21/VREF-/AN2/RP2/RA2 SEG18/AN1/RP1/RA1 SEG19/AN0/AN1-/RP0/RA0 VSS VDD SEG15/AN4/LVDIN/C1INA/C2INA/C3INA/RP5/RA5 SEG14/AN6/RP4/RA4 SOSCI/RC1 SOSCO/SCLKI/PWRLCLK/RC0 SEG27/RP18/UOE/CTED11/RC6 SEG22/RP19/CTED12/RC7 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 LCDBIAS2/RP29/WR/RE1 LCDBIAS1/RP28/RD/RE0 COM4/SEG28/AN8/RP46/RG0 COM5/SEG29/AN19/RP39/RG1 COM6/SEG30/AN18/C3INA/RP42/RG2 COM7/SEG31/AN17/C3INB/RP43/RG3 MCLR SEG26/AN16/C3INC/RP44/RTCC/RG4 VSS VCAP SEG25/AN5/RP38/RF7 SEG24/AN11/C1INA/RP40/RF6 SEG23/CVREF/AN10/C1INB/RP35/RF5 D+/RF4 D-/RF3 SEG20/AN7/CTMUI/C2INB/RP36/RF2 Note 1: Pinouts are subject to change. 2: See Table 2 for the pin allocation table.  2012-2016 Microchip Technology Inc. DS30000575C-page 3 PIC18F97J94 FAMILY 80-PIN TQFP DIAGRAM FOR PIC18F8XJ94 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 A17/SEG46/AN22/RH1 A16/SEG47/AN23/RH0 AD10/LCDBIAS3/RP30/CS/RE2 AD11/COM0/RP33/REFO1/RE3 AD12/COM1/RP32/RE4 AD13/COM2/RP37/RE5 AD14/COM3/RP34/RE6 AD15/LCDBIAS0/RP31/RE7 AD0/SEG0/RP20/PSP0/RD0 VDD VSS AD1/SEG1/RP21/PSP1/RD1 AD2/SEG2/RP22/PSP2/RD2 AD3/SEG3/RP23/PSP3/RD3 AD4/SEG4/RP24/PSP4/RD4 AD5/SEG5/SDA2/RP25/PSP5/RD5 AD6/SEG6/SCL2/RP26/PSP6/RD6 AD7/SEG7/RP27/REFO2/PSP7/RD7 ALE/SEG32/RJ0 OE/SEG33/RJ1 FIGURE 2: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PIC18F8XJ94 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 WRL/SEG34/RJ2 WRH/SEG35/RJ3 VLCAP1/RP8/CTED13/INT0/RB0 VLCAP2/RP9/RB1 SEG9/RP14/CTED1/RB2 SEG10/RP7/CTED2/RB3 SEG11/RP12/CTED3/RB4 SEG8/RP13/CTED4/RB5 CTED5/PGC/RB6 VSS OSC2/CLKO/RP6/RA6 OSC1/CLKI/RP10/RA7 VDD CTED6/PGD/RB7 SEG12/RP16/CTED10/RC5 SEG16/SDA1/RP17/CTED9/RC4 SEG17/SCL1/RP15/CTED8/RC3 SEG13/AN9/RP11/CTED7/RC2 UB/SEG36/RJ7 LB/SEG37/RJ6 SEG41/AN13/C2IND/RH5 SEG40/AN12/C2INC/RH4 VUSB3V3 VBAT AVDD AVSS VREF+/AN3/RP3/RA3 SEG21/VREF-/AN2/RP2/RA2 SEG18/AN1/RP1/RA1 SEG19/AN0/AN1-/RP0/RA0 Vss VDD SEG15/AN4/LVDIN/C1INA/C2INA/C3INA/RP5/RA5 SEG14/AN6/RP4/RA4 SOSCI/RC1 SOSCO/SCLKI/PWRLCLK/RC0 SEG27/RP18/UOE/CTED11/RC6 SEG22/RP19/CTED12/RC7 BA0/SEG39/RJ4 CE/SEG38/RJ5 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 A18/SEG45/AN21/RH2 A19/SEG44/AN20/RH3 AD9/LCDBIAS2/RP29/WR/RE1 AD8/LCDBIAS1/RP28/RD/RE0 COM4/SEG28/AN8/RP46/RG0 COM5/SEG29/AN19/RP39/RG1 COM6/SEG30/AN18/C3INA/RP42/RG2 COM7/SEG31/AN17/C3INB/RP43/RG3 MCLR SEG26/AN16/C3INC/RP44/RTCC/RG4 VSS VCAP SEG25/AN5/RP38/RF7 SEG24/AN11/C1INA/RP40/RF6 SEG23/CVREF/AN10/C1INB/RP35/RF5 D+/RF4 D-/RF3 SEG20/AN7/C2INB/RP36/RF2 SEG43/AN15/RH7 SEG42/AN14/C1INC/RH6 Note 1: Pinouts are subject to change. 2: See Table 3 for the pin allocation table. DS30000575C-page 4  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 100-PIN TQFP DIAGRAM FOR PIC18F9XJ94 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PIC18F9XJ94 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 WRL/SEG34/RJ2 WRH/SEG35/RJ3 VLCAP1/RP8/CTED13/INT0/RB0 VLCAP2/RP9/RB1 DDIO1/SEG61/RK5 SEG9/RP14/CTED1/RB2 SEG10/RP7/CTED2/RB3 SEG11/RP12/CTED3/RB4 SEG8/RP13/CTED4/RB5 DDIO0/SEG60/RK4 CTED5/PGC/RB6 VSS SEG59/RK3 OSC2/CLKO/RP6/RA6 OSC1/CLKI/RP10/RA7 SEG58/RK2 VDD CTED6/PGD/RB7 SEG12/RP16/CTED10/RC5 SEG16/SDA1/RP17/CTED9/RC4 SEG57/RK1 SEG17/SCL1/RP15/CTED8/RC3 SEG13/AN9/RP11/CTED7/RC2 UB/SEG36/RJ7 LB/SEG37/RJ6 SEG41/AN13/C2IND/RH5 SEG40/AN12/C2INC/RH4 VUSB3V3 VBAT SEG53/RL5 AVDD AVSS VREF+/AN3/RP3/RA3 SEG21/VREF-/AN2/RP2/RA2 VSS SEG18/AN1/RP1/RA1 SEG19/AN0/AN1-/RP0/RA0 SEG54/RL6 VSS VDD SEG55/RL7 SEG15/AN4/LVDIN/C1INA/C2INA/C3INA/RP5/RA5 SEG14/AN6/RP4/RA4 SOSCI/RC1 SOSCO/SCLKI/PWRLCLK/RC0 SEG56/RK0 SEG27/RP18/UOE/CTED11/RC6 SEG22/RP19/CTED12/RC7 BA0/SEG39/RJ4 CE/SEG38/RJ5 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A18/SEG45/AN21/RH2 A19/SEG44/AN20/RH3 AD9/LCDBIAS2/RP29/WR/RE1 AD8/LCDBIAS1/RP28/RD/RE0 VDD COM4/SEG28/AN8/RP46/RG0 COM5/SEG29/AN19/RP39/RG1 COM6/SEG30/AN18/C3INA/RP42/RG2 COM7/SEG31/AN17/C3INB/RP43/RG3 SEG49/RL1 MCLR SEG26/AN16/C3INC/RP44/RTCC/RG4 SEG50/RL2 VSS VCAP SEG51/RL3 SEG25/AN5/RP38/RF7 SEG24/AN11/C1INA/RP40/RF6 SEG23/CVREF/AN10/C1INB/RP35/RF5 D+/RF4 SEG52/RL4 D-/RF3 SEG20/AN7/CTMUI/C2INB/RP36/RF2 SEG43/AN15/RH7 SEG42/AN14/C1INC/RH6 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 A17/SEG46/AN22/RH1 A16/SEG47/AN23/RH0 AD10/LCDBIAS3/RP30/CS/RE2 AD11/COM0/RP33/REFO1/RE3 RG7 AD12/COM1/RP32/RE4 AD13/COM2/RP37/RE5 AD14/COM3/RP34/RE6 AD15/LCDBIAS0/RP31/RE7 SEG48/RL0 AD0/SEG0/RP20/PSP0/RD0 RG6 VDD VSS AD1/SEG1/RP21/PSP1/RD1 SEG63/RK7 AD2/SEG2/RP22/PSP2/RD2 AD3/SEG3/RP23/PSP3/RD3 AD4/SEG4/RP24/PSP4/RD4 AD5/SEG5/SDA2/RP25/PSP5/RD5 SEG62/RK6 AD6/SEG6/SCL2/RP26/PSP6/RD6 AD7/SEG7/RP27/REFO2/PSP7/RD7 ALE/SEG32/RJ0 OE/SEG33/RJ1 FIGURE 3: Note 1: Pinouts are subject to change. 2: See Table 4 for the pin allocation table.  2012-2016 Microchip Technology Inc. DS30000575C-page 5 PIC18F97J94 FAMILY PIN ALLOCATION TABLES USB LCD MSSP PSP Interrupt REFO PPS-Lite(1) Pull-up Basic AN0/ AN1- — — — — SEG19 — — — — RP0 — — ADC CTMU 24 HLVD RA0 Comparator 64-PIN ALLOCATION TABLE (PIC18F6XJ94) 64-Pin TQFP/QFN I/O TABLE 2: RA1 23 AN1 — — — — SEG18 — — — — RP1 — — RA2 22 AN2/ VREF- — — — — SEG21 — — — — RP2 — — RA3 21 AN3/ VREF+ — — — — — — — — — RP3 — — RA4 28 AN6 — — — — SEG14 — — — — RP4 — — RA5 27 AN4 C1INA/ C2INA/ C3INA LVDIN — — SEG15 — — — — RP5 — — RA6 40 — — — — — — — — — — RP6 — OSC2/ CLKO RA7 39 — — — — — — — — — — RP10 — OSC1/ CLKI RB0 48 — — — CTED13 — VLCAP1 — — INT0 — RP8 — — RB1 47 — — — — — VLCAP2 — — — — RP9 — — RB2 46 — — — CTED1 — SEG9 — — — — RP14 — — RB3 45 — — — CTED2 — SEG10 — — — — RP7 — — RB4 44 — — — CTED3 — SEG11 — — — — RP12 — — RB5 43 — — — CTED4 — SEG8 — — — — RP13 — — RB6 42 — — — CTED5 — — — — — — — — PGC RB7 37 — — — CTED6 — — — — — — — — PGD RC0 30 — — — — — — — — — — — — SOSCO/ SCKI/ PWRCLK RC1 29 — — — — — — — — — — — — SOSCI RC2 33 AN9 — — CTED7 — SEG13 — — — — RP11 — — RC3 34 — — — CTED8 — SEG17 SCL1 — — — RP15 — — RC4 35 — — — CTED9 — SEG16 SDA1 — — — RP17 — — RC5 36 — — — CTED10 — SEG12 — — — — RP16 — — RC6 31 — — — CTED11 UOE SEG27 — — — — RP18 — — RC7 32 — — — CTED12 — SEG22 — — — — RP19 — — RD0 58 — — — — — SEG0 — PSP0 — — RP20 Y — RD1 55 — — — — — SEG1 — PSP1 — — RP21 Y — RD2 54 — — — — — SEG2 — PSP2 — — RP22 Y — RD3 53 — — — — — SEG3 — PSP3 — — RP23 Y — RD4 52 — — — — — SEG4 — PSP4 — — RP24 Y — RD5 51 — — — — — SEG5 SDA2 PSP5 — — RP25 Y — RD6 50 — — — — — SEG6 SCL2 PSP6 — — RP26 Y — RD7 49 — — — — — SEG7 — PSP7 — REFO2 RP27 Y — RE0 2 — — — — — LCDBIAS1 — RD — — RP28 Y — RE1 1 — — — — — LCDBIAS2 — WR — — RP29 Y — RE2 64 — — — — — LCDBIAS3 — CS — — RP30 Y — RE3 63 — — — — — COM0 — — — REFO1 RP33 Y — RE4 62 — — — — — COM1 — — — — RP32 Y — RE5 61 — — — — — COM2 — — — — RP37 Y — DS30000575C-page 6  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY Basic Pull-up PPS-Lite(1) REFO Interrupt PSP MSSP LCD USB CTMU HLVD Comparator I/O ADC 64-PIN ALLOCATION TABLE (PIC18F6XJ94) (CONTINUED) 64-Pin TQFP/QFN TABLE 2: RE6 60 — — — — — COM3 — — — — RP34 Y — RE7 59 — — — — — LCDBIAS0 — — — — RP31 Y — RF2 16 AN7 C2INB — CTMUI — SEG20 — — — — RP36 Y — RF3 15 — — — — D- — — — — — — Y — RF4 14 — — — — D+ — — — — — — Y — RF5 13 AN10 C1INB/ CVREF — — — SEG23 — — — — RP35 Y — RF6 12 AN11 C1INA — — — SEG24 — — — — RP40 Y — RF7 11 AN5 — — — — SEG25 — — — — RP38 Y — RG0 3 AN8 — — — — COM4/ SEG28 — — — — RP46 Y — RG1 4 AN19 — — — — COM5/ SEG29 — — — — RP39 Y — RG2 5 AN18 C3INA — — — COM6/ SEG30 — — — — RP42 Y — RG3 6 AN17 C3INB — — — COM7/ SEG31 — — — — RP43 Y — RG4 8 AN16 C3INC — — — SEG26 — — — — RP44 Y — RG5/ MCLR 7 — — — — — — — — — — — Y MCLR AVDD 19 AVDD — — — — — — — — — — — — AVSS 20 AVSS — — — — — — — — — — — — VBAT 18 — — — — — — — — — — — — VBAT VCAP/ VDDCORE 10 — — — — — — — — — — — — VCAP/ VDD 26, 38, 57 — — — — — — — — — — — — VDD VSS 9, 25, 41, 56 — — — — — — — — — — — — VSS VUSB3V3 17 — — — — — — — — — — — — VUSB3V3 Note The peripheral inputs and outputs that support PPS have no default pins. 1: VDDCORE  2012-2016 Microchip Technology Inc. DS30000575C-page 7 PIC18F97J94 FAMILY 80-PIN ALLOCATION TABLE (PIC18F8XJ94) HLVD CTMU USB LCD MSSP PSP Interrupt REFO EMB PPS-Lite(1) Pull-up Basic AN0/ AN1- — — — — SEG19 — — — — — RP0 — — 29 AN1 — — — — SEG18 — — — — — RP1 — — 28 AN2/ VREF- — — — — SEG21 — — — — — RP2 — — 27 AN3/ VREF+ — — — — — — — — — — RP3 — — RA0 30 RA1 RA2 RA3 ADC Comparator 80-Pin TQFP I/O TABLE 3: RA4 34 AN6 — — — — SEG14 — — — — — RP4 — — RA5 33 AN4 C1INA/ C2INA/ C3INA LVDIN — — SEG15 — — — — — RP5 — — RA6 50 — — — — — — — — — — — RP6 — OSC2/ CLKO RA7 49 — — — — — — — — — — — RP10 — OSC1/ CLKI — RB0 58 — — — CTED13 — VLCAP1 — — INT0 — — RP8 — RB1 57 — — — — — VLCAP2 — — — — — RP9 — — RB2 56 — — — CTED1 — SEG9 — — — — — RP14 — — RB3 55 — — — CTED2 — SEG10 — — — — — RP7 — — RB4 54 — — — CTED3 — SEG11 — — — — — RP12 — — RB5 53 — — — CTED4 — SEG8 — — — — — RP13 — — RB6 52 — — — CTED5 — — — — — — — — — PGC RB7 47 — — — CTED6 — — — — — — — — — PGD RC0 36 — — — — — — — — — — — — — SOSCO/ SCKI/ PWRCLK SOSCI RC1 35 — — — — — — — — — — — — — RC2 43 AN9 — — CTED7 — SEG13 — — — — — RP11 — — RC3 44 — — — CTED8 — SEG17 SCL1 — — — — RP15 — — — — RC4 45 — — — CTED9 — SEG16 SDA1 — — — — RP17 RC5 46 — — — CTED10 — SEG12 — — — — — RP16 RC6 37 — — — CTED11 UOE SEG27 — — — — — RP18 — — RC7 38 — — — CTED12 — SEG22 — — — — — RP19 — — RD0 72 — — — — — SEG0 — PSP0 — — AD0 RP20 Y — RD1 69 — — — — — SEG1 — PSP1 — — AD1 RP21 Y — — — — — — SEG2 — PSP2 — — RD2 68 RD3 67 SEG3 PSP3 AD2 RP22 Y — AD3 RP23 Y — RD4 66 — — — — — SEG4 — PSP4 — — AD4 RP24 Y — RD5 65 — — — — — SEG5 SDA2 PSP5 — — AD5 RP25 Y — RD6 64 — — — — — SEG6 SCL2 PSP6 — — AD6 RP26 Y — RD7 63 — — — — — SEG7 — PSP7 — REFO2 AD7 RP27 Y — RE0 4 — — — — — LCDBIAS1 — RD — — AD8 RP28 Y — RE1 3 — — — — — LCDBIAS2 — WR — — AD9 RP29 Y — RE2 78 — — — — — LCDBIAS3 — CS — — AD10 RP30 Y — RE3 77 — — — — — COM0 — — — REFO1 AD11 RP33 Y — RE4 76 — — — — — COM1 — — — — AD12 RP32 Y — RE5 75 — — — — — COM2 — — — — AD13 RP37 Y — RE6 74 — — — — — COM3 — — — — AD14 RP34 Y — RE7 73 — — — — — LCDBIAS0 — — — — AD15 RP31 Y — RF2 18 AN7 C2INB SEG20 — — — — — RP36 Y — DS30000575C-page 8 CTMUI  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY Comparator HLVD CTMU USB LCD MSSP PSP Interrupt REFO EMB PPS-Lite(1) Pull-up Basic RF3 17 — — — — D- — — — — — — — Y — RF4 16 — — — — D+ — — — — — — — Y — RF5 15 AN10 C1INB/ CVREF — — — SEG23 — — — — — RP35 Y — I/O ADC 80-PIN ALLOCATION TABLE (PIC18F8XJ94) (CONTINUED) 80-Pin TQFP TABLE 3: RF6 14 AN11 C1INA — — — SEG24 — — — — — RP40 Y — RF7 13 AN5 — — — — SEG25 — — — — — RP38 Y — RG0 5 AN8 — — — — COM4/ SEG28 — — — — — RP46 Y — RG1 6 AN19 — — — — COM5/ SEG29 — — — — — RP39 Y — RG2 7 AN18 C3INA — — — COM6/ SEG30 — — — — — RP42 Y — RG3 8 AN17 C3INB — — — COM7/ SEG31 — — — — — RP43 Y — RG4 10 AN16 C3INC — — — SEG26 — — — — — RP44 Y — RG5/ MCLR 9 — — — — — — — — — — — — Y MCLR RH0 79 AN23 — — — — SEG47 — — — — A16 — Y — RH1 80 AN22 — — — — SEG46 — — — — A17 — Y — RH2 1 AN21 — — — — SEG45 — — — — A18 — Y — RH3 2 AN20 — — — — SEG44 — — — — A19 — Y — RH4 22 AN12 C2INC — — — SEG40 — — — — — — Y — RH5 21 AN13 C2IND — — — SEG41 — — — — — — Y — RH6 20 AN14 C1INC — — — SEG42 — — — — — — Y — RH7 19 AN15 — — — — SEG43 — — — — — — Y — RJ0 62 — — — — — SEG32 — — — — ALE — Y — RJ1 61 — — — — — SEG33 — — — — OE — Y — RJ2 60 — — — — — SEG34 — — — — WRL — Y — RJ3 59 — — — — — SEG35 — — — — WRH — Y — RJ4 39 — — — — — SEG39 — — — — BA0 — Y — RJ5 40 — — — — — SEG38 — — — — CE — Y — RJ6 41 — — — — — SEG37 — — — — LB — Y — RJ7 42 — — — — — SEG36 — — — — UB — Y — AVDD 25 AVDD — — — — — — — — — — — — — AVSS 26 AVSS — — — — — — — — — — — — — VBAT 24 — — — — — — — — — — — — — VBAT VCAP/ VDDCORE 12 — — — — — — — — — — — — — VCAP/ VDD 32, 48, 71 — — — — — — — — — — — — — VDD VSS 11, 31, 51, 70 — — — — — — — — — — — — — VSS 23 — — — — — — — — — — — — — VUSB3V3 VUSB3V3 Note 1: VDDCORE The peripheral inputs and outputs that support PPS have no default pins.  2012-2016 Microchip Technology Inc. DS30000575C-page 9 PIC18F97J94 FAMILY 100-PIN ALLOCATION TABLE (PIC18F9XJ94) HLVD CTMU USB LCD MSSP PSP Interrupt REFO EMB PPS-Lite(1) Pull-up Basic AN0/ AN1- — — — — SEG19 — — — — — RP0 — — 36 AN1 — — — — SEG18 — — — — — RP1 — — 34 AN2/ VREF- — — — — SEG21 — — — — — RP2 — — 33 AN3/ VREF+ — — — — — — — — — — RP3 — — RA0 37 RA1 RA2 RA3 ADC Comparator 100-Pin TQFP I/O TABLE 4: RA4 43 AN6 — — — — SEG14 — — — — — RP4 — — RA5 42 AN4 C1INA/ C2INA/ C3INA LVDIN — — SEG15 — — — — — RP5 — — RA6 62 — — — — — — — — — — — RP6 — OSC2/ CLKO RA7 61 — — — — — — — — — — — RP10 — OSC1/ CLKI RB0 73 — — — CTED13 — VLCAP1 — — INT0 — — RP8 — — RB1 72 — — — — — VLCAP2 — — — — — RP9 — — RB2 70 — — — CTED1 — SEG9 — — — — — RP14 — — RB3 69 — — — CTED2 — SEG10 — — — — — RP7 — — RB4 68 — — — CTED3 — SEG11 — — — — — RP12 — — RB5 67 — — — CTED4 — SEG8 — — — — — RP13 — — RB6 65 — — — CTED5 — — — — — — — — — PGC RB7 58 — — — CTED6 — — — — — — — — — PGD RC0 45 — — — — — — — — — — — — — SOSCO/ SCKI/ PWRCLK RC1 44 — — — — — — — — — — — — SOSCI RC2 53 AN9 — — CTED7 — SEG13 — — — — — RP11 — — RC3 54 — — — CTED8 — SEG17 SCL1 — — — — RP15 — — RC4 56 — — — CTED9 — SEG16 SDA1 — — — — RP17 — — RC5 57 — — — CTED10 — SEG12 — — — — — RP16 — — RC6 47 — — — CTED11 UOE SEG27 — — — — — RP18 — — RC7 48 — — — CTED12 — SEG22 — — — — — RP19 — — RD0 90 — — — — — SEG0 — PSP0 — — AD0 RP20 Y — RD1 86 — — — — — SEG1 — PSP1 — — AD1 RP21 Y — RD2 84 — — — — — SEG2 — PSP2 — — AD2 RP22 Y — RD3 83 — — — — — SEG3 — PSP3 — — AD3 RP23 Y — RD4 82 — — — — — SEG4 — PSP4 — — AD4 RP24 Y — RD5 81 — — — — — SEG5 SDA2 PSP5 — — AD5 RP25 Y — RD6 79 — — — — — SEG6 SCL2 PSP6 — — AD6 RP26 Y — RD7 78 — — — — — SEG7 — PSP7 — REFO2 AD7 RP27 Y — RE0 4 — — — — — LCDBIAS1 — RD-bar — — AD8 RP28 Y — RE1 3 — — — — — LCDBIAS2 — WRbar — — AD9 RP29 Y — — RE2 98 — — — — — LCDBIAS3 — CS-bar — — AD10 RP30 Y RE3 97 — — — — — COM0 — — — REFO1 AD11 RP33 Y — RE4 95 — — — — — COM1 — — — — AD12 RP32 Y — RE5 94 — — — — — COM2 — — — — AD13 RP37 Y — RE6 93 — — — — — COM3 — — — — AD14 RP34 Y — RE7 92 — — — — — LCDBIAS0 — — — — AD15 RP31 Y — DS30000575C-page 10  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY PPS-Lite(1) — SEG20 — — — — — RP36 Y — — D- — — — — — — — Y — Basic EMB CTMUI — Pull-up LCD — — REFO USB C2INB — Interrupt CTMU AN7 PSP HLVD 23 22 MSSP Comparator RF2 RF3 I/O ADC 100-PIN ALLOCATION TABLE (PIC18F9XJ94) (CONTINUED) 100-Pin TQFP TABLE 4: RF4 20 — — — — D+ — — — — — — — Y — RF5 19 AN10 C1INB/ CVREF — — — SEG23 — — — — — RP35 Y — RF6 18 AN11 C1INA — — — SEG24 — — — — — RP40 Y — RF7 17 AN5 — — — — SEG25 — — — — — RP38 Y — RG0 6 AN8 — — — — COM4/ SEG28 — — — — — RP46 Y — RG1 7 AN19 — — — — COM5/ SEG29 — — — — — RP39 Y — RG2 8 AN18 C3INA — — — COM6/ SEG30 — — — — — RP42 Y — RG3 9 AN17 C3INB — — — COM7/ SEG31 — — — — — RP43 Y — RG4 12 AN16 C3INC — — — SEG26 — — — — — RP44 Y — RG5/ MCLR 11 — — — — — — — — — — — — Y MCLR RG6 89 — — — — — — — — — — — — Y — RG7 96 — — — — — — — — — — — — Y — RH0 99 AN23 — — — — SEG47 — — — — A16 — Y — RH1 100 AN22 — — — — SEG46 — — — — A17 — Y — RH2 1 AN21 — — — — SEG45 — — — — A18 — Y — RH3 2 AN20 — — — — SEG44 — — — — A19 — Y — RH4 27 AN12 C2INC — — — SEG40 — — — — — — Y — RH5 26 AN13 C2IND — — — SEG41 — — — — — — Y — RH6 25 AN14 C1INC — — — SEG42 — — — — — — Y — RH7 24 AN15 — — — — SEG43 — — — — — — Y — RJ0 77 — — — — — SEG32 — — — — ALE — Y — RJ1 76 — — — — — SEG33 — — — — OE — Y — RJ2 75 — — — — — SEG34 — — — — WRL — Y — RJ3 74 — — — — — SEG35 — — — — WRH — Y — RJ4 49 — — — — — SEG39 — — — — BA0 — Y — RJ5 50 — — — — — SEG38 — — — — CE — Y — RJ6 51 — — — — — SEG37 — — — — LB — Y — RJ7 52 — — — — — SEG36 — — — — UB — Y — RK0 46 — — — — — SEG56 — — — — — — Y — RK1 55 — — — — — SEG57 — — — — — — Y — RK2 60 — — — — — SEG58 — — — — — — Y — RK3 63 — — — — — SEG59 — — — — — — Y — RK4 66 — — — — — SEG60 — — — — — — Y — RK5 71 — — — — — SEG61 — — — — — — Y — RK6 80 — — — — — SEG62 — — — — — — Y — RK7 85 — — — — — SEG63 — — — — — — Y — RL0 91 — — — — — SEG48 — — — — — — Y — RL1 10 — — — — — SEG49 — — — — — — Y — RL2 13 — — — — — SEG50 — — — — — — Y — RL3 16 — — — — — SEG51 — — — — — — Y — RL4 21 — — — — — SEG52 — — — — — — Y — RL5 30 — — — — — SEG53 — — — — — — Y —  2012-2016 Microchip Technology Inc. DS30000575C-page 11 PIC18F97J94 FAMILY Basic Pull-up PPS-Lite(1) EMB REFO Interrupt PSP MSSP LCD USB CTMU HLVD Comparator I/O ADC 100-PIN ALLOCATION TABLE (PIC18F9XJ94) (CONTINUED) 100-Pin TQFP TABLE 4: RL6 38 — — — — — SEG54 — — — — — — Y — RL7 41 — — — — — SEG55 — — — — — — Y — — AVDD 31 AVDD — — — — — — — — — — — — AVSS 32 AVSS — — — — — — — — — — — — — VBAT 29 — — — — — — — — — — — — — VBAT VCAP/ VDDCORE 15 — — — — — — — — — — — — — VCAP/ VDDCORE VDD 5, 40, 59, 88 — — — — — — — — — — — — — VDD VSS 14, 35, 39, 64, 87 — — — — — — — — — — — — — VSS VUSB3V3 28 — — — — — — — — — — — — — VUSB3V3 Note The peripheral inputs and outputs that support PPS have no default pins. 1: DS30000575C-page 12  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY Table of Contents 1.0 Device Overview ........................................................................................................................................................................ 15 2.0 Guidelines for Getting Started with PIC18FJ Microcontrollers ................................................................................................... 36 3.0 Oscillator Configurations ............................................................................................................................................................ 41 4.0 Power-Managed Modes ............................................................................................................................................................. 69 5.0 Reset .......................................................................................................................................................................................... 89 6.0 Memory Organization ............................................................................................................................................................... 117 7.0 Flash Program Memory............................................................................................................................................................ 146 8.0 External Memory Bus ............................................................................................................................................................... 156 9.0 8 x 8 Hardware Multiplier.......................................................................................................................................................... 167 10.0 Interrupts .................................................................................................................................................................................. 169 11.0 I/O Ports ................................................................................................................................................................................... 197 12.0 Data Signal Modulator.............................................................................................................................................................. 234 13.0 Liquid Crystal Display (LCD) Controller.................................................................................................................................... 244 14.0 Timer0 Module ......................................................................................................................................................................... 280 15.0 Timer1/3/5 Modules.................................................................................................................................................................. 283 16.0 Timer2/4/6/8 Modules............................................................................................................................................................... 293 17.0 Real-Time Clock and Calendar (RTCC) ................................................................................................................................... 295 18.0 Enhanced Capture/Compare/PWM (ECCP) Module................................................................................................................ 315 19.0 Capture/Compare/PWM (CCP) Modules ................................................................................................................................. 336 20.0 Master Synchronous Serial Port (MSSP) Module .................................................................................................................... 347 21.0 Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) ............................................................... 406 22.0 12-Bit A/D Converter with Threshold Scan............................................................................................................................... 429 23.0 Comparator Module.................................................................................................................................................................. 484 24.0 Comparator Voltage Reference Module ................................................................................................................................... 492 25.0 High/Low-Voltage Detect (HLVD) ............................................................................................................................................. 495 26.0 Charge Time Measurement Unit (CTMU)................................................................................................................................. 500 27.0 Universal Serial Bus (USB) ...................................................................................................................................................... 517 28.0 Special Features of the CPU .................................................................................................................................................... 544 29.0 Instruction Set Summary .......................................................................................................................................................... 565 30.0 Electrical Specifications............................................................................................................................................................ 615 31.0 Development Support............................................................................................................................................................... 648 32.0 DC and AC Characteristics Graphs and Charts ....................................................................................................................... 652 33.0 Packaging Information.............................................................................................................................................................. 653 Appendix A: Revision History............................................................................................................................................................. 667 The Microchip Website....................................................................................................................................................................... 668 Customer Change Notification Service .............................................................................................................................................. 668 Customer Support .............................................................................................................................................................................. 668 Product Identification System ............................................................................................................................................................ 669  2012-2016 Microchip Technology Inc. DS30000575C-page 13 PIC18F97J94 FAMILY TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Website at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Website; http://www.microchip.com • Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our website at www.microchip.com to receive the most current information on all of our products. DS30000575C-page 14  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 1.0 DEVICE OVERVIEW This document contains device-specific information for the following devices: • • • • • PIC18F97J94 PIC18F87J94 PIC18F67J94 PIC18F96J94 PIC18F86J94 • • • • PIC18F66J94 PIC18F95J94 PIC18F85J94 PIC18F65J94 This family introduces a new line of low-voltage LCD microcontrollers with Universal Serial Bus (USB). It combines all the main traditional advantage of all PIC18 microcontrollers, namely, high computational performance and a rich feature set at an extremely competitive price point. These features make the PIC18F9XJ94 family a logical choice for many highperformance applications, where cost is a primary consideration. 1.1 1.1.1 Core Features TECHNOLOGY All of the devices in the PIC18F9XJ94 family incorporate a range of features that can significantly reduce power consumption during operation. Key items include: • Alternate Run Modes: By clocking the controller from the Timer1 source or the Internal RC oscillator, power consumption during code execution can be reduced. • Multiple Idle Modes: The controller can also run with its CPU core disabled but the peripherals still active. In these states, power consumption can be reduced even further. • On-the-Fly Mode Switching: The power-managed modes are invoked by user code during operation, allowing the user to incorporate power-saving ideas into their application’s software design. • XLP: An extra low-power Sleep, BOR, RTCC and Watchdog Timer.  2012-2016 Microchip Technology Inc. 1.1.2 OSCILLATOR OPTIONS AND FEATURES All of the devices in the PIC18F9XJ94 family offer different oscillator options, allowing users a range of choices in developing application hardware. These include: • Two Crystal modes (HS, MS) • One External Clock mode (EC) • A Phase Lock Loop (PLL) frequency multiplier, which allows clock speeds of up to 64 MHz. • A fast Internal Oscillator (FRC) block that provides an 8 MHz clock (±0.15% accuracy) with Active Clock Tuning (ACT) from USB or SOSC source. - Offers multiple divider options from 8 MHz to 500 kHz - Frees the two oscillator pins for use as additional general purpose I/O • A separate Low-Power Internal RC Oscillator (LPRC) (31 kHz nominal) for low-power, timinginsensitive applications. The internal oscillator block provides a stable reference source that gives the family additional features for robust operation: • Fail-Safe Clock Monitor (FSCM): This option constantly monitors the main clock source against a reference signal provided by the internal oscillator. If a clock failure occurs, the controller is switched to the internal oscillator, allowing for continued lowspeed operation or a safe application shutdown. • Two-Speed Start-up (IESO): This option allows the internal oscillator to serve as the clock source from Power-on Reset, or wake-up from Sleep mode, until the primary clock source is available. DS30000575C-page 15 PIC18F97J94 FAMILY 1.1.3 MEMORY OPTIONS The PIC18F9XJ94 family provides ample room for application code, from 32 Kbytes to 128 Kbytes of code space. The Flash cells for program memory are rated to last up to 20,000 erase/write cycles. Data retention without refresh is conservatively estimated to be greater than 10 years. The Flash program memory is readable and writable. During normal operation, the PIC18F9XJ94 family also provides plenty of room for dynamic application data with up to 3,578 bytes of data RAM. 1.1.4 UNIVERSAL SERIAL BUS (USB) Devices in the PIC18F9XJ94 family incorporate a fullyfeatured USB communications module with a built-in transceiver that is compliant with the USB Specification Revision 2.0. The module supports both low-speed and full-speed communication for all supported data transfer types. 1.1.5 EXTERNAL MEMORY BUS Should 128 Kbytes of memory be inadequate for an application, the 80-pin and 100-pin members of the PIC18F9XJ94 family have an External Memory Bus (EMB), enabling the controller’s internal Program Counter to address a memory space of up to 2 Mbytes. This is a level of data access that few 8-bit devices can claim and enables: • Using combinations of on-chip and external memory of up to 2 Mbytes • Using external Flash memory for reprogrammable application code or large data tables • Using external RAM devices for storing large amounts of variable data DS30000575C-page 16 1.1.6 EXTENDED INSTRUCTION SET The PIC18F9XJ94 family implements the optional extension to the PIC18 instruction set, adding eight new instructions and an Indexed Addressing mode. Enabled as a device configuration option, the extension has been specifically designed to optimize re-entrant application code originally developed in high-level languages, such as ‘C’. 1.1.7 EASY MIGRATION All devices share the same rich set of peripherals. This provides a smooth migration path within the device family as applications evolve and grow. The consistent pinout scheme, used throughout the entire family, also aids in migrating to the next larger device. This is true when moving between the 64-pin members, between the 80-pin members, between the 100-pin members or even jumping from 64-pin to 80pin to 100-pin devices. The PIC18F9XJ94 family is also largely pin compatible with other PIC18 families, such as the PIC18F87J90, PIC18F87J11 and the PIC18F87J50. This allows a new dimension to the evolution of applications, allowing developers to select different price points within Microchip’s PIC18 portfolio, while maintaining a similar feature set. 1.2 LCD Controller The on-chip LCD driver includes many features that make the integration of displays in low-power applications easier. These include an integrated voltage regulator with charge pump and an integrated internal resistor ladder that allows contrast control in software and display operation above device VDD.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 1.3 Other Special Features • Communications: The PIC18F9XJ94 family incorporates a range of serial communication peripherals, including USB, four Enhanced Addressable USARTs with IrDA, and two Master Synchronous Serial Port MSSP modules capable of both SPI and I2C (Master and Slave) modes of operation. • CCP Modules: PIC18F9XJ94 family devices incorporate up to seven Capture/Compare/PWM (CCP) modules. Up to six different time bases can be used to perform several different operations at once. • ECCP Modules: The PIC18F9XJ94 family has three Enhanced CCP (ECCP) modules to maximize flexibility in control applications: - Up to eight different time bases for performing several different operations at once - Up to four PWM outputs for each module – for a total of 12 PWMs - Other beneficial features, such as polarity selection, programmable dead time, autoshutdown and restart, and Half-Bridge and Full-Bridge Output modes • 12-Bit A/D Converter: The PIC18F9XJ94 family has a software selectable, 10/12-bit Analog-to-Digital (A/D) Converter. It incorporates programmable acquisition time, allowing for a channel to be selected and a conversion to be initiated without waiting for a sampling period, and thus, reducing code overhead. • Charge Time Measurement Unit (CTMU): The CTMU is a flexible analog module that provides accurate differential time measurement between pulse sources, as well as asynchronous pulse generation. • Together with other on-chip analog modules, the CTMU can precisely measure time, measure capacitance or relative changes in capacitance, or generate output pulses that are independent of the system clock. • LP Watchdog Timer (WDT): This enhanced version incorporates a 22-bit prescaler, allowing an extended time-out range that is stable across operating voltage and temperature. See Section 30.0 “Electrical Specifications” for time-out periods. • Real-Time Clock and Calendar Module (RTCC): The RTCC module is intended for applications requiring that accurate time be maintained for extended periods of time, with minimum to no intervention from the CPU. • The module is a 100-year clock and calendar with automatic leap year detection. The range of the clock is from 00:00:00 (midnight) on January 1, 2000 to 23:59:59 on December 31, 2099.  2012-2016 Microchip Technology Inc. 1.4 Details on Individual Family Members Devices in the PIC18F9XJ94 family are available in 64pin, 80-pin and 100-pin packages. Block diagrams for the two groups are shown in Figure 1-1, Figure 1-2 and Figure 1-3. The devices are differentiated from each other in these ways: • Flash Program Memory: - PIC18FX5J94 – 32 Kbytes - PIC18FX6J94 – 64 Kbytes - PIC18FX7J94 – 128 Kbytes • Data RAM: - All devices – 4 Kbytes • I/O Ports: - PIC18F6XJ9X (64-pin devices) – seven bidirectional ports - PIC18F8XJ9X (80-pin devices) – nine bidirectional ports - PIC18F9XJ9X (100-pin devices) – eleven bidirectional ports • A/D Channels: - PIC18F6XJXX (64-pin devices) – 16 channels - PIC18F8XJXX (80-pin devices) – 24 channels - PIC18F9XJXX (100-pin devices) – 24 channels All other features for devices in this family are identical. These are summarized in Table 1-1, Table 1-2 and Table 1-3. The pinouts for all devices are listed in Table 1-4. DS30000575C-page 17 PIC18F97J94 FAMILY TABLE 1-1: DEVICE FEATURES FOR THE 64-PIN DEVICES Features PIC18F65J94 PIC18F66J94 Operating Frequency Program Memory (Bytes) Program Memory (Instructions) PIC18F67J94 DC – 64 MHz 32K 64K 128K 16,384 32,768 65,536 Data Memory (Bytes) 4K 4K 4K Interrupt Sources 42 48 I/O Ports Ports A, B, C, D, E, F, G Parallel Communications Parallel Slave Port (PSP) Timers 8 Comparators 3 LCD 224 pixels CTMU Yes RTCC Yes Enhanced Capture/Compare/PWM Modules Serial Communications 3 ECCPs and 7 CCPs Two MSSPs, Four Enhanced USARTs (EUSART) and USB 10/12-Bit Analog-to-Digital Module Resets (and Delays) Instruction Set 16 Input Channels POR, BOR, CM RESET Instruction, Stack Full, Stack Underflow, MCLR, WDT (PWRT, OST) 75 Instructions, 83 with Extended Instruction Set Enabled Packages TABLE 1-2: 64-Pin QFN, 64-Pin TQFP DEVICE FEATURES FOR THE 80-PIN DEVICES Features PIC18F85J94 Operating Frequency Program Memory (Bytes) Program Memory (Instructions) PIC18F86J94 DC – 64 MHz 32 K 64K 16,384 32,768 4K 4K Interrupt Sources 42 Parallel Communications Timers Comparators LCD 4K Ports A, B, C, D, E, F, G, H, J Parallel Slave Port (PSP) 8 3 352 pixels Yes RTCC Yes Serial Communications 12-Bit Analog-to-Digital Module Resets (and Delays) Instruction Set Packages DS30000575C-page 18 65,536 48 CTMU Enhanced Capture/Compare/PWM Modules 128K (Up to 2 Mbytes with Extended Memory) Data Memory (Bytes) I/O Ports PIC18F87J94 3 ECCPs and 7 CCPs Two MSSPs, Four Enhanced USARTs (EUSART) and USB 24 Input Channels POR, BOR, CM RESET Instruction, Stack Full, Stack Underflow, MCLR, WDT (PWRT, OST) 75 Instructions, 83 with Extended Instruction Set Enabled 80-Pin TQFP  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 1-3: DEVICE FEATURES FOR THE 100-PIN DEVICES Features PIC18F95J94 Operating Frequency Program Memory (Bytes) Program Memory (Instructions) PIC18F96J94 DC – 64 MHz 32 K 64K 32,768 Data Memory (Bytes) 4K 4K Interrupt Sources 42 Parallel Communications 4K Ports A, B, C, D, E, F, G, H, J, K, L Parallel Slave Port (PSP) 8 Comparators 3 CTMU RTCC Enhanced Capture/Compare/PWM Modules Serial Communications 12-Bit Analog-to-Digital Module Resets (and Delays) Instruction Set Packages  2012-2016 Microchip Technology Inc. 65,536 48 Timers LCD 128K (Up to 2 Mbytes with Extended Memory) 16,384 I/O Ports PIC18F97J94 480 pixels Yes Yes 3 ECCPs and 7 CCPs Two MSSPs, Four Enhanced USARTs (EUSART) and USB 24 Input Channels POR, BOR, CM RESET Instruction, Stack Full, Stack Underflow, MCLR, WDT (PWRT, OST) 75 Instructions, 83 with Extended Instruction Set Enabled 100-Pin TQFP DS30000575C-page 19 PIC18F97J94 FAMILY FIGURE 1-1: 64-PIN DEVICE BLOCK DIAGRAM Data Bus Table Pointer 20 Address Latch PCU PCH PCL Program Counter 12 Data Address 31-Level Stack 4 BSR Address Latch STKPTR Program Memory RB(1) 12 PORTC RC(1) inc/dec logic Table Latch Instruction Bus PORTB 4 Access Bank 12 FSR0 FSR1 FSR2 Data Latch 8 RA(1,2) Data Memory (4 Kbytes) PCLATU PCLATH 21 PORTA Data Latch 8 8 inc/dec logic Address Decode ROM Latch PORTD RD(1) IR OSC2/CLKO OSC1/CLKI Timing Generation PRODH PRODL W 8 8 8 8 Power-on Reset Precision Band Gap Reference 8 BITOP Oscillator Start-up Timer PORTE RE(1) 8 x 8 Multiply 3 Power-up Timer INTRC Oscillator 8 MHz Oscillator 8 State Machine Control Signals Instruction Decode and Control PORTF 8 RF(1) ALU Watchdog Timer 8 BOR and HLVD Voltage Regulator PORTG RG(1) VDDCORE/VCAP VDD, VSS MCLR Timer0 Timer1 Timer 2/4/6/8 Timer 3/5 CCP 4/5/6/7/8/9/10 ECCP 1/2/3 EUSART1 EUSART2 Note 1: 2: CTMU RTCC A/D 10/12-Bit MSSP1/2 LCD 224 Pixels USB Comparator 1/2/3 EUSART3 EUSART4 See Table 1-4 for I/O port pin descriptions. RA6 and RA7 are only available as digital I/O in select oscillator modes. For more information, see Section 3.0 “Oscillator Configurations”. DS30000575C-page 20  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 1-2: 80-PIN DEVICE BLOCK DIAGRAM Data Bus Table Pointer 8 8 inc/dec logic 20 Address Latch PCU PCH PCL Program Counter 31-Level Stack 4 BSR System Bus Interface STKPTR FSR0 FSR1 FSR2 Table Latch RD(1) Address Decode Instruction Bus PORTE RE(1) IR AD, A (Multiplexed with PORTD, PORTE and PORTH) Instruction Decode and Control Timing Generation Power-up Timer INTRC Oscillator 8 MHz Oscillator Oscillator Start-up Timer Watchdog Timer Voltage Regulator BOR and HLVD VDD, VSS RF(1) PRODH PRODL 3 PORTG 8 x 8 Multiply RG(1) 8 BITOP W 8 8 8 8 Power-on Reset Precision Band Gap Reference PORTF 8 State Machine Control Signals PORTH RH(1) 8 ALU PORTJ 8 RJ(1) MCLR Timer0 Timer1 Timer 2/4/6/8 Timer 3/5 CTMU A/D 12-Bit CCP 4/5/6/7/8/9/10 ECCP 1/2/3 EUSART1 EUSART2 RTCC MSSP1/2 2: 12 PORTD ROM Latch Note 1: RC(1) inc/dec logic 8 VDDCORE/VCAP PORTC 4 Access Bank 12 Data Latch OSC2/CLKO OSC1/CLKI PORTB RB(1) 12 Data Address Address Latch Program Memory RA(1,2) Data Memory (4 Kbytes) PCLATU PCLATH 21 PORTA Data Latch USB LCD 352 Pixels Comparator 1/2/3 EUSART4 EUSART3 USB EMB See Table 1-4 for I/O port pin descriptions. RA6 and RA7 are only available as digital I/O in select oscillator modes. See Section 3.0 “Oscillator Configurations” for more information.  2012-2016 Microchip Technology Inc. DS30000575C-page 21 PIC18F97J94 FAMILY FIGURE 1-3: 100-PIN DEVICE BLOCK DIAGRAM Data Bus Table Pointer 8 8 inc/dec logic 20 PORTB 12 Data Address 31-Level Stack 4 BSR Address Latch STKPTR 12 RB(1) 4 Access Bank FSR0 FSR1 FSR2 Data Latch 8 RA(1,2) Address Latch PCU PCH PCL Program Counter Program Memory PORTA Data Memory (4 Kbytes) PCLATU PCLATH 21 System Bus Interface Data Latch USB PORTC RC(1) 12 PORTD inc/dec logic Table Latch RD(1) Address Decode ROM Latch Instruction Bus PORTE RE(1) IR AD, A (Multiplexed with PORTD, PORTE and PORTH) Instruction Decode and Control OSC2/CLKO OSC1/CLKI Timing Generation Power-up Timer INTRC Oscillator 8 MHz Oscillator Oscillator Start-up Timer Watchdog Timer Voltage Regulator BOR and HLVD VDD, VSS PORTF RF(1) PRODH PRODL 3 PORTG 8 x 8 Multiply 8 BITOP W RG, RG(1) 8 8 8 PORTH 8 Power-on Reset Precision Band Gap Reference VDDCORE/VCAP 8 State Machine Control Signals 8 RH(1) ALU 8 PORTJ RJ(1) PORTK MCLR RK(1) Timer0 Timer1 CCP 4/5/6/7/8/9/10 Note 1: 2: ECCP 1/2/3 Timer 2/4/6/8 Timer 3/5 CTMU EUSART1 EUSART2 RTCC A/D 12-Bit MSSP1/2 LCD 480 Pixels PORTL Comparator 1/2/3 EUSART4 EUSART3 USB RL(1) EMB See Table 1-4 for I/O port pin descriptions. RA6 and RA7 are only available as digital I/O in select oscillator modes. See Section 3.0 “Oscillator Configurations” for more information. DS30000575C-page 22  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS Pin Name Pin Number Pin 100 80 64 Type MCLR 11 9 7 OSC1/CLKI/RP10/RA7 61 49 39 I OSC1 CLKI I I RP10 RA7 I/O I/O OSC2/CLKO/RP6/RA6 62 50 40 OSC2 O CLKO O RP6 RA6 I/O I/O Legend: TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus  2012-2016 Microchip Technology Inc. Buffer Type ST Description Master Clear (input) or programming voltage (input). This pin is an active-low Reset to the device. Oscillator crystal or external clock input. Oscillator crystal input. External clock source input. Always associated with pin function, OSC1. (See related OSC1/CLKI,OSC2/CLKO pins.) ST/DIG Remappable Peripheral Pin 10 input/output. ST/DIG General purpose I/O pin. ST CMOS Oscillator crystal or clock output. Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. DIG In certain oscillator modes, OSC2 pin outputs CLKO, which has 1/4 the frequency of OSC1 and denotes the instruction cycle rate. ST/DIG Remappable Peripheral Pin 6 input/output. ST/DIG General purpose I/O pin. — CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD) DS30000575C-page 23 PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name SEG19/AN0/AN1-/RP0/RA0 Pin Number Pin 100 80 64 Type 37 36 34 33 43 SEG15 AN4 LVDIN C1INA C2INA C3INA RP5 RA5 Legend: 42 O I I/O I/O Analog Analog ST/DIG ST/DIG SEG18 output for LCD. Analog Input 1. Remappable Peripheral Pin 1 input/output. General purpose I/O pin. O I I I/O I/O Analog Analog Analog ST/DIG ST/DIG SEG21 output for LCD. A/D reference voltage (low) input. Analog Input 2. Remappable Peripheral Pin 2 input/output. General purpose I/O pin. I I I/O I/O Analog Analog ST/DIG ST/DIG A/D reference voltage (high) input. Analog Input 3. Remappable Peripheral Pin 3 input/output. General purpose I/O pin. O I I/O I/O Analog Analog ST/DIG ST/DIG SEG14 output for LCD. Analog Input 6. Remappable Peripheral Pin 4 input/output. General purpose I/O pin. O I I I I I I/O I/O Analog Analog Analog Analog Analog Analog ST/DIG ST/DIG SEG15 output for LCD. Analog Input 4. High/Low-Voltage Detect (HLVD) input. Comparator 1 Input A. Comparator 2 Input A. Comparator 3 Input A. Remappable Peripheral Pin 5 input/output. General purpose I/O pin. 34 28 SEG14 AN6 RP4 RA4 SEG15/AN4/LVDIN/C1INA/ C2INA/C3INA/RP5/RA5 SEG19 output for LCD. Analog Input 0. A/D negative input channel. Remappable Peripheral Pin 0 input/output. General purpose I/O pin. 27 21 VREF+ AN3 RP3 RA3 SEG14/AN6/RP4/RA4 Analog Analog Analog ST/DIG ST/DIG 28 22 SEG21 VREFAN2 RP2 RA2 VREF+/AN3/RP3/RA3 O I I I/O I/O 29 23 SEG18 AN1 RP1 RA1 SEG21/VREF-/AN2/RP2/RA2 33 27 TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus DS30000575C-page 24 Description 30 24 SEG19 AN0 AN1RP0 RA0 SEG18/AN1/RP1/RA1 Buffer Type CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name VLCAP1/RP8/CTED13/INT0/RB0 Pin Number Pin 100 80 64 Type 73 72 70 69 68 67 65 58 PGD CTED6 RB7 Legend: O I/O I I/O Analog ST/DIG ST ST/DIG SEG9 output for LCD. Remappable Peripheral Pin 14 input/output. CTMU Edge 1 input. General purpose I/O pin. O I/O I I/O Analog ST/DIG ST ST/DIG SEG10 output for LCD. Remappable Peripheral Pin 7 input/output. CTMU Edge 2 input. General purpose I/O pin. O I/O I I/O Analog ST/DIG ST ST/DIG SEG11 output for LCD. Remappable Peripheral Pin 12 input/output. CTMU Edge 3 input. General purpose I/O pin. O I/O I I/O Analog ST/DIG ST ST/DIG SEG8 output for LCD. Remappable Peripheral Pin 13 input/output. CTMU Edge 4 input. General purpose I/O pin. I/O I I/O ST/DIG In-Circuit Debugger and ICSP™ programming clock pin. ST CTMU Edge Input. ST/DIG General purpose I/O pin. I/O I I/O ST/DIG In-Circuit Debugger and ICSP™ programming data pin. ST CTMU Edge 6 input. ST/DIG General purpose I/O pin. 52 42 PGC CTED5 RB6 PGD/CTED6/RB7 Analog LCD Drive Charge Pump Capacitor Input 2. ST/DIG Remappable Peripheral Pin 9 input/output. ST/DIG General purpose I/O pin. 53 43 SEG8 RP13 CTED4 RB5 PGC/CTED5/RB6 I I/O I/O 54 44 SEG11 RP12 CTED3 RB4 SEG8/RP13/CTED4/RB5 47 37 TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus  2012-2016 Microchip Technology Inc. LCD Drive Charge Pump Capacitor Input 1. Remappable Peripheral Pin 8 input/output. CTMU Edge 13 input. External Interrupt 0. General purpose I/O pin. 55 45 SEG10 RP7 CTED2 RB3 SEG11/RP12/CTED3/RB4 Analog ST/DIG ST ST ST/DIG 56 46 SEG9 RP14 CTED1 RB2 SEG10/RP7/CTED2/RB3 I I/O I I I/O 57 47 VLCAP2 RP9 RB1 SEG9/RP14/CTED1/RB2 Description 58 48 VLCAP1 RP8 CTED13 INT0 RB0 VLCAP2/RP9/RB1 Buffer Type CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD) DS30000575C-page 25 PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name SOSCO/SCLKI/PWRLCLK/RC0 Pin Number Pin 100 80 64 Type 45 Buffer Type Description 36 30 SOSCO SCLKI PWRLCLK O I I — ST ST RC0 I/O ST I I/O Analog ST Timer1 oscillator input. General purpose Input pin. O I I/O I I/O Analog Analog ST/DIG ST ST/DIG SEG13 output for LCD. Analog Input 9. Remappable Peripheral Pin 11 input/output. CTMU Edge 7 input. General purpose I/O pin. O I/O I/O I I/O Analog I2C ST/DIG ST ST/DIG SEG17 output for LCD. I2C clock input/output. Remappable Peripheral Pin 15 input/output. CTMU Edge 8 input. General purpose I/O pin. O I/O I/O I I/O Analog I2C ST/DIG ST ST/DIG SEG16 output for LCD. I2C data input/output. Remappable Peripheral Pin 17 input/output. CTMU Edge 9 input. General purpose I/O pin. O I/O I I/O Analog ST/DIG ST ST/DIG SEG12 output for LCD. Remappable Peripheral Pin 16 input/output. CTMU Edge 10 input. General purpose I/O pin. O I/O O I I/O Analog ST/DIG DIG ST ST/DIG SEG27 output for LCD. Remappable Peripheral Pin 18 input/output. External USB transceiver NOE output. CTMU Edge 11 input. General purpose I/O pin. O I/O I I/O Analog ST/DIG ST ST/DIG SEG22 output for LCD. Remappable Peripheral Pin 19 input/output. CTMU Edge 12 input. General purpose I/O pin. SOSCI/RC1 44 35 29 SOSCI RC1 SEG13/AN9/RP11/CTED7/RC2 53 43 33 SEG13 AN9 RP11 CTED7 RC2 SEG17/SCL1/RP15/CTED8/RC3 54 44 34 SEG17 SCL1 RP15 CTED8 RC3 SEG16/SDA1/RP17/CTED9/RC4 56 45 35 SEG16 SDA1 RP17 CTED9 RC4 SEG12/RP16/CTED10/RC5 57 46 36 SEG12 RP16 CTED10 RC5 SEG27/RP18/UOE/CTED11/RC6 47 37 31 SEG27 RP18 UOE/ CTED11 RC6 SEG22/RP19/CTED12/RC7 SEG22 RP19 CTED12 RC7 Legend: 48 38 32 TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus DS30000575C-page 26 SOSC oscillator output. Digital SOSC input. SOSC input at 50 Hz or 60 Hz only (RTCCLKSEL = 11 or 10). General purpose Input pin. CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name AD0/SEG0/RP20/PSP0/RD0 Pin Number Pin 100 80 64 Type 90 86 84 83 82 81 79 78 AD7 SEG7 RP27 REFO2 PSP7 RD7 Legend: External Memory Address/Data 1. SEG1 output for LCD. Remappable Peripheral Pin 21 input/output. Parallel Slave Port data. General purpose I/O pin. I/O O I/O I/O I/O TTL/DIG Analog ST/DIG ST/DIG ST/DIG External Memory Address/Data 2. SEG2 output for LCD. Remappable Peripheral Pin 22 input/output. Parallel Slave Port data. General purpose I/O pin. I/O O I/O I/O I/O TTL/DIG Analog ST/DIG ST/DIG ST/DIG External Memory Address/Data 3. SEG3 output for LCD. Remappable Peripheral Pin 3 input/output. Parallel Slave Port data. General purpose I/O pin. I/O O I/O I/O I/O TTL/DIG Analog ST/DIG ST/DIG ST/DIG External Memory Address/Data 4. SEG4 output for LCD. Remappable Peripheral Pin 24 input/output. Parallel Slave Port data. General purpose I/O pin. I/O O I/O I/O I/O I/O TTL/DIG Analog I2C ST/DIG ST/DIG ST/DIG External Memory Address/Data 5. SEG5 output for LCD. I2C data input/output. Remappable Peripheral Pin 25 input/output. Parallel Slave Port data. General purpose I/O pin. I/O O I/O I/O I/O I/O TTL/DIG Analog I2C ST/DIG ST/DIG ST/DIG External Memory Address/Data 6. SEG6 output for LCD. I2C clock input/output. Remappable Peripheral Pin 26 input/output. Parallel Slave Port data. General purpose I/O pin. I/O O I/O O I/O I/O TTL/DIG Analog ST/DIG DIG ST/DIG ST/DIG External Memory Address/Data 7. SEG7 output for LCD. Remappable Peripheral Pin 27 input/output. Reference output clock. Parallel Slave Port data General purpose I/O pin. 64 50 AD6 SEG6 SCL2 RP26 PSP6 RD6 AD7/SEG7/RP27/REFO2/ PSP7/RD7 TTL/DIG Analog ST/DIG ST/DIG ST/DIG 65 51 AD5 SEG5 SDA2 RP25 PSP5 RD5 AD6/SEG6/SCL2/RP26/PSP6/RD6 I/O O I/O I/O I/O 66 52 AD4 SEG4 RP24 PSP4 RD4 AD5/SEG5/SDA2/RP25/PSP5/RD5 External Memory Address/Data 0. SEG0 output for LCD. Remappable Peripheral Pin 20 input/output. Parallel Slave Port data. General purpose I/O pin. 67 53 AD3 SEG3 RP23 PSP3 RD3 AD4/SEG4/RP24/PSP4/RD4 TTL/DIG Analog ST/DIG ST/DIG ST/DIG 68 54 AD2 SEG2 RP22 PSP2 RD2 AD3/SEG3/RP23/PSP3/RD3 I/O O I/O I/O I/O 69 55 AD1 SEG1 RP21 PSP1 RD1 AD2/SEG2/RP22/PSP2/RD2 63 49 TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus  2012-2016 Microchip Technology Inc. Description 72 58 AD0 SEG0 RP20 PSP0 RD0 AD1/SEG1/RP21/PSP1/RD1 Buffer Type CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD) DS30000575C-page 27 PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name AD8/LCDBIAS1/RP28/RD/RE0 Pin Number Pin 100 80 64 Type 4 4 3 3 98 97 95 94 93 AD15 LCDBIAS0 RP31 RE7 Legend: 92 External Memory Address/Data 9. BIAS2 input for LCD. Remappable Peripheral Pin 29 input/output. Parallel Slave Port write strobe. General purpose I/O pin. I/O I I/O I I/O TTL/DIG Analog ST/DIG TTL ST/DIG External Memory Address/Data 10. BIAS3 input for LCD. Remappable Peripheral Pin 30 input/output. Parallel Slave Port chip select. General purpose I/O pin. I/O O I/O O I/O TTL/DIG Analog ST/DIG DIG ST/DIG External Memory Address/Data 11. COM0 output for LCD. Remappable Peripheral Pin 33 input/output. Reference output clock. General purpose I/O pin. I/O O I/O I/O TTL/DIG Analog ST/DIG ST/DIG External Memory Address/Data 12. COM1 output for LCD. Remappable Peripheral Pin 32 input/output. General purpose I/O pin. I/O O I/O I/O TTL/DIG Analog ST/DIG ST/DIG External Memory Address/Data 13. COM2 output for LCD. Remappable Peripheral Pin 37 input/output. General purpose I/O pin. I/O O I/O I/O TTL/DIG Analog ST/DIG ST/DIG External Memory Address/Data 14. COM3 output for LCD. Remappable Peripheral Pin 34 input/output. General purpose I/O pin. I/O I I/O I/O TTL/DIG Analog ST/DIG ST/DIG External Memory Address/Data 15. BIAS0 input for LCD. Remappable Peripheral Pin 31 input/output. General purpose I/O pin. 74 60 AD14 COM3 RP34 RE6 AD15/LCDBIAS0/RP31/RE7 TTL/DIG Analog ST/DIG TTL ST/DIG 75 61 AD13 COM2 RP37 RE5 AD14/COM3/RP34/RE6 I/O I I/O I I/O 76 62 AD12 COM1 RP32 RE4 AD13/COM2/RP37/RE5 External Memory Address/Data 8. BIAS1 input for LCD. Remappable Peripheral Pin 28 input/output. Parallel Slave Port read strobe. General purpose I/O pin. 77 63 AD11 COM0 RP33 REFO1 RE3 AD12/COM1/RP32/RE4 TTL/DIG Analog ST/DIG TTL ST/DIG 78 64 AD10 LCDBIAS3 RP30 CS RE2 AD11/COM0/RP33/REFO1/RE3 I/O I I/O I I/O 1 AD9 LCDBIAS2 RP29 WR RE1 AD10/LCDBIAS3/RP30/CS/RE2 73 59 TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus DS30000575C-page 28 Description 2 AD8 LCDBIAS1 RP28 RD RE0 AD9/LCDBIAS2/RP29/WR/RE1 Buffer Type CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name SEG20/AN7/CTMUI/C2INB/RP36/ RF2 Pin Number Pin 100 80 64 Type 23 22 20 19 18 17 SEG25 AN5 RP38 RF7 Legend: I/O I — ST USB bus minus line input/output. General purpose input pin. I/O I — ST USB bus plus line input/output. General purpose input pin. O O I I I/O I/O Analog Analog Analog Analog ST/DIG ST/DIG SEG23 output for LCD. Comparator reference voltage output. Analog Input 10. Comparator 1 Input B. Remappable Peripheral Pin 35 input/output. General purpose I/O pin. O I I I/O I/O Analog Analog Analog ST/DIG ST/DIG SEG24 output for LCD. Analog Input 11. Comparator 1 Input A. Remappable Peripheral Pin 40 input/output. General purpose I/O pin. O I I/O I/O Analog Analog ST/DIG ST/DIG SEG25 output for LCD. Analog Input 5. Remappable Peripheral Pin 38 input/output. General purpose I/O pin. 14 12 SEG24 AN11 C1INA RP40 RF6 SEG25/AN5/RP38/RF7 SEG20 output for LCD. Analog Input 7. CTMU pulse generator charger for the C2INB comparator input. Comparator 2 Input B. Remappable Peripheral Pin 36 input/output. General purpose I/O pin. 15 13 SEG23 CVREF AN10 C1INB RP35 RF5 SEG24/AN11/C1INA/RP40/RF6 Analog Analog — Analog ST/DIG ST/DIG 16 14 D+ RF4 SEG23/CVREF/AN10/C1INB/ RP35/RF5 O I O I I/O I/O 17 15 DRF3 D+/RF4 Description 18 16 SEG20 AN7 CTMUI C2INB RP36 RF2 D-/RF3 Buffer Type 13 11 TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus  2012-2016 Microchip Technology Inc. CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD) DS30000575C-page 29 PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name COM4/SEG28/AN8/RP46/RG0 Pin Number Pin 100 80 64 Type 6 5 O O I I/O I/O Analog Analog Analog ST/DIG ST/DIG COM4 output for LCD. SEG28 output for LCD. Analog Input 8. Remappable Peripheral Pin 46 input/output. General purpose I/O pin. O O I I/O I/O Analog Analog Analog ST/DIG ST/DIG COM5 output for LCD. SEG29 output for LCD. Analog Input 19. Remappable Peripheral Pin 39 input/output. General purpose I/O pin. O O I I I/O I/O Analog Analog Analog Analog ST/DIG ST/DIG COM6 output for LCD. SEG30 output for LCD. Analog Input 18. Comparator 3 Input A. Remappable Peripheral Pin 42 input/output. General purpose I/O pin. O O I I I/O I/O Analog Analog Analog Analog ST/DIG ST/DIG COM7 output for LCD. SEG31 output for LCD. Analog Input 17. Comparator 3 Input B. Remappable Peripheral Pin 43 input/output. General purpose I/O pin. O I I I/O O I/O Analog Analog Analog ST/DIG — ST/DIG SEG26 output for LCD. Analog Input 16. Comparator 3 Input C. Remappable Peripheral Pin 44 input/output. RTCC output. General purpose I/O pin. 89 I/O ST/DIG General purpose I/O pin. 96 I/O ST/DIG General purpose I/O pin. 7 6 4 COM5 SEG29 AN19 RP39 RG1 COM6/SEG30/AN18/C3INA/RP42/ RG2 8 7 5 COM6 SEG30 AN18 C3INA RP42 RG2 COM7/SEG31/AN17/C3INB/RP43/ RG3 9 8 6 COM7 SEG31 AN17 C3INB RP43 RG3 SEG26/AN16/C3INC/RP44/RTCC/ RG4 12 SEG26 AN16 C3INC RP44 RTCC RG4 RG6 RG7 Legend: 10 8 TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus DS30000575C-page 30 Description 3 COM4 SEG28 AN8 RP46 RG0 COM5/SEG29/AN19/RP39/RG1 Buffer Type CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name A16/SEG47/AN23/RH0 Pin Number Pin 100 80 64 Type 99 1 2 27 26 25 24 SEG43 AN15 RH7 Legend: External Memory Address 17. SEG46 output for LCD. Analog Input 22. General purpose I/O pin. O O I I/O DIG Analog Analog ST/DIG External Memory Address 18. SEG45 output for LCD. Analog Input 21. General purpose I/O pin. O O I I/O DIG Analog Analog ST/DIG External Memory Address 19. SEG44 output for LCD. Analog Input 20. General purpose I/O pin. O I I I/O Analog Analog Analog ST/DIG SEG40 output for LCD. Analog Input12. Comparator 2 Input C. General purpose I/O pin. O I I I/O Analog Analog Analog ST/DIG SEG41 output for LCD. Analog Input 13. Comparator 2 Input D. General purpose I/O pin. O I I I/O Analog Analog Analog ST/DIG SEG42 output for LCD. Analog Input 14. Comparator 1 Input C. General purpose I/O pin. O I I/O Analog SEG43 output for LCD. Analog Analog Input 15. ST/DIG General purpose I/O pin. 20 SEG42 AN14 C1INC RH6 SEG43/AN15/RH7 DIG Analog Analog ST/DIG 21 SEG41 AN13 C2IND RH5 SEG42/AN14/C1INC/RH6 O O I I/O 22 SEG40 AN12 C2INC RH4 SEG41/AN13/C2IND/RH5 External Memory Address 16. SEG47 output for LCD. Analog Input 23. General purpose I/O pin. 2 A19 SEG44 AN20 RH3 SEG40/AN12/C2INC/RH4 DIG Analog Analog ST/DIG 1 A18 SEG45 AN21 RH2 A19/SEG44/AN20/RH3 O O I I/O 100 80 A17 SEG46 AN22 RH1 A18/SEG45/AN21/RH2 Description 79 A16 SEG47 AN23 RH0 A17/SEG46/AN22/RH1 Buffer Type 19 TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus  2012-2016 Microchip Technology Inc. CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD) DS30000575C-page 31 PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name ALE/SEG32/RJ0 Pin Number Pin 100 80 64 Type 77 76 75 74 49 50 51 UB SEG36 RJ7 Legend: 52 DIG External memory write low control. Analog SEG34 output for LCD. ST/DIG General purpose I/O pin. O O I/O DIG External memory write high control. Analog SEG35 output for LCD. ST/DIG General purpose I/O pin. O O I/O DIG External Memory Byte Address 0 control Analog SEG39 output for LCD. ST/DIG General purpose I/O pin. O O I/O DIG External memory chip enable control. Analog SEG38 output for LCD. ST/DIG General purpose I/O pin. O O I/O DIG External memory low byte control. Analog SEG37 output for LCD. ST/DIG General purpose I/O pin. O O I/O DIG External memory high byte control. Analog SEG36 output for LCD. ST/DIG General purpose I/O pin. 41 LB SEG37 RJ6 UB/SEG36/RJ7 O O I/O 40 CE SEG38 RJ5 LB/SEG37/RJ6 DIG External memory output enable. Analog SEG33 output for LCD. ST/DIG General purpose I/O pin. 39 BA0 SEG39 RJ4 CE/SEG38/RJ5 O O I/O 59 WRH SEG35 RJ3 BA0/SEG39/RJ4 DIG External memory address latch enable. Analog SEG32 output for LCD. ST/DIG General purpose I/O pin. 60 WRL SEG34 RJ2 WRH/SEG35/RJ3 O O I/O 61 OE SEG33 RJ1 WRL/SEG34/RJ2 42 TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus DS30000575C-page 32 Description 62 ALE SEG32 RJ0 OE/SEG33/RJ1 Buffer Type CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name SEG56/RK0 Pin Number Pin 100 80 64 Type O I/O Analog SEG59 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG60 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG61 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG62 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG63 output for LCD. ST/DIG General purpose I/O pin. 85 SEG63 RK7 Legend: Analog SEG58 output for LCD. ST/DIG General purpose I/O pin. 80 SEG62 RK6 SEG63/RK7 O I/O 71 SEG61 RK5 SEG62/RK6 Analog SEG57 output for LCD. ST/DIG General purpose I/O pin. 66 SEG60 RK4 SEG61/RK5 O I/O 63 SEG59 RK3 SEG60/RK4 Analog SEG56 output for LCD. ST/DIG General purpose I/O pin. 60 SEG58 RK2 SEG59/RK3 O I/O 55 SEG57 RK1 SEG58/RK2 Description 46 SEG56 RK0 SEG57/RK1 Buffer Type TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus  2012-2016 Microchip Technology Inc. CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD) DS30000575C-page 33 PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name SEG48/RL0 Pin Number Pin 100 80 64 Type Description 91 SEG48 RL0 SEG49/RL1 O I/O Analog SEG48 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG49 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG50 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG51 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG52 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG53 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG54 output for LCD. ST/DIG General purpose I/O pin. O I/O Analog SEG55 output for LCD. ST/DIG General purpose I/O pin. 10 SEG49 RL1 SEG50/RL2 13 SEG50 RL2 SEG51/RL3 16 SEG51 RL3 SEG52/RL4 21 SEG52 RL4 SEG53/RL5 30 SEG53 RL5 SEG54/RL6 38 SEG54 RL6 SEG55/RL7 41 SEG55 RL7 Legend: Buffer Type TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus DS30000575C-page 34 CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 1-4: PIC18FXXJ94 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number Pin 100 80 64 Type Buffer Type Description 32 26 48 38 71 57 P — Positive supply for logic and I/O pins. VDD 5 40 59 88 11 9 31 25 51 41 70 56 P — Ground reference for logic and I/O pins. VSS 14 35 39 64 87 AVDD 31 25 19 P — Positive supply for analog modules. AVSS 32 26 20 P — Ground reference for analog modules. VDDCORE/VCAP 15 12 10 P P — — Core logic power or external filter capacitor connection. External filter capacitor connection (regulator enabled/disabled). VDDCORE VCAP VBAT 29 24 18 P — VUSB3V3 28 23 17 P — Legend: TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I = Input P = Power I2C = I2C/SMBus  2012-2016 Microchip Technology Inc. USB voltage input pin. CMOS Analog O OD = CMOS compatible input or output = Analog input = Output = Open-Drain (no P diode to VDD) DS30000575C-page 35 PIC18F97J94 FAMILY • All VDD and VSS pins (see Section 2.2 “Power Supply Pins”) • All AVDD and AVSS pins, regardless of whether or not the analog device features are used (see Section 2.2 “Power Supply Pins”) • MCLR pin (see Section 2.3 “Master Clear (MCLR) Pin”) R1 R2 Additionally, the following pins may be required: • VREF+/VREF- pins are used when external voltage reference for analog modules is implemented Note: The AVDD and AVSS pins must always be connected, regardless of whether any of the analog modules are being used. (1) MCLR VCAP/VDDCORE C1 C7 PIC18FXXJXX C6(2) VSS VDD VDD VSS C3(2) C5(2) These pins must also be connected if they are being used in the end application: • PGC/PGD pins used for In-Circuit Serial Programming™ (ICSP™) and debugging purposes (see Section 2.5 “ICSP Pins”) • OSC1 and OSC2 pins when an external oscillator source is used (see Section 2.6 “External Oscillator Pins”) VSS VDD VSS The following pins must always be connected: C2(2) VDD Getting started with the PIC18FXXJ94 of 8-bit microcontrollers requires attention to a minimal set of device pin connection before proceeding with development. RECOMMENDED MINIMUM CONNECTIONS VDD Basic Connection Requirements FIGURE 2-1: AVSS 2.1 GUIDELINES FOR GETTING STARTED WITH PIC18FJ MICROCONTROLLERS AVDD 2.0 C4(2) Key (all values are recommendations): C1 through C6: 0.1 F, 20V ceramic C7: 10 F, 6.3V or greater, tantalum or ceramic R1: 10 kΩ R2: 100Ω to 470Ω Note 1: 2: See Section 2.4 “Core Voltage Regulator (VCAP/VDDCORE)” for explanation of VCAP/ VDDCORE connections. The example shown is for a PIC18F device with five VDD/VSS and AVDD/AVSS pairs. Other devices may have more or less pairs; adjust the number of decoupling capacitors appropriately. The minimum mandatory connections are shown in Figure 2-1. DS30000575C-page 36  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 2.2 2.2.1 Power Supply Pins DECOUPLING CAPACITORS The use of decoupling capacitors on every pair of power supply pins, such as VDD, VSS, AVDD and AVSS, is required. Consider the following criteria when using decoupling capacitors: • Value and type of capacitor: A 0.1 F (100 nF), 10-20V capacitor is recommended. The capacitor should be a low-ESR device, with a resonance frequency in the range of 200 MHz and higher. Ceramic capacitors are recommended. • Placement on the printed circuit board: The decoupling capacitors should be placed as close to the pins as possible. It is recommended to place the capacitors on the same side of the board as the device. If space is constricted, the capacitor can be placed on another layer on the PCB using a via; however, ensure that the trace length from the pin to the capacitor is no greater than 0.25 inch (6 mm). • Handling high-frequency noise: If the board is experiencing high-frequency noise (upward of tens of MHz), add a second ceramic type capacitor in parallel to the above described decoupling capacitor. The value of the second capacitor can be in the range of 0.01 F to 0.001 F. Place this second capacitor next to each primary decoupling capacitor. In high-speed circuit designs, consider implementing a decade pair of capacitances as close to the power and ground pins as possible (e.g., 0.1 F in parallel with 0.001 F). • Maximizing performance: On the board layout from the power supply circuit, run the power and return traces to the decoupling capacitors first, and then to the device pins. This ensures that the decoupling capacitors are first in the power chain. Equally important is to keep the trace length between the capacitor and the power pins to a minimum, thereby reducing PCB trace inductance. 2.2.2 TANK CAPACITORS On boards with power traces running longer than six inches in length, it is suggested to use a tank capacitor for integrated circuits, including microcontrollers, to supply a local power source. The value of the tank capacitor should be determined based on the trace resistance that connects the power supply source to the device, and the maximum current drawn by the device in the application. In other words, select the tank capacitor so that it meets the acceptable voltage sag at the device. Typical values range from 4.7 F to 47 F.  2012-2016 Microchip Technology Inc. 2.3 Master Clear (MCLR) Pin The MCLR pin provides two specific device functions: Device Reset, and Device Programming and Debugging. If programming and debugging are not required in the end application, a direct connection to VDD may be all that is required. The addition of other components, to help increase the application’s resistance to spurious Resets from voltage sags, may be beneficial. A typical configuration is shown in Figure 2-1. Other circuit designs may be implemented, depending on the application’s requirements. During programming and debugging, the resistance and capacitance that can be added to the pin must be considered. Device programmers and debuggers drive the MCLR pin. Consequently, specific voltage levels (VIH and VIL) and fast signal transitions must not be adversely affected. Therefore, specific values of R1 and C1 will need to be adjusted based on the application and PCB requirements. For example, it is recommended that the capacitor, C1, be isolated from the MCLR pin during programming and debugging operations by using a jumper (Figure 2-2). The jumper is replaced for normal run-time operations. Any components associated with the MCLR pin should be placed within 0.25 inch (6 mm) of the pin. FIGURE 2-2: EXAMPLE OF MCLR PIN CONNECTIONS VDD R1 R2 JP MCLR PIC18FXXJXX C1 Note 1: R1  10 k is recommended. A suggested starting value is 10 k. Ensure that the MCLR pin VIH and VIL specifications are met. 2: R2  470 will limit any current flowing into MCLR from the external capacitor, C, in the event of MCLR pin breakdown, due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). Ensure that the MCLR pin VIH and VIL specifications are met. DS30000575C-page 37 PIC18F97J94 FAMILY 2.4 Core Voltage Regulator (VCAP/ VDDCORE) FIGURE 2-3: A low-ESR (< 5Ω) capacitor is required on the VCAP pin to stabilize the output voltage of the on-chip voltage regulator. The VCAP pin must not be connected to VDD and must use a capacitor of 10 μF connected to ground. The type can be ceramic or tantalum. Suitable examples of capacitors are shown in Table 2-1. Capacitors with equivalent specification can be used. FREQUENCY vs. ESR PERFORMANCE FOR SUGGESTED VCAP 10 ESR () 1 Designers may use Figure 2-3 to evaluate ESR equivalence of candidate devices. 0.1 0.01 It is recommended that the trace length not exceed 0.25 inch (6 mm). Refer to Section 30.0 “Electrical Specifications” for additional information. 0.001 0.01 Note: 0.1 1 10 100 Frequency (MHz) 1000 10,000 Typical data measurement at 25°C, 0V DC bias. . TABLE 2-1: SUITABLE CAPACITOR EQUIVALENTS Make Part # Nominal Capacitance Base Tolerance Rated Voltage Temp. Range TDK C3216X7R1C106K 10 µF ±10% 16V -55 to 125ºC TDK C3216X5R1C106K 10 µF ±10% 16V -55 to 85ºC Panasonic ECJ-3YX1C106K 10 µF ±10% 16V -55 to 125ºC Panasonic ECJ-4YB1C106K 10 µF ±10% 16V -55 to 85ºC Murata GRM32DR71C106KA01L 10 µF ±10% 16V -55 to 125ºC Murata GRM31CR61C106KC31L 10 µF ±10% 16V -55 to 85ºC DS30000575C-page 38  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY CONSIDERATIONS FOR CERAMIC CAPACITORS In recent years, large value, low-voltage, surface-mount ceramic capacitors have become very cost effective in sizes up to a few tens of microfarad. The low-ESR, small physical size and other properties make ceramic capacitors very attractive in many types of applications. Ceramic capacitors are suitable for use with the VDDCORE voltage regulator of this microcontroller. However, some care is needed in selecting the capacitor to ensure that it maintains sufficient capacitance over the intended operating range of the application. Typical low-cost, 10 µF ceramic capacitors are available in X5R, X7R and Y5V dielectric ratings (other types are also available, but are less common). The initial tolerance specifications for these types of capacitors are often specified as ±10% to ±20% (X5R and X7R), or 20%/+80% (Y5V). However, the effective capacitance that these capacitors provide in an application circuit will also vary based on additional factors, such as the applied DC bias voltage and the temperature. The total in-circuit tolerance is, therefore, much wider than the initial tolerance specification. The X5R and X7R capacitors typically exhibit satisfactory temperature stability (ex: ±15% over a wide temperature range, but consult the manufacturer’s data sheets for exact specifications). However, Y5V capacitors typically have extreme temperature tolerance specifications of +22%/-82%. Due to the extreme temperature tolerance, a 10 µF nominal rated Y5V type capacitor may not deliver enough total capacitance to meet minimum VDDCORE voltage regulator stability and transient response requirements. Therefore, Y5V capacitors are not recommended for use with the VDDCORE regulator if the application must operate over a wide temperature range. In addition to temperature tolerance, the effective capacitance of large value ceramic capacitors can vary substantially, based on the amount of DC voltage applied to the capacitor. This effect can be very significant, but is often overlooked or is not always documented. A typical DC bias voltage vs. capacitance graph for X7R type and Y5V type capacitors is shown in Figure 2-4. FIGURE 2-4: Capacitance Change (%) 2.4.1 DC BIAS VOLTAGE vs. CAPACITANCE CHARACTERISTICS 10 0 -10 16V Capacitor -20 -30 -40 10V Capacitor -50 -60 -70 6.3V Capacitor -80 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 DC Bias Voltage (VDC) When selecting a ceramic capacitor to be used with the VDDCORE voltage regulator, it is suggested to select a high-voltage rating, so that the operating voltage is a small percentage of the maximum rated capacitor voltage. For example, choose a ceramic capacitor rated at 16V for the 2.5V VDDCORE voltage. Suggested capacitors are shown in Table 2-1. 2.5 ICSP Pins The PGC and PGD pins are used for In-Circuit Serial Programming™ (ICSP™) and debugging purposes. It is recommended to keep the trace length between the ICSP connector and the ICSP pins on the device as short as possible. If the ICSP connector is expected to experience an ESD event, a series resistor is recommended, with the value in the range of a few tens of ohms, not to exceed 100Ω. Pull-up resistors, series diodes, and capacitors on the PGC and PGD pins are not recommended as they will interfere with the programmer/debugger communications to the device. If such discrete components are an application requirement, they should be removed from the circuit during programming and debugging. Alternatively, refer to the AC/DC characteristics and timing requirements information in the respective device Flash programming specification for information on capacitive loading limits, and pin input voltage high (VIH) and input low (VIL) requirements. For device emulation, ensure that the “Communication Channel Select” (i.e., PGCx/PGDx pins), programmed into the device, matches the physical connections for the ICSP to the Microchip debugger/emulator tool. For more information on available Microchip development tools connection requirements, refer to Section 31.0 “Development Support”.  2012-2016 Microchip Technology Inc. DS30000575C-page 39 PIC18F97J94 FAMILY 2.6 External Oscillator Pins FIGURE 2-5: Many microcontrollers have options for at least two oscillators: a high-frequency primary oscillator and a low-frequency secondary oscillator (refer to Section 3.0 “Oscillator Configurations” for details). The oscillator circuit should be placed on the same side of the board as the device. Place the oscillator circuit close to the respective oscillator pins with no more than 0.5 inch (12 mm) between the circuit components and the pins. The load capacitors should be placed next to the oscillator itself, on the same side of the board. Use a grounded copper pour around the oscillator circuit to isolate it from surrounding circuits. The grounded copper pour should be routed directly to the MCU ground. Do not run any signal traces or power traces inside the ground pour. Also, if using a two-sided board, avoid any traces on the other side of the board where the crystal is placed. Single-Sided and In-Line Layouts: Copper Pour (tied to ground) For additional information and design guidance on oscillator circuits, refer to these Microchip Application Notes, available at the corporate website (www.microchip.com): • AN826, “Crystal Oscillator Basics and Crystal Selection for rfPIC™ and PICmicro® Devices” • AN849, “Basic PICmicro® Oscillator Design” • AN943, “Practical PICmicro® Oscillator Analysis and Design” • AN949, “Making Your Oscillator Work” 2.7 Unused I/Os Primary Oscillator Crystal DEVICE PINS Primary Oscillator OSC1 C1 ` OSC2 GND C2 ` T1OSO T1OS I Timer1 Oscillator Crystal Layout suggestions are shown in Figure 2-5. In-line packages may be handled with a single-sided layout that completely encompasses the oscillator pins. With fine-pitch packages, it is not always possible to completely surround the pins and components. A suitable solution is to tie the broken guard sections to a mirrored ground layer. In all cases, the guard trace(s) must be returned to ground. In planning the application’s routing and I/O assignments, ensure that adjacent port pins, and other signals in close proximity to the oscillator, are benign (i.e., free of high frequencies, short rise and fall times, and other similar noise). SUGGESTED PLACEMENT OF THE OSCILLATOR CIRCUIT ` T1 Oscillator: C1 T1 Oscillator: C2 Fine-Pitch (Dual-Sided) Layouts: Top Layer Copper Pour (tied to ground) Bottom Layer Copper Pour (tied to ground) OSC2 C2 Oscillator Crystal GND C1 OSC1 DEVICE PINS Unused I/O pins should be configured as outputs and driven to a logic low state. Alternatively, connect a 1 kΩ to 10 kΩ resistor to VSS on unused pins and drive the output to logic low. DS30000575C-page 40  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 3.0 OSCILLATOR CONFIGURATIONS • Software-controllable switching between various clock sources • Software-controllable postscaler for selective clocking of CPU for system power savings • A Fail-Safe Clock Monitor (FSCM) that detects clock failure and permits safe application recovery or shutdown • A separate and independently configurable system clock output for synchronizing external hardware This section describes the PIC18F oscillator system and its operation. The PIC18F oscillator system has the following modules and features: • A total of four external and internal oscillator options as clock sources, providing up to 11 different clock modes • An on-chip USB PLL block to provide a stable 48 MHz clock for the USB module, as well as a range of frequency options for the system clock FIGURE 3-1: A simplified diagram of the oscillator system is shown in Figure 3-1. PIC18F GENERAL SYSTEM CLOCK DIAGRAM PIC18F97J94 Family 48 MHz USB Clock Primary Oscillator MS, HS, EC OSC2 REFOxCON2 USB PLL MSPLL, HSPLL, ECPLL, FRCPLL PLL & DIV OSC1 Reference Clock Generator 8 MHz 8 MHz (nominal) FRC Oscillator Reference from USB D+/D- PLLDIV FRC Active Clock Tuning Control FRCDIV Peripherals OSCCON3 FRCDIV 16 LPRC Oscillator 31 kHz (nominal) REFO CPDIV Postscaler 4 MHz FRC 500 kHz LPRC Secondary Oscillator SOSC SOSCO SOSCI SOSCEN Enable Oscillator Clock Control Logic Fail-Safe Clock Monitor WDT, PWRT Clock Source Option for Other Modules  2012-2016 Microchip Technology Inc. DS30000575C-page 41 PIC18F97J94 FAMILY 3.1 CPU Clocking Scheme The system clock source can be provided by one of four sources: • Primary Oscillator (POSC) on the OSC1 and OSC2 pins • Secondary Oscillator (SOSC) on the SOSCI and SOSCO pins • Fast Internal RC (FRC) Oscillator • Low-Power Internal RC (LPRC) Oscillator FIGURE 3-2: The Primary Oscillator and FRC sources have the option of using the internal USB PLL block, which generates both the USB module clock and a separate system clock from the 96 MHz PLL. Refer to Section 3.8.1 “Oscillator Modes and USB Operation” for additional information. The internal FRC provides an 8 MHz clock source. It can optionally be reduced by the programmable clock divider to provide a range of system clock frequencies. The selected clock source generates the processor and peripheral clock sources. The processor clock source is divided by four to produce the internal instruction cycle clock, FCY. In this document, the instruction cycle clock is also denoted by FOSC/4. The internal instruction cycle clock, FOSC/4, can be provided on the OSC2 I/O pin for some operating modes of the Primary Oscillator. The timing diagram in Figure 3-2 shows the relationship between the processor clock source and instruction execution. CLOCK OR INSTRUCTION CYCLE TIMING TCY FOSC FCY PC PC Fetch INST (PC) Execute INST (PC – 2) DS30000575C-page 42 PC + 2 Fetch INST (PC + 2) Execute INST (PC) PC + 4 Fetch INST (PC + 4) Execute INST (PC + 2)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 3.2 Oscillator Configuration The oscillator source (and operating mode) that is used at a device Power-on Reset (POR) event is selected using Configuration bit settings. The Oscillator Configuration bit settings are in the Configuration registers located in the program memory (refer to Section 28.1 “Configuration Bits” for more information). The Primary Oscillator Configuration bits, POSCMD (CONFIG3L), and Oscillator Configuration bits, TABLE 3-1: FOSC (CONFIG2L), select the oscillator source that is used at a POR. The FRC Oscillator with Postscaler (FRCDIV) is the default (unprogrammed) selection. The Secondary Oscillator, or one of the internal oscillators, may be chosen by programming these bit locations. The Configuration bits allow users to choose between 11 different clock modes, as shown in Table 3-1. CONFIGURATION BIT VALUES FOR CLOCK SELECTION Oscillator Mode Oscillator Source POSCMD FOSC Fast RC Oscillator with Postscaler (FRCDIV) Internal 11 111 1, 2 Fast RC Oscillator divided by 16 (FRC500kHz) Internal 11 110 1 Low-Power RC Oscillator (LPRC) Notes Internal 11 101 1 Secondary 11 100 1 Primary Oscillator (HS) with PLL Module (HSPLL) Primary 10 011 Primary Oscillator (MS) with PLL Module (MSPLL) Primary 01 011 Primary Oscillator (EC) with PLL Module (ECPLL) Primary 00 011 Primary Oscillator (HS) Primary 10 010 Primary Oscillator (MS) Primary 01 010 Primary Oscillator (EC) Primary 00 010 Fast RC Oscillator with PLL Module (FRCPLL) Internal 11 001 1 Fast RC Oscillator (FRC) Internal 11 000 1 Secondary (Timer1) Oscillator (SOSC) Note 1: 2: OSC2 pin function is determined by the CLKOEN Configuration bit. Default oscillator mode for an unprogrammed (erased) device.  2012-2016 Microchip Technology Inc. DS30000575C-page 43 PIC18F97J94 FAMILY 3.2.1 CLOCK SWITCHING MODE CONFIGURATION BITS The FSCMx Configuration bits (CONFIG3L) are used to jointly configure device clock switching and the Fail-Safe Clock Monitor (FSCM). Clock switching is enabled only when FSCM1 is programmed (‘0’). The FSCM is enabled only when FSCM are both programmed (‘00’). 3.2.2 OSC1 AND OSC2 PIN FUNCTIONS IN NON-CRYSTAL MODES When the Primary Oscillator on OSC1 and OSC2 is not configured as the clock source (POSCMD = 11), the OSC1 pin is automatically reconfigured as a digital I/O. In this configuration, as well as when the Primary Oscillator is configured for EC mode (POSCMD = 00), the OSC2 pin can also be configured as a digital I/O by programming the CLKOEN Configuration bit (CONFIG2L). When CLKOEN is unprogrammed (‘1’), a FOSC/4 clock output is available on OSC2 for testing or synchronization purposes. With CLKOEN programmed (‘0’), the OSC2 pin becomes a general purpose I/O pin. In both of these configurations, the feedback device between OSC1 and OSC2 is turned off to save current. 3.3 Control Registers The operation of the oscillator is controlled by six Special Function Registers (SFRs): • • • • • • OSCCON OSCCON2 OSCCON3 OSCCON4 ACTCON OSCTUNE 3.3.1 OSCILLATOR CONTROL REGISTER (OSCCON) The OSCCON register (Register 3-1) is the main control register for the oscillator. It controls clock source switching and allows the monitoring of clock sources. The COSCx (OSCCON) Status bits are read-only bits that indicate the current oscillator source the device is operating from. The COSCx bits default to the Internal Fast RC Oscillator with Postscaler (FRCDIV), configured for 4 MHz, on a Power-on Reset (POR) and DS30000575C-page 44 Master Clear Reset (MCLR). A clock switch will automatically be performed to the new oscillator source selected by the FOSCx Configuration bits (CONFIG2L). The COSCx bits will change to indicate the new oscillator source at the end of a clock switch operation. The NOSCx Status bits select the clock source for the next clock switch operation. On POR and MCLRs, these bits automatically select the oscillator source defined by the FOSCx Configuration bits. These bits can be modified by software. Setting the CLKLOCK bit (OSCCON2) prevents clock switching if the FSCM1 Configuration bit is set. If the FSCM1 bit is clear, the CLKLOCK bit state is ignored and clock switching can occur. The IOLOCK bit (OSCCON2) is used to unlock the Peripheral Pin Select (PPS) feature; it has no function in the system clock’s operation. The LOCK Status bit (OSCCON2) is read-only and indicates the status of the PLL circuit. It is set when the PLL achieves a frequency lock and is reset when a valid clock switching sequence is initiated. It reads as ‘0’ whenever the PLL is not used as part of the current clock source. The CF Status bit (OSCCON2) is a readable/clearable Status bit that indicates a clock failure; it is reset whenever a valid clock switch occurs. The POSCEN bit (OSCCON2) is used to control the operation of the Primary Oscillator in Sleep mode. Setting this bit bypasses the normal automatic shutdown of the oscillator whenever Sleep mode is invoked. The Secondary Oscillator can be turned on by a variety of options: • • • • • • SOSCGO – OSCCON2 SOSCSEL – CONFIG2L FOSC – CONFIG2L DSWDTOSC – CONFIG8H RTCEN – RTCCON1 SOSCEN – T1CON, T3CON or T5CON The ACTCON register (Register 3-10) controls the Active Clock Tuning features.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 3-1: OSCCON: OSCILLATOR CONTROL REGISTER R/W-0 R-x R-x R-x U-0 R/W-x R/W-x R/W-x IDLEN COSC2 COSC1 COSC0 — NOSC2 NOSC1 NOSC0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 IDLEN: Idle Enable bit 1 = SLEEP instruction invokes Idle mode 0 = SLEEP instruction invokes Sleep mode bit 6-4 COSC: Current Oscillator Selection bits (read-only) 000 = Fast RC Oscillator (FRC) 001 = Fast RC Oscillator (FRC), divided by N, with PLL module 010 = Primary Oscillator (MS, HS, EC) 011 = Primary Oscillator (MS, HS, EC) with PLL module 100 = Secondary Oscillator (SOSC) 101 = Low-Power RC Oscillator (LPRC) 110 = Fast RC Oscillator (FRC) divided by 16 (500 kHz) 111 = Fast RC Oscillator (FRC) divided by N bit 3 Unimplemented: Read as ‘0’ bit 2-0 NOSC: New Oscillator Selection bits 000 = Fast RC Oscillator (FRC) 001 = Fast RC Oscillator (FRC), divided by N, with PLL module 010 = Primary Oscillator (MS, HS, EC) 011 = Primary Oscillator (MS, HS, EC) with PLL module 100 = Secondary Oscillator (SOSC) 101 = Low-Power RC Oscillator (LPRC) 110 = Fast RC Oscillator (FRC) divided by 16 (500 kHz) 111 = Fast RC Oscillator (FRC) divided by N  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 45 PIC18F97J94 FAMILY REGISTER 3-2: OSCCON2: OSCILLATOR CONTROL REGISTER 2 R/W-0 R/W-0 R-0 U-0 R/C-0 R/W-0 R/W-0 U-0 CLKLOCK(2) IOLOCK(1) LOCK — CF POSCEN SOSCGO — bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 CLKLOCK: Clock Lock Enabled bit(2) 1 = Clock and PLL selection are locked and may not be modified 0 = Clock and PLL selection are not locked, configurations may be modified bit 6 IOLOCK: I/O Lock Enable bit(1) 1 = I/O lock is active (If IOL1WAY (CONFIG5H = 1), the bit cannot be cleared, once it is set, except on a device Reset.) 0 = I/O lock is not active bit 5 LOCK: PLL Lock Status bit (read-only) 1 = Indicates that PLL module is in lock or PLL start-up timer is satisfied 0 = Indicates that PLL module is out of lock, PLL start-up timer is in progress or PLL is disabled bit 4 Unimplemented: Read as ‘0’ bit 3 CF: Clock Fail Detect bit (readable/clearable by application) 1 = FSCM has detected a clock failure 0 = FSCM has not detected A clock failure bit 2 POSCEN: Primary Oscillator (POSC) Enable bit 1 = Enables Primary Oscillator in Sleep mode 0 = Disables Primary Oscillator in Sleep mode bit 1 SOSCGO: 32 kHz Secondary (LP) Oscillator Enable bit 1 = Enables Secondary Oscillator independent of other SOSC enable requests; provides a way to keep the SOSC running even when not actively used by the system 0 = Disables Secondary Oscillator; the SOSC will be enabled if directly requested by the system. Reset on POR or BOR only. bit 0 Unimplemented: Read as ‘0’ Note 1: 2: The IOLOCK bit cannot be cleared once it has been set, provided that the IOL1WAY (CONFIG5H) = 1. If the user wants to change the clock source, ensure that the FSCM bits (CONFIG3L) are set appropriately. DS30000575C-page 46  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 3.3.2 OSCCON3 – CLOCK DIVIDER REGISTER (IRCF BITS) This option is described in more detail in Section 3.10.2 “FRC Postscaler Mode (FRCDIV)” and Section 3.10.3 “FRC Oscillator with PLL Mode (FRCPLL)”. The IRCFx bits (OSCCON3) select the postscaler option for the FRC Oscillator output, allowing users to choose a lower clock frequency than the nominal 8 MHz. REGISTER 3-3: U-0 OSCCON3: OSCILLATOR CONTROL REGISTER 3 U-0 — — U-0 — U-0 U-0 — R/W-0 (1) — IRCF2 R/W-0 R/W-1 (1) IRCF1 IRCF0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-3 Unimplemented: Read as ‘0’ bit 2-0 IRCF: Reference Clock Divider bits(1) 000 = FRC divide-by-1 001 = FRC divide-by-2 (default) 010 = FRC divide-by-4 011 = FRC divide-by-8 100 = FRC divide-by-16 101 = FRC divide-by-32 110 = FRC divide-by-64 111 = FRC divide-by-256 Note 1: x = Bit is unknown The default FRC divide-by setting on an 8-bit device corresponds to 1 MIPS operation. REGISTER 3-4: OSCCON4: OSCILLATOR CONTROL REGISTER 4 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 CPDIV1 CPDIV0 PLLEN — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 CPDIV: USB System Clock Select bits (postscaler select from 64 MHz clock branch) 00 = Input clock/1 01 = Input clock/2 10 = Input clock/4 11 = Input clock/8 bit 5 PLLEN: PLL Enable bit 1 = PLL is enabled even though it is not requested by the CPU; provides ability to “warm-up” the PLL and keep it running to avoid the PLL start-up time. This setting will force the PLL and associated clock source to stay active in Sleep. 0 = PLL is disabled; PLL will be automatically turned on when SRC1 is selected, or when REFO1 or REFO2 is enabled and using the PLL clock as its source. In either case, the PLL will require a start-up time. bit 4-0 Unimplemented: Read as ‘0’  2012-2016 Microchip Technology Inc. DS30000575C-page 47 PIC18F97J94 FAMILY 3.3.3 OSCILLATOR TUNING REGISTER (OSCTUNE) The FRC Oscillator Tuning register (Register 3-5) allows the user to fine-tune the FRC Oscillator. Refer to the data sheet of the specific device for further information regarding the FRC Oscillator tuning. REGISTER 3-5: The tuning response of the FRC Oscillator may not be monotonic or linear; the next closest frequency may be offset by a number of steps. It is recommended that users try multiple values of OSCTUNE to find the closest value to the desired frequency. OSCTUNE: FRC OSCILLATOR TUNING REGISTER U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — TUN5 TUN4 TUN3 TUN2 TUN1 TUN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at all Resets ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 TUN: FRC Oscillator Tuning bits 011111 = Maximum frequency deviation 011110 = . . . 000001 = 000000 = Center frequency; oscillator is running at factory calibrated frequency 111111 = . . . 100001 = 100000 = Minimum frequency deviation DS30000575C-page 48  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 3.4 Reference Clock Output Control Module The PIC18F97J94 family has two Reference Clock Output (REFO) modules. Each of the Reference Clock Output modules provides the user with the ability to send out a programmed output clock onto the REFO1or REFO2 pins. 3.4.1 REFERENCE CLOCK SOURCE 3.4.3 OPERATION IN SLEEP MODE If any clock source, other than the peripheral clock, is used as a base reference (i.e., ROSEL  0001), the user has the option to configure the behavior of the oscillator in Sleep mode. The RSLP Configuration bit determines if the oscillator will continue to run in Sleep. If RSLP = 0, the oscillator will be shut down in Sleep (assuming no other consumers are requesting it). If RSLP = 1, the oscillator will continue to run in Sleep. The module provides the ability to select one of the following clock sources: The Reference Clock Output is synchronized with the Sleep signal to avoid any glitches on its output. • • • • 3.4.3.1 Primary Crystal Oscillator (POSC) Secondary Crystal Oscillator (SOSC) 32.768 kHz Internal Oscillator (INTOSC) Fast Internal Oscillator (FRC) It includes a programmable clock divider with ratios ranging from 1:1 to 1:65534. When the clock source is a crystal or internal oscillator, the RSLP bit can be set to continue REFO operation while the device is in Sleep Mode. 3.4.2 CLOCK SYNCHRONIZATION The Reference Clock Output is enabled only once (ON = 1). Note that the source of the clock and the divider values should be chosen prior to the bit being set to avoid glitches on the REFO output. Once the ON bit is set, its value is synchronized to the Reference Clock Output domain to enable the output. This ensures that no glitches will be seen on the output. Similarly, when the ON bit is cleared, the output and the associated output enable signals will be synchronized and disabled on the falling edge of the Reference Clock Output. Note that with large divider values, this will cause the REFO to be enabled for some period after ON is cleared.  2012-2016 Microchip Technology Inc. Module Enable Signal The REFOx module may be enabled or disabled using the REFOxMD register bit, which holds the REFOx module in Reset, or the ON register bit, which does not. 3.4.3.2 Registers and Bits This module provides the following device registers and/or bits: • REFOxCON – Reference Clock Output Control Register • REFOxCON1 – Reference Clock Output Control 1 Register • REFOxCON2 – Reference Clock Output Control 2 Register • REFOxCON3 – Reference Clock Output Control 3 Register In addition, the REFOxCON1 module needs to be enabled by clearing the REFOxMD disable bit (PMD3). 3.4.3.3 Interrupts This module does not generate any interrupts. Note: Throughout this section, references to register and bit names that may be associated with specific Reference Clock Output modules are referred to generically by the use of ‘x’ in place of the specific module number. Thus, “REFOxCON” might refer to the control register for either REFO1 or REFO2. DS30000575C-page 49 PIC18F97J94 FAMILY REGISTER 3-6: R/W-0 REFOxCON: REFERENCE CLOCK OUTPUT CONTROL REGISTER U-0 ON — R/W-0 SIDL R/W-0 OE R/W-0 (1) RSLP U-0 HC/R/W-0 HS/HC/R-0 — DIVSW_EN ACTIVE bit 7 bit 0 Legend: HC = Hardware Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at all Resets ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 ON: Reference Clock Output Enable bit 1 = Reference clock module is enabled 0 = Reference clock module is disabled bit 6 Unimplemented: Read as ‘0’ bit 5 SIDL: Peripheral Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 4 OE: Reference Clock Output Enable bit 1 = Reference clock is driven out on REFOx pin 0 = Reference clock is NOT driven out on REFOx pin bit 3 RSLP: Reference Clock Output Run in Sleep bit(1) 1 = Reference Clock Output continues to run in Sleep 0 = Reference Clock Output is disabled in Sleep bit 2 Unimplemented: Read as ‘0’ bit 1 DIVSW_EN: Clock RODIV Switch Enabled Status bit 1 = Clock Divider Switching currently in progress 0 = Clock Divider Switching has completed bit 0 ACTIVE: Reference Clock Output Request Status bit 1 = Reference clock request is active (user should not update the ROSEL and RODIV register fields) 0 = Reference clock request is not active (user may update the ROSEL and RODIV register fields) Note 1: This bit has no effect when ROSEL = 0000/0001, as the system clock and peripheral clock are always disabled in Sleep mode on PIC18 devices. DS30000575C-page 50  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 3-7: REFOxCON1: REFERENCE CLOCK OUTPUT CONTROL REGISTER 1 U-0 U-0 U-0 U-0 R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) — — — — ROSEL3 ROSEL2 ROSEL1 ROSEL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at all Resets ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-4 Unimplemented: Read as ‘0’ (Reserved for additional ROSEL bits.) bit 3-0 ROSEL: Reference Clock Output Source Select bits(1) Select one of the various clock sources to be used as the reference clock. 0111-1111 = Reserved 0110 = PLL (4/6/8x or 96 MHz) 0101 = SOSC 0100 = LPRC 0011 = FRC 0010 = POSC 0001 = Peripheral clock (reference clock reflects any peripheral clock switching) 0000 = System clock (reference clock reflects any device clock switching) When PLLDIV (CONFIG2H) = 1111, ROSEL should not be set to ‘0110’. Note 1: The ROSEL register field should not be written while the ACTIVE (REFOxCON) bit is ‘1’; undefined behavior will result.  2012-2016 Microchip Technology Inc. DS30000575C-page 51 PIC18F97J94 FAMILY REGISTER 3-8: REFOxCON2: REFERENCE CLOCK OUTPUT CONTROL REGISTER 2 R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) R/W -0(1) R/W -0(1) RODIV7 RODIV6 RODIV5 RODIV4 RODIV3 RODIV2 RODIV1 RODIV0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at all Resets ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 Note 1: x = Bit is unknown RODIV: Reference Clock Output Divider bits(1) Reserved for expansion of RODIV. The RODIV register field should not be written while the ACTIVE (REFOxCON) bit is ‘1’; Undefined behavior will result. REGISTER 3-9: REFOxCON3: REFERENCE CLOCK OUTPUT CONTROL REGISTER 3 U-0 R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) — RODIV14 RODIV13 RODIV12 RODIV11 RODIV10 RODIV9 RODIV8 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at all Resets ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 Unimplemented: Read as ‘0’ bit 6-0 RODIV: Reference Clock Output Divider bits(1) Used in conjunction with RODIV to specify clock divider frequency. 111111111111111 = REFO clock is base clock frequency divided by 65,534 (32,767 * 2) 111111111111110 = REFO clock is base clock frequency divided by 65,532 (32,766 * 2) • • • 000000000000011 = REFO clock is base clock frequency divided by 6 (3 * 2) 000000000000010 = REFO clock is base clock frequency divided by 4 (2 * 2) 000000000000001 = REFO clock is base clock frequency divided by 2 (1 * 2) 000000000000000 = REFO clock is the same frequency as the base clock (no divider) Note 1: The RODIV register field should not be written while the ACTIVE (REFOxCON) bit is ‘1’; undefined behavior will result. DS30000575C-page 52  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 3.5 Primary Oscillator (POSC) input or an external crystal. Further details of the Primary Oscillator operating modes are described in subsequent sections. The Primary Oscillator has up to 6 operating modes, summarized in Table 3-2. The Primary Oscillator is available on the OSC1 and OSC2 pins of the PIC18F family. In general, the Primary Oscillator can be configured for an external clock TABLE 3-2: PRIMARY OSCILLATOR OPERATING MODES Oscillator Mode EC Description OSC2 Pin Function External clock input (0-64 MHz) FOSC/4 ECPLL External clock input (4-48 MHz), PLL enabled FOSC/4, Note 2 HS 10 MHz-32 MHz crystal Note 1 HSPLL 10 MHz-32 MHz crystal, PLL enabled Note 2 MS 3.5 MHz-10 MHz crystal Note 1 MSPLL 3.5 MHz-8 MHz crystal, PLL enabled Note 1 Note 1: External crystal is connected to OSC1 and OSC2 in these modes. 2: Available only in devices with special PLL blocks (such as the 96 MHz PLL); the basic 4x PLL block generates clock frequencies beyond the device’s operating range. The POSCMDx and FOSCx Configuration bits (CONFIG3L and CONFIG2L, respectively) select the operating mode of the Primary Oscillator. The POSCMD bits select the particular submode to be used (MS, HS or EC), while the FOSC bits determine if the oscillator will be used by itself or with FIGURE 3-3: the internal PLL. The PIC18F operates from the Primary Oscillator whenever the COSCx bits (OSCCON) are set to ‘010’ or ‘011’. Refer to the “Electrical Characteristics” section in the specific device data sheet for further information regarding frequency range for each crystal mode. CRYSTAL OR CERAMIC RESONATOR OPERATION (MS OR HS OSCILLATOR MODE) To Internal Logic OSC1 C1(3) XTAL RF(2) Sleep OSC2 RS(1) C2 (3) PIC18F Note 1: A series resistor, Rs, may be required for AT strip cut crystals. 2: The internal feedback resistor, RF, is typically in the range of 2 to 10 M 3: See Section 3.6.5 “Determining the Best Values for Oscillator Components”.  2012-2016 Microchip Technology Inc. DS30000575C-page 53 PIC18F97J94 FAMILY 3.5.1 3.6 SELECTING A PRIMARY OSCILLATOR MODE Crystal Oscillators and Ceramic Resonators The main difference between the MS and HS modes is the gain of the internal inverter of the oscillator circuit, which allows the different frequency ranges. The MS mode is a medium power, medium frequency mode. HS mode provides the highest oscillator frequencies with a crystal. OSC2 provides crystal feedback in both HS and MS Oscillator modes. In MS and HS modes, a crystal or ceramic resonator is connected to the OSC1 and OSC2 pins to establish oscillation (Figure 3-3). The PIC18F oscillator design requires the use of a parallel cut crystal. Using a series cut crystal may give a frequency out of the crystal manufacturer’s specifications. The EC and HS modes that use the PLL circuit provide the highest device operating frequencies. The oscillator circuit will consume the most current in these modes because the PLL is enabled to multiply the frequency of the oscillator. 3.6.1 In general, users should select the oscillator option with the lowest possible gain that still meets their specifications. This will result in lower dynamic currents (IDD). The frequency range of each oscillator mode is the recommended frequency cutoff, but the selection of a different gain mode is acceptable as long as a thorough validation is performed (voltage, temperature and component variations, such as resistor, capacitor and internal oscillator circuitry). The oscillator feedback circuit is disabled in all EC modes. The OSC1 pin is a high-impedance input and can be driven by a CMOS driver. If the Primary Oscillator is configured for an external clock input, the OSC2 pin is not required to support the oscillator function. For these modes, the OSC2 pin can be used as an additional device I/O pin or a clock output pin. When the OSC2 pin is used as a clock output pin, the output frequency is FOSC/4. FIGURE 3-4: OSCILLATOR/RESONATOR STARTUP As the device voltage increases from VSS, the oscillator will start its oscillations. The time required for the oscillator to start oscillating depends on many factors, including: • • • • • • Crystal/resonator frequency Capacitor values used Series resistor, if used, and its value and type Device VDD rise time System temperature Oscillator mode selection of device (selects the gain of the internal oscillator inverter) • Crystal quality • Oscillator circuit layout • System noise The course of a typical crystal or resonator start-up is shown in Figure 3-4. Notice that the time to achieve stable oscillation is not instantaneous. EXAMPLE OSCILLATOR/RESONATOR START-UP CHARACTERISTICS Maximum VDD of System Device VDD VIH Voltage VIL 0V Crystal Start-up Time Time DS30000575C-page 54  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 3.6.2 PRIMARY OSCILLATOR START-UP FROM SLEEP MODE The most difficult time for the oscillator to start-up is when waking up from Sleep mode. This is because the load capacitors have both partially charged to some quiescent value and phase differential at wake-up is minimal. Thus, more time is required to achieve stable oscillation. Also remember that low voltage, high temperatures and the lower frequency clock modes also impose limitations on loop gain, which in turn, affects start-up. Each of the following factors increases the start-up time: • Low-frequency design (with a Low Gain Clock mode) • Quiet environment (such as a battery-operated device) • Operating in a shielded box (away from the noisy RF area) • Low voltage • High temperature • Wake-up from Sleep mode Circuit noise, on the other hand, may actually help to “kick start” the oscillator and help to lower the oscillator start-up time. 3.6.3 OSCILLATOR START-UP TIMER In order to ensure that a crystal oscillator (or ceramic resonator) has started and stabilized, an Oscillator Start-up Timer (OST) is provided. The OST is a simple, 10-bit counter that counts 1024 TOSC cycles before releasing the oscillator clock to the rest of the system. This time-out period is designated as TOST. The amplitude of the oscillator signal must reach the VIL and VIH thresholds for the oscillator pins before the OST can begin to count cycles. The TOST interval is required every time the oscillator has to restart (i.e., on POR, BOR and wake-up from Sleep mode). The Oscillator Start-up Timer is applied to the MS and HS modes for the Primary Oscillator, as well as the Secondary Oscillator, SOSC (see Section 3.9 “Secondary Oscillator (SOSC)”). 3.6.4 TUNING THE OSCILLATOR CIRCUIT Since Microchip devices have wide operating ranges (frequency, voltage and temperature, depending on the part and version ordered), and external components (crystals, capacitors, etc.) of varying quality and manufacture, validation of operation needs to be performed to ensure that the component selection will comply with the requirements of the application. There are many factors that go into the selection and arrangement of these external components. Depending on the application, these may include any of the following:  2012-2016 Microchip Technology Inc. • • • • • • • • • • • • Amplifier gain Desired frequency Resonant frequency(s) of the crystal Temperature of operation Supply voltage range Start-up time Stability Crystal life Power consumption Simplification of the circuit Use of standard components Component count 3.6.5 DETERMINING THE BEST VALUES FOR OSCILLATOR COMPONENTS The best method for selecting components is to apply a little knowledge, and a lot of trial measurement and testing. Crystals are usually selected by their parallel resonant frequency only; however, other parameters may be important to your design, such as temperature or frequency tolerance. Microchip Application Note AN588, “PICmicro® Microcontroller Oscillator Design Guide” (DS00000588) is an excellent reference to learn more about crystal operation and ordering information. The PIC18F internal oscillator circuit is a parallel oscillator circuit which requires that a parallel resonant crystal be selected. The load capacitance is usually specified in the 22 pF to 33 pF range. The crystal will oscillate closest to the desired frequency, with a load capacitance in this range. It may be necessary to alter these values, as described later, in order to achieve other benefits. The clock mode is primarily chosen based on the desired frequency of the crystal oscillator. The main difference between the MS and HS Oscillator modes is the gain of the internal inverter of the oscillator circuit, which allows the different frequency ranges. In general, use the oscillator option with the lowest possible gain that still meets specifications. This will result in lower dynamic currents (IDD). The frequency range of each oscillator mode is the recommended frequency cutoff, but the selection of a different gain mode is acceptable as long as a thorough validation is performed (voltage, temperature and component variations, such as resistor, capacitor and internal oscillator circuitry). C1 and C2 should also be initially selected based on the load capacitance, as suggested by the crystal manufacturer, and the tables supplied in the device data sheet. The values given in the device data sheet can only be used as a starting point, since the crystal manufacturer, supply voltage, and other factors already mentioned, may cause your circuit to differ from the one used in the factory characterization process. Ideally, the capacitance is chosen so that it will oscillate at the highest temperature and the lowest VDD that the circuit will be expected to perform under. High tempera- DS30000575C-page 55 PIC18F97J94 FAMILY ture and low VDD both have a limiting effect on the loop gain, such that if the circuit functions at these extremes, the designer can be more assured of proper operation at other temperatures and supply voltage combinations. The output sine wave should not be clipped in the highest gain environment (highest VDD and lowest temperature) and the sine output amplitude should be large enough in the lowest gain environment (lowest VDD and highest temperature) to cover the logic input requirements of the clock, as listed in the device data sheet. OSC1 may have specified VIL and VIH levels (refer to the specific product data sheet for more information). A method for improving start-up is to use a value of C2 greater than C1. This causes a greater phase shift across the crystal at power-up, which speeds oscillator start-up. Besides loading the crystal for proper frequency response, these capacitors can have the effect of lowering loop gain if their value is increased. C2 can be selected to affect the overall gain of the circuit. A higher C2 can lower the gain if the crystal is being overdriven (also see discussion on Rs). Capacitance values that are too high can store and dump too much current through the crystal, so C1 and C2 should not become excessively large. Unfortunately, measuring the wattage through a crystal is difficult, but if you do not stray too far from the suggested values, you should not have to be concerned with this. A series resistor, Rs, is added to the circuit if after all other external components are selected to satisfaction, and the crystal is still being overdriven. This can be determined by looking at the OSC2 pin, which is the driven pin, with an oscilloscope. Connecting the probe to the OSC1 pin will load the pin too much and negatively affect performance. Remember that a scope probe adds its own capacitance to the circuit, so this may have to be accounted for in your design (i.e., if the circuit worked best with a C2 of 22 pF and the scope probe was 10 pF, a 33 pF capacitor may actually be called for). The output signal should not be clipping or flattened. Overdriving the crystal can also lead to the circuit jumping to a higher harmonic level, or even, crystal damage. The OSC2 signal should be a clean sine wave that easily spans the input minimum and maximum of the clock input pin. An easy way to set this is to again test the circuit at the minimum temperature and maximum VDD that the design will be expected to perform in; then, look at the output. This should be the maximum amplitude of the clock output. If there is clipping, or the sine wave is distorted near VDD and VSS, increasing load capacitors may cause too much current to flow through the crystal, or push the value too far from the manufacturer’s load specification. To adjust the crystal current, add a trimmer potentiometer between the crystal DS30000575C-page 56 inverter output pin and C2, and adjust it until the sine wave is clean. The crystal will experience the highest drive currents at the low temperature and high VDD extremes. The trimmer potentiometer should be adjusted at these limits to prevent overdriving. A series resistor, Rs, of the closest standard value can now be inserted in place of the trimmer. If Rs is too high, perhaps more than 20 k, the input will be too isolated from the output, making the clock more susceptible to noise. If you find a value this high is needed to prevent overdriving the crystal, try increasing C2 to compensate or changing the oscillator operating mode. Try to get a combination where Rs is around 10 k or less, and load capacitance is not too far from the manufacturer’s specification. 3.7 External Clock Input In EC mode, the OSC1 pin is in a high-impedance state and can be driven by CMOS drivers. The OSC2 pin can be configured as either an I/O or the clock output (FOSC 4) by selecting the CLKOEN bit (CONFIG2L). With CLKOEN set (Figure 3-5), the clock output is available for testing or synchronization purposes. With CLKOEN clear (Figure 3-6), the OSC2 pin becomes a general purpose I/O pin. The feedback device between OSC1 and OSC2 is turned off to save current. FIGURE 3-5: EXTERNAL CLOCK INPUT OPERATION (CLKOEN = 1) Clock from External System OSC1 PIC18F FOSC/2 FIGURE 3-6: Clock from External System OSC2 (FOSC/4 output) EXTERNAL CLOCK INPUT OPERATION (CLKOEN = 0) OSC1 PIC18F I/O I/O RA6 (General Purpose I/O)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 3.8 Phase Lock Loop (PLL) Branch The PLL module contains two separate PLL submodules: PLLM and PLL96MHZ. The PLLM submodule is configurable as a 4x, 6x or 8x PLL. The PLL96MHZ submodule runs at 96 MHz and requires an input clock between 4 MHz and 48 MHz (a multiple of 4 MHz). These are selected through the PLLDIV bits. FIGURE 3-7: BASIC OSCILLATOR BLOCK DIAGRAM FRCDIV FRC Oscillator (FRC) Divide by N OSCMUX PLL Module (PLLM, PLL96MHZ) Primary Oscillator (POSC)  2012-2016 Microchip Technology Inc. DS30000575C-page 57 PIC18F97J94 FAMILY 3.8.1 OSCILLATOR MODES AND USB OPERATION Because of the timing requirements imposed by USB, an internal clock of 48 MHz is required at all times while the USB module is enabled and not in a suspended operating state. A method is provided to internally generate both the USB and system clocks from a single oscillator source. PIC18F97J94 family devices use the same clock structure as most other PIC18 devices, but include a two-branch PLL system to generate the two clock signals. The USB PLL block is shown in Figure 3-8. In this system, the input from the Primary Oscillator is divided down by a PLL prescaler to generate a 4 MHz output. FIGURE 3-8: This is used to drive an on-chip 96 MHz PLL frequency multiplier to drive the two clock branches. One branch uses a fixed, divide-by-2 frequency divider to generate the 48 MHz USB clock. The other branch uses a fixed, divide-by-1.5 frequency divider and configurable PLL prescaler/divider to generate a range of system clock frequencies. The CPDIVx bits select the system clock speed; available clock options are listed in Table 3-3. The USB PLL prescaler does not automatically sense the incoming oscillator frequency. The user must manually configure the PLL divider to generate the required 4 MHz output, using the PLLDIV Configuration bits. This limits the choices for Primary Oscillator frequency to a total of 8 possibilities, shown in Table 3-4. 96 MHz PLL BLOCK USB Clock 48 MHz Clock for USB Module ÷2 96 MHz PLL System Clock Input from FRC 4 MHz or 8 MHz PLLDIV ÷12 ÷8 ÷6 ÷5 ÷4 ÷3 ÷2 ÷1 0111 0110 0101 0100 0011 0010 0001 0000 Postsclaer Input from POSC PLL Prescaler FOSC ÷8 ÷4 ÷2 ÷1 11 10 01 00 ÷ 1.5 PLL Output for System Clock CPDIV Graphics Clock ÷2 Graphics Clock Option 2 48 MHz Branch 4 MHz Branch 96 MHz Branch G1CLKSEL 0 DS30000575C-page 58 Postsclaer 96 MHz PLL ÷64 ÷63 ... ÷17.50 ÷17.00 ... ÷1.25 127 126 ... 65 64 ... 1 Clock Output for Display Interface (DISPCLK)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 3-3: SYSTEM CLOCK OPTIONS DURING USB OPERATION MCU Clock Division (CPDIV) System Clock Frequency (Instruction Rate in MIPS®) None (00) 64 MHz (16) 2 (01) 32 MHz (8) 4 (10) 16 MHz (4) 8 (11) (1) 8 MHz (2) Note 1: These options are not compatible with USB operation. They may be used whenever the PLL branch is selected and the USB module is disabled. TABLE 3-4: VALID PRIMARY OSCILLATOR CONFIGURATIONS FOR USB OPERATIONS Input Oscillator Frequency Clock Mode PLL Division (PLLDIV) 48 MHz ECPLL 12 (111) 32 MHz ECPLL 8 (110) 24 MHz HSPLL, ECPLL 6 (101) 20 MHz HSPLL, ECPLL 5 (100) 16 MHz HSPLL, ECPLL 4 (011) 3.8.2 CONSIDERATIONS FOR USING THE PLL BLOCK All PLL blocks use the LOCK bit (OSCCON2) as a read-only Status bit to indicate the lock status of the PLL. It is automatically set after the typical time delay for the PLL to achieve lock, designated as TLOCK. It is cleared at a POR and on clock switches when the PLL is selected as a clock source. It remains clear when any clock source not using the PLL is selected. If the PLL does not stabilize properly during start-up, the LOCK bit may not reflect the actual status of the PLL lock, nor does it detect when the PLL loses lock during normal operation. Refer to the ”Electrical Characteristics” section in the specific device data sheet for further information on the PLL lock interval. Using any PLL block with the FRC Oscillator provides a stable system clock for microcontroller operations. USB operation is only possible with FRC Oscillators that are implemented with ±1/4% frequency accuracy. Serial communications using USART are only possible when FRC Oscillators are implemented with ±2% frequency accuracy. The PIC18F97J94 family is able to meet the required oscillator accuracy for both USB and USART providing stable communication by use of its active clock tuning feature. Refer to Section 3.13.3 “Active Clock Tuning (ACT) Module” for more information. 12 MHz HSPLL, ECPLL 3 (010) 8 MHz ECPLL, MSPLL, FRCPLL(1) 2 (001) If an application is being migrated between PIC18F platforms with different PLL blocks, the differences in PLL and clock options may require the reconfiguration of peripherals that use the system clock. This is particularly true with serial communication peripherals, such as the USARTs. 4 MHz ECPLL, MSPLL, FRCPLL(1) 1 (000) 3.9 Note 1: FRCPLL with ±0.25% accuracy can be used for USB operation. Note: Because of USB clocking accuracy requirements (±0.25%), not all PIC18F devices support the use of the FRCPLL system clock configuration for USB operation. Refer to the specific device data sheet for details on the FRC Oscillator module. Secondary Oscillator (SOSC) In most PIC18F devices, the low-power Secondary Oscillator (SOSC) is implemented to run with a 32.768 kHz crystal. The oscillator is located on the SOSCO and SOSCI device pins, and serves as a secondary crystal clock source for low-power operation. It is used to drive Timer1, Real-Time Clock and Calendar (RTCC) and other modules requiring a clock signal while in low-power operation. 3.9.1 ENABLING THE SECONDARY OSCILLATOR The operation of the SOSC is selected by the FOSCx Configuration bits or by selection of the NOSCx bits (OSCCON). The SOSC can also be enabled by setting the SOSCEN bit in Timer1, Timer3 or Timer5. The SOSC has a long start-up time; therefore, to avoid delays for peripheral start-up, the SOSC can be manually started using one of the SOSCEN bits.  2012-2016 Microchip Technology Inc. DS30000575C-page 59 PIC18F97J94 FAMILY 3.9.2 3.9.2.1 SECONDARY OSCILLATOR OPERATION Continuous Operation The SOSC is always running when any of the SOSCEN bits are set. Leaving the oscillator running at all times allows a fast switch to the 32 kHz system clock for lower power operation. Returning to the faster main oscillator still requires an oscillator start-up time if it is a crystal-type source. This start-up time can be avoided on PLL clock sources by setting the PLLEN bit (OSCCON4) in advance of switching the clock source. In addition, the oscillator will need to remain running at all times for Real-Time Clock (RTC) application using Timer1 or the RTCC module. Refer to Section 14. “Timers” and Section 29. “Real-Time Clock and Calendar (RTCC)” in the “PIC18F Family Reference Manual” for further details. 3.9.2.2 Intermittent Operation When all SOSCEN bits are cleared, the oscillator will only operate when it is selected as the current device clock source (COSC = 100). It will be disabled automatically if it is the current device clock source and the device enters Sleep mode. 3.9.3 3.9.3.1 OPERATING MODES Digital Mode The SOSCO pin can also be configured to operate as a digital clock input. The SOSCO pin is configured as a digital input by setting SOSCSEL (CONFIG2L) = 10. When running in this mode, the SOSCO/SCLKI pin will operate as a digital input to the oscillator section, while the SOSCI pin will function as a port pin. The crystal driving circuit is disabled. The Oscillator Configuration Fuse bits (FOSC) and New Oscillator Selection bits (NOSC) have no effect. 3.9.4 SOSC CRYSTAL SELECTION A typical 50K ESR and 12.5 pF CL (capacitive loading) rated crystal is recommended for reliable operation of the SOSC. The duty cycle of the SOSC output can be measured on the REFO pin, and is recommended to be within +/-15% from a 50% duty cycle. 3.10 Internal Fast RC Oscillator (FRC) The FRC Oscillator is a fast (8 MHz nominal), internal RC Oscillator. This oscillator is intended to be a precise internal RC Oscillator accurate enough to provide the clock frequency necessary to maintain baud rate tolerance for serial data transmissions, without the use of an external crystal or ceramic resonator. The PIC18F device operates from the FRC Oscillator whenever the COSCx bits are ‘111’, ‘110’, ‘001’ or ‘000’. DS30000575C-page 60 3.10.1 ENABLING THE FRC OSCILLATOR Since it serves as the system clock during device initialization, the FRC Oscillator is always enabled at a POR. After the device is configured and PWRT expires, FRC remains active only if it is selected as the device clock source. 3.10.2 FRC POSTSCALER MODE (FRCDIV) Users are not limited to the nominal 8 MHz FRC output if they wish to use the Fast Internal Oscillator as a clock source. An additional FRC mode, FRCDIV, implements a selectable postscaler that allows the choice of a lower clock frequency, from 7 different options, plus the direct 8 MHz output. The postscaler is configured using the IRCF bits (OSCCON3). Assuming a nominal 8 MHz output, available lower frequency options range from 4 MHz (divide-by-2) to 31 kHz (divide-by-256). The range of frequencies allows users the ability to save power at any time in an application by simply changing the IRCFx bits. The FRCDIV mode is selected whenever the COSCx bits are ‘111’. 3.10.3 FRC OSCILLATOR WITH PLL MODE (FRCPLL) The FRCPLL mode is selected whenever the COSCx bits are ‘001’. In addition, this mode only functions when the direct or divide-by-2 FRC postscaler options are selected (IRCF = 000 or 001). When using the 4x or 8x PLL option, the output of the FRC postscaler may also be combined with the PLL to produce a nominal system clock of 16 MHz, 32 MHz or 64 MHz. Although somewhat less precise in frequency than using the Primary Oscillator with a crystal or resonator, it allows high-speed operation of the device without the use of external oscillator components. For devices with the basic 4x PLL block, the output of the FRC postscaler block may also be combined with the PLL to produce a nominal system clock of either 16 MHz or 32 MHz. Although somewhat less precise in frequency than using the Primary Oscillator with a crystal or resonator, it still allows high-speed operation of the device without the use of external oscillator components. When using the 96 MHz PLL block, the output of the FRC postscaler block may also be combined with the PLL to produce a nominal system clock of either 4 MHz, 8 MHz, 16 MHz or 32 MHz. It also produces a 48 MHz USB clock; however, this USB clock must be generated with the FRC Oscillator meeting the frequency accuracy requirement of USB for proper operation. Refer to the specific device data sheet for details on the FRC Oscillator electrical characteristics.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY In cases where the frequency accuracy is not met for USB operation, the FRCPLL mode should not be used when USB is active. Note: 3.11 Using FRC postscaler values, other than ‘000‘or ‘001‘, will cause the clock input to the PLL to be below the operating frequency input range and may cause undesirable operation. Internal Low-Power RC Oscillator (LPRC) The LPRC Oscillator is separate from the FRC and oscillates at a nominal frequency of 31 kHz. LPRC is the clock source for the Power-up Timer (PWRT), Watchdog Timer (WDT) and FSCM circuits. It may also be used to provide a low-frequency clock source option for the device, in those applications where power consumption is critical and timing accuracy is not required. 3.11.1 ENABLING THE LPRC OSCILLATOR Since it serves the Power-up Timer (PWRT) clock source, the LPRC Oscillator is enabled at POR events whenever the on-board voltage regulator is disabled. After the PWRT expires, the LPRC Oscillator will remain on if any one of the following is true: • The FSCM is enabled. • The WDT is enabled. • The LPRC Oscillator is selected as the system clock (COSC = 101). If none of the above is true, the LPRC will shut off after the PWRT expires. 3.12 Fail-Safe Clock Monitor (FSCM) The Fail-Safe Clock Monitor (FSCM) allows the device to continue to operate, even in the event of an oscillator failure. The FSCM function is enabled by programming the FSCMx (Clock Switch and Monitor) bits in CONFIG3L. FSCM is only enabled when the FSCM bits (CONFIG3L) = 00. When FSCM is enabled, the internal LPRC Oscillator will run at all times (except during Sleep mode). In the event of an oscillator failure, the FSCM will generate a clock failure trap and will switch the system clock to the FRC Oscillator. The user will then have the option to either attempt to restart the oscillator or execute a controlled shutdown. FSCM will monitor the system clock source regardless of its source or oscillator mode. This includes the Primary Oscillator for all oscillator modes and the Secondary Oscillator, SOSC, when configured as the system clock. The FSCM module takes the following actions when switching to the FRC Oscillator: 1. 2. The COSCx bits are loaded with ‘000’. The CF Status bit is set to indicate the clock  2012-2016 Microchip Technology Inc. failure. Note: 3.12.1 For more information about the oscillator failure trap, refer to Section 10.0 “Interrupts”. FSCM DELAY On a POR, BOR or wake from Sleep mode event, a nominal delay (TFSCM) may be inserted before the FSCM begins to monitor the system clock source. The purpose of the FSCM delay is to provide time for the oscillator and/or PLL to stabilize when the PWRT is not utilized. The FSCM delay will be generated after the internal System Reset signal, SYSRST, has been released. Refer to Section 28.4 “Fail-Safe Clock Monitor” for FSCM delay timing information. The TFSCM interval is applied whenever the FSCM is enabled and the EC, HS or SOSC Oscillator modes are selected as the system clock. Note: 3.12.2 Refer to the “Electrical Characteristics” section of the specific device data sheet for TFSCM specification values. FSCM AND SLOW OSCILLATOR START-UP If the chosen device oscillator has a slow start-up time coming out of POR, BOR or Sleep mode, it is possible that the FSCM delay will expire before the oscillator has started. In this case, the FSCM will initiate a clock failure trap. As this happens, the COSCx bits are loaded with the FRC Oscillator selection. This will effectively shut off the original oscillator that was trying to start. The user can detect this situation and initiate a clock switch back to the desired oscillator in the Trap Service Routine (TSR). 3.12.3 FSCM AND WDT The FSCM and the WDT both use the LPRC Oscillator as their time base. In the event of a clock failure, the WDT is unaffected and continues to run on the LPRC. 3.13 Clock Switching Operation With few limitations, applications are free to switch between any of the four clock sources (Primary, SOSC, FRC and LPRC) under software control and at any time. To limit the possible side effects that could result from this flexibility, PIC18F devices have a safeguard lock built into the switch process. Note: Primary Oscillator mode has three different submodes (MS, HS and EC), which are determined by the POSCMDx Configuration bits. While an application can switch to and from Primary Oscillator mode, in software, it cannot switch between the different primary submodes without reprogramming the device. DS30000575C-page 61 PIC18F97J94 FAMILY 3.13.1 ENABLING CLOCK SWITCHING To enable clock switching, the FCKSM1 Configuration bit must be programmed to ‘0’. If the FCKSM1 Configuration bit is unprogrammed (‘1’), the clock switching function and Fail-Safe Clock Monitor function are disabled; this is the default setting. The NOSCx control bits (OSCCON) do not control the clock selection when clock switching is disabled. However, the COSCx bits (OSCCON) will reflect the clock source selected by the FOSC Configuration bits. 3.13.2 OSCILLATOR SWITCHING SEQUENCE 2. 3. 3. 4. 5. At a minimum, performing a clock switch requires this basic sequence: 1. 2. If desired, read the COSCx bits (OSCCON) to determine the current oscillator source. Clear the CLKLOCK bit (OSCCON2) to enable writes to the NOSCx bits (OSCCON). Write the appropriate value to the NOSCx control bits (OSCCON) for the new oscillator source. initiated. The new oscillator is turned on by the hardware if it is not currently running. If a crystal oscillator must be turned on, the hardware will wait until the OST expires. If the new source is using the PLL, then the hardware waits until a PLL lock is detected (LOCK = 1). The hardware waits for the new clock source to stabilize and then performs the clock switch. The NOSCx bit values are transferred to the COSCx Status bits. The old clock source is turned off at this time, with the exception of LPRC (if WDT or FSCM is enabled) or SOSC (if it is enabled by one of the timer sources). The timing of the transition between clock sources is shown in Figure 3-9. Note 1: The processor will continue to execute code throughout the clock switching sequence. Timing-sensitive code should not be executed during this time. Once the basic sequence is completed, the system clock hardware responds automatically as follows: 1. The clock switching hardware compares the COSC Status bits with the new value of the NOSC control bits. If they are the same, then the clock switch is a redundant operation. If they are different, then a valid clock switch has been FIGURE 3-9: 2: Direct clock switches between any Primary Oscillator mode with PLL and FRCPLL mode are not permitted. This applies to clock switches in either direction. In these instances, the application must switch to FRC mode as a transition clock source between the two PLL modes. CLOCK TRANSITION TIMING DIAGRAM New Source Enabled New Source Stable Old Source Disabled Old Clock Source New Clock Source System Clock NOSC = COSC (old oscillator enabled) NOSC ≠ COSC (oscillator source in process of transition) NOSC = COSC (new oscillator source enabled) Both Oscillators Active Note: The system clock can be any selected source (Primary, Secondary, FRC or LPRC). DS30000575C-page 62  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY A recommended code sequence for a clock switch includes the following: 1. 2. 3. 4. 5. 6. Disable interrupts during the OSCCON register unlock and write sequence. Clear the CLKLOCK bit (OSCCON2) to enable writes to the NOSCx bits (OSCCON). Write new oscillator source to NOSCx control bits. Continue to execute code that is not clocksensitive (optional). Invoke an appropriate amount of software delay (cycle counting) to allow the selected oscillator and/or PLL to start and stabilize. Check to see if COSC contains the new oscillator values that were requested in Step 3. 3.13.2.1 Clock Switching Considerations When incorporating clock switching into an application, users should keep certain things in mind when designing their code. • If the new clock source is a crystal oscillator, the clock switch time will be dominated by the oscillator start-up time. • If the new clock source does not start, or is not present, the clock switching hardware will wait indefinitely for the new clock source. The user can detect this situation because the COSCx bits will not change to reflect the new desired oscillator settings. • Switching to a low-frequency clock source, such as the Secondary Oscillator, will result in very slow device operation. Note: 3.13.3 The application should not attempt to switch to a clock with a frequency lower than 100 kHz when the FSCM is enabled. Clock switching in these instances may generate a false oscillator fail trap and result in a switch to the Internal Fast RC Oscillator. ACTIVE CLOCK TUNING (ACT) MODULE The Active Clock Tuning (ACT) module continuously adjusts the 8 MHz internal oscillator, using an available external reference, to achieve ± 0.20% accuracy. This eliminates the need for a high-speed, high-accuracy external crystal when the system has an available lower speed, lower power, high-accuracy clock source available. Systems implementing a RealTime Clock Calendar (RTCC) or a full-speed USB application can take full advantage of the ACT module.  2012-2016 Microchip Technology Inc. 3.13.3.1 Active Clock Tuning Operation The ACT module defaults to the disabled state after any Reset. When the ACT module is disabled, the user can write to the TUN bits in the OSCTUNE register to manually adjust the 8 MHz internal oscillator. The module is enabled by setting the ACTEN bit of the ACTCON register. When enabled, the ACT module takes control of the OSCTUNE register. The ACT module uses the selected ACT reference clock to tune the 8 MHz internal oscillator to an accuracy of 8 MHz ± 0.2%. The tuning automatically adjusts the OSCTUNE register every reference clock cycle. 3.13.3.2 Active Clock Tuning Source Selection The ACT reference clock is selected with the ACTSRC bit of the ACTCON register. The reference clock sources are provided by the: • USB module in full-speed operation (ACT_clk) • Secondary clock at 32.768 kHz (SOSC_clk) 3.13.3.3 ACT Lock Status The ACTLOCK bit will be set to ‘1’, when the 8 MHz internal oscillator is successfully tuned. The bit will be cleared by the following conditions: • Out of Lock condition • Device Reset • Module is disabled 3.13.3.4 ACT Out-of-Range Status If the ACT module requires an OSCTUNE value outside the range to achieve ± 0.20% accuracy, then the ACT Out-of-Range (ACTORS) Status bit will be set to ‘1’. An out-of-range status can occur: • When the 8 MHZ internal oscillator is tuned to its lowest frequency and the next ACT_clk event requests a lower frequency. • When the 8 MHZ internal oscillator is tuned to its highest frequency and the next ACT_clk event requests a higher frequency. When the ACT out-of-range event occurs, the 8 MHz internal oscillator will continue to use the last written OSCTUNE value. When the OSCTUNE value moves back within the tunable range and ACTLOCK is established, the ACTORS bit is cleared to ‘0’. DS30000575C-page 63 PIC18F97J94 FAMILY Note 1: When the ACT module is enabled, the OSCTUNE register is only updated by the module. Writes to the OSCTUNE register by the user are inhibited, but reading the register is permitted. 2: After disabling the ACT module, the user should wait three instructions before writing to the OSCTUNE register. FIGURE 3-10: ACTIVE CLOCK TUNING BLOCK DIAGRAM ACTEN ACTSRC FSUSB_clk 1 SOSC_clk 0 ACT_clk Enable Active Clock Tuning Module 8 MHz Internal OSC ACT data 7 ACTUD ACTEN DS30000575C-page 64 sfr data 7 OSCTUNE Write OSCTUNE ACTEN  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 3-10: ACTCON: ACTIVE CLOCK TUNING (ACT) CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 ACTEN — ACTSIDL ACTSRC(1) R-0 R/W-0 ACTLOCK ACTLOCKPOL R-0 R/W-0 ACTORS ACTORSPOL bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 ACTEN: Active Clock Tuning Selection bit 1 = ACT module is enabled, updates to OSCTUNE are exclusive to the ACT module 0 = ACT module is disabled bit 6 Unimplemented: Reads as ‘0’ bit 5 ACTSIDL: Active Clock Tuning Stop in Idle bit 1 = Active clock tuning stops during Idle mode 0 = Active clock tuning continues during Idle mode bit 4 ACTSRC: Active Clock Tuning Source Selection bit 1 = The FRC oscillator is tuned to approximately match the USB host clock tolerance 0 = The FRC oscillator is tuned to approximately match the 32.768 kHz SOSC tolerance bit 3 ACTLOCK: Active Clock Tuning Lock Status bit 1 = Locked; internal oscillator is within ± 0.20% 0 = Not locked; internal oscillator tuning has not stabilized within ± 0.20% bit 2 ACTLOCKPOL: Active Clock Tuning Lock Interrupt Polarity bit 1 = ACT lock interrupt is generated when ACTLOCK is ‘0’ 0 = ACT lock interrupt is generated when ACTLOCK is ‘1’ bit 1 ACTORS: Active Clock Tuning Out-of-Range Status bit 1 = Out-of-range; oscillator frequency is outside of the OSCTUNE range 0 = In-range; oscillator frequency is within the OSCTUNE range bit 0 ACTORSPOL: Active Clock Tuning Out of Range Interrupt Polarity bit 1 = ACT out of range interrupt is generated when ACTORS is ‘0’ 0 = ACT out of range interrupt is generated when ACTORS is ‘1’ Note 1: The ACTSRC bit should only be changed when ACTEN = 0.  2012-2016 Microchip Technology Inc. DS30000575C-page 65 PIC18F97J94 FAMILY 3.13.4 ABANDONING A CLOCK SWITCH In the event the clock switch does not complete, it can be abandoned by setting the NOSCx bits to their previous values. This abandons the clock switch process, stops and resets the OST (if applicable), and stops the PLL (if applicable). A clock switch procedure can be aborted at any time. A clock switch that is already in progress can also be aborted by performing a second clock switch. 3.13.5 ENTERING SLEEP MODE DURING A CLOCK SWITCH If the device enters Sleep mode during a clock switch operation, the operation is abandoned. The processor keeps the old clock selection and the NOSCx bits return to their previous values (the same as COSC). The SLEEP instruction is then executed normally. 3.14 Two-Speed Start-Up Two-Speed Start-up is an automatic clock switching feature that is independent of the manually controlled clock switching previously described. It helps to minimize the latency period, from oscillator start-up to code execution, by allowing the microcontroller to use the FRC Oscillator as a clock source until the primary clock source is available. This feature is controlled by the IESO Configuration bit (CONFIG2L) and operates independently of the state of the FSCM Configuration bits. Two-Speed Start-up is particularly useful when an external oscillator is selected by the FOSCx Configuration bits, and a crystal-based oscillator (either a Primary or Secondary Oscillator) may have a longer start-up time. As an internal RC Oscillator, the FRC clock source is available almost immediately following a POR or device wake-up. With Two-Speed Start-up, the device starts executing code on POR in its default oscillator configuration (FRC). It continues to operate in this mode until the external oscillator source, specified by the FOSCx Configuration bits, becomes stable; at which time, it automatically switches to that source. Two-Speed Start-up is used on wake-up from the powersaving Sleep mode. The device uses the FRC clock source until the selected primary clock is ready. It is not used in Idle mode, as the device will be clocked by the currently selected clock source until the primary clock source becomes available. DS30000575C-page 66 3.14.1 SPECIAL CONSIDERATIONS FOR USING TWO-SPEED START-UP While using the FRC Oscillator in Two-Speed Start-up, the device still obeys the normal command sequences for entering power-saving modes, including SLEEP and IDLE instructions. In practice, this means that user code can change the NOSC bit settings or issue #SLEEP instructions before the OST times out. This would allow an application to briefly wake-up, perform routine “housekeeping” tasks and return to Sleep before the device starts to operate from the external oscillator. User code can also check which clock source is currently providing the device clocking by checking the status of the COSC bits against the NOSC bits. If these two sets of bits match, the clock switch has been completed successfully and the device is running from the intended clock source; the Primary Oscillator is providing the clock. Otherwise, FRC is providing the clock during wake-up from Reset or Sleep mode. 3.15 3.15.1 Reference Clock Output Module (REFO1 and REFO2) APPLICATIONS The PIC18F97J94 family has two Reference Clock Output modules. Each of the Reference Clock Output modules provides the user with the ability to send out a programmed output clock onto the REFO1or REFO2 pins. 3.15.2 REFERENCE CLOCK SOURCE The module provides the ability to select one of the following clock sources: • • • • • • Primary Crystal Oscillator (POSC) Secondary Crystal Oscillator (SOSC) 32.768 kHz Internal Oscillator (INTOSC) Fast Internal Oscillator (FRC) Raw System Clock (sys_clk) Peripheral Clock (p1_clk) It includes a programmable clock divider with ratios ranging from 1:1 to 1:65534. When the clock source is a crystal or internal oscillator, the RSLP bit (REFOxCON can be set to continue REFOx operation while the device is in Sleep Mode.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 3.15.3 CLOCK SYNCHRONIZATION The Reference Clock Output is enabled only once (ON = 1). Note that the source of the clock and the divider values should be chosen prior to the bit being set to avoid glitches on the REFO output. Once the ON bit is set, its value is synchronized to the reference clock domain to enable the output. This ensures that no glitches will be seen on the output. Similarly, when the ON bit is cleared, the output and the associated output enable signals will be synchronized, and disabled on the falling edge of the reference clock. Note that with large divider values, this will cause the REFO to be enabled for some period after ON is cleared. 3.15.4 OPERATION IN SLEEP MODE If any clock source, other than the peripheral clock, is used as a base reference (i.e., ROSEL  0001), the user has the option to configure the behavior of the oscillator in Sleep mode. The RSLP Configuration bit determines if the oscillator will continue to run in Sleep. If RSLP = 0, the oscillator will be shut down in Sleep (assuming no other consumers are requesting it). If RSLP = 1, the oscillator will continue to run in Sleep. 3.15.5 MODULE ENABLE SIGNAL The REFOx module may be enabled or disabled using the REFOxMD register bit (PMD3, bit 1 or 0). The module also needs to be turned on using the ON bit (REFO1CON). 3.15.5.1 Registers and Bits This module provides the following device registers and/or bits: • REFOxCON – Reference Clock Output Control Register • REFOxCON1 – Reference Clock Output Control 1 Register • REFOxCON2 – Reference Clock Output Control 2 Register • REFOxCON3 – Reference Clock Output Control 3 Register The Reference Clock Output is synchronized with the Sleep signal to avoid any glitches on its output.  2012-2016 Microchip Technology Inc. DS30000575C-page 67 PIC18F97J94 FAMILY 4.0 POWER-MANAGED MODES All PIC18F97J94 Family devices offer a number of built-in strategies for reducing power consumption. These strategies can be particularly useful in applications, which are both power-constrained (such as battery operation), yet require periods of full-power operation for timing-sensitive routines (such as serial communications). Aside from their low-power architecture, these devices include an expanded range of dedicated hardware features that allow the microcontroller to reduce power consumption to even lower levels when long-term hibernation is required, and still be able to resume operation on short notice. The device has four power-saving features: • • • • Instruction-Based Power-Saving Modes Hardware-Based Power Reduction Features Microcontroller Clock Manipulation Selective Peripheral Control 4.1 Overview of Power-Saving Modes In addition to full-power operation, otherwise known as Run mode, PIC18F97J94 Family devices offer three instruction-based, power-saving modes and one hardware-based mode. In descending order of power consumption, they are: • • • • Idle Sleep (including retention Sleep) Deep Sleep (with and without retention) VBAT (with and without RTCC) By powering down all four modes, different functional areas of the microcontroller allow progressive reductions of operating and Idle power consumption. In addition, three of the modes can be tailored for more power reduction at a trade-off of some operating features. Table 4-1 lists all of the operating modes (including Run mode, for comparison) in order of increasing power savings and summarizes how the microcontroller exits the different modes. Combinations of these methods can be used to selectively tailor an application’s power consumption, while still maintaining critical or timing-sensitive application features. However, it is more convenient to discuss the strategies separately.  2012-2016 Microchip Technology Inc. DS30000575C-page 69 SUMMARY OF OPERATING MODES FOR PIC18F97J94 FAMILY DEVICES WITH VBAT POWER-SAVING FEATURES Exit Conditions Active Systems INT0 Only All POR MCLR RTCC Alarm (DS)WDT(3) VDD Restore Y Y Y Y N/A N/A N/A N/A N/A N/A N/A N/A N/A Y Y Y Y Y Y Y Y Y Y Y N/A Next Instruction Instruction N N(4) Y Y Y Y Y Y Y Y Y Y N/A Next Instruction Instruction + RETEN bit N (4) Y Y Y Y Y Y Y Y Y Y N/A Retention Deep Sleep Instruction + DSEN bit + RETEN bit N N Y Y Y N Y N Y Y Y Y N/A Next Instruction Deep Sleep Instruction + DSEN bit N N N Y Y N Y N Y Y Y Y N/A Reset Vector Reset Vector Core Run (default) Idle RTCC(1) Y N Entry Data RAM Retention N/A Instruction Mode Peripherals All Resets DSGPRx(2) Interrupts Code Execution Resumes Sleep modes: Sleep Retention Sleep N Deep Sleep modes: VBAT: with RTCC Hardware N N N Y Y N N N N N N N Y w/o RTCC Hardware + by disabling the RTCC PMD bit N N N N Y N N N N N N N Y  2012-2016 Microchip Technology Inc. Note 1: 2: 3: 4: If RTCC is otherwise enabled in firmware. Data retention in the DSGPR0, DSGPR1, DSGPR2 and DSGPR3 registers. Deep Sleep WDT in Deep Sleep modes; WDT in all other modes. Some select peripherals may continue to operate in this mode, using either the LPRC or an external clock source. PIC18F97J94 FAMILY DS30000575C-page 70 TABLE 4-1: PIC18F97J94 FAMILY 4.2 Instruction-Based Power-Saving Modes PIC18F97J94 Family devices have three instructionbased power-saving modes; two of these have additional features that allow for additional tailoring of power consumption. All three modes are entered through the execution of the SLEEP instruction. In descending order of power consumption, they are: • Idle Mode: The CPU is disabled, but the system clock source continues to operate. Peripherals continue to operate, but can optionally be disabled. • Sleep Modes: The CPU, system clock source and any peripherals that operate on the system clock source are disabled. • Deep Sleep Modes: The CPU system clock source, and all the peripherals except RTCC and DSWDT are disabled. This is the lowest power mode for the device. The power to RAM and Flash is also disabled. Deep Sleep modes represent the lowest power modes available without removing power from the application. Idle and Sleep modes are entered directly with the SLEEP statement. Having IDLEN (OSCCON) set prior to the SLEEP statement will put the device into Idle mode. For Deep Sleep mode, it is necessary to set the DSEN bit (DSCONH). To prevent inadvertent entry into Deep Sleep mode, and possible loss of data, the DSEN bit must be written to twice. The write need not be consecutive instructions; however, it is a better practice to write both, one after the other. It is also recommended to clear the DSCON1 register before setting the DSEN bit (Example 4-1). Note: SLEEP_MODE and IDLE_MODE are constants defined in the Assembler Include file for the selected device. EXAMPLE 4-1: clrf clrf bsf bsf sleep SLEEP ASSEMBLY SYNTAX DSCON1 DSCON1 DSCON1,7 DSCON1,7 or movlw movwf movwf sleep 0x80 DSCON1 DSCON1  2012-2016 Microchip Technology Inc. The instruction-based power-saving modes are exited as a result of several different hardware triggers. When the device exits one of these three operating modes, it is said to ‘wake-up’. The characteristics of the powersaving modes are described in the subsequent sections. 4.2.1 INTERRUPTS COINCIDENT WITH POWER SAVE INSTRUCTIONS Any interrupt that coincides with the execution of a SLEEP instruction will be held off until entry into Sleep, Idle or Deep Sleep mode is completed. The device will then wake-up from the power-managed mode. Interrupts that occur during the Deep Sleep unlock sequence will interrupt the mandatory unlock sequence and cause a failure to enter Deep Sleep. For this reason, it is recommended to disable all interrupts during the Deep Sleep unlock sequence. 4.2.2 RETENTION REGULATOR A second on-chip voltage regulator is used for power management in Sleep and Deep Sleep modes. This regulator, also known as the retention regulator, supplies core logic and other circuits with power at a lower VCORE level, about 1.2V nominal. Running these circuits at a lower voltage allows for an additional incremental power saving over the normal minimum VCORE level. In Retention Sleep modes, using the regulator maintains the entire data RAM and its contents, instead of just a few protected registers. This allows the device to exit a power-saving mode and resume code execution as its previous state. The retention regulator is controlled by the Configuration bit, RETEN (CONFIG7L), and the SRETEN bit (RCON4). The RETEN bit makes the retention regulator available for software control. By default (RETEN = 1), the regulator is disabled and the SRETEN bit has no effect. Programming RETEN (= 0) allows the SRETEN bit to control the regulator’s operation, leaving its use in power-saving modes at the user’s discretion. Setting the SRETEN bit prior to executing the SLEEP instruction puts the device into Retention Sleep mode. If the DSEN bit was also unlocked and set prior to the instruction, the device will enter Retention Deep Sleep mode. The retention regulator is not available outside of Sleep, Deep Sleep or VBAT modes. Enabling it while the device is operating in Run or Idle modes does not allow the device to operate at a lower level of VCORE. DS30000575C-page 71 PIC18F97J94 FAMILY 4.2.3 IDLE MODE When the device enters Idle mode, the following events occur: • The CPU will stop executing instructions. • The WDT is automatically cleared. • The system clock source will remain active and the peripheral modules, by default, will continue to operate normally from the system clock source. Peripherals can optionally be shut down in Idle mode using their ‘Stop in Idle’ control bit. (See peripheral descriptions for further details.) • If the WDT or FSCM is enabled, the LPRC will also remain active. The processor will wake-up from Idle mode on the following events: • On any interrupt that is individually enabled. • On any source of device Reset. • On a WDT time-out. Upon wake-up from Idle mode, the clock is reapplied to the CPU and instruction execution begins immediately, starting with the instruction following the SLEEP instruction, or the first instruction in the Interrupt Service Routine (ISR). 4.2.3.1 Time Delays on Wake-up from Idle Mode Unlike a wake-up from Sleep mode, there are no additional time delays associated with wake-up from Idle mode. The system clock is running during Idle mode, therefore, no start-up times are required at wake-up. 4.2.3.2 Wake-up from Idle on Interrupt Any source of interrupt that is individually enabled using the corresponding control bit in the PIEx register, will be able to wake-up the processor from Idle mode. When the device wakes from Idle mode, one of two options may occur: • If the GIE bit is set, the processor will wake and the Program Counter will begin execution at the interrupt vector. • If the GIE bit is not set, the processor will wake and the Program Counter will continue execution following the SLEEP instruction. The PD Status bit (RCON) is set upon wake-up. DS30000575C-page 72 4.2.3.3 Wake-up from Idle on Reset Any Reset, other than a Power-on Reset (POR), will wake-up the CPU from Idle mode on any device Reset, except a POR. 4.2.3.4 Wake-up from Idle on WDT Time-out If the WDT is enabled, then the processor will wake-up from Idle mode on a WDT time-out and continue code execution with the instruction following the SLEEP instruction that initiated Idle mode. Note that the WDT time-out does not reset the device in this case. The TO bit (RCON) will be set. 4.2.4 SLEEP MODES Most 08KA101 family devices that incorporate powersaving features and VBAT, offer two distinct Sleep modes: Sleep mode and Retention Sleep mode. The characteristics of both Sleep modes are: • The system clock source is shut down. If an onchip oscillator is used, it is turned off. • The device current consumption will be optimum, provided no I/O pin is sourcing the current. • The Fail-Safe Clock Monitor (FSCM) does not operate during Sleep mode since the system clock source is disabled. • The LPRC clock will continue to run in Sleep mode if the WDT is enabled. • If Brown-out Reset (BOR) is enabled, the Brownout Reset (BOR) circuit remains operational during Sleep mode. • The WDT, if enabled, is automatically cleared prior to entering Sleep mode. • Some peripherals may continue to operate in Sleep mode. These peripherals include I/O pins that detect a change in the input signal or peripherals that use an external clock input. Any peripheral that operates from the system clock source will be disabled in Sleep mode. The processor will exit, or ‘wake-up’ from Sleep on one of the following events: • On any interrupt source that is individually enabled • On any form of device Reset • On a WDT time-out  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 4.2.4.1 Retention Sleep Mode Retention Sleep mode allows for additional power savings over Sleep mode by maintaining key systems from the lower power retention regulator. When the retention regulator is used, the normal on-chip voltage regulator (operating at 1.8V nominal) is turned off and will enable a low-power (1.2V typical) regulator. By using a lower voltage, a lower total power consumption is achieved. Retention Sleep also offers the advantage of maintaining the contents of the data RAM. As a trade-off, the wake-up time is longer than that for Sleep mode. 4.3.4 WAKE-UP FROM SLEEP ON WATCHDOG TIME-OUT If the Watchdog Timer (WDT) is enabled and expires while the device is in Sleep mode, the processor will wake-up. The SWDTEN Status bit (RCON2) is set to indicate that the device resumed operation due to the WDT expiration. Note that this event does not reset the device. Operation continues from the instruction following the SLEEP instruction that initiated Sleep mode. 4.3.5 CONTROL BIT SUMMARY FOR SLEEP MODES Retention Sleep mode is controlled by the SRETEN bit (RCON4) and the RETEN Configuration bit, as described in Section 4.2.2, Retention Regulator. Table 4-2 shows the settings for the bits relevant to Sleep modes. 4.3 TABLE 4-2: Clock Source Considerations When the device wakes up from either of the Sleep modes, it will restart the same clock source that was active when Sleep mode was entered. Wake-up delays for the different oscillator modes are shown in Table 43 and Table 4-4, respectively. If the system clock source is derived from a crystal oscillator and/or the PLL, the Oscillator Start-up Timer (OST) and/or PLL lock times must be applied before the system clock source is made available to the device. As an exception to this rule, no oscillator delays are necessary if the system clock source is the Secondary Oscillator and it was running while in Sleep mode. 4.3.1 SLOW OSCILLATOR START-UP The OST and PLL lock times may not have expired when the power-up delays have expired. Mode Sleep Retention Sleep 4.3.6 BIT SETTINGS FOR ALL SLEEP MODES DSEN DSCONH Retention Regulator SRETEN RETEN CONFIG7L RCON4 State x 1 x Disabled x 0 0 Disabled x 0 1 Enabled WAKE-UP DELAYS The restart delay, associated with waking up from Sleep and Retention Sleep modes, parallel each other in terms of clock start-up times. They differ in the time it takes to switch over from their respective regulators. The delays for the different oscillator modes are shown in Table 4-3 and Table 4-4, respectively. To avoid this condition, one can enable Two-Speed Start-up by the device that will run on FRC until the clock source is stable. Once the clock source is stable, the device will switch to the selected clock source. 4.3.2 WAKE-UP FROM SLEEP ON INTERRUPT Any source of interrupt that is individually enabled, using its corresponding control bit in the PIEx registers, can wake-up the processor from Sleep mode. When the device wakes from Sleep mode, one of two following actions may occur: • If the GIE bit is set, the processor will wake and the Program Counter will begin execution at the interrupt vector. • If the GIE bit is not set, the processor will wake and the Program Counter will continue execution following the SLEEP instruction that initiated Sleep mode. 4.3.3 WAKE-UP FROM SLEEP ON RESET All sources of device Reset will wake-up the processor from Sleep mode.  2012-2016 Microchip Technology Inc. DS30000575C-page 73 PIC18F97J94 FAMILY TABLE 4-3: DELAY TIMES FOR EXITING FROM SLEEP MODE Clock Source Exit Delay Oscillator Delay Notes EC TPM — ECPLL TPM TLOCK 1, 3 1, 2 1 MS, HS TPM TOST MSPLL, HSPLL TPM TOST + TLOCK SOSC (Off during Sleep) TPM TOST (On during Sleep) TPM — TPM TFRC 1, 4 (Off during Sleep) TPM TLPRC 1, 4 (On during Sleep) TPM — TPM TLOCK FRC, FRCDIV LPRC FRCPLL Note 1: 2: 3: 4: 1, 2, 3 1, 2 1 1 1, 3 TPM = Start-up delay for program memory stabilization. TOST = Oscillator Start-up Timer (OST); a delay of 1024 oscillator periods before the oscillator clock is released to the system. TLOCK = PLL lock time. TFRC and TLPRC are RC Oscillator start-up times. TABLE 4-4: DELAY TIMES FOR EXITING FROM RETENTION SLEEP MODE Clock Source Exit Delay Oscillator Delay EC TRETR + TPM — ECPLL TRETR + TPM TLOCK 1, 2, 4 MS, HS TRETR + TPM TOST 1, 2, 3 MSPLL, HSPLL TRETR + TPM TOST + TLOCK SOSC (Off during Sleep) TRETR + TPM TOST (On during Sleep) TRETR FRC, FRCDIV LPRC 4: 5: — 1, 2 1, 2, 3, 4 1, 2, 3 1, 2 TRETR + TPM TFRC 1, 2, 5 (Off during Sleep) TRETR + TPM TLPRC 1, 2, 5 (On during Sleep) TRETR + TPM — TRETR + TPM TLOCK FRCPLL Note 1: 2: 3: + TPM Notes 1, 2 1, 2, 4 TRETR = Retention regulator start-up delay. TPM = Start-up delay for program memory stabilization; applicable only when IPEN (RCON) = 0. TOST = Oscillator Start-up Timer; a delay of 1024 oscillator periods before the oscillator clock is released to the system. TLOCK = PLL lock time. TFRC and TLPRC are RC Oscillator start-up times. DS30000575C-page 74  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 4.4 Deep Sleep Modes The Deep Sleep modes puts the device into its lowest power consumption states without requiring the use of external switches to remove power from the device. There are two modes available: Deep Sleep mode and Retention Deep Sleep mode. During both Deep Sleep modes, the power to the microcontroller core is removed to reduce leakage current. Therefore, most peripherals and functions of the microcontroller become unavailable during Deep Sleep. However, a few specific peripherals and functions are powered directly from the VDD supply rail of the microcontroller, and therefore, can continue to function in Deep Sleep. In addition, four data memory locations, DSGPR0, DSGPR1, DSGPR2 and DSGPR3, are preserved for context information after an exit from Deep Sleep. Deep Sleep has a dedicated Deep Sleep Brown-out Reset (DSBOR) and a Deep Sleep Watchdog Timer Reset (DSWDT) for monitoring voltage and time-out events in Deep Sleep mode. The DSBOR and DSWDT are independent of the standard BOR and WDT used with other power-managed modes (Run, Idle and Sleep). Entering Deep Sleep mode clears the Deep Sleep Wake-up Source Registers (DSWAKEL and DSWAKEH). If enabled, the Real-Time Clock and Calendar (RTCC) continues to operate uninterrupted. When a wake-up event occurs in Deep Sleep mode (by Reset, RTCC alarm, External Interrupt (INT0) or DSWDT), the device will exit Deep Sleep mode and rearm a Power-on Reset (POR). When the device is released from Reset, code execution will resume at the Reset vector. 4.4.1 RETENTION DEEP SLEEP MODE In Retention Deep Sleep, the retention regulator is enabled, which allows the data RAM to retain data while all other systems are powered down. This also allows the device to return to code execution where it left off, instead of going through a POR-like Reset. As a trade-off, Retention Deep Sleep mode has greater power consumption than Deep Sleep. However, it offers the lowest level of power consumption of the power-saving modes that still allows a direct return to code execution. Retention Deep Sleep is controlled by the SRETEN bit (RCON4) and the RETEN Configuration bit, as described in Section 4.2.2 “Retention Regulator”.  2012-2016 Microchip Technology Inc. 4.4.2 ENTERING DEEP SLEEP MODES Deep Sleep modes are entered by: • Setting the DSEN bit (DSCONH) • Executing the SLEEP instruction To enter Retention Deep Sleep, the SRETEN bit must also be set prior to setting the DSEN bit (Example 4-1). In order to minimize the possibility of inadvertently entering Deep Sleep, the DSEN bit must be set by two separate write operations. To enter Deep Sleep, the SLEEP instruction must be executed after setting the DSEN bit (i.e., the next instruction). If DSEN is not set when Sleep is executed, the device will enter a Sleep mode instead. 4.4.3 DEEP SLEEP WAKE-UP SOURCES The device can be awakened from Deep Sleep modes by any of the following: • • • • • MCLR POR RTCC Alarm INT0 Interrupt DSWDT Event After waking from Deep Sleep mode, the device performs a POR. When the device is released from Reset, code execution will begin at the device’s Reset vector. The software can determine if the wake-up was caused from an exit from Deep Sleep mode by reading the DPSLP bit (RCON4). If this bit is set, the POR was caused by a Deep Sleep exit. The DPSLP bit must be manually cleared by the software. The software can determine the wake-up event source by reading the DSWAKE registers. These registers are cleared automatically when entering Deep Sleep mode, so software should read these registers after exiting Deep Sleep mode or before re-enabling this mode. 4.4.4 CLOCK SELECTION ON WAKE-UP FROM DEEP SLEEP MODE For Deep Sleep mode, the processor will restart with the default oscillator source, selected with the FOSCx Configuration bits. On wake-up from Deep Sleep, a POR is generated internally, hence, the system resets to its POR state with the exception of the RCONx, DSCONH/L and DSGPRx registers. For Retention Deep Sleep, the processor restarts with the same clock source that was selected before entering Retention Deep Sleep mode. Wake-up is similar to that of Sleep and Retention Sleep modes. DS30000575C-page 75 PIC18F97J94 FAMILY 4.4.5 SAVING CONTEXT DATA WITH THE DSGPRx REGISTERS As exiting Deep Sleep mode causes a POR, most Special Function Registers (SFRs) reset to their default POR values. In addition, because the core power is not supplied in Deep Sleep mode, information in data RAM may be lost when exiting this mode. Applications which require critical data to be saved prior to Deep Sleep may use the Deep Sleep General Purpose registers, DSGPR0, DSGPR1, DSGPR2 and DSGPR3. Unlike other SFRs, the contents of these registers are preserved while the device is in Deep Sleep mode. After exiting Deep Sleep, software can restore the data by reading the registers and clearing the RELEASE bit (DSCONL). Any data stored in the DSGPRx registers must be written twice. Like other Deep Sleep control features, the write operations do not need to be sequential. However, back-to-back writes are a recommended programming practice. Since the contents of data RAM are maintained in Retention Deep Sleep, the use of the DSGPRx registers to store critical data is not necessary in this mode. 4.4.6 I/O PINS DURING DEEP SLEEP During Deep Sleep, general purpose I/O pins retain their previous states. Pins that are configured as inputs (TRIS bit is set), prior to entry into Deep Sleep, remain high-impedance during Deep Sleep. Pins that are configured as outputs (TRIS bit is clear), prior to entry into Deep Sleep, will remain as output pins during Deep Sleep. While in this mode, they will drive the output level determined by their corresponding LAT bit at the time of entry into Deep Sleep. Once the device wakes back up, all I/O pins will continue to maintain their previous states, even after the device has finished the POR sequence and is executing application code again. Pins configured as inputs during Deep Sleep will remain high-impedance and pins configured as outputs will continue to drive their previous value. After waking up, the TRIS and LAT registers will be reset. If firmware modifies the TRIS and LAT values for the I/O pins, they will not immediately go to the newly configured states. Once the firmware clears the RELEASE bit (DSCONL), the I/O pins are “released”. This causes the I/O pins to take the states configured by their respective TRIS and LAT bit values. If the Deep Sleep BOR (DSBOR) is enabled, and a DSBOR event occurs during Deep Sleep (or VDD is hard-cycled to VSS), the I/O pins will be immediately released, similar to clearing the RELEASE bit. All previous state information will be lost, including the general purpose DSGPR0, DSGPR1, DSGPR2 and DSGPR3 contents. DSGPRx register contents will be maintained if the VBAT pin is powered. DS30000575C-page 76 If a MCLR Reset event occurs during Deep Sleep, the I/O pins will also be released automatically, but in this case, the DSGPR0, DSGPR1, DSGPR2 and DSGPR3 contents will remain valid. In case of MCLR Reset and all other Deep Sleep wakeup cases, application firmware needs to clear the RELEASE bit (DSCONL) in order to reconfigure the I/ O pins. 4.4.7 DEEP SLEEP WATCHDOG TIMER (DSWDT) Deep Sleep has its dedicated WDT (DSWDT). It is enabled through the DSWDTEN Configuration bit. The DSWDT is equipped with a postscaler for time-outs of 2.1 ms to 25.7 days, configurable through the Configuration bits, DSWDTPS. Entering Deep Sleep mode automatically clears the DSWDT. The DSWDT also has a configurable reference clock source for selecting the LPRC or SOSC. The reference clock source is configured through the DSWDTOSC Configuration bit. Under certain circumstances, it is possible for the DSWDT clock source to be off when entering Deep Sleep mode. In this case, the clock source is turned on automatically (if DSWDT is enabled), without the need for software intervention. However, this can cause a delay in the start of the DSWDT counters. In order to avoid this delay, when using SOSC as a clock source, the application can activate SOSC prior to entering Deep Sleep mode. 4.4.8 DEEP SLEEP LOW-POWER BROWN-OUT RESET Devices with a Deep Sleep Power-Saving mode also have a dedicated BOR for Deep Sleep modes (DSBOR). It has a trip point range of 1.7V-2.3V nominal and is enabled through the DSBOREN (CONFIG7L) Configuration bit. When the device enters a Deep Sleep mode and receives a DSBOR event, the device will not wake-up and will remain in the Deep Sleep mode. When a valid wake-up event occurs and causes the device to exit Deep Sleep mode, software can determine if a DSBOR event occurred during Deep Sleep mode by reading the BOR (DSWAKEL) Status bit. 4.4.9 RTCC AND DEEP SLEEP The RTCC can operate uninterrupted during Deep Sleep modes. It can wake-up the device from Deep Sleep by configuring an alarm. The RTCC clock source is configured with the RTCC Clock Select bits, RTCCLKSEL. The available reference clock sources are the LPRC and SOSC. If the LPRC is used, the RTCC accuracy will directly depend on the LPRC tolerance. If the RTCC is not required, Deep Sleep mode with the RTCC disabled, affords the lowest power consumption of any of the instruction-based power-saving modes.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 4.4.10 CONTROL BIT SUMMARY FOR SLEEP MODES Table 4-5 shows the settings for the bits relevant to Deep Sleep modes. TABLE 4-5: BIT SETTINGS FOR ALL DEEP SLEEP MODES Instruction-Based Mode DSEN (DSCONH) Retention Deep Sleep Deep Sleep 4.4.11 Retention Regulator RETEN (CONFIG7L) SRETEN (RCON4) State DSWDTEN (CONFIG8H) 1 0 1 Enabled 0 1 1 x Disabled x WAKE-UP DELAYS Note: The Reset delays associated with wake-up from Deep Sleep and Retention Deep Sleep modes, in different oscillator modes, are provided in Table 4-6 and Table 4-7, respectively. TABLE 4-6: The PMSLP bit (RCON4) allows the voltage regulator to be maintained during Sleep modes. DELAY TIMES FOR EXITING FROM DEEP SLEEP MODE Clock Source Exit Delay Oscillator Delay Notes EC TDSWU — ECPLL TDSWU TLOCK 1, 3 1, 2 MS, HS TDSWU TOST MSPLL, HSPLL TDSWU TOST + TLOCK SOSC (Off during Sleep) TDSWU TOST (On during Sleep) TDSWU — TDSWU TFRC 1, 4 (Off during Sleep) TDSWU TLPRC 1, 4 (On during Sleep) TDSWU — TDSWU TFRC + TLOCK FRC, FRCDIV LPRC FRCPLL Note 1: 2: 3: 4: 1, 2, 3 1, 2 1 1 1, 3, 4 TDSWU = Deep Sleep wake-up delay. TOST = Oscillator Start-up Timer; a delay of 1024 oscillator periods before the oscillator clock is released to the system. TLOCK = PLL lock time. TFRC and TLPRC are RC Oscillator start-up times.  2012-2016 Microchip Technology Inc. DS30000575C-page 77 PIC18F97J94 FAMILY TABLE 4-7: DELAY TIMES FOR EXITING RETENTION DEEP SLEEP MODE Clock Source Exit Delay Oscillator Delay EC TRETR + TPM — ECPLL TRETR + TPM TLOCK 1, 2, 4, 6 MS, HS TRETR + TPM TOST 1, 2, 3, 6 MSPLL, HSPLL TRETR + TPM TOST + TLOCK Off during Sleep TRETR + TPM TOST On during Sleep TRETR + TPM — SOSC 4: 5: 6: 1, 2, 3, 4, 6 1, 2, 3, 6 1, 2, 6 TFRC 1, 2, 5, 6 Off during Sleep TRETR + TPM TLPRC 1, 2, 5, 6 On during Sleep TRETR + TPM — TRETR + TPM TLOCK TRETR FRCPLL Note 1: 2: 3: 1, 2, 6 + TPM FRC, FRCDIV LPRC: Notes 1, 2, 6 1, 2, 3, 6 TPM = Start-up delay for program memory stabilization; applicable only when IPEN (RCON) = 0. TRETR = Retention regulator start-up delay. TOST = Oscillator Start-up Timer (OST); a delay of 1024 oscillator periods before the oscillator clock is released to the system. TLOCK = PLL lock time. TFRC and TLPRC = RC Oscillator start-up times. TFLASH = Flash program memory ready delay. Setting the PMSLP bit will provide a faster wake-up. DS30000575C-page 78  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 4.5 VBAT Mode Entering VBAT mode requires that a power source, distinct from the main VDD power source, be available on VBAT and that VDD be completely removed from the VDD pin(s). Removing VDD can be either unintentional, as in a power failure, or as part of a deliberate power reduction strategy. VBAT mode is a hardware-based power mode that maintains only the most critical operations when a power loss occurs on VDD. The mode does this by powering these systems from a back-up power source connected to the VBAT pin. In this mode, the RTCC can run even when there is no power on VDD. As with Deep Sleep modes, the contents of the Deep Sleep General Purpose (DSGPRx) registers are maintained by the retention regulator. Since the power loss on VDD may be unforeseen, it is recommended to load any data to be saved in these registers in advance. VBAT mode is entered whenever power is removed from VDD. An on-chip power switch detects the power loss from the VDD and connects the VBAT pin to the retention regulator. This provides power at 1.2V to maintain the retention regulator, as well as the RTCC, with its clock source (if enabled) and the Deep Sleep General Purpose (DSGPRx) registers (Figure 4-1). FIGURE 4-1: Any data stored in the DSGPRx registers must be written twice. The write operations do not need to be sequential; however, back-to-back writes are a recommended programming practice. VBAT POWER TOPOLOGY PIC18F97J94 Family Microcontroller Core VBAT Back-up Battery VDD Power Switch Retention Regulator 1.2V DSGPRx Registers Peripherals VSS RTCC  2012-2016 Microchip Technology Inc. DS30000575C-page 79 PIC18F97J94 FAMILY 4.5.1 WAKE-UP FROM VBAT MODES When VDD is restored to a device in VBAT mode, it automatically wakes. Wake-up occurs with a POR, after which the device starts executing code from the Reset vector. All SFRs, except the Deep Sleep semaphores and RTCC registers are reset to their POR values. If the RTCC was not configured to run during VBAT mode, it will remain disabled and RTCC will not run. Wake-up timing is similar to that for a normal POR. Wake-up from VBAT mode is identified by checking the state of the VBAT bit (RCON3). If this bit is set when the device is awake and starting to execute the code from the Reset vector, it indicates that the exit was from VBAT mode. To identify future VBAT wake-up events, the bit must be cleared in software. When a POR event occurs with no battery connected to the VBAT pin, the VBPOR bit (RCON3) becomes set. On the device, if there is no battery connected to the VBAT pin, VBPOR will indicate that the battery needs to be connected to the VBAT pin. In addition, if the VBAT power source falls below the level needed for Deep Sleep semaphore operation while in VBAT mode (e.g., the battery has been drained), the VBPOR bit will be set. VBPOR is also set when the microcontroller is powered up the very first time, even if power is supplied to VBAT. DS30000575C-page 80 4.6 Saving Context Data with the DSGPRx Registers As exiting VBAT causes a POR, most Special Function Registers reset to their default POR values. In addition, because the core power is not supplied in VBAT mode, information in data RAM will be lost when exiting this mode. Applications which require critical data to be saved, should be saved in DSGPR0, DSGPR1, DSGPR2 and DSGPR3. Any data stored to the DSGPRx registers must be written twice. The write operations do not need to be sequential. However, back-to-back writes are a recommended programming practice. After exiting VBAT mode, software can restore the data by reading the registers. 4.6.1 I/O PINS DURING VBAT MODE All I/O pins should be maintained at VSS level; no I/O pins should be given VDD (refer to “Absolute Maximum Ratings(†)” in Section 30.0 “Electrical Specifications”) during VBAT mode. The only exceptions are the SOSCI and SOSCO pins, which maintain their states if the Secondary Oscillator is being used as the RTCC clock source. It is the user’s responsibility to restore the I/O pins to their proper states, using the TRIS and LAT bits, once VDD has been restored.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 4-1: DSCONL: DEEP SLEEP CONTROL REGISTER LOW U-0 U-0 U-0 U-0 U-0 R-0 R/W-0, HSC R/W-0, HS — — — — — r DSBOR(1) RELEASE(1) bit 7 bit 0 Legend: r = Reserved bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown HS = Hardware Settable bit bit 7-3 Unimplemented: Read as ‘0’ bit 2 Reserved: Maintained as ‘0’ bit 1 DSBOR: Deep Sleep BOR Event Status bit(1) 1 = DSBOR was enabled and VDD dropped below the DSBOR threshold during Deep Sleep(2) 0 = DSBOR disabled while device is in Deep Sleep mode bit 0 RELEASE: I/O Pin State Release bit(1) Upon waking from Deep Sleep, the I/O pins maintain their previous states. Clearing this bit will release the I/O pins and allow their respective TRIS and LAT bits to control their states. Note 1: 2: This is the value when VDD is initially applied. Unlike all other events, a Deep Sleep BOR event will not cause a wake-up from Deep Sleep; this bit is present only as a Status bit. REGISTER 4-2: DSCONH: DEEP SLEEP CONTROL REGISTER HIGH R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0, HS(2) DSEN(1) — — — — — — RTCCWDIS bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 DSEN: Deep Sleep Mode Enable bit(1) 1 = Deep Sleep mode is enabled and device will enter Deep Sleep mode when the SLEEP instruction is executed 0 = Deep Sleep mode is not enabled bit 6-1 Unimplemented: Read as ‘0’ bit 0 RTCCWDIS: RTCC Wake-up Disable bit(2) 1 = Wake-up from RTCC is disabled 0 = Wake-up from RTCC is enabled Note 1: 2: In order to enter Deep Sleep, DSEN must be written to in two separate operations. The write operations do not need to be consecutive. Before writing DSEN, the DSCON1 register should be cleared twice. This is the value when VDD is initially applied.  2012-2016 Microchip Technology Inc. DS30000575C-page 81 PIC18F97J94 FAMILY DSWAKEL: DEEP SLEEP WAKE-UP SOURCE REGISTER LOW(1) REGISTER 4-3: R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DSFLT BOR EXT DSWDT DSRTC MCLR ICD DSPOR bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 DSFLT: Deep Sleep Fault Detect bit 1 = A Deep Sleep Fault was detected during Deep Sleep 0 = A Deep Sleep Fault was not detected during Deep Sleep bit 6 BOR: BOR Deep-Sleep Wake-up Source Enable bit 1 = DSBOR event will wake device from Deep Sleep 0 = DSBOR event will not wake device from Deep Sleep bit 5 EXT: External Interrupt Wake-up Source Enable bit 1 = External interrupt will wake device from Deep Sleep 0 = External interrupt will not wake device from Deep Sleep bit 4 DSWDT: DSWDT Deep-Sleep Wake-up Source Enable bit 1 = DSWDT roll-over event will wake device from Deep Sleep 0 = DSWDT roll-over event will not wake device from Deep Sleep bit 3 DSRTC: Real-Time Clock and Calendar Alarm bit 1 = The Real-Time Clock/Calendar triggered an alarm during Deep Sleep 0 = The Real-Time Clock /Calendar did not trigger an alarm during Deep Sleep bit 2 MCLR: MCLR Deep-Sleep Wake-up Source Enable bit 1 = The MCLR Reset will wake device from Deep Sleep 0 = The MCLR Reset will not wake device from Deep Sleep bit 1 ICD: In-Circuit Debugger Deep-Sleep Wake-up Source Enable bit 1 = In-Circuit Debugger will wake device from Deep Sleep 0 = In-Circuit Debugger will not wake device from Deep Sleep bit 0 DSPOR: Power-on Reset Event bit 1 = The VDD supply POR circuit was active and a POR event was detected 0 = The VDD supply POR circuit was not active, or was active but did not detect a POR event Note 1: To be set in software, all bits in DSWAKE must be written to twice. The write operations do not need to be consecutive. REGISTER 4-4: DSWAKEH: DEEP SLEEP WAKE-UP SOURCE REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — INT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-1 Unimplemented: Read as ‘0’ bit 0 INT0: Deep Sleep Wake-up Source Enable bit 1 = INT0 interrupt will wake device from Deep Sleep 0 = INT0 interrupt will not wake device from Deep Sleep DS30000575C-page 82 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 4.7 Selective Peripheral Power Control Sleep and Idle modes allow users to substantially reduce power consumption by slowing or stopping the CPU clock. Even so, peripheral modules still remain clocked, and thus, consume some amount of power. There may be cases where the application needs what these modes do not provide: the ability to allocate limited power resources to the CPU while eliminating power consumption from the peripherals. The 08KA101 family addresses this requirement by allowing peripheral modules to be selectively enabled or disabled, reducing or eliminating their power consumption. 4.7.1 DISABLING PERIPHERAL MODULES Most of the peripheral modules in the 08KA101 family architecture can be selectively disabled, reducing, or essentially eliminating, their power consumption during all operating modes. Two different options are available to users, each with a slightly different effect. 4.7.2 MODULE ENABLE BIT (XXXEN) Many peripheral modules have a Module Enable bit, generically named, “XXXEN”, usually located in Bit Position 7 of their control registers (or Primary Control registers for more complex modules). Here, “XXX” represents the mnemonic form for the module of the module name. For example, the enable bit for an MSSPx module is “SSPEN”, and so on. The bit is provided for all serial and parallel communication modules and the Real-Time Clock (RTC). Clearing this bit disables the module’s operation; however, it continues to receive clock signals and draw a minimal amount of current. Disabling modules not required for a particular application, in this manner, allows for the selective and dynamic adjusting power consumption, under software control, as the application is running. 4.7.3 PERIPHERAL MODULE DISABLE BIT (XXMD) All peripheral modules (except for I/O ports) also have a second control bit that can disable their functionality. These bits, known as the Peripheral Module Disable (PMD) bits, are generically named, “XXMD” (using “XX” as the mnemonic version of the module’s name), as shown in Section 4.7.2 “Module Enable Bit (XXXEN)”). These bits are located in the PMDx SFRs. In contrast to the module enable bits, the XXMD bit must be set (= 1) to disable the module. While the PMD and module enable bits both disable a peripheral’s functionality, the PMD bit completely shuts down the peripheral, effectively powering down all circuits and removing all clock sources. This has the additional effect of making any of the module’s control and buffer registers, mapped in the SFR space, unavailable for operations. In other words, when the PMD bit is used to disable a module, the peripheral ceases to exist until the PMD bit is cleared. This differs from using the module enable bit, which allows the peripheral to be reconfigured and buffer registers preloaded, even when the peripheral’s operations are disabled. The PMD bit is most useful in highly power-sensitive applications, where even tiny savings in power consumption can determine the ability of an application to function. In these cases, the bits can be set before the main body of the application to remove those peripherals that will not be needed at all. As with all earlier PIC® MCU devices, timers continue to be under selective operation and are controlled by their own TON bit, also located in Position 7. The A/D Converter also has a legacy enable bit, ADON, that has the same function as the XXXEN bits. I/O ports and features associated with them, such as input change notification and input capture, do not have their own module enable bits, since their operation is secondary to other modules.  2012-2016 Microchip Technology Inc. DS30000575C-page 83 PIC18F97J94 FAMILY REGISTER 4-5: PMD0: PERIPHERAL MODULE DISABLE REGISTER 0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CCP10MD CCP9MD CCP8MD CCP7MD CCP6MD CCP5MD CCP4MD ECCP3MD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 CCP10MD: CCP10 Module Disable bit 1 = The CCP10 module is disabled. All CCP10 registers are held in Reset and are not writable. 0 = The CCP10 module is enable bit 6 CCP9MD: CCP9 Module Disable bit 1 = The CCP9 module is disabled. All CCP9 registers are held in Reset and are not writable. 0 = The CCP9 module is enabled bit 5 CCP8MD: CCP8 Module Disable bit 1 = The CCP8 module is disabled. All CCP8 registers are held in Reset and are not writable. 0 = The CCP8 module is enabled bit 4 CCP7MD: CCP7 Module Disable bit 1 = The CCP7 module is disabled. All CCP7 registers are held in Reset and are not writable. 0 = The CCP7 module is enabled bit 3 CCP6MD: CCP6 Module Disable bit 1 = The CCP6 module is disabled. All CCP6 registers are held in Reset and are not writable. 0 = The CCP6 module is enabled bit 2 CCP5MD: CCP5 Module Disable bit 1 = The CCP5 module is disabled. All CCP5 registers are held in Reset and are not writable. 0 = The CCP5 module is enabled bit 1 CCP4MD: CCP4 Module Disable bit 1 = The CCP4 module is disabled. All CCP4 registers are held in Reset and are not writable. 0 = The CCP4 module is enabled bit 0 ECCP3MD: ECCP3 Module Disable bit 1 = The ECCP3 module is disabled. All ECCP3 registers are held in Reset and are not writable. 0 = The ECCP3 module is enabled DS30000575C-page 84  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 4-6: PMD1: PERIPHERAL MODULE DISABLE REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCP2MD ECCP1MD UART4MD UART3MD UART2MD UART1MD SSP2MD SSP1MD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 ECCP2MD: ECCP2 Module Disable bit 1 = The ECCP2 module is disabled. All ECCP2 registers are held in Reset and are not writable. 0 = The ECCP2 module is enabled bit 6 ECCP1MD: ECCP1 Module Disable bit 1 = The ECCP1 module is disabled. All ECCP1 registers are held in Reset and are not writable. 0 = The ECCP1 module is enabled bit 5 UART4MD: USART4 Module Disable bit 1 = The USART4 module is disabled. All USART4 registers are held in Reset and are not writable. 0 = The USART4 module is enabled bit 4 UART3MD: USART3 Module Disable bit 1 = The USART3 module is disabled. All USART3 registers are held in Reset and are not writable. 0 = The USART3 module is enabled bit 3 UART2MD: USART2 Module Disable bit 1 = The USART2 module is disabled. All USART2 registers are held in Reset and are not writable. 0 = The USART2 module is enabled bit 2 UART1MD: USART1 Module Disable bit 1 = The USART1 module is disabled. All USART1 registers are held in Reset and are not writable. 0 = The USART1 module is enabled bit 1 SSP2MD: SSP2 Module Disable bit 1 = The SSP2 module is disabled. All SSP2 registers are held in Reset and are not writable. 0 = The SSP2 module is enabled bit 0 SSP1MD: SSP1 Module Disable bit 1 = The SSP1 module is disabled. All SSP1 registers are held in Reset and are not writable. 0 = The SSP1 module is enabled  2012-2016 Microchip Technology Inc. DS30000575C-page 85 PIC18F97J94 FAMILY REGISTER 4-7: PMD2: PERIPHERAL MODULE DISABLE REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TMR8MD TMR6MD TMR5MD TMR4MD TMR3MD TMR2MD TMR1MD TMR0MD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 TMR8MD: Timer8 Module Disable bit 1 = The Timer8 module is disabled. All Timer8 registers are held in Reset and are not writable. 0 = The Timer8 module is enabled bit 6 TMR6MD: Timer6 Module Disable bit 1 = The Timer6 module is disabled. All Timer6 registers are held in Reset and are not writable. 0 = The Timer6 module is enabled bit 5 TMR5MD: Timer5 Module Disable bit 1 = The Timer5 module is disabled. All Timer5 registers are held in Reset and are not writable. 0 = The Timer5 module is enabled bit 4 TMR4MD: Timer4 Module Disable bit 1 = The Timer4 module is disabled. All Timer4 registers are held in Reset and are not writable. 0 = The Timer4 module is enabled bit 3 TMR3MD: Timer3 Module Disable bit 1 = The Timer3 module is disabled. All Timer3 registers are held in Reset and are not writable. 0 = The Timer3 module is enabled bit 2 TMR2MD: Timer2 Module Disable bit 1 = The Timer2 module is disabled. All Timer2 registers are held in Reset and are not writable. 0 = The Timer2 module is enabled bit 1 TMR1MD: Timer1 Module Disable bit 1 = The Timer1 module is disabled. All Timer1 registers are held in Reset and are not writable. 0 = The Timer1 module is enabled bit 0 TMR0MD: Timer0 Module Disable bit 1 = The Timer0 module is disabled. All Timer0 registers are held in Reset and are not writable. 0 = The Timer0 module is enabled DS30000575C-page 86  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 4-8: PMD3: PERIPHERAL MODULE DISABLE REGISTER 3 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DSMMD CTMUMD ADCMD RTCCMD LCDMD PSPMD REFO1MD REFO2MD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 x = Bit is unknown DSMMD: Modulator Output Module Disable bit 1 = The Modulator Output module is disabled. All Modulator Output registers are held in Reset and are not writable. 0 = The Modulator Output module is enabled bit 6 CTMUMD: CTMU Module Disable bit 1 =The CTMU module is disabled. All CTMU registers are held in Reset and are not writable. 0 =The CTMU module is enabled bit 5 ADCMD: ADC Module Disable bit 1 =The ADC module is disabled. All ADC registers are held in Reset and are not writable. 0 =The ADC module is enabled bit 4 RTCCMD: RTCC Module Disable bit 1 = The RTCC module is disabled. All RTCC registers are held in Reset and are not writable. 0 = The RTCC module is enabled bit 3 LCDMD: LCD Module Disable bit 1 = The LCD module is disabled. All LCD registers are held in Reset and are not writable. 0 = The LCD module is enabled bit 2 PSPMD: PSP Module Disable bit 1 = The PSP module is disabled. All PSP registers are held in Reset and not are writable. 0 = The PSP module is enabled bit 1 REFO1MD: REFO1 Module Disable bit 1 = The REFO1 module is disabled. All REFO1 registers are held in Reset and are not writable. 0 = The REFO1 module is enabled bit 0 REFO2MD: REFO2 Module Disable bit 1 = The REFO2 module is disabled. All REFO2 registers are held in Reset and are not writable. 0 = The REFO2 module is enabled  2012-2016 Microchip Technology Inc. DS30000575C-page 87 PIC18F97J94 FAMILY REGISTER 4-9: PMD4: PERIPHERAL MODULE DISABLE REGISTER 4 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 CMP1MD CMP2MD CMP3MD USBMD IOCMD LVDMD — EMBMD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 CMP1MD: CMP1 Module Disable bit 1 = The CMP1 module is disabled; all CMP1 registers are held in Reset and are not writable 0 = The CMP1 module is enabled bit 6 CMP2MD: CMP2 Module Disable bit 1 = The CMP2 module is disabled; all CMP2 registers are held in Reset and are not writable 0 = The CMP2 module is enabled bit 5 CMP3MD: CMP3 Module Disable bit 1 = The CMP3 module is disabled; all CMP3 registers are held in Reset and are not writable 0 = The CMP3 module is enabled bit 4 USBMD: USB Module Disable bit 1 = The USB module is disabled; all USB registers are held in Reset and are not writable 0 = The USB module is enabled bit 3 IOCMD: Interrupt-on-Change Module Disable bit 1 = The IOC module is disabled; all IOC registers are held in Reset and are not writable 0 = The IOC module is enabled bit 2 LVDMD: Low Voltage Detect Module Disable bit 1 = The LVD module is disabled; all LVD registers are held in Reset and are not writable 0 = The LVD module is enabled bit 1 Unimplemented: Read as ‘0’ bit 0 EMBMD: EMB Module Disable bit 1 = The EMB module is disabled; all EMB registers are held in Reset and are not writable 0 = The EMB module is enabled DS30000575C-page 88  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 5.0 RESET The 08KA101 family devices differentiate between various kinds of Reset: a) b) c) d) e) f) g) Power-on Reset (POR) MCLR Reset Watchdog Timer (WDT) Reset Configuration Mismatch (CM) Brown-out Reset (BOR) RESET Instruction Stack Underflow/Overflow Reset This section discusses Resets generated by MCLR, POR and BOR, and covers the operation of the various start-up timers. For information on WDT Resets, see Section 28.2 “Watchdog Timer (WDT)”. For Stack Reset events, see Section 6.1.4.4 “Stack Full and Underflow Resets”. For Deep Sleep mode, see Section 4.4 “Deep Sleep Modes”. FIGURE 5-1: A simplified block diagram of the On-Chip Reset Circuit is shown in Figure 5-1. 5.1 RCON Registers Device Reset events are tracked through the RCON, RCON2, RCON3 and RCON4 registers (Register 5-1, Register 5-2, Register 5-3 and Register 5-4). The register bits indicate that a specific Reset event has occurred. Depending on the definition, Status bits may be set or cleared by the event, and re-initialized by the application, after the event to the opposite state. Setting or clearing Reset Status bits does not cause a Reset. The state of these flag bits, taken together, can be read to indicate the type of Reset that just occurred. The RCON register also has a control bit for setting interrupt priority (IPEN). Interrupt priority is discussed in Section 10.0 “Interrupts”. SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT RESET Instruction Stack Full/Underflow Reset Stack Pointer External Reset MCLR MCLRE Idle Sleep WDT Time-out VDD Rise POR Pulse Detect VDD Brown-out Reset BOREN S OST/PWRT OST 1024 Cycles 10-Bit Ripple Counter OSC1 32 s INTOSC(1) PWRT R Q Internal Reset 1 ms 11-Bit Ripple Counter Enable PWRT Enable OST(2) Note 1: 2: This is the INTOSC source from the internal oscillator block and is separate from the RC Oscillator of the CLKI pin. See Table 5-1 for time-out situations.  2012-2016 Microchip Technology Inc. DS30000575C-page 89 PIC18F97J94 FAMILY REGISTER 5-1: RCON: RESET CONTROL REGISTER R/W-0 U-0 R/W-1 R/W-1 R-1 R-1 R/W-0(1) R/W-0 IPEN — CM RI TO PD POR BOR bit 7 bit 0 Legend: HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 IPEN: Interrupt Priority Enable Register bit 1 = Prioritized interrupts are enabled 0 = Prioritized interrupts are disabled bit 6 Unimplemented: Read as ‘0’ bit 5 CM: Configuration Mismatch Flag bit 1 = A Configuration Mismatch Reset has not occurred 0 = A Configuration Mismatch Reset occurred; must be set in software once the Reset occurs bit 4 RI: RESET Instruction Flag bit 1 = The RESET instruction was not executed (set by firmware only) 0 = The RESET instruction was executed, causing a device Reset (must be set in software after a Brown-out Reset occurs) bit 3 TO: Watchdog Time-out Flag bit 1 = Set by power-up, CLRWDT instruction or SLEEP instruction 0 = A WDT time-out occurred bit 2 PD: Power-down Detection Flag bit 1 = Set by power-up or by the CLRWDT instruction 0 = Set by execution of the SLEEP instruction bit 1 POR: Power-on Reset Status bit(1) 1 = A Power-on Reset has not occurred (set by firmware only) 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) bit 0 BOR: Brown-out Reset Status bit 1 = A Brown-out Reset has not occurred (set by firmware only) 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs) Note 1: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming that POR was set to ‘1’ by software immediately after a Power-on Reset). DS30000575C-page 90  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 5-2: R/W-0, HS RCON2: RESET CONTROL REGISTER 2 U-0 (1) EXTR — R/W-0 (2) SWDTEN U-0 U-0 U-0 U-0 U-0 — — — — — bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 EXTR: External Reset (MCLR) Pin bit(1) 1 = A Master Clear (pin) Reset has occurred 0 = A Master Clear (pin) Reset has not occurred bit 6 Unimplemented: Read as ‘0’ bit 5 SWDTEN: Software Controlled Watchdog Timer Enable bit(2) 1 = Watchdog Timer is on 0 = Watchdog Timer is off bit 4-0 Unimplemented: Read as ‘0’ Note 1: 2: x = Bit is unknown This bit is set in hardware; it can be cleared in software. This bit has no effect unless the Configuration bits, WDTEN = 10.  2012-2016 Microchip Technology Inc. DS30000575C-page 91 PIC18F97J94 FAMILY REGISTER 5-3: U-0 RCON3: RESET CONTROL REGISTER 3 U-0 — — U-0 — U-0 — R/C-0 R/C-0 (1) VDDBOR VDDPOR R/C-0 (1,2) (1,3) VBPOR R/W-0 VBAT bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-4 Unimplemented: Read as ‘0’ bit 3 VDDBOR: VDD Brown-out Reset Flag bit(1) 1 = A VDD Brown-out Reset has occurred 0 = A VDD Brown-out Reset has not occurred bit 2 VDDPOR: VDD Power-On Reset Flag bit(1,2) 1 = A VDD Power-up Reset has occurred 0 = A VDD Power-up Reset has not occurred bit 1 VBPOR: VBPOR Flag bit(1,3) 1 = A VBAT POR has occurred 0 = A VBAT POR has not occurred bit 0 VBAT: VBAT Flag bit(1) 1 = A POR exit has occurred while power was applied to VBAT pin 0 = A POR exit from VBAT has not occurred Note 1: 2: 3: This bit is set in hardware only; it can only be cleared in software. Indicates a VDD POR. Setting the POR bit (RCON) indicates a VCORE POR. This bit is set when the device is originally powered up, even if power is present on VBAT. DS30000575C-page 92  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 5-4: RCON4: RESET CONTROL REGISTER 4 U-0 U-0 U-0 R/W-0 U-0 R/C-0 U-0 R/W-0 — — — SRETEN(1) — DPSLP(2) — PMSLP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-5 Unimplemented: Read as ‘0’ bit 4 SRETEN: Retention Regulator Voltage Sleep Disable bit(1) 1 = If RETEN (CONFIG7L) = 0 and the regulator is enabled, the device goes into Retention mode in Sleep 0 = The regulator is on when device’s Sleep mode is enabled and the Low-Power mode is controlled by the PMSLP bit bit 3 Unimplemented: Read as ‘0’ bit 2 DPSLP: Deep Sleep Wake-up Status bit (used in conjunction with the POR and BOR bits in RCON to determine the Reset source)(2) 1 = The last exit from Reset was caused by a normal wake-up from Deep Sleep 0 = The last exit from Reset was not due to a wake-up from Deep Sleep bit 1 Unimplemented: Read as ‘0’ bit 0 PMSLP: Program Memory Power During Sleep bit 1 = Program memory bias voltage remains powered during Sleep 0 = Program memory bias voltage is powered down during Sleep Note 1: 2: This bit is available only when RETEN (CONFIG7L) = 0. This bit is set in hardware only; it can only be cleared in software.  2012-2016 Microchip Technology Inc. DS30000575C-page 93 PIC18F97J94 FAMILY 5.2 Power-on Reset (POR) The PIC18F97J94 family has two types of Power-on Resets: • POR • VBAT POR POR is the legacy PIC18J series Power-on Reset which monitors core power supply. The second, VBAT POR, monitors voltage on the VBAT pin. These POR circuits use the same technique to enable and monitor their respective power source for adequate voltage levels to ensure proper chip operation. There are two threshold voltages associated with them. The first voltage is the device threshold voltage, VPOR. The device threshold voltage is the voltage at which the POR module becomes operable. The second voltage associated with a POR event is the POR circuit threshold voltage. Once the correct threshold voltage is detected, a power-on event occurs and the POR module hibernates to minimize current consumption. A power-on event generates an internal POR pulse when a VDD rise is detected. The device supply voltage characteristics must meet the specified starting voltage, VPOR, and rise rate requirements, SVDD, to generate the POR pulse. In particular, VDD must fall below VPOR before a new POR is initiated. For more information on the VPOR and VDD rise rate specifications, refer to Section 30.0 “Electrical Specifications”. 5.2.1 POR CIRCUIT The POR circuit behaves differently than VBAT POR once the POR state becomes active. The internal POR pulse resets the POR timer and places the device in the Reset state. The POR also selects the device clock source identified by the Oscillator Configuration bits. After the POR pulse is generated, the POR circuit inserts a small delay, TCSD, to ensure that internal device bias circuits are stable. DS30000575C-page 94 After the expiration of TCSD, a delay, TPWRT, is always inserted every time the device resumes operation after any power-down. During this time, code execution is disabled. The PWRT is used to extend the duration of a power-up sequence to permit the on-chip band gap and regulator to stabilize and to load the Configuration Word settings. The on-chip regulator is always enabled and its stabilization time is shorter than other concurrently running delays, and does not extend start-up time. The power-on event clears the BOR and POR Status bits (RCON); it does not change for any other Reset event. POR is not reset to ‘1’ by any hardware event. To capture multiple events, the user manually resets the bit to ‘1’ in software following any Power-on Reset. Alternatively, the VDDPOR (RCON3) bit can be used; it is set on a VDD POR event. It must be cleared after any Power-on Reset to detect subsequent VDD POR events. After TPWRT expires, an additional start-up time for the system clock (either TOST, TIOBST and TRC, depending on the source) occurs while the clock source becomes stable. Internal Reset is then released and the device is no longer held in Reset (Table 5-2). Once all of the delays have expired, the system clock is released and code execution can begin. Refer to Section 30.0 “Electrical Specifications” for more information on the values of the delay parameters. Note: When the device exits the Reset condition (begins normal operation), the device operating parameters (voltage, frequency, temperature, etc.) must be within their operating ranges; otherwise, the device will not function correctly. The user must ensure that the delay between the time power is first applied, and the time, INTERNAL RESET, becomes inactive, is long enough to get all operating parameters within specification.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 5-2: POR MODULE TIMING SEQUENCE FOR RISING VDD POR Circuit Threshold Voltage VDD VPOR Internal Power-on Reset Pulse Occurs and Begins POR Delay Time, TCSD POR TCSD POR Circuit is Initialized at VPOR System Clock is Started After TPWRT Delay Expires PWRT TPWRT System Clock is Released and Code Execution Begins SYSRST (Note 1) System Reset is Released After Clock is Stable Oscillator Delay INTERNAL RESET Time Note 1: Timer and interval are determined by the initial start-up oscillator configuration; TOSC is for external oscillator modes, TFRC is for the FRC Oscillator or TLPRC for the internal 31 kHz RC Oscillator.  2012-2016 Microchip Technology Inc. DS30000575C-page 95 PIC18F97J94 FAMILY 5.2.1.1 Using the POR Circuit To take advantage of the POR circuit, tie the MCLR pin directly to VDD. This will eliminate external RC components usually needed to create a POR delay. A minimum rise time for VDD is required. Refer to the “Electrical Characteristics” section of the specific device data sheet for more information. Depending on the application, a resistor may be required between the MCLR pin and VDD. This resistor can be used to decouple the MCLR pin from a noisy power supply rail. Figure 5-3 displays a possible POR circuit for a slow power supply ramp up. The external POR circuit is only required if the device would exit Reset before the device VDD is in the valid operating range. The diode, D, helps discharge the capacitor quickly when VDD powers down. FIGURE 5-3: EXTERNAL POWER-ON RESET CIRCUIT (FOR SLOW VDD POWER-UP) 5.2.2 The device will remain in VBAT mode as long as no power is present on VDD. The VBPOR is active when the device is operating in VBAT mode and deriving power from the VBAT pin. Similar to the POR, the circuit monitors VBAT voltage and holds the device in Reset until adequate voltage is present to power up the device. After exiting the VBAT POR condition, the VBPOR (RCON3) bit is set. All other registers will be in a POR state, including Deep Sleep semaphores. Minimum VBAT ramp time and rearm voltage requirements apply. Refer to Parameters D003 and D004 in Section 30.0 “Electrical Specifications” for details. The device does not execute code in VBAT mode. Also, there is no Power-up Timer associated with VBPOR. After VDD power is restored, the device exits VBAT mode and the VBAT (RCON3) bit is set. All other registers, except those associated with RTCC, its clock source and the Deep Sleep semaphores (DSGPRx), will be in a POR state. For more information about VBAT mode, see Section 4.5 “Vbat Mode”. 5.3 VDD VDD D R R1 C MCLR PIC18FXXJXX Note 1: External Power-on Reset circuit is required only if the VDD power-up slope is too slow. The diode, D, helps discharge the capacitor quickly when VDD powers down. 2: R < 40 k is recommended to make sure that the voltage drop across R does not violate the device’s electrical specification. 3: R1  1 k will limit any current flowing into MCLR from external capacitor, C, in the event of MCLR/VPP pin breakdown, due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). Master Clear Reset (MCLR) Whenever the MCLR pin is driven low, the device asynchronously asserts SYSRST, provided the input pulse on MCLR is longer than a certain minimum width, TMCL (see Section 30.0 “Electrical Specifications”). When the MCLR pin is released, SYSRST is also released. The Reset vector fetch starts from the SYSRST release. The processor continues to use the existing clock source that was in use before the MCLR Reset occurred. The EXTR Status bit (RCON2) is set to indicate the MCLR Reset. 5.4 Watchdog Timer Reset (WDT) Whenever a Watchdog Timer time-out occurs, the device asynchronously asserts SYSRST. The clock source remains unchanged. Note that a WDT time-out during Sleep or Idle mode will wake-up the processor, but NOT reset the processor. The TO bit (RCON) is cleared when a WDT time-out occurs. Software must set this bit to initialize the flag. For more information, refer to Section 28.2 “Watchdog Timer (WDT)”. Note: DS30000575C-page 96 VBAT POWER-ON-RESET (VBPOR) The WDT described here is not the same one used in Deep Sleep mode. For more information on Deep Sleep WDT, see Section 28.2 “Watchdog Timer (WDT)”.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 5.5 Configuration Mismatch Reset (CM) 5.6 The Configuration Mismatch (CM) Reset is designed to detect, and attempt to recover from, random memory corrupting events. These include Electrostatic Discharge (ESD) events, which can cause widespread, single bit changes throughout the device and result in catastrophic failure. In PIC18FXXJXX Flash devices, device Configuration registers (located in the configuration memory space) are continuously monitored during operation by comparing their values to complimentary shadow registers. If a mismatch is detected between the two sets of registers, a CM Reset automatically occurs. These events are captured by the CM bit (RCON) being set to ‘0’. This bit does not change for any other Reset event. A CM Reset behaves similarly to a Master Clear Reset, RESET instruction, WDT Time-out Reset or Stack Event Reset. As with all hard and power Reset events, the device’s Configuration Words are reloaded from the Flash Configuration Words in program memory as the device restarts. TABLE 5-1: Feature Brown-out Reset (BOR) Features The PIC97J94 family has four different types of BOR circuits: • • • • Brown-out Reset (BOR) VDDCORE Brown-out Reset (VDDBOR) VBAT Brown-out Reset (VBATBOR) Deep Sleep Brown-out Reset (DSBOR) All four BOR circuits monitor a voltage and put the device in a Reset condition while the voltage is in a specified region. SFRs will reset to the BOR state, including the Deep Sleep semaphore holding registers, DSGPR0 and DSGPR1. Upon BOR exit, the device remains in Reset until the associated trip point voltage is exceeded. Any I/O pins configured as outputs will be tri-stated. BOR, VDDBOR and DSBOR exit into Run mode; VBATBOR remains in VBAT mode. These features differ by their power mode, monitored voltage source, trip points, control and status. Refer to Table 5-1 for the PIC18F97J94 BOR differences. BOR FEATURE SUMMARY(1) Mode Source Trip Points BOR Run, Idle, Sleep VDDCORE 1.6V (typ) Always Enabled VDDBOR Run, Idle, Sleep VDD VVDDBOR BOREN (CONFIG1H) VBAT VBAT VVBATBOR VBTBOR (CONFIG7L) Deep Sleep VDD VDSBOR VBATBOR DSBOR Note 1: Enable DSBOREN (CONFIG7L) Refer to Table for details.  2012-2016 Microchip Technology Inc. DS30000575C-page 97 PIC18F97J94 FAMILY 5.6.1 BROWN-OUT RESET (BOR) Brown-out Reset is the legacy PIC18 “J” feature that monitors the core voltage, VDDCORE. Since the regulator on the PIC18F97J94 family is always enabled, this feature is always active. Its trip point is non-configurable. A Brown-out Reset will occur as the regulator output voltage drops below, approximately 1.6V. After proper operating voltage recovers, the Brown-out Reset condition is exited and execution begins after the Power-up Timer has expired. The BOR (RCON) bit is also cleared. This bit must be set after each Brown-out and Power-on Reset event to detect subsequent Brown-out Reset events. Note: 5.6.2 Brown-out Reset (BOR) has been provided to support legacy devices that can disable their internal regulator. The PIC18F97J94 family’s regulator is always enabled. Therefore, it’s recommended that new designs use VDDBOR to detect Brown-out conditions. VDD BOR (VDDBOR) VDDBOR is enabled by setting the BOREN (CONFIG1H) Configuration bit. The low-power BOR trip level is configurable to either 1.8V or 2.0V, (typ) depending on the BORV (CONFIG1H) Configuration bit setting. When in normal Run mode, Idle or normal Sleep modes, the BOR circuit that monitors VDD is active and will cause the device to be held in BOR if VDD drops below VBOR. Once VDD rises back above VVDDBOR, the device will be held in Reset until the expiration of the Power-up Timer, with period, TPWRT. This event is captured by the VDDBOR flag bit (RCON3). 5.6.3 DETECTING VDD BOR When the BOR module is enabled, the VDDBOR (RCON3) bit is set on a Brown-out Reset event. This makes it difficult to determine if a Brown-out Reset event has occurred just by reading the state of VDDBOR alone. A more reliable method is to simultaneously check the state of both VDDPOR and VDDBOR. This assumes that the VDDPOR bit is reset to ‘1’ in software immediately after any Power-on Reset event. If VDDBOR is ‘0’ while VDDPOR is ‘1’, it can be reliably assumed that a Brown-out Reset event has occurred. Legacy PIC18 software can use the respective POR (RCON) and BOR (RCON) bits. This technique monitors the regulator output voltage, VDDCORE. To take advantage of the configuration features, it is recommended to use VDDBOR instead of BOR. DS30000575C-page 98 5.6.4 VBAT BROWN-OUT RESET (VBATBOR) The VBAT BOR can be enabled/disabled using the VBTBOR bit in the Configuration register (CONFIG7L). If the VBTBOR enable bit is cleared, the VBATBOR is always disabled and there will be no indication of a VBAT BOR. If the VBTBOR bit is set, the VBAT POR will reset the device when the battery voltage drops below VVBATBOR. After power is restored to the VBAT pin, the device exits Reset and returns to VBAT mode. The device remains in VBAT mode until power returns to the VDD pin. For more information on using the VBAT feature, refer to Section 4.5 “Vbat Mode”. 5.6.5 DEEP SLEEP BROWN-OUT RESET (DSBOR) The PIC18F97J94 has its dedicated BOR for Deep Sleep mode (DSBOR). It is enabled through the DSBOREN (CONFIG7L) Configuration bit. When the device enters Deep Sleep mode and receives a DSBOR event, the device will not wake-up and will remain in Deep Sleep mode. When a valid wake-up event occurs and causes the device to exit Deep Sleep mode, software can determine if a DSBOR event occurred during Deep Sleep mode by reading the DSBOR (DSCONL) Status bit. 5.7 RESET Instruction Whenever the RESET instruction is executed, the device asserts SYSRST. This Reset state does not reinitialize the clock. The clock source that is in effect prior to the RESET instruction remains in effect. Configuration settings are updated and the SYSRST is released at the next instruction cycle. A noise filter in the MCLR Reset path detects and ignores small pulses. The RI bit (RCON) is cleared when a RESET instruction is executed. Software must set this bit to initialize the flag. 5.8 Stack Underflow/Overflow Reset A Reset can be enabled on stack error conditions by setting the STVREN (CONFIG1L) Configuration bit. See Section 6.1.4.4 “Stack Full and Underflow Resets”section for additional information.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 5.9 Device Reset Timers PIC18F97J94 family devices incorporate three separate on-chip timers that help regulate the Power-on Reset process. Their main function is to ensure that the device clock is stable before code is executed. These timers are: • Power-up Timer (PWRT) • Oscillator Start-up Timer (OST) • PLL Lock Time-out 5.9.1 POWER-UP TIMER (PWRT) The Power-up Timer (PWRT) of the PIC18F97J94 family devices is a counter which uses the INTOSC source as the clock input. While the PWRT is counting, the device is held in Reset. The power-up time delay depends on the INTOSC clock and varies slightly from chip-to-chip due to temperature and process variation. See the TPWRT specification for details. The PWRT is always enabled and active after Brown-out and Poweron Reset events. 5.9.2 OSCILLATOR START-UP TIMER (OST) The Oscillator Start-up Timer (OST) provides a 1024 oscillator cycle (from OSC1 input) delay after the PWRT delay is over. This ensures that the crystal oscillator or resonator has started and stabilized. 5.9.3 PLL LOCK TIME-OUT The PLL is enabled by programming FOSC = 011 (CONFIG2L. With the PLL enabled, the time-out sequence, following a Power-on Reset, is slightly different from other oscillator modes. A separate timer is used to provide a fixed time-out that is sufficient for the PLL to lock to the main oscillator frequency. This PLL lock timeout (TRC) follows the oscillator start-up time-out. 5.9.4 RESET STATE OF REGISTERS Most registers are unaffected by a Reset. Their status is unknown on a Power-on Reset and unchanged by all other Resets. The other registers are forced to a “Reset state” depending on the type of Reset that occurred. Most registers are not affected by a WDT wake-up, since this is viewed as the resumption of normal operation. Status bits from the RCONx registers are set or cleared differently in different Reset situations, as indicated in Table 5-2. These bits are used in software to determine the nature of the Reset. Table 5-2 describes the Reset states for all of the Special Function Registers. These are categorized by Power-on and Brown-out Resets, Master Clear and WDT Resets, and WDT wake-ups. The OST time-out is invoked only for LP, MS, HS and HSPLL modes, and only on Power-on Reset or on exit from most power-managed modes.  2012-2016 Microchip Technology Inc. DS30000575C-page 99 PIC18F97J94 FAMILY DPSLP EXTR RI TO PD IDLE CM BOR POR VDDBOR VDDPOR VBPOR(4,6) VBAT(4) RCONx BIT OPERATION ON VARIOUS RESETS AND WAKE-UPS PC TABLE 5-2: DSPOR:(4) Loss of VDDBAT 000000 0 0 0 0 1 0 0 1 1 1 1 1 0 VBAT:(4) Loss of VDD While VBAT is Established 000000 1 0 0 0 1 0 0 1 1 1 1 u 1 VDD POR: Loss of VDD 000000 0 0 0 0 1 0 0 1 1 1 1 u u VDD BOR: Brown-out of VDD 000000 u u 0 0 1 0 0 u u 1 u u u POR: Loss of VDDCORE 000000 0 0 0 0 1 0 0 1 1 u u u u BOR Brown-out of VDDCORE 000000 u u 0 0 1 0 0 1 u u u u u Deep Sleep Exit 000000 1 0 0 0 1 0 0 1 1 u u u u Retention Deep Sleep Exit 000000 1 0 0 0 1 0 0 0 0 u u u u MCLR Reset Operational Mode 000000 u 1 u u u u u u u u u u u MCLR Reset in Idle Mode 000000 u 1 u 0(1) 0(2) 1(2) u u u u u u u (1) (2) 0(2) u u u u u u u u u u u u u Conditions MCLR Reset in Sleep Mode 000000 u 1 u RESET Instruction Reset 000000 u u 1 Configuration Mismatch Reset 000000 u u WDT Reset 000000 u u WDT Reset in Idle Mode PC + 2 u WDT Reset in Sleep Mode PC + 2 u 0 0 u u u u u u u u 1 u u u u u u u 1 u u u u u u u u u u u 1 1(2) 1(2) u u u u u u u u u 1 0 (2) 0 (2) u u u u u u u 1 (2) 1 (2) u u u u u u u Interrupt in Idle Mode with GIE = 0 PC + 2 u u u 0(1) Interrupt in Idle Mode with GIE = 1 Vector u u u 0(1) 1(2) 1(2) u u u u u u u Interrupt in Sleep Mode With GIE = 0 PC + 2 u u u 0(1) 0(2) 0(2) u u u u u u u Interrupt in Sleep Mode with GIE = 1 Vector u u u 0(1) 0(2) 0(2) u u u u u u u CLRWDT Instruction PC + 2 u u u 0(3) 1 u u u u u u u u IDLE Instruction PC + 2 u u u 0 1 1 u u u u u u u SLEEP Instruction PC + 2 u u u 0 0 0 u u u u u u u User Instruction Writes ‘1’ PC + 2 u 1 1 1 0 1 1 1 1 1 1 1 1 User Instruction Writes ‘0’ PC + 2 0 0 0 0 1 0 0 0 0 0 0 0 0 Note 1: 2: 3: 4: 5: 6: The SLEEP instruction clears the WDTO bit. The CLRWDT clears the WDTO bit only when the WDT window feature is disabled or the WDT is in the safe window. This bit is also set, flagging the loss of state retention even though the true POR condition has not occurred. This bit is set in hardware only; it can only be cleared in software. Indicates a VDD POR. Setting the POR bit (RCON) indicates a VCORE POR. This bit is set when the device is originally powered up, even if power is present on VBAT. DS30000575C-page 100  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 5-3: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets TOSU 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---0 uuuu(1) TOSH 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu(1) TOSL 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu(1) STKPTR 64-pin 80-pin 100-pin 00-0 0000 uu-0 0000 uu-u uuuu(1) PCLATU 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu PCLATH 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PCL 64-pin 80-pin 100-pin 0000 0000 0000 0000 PC + 2(2) TBLPTRU 64-pin 80-pin 100-pin --00 0000 --00 0000 --uu uuuu TBLPTRH 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu TBLPTRL 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu TABLAT 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PRODH 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu PRODL 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu INTCON 64-pin 80-pin 100-pin 0000 000x 0000 000x uuuu uuuu(3) INTCON2 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu(3) INTCON3 64-pin 80-pin 100-pin 1100 0000 1100 0000 uuuu uuuu(3) INDF0 64-pin 80-pin 100-pin N/A N/A N/A POSTINC0 64-pin 80-pin 100-pin N/A N/A N/A POSTDEC0 64-pin 80-pin 100-pin N/A N/A N/A PREINC0 64-pin 80-pin 100-pin N/A N/A N/A PLUSW0 64-pin 80-pin 100-pin N/A N/A FSR0H 64-pin 80-pin 100-pin ---- xxxx ---- uuuu ---- uuuu N/A FSR0L 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu WREG 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu INDF1 64-pin 80-pin 100-pin N/A N/A N/A POSTINC1 64-pin 80-pin 100-pin N/A N/A N/A POSTDEC1 64-pin 80-pin 100-pin N/A N/A N/A PREINC1 64-pin 80-pin 100-pin N/A N/A N/A PLUSW1 64-pin 80-pin 100-pin N/A N/A FSR1H 64-pin 80-pin 100-pin ---- xxxx ---- uuuu ---- uuuu N/A FSR1L 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu BSR 64-pin 80-pin 100-pin ---- 0000 ---- 0000 ---- uuuu INDF2 64-pin 80-pin 100-pin N/A N/A N/A Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR.  2012-2016 Microchip Technology Inc. DS30000575C-page 101 PIC18F97J94 FAMILY TABLE 5-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets POSTINC2 64-pin 80-pin 100-pin N/A N/A N/A POSTDEC2 64-pin 80-pin 100-pin N/A N/A N/A PREINC2 64-pin 80-pin 100-pin N/A N/A N/A PLUSW2 64-pin 80-pin 100-pin N/A N/A N/A FSR2H 64-pin 80-pin 100-pin ---- xxxx ---- uuuu ---- uuuu FSR2L 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu STATUS 64-pin 80-pin 100-pin ---x xxxx ---u uuuu ---u uuuu TMR0H 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu TMR0L 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu T0CON 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RESERVED 64-pin 80-pin 100-pin ---- ---- ---- ---- ---- ---- OSCCON 64-pin 80-pin 100-pin 0qqq -qqq uuuu -uuu uuuu -uuu IPR5 64-pin 80-pin 100-pin -111 -111 -uuu -uuu -uuu -uuu IOCF 64-pin 80-pin 100-pin 0000 0000 0000 0000 qqqq qqqq (4) RCON 64-pin 80-pin 100-pin 0-11 11qq 0-qq qquu u-qq qquu TMR1H 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu TMR1L 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu T1CON 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu TMR2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PR2 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu T2CON 64-pin 80-pin 100-pin -000 0000 -000 0000 -uuu uuuu SSP1BUF 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu SSP1ADD 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SSP1STAT 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SSP1CON1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SSP1CON2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu CMSTAT 64-pin 80-pin 100-pin ---- -xxx ---- -uuu ---- -uuu ADCBUF0H 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu ADCBUF0L 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu ADCON1H 64-pin 80-pin 100-pin 0--- -000 u--- -uuu u--- -uuu ADCON1L 64-pin 80-pin 100-pin 0000 -000 uuuu -uuu uuuu -uuu CVRCONH 64-pin 80-pin 100-pin ---0 0000 ---u uuuu ---u uuuu CVRCONL 64-pin 80-pin 100-pin 0000 ---0 uuuu ---u uuuu ---u Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR. DS30000575C-page 102  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 5-3: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets ECCP1AS 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ECCP1DEL 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu CCPR1H 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu CCPR1L 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu CCP1CON 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PIR5 64-pin 80-pin 100-pin -000 -0000 -000 -000 -uuu -uuu(3) PIE5 64-pin 80-pin 100-pin -000 -000 -000 -000 -uuu -uuu IPR4 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu PIR4 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu(3) PIE4 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu TMR3H 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu TMR3L 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu T3CON 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu T3GCON 64-pin 80-pin 100-pin 0000 0x00 0000 00x0 uuuu uuuu SPBRG1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RCREG1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu TXREG1 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu TXSTA1 64-pin 80-pin 100-pin 0000 0010 0000 0010 uuuu uuuu RCSTA1 64-pin 80-pin 100-pin 0000 000x 0000 000x uuuu uuuu T1GCON 64-pin 80-pin 100-pin 0000 0x00 0000 0x00 uuuu uuuu IPR6 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu HLVDCON 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PSPCON 64-pin 80-pin 100-pin 0000 ---- 0000 ---- uuuu ---- PIR6 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu(3) IPR3 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu PIR3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu(3) PIE3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu IPR2 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu PIR2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu(3) PIE2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu IPR1 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu PIR1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu(3) PIE1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR.  2012-2016 Microchip Technology Inc. DS30000575C-page 103 PIC18F97J94 FAMILY TABLE 5-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets PSTR1CON 64-pin 80-pin 100-pin 00-0 0001 00-0 0001 uu-u uuuu OSCTUNE 64-pin 80-pin 100-pin --00 0000 --00 0000 --uu uuuu TRISJ 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu TRISH 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu TRISG(5) 64-pin 80-pin 100-pin 11-1 1111 11-1 1111 uu-u uuuu TRISF 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu TRISE 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu TRISD 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu TRISC 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu TRISB 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu TRISA 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu LATJ 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu LATH 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu LATG(5) 64-pin 80-pin 100-pin xx-x xxxx uu-u uuuu uu-u uuuu LATF 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu LATE 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu LATD 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu LATC 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu LATB 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu LATA 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu PORTJ 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu PORTH 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu PORTG(5) 64-pin 80-pin 100-pin xx-x x-xx xx-x x-xx uu-u u-uu PORTF 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu PORTE 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu PORTD 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu PORTC 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu PORTB 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu PORTA 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu EECON1 64-pin 80-pin 100-pin xx-0 x000 uu-0 u000 uu-u uuuu EECON2 64-pin 80-pin 100-pin ---- ---- ---- ---- ---- ---- RCON2 64-pin 80-pin 100-pin 0-0- 0--- q-u- 0--- 0-u- 1--- RCON3 64-pin 80-pin 100-pin ---0 q000 ---u 0000 ---u 0000 Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR. DS30000575C-page 104  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 5-3: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets RCON4 64-pin 80-pin 100-pin 00-0 -0-0 00-u -0-u 00-u -0-u UFRML 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu UFRMH 64-pin 80-pin 100-pin ---- -xxx ---- -xxx ---- -uuu UIR 64-pin 80-pin 100-pin -000 0000 -000 0000 -uuu uuuu UEIR 64-pin 80-pin 100-pin -000 0000 -000 0000 -uuu uuuu USTAT 64-pin 80-pin 100-pin 0--0 0000 0--0 0000 u--u uuuu UCON 64-pin 80-pin 100-pin -0x0 000- -0x0 000- -uuu uuu- UADDR 64-pin 80-pin 100-pin -000 0000 -000 0000 -uuu uuuu TRISVP 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu LATVP 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu PORTVP 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu TXADDRL 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu TXADDRH 64-pin 80-pin 100-pin ---- 0000 ---- 0000 ---- uuuu RXADDRL 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RXADDRH 64-pin 80-pin 100-pin ---- 0000 ---- 0000 ---- uuuu DMABCL 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu DMABCH 64-pin 80-pin 100-pin ---- --00 ---- --00 ---- --uu TXBUF 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SSP1CON3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SSP1MSK 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu BAUDCON1 64-pin 80-pin 100-pin 0100 0000 0100 0000 uuuu uuuu OSCCON2 64-pin 80-pin 100-pin 000- 000- 00q- 000- uuu- uuu- OSCCON3 64-pin 80-pin 100-pin ---- -001 ---- -uuu ---- -uuu OSCCON4 64-pin 80-pin 100-pin 000- ---- uuu- ---- uuu- ---- OSCCON5 64-pin 80-pin 100-pin 0-00 0000 u-uu uuuu u-uu uuuu WPUB 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu PIE6 64-pin 80-pin 100-pin 0000 -000 0000 -000 uuuu -uuu DMACON1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RTCCON1 64-pin 80-pin 100-pin 0-00 0000 u-uu uuuu u-uu uuuu RTCCAL 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu RTCVALH 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu RTCVALL 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu ALRMCFG 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR.  2012-2016 Microchip Technology Inc. DS30000575C-page 105 PIC18F97J94 FAMILY TABLE 5-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets ALRMRPT 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu ALRMVALH 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu ALRMVALL 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu RTCCON2 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu IOCP 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu IOCN 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PADCFG1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu CM1CON 64-pin 80-pin 100-pin 0001 1111 0001 1111 uuuu uuuu ECCP2AS 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ECCP2DEL 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu CCPR2H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCPR2L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ECCP2CON 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ECCP3AS 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ECCP3DEL 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu CCPR3H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCPR3L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ECCP3CON 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu CCPR8H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCPR8L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCP8CON 64-pin 80-pin 100-pin --00 0000 --00 0000 --uu uuuu CCPR9H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCPR9L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCP9CON 64-pin 80-pin 100-pin --00 0000 --00 0000 --uu uuuu CCPR10H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCPR10L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCP10CON 64-pin 80-pin 100-pin --00 0000 --00 0000 --uu uuuu TMR6 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PR6 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu T6CON 64-pin 80-pin 100-pin -000 0000 -000 0000 -uuu uuuu TMR8 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PR8 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu T8CON 64-pin 80-pin 100-pin -000 0000 -000 0000 -uuu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR. DS30000575C-page 106  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 5-3: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets SSP2CON3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu CM2CON 64-pin 80-pin 100-pin 0001 1111 0001 1111 uuuu uuuu CM3CON 64-pin 80-pin 100-pin 0001 1111 0001 1111 uuuu uuuu CCPTMRS0 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu CCPTMRS1 64-pin 80-pin 100-pin 00-0 -000 00-0 -000 uuuu uuuu CCPTMRS2 64-pin 80-pin 100-pin ---0 -000 ---0 -000 uuuu uuuu RCSTA2 64-pin 80-pin 100-pin 0000 000x 0000 000x uuuu uuuu TXSTA2 64-pin 80-pin 100-pin 0000 0010 0000 0010 uuuu uuuu BAUDCON2 64-pin 80-pin 100-pin 01x0 0000 01x0 0000 uuuu uuuu SPBRGH1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RCSTA3 64-pin 80-pin 100-pin 0000 000x 0000 000x uuuu uuuu TXSTA3 64-pin 80-pin 100-pin 0000 0010 0000 0010 uuuu uuuu BAUDCON3 64-pin 80-pin 100-pin 01x0 0000 01x0 0000 uuuu uuuu SPBRGH3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SPBRG3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RCREG3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu TXREG3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu DSCONL 64-pin 80-pin 100-pin ---- -000 ---- -000 --- -uuu DSCONH 64-pin 80-pin 100-pin 0-0- ---0 u-u- ---u u-u- ---u DSWAKEL 64-pin 80-pin 100-pin 0000 0001 uuuu uuuu uuuu uuuu DSWAKEH 64-pin 80-pin 100-pin ---- ---0 ---- ---u ---- ---q DSGPR0(6) 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu DSGPR1(6) 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu DSGPR2(6) 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu DSGPR3 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu SPBRGH2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SPBRG2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RCREG2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu TXREG2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PSTR2CON 64-pin 80-pin 100-pin 00-0 0001 00-0 0001 uu-u uuuu PSTR3CON 64-pin 80-pin 100-pin 00-0 0001 00-0 0001 uu-u uuuu SSP2STAT 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SSP2CON1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR.  2012-2016 Microchip Technology Inc. DS30000575C-page 107 PIC18F97J94 FAMILY TABLE 5-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets SSP2CON2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SSP2MSK 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu TMR5H 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu TMR5L 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu T5CON 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu T5GCON 64-pin 80-pin 100-pin 0000 0x00 0000 00x0 uuuu uuuu CCPR4H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCPR4L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCP4CON 64-pin 80-pin 100-pin --00 0000 --00 0000 --uu uuuu CCPR5H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCPR5L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCP5CON 64-pin 80-pin 100-pin --00 0000 --00 0000 --uu uuuu CCPR6H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCPR6L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCP6CON 64-pin 80-pin 100-pin --00 0000 --00 0000 --uu uuuu CCPR7H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCPR7L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu CCP7CON 64-pin 80-pin 100-pin --00 0000 --00 0000 --uu uuuu TMR4 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu PR4 64-pin 80-pin 100-pin 1111 1111 uuuu uuuu uuuu uuuu T4CON 64-pin 80-pin 100-pin -000 0000 -000 0000 -uuu uuuu SSP2BUF 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu SSP2ADD 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ANCFG 64-pin 80-pin 100-pin ---- -000 ---- -000 ---- -uuu DMACON2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RCSTA4 64-pin 80-pin 100-pin 0000 000x 0000 000x uuuu uuuu TXSTA4 64-pin 80-pin 100-pin 0000 0010 0000 0010 uuuu uuuu BAUDCON4 64-pin 80-pin 100-pin 01x0 0000 01x0 0000 uuuu uuuu SPBRGH4 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu SPBRG4 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RCREG4 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu TXREG4 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu CTMUCON 64-pin 80-pin 100-pin 0-00 0000 0-00 0000 u-uu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR. DS30000575C-page 108  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 5-3: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets CTMUCON1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu CTMUCON2 64-pin 80-pin 100-pin 0000 00-- 0000 00-- uuuu uu-- CTMUCON3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PMD0 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PMD1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PMD2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PMD3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu PMD4 64-pin 80-pin 100-pin 0000 00-- 0000 00-- uuuu uu-- MDCON 64-pin 80-pin 100-pin 0010 0--0 0010 0--0 uuuu u--u MDSRC 64-pin 80-pin 100-pin 0--- xxxx 0--- uuuu u--- uuuu MDCARH 64-pin 80-pin 100-pin 0xx- xxxx 0uu- uuuu uuu- uuuu MDCARL 64-pin 80-pin 100-pin 0xx- xxxx 0uu- uuuu uuu- uuuu ODCON1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ODCON2 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu TRISK 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu LATK 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu PORTK 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu TRISL 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu LATL 64-pin 80-pin 100-pin xxxx xxxx uuuu uuuu uuuu uuuu PORTL 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu MEMCON 64-pin 80-pin 100-pin 0-00 --00 0-00 --00 u-uu --uu REFO1CON 64-pin 80-pin 100-pin 0-00 0-00 u-uu u-uu u-uu u-uu REFO1CON1 64-pin 80-pin 100-pin ---- 0000 ---- uuuu ---- uuuu REFO1CON2 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu REFO1CON3 64-pin 80-pin 100-pin -000 0000 -uuu uuuu -uuu uuuu REFO2CON 64-pin 80-pin 100-pin 0-00 0-00 u-uu u-uu u-uu u-uu REFO2CON1 64-pin 80-pin 100-pin ---- 0000 ---- uuuu ---- uuuu REFO2CON2 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu REFO2CON3 64-pin 80-pin 100-pin -000 0000 -uuu uuuu -uuu uuuu LCDPS 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDREG 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDCON 64-pin 80-pin 100-pin 0000 0000 0000 0000 u-uu uuuu LCDREF 64-pin 80-pin 100-pin 0-00 0000 u-uu uuuu u-uu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR.  2012-2016 Microchip Technology Inc. DS30000575C-page 109 PIC18F97J94 FAMILY TABLE 5-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets LCDREFL 64-pin 80-pin 100-pin 0000 -000 uuuu -uuu uuuu -uuu LCDSE7 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDSE6 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDSE5 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDSE4 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDSE3 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDSE2 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDSE1 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDSE0 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA63 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA62 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA61 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA60 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA59 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA58 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA57 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA56 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA55 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA54 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA53 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA52 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA51 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA50 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA49 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA48 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA47 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA46 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA45 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA44 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA43 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA42 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA41 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA40 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR. DS30000575C-page 110  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 5-3: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets LCDDATA39 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA38 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA37 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA36 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA35 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA34 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA33 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA32 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA31 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA30 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA29 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA28 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA27 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA26 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA25 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA24 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA23 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA22 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA21 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA20 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA19 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA18 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA17 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA16 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA15 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA14 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA13 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA12 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA11 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA10 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA9 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA8 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA7 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR.  2012-2016 Microchip Technology Inc. DS30000575C-page 111 PIC18F97J94 FAMILY TABLE 5-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets LCDDATA6 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA5 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA4 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA3 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA2 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA1 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu LCDDATA0 64-pin 80-pin 100-pin 0000 0000 uuuu uuuu uuuu uuuu ADCON2H 64-pin 80-pin 100-pin 0000 00-- 0000 00-- uuuu uu-- ADCON2L 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCON3H 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCON3L 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCON5H 64-pin 80-pin 100-pin 000- --00 000- --00 uuu- --uu ADCON5L 64-pin 80-pin 100-pin ---- 0000 ---- 0000 ---- uuuu ADCHS0H 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCHS0L 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCSS1H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCSS1L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCSS0H 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCSS0L 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCHIT1H 64-pin 80-pin 100-pin ---- --00 ---- --00 ---- --uu ADCHIT1L 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCHIT0H 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCHIT0L 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCTMUEN1H 64-pin 80-pin 100-pin -000 0000 -000 0000 uuuu uuuu ADCTMUEN1L 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCTMUEN0H 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCTMUEN0L 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu ADCBUF25H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF25L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF24H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF24L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF23H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF23L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR. DS30000575C-page 112  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 5-3: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets ADCBUF22H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF22L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF21H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF21L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF20H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF20L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF19H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF19L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF18H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF18L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF17H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF17L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF16H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF16L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF15H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF15L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF14H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF14L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF13H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF13L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF12H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF12L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF11H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF11L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF10H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF10L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF9H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF9L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF8H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF8L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF7H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF7L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF6H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR.  2012-2016 Microchip Technology Inc. DS30000575C-page 113 PIC18F97J94 FAMILY TABLE 5-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets ADCBUF6L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF5H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF5L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF4H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF4L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF3H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF3L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF2H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF2L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF1H 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ADCBUF1L 64-pin 80-pin 100-pin xxxx xxxx xxxx xxxx uuuu uuuu ANCON1 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu ANCON2 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu ANCON3 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR52_53 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR50_51 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR48_49 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR46_47 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR44_45 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR42_43 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR40_41 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR38_39 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR36_37 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR34_35 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR32_33 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR30_31 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR28_29 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR26_27 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR24_25 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR22_23 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR20_21 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR18_19 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR16_17 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR. DS30000575C-page 114  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 5-3: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets RPINR14_15 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR12_13 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR10_11 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR8_9 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR6_7 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR4_5 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR2_3 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPINR0_1 64-pin 80-pin 100-pin 1111 1111 1111 1111 uuuu uuuu RPOR46 64-pin 80-pin 100-pin ---- 0000 ---- 0000 ---- uuuu RPOR44_45 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR42_43 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR40_41 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR38_39 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR36_37 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR34_35 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR32_33 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR30_31 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR28_29 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR26_27 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR24_25 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR22_23 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR20_21 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR18_19 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR16_17 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR14_15 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR12_13 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR10_11 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR8_9 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR6_7 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR4_5 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR2_3 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu RPOR0_1 64-pin 80-pin 100-pin 0000 0000 0000 0000 uuuu uuuu UCFG 64-pin 80-pin 100-pin 00-0 -000 00-0 -000 uu-u -uuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR.  2012-2016 Microchip Technology Inc. DS30000575C-page 115 PIC18F97J94 FAMILY TABLE 5-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices MCLR Resets, Power-on Reset, WDT Reset, Wake-up via Brown-out RESET Instruction, WDT or Interrupt Reset Stack Resets UIE 64-pin 80-pin 100-pin -000 0000 -000 0000 -uuu uuuu UEIE 64-pin 80-pin 100-pin 0--0 0000 0--0 0000 u--u uuuu UEP0 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP1 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP2 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP3 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP4 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP5 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP6 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP7 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP8 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP9 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP10 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP11 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP12 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP13 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP14 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu UEP15 64-pin 80-pin 100-pin ---0 0000 ---0 0000 ---u uuuu Legend: u = unchanged; x = unknown; - = unimplemented bit, read as ‘0’; q = value depends on condition. Shaded cells indicate that conditions do not apply for the designated device. Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. 2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). 3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). 4: See Table 5-2 for Reset value for specific condition. 5: Bits 7,6 are unimplemented on 64 and 80-pin devices. 6: If the VBAT is always powered, the DSGPx register values will remain unchanged after the first POR. DS30000575C-page 116  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 6.0 MEMORY ORGANIZATION PIC18FXXJ94 devices have these types of memory: • Program Memory • Data RAM FIGURE 6-1: As Harvard architecture devices, the data and program memories use separate buses. This enables concurrent access of the two memory spaces. Additional detailed information on the operation of the Flash program memory is provided in Section 7.0 “Flash Program Memory”. MEMORY MAPS FOR PIC18F97J94 FAMILY DEVICES PC CALL, CALLW, RCALL, RETURN, RETFIE, RETLW, ADDULNK, SUBULNK 21 Stack Level 1   Stack Level 31 PIC18FX6J94 On-Chip Memory PIC18FX7J94 On-Chip Memory Config Words 007FFFh Config Words 00FFFFh Config Words Note: 000000h Unimplemented Unimplemented Unimplemented Read as ‘0’ Read as ‘0’ Read as ‘0’ 01FFFFh User Memory Space PIC18FX5J94 On-Chip Memory 1FFFFFh Sizes of memory areas are not to scale. Sizes of program memory areas are enhanced to show detail.  2012-2016 Microchip Technology Inc. DS30000575C-page 117 PIC18F97J94 FAMILY 6.1 Program Memory Organization PIC18 microcontrollers implement a 21-bit Program Counter that is capable of addressing a 2-Mbyte program memory space. Accessing a location between the upper boundary of the physically implemented memory and the 2-Mbyte address will return all ‘0’s (a NOP instruction). The entire PIC18FXXJ94 offers a range of on-chip Flash program memory sizes, from 32 Kbytes (up to 16,384 single-word instructions) to 128 Kbytes (65,536 single-word instructions). • PIC18F65J94, PIC18F85J94 and PIC18F95J94 – 32 Kbytes of Flash memory, storing up to 16,384 single-word instructions • PIC18F66J94, PIC18F86J94 and PIC18F96J94 – 64 Kbytes of Flash memory, storing up to 32,768 single-word instructions • PIC18F67J94, PIC18F87J94 and PIC18F97J94 – 128 Kbytes of Flash memory, storing up to 65,536 single-word instructions The program memory maps for individual family members are shown in Figure 6-1. 6.1.1 HARD MEMORY VECTORS All PIC18 devices have a total of three hard-coded return vectors in their program memory space. The Reset vector address is the default value to which the Program Counter returns on all device Resets; it is located at 0000h. TABLE 6-1: FLASH CONFIGURATION WORD FOR PIC18FXXJ94 FAMILY DEVICES Program Memory (Kbytes) Configuration Word Addresses PIC18F65J94 PIC18F85J94 PIC18F95J94 32 7FF0h to 7FFFh PIC18F66J94 PIC18F86J94 PIC18F96J94 64 FFF0h to FFFFh PIC18F67J94 PIC18F87J94 PIC18F97J94 128 1FFF0h to 1FFFFh Device FIGURE 6-2: HARD VECTOR FOR PIC18F97J94 FAMILY DEVICES Reset Vector 0000h High-Priority Interrupt Vector 0008h Low-Priority Interrupt Vector 0018h On-Chip Program Memory PIC18 devices also have two interrupt vector addresses for handling high-priority and low-priority interrupts. The high-priority interrupt vector is located at 0008h and the low-priority interrupt vector is at 0018h. The locations of these vectors are shown, in relation to the program memory map, in Figure 6-2. Flash Configuration Words 6.1.2 FLASH CONFIGURATION WORDS Because PIC18FXXJ94 devices do not have persistent configuration memory, the top eight words of on-chip program memory are reserved for configuration information. On Reset, the configuration information is copied into the Configuration registers. The Configuration Words are stored in their program memory location in numerical order, starting with the lower byte of CONFIG1 at the lowest address and ending with the upper byte of CONFIG8. The actual addresses of the Flash Configuration Word for devices in the PIC18FXXJ94 are shown in Table 6-1. Their location in the memory map is shown with the other memory vectors in Figure 6-2. Additional details on the device Configuration Words are provided in Section 28.1 “Configuration Bits”. DS30000575C-page 118 (Top of Memory-17) (Top of Memory) Read ‘0’ 1FFFFFh Legend: (Top of Memory) represents upper boundary of on-chip program memory space (see Figure 6-1 for device-specific values). Shaded area represents unimplemented memory. Areas are not shown to scale.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 6.1.3 PROGRAM COUNTER The Program Counter (PC) specifies the address of the instruction to fetch for execution. The PC is 21 bits wide and contained in three separate 8-bit registers. The low byte, known as the PCL register, is both readable and writable. The high byte, or PCH register, contains the PC bits and is not directly readable or writable. Updates to the PCH register are performed through the PCLATH register. The upper byte is called PCU. This register contains the PC bits; it is also not directly readable or writable. Updates to the PCU register are performed through the PCLATU register. The contents of PCLATH and PCLATU are transferred to the Program Counter by any operation that writes PCL. Similarly, the upper two bytes of the Program Counter are transferred to PCLATH and PCLATU by an operation that reads PCL. This is useful for computed offsets to the PC (see Section 6.1.6.1 “Computed GOTO”). The PC addresses bytes in the program memory. To prevent the PC from becoming misaligned with word instructions, the Least Significant bit of PCL is fixed to a value of ‘0’. The PC increments by two to address sequential instructions in the program memory. The CALL, RCALL, GOTO and program branch instructions write to the Program Counter directly. For these instructions, the contents of PCLATH and PCLATU are not transferred to the Program Counter. 6.1.4 RETURN ADDRESS STACK The return address stack enables execution of any combination of up to 31 program calls and interrupts. The PC is pushed onto the stack when a CALL or RCALL instruction is executed or an interrupt is Acknowledged. The PC value is pulled off the stack on a RETURN, RETLW or a RETFIE instruction. The value also is pulled off the stack on ADDULNK and SUBULNK instructions, if the extended instruction set is enabled. PCLATU and PCLATH are not affected by any of the RETURN or CALL instructions. FIGURE 6-3: The stack operates as a 31-word by 21-bit RAM and a 5-bit Stack Pointer, STKPTR. The stack space is not part of either program or data space. The Stack Pointer is readable and writable and the address on the top of the stack is readable and writable through the Top-ofStack Special Function Registers. Data can also be pushed to, or popped from, the stack using these registers. A CALL type instruction causes a push onto the stack. The Stack Pointer is first incremented and the location pointed to by the Stack Pointer is written with the contents of the PC (already pointing to the instruction following the CALL). A RETURN type instruction causes a pop from the stack. The contents of the location pointed to by the STKPTR are transferred to the PC and then the Stack Pointer is decremented. The Stack Pointer is initialized to ‘00000’ after all Resets. There is no RAM associated with the location corresponding to a Stack Pointer value of ‘00000’; this is only a Reset value. Status bits indicate if the stack is full, has overflowed or has underflowed. 6.1.4.1 Top-of-Stack Access Only the top of the return address stack (TOS) is readable and writable. A set of three registers, TOSU:TOSH:TOSL, holds the contents of the stack location pointed to by the STKPTR register (Figure 6-3). This allows users to implement a software stack, if necessary. After a CALL, RCALL or interrupt (or ADDULNK and SUBULNK instructions, if the extended instruction set is enabled), the software can read the pushed value by reading the TOSU:TOSH:TOSL registers. These values can be placed on a user-defined software stack. At return time, the software can return these values to TOSU:TOSH:TOSL and do a return. While accessing the stack, users must disable the Global Interrupt Enable bits to prevent inadvertent stack corruption. RETURN ADDRESS STACK AND ASSOCIATED REGISTERS Return Address Stack Top-of-Stack Registers TOSU 00h TOSH 1Ah 11111 11110 11101 TOSL 34h Top-of-Stack  2012-2016 Microchip Technology Inc. 001A34h 000D58h Stack Pointer STKPTR 00010 00011 00010 00001 00000 DS30000575C-page 119 PIC18F97J94 FAMILY 6.1.4.2 Return Stack Pointer (STKPTR) The STKPTR register (Register 6-1) contains the Stack Pointer value, the STKFUL (Stack Full) Status bit and the STKUNF (Stack Underflow) Status bits. The value of the Stack Pointer can be 0 through 31. The Stack Pointer increments before values are pushed onto the stack and decrements after values are popped off the stack. On Reset, the Stack Pointer value will be zero. When the stack has been popped enough times to unload the stack, the next pop will return a value of zero to the PC and set the STKUNF bit, while the Stack Pointer remains at zero. The STKUNF bit will remain set until cleared by software or until a POR occurs. Note: The user may read and write the Stack Pointer value. This feature can be used by a Real-Time Operating System (RTOS) for return-stack maintenance. After the PC is pushed onto the stack, 31 times (without popping any values off the stack), the STKFUL bit is set. The STKFUL bit is cleared by software or by a POR. What happens when the stack becomes full depends on the state of the STVREN (Stack Overflow Reset Enable) Configuration bit. (For a description of the device Configuration bits, see Section 28.1 “Configuration Bits”.) If STVREN is set (default), the 31st push will push the (PC + 2) value onto the stack, set the STKFUL bit and reset the device. The STKFUL bit will remain set and the Stack Pointer will be set to zero. If STVREN is cleared, the STKFUL bit will be set on the 31st push and the Stack Pointer will increment to 31. Any additional pushes will not overwrite the 31st push and the STKPTR will remain at 31. REGISTER 6-1: 6.1.4.3 Returning a value of zero to the PC on an underflow has the effect of vectoring the program to the Reset vector, where the stack conditions can be verified and appropriate actions can be taken. This is not the same as a Reset, as the contents of the SFRs are not affected. PUSH and POP Instructions Since the Top-of-Stack is readable and writable, the ability to push values onto the stack and pull values off the stack, without disturbing normal program execution, is a desirable feature. The PIC18 instruction set includes two instructions, PUSH and POP, that permit the TOS to be manipulated under software control. TOSU, TOSH and TOSL can be modified to place data or a return address on the stack. The PUSH instruction places the current PC value onto the stack. This increments the Stack Pointer and loads the current PC value onto the stack. The POP instruction discards the current TOS by decrementing the Stack Pointer. The previous value pushed onto the stack then becomes the TOS value. STKPTR: STACK POINTER REGISTER R/C-0 R/C-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 STKFUL(1) STKUNF(1) — SP4 SP3 SP2 SP1 SP0 bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 STKFUL: Stack Full Flag bit(1) 1 = Stack has become full or overflowed 0 = Stack has not become full or overflowed bit 6 STKUNF: Stack Underflow Flag bit(1) 1 = Stack underflow has occurred 0 = Stack underflow did not occur bit 5 Unimplemented: Read as ‘0’ bit 4-0 SP: Stack Pointer Location bits Note 1: x = Bit is unknown Bit 7 and bit 6 are cleared by user software or by a POR. DS30000575C-page 120  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 6.1.4.4 Stack Full and Underflow Resets Device Resets on stack overflow and stack underflow conditions are enabled by setting the STVREN bit (CONFIG1L). When STVREN is set, a full or underflow condition will set the appropriate STKFUL or STKUNF bit and then cause a device Reset. When STVREN is cleared, a full or underflow condition will set the appropriate STKFUL or STKUNF bit, but not cause a device Reset. The STKFUL or STKUNF bits are cleared by user software or a Power-on Reset. 6.1.5 FAST REGISTER STACK A Fast Register Stack is provided for the STATUS, WREG and BSR registers to provide a “fast return” option for interrupts. This stack is only one level deep and is neither readable nor writable. It is loaded with the current value of the corresponding register when the processor vectors for an interrupt. All interrupt sources will push values into the Stack registers. The values in the registers are then loaded back into the working registers if the RETFIE, FAST instruction is used to return from the interrupt. 6.1.6 LOOK-UP TABLES IN PROGRAM MEMORY There may be programming situations that require the creation of data structures, or look-up tables, in program memory. For PIC18 devices, look-up tables can be implemented in two ways: • Computed GOTO • Table Reads 6.1.6.1 Computed GOTO A computed GOTO is accomplished by adding an offset to the Program Counter. An example is shown in Example 6-2. A look-up table can be formed with an ADDWF PCL instruction and a group of RETLW nn instructions. The W register is loaded with an offset into the table before executing a call to that table. The first instruction of the called routine is the ADDWF PCL instruction. The next instruction executed will be one of the RETLW nn instructions that returns the value, ‘nn’, to the calling function. If both low and high-priority interrupts are enabled, the Stack registers cannot be used reliably to return from low-priority interrupts. If a high-priority interrupt occurs while servicing a low-priority interrupt, the Stack register values stored by the low-priority interrupt will be overwritten. In these cases, users must save the key registers in software during a low-priority interrupt. The offset value (in WREG) specifies the number of bytes that the Program Counter should advance and should be multiples of two (LSb = 0). If interrupt priority is not used, all interrupts may use the Fast Register Stack for returns from interrupt. If no interrupts are used, the Fast Register Stack can be used to restore the STATUS, WREG and BSR registers at the end of a subroutine call. To use the Fast Register Stack for a subroutine call, a CALL label, FAST instruction must be executed to save the STATUS, WREG and BSR registers to the Fast Register Stack. A RETURN, FAST instruction is then executed to restore these registers from the Fast Register Stack. EXAMPLE 6-2: Example 6-1 shows a source code example that uses the Fast Register Stack during a subroutine call and return. EXAMPLE 6-1: CALL SUB1, FAST FAST REGISTER STACK CODE EXAMPLE ;STATUS, WREG, BSR ;SAVED IN FAST REGISTER ;STACK     RETURN FAST SUB1 ;RESTORE VALUES SAVED ;IN FAST REGISTER STACK  2012-2016 Microchip Technology Inc. In this method, only one data byte may be stored in each instruction location and room on the return address stack is required. ORG TABLE 6.1.6.2 MOVF CALL nn00h ADDWF RETLW RETLW RETLW . . . COMPUTED GOTO USING AN OFFSET VALUE OFFSET, W TABLE PCL nnh nnh nnh Table Reads A better method of storing data in program memory allows two bytes of data to be stored in each instruction location. Look-up table data may be stored, two bytes per program word, while programming. The Table Pointer (TBLPTR) specifies the byte address and the Table Latch (TABLAT) contains the data that is read from the program memory. Data is transferred from program memory one byte at a time. The table read operation is discussed further in Section 7.1 “Table Reads and Table Writes”. DS30000575C-page 121 PIC18F97J94 FAMILY 6.2 PIC18 Instruction Cycle 6.2.1 6.2.2 An “Instruction Cycle” consists of four Q cycles, Q1 through Q4. The instruction fetch and execute are pipelined in such a manner that a fetch takes one instruction cycle, while the decode and execute take another instruction cycle. However, due to the pipelining, each instruction effectively executes in one cycle. If an instruction (such as GOTO) causes the Program Counter to change, two cycles are required to complete the instruction. (See Example 6-3.) CLOCKING SCHEME The microcontroller clock input, whether from an internal or external source, is internally divided by four to generate four non-overlapping quadrature clocks (Q1, Q2, Q3 and Q4). Internally, the Program Counter is incremented on every Q1, with the instruction fetched from the program memory and latched into the Instruction Register (IR) during Q4. The instruction is decoded and executed during the following Q1 through Q4. The clocks and instruction execution flow are shown in Figure 6-4. FIGURE 6-4: INSTRUCTION FLOW/PIPELINING A fetch cycle begins with the Program Counter (PC) incrementing in Q1. In the execution cycle, the fetched instruction is latched into the Instruction Register (IR) in cycle Q1. This instruction is then decoded and executed during the Q2, Q3 and Q4 cycles. Data memory is read during Q2 (operand read) and written during Q4 (destination write). CLOCK/INSTRUCTION CYCLE Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 Q1 Q2 Internal Phase Clock Q3 Q4 PC PC PC + 2 PC + 4 OSC2/CLKO (RC mode) Execute INST (PC – 2) Fetch INST (PC) EXAMPLE 6-3: 1. MOVLW 55h 4. BSF Execute INST (PC + 2) Fetch INST (PC + 4) INSTRUCTION PIPELINE FLOW TCY0 TCY1 Fetch 1 Execute 1 2. MOVWF PORTB 3. BRA Execute INST (PC) Fetch INST (PC + 2) SUB_1 PORTA, BIT3 (Forced NOP) 5. Instruction @ address SUB_1 Fetch 2 TCY2 TCY3 TCY4 TCY5 Execute 2 Fetch 3 Execute 3 Fetch 4 Flush (NOP) Fetch SUB_1 Execute SUB_1 All instructions are single cycle, except for any program branches. These take two cycles since the fetch instruction is “flushed” from the pipeline while the new instruction is being fetched and then executed. DS30000575C-page 122  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 6.2.3 INSTRUCTIONS IN PROGRAM MEMORY The program memory is addressed in bytes. Instructions are stored as two or four bytes in program memory. The Least Significant Byte of an instruction word is always stored in a program memory location with an even address (LSB = 0). To maintain alignment with instruction boundaries, the PC increments in steps of two and the LSB will always read ‘0’ (see Section 6.1.3 “Program Counter”). Figure 6-5 shows an example of how instruction words are stored in the program memory. FIGURE 6-5: The CALL and GOTO instructions have the absolute program memory address embedded into the instruction. Since instructions are always stored on word boundaries, the data contained in the instruction is a word address. The word address is written to PC which accesses the desired byte address in program memory. Instruction #2 in Figure 6-5 shows how the instruction, GOTO 0006h, is encoded in the program memory. Program branch instructions, which encode a relative address offset, operate in the same manner. The offset value stored in a branch instruction represents the number of single-word instructions that the PC will be offset by. For more details on the instruction set, see Section 29.0 “Instruction Set Summary”. INSTRUCTIONS IN PROGRAM MEMORY LSB = 1 LSB = 0 0Fh EFh F0h C1h F4h 55h 06h 00h 23h 56h Program Memory Byte Locations  6.2.4 Instruction 1: Instruction 2: MOVLW GOTO 055h 0006h Instruction 3: MOVFF 123h, 456h TWO-WORD INSTRUCTIONS The standard PIC18 instruction set has four, two-word instructions: CALL, MOVFF, GOTO and LSFR. In all cases, the second word of the instructions always has ‘1111’ as its four Most Significant bits. The other 12 bits are literal data, usually a data memory address. The use of ‘1111’ in the 4 MSbs of an instruction specifies a special form of NOP. If the instruction is executed in proper sequence, immediately after the first word, the data in the second word is accessed and EXAMPLE 6-4: Word Address  000000h 000002h 000004h 000006h 000008h 00000Ah 00000Ch 00000Eh 000010h 000012h 000014h used by the instruction sequence. If the first word is skipped, for some reason, and the second word is executed by itself, a NOP is executed instead. This is necessary for cases when the two-word instruction is preceded by a conditional instruction that changes the PC. Example 6-4 shows how this works. Note: For information on two-word instructions in the extended instruction set, see Section 6.5 “Program Memory and the Extended Instruction Set”. TWO-WORD INSTRUCTIONS CASE 1: Object Code Source Code 0110 0110 0000 0000 TSTFSZ REG1 1100 0001 0010 0011 MOVFF REG1, REG2 ; No, skip this word ADDWF REG3 ; continue code ; is RAM location 0? 1111 0100 0101 0110 0010 0100 0000 0000 ; is RAM location 0? ; Execute this word as a NOP CASE 2: Object Code Source Code 0110 0110 0000 0000 TSTFSZ REG1 1100 0001 0010 0011 MOVFF REG1, REG2 ; Yes, execute this word ADDWF REG3 1111 0100 0101 0110 0010 0100 0000 0000 ; 2nd word of instruction  2012-2016 Microchip Technology Inc. ; continue code DS30000575C-page 123 PIC18F97J94 FAMILY 6.3 Note: Data Memory Organization The operation of some aspects of data memory are changed when the PIC18 extended instruction set is enabled. See Section 6.6 “Data Memory and the Extended Instruction Set” for more information. The data memory in PIC18 devices is implemented as static RAM. Each register in the data memory has a 12bit address, allowing up to 4,096 bytes of data memory. The memory space is divided into as many as 16 banks that contain 256 bytes each. PIC18FXXJ94 devices implement all 16 banks, for a total of 4 Kbytes. Figure 6-6 and Figure 6-7 show the data memory organization for the devices. The data memory contains Special Function Registers (SFRs) and General Purpose Registers (GPRs). The SFRs are used for control and status of the controller and peripheral functions, while GPRs are used for data storage and scratchpad operations in the user’s application. Any read of an unimplemented location will read as ‘0’s. The instruction set and architecture allow operations across all banks. The entire data memory may be accessed by Direct, Indirect or Indexed Addressing modes. Addressing modes are discussed later in this section. To ensure that commonly used registers (select SFRs and select GPRs) can be accessed in a single cycle, PIC18 devices implement an Access Bank. This is a 256-byte memory space that provides fast access to select SFRs and the lower portion of GPR Bank 0 without using the Bank Select Register. For details on the Access RAM, see Section 6.3.2 “Access Bank”. 6.3.1 BANK SELECT REGISTER Large areas of data memory require an efficient addressing scheme to make it possible for rapid access to any address. Ideally, this means that an entire address does not need to be provided for each read or write operation. For PIC18 devices, this is accomplished with a RAM banking scheme. This divides the memory space into 16 contiguous banks of 256 bytes. Depending on the instruction, each location can be addressed directly by its full 12-bit address, or an 8-bit, low-order address and a four-bit Bank Pointer. Most instructions in the PIC18 instruction set make use of the Bank Pointer, known as the Bank Select Register (BSR). This SFR holds the four Most Significant bits of a location’s address. The instruction itself includes the eight Least Significant bits. Only the four lower bits of the BSR are implemented (BSR). The upper four bits are unused, always read as ‘0’ and cannot be written to. The BSR can be loaded directly by using the MOVLB instruction. The value of the BSR indicates the bank in data memory. The eight bits in the instruction show the location in the bank and can be thought of as an offset from the bank’s lower boundary. The relationship between the BSR’s value and the bank division in data memory is shown in Figure 6-7. Since up to 16 registers may share the same low-order address, the user must always be careful to ensure that the proper bank is selected before performing a data read or write. For example, writing what should be program data to an 8-bit address of F9h, while the BSR is 0Fh, will end up resetting the Program Counter. While any bank can be selected, only those banks that are actually implemented can be read or written to. Writes to unimplemented banks are ignored, while reads from unimplemented banks will return ‘0’s. Even so, the STATUS register will still be affected as if the operation was successful. The data memory map in Figure 6-6 indicates which banks are implemented. In the core PIC18 instruction set, only the MOVFF instruction fully specifies the 12-bit address of the source and target registers. When this instruction executes, it ignores the BSR completely. All other instructions include only the low-order address as an operand and must use either the BSR or the Access Bank to locate their target registers. DS30000575C-page 124  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 6-6: DATA MEMORY MAP FOR PIC18F97J94 FAMILY DEVICES BSR Data Memory Map 00h = 0000 = 0001 = 0010 = 0011 = 0100 = 0101 = 0110 = 0111 = 1000 = 1001 = 1010 = 1011 = 1100 = 1101 = 1110 = 1111 Bank 0 FFh 00h Bank 1 GPR 1FFh 200h FFh 00h Bank 2 GPR FFh 00h Bank 3 2FFh 300h GPR FFh 00h Bank 4 3FFh 400h 6FFh 700h GPR FFh 00h 7FFh 800h GPR Bank 9 8FFh 900h The BSR specifies the bank used by the instruction. Access Bank Access RAM Low 00h 5Fh Access RAM High 60h (SFRs) FFh GPR 9FFh A00h FFh 00h Bank 13 When a = 1: GPR FFh 00h Bank 12 The second 160 bytes are Special Function Registers (from Bank 15). 5FFh 600h FFh 00h Bank 8 Bank 11 The first 96 bytes are general purpose RAM (from Bank 0). 4FFh 500h FFh 00h Bank 10 The BSR is ignored and the Access Bank is used. GPR Bank 5 Bank 7 When a = 0: GPR FFh 00h Bank 6 000h 05Fh 060h 0FFh 100h GPR FFh 00h FFh 00h FFh 00h FAh FFh 00h GPR GPR GPR GPR SFR SFR Bank 14 FFh 00h Bank 15 SFR FFh Note 1: Access RAM AFFh B00h BFFh C00h CFFh D00h DFAh DFFh E00h EFFh F00h F5Fh F60h FFFh Addresses, DFAh through F5Fh, are also SFRs, but are not part of the Access RAM. Users must always use the complete address, or load the proper BSR value, to access these registers.  2012-2016 Microchip Technology Inc. DS30000575C-page 125 PIC18F97J94 FAMILY FIGURE 6-7: USE OF THE BANK SELECT REGISTER (DIRECT ADDRESSING) BSR(1) 7 0 0 0 0 0 0 0 Bank Select(2) 1 0 000h Data Memory Bank 0 100h Bank 1 200h 300h Bank 2 00h 7 FFh 00h 1 From Opcode(2) 1 1 1 1 1 0 1 1 FFh 00h FFh 00h Bank 3 through Bank 13 E00h Bank 14 F00h FFFh Note 1: 2: 6.3.2 Bank 15 FFh 00h FFh 00h FFh The Access RAM bit of the instruction can be used to force an override of the selected bank (BSR) to the registers of the Access Bank. The MOVFF instruction embeds the entire 12-bit address in the instruction. ACCESS BANK While the use of the BSR, with an embedded 8-bit address, allows users to address the entire range of data memory, it also means that the user must ensure that the correct bank is selected. If not, data may be read from, or written to, the wrong location. This can be disastrous if a GPR is the intended target of an operation, but an SFR is written to instead. Verifying and/or changing the BSR for each read or write to data memory can become very inefficient. To streamline access for the most commonly used data memory locations, the data memory is configured with an Access Bank, which allows users to access a mapped block of memory without specifying a BSR. The Access Bank consists of the first 96 bytes of memory (00h-5Fh) in Bank 0 and the last 160 bytes of memory (60h-FFh) in Bank 15. The lower half is known as the “Access RAM” and is composed of GPRs. The upper half is where the device’s SFRs are mapped. These two areas are mapped contiguously in the Access Bank and can be addressed in a linear fashion by an 8-bit address (Figure 6-6). The Access Bank is used by core PIC18 instructions that include the Access RAM bit (the ‘a’ parameter in the instruction). When ‘a’ is equal to ‘1’, the instruction uses the BSR and the 8-bit address included in the opcode for the data memory address. When ‘a’ is ‘0’, however, the instruction is forced to use the Access Bank address map. In that case, the current value of the BSR is ignored entirely. DS30000575C-page 126 Using this “forced” addressing allows the instruction to operate on a data address in a single cycle without updating the BSR first. For 8-bit addresses of 60h and above, this means that users can evaluate and operate on SFRs more efficiently. The Access RAM below 60h is a good place for data values that the user might need to access rapidly, such as immediate computational results or common program variables. Access RAM also allows for faster and more code efficient context saving and switching of variables. The mapping of the Access Bank is slightly different when the extended instruction set is enabled (XINST Configuration bit = 1). This is discussed in more detail in Section 6.6.3 “Mapping the Access Bank in Indexed Literal Offset Mode”. 6.3.3 GENERAL PURPOSE REGISTER FILE PIC18 devices may have banked memory in the GPR area. This is data RAM which is available for use by all instructions. GPRs start at the bottom of Bank 0 (address 000h) and grow upwards towards the bottom of the SFR area. GPRs are not initialized by a Power-on Reset and are unchanged on all other Resets.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 6.3.4 SPECIAL FUNCTION REGISTERS The Special Function Registers (SFRs) are registers used by the CPU and peripheral modules for controlling the desired operation of the device. These registers are implemented as static RAM. SFRs start at the top of data memory (FFFh) and extend downward to occupy all of Bank 15 (F00h to FFFh), Bank 14 (E00h to EFFh) and part of Bank 13 (DFAh to DFFh). A list of these registers is given in Table 6-2.  2012-2016 Microchip Technology Inc. The SFRs can be classified into two sets: those associated with the “core” device functionality (ALU, Resets and interrupts) and those related to the peripheral functions. The Reset and Interrupt registers are described in their respective chapters, while the ALU’s STATUS register is described later in this section. Registers related to the operation of the peripheral features are described in the chapter for that peripheral. The SFRs are typically distributed among the peripherals whose functions they control. Unused SFR locations are unimplemented and read as ‘0’s. DS30000575C-page 127 PIC18F97J94 FAMILY TABLE 6-2: REGISTER FILE SUMMARY File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 — — — Top-of-Stack Upper Byte (TOS) Bit 1 Bit 0 FFFh TOSU FFEh TOSH Top-of-Stack High Byte (TOS) FFDh TOSL Top-of-Stack Low Byte (TOS) FFCh STKPTR STKFUL STKUNF — STKPTR FFBh PCLATU — — — Holding Register for PC FFAh PCLATH Holding Register for PC FF9h PCL PC Low Byte (PC) FF8h TBLPTRU FF7h TBLPTRH FF6h TBLPTRL Program Memory Table Pointer Low Byte (TBLPTR) FF5h TABLAT Program Memory Table Latch FF4h PRODH Product Register High Byte FF3h PRODL Product Register Low Byte FF2h INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE IOCIE TMR0IF INT0IF IOCIF FF1h INTCON2 RBPU INTEDG0 INTEDG1 INTEDG2 INTEDG3 TMR0IP INT3IP IOCIP FF0h INTCON3 INT2IP INT1IP INT3IE INT2IE INT1IE INT3IF INT2IF INT1IF FEFh INDF0 Uses contents of FSR0 to address data memory – value of FSR0 not changed (not a physical register) FEEh POSTINC0 Uses contents of FSR0 to address data memory – value of FSR0 post-incremented (not a physical register) — — ACSS Program Memory Table Pointer Upper Byte (TBLPTR) Program Memory Table Pointer High Byte (TBLPTR) FEDh POSTDEC0 Uses contents of FSR0 to address data memory – value of FSR0 post-decremented (not a physical register) FECh PREINC0 Uses contents of FSR0 to address data memory – value of FSR0 pre-incremented (not a physical register) FEBh PLUSW0 Uses contents of FSR0 to address data memory – value of FSR0 pre-incremented (not a physical register) – value of FSR0 offset by W FEAh FSR0H FE9h FSR0L — — — — Indirect Data Memory Address Pointer 0 High Indirect Data Memory Address Pointer 0 Low Byte FE8h WREG Working Register FE7h INDF1 Uses contents of FSR1 to address data memory – value of FSR1 not changed (not a physical register) FE6h POSTINC1 Uses contents of FSR1 to address data memory – value of FSR1 post-incremented (not a physical register) FE5h POSTDEC1 Uses contents of FSR1 to address data memory – value of FSR1 post-decremented (not a physical register) FE4h PREINC1 Uses contents of FSR1 to address data memory – value of FSR1 pre-incremented (not a physical register) FE3h PLUSW1 Uses contents of FSR1 to address data memory – value of FSR1 pre-incremented (not a physical register) – value of FSR1 offset by W FE2h FSR1H FE1h FSR1L FE0h BSR FDFh INDF2 — — — — Indirect Data Memory Address Pointer 1 High — Bank Select Register Indirect Data Memory Address Pointer 1 Low Byte — — — Uses contents of FSR2 to address data memory – value of FSR2 not changed (not a physical register) FDEh POSTINC2 Uses contents of FSR2 to address data memory – value of FSR2 post-incremented (not a physical register) FDDh POSTDEC2 Uses contents of FSR2 to address data memory – value of FSR2 post-decremented (not a physical register) FDCh PREINC2 Uses contents of FSR2 to address data memory – value of FSR2 pre-incremented (not a physical register) FDBh PLUSW2 Uses contents of FSR2 to address data memory – value of FSR2 pre-incremented (not a physical register) – value of FSR2 offset by W FDAh FSR2H — — FD9h FSR2L FD8h STATUS FD7h TMR0H Timer0 Register High Byte FD6h TMR0L Timer0 Register Low Byte FD5h T0CON FD4h Unimplemented FD3h OSCCON FD2h FD1h FD0h — — Indirect Data Memory Address Pointer 2 High Indirect Data Memory Address Pointer 2 Low Byte — — — N OV Z DC C T0PS0 TMR0ON T08BIT T0CS1 T0CS0 PSA T0PS2 T0PS1 — — — — — — — — IDLEN COSC2 COSC1 COSC0 — NOSC2 NOSC1 NOSC0 IPR5 — ACTORSIP ACTLOCKIP TMR8IP — TMR6IP TMR5IP TMR4IP IOCF IOCF7 IOCF6 IOCF5 IOCF4 IOCF3 IOCF2 IOCF1 IOCF0 RCON IPEN — CM RI TO PD POR BOR Legend: — = unimplemented, read as ‘0’. DS30000575C-page 128  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 6-2: File Name FCFh REGISTER FILE SUMMARY (CONTINUED) Bit 7 Bit 6 TMR1H Timer1 Register High Byte FCEh TMR1L Timer1 Register Low Byte FCDh T1CON TMR1CS1 TMR1CS0 FCCh TMR2 Timer2 Register FCBh PR2 Timer2 Period Register FCAh T2CON — T2OUTPS3 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 T1CKPS1 T1CKPS0 SOSCEN T1SYNC RD16 TMR1ON T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0 FC9h SSP1BUF MSSP1 Receive Buffer/Transmit Register FC8h SSP1ADD MSSP1 Address Register in I2C Slave Mode. MSSP1 Baud Rate Reload Register in I2C Master Mode. FC7h SSP1STAT SMP CKE D/A P S R/W UA BF FC6h SSP1CON1 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 FC5h SSP1CON2 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN FC4h CMSTAT — — — — — C3OUT C2OUT C1OUT FC3h ADCBUF0H A/D Result Register 0 High Byte FC2h ADCBUF0L A/D Result Register 0 Low Byte FC1h ADCON1H ADON — — — — MODE12 FORM1 FORM0 FC0h ADCON1L SSRC3 SSRC2 SSRC1 SSRC0 — ASAM SAMP DONE FBFh CVRCONH — — — CVR4 CVR3 CVR2 CVR1 CVR0 FBEh CVRCONL CVREN CVROE CVRPSS1 CVRPSS0 — — — CVRNSS FBDh ECCP1AS ECCP1ASE ECCP1AS2 ECCP1AS1 ECCP1AS0 PSS1AC1 PSS1AC0 PSS1BD1 PSS1BD0 FBCh ECCP1DEL P1RSEN P1DC6 P1DC5 P1DC4 P1DC3 P1DC2 P1DC1 P1DC0 CCP1M0 FBBh CCPR1H Capture/Compare/PWM Register1 High Byte FBAh CCPR1L Capture/Compare/PWM Register1 Low Byte FB9h CCP1CON P1M1 P1M0 CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 FB8h PIR5 — ACTORSIF ACTLOCKIF TMR8IF — TMR6IF TMR5IF TMR4IF FB7h PIE5 — ACTORSIE ACTLOCKIE TMR8IE — TMR6IE TMR5IE TMR4IE FB6h IPR4 CCP10IP CCP9IP CCP8IP CCP7IP CCP6IP CCP5IP CCP4IP ECCP3IP FB5h PIR4 CCP10IF CCP9IF CCP8IF CCP7IF CCP6IF CCP5IF CCP4IF ECCP3IF FB4h PIE4 CCP10IE CCP9IE CCP8IE CCP7IE CCP6IE CCP5IE CCP4IE ECCP3IE FB3h TMR3H Timer3 Register High Byte FB2h TMR3L Timer3 Register Low Byte FB1h T3CON TMR3CS1 TMR3CS0 T3CKPS1 T3CKPS0 SOSCEN T3SYNC RD16 TMR3ON TMR3GE T3GPOL T3GTM T3GSPM T3GGO/T3DONE T3GVAL T3GSS1 T3GSS0 FB0h T3GCON FAFh SPBRG1 EUSART1 Baud Rate Generator FAEh RCREG1 EUSART1 Receive Register FADh TXREG1 EUSART1 Transmit Register FACh TXSTA1 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D FABh RCSTA1 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D FAAh T1GCON TMR1GE T1GPOL T1GTM T1GSPM T1GGO/T1DONE T1GVAL T1GSS1 T1GSS0 FA9h IPR6 RC4IP TX4IP RC3IP TX3IP — CMP3IP CMP2IP CMP1IP FA8h HLVDCON VDIRMAG BGVST IRVST HLVDEN HLVDL3 HLVDL2 HLVDL1 HLVDL0 FA7h PSPCON IBF OBF IBOV PSPMODE — — — — FA6h PIR6 RC4IF TX4IF RC3IF TX3IF — CMP3IF CMP2IF CMP1IF FA5h IPR3 TMR5GIP LCDIP RC2IP TX2IP CTMUIP CCP2IP CCP1IP RTCCIP FA4h PIR3 TMR5GIF LCDIF RC2IF TX2IF CTMUIF CCP2IF CCP1IF RTCCIF FA3h PIE3 TMR5GIE LCDIE RC2IE TX2IE CTMUIE CCP2IE CCP1IE RTCCIE FA2h IPR2 OSCFIP SSP2IP BCL2IP USBIP BCL1IP HLVDIP TMR3IP TMR3GIP FA1h PIR2 OSCFIF SSP2IF BCL2IF USBIF BCL1IF HLVDIF TMR3IF TMR3GIF FA0h PIE2 OSCFIE SSP2IE BCL2IE USBIE BCL1IE HLVDIE TMR3IE TMR3GIE F9Fh IPR1 PSPIP ADIP RC1IP TX1IP SSP1IP TMR1GIP TMR2IP TMR1IP F9Eh PIR1 PSPIF ADIF RC1IF TX1IF SSP1IF TMR1GIF TMR2IF TMR1IF F9Dh PIE1 PSPIE ADIE RC1IE TX1IE SSP1IE TMR1GIE TMR2IE TMR1IE Legend: — = unimplemented, read as ‘0’.  2012-2016 Microchip Technology Inc. DS30000575C-page 129 PIC18F97J94 FAMILY TABLE 6-2: REGISTER FILE SUMMARY (CONTINUED) File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 STRA F9Ch PSTR1CON CMPL1 CMPL0 — STRSYNC STRD STRC STRB F9Bh OSCTUNE — — TUN5 TUN4 TUN3 TUN2 TUN1 TUN0 F9Ah TRISJ TRISJ7 TRISJ6 TRISJ5 TRISJ4 TRISJ3 TRISJ2 TRISJ1 TRISJ0 F99h TRISH TRISH7 TRISH6 TRISH5 TRISH4 TRISH3 TRISH2 TRISH1 TRISH0 F98h TRISG TRISG7 TRISG6 — TRISG4 TRISG3 TRISG2 TRISG1 TRISG0 F97h TRISF TRISF7 TRISF6 TRISF5 — — TRISF2 — — F96h TRISE TRISE7 TRISE6 TRISE5 TRISE4 TRISE3 TRISE2 TRISE1 TRISE0 F95h TRISD TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 F94h TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 — — F93h TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 F92h TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 F91h LATJ LATJ7 LATJ6 LATJ5 LATJ4 LATJ3 LATJ2 LATJ1 LATJ0 F90h LATH LATH7 LATH6 LATH5 LATH4 LATH3 LATH2 LATH1 LATH0 LATG0 F8Fh LATG LATG7 LATG6 — LATG4 LATG3 LATG2 LATG1 F8Eh LATF LATF7 LATF6 LATF5 — — LATF2 — — F8Dh LATE LATE7 LATE6 LATE5 LATE4 LATE3 LATE2 LATE1 LATE0 F8Ch LATD LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0 F8Bh LATC LATC7 LATC6 LATC5 LATC4 LATC3 LATC2 — — F8Ah LATB LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 F89h LATA LATA7 LATA6 LATA5 LATA4 LATA3 LATA2 LATA1 LATA0 F88h PORTJ RJ7 RJ6 RJ5 RJ4 RJ3 RJ2 RJ1 RJ0 F87h PORTH RH7 RH6 RH5 RH4 RH3 RH2 RH1 RH0 RG0 F86h PORTG RG7 RG6 — RG4 RG3 RG2 RG1 F85h PORTF RF7 RF6 RF5 RF4 RF3 RF2 — — F84h PORTE RE7 RE6 RE5 RE4 RE3 RE2 RE1 RE0 F83h PORTD RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 F82h PORTC RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 F81h PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 F80h PORTA RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0 F7Fh EECON1 — — WWPROG FREE WRERR WREN WR — F7Eh EECON2 F7Dh RCON2 EXTR — SWDTEN — — — — — F7Ch RCON3 STKERR — — — VDDBOR VDDPOR VBPOR VBAT F7Bh RCON4 — — — SRETEN — DPSLP — PMSLP F7Ah UFRML FRM7 FRM6 FRM5 FRM4 FRM3 FRM2 FRM1 FRM0 F79h UFRMH — — — — — FRM10 FRM9 FRM8 F78h UIR — SOFIF STALLIF IDLEIF TRNIF ACTVIF UERRIF URSTIF EEPROM Control Register 2 (not a physical register) F77h UEIR BTSEF — — BTOEF DFN8EF CRC16EF CRC5EF PIDEF F76H USTAT — ENDP3 ENDP2 ENDP1 ENDP0 DIR PPBI — F75h UCON — PPBRST SE0 PKTDIS USBEN RESUME SUSPND — F74h UADDR — ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 F73h TRISVP TRISVP7 TRISVP6 TRISVP5 TRISVP4 TRISVP3 TRISVP2 TRISVP1 TRISVP0 F72h LATVP LATVP7 LATVP6 LATVP5 LATVP4 LATVP3 LATVP2 LATVP1 LATVP0 F71h PORTVP RVP7 RVP6 RVP5 RVP4 RVP3 RVP2 RVP1 RVP0 F70h TXADDRL F6Fh TXADDRH F6Eh RXADDRL F6Dh RXADDRH F6Ch DMABCL F6Bh DMABCH F6Ah TXBUF Legend: SPI DMA Transmit Data Pointer Low Byte — — — — SPI DMA Transmit Data Pointer High Byte — SPI DMA Receive Data Pointer High Byte SPI DMA Receive Data Pointer Low Byte — — — SPI DMA Byte Count Low Byte — — — — — — TXBUF7 TXBUF6 TXBUF5 TXBUF4 TXBUF3 TXBUF2 SPI DMA Byte Count High Byte TXBUF1 TXBUF0 — = unimplemented, read as ‘0’. DS30000575C-page 130  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 6-2: File Name REGISTER FILE SUMMARY (CONTINUED) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 DHEN F69h SSP1CON3 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN F68h SSP1MSK MSK7 MSK6 MSK5 MSK4 MSK3 MSK2 MSK1 MSK0 F67h BAUDCON1 ABDOVF RCIDL RXDTP TXCKP BRG16 IREN WUE ABDEN F66h OSCCON2 CLKLOCK IOLOCK LOCK — CF POSCEN SOSCGO — F65h OSCCON3 — — — — — IRCF2 IRCF1 IRCF0 F64h OSCCON4 CPDIV1 CPDIV0 PLLEN — — — — — F63h ACTCON ACTEN — ACTSIDL ACTSRC ACTLOCK ACTLOCKPOL ACTORS ACTORSPOL F62h WPUB WPUB7 WPUB6 WPUB5 WPUB4 WPUB3 WPUB2 WPUB1 WPUB0 F61h PIE6 RC4IE TX4IE RC3IE TX3IE — CMP3IE CMP2IE CMP1IE F60h DMACON1 SSCON1 SSCON0 TXINC RXINC DUPLEX1 DUPLEX0 DLYINTEN DMAEN F5Fh RTCCON1 RTCEN — RTCWREN RTCSYNC HALFSEC RTCOE RTCPTR1 RTCPTR0 CAL7 CAL6 CAL5 CAL4 CAL3 CAL2 CAL1 CAL0 F5Eh RTCCAL F5Dh RTCVALH RTCC Value High Register Window Based on RTCPTR F5Ch RTCVALL RTCC Value Low Register Window Based on RTCPTR F5Bh ALRMCFG ALRMEN CHIME AMASK3 AMASK2 AMASK1 AMASK0 ALRMPTR1 ALRMPTR0 F5Ah ALRMRPT ARPT7 ARPT6 ARPT5 ARPT4 ARPT3 ARPT2 ARPT1 ARPT0 F59h ALRMVALH Alarm Value High Register Window Based on APTR F58h ALRMVALL Alarm Value Low Register Window Based on APTR F57h RTCCON2 PWCEN PWCPOL PWCCPRE PWCSPRE RTCCLKSEL1 F56h IOCP IOCP7 IOCP6 IOCP5 IOCP4 IOCP3 IOCP2 IOCP1 IOCP0 F55h IOCN IOCN7 IOCN6 IOCN5 IOCN4 IOCN3 IOCN2 IOCN1 IOCN0 F54h PADCFG1 RDPU REPU RFPU RGPU RHPU RJPU RKPU RLPU F53h CM1CON CON COE CPOL EVPOL1 EVPOL0 CREF CCH1 CCH0 F52h ECCP2AS ECCP2ASE ECCP2AS2 ECCP2AS1 ECCP2AS0 PSS2AC1 PSS2AC0 PSS2BD1 PSS2BD0 F51h ECCP2DEL P2RSEN P2DC6 P2DC5 P2DC4 P2DC3 P2DC2 P2DC1 P2DC0 F50h CCPR2H Capture/Compare/PWM Register 1 High Byte F4Fh CCPR2L Capture/Compare/PWM Register 1 Low Byte F4Eh CCP2CON P2M1 P2M0 CCP2X CCP2Y CCP2M3 CCP2M2 CCP2M1 CCP2M0 F4Dh ECCP3AS ECCP3ASE ECCP3AS2 ECCP3AS1 ECCP3AS0 PSS3AC1 PSS3AC0 PSS3BD1 PSS3BD0 F4Ch ECCP3DEL P3RSEN P3DC6 P3DC5 P3DC4 P3DC3 P3DC2 P3DC1 P3DC0 F4Bh CCPR3H Capture/Compare/PWM Register 1 High Byte F4Ah CCPR3L Capture/Compare/PWM Register 1 Low Byte F49H CCP3CON CCP3Y CCP3M3 CCP3M2 CCP3M1 CCP3M0 F48h CCPR8H Capture/Compare/PWM Register 8 High Byte F47h CCPR8L Capture/Compare/PWM Register 8 Low Byte F46h CCP8CON CCP8Y CCP8M3 CCP8M2 CCP8M1 CCP8M0 F45h CCPR9H Capture/Compare/PWM Register 9 High Byte F44h CCPR9L Capture/Compare/PWM Register 9 Low Byte F43h CCP9CON CCP9Y CCP9M3 CCP9M2 CCP9M1 CCP9M0 F42h CCPR10H Capture/Compare/PWM Register 10 High Byte F41h CCPR10L Capture/Compare/PWM Register 10 Low Byte F40h CCP10CON CCP10X CCP10Y CCP10M3 CCP10M2 CCP10M1 CCP10M0 F3Fh TMR6 Timer6 Register F3Eh PR6 Timer6 Period Register F3Dh T6CON T6OUTPS2 T6OUTPS1 T6OUTPS0 TMR6ON T6CKPS1 T6CKPS0 F3Ch TMR8 Timer8 Register F3Bh PR8 Timer8 Period Register F3Ah T8CON F39H SSP2CON3 F38h F37h P3M1 P3M0 — — — — — — — T6OUTPS3 CCP3X CCP8X CCP9X RTCCLKSEL0 RTCSECSEL1 RTCSECSEL0 — T8OUTPS3 T8OUTPS2 T8OUTPS1 T8OUTPS0 TMR8ON T8CKPS1 T8CKPS0 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN CM2CON CON COE CPOL EVPOL1 EVPOL0 CREF CCH1 CCH0 CM3CON CON COE CPOL EVPOL1 EVPOL0 CREF CCH1 CCH0 Legend: — = unimplemented, read as ‘0’.  2012-2016 Microchip Technology Inc. DS30000575C-page 131 PIC18F97J94 FAMILY TABLE 6-2: REGISTER FILE SUMMARY (CONTINUED) File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 F36h CCPTMRS0 C3TSEL1 C3TSEL0 C2TSEL2 C2TSEL1 C2TSEL0 C1TSEL2 C1TSEL1 C1TSEL0 F35h CCPTMRS1 C7TSEL1 C7TSEL0 — C6TSEL0 — C5TSEL0 C4TSEL1 C4TSEL0 F34h CCPTMRS2 — — — C10TSEL0 — C9TSEL0 C8TSEL1 C8TSEL0 F33h RCSTA2 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D F32h TXSTA2 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D F31h BAUDCON2 ABDOVF RCIDL RXDTP TXCKP BRG16 IREN WUE ABDEN F30h SPBRGH1 F2Fh RCSTA3 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D F2Eh TXSTA3 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D F2Dh BAUDCON3 ABDOVF RCIDL RXDTP TXCKP BRG16 IREN WUE ABDEN F2Ch SPBRGH3 EUSART3 Baud Rate Generator High Byte F2Bh SPBRG3 EUSART3 Baud Rate Generator EUSART1 Baud Rate Generator High Byte F2Ah RCREG3 EUSART3 Receive Data FIFO F29H TXREG3 EUSART3 Transmit Data FIFO F28h DSCONL — — — — — ULPWDIS DSBOR RELEASE F27h DSCONH DSEN — — — — — — RTCWDIS F26h DSWAKEL DSFLT BOR DSULP DSWDT DSRTC DSMCLR DSICD DSPOR F25h DSWAKEH — — — — — — — DSINT0 F24h DSGPR0 Deep Sleep General Purpose Register 0 F23h DSGPR1 Deep Sleep General Purpose Register 1 F22h DSGPR2 Deep Sleep General Purpose Register 2 F21h DSGPR3 Deep Sleep General Purpose Register 3 F20h SPBRGH2 EUSART2 Baud Rate Generator High Byte F1Fh SPBRG2 EUSART2 Baud Rate Generator F1Eh RCREG2 Receive Data FIFO F1Dh TXREG2 Transmit Data FIFO F1Ch PSTR2CON CMPL1 CMPL0 — STRSYNC STRD STRC STRB STRA F1Bh PSTR3CON CMPL1 CMPL0 — STRSYNC STRD STRC STRB STRA F1Ah SSP2STAT SMP CKE D/A P S R/W UA BF F19h SSP2CON1 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 F18h SSP2CON2 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN F17h SSP2MSK MSK7 MSK6 MSK5 MSK4 MSK3 MSK2 MSK1 MSK0 F16h TMR5H Timer5 Register High Byte F15h TMR5L Timer5 Register Low Byte F14h T5CON F13h T5GCON F12h CCPR4H Capture/Compare/PWM Register 4 High Byte F11h CCPR4L Capture/Compare/PWM Register 4 Low Byte F10h CCP4CON F0Fh CCPR5H Capture/Compare/PWM Register 5 High Byte F0Eh CCPR5L Capture/Compare/PWM Register 5 Low Byte F0Dh CCP5CON F0Ch CCPR6H Capture/Compare/PWM Register 6 High Byte F0Bh CCPR6L Capture/Compare/PWM Register 6 Low Byte F0Ah CCP6CON F09h CCPR7H Capture/Compare/PWM Register 7 High Byte F08h CCPR7L Capture/Compare/PWM Register 7 Low Byte F07h CCP7CON F06h TMR4 Timer4 Register F05h PR4 Timer4 Period Register F04h T4CON Legend: TMR5CS1 TMR5CS0 T5CKPS1 T5CKPS0 SOSCEN T5SYNC RD16 TMR5ON TMR5GE T5GPOL T5GTM T5GSPM T5GGO/T5DONE T5GVAL T5GSS1 T5GSS0 DC4B0 CCP4M3 CCP4M2 CCP4M1 CCP4M0 DC5B0 CCP5M3 CCP5M2 CCP5M1 CCP5M0 DC6B0 CCP6M3 CCP6M2 CCP6M1 CCP6M0 DC7B1 DC7B0 CCP7M3 CCP7M2 CCP7M1 CCP7M0 T4OUTPS2 T4OUTPS1 T4OUTPS0 TMR4ON T4CKPS1 T4CKPS0 — — — — — — — — — T4OUTPS3 DC4B1 DC5B1 DC6B1 — = unimplemented, read as ‘0’. DS30000575C-page 132  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 6-2: File Name REGISTER FILE SUMMARY (CONTINUED) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 F03h SSP2BUF MSSP2 Receive Buffer/Transmit Register F02h SSP2ADD MSSP2 Address Register in I2C Slave Mode. MSSP1 Baud Rate Reload Register in I2C Master Mode. F01h ANCFG F00h DMACON2 Bit 1 Bit 0 — — — — — VBG6EN VBG2EN VBGEN DLYCYC3 DLYCYC2 DLYCYC1 DLYCYC0 INTLVL3 INTLVL2 INTLVL1 INTLVL0 RX9D EFFh RCSTA4 SPEN RX9 SREN CREN ADDEN FERR OERR EFEh TXSTA4 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D ABDOVF RCIDL RXDTP TXCKP BRG16 IREN WUE ABDEN EFDh BAUDCON4 EFCh SPBRGH4 EUSART4 Baud Rate Generator High Byte EFBh SPBRG4 EUSART4 Baud Rate Generator EFAh RCREG4 EUSART4 Receive Data FIFO EF9h TXREG4 EUSART4 Transmit Data FIFO EF8h CTMUCON1 CTMUEN — CTMUSIDL TGEN EDGEN EDGSEQEN IDISSEN TRIGEN EF7h CTMUCON2 ITRIM5 ITRIM4 ITRIM3 ITRIM2 ITRIM1 ITRIM0 IRNG1 IRNG0 EF6h CTMUCON3 EDG2EN EDG2POL EDG2SEL3 EDG2SEL2 EDG2SEL1 EDG2SEL0 — — EF5h CTMUCON4 EDG1EN EDG1POL EDG1SEL3 EDG1SEL2 EDG1SEL1 EDG1SEL0 EDG2STAT EDG1STAT ECCP3MD EF4h PMD0 CCP10MD CCP9MD CCP8MD CCP7MD CCP6MD CCP5MD CCP4MD EF3h PMD1 ECCP2MD ECCP1MD UART4MD UART3MD UART2MD UART1MD SSP2MD SSP1MD EF2h PMD2 TMR8MD TMR6MD TMR5MD TMR4MD TMR3MD TMR2MD TMR1MD TMR0MD EF1h PMD3 DSMMD CTMUMD ADCMD RTCCMD LCDMD PSPMD REFO1MD REFO2MD EF0h PMD4 CMP1MD CMP2MD CMP3MD USBMD IOCMD LVDMD — EMBMD EEFh MDCON MDEN MDOE MDSLR MDOPOL MDO — — MDBIT MDSODIS — — — MDSRC3 MDSRC2 MDSRC1 MDSRC0 EEDh MDCARH MDCHODIS MDCHPOL MDCHSYNC — MDCH3 MDCH2 MDCH1 MDCH0 EECh MDCARL MDCLODIS MDCLPOL MDCLSYNC — MDCL3 MDCL2 MDCL1 MDCL0 EEBh ODCON1 ECCP2OD ECCP1OD USART4OD USART3OD USART2OD USART1OD SSP2OD SSP1OD EEAh ODCON2 EEEh MDSRC CCP10OD CCP9OD CCP8OD CCP7OD CCP6OD CCP5OD CCP4OD ECCP3OD EE9h TRISK TRISK7 TRISK6 TRISK5 TRISK4 TRISK3 TRISK2 TRISK1 TRISK0 EE8h LATK LATK7 LATK6 LATK5 LATK4 LATK3 LATK2 LATK1 LATK0 EE7h PORTK RK7 RK6 RK5 RK4 RK3 RK2 RK1 RK0 EE6h TRISL TRISL7 TRISL6 TRISL5 TRISL4 TRISL3 TRISL2 TRISL1 TRISL0 EE5h LATL LATL7 LATL6 LATL5 LATL4 LATL3 LATL2 LATL1 LATL0 EE4h PORTL RL7 RL6 RL5 RL4 RL3 RL2 RL1 RL0 EE3h MEMCON EBDIS — WAIT1 WAIT0 — — WM1 WM0 EE2h REFO1CON ON — SIDL OE RSLP — DIVSWEN ACTIVE EE1h REFO1CON1 — — — — ROSEL3 ROSEL2 ROSEL1 ROSEL0 EE0h REFO1CON2 RODIV7 RODIV6 RODIV5 RODIV4 RODIV3 RODIV2 RODIV1 RODIV0 EDFh REFO1CON3 — RODIV14 RODIV13 RODIV12 RODIV11 RODIV10 RODIV9 RODIV8 EDEh REFO2CON ON — SIDL OE RSLP — DIVSWEN ACTIVE EDDh REFO2CON1 — — — — ROSEL3 ROSEL2 ROSEL1 ROSEL0 EDCh REFO2CON2 RODIV7 RODIV6 RODIV5 RODIV4 RODIV3 RODIV2 RODIV1 RODIV0 EDBh REFO2CON3 — RODIV14 RODIV13 RODIV12 RODIV11 RODIV10 RODIV9 RODIV8 WFT BIASMD LCDA WA LP3 LP2 LP1 LP0 LCDEN SLPEN WERR CS1 CS0 LMUX2 LMUX1 LMUX0 EDAh LCDPS ED9h LCDCON ED8h LCDREG CPEN — BIAS2 BIAS1 BIAS0 MODE13 CLKSEL1 CLKSEL0 ED7h LCDREF LCDIRE — LCDCST2 LCDCST1 LCDCST0 VLCD3PE VLCD2PE VLCD1PE ED6h LCDRL LRLAP1 LRLAP0 LRLBP1 LRLBP0 — LRLAT2 LRLAT1 LRLAT0 ED5h LCDSE7 SE63 SE62 SE61 SE60 SE59 SE58 SE57 SE56 ED4h LCDSE6 SE55 SE54 SE53 SE52 SE51 SE50 SE49 SE48 ED3h LCDSE5 SE47 SE46 SE45 SE44 SE43 SE42 SE41 SE40 ED2h LCDSE4 SE39 SE38 S37 SE36 SE35 SE34 SE33 SE32 ED1h LCDSE3 SE31 SE30 SE29 SE28 SE27 SE26 SE25 SE24 ED0h LCDSE2 SE23 SE22 SE21 SE20 SE19 SE18 SE17 SE16 Legend: — = unimplemented, read as ‘0’.  2012-2016 Microchip Technology Inc. DS30000575C-page 133 PIC18F97J94 FAMILY TABLE 6-2: REGISTER FILE SUMMARY (CONTINUED) File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ECFh LCDSE1 SE15 SE14 SE13 SE12 SE11 SE10 SE09 SE08 ECEh LCDSE0 SE07 SE06 SE05 SE04 SE03 SE02 SE01 SE00 ECDh LCDDATA63 S63C7 S62C7 S61C7 S60C7 S59C7 S58C7 S57C7 S56C7 ECCh LCDDATA62 S55C7 S54C7 S53C7 S52C7 S51C7 S50C7 S49C7 S48C7 ECBh LCDDATA61 S47C7 S46C7 S45C7 S44C7 S43C7 S42C7 S41C7 S40C7 ECAh LCDDATA60 S39C7 S38C7 S37C7 S36C7 S35C7 S34C7 S33C7 S32C7 EC9h LCDDATA59 S31C7 S30C7 S29C7 S28C7 S27C7 S26C7 S25C7 S24C7 EC8h LCDDATA58 S23C7 S22C7 S21C7 S20C7 S19C7 S18C7 S17C7 S16C7 EC7h LCDDATA57 S15C7 S14C7 S13C7 S12C7 S11C7 S10C7 S09C7 S08C7 EC6h LCDDATA56 S07C7 S06C7 S05C7 S04C7 S03C7 S02C7 S01C7 S00C7 EC5h LCDDATA55 S63C6 S62C6 S61C6 S60C6 S59C6 S58C6 S57C6 S56C6 EC4h LCDDATA54 S55C6 S54C6 S53C6 S52C6 S51C6 S50C6 S49C6 S48C6 EC3h LCDDATA53 S47C6 S46C6 S45C6 S44C6 S43C6 S42C6 S41C6 S40C6 EC2h LCDDATA52 S39C6 S38C6 S37C6 S36C6 S35C6 S34C6 S33C6 S32C6 EC1h LCDDATA51 S31C6 S30C6 S29C6 S28C6 S27C6 S26C6 S25C6 S24C6 EC0h LCDDATA50 S23C6 S22C6 S21C6 S20C6 S19C6 S18C6 S17C6 S16C6 EBFh LCDDATA49 S15C6 S14C6 S13C6 S12C6 S11C6 S10C6 S09C6 S08C6 EBEh LCDDATA48 S07C6 S06C6 S05C6 S04C6 S03C6 S02C6 S01C6 S00C6 EBDh LCDDATA47 S63C5 S62C5 S61C5 S60C5 S59C5 S58C5 S57C5 S56C5 EBCh LCDDATA46 S55C5 S54C5 S53C5 S52C5 S51C5 S50C5 S49C5 S48C5 EBBh LCDDATA45 S47C5 S46C5 S45C5 S44C5 S43C5 S42C5 S41C5 S40C5 EBAh LCDDATA44 S39C5 S38C5 S37C5 S36C5 S35C5 S34C5 S33C5 S32C5 EB9h LCDDATA43 S31C5 S30C5 S29C5 S28C5 S27C5 S26C5 S25C5 S24C5 EB8h LCDDATA42 S23C5 S22C5 S21C5 S20C5 S19C5 S18C5 S17C5 S16C5 EB7h LCDDATA41 S15C5 S14C5 S13C5 S12C5 S11C5 S10C5 S09C5 S08C5 EB6h LCDDATA40 S07C5 S06C5 S05C5 S04C5 S03C5 S02C5 S01C5 S00C5 EB5h LCDDATA39 S63C4 S62C4 S61C4 S60C4 S59C4 S58C4 S57C4 S56C4 EB4h LCDDATA38 S55C4 S54C4 S53C4 S52C4 S51C4 S50C4 S49C4 S48C4 EB3h LCDDATA37 S47C4 S46C4 S45C4 S44C4 S43C4 S42C4 S41C4 S40C4 EB2h LCDDATA36 S39C4 S38C4 S37C4 S36C4 S35C4 S34C4 S33C4 S32C4 EB1h LCDDATA35 S31C4 S30C4 S29C4 S28C4 S27C4 S26C4 S25C4 S24C4 EB0h LCDDATA34 S23C4 S22C4 S21C4 S20C4 S19C4 S18C4 S17C4 S16C4 EAFh LCDDATA33 S15C4 S14C4 S13C4 S12C4 S11C4 S10C4 S09C4 S08C4 EAEh LCDDATA32 S07C4 S06C4 S05C4 S04C4 S03C4 S02C4 S01C4 S00C4 EADh LCDDATA31 S63C3 S62C3 S61C3 S60C3 S59C3 S58C3 S57C3 S56C3 EACh LCDDATA30 S55C3 S54C3 S53C3 S52C3 S51C3 S50C3 S49C3 S48C3 EABh LCDDATA29 S47C3 S46C3 S45C3 S44C3 S43C3 S42C3 S41C3 S40C3 EAAh LCDDATA28 S39C3 S38C3 S37C3 S36C3 S35C3 S34C3 S33C3 S32C3 EA9h LCDDATA27 S31C3 S30C3 S29C3 S28C3 S27C3 S26C3 S25C3 S24C3 EA8h LCDDATA26 S23C3 S22C3 S21C3 S20C3 S19C3 S18C3 S17C3 S16C3 EA7h LCDDATA25 S15C3 S14C3 S13C3 S12C3 S11C3 S10C3 S09C3 S08C3 EA6h LCDDATA24 S07C3 S06C3 S05C3 S04C3 S03C3 S02C3 S01C3 S00C3 EA5h LCDDATA23 S63C2 S62C2 S61C2 S60C2 S59C2 S58C2 S57C2 S56C2 EA4h LCDDATA22 S55C2 S54C2 S53C2 S52C2 S51C2 S50C2 S49C2 S48C2 EA3h LCDDATA21 S47C2 S46C2 S45C2 S44C2 S43C2 S42C2 S41C2 S40C2 EA2h LCDDATA20 S39C2 S38C2 S37C2 S36C2 S35C2 S34C2 S33C2 S32C2 EA1h LCDDATA19 S31C2 S30C2 S29C2 S28C2 S27C2 S26C2 S25C2 S24C2 EA0h LCDDATA18 S23C2 S22C2 S21C2 S20C2 S19C2 S18C2 S17C2 S16C2 E9Fh LCDDATA17 S15C2 S14C2 S13C2 S12C2 S11C2 S10C2 S09C2 S08C2 E9Eh LCDDATA16 S07C2 S06C2 S05C2 S04C2 S03C2 S02C2 S01C2 S00C2 E9Dh LCDDATA15 S63C1 S62C1 S61C1 S60C1 S59C1 S58C1 S57C1 S56C1 Legend: — = unimplemented, read as ‘0’. DS30000575C-page 134  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 6-2: REGISTER FILE SUMMARY (CONTINUED) File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 E9Ch LCDDATA14 S55C1 S54C1 S53C1 S52C1 S51C1 S50C1 S49C1 S48C1 E9Bh LCDDATA13 S47C1 S46C1 S45C1 S44C1 S43C1 S42C1 S41C1 S40C1 E9Ah LCDDATA12 S39C1 S38C1 S37C1 S36C1 S35C1 S34C1 S33C1 S32C1 E99h LCDDATA11 S31C1 S30C1 S29C1 S28C1 S27C1 S26C1 S25C1 S24C1 E98h LCDDATA10 S23C1 S22C1 S21C1 S20C1 S19C1 S18C1 S17C1 S16C1 E97h LCDDATA9 S15C1 S14C1 S13C1 S12C1 S11C1 S10C1 S09C1 S08C1 E96h LCDDATA8 S07C1 S06C1 S05C1 S04C1 S03C1 S02C1 S01C1 S00C1 E95h LCDDATA7 S63C0 S62C0 S61C0 S60C0 S59C0 S58C0 S57C0 S56C0 E94h LCDDATA6 S55C0 S54C0 S53C0 S52C0 S51C0 S50C0 S49C0 S48C0 E93h LCDDATA5 S47C0 S46C0 S45C0 S44C0 S43C0 S42C0 S41C0 S40C0 E92h LCDDATA4 S39C0 S38C0 S37C0 S36C0 S35C0 S34C0 S33C0 S32C0 E91h LCDDATA3 S31C0 S30C0 S29C0 S28C0 S27C0 S26C0 S25C0 S24C0 E90h LCDDATA2 S23C0 S22C0 S21C0 S20C0 S19C0 S18C0 S17C0 S16C0 E8Fh LCDDATA1 S15C0 S14C0 S13C0 S12C0 S11C0 S10C0 S09C0 S08C0 E8Eh LCDDATA0 S07C0 S06C0 S05C0 S04C0 S03C0 S02C0 S01C0 S00C0 E8Dh ADCON2H PVCFG1 PVCFG0 NVCFG0 OFFCAL BUFREGEN CSCNA — — E8Ch ADCON2L BUFS SMPI4 SMPI3 SMPI2 SMPI1 SMPI0 BUFM ALTS SAMC0 E8Bh ADCON3H ADRC EXTSAM PUMPEN SAMC4 SAMC3 SAMC2 SAMC1 E8Ah ADCON3L ADCS7 ADCS6 ADCS5 ADCS4 ADCS3 ADCS2 ADCS1 ADCS0 E89h ADCON5H ASENA LPENA CTMUREQ — — — ASINTMD1 ASINTMD0 E88h ADCON5L — — — — WM1 WM0 CM1 CM0 E87h ADCHS0H CH0NB2 CH0NB1 CH0NB0 CH0SB4 CH0SB3 CH0SB2 CH0SB1 CH0SB0 E86h ADCHS0L CH0NA2 CH0NA1 CH0NA0 CH0SA4 CH0SA3 CH0SA2 CH0SA1 CH0SA0 E85h ADCSS1H — CSS30 CSS29 CSS28 CSS27 CSS26 CSS25 CSS24 E84h ADCSS1L CSS23 CSS22 CSS21 CSS20 CSS19 CSS18 CSS17 CSS16 E83h ADCSS0H CSS15 CSS14 CSS13 CSS12 CSS11 CSS10 CSS9 CSS8 E82h ADCSS0L CSS7 CSS6 CSS5 CSS4 CSS3 CSS2 CSS1 CSS0 E81h ADCHIT1H — CHH30 CHH29 CHH28 CHH27 CHH26 CHH25 CHH24 CHH16 E80h ADCHIT1L CHH23 CHH22 CHH21 CHH20 CHH19 CHH18 CHH17 E7Fh ADCHIT0H CHH15 CHH14 CHH13 CHH12 CHH11 CHH10 CHH9 CHH8 E7Eh ADCHIT0L CHH7 CHH6 CHH5 CHH4 CHH3 CHH2 CHH1 CHH0 E7Dh ADCTMUEN1H — CTMUEN30 CTMUEN29 CTMUEN28 CTMUEN27 CTMUEN26 CTMUEN25 CTMUEN24 E7Ch ADCTMUEN1L CTMUEN23 CTMUEN22 CTMUEN21 CTMUEN20 CTMUEN19 CTMUEN18 CTMUEN17 CTMUEN16 E7Bh ADCTMUEN0H CTMUEN15 CTMUEN14 CTMUEN13 CTMUEN12 CTMUEN11 CTMUEN10 CTMUEN9 CTMUEN8 E7Ah ADCTMUEN0L CTMUEN7 CTMUEN6 CTMUEN5 CTMUEN4 CTMUEN3 CTMUEN2 CTMUEN1 CTMUEN0 E79h ADCBUF25H A/D Result Register 25 High Byte E78h ADCBUF25L A/D Result Register 25 Low Byte E77h ADCBUF24H A/D Result Register 24 High Byte E76h ADCBUF24L A/D Result Register 24 Low Byte E75h ADCBUF23H A/D Result Register 23 High Byte E74h ADCBUF23L A/D Result Register 23 Low Byte E73h ADCBUF22H A/D Result Register 22 High Byte E72h ADCBUF22L A/D Result Register 22 Low Byte E71h ADCBUF21H A/D Result Register 21 High Byte E70h ADCBUF21L A/D Result Register 21 Low Byte E6Fh ADCBUF20H A/D Result Register 20 High Byte E6Eh ADCBUF20L A/D Result Register 20 Low Byte E6Dh ADCBUF19H A/D Result Register 19 High Byte E6Ch ADCBUF19L A/D Result Register 19 Low Byte E6Bh ADCBUF18H A/D Result Register 18 High Byte E6Ah ADCBUF18L A/D Result Register 18 Low Byte Legend: — = unimplemented, read as ‘0’.  2012-2016 Microchip Technology Inc. DS30000575C-page 135 PIC18F97J94 FAMILY TABLE 6-2: REGISTER FILE SUMMARY (CONTINUED) File Name Bit 7 Bit 6 E69h ADCBUF17H E68h ADCBUF17L A/D Result Register 17 Low Byte E67h ADCBUF16H A/D Result Register 16 High Byte Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 A/D Result Register 17 High Byte E66h ADCBUF16L A/D Result Register 16 Low Byte E65h ADCBUF15H A/D Result Register 15 High Byte E64h ADCBUF15L A/D Result Register 15 Low Byte E63h ADCBUF14H A/D Result Register 14 High Byte E62h ADCBUF14L A/D Result Register 14 Low Byte E61h ADCBUF13H A/D Result Register 13 High Byte E60h ADCBUF13L A/D Result Register 13 Low Byte E5Fh ADCBUF12H A/D Result Register 12 High Byte E5Eh ADCBUF12L A/D Result Register 12 Low Byte E5Dh ADCBUF11H A/D Result Register 11 High Byte E5Ch ADCBUF11L A/D Result Register 11 Low Byte E5Bh ADCBUF10H A/D Result Register 10 High Byte E5Ah ADCBUF10L A/D Result Register 10 Low Byte E59h ADCBUF9H A/D Result Register 9 High Byte E58h ADCBUF9L A/D Result Register 9 Low Byte E57h ADCBUF8H A/D Result Register 8 High Byte E56h ADCBUF8L A/D Result Register 8 Low Byte E55h ADCBUF7H A/D Result Register 7 High Byte E54h ADCBUF7L A/D Result Register 7 Low Byte E53h ADCBUF6H A/D Result Register 6 High Byte E52h ADCBUF6L A/D Result Register 6 Low Byte E51h ADCBUF5H A/D Result Register 5 High Byte E50h ADCBUF5L A/D Result Register 5 Low Byte E4Fh ADCBUF4H A/D Result Register 4 High Byte E4Eh ADCBUF4L A/D Result Register 4 Low Byte E4Dh ADCBUF3H A/D Result Register 3 High Byte E4Ch ADCBUF3L A/D Result Register 3 Low Byte E4Bh ADCBUF2H A/D Result Register 2 High Byte E4Ah ADCBUF2L A/D Result Register 2 Low Byte E49h ADCBUF1H A/D Result Register 1 High Byte E48h ADCBUF1L A/D Result Register 1 Low Byte E47h ANCON1 ANSEL7 ANSEL6 ANSEL5 ANSEL4 ANSEL3 ANSEL2 ANSEL1 ANSEL0 E46h ANCON2 ANSEL15 ANSEL14 ANSEL13 ANSEL12 ANSEL11 ANSEL10 ANSEL9 ANSEL8 E45h ANCON3 ANSEL23 ANSEL22 ANSEL21 ANSEL20 ANSEL19 ANSEL18 ANSEL17 ANSEL16 E44h RPINR52_53 PBIO7R PBIO6R E43h RPINR50_51 PBIO5R PBIO4R E42h RPINR48_49 PBIO3R PBIO2R E41h RPINR46_47 PBIO1R PBIO0R E40h RPINR44_45 T5CKIR T5GR E3Fh RPINR42_43 T3CKIR T3GR E3Eh RPINR40_41 T1CKIR T1GR E3Dh RPINR38_39 T0CKIR CCP10R E3Ch RPINR36_37 CCP9R CCP8R E3Bh RPINR34_35 CCP7R CCP6R E3Ah RPINR32_33 CCP5R CCP4R E39h RPINR30_31 MDCIN2R MDCIN1R E38h RPINR28_29 MDMINR INT3R E37h RPINR26_27 INT2R INT1R Legend: — = unimplemented, read as ‘0’. DS30000575C-page 136  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 6-2: File Name REGISTER FILE SUMMARY (CONTINUED) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 E36h RPINR24_25 IOC7R IOC6R E35h RPINR22_23 IOC5R IOC4R E34h RPINR20_21 IOC3R IOC2R E33h RPINR18_19 IOC1R IOC0R E32h RPINR16_17 ECCP3R ECCP2R E31h RPINR14_15 ECCP1R FLT0R E30h RPINR12_13 SS2R SDI2R E2Fh RPINR10_11 SCK2R SS1R E2Eh RPINR8_9 SDI1R SCK1R E2Dh RPINR6_7 U4TXR U4RXR E2Ch RPINR4_5 U3TXR U3RXR E2Bh RPINR2_3 U2TXR U2RXR E2Ah RPINR0_1 E29h RPOR46 E28h RPOR44_45 RPO45R RPO44R E27h RPOR42_43 RPO43R RPO42R E26h RPOR40_41 RPO41R RPO40R E25h RPOR38_39 RPO39R RPO38R E24h RPOR36_37 RPO37R RPO36R E23h RPOR34_35 RPO35R RPO34R E22h RPOR32_33 RPO33R RPO32R E21h RPOR30_31 RPO31R RPO30R E20h RPOR28_29 RPO29R RPO28R E1Fh RPOR26_27 RPO27R RPO26R E1Eh RPOR24_25 RPO25R RPO24R E1Dh RPOR22_23 RPP23R RPO22R E1Ch RPOR20_21 RPO21R RPO20R E1Bh RPOR18_19 RPO19R RPO18R E1Ah RPOR16_17 RPO17R RPO16R E19h RPOR14_15 RPO15R RPO14R E18h RPOR12_13 RPO13R RPO12R E17h RPOR10_11 RPO11R RPO10R E16h RPOR8_9 RPO9R RPO8R E15h RPOR6_7 RPO7R RPO6R E14h RPOR4_5 RPO5R RPO4R E13h RPOR2_3 RPO3R RPO2R E12h RPOR0_1 RPO1R E11h UCFG E10h UIE U1TXR — — — Bit 0 U1RXR — RPO46R RPO0R UTEYE UOEMON — UPUEN UTRDIS FSEN PPB1 PPB0 — SOFIE STALLIE IDLEIE TRNIE ACTVIE UERRIE URSTIE E0Fh UEIE BTSEE — — BTOEE DFN8EE CRC16EE CRC5EE PIDEE E0Eh UEP15 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E0Dh UEP14 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E0Ch UEP13 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E0Bh UEP12 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E0Ah UEP11 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E09h UEP10 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E08h UEP9 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E07h UEP8 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E06h UEP7 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E05h UEP6 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E04h UEP5 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL Legend: — = unimplemented, read as ‘0’.  2012-2016 Microchip Technology Inc. DS30000575C-page 137 PIC18F97J94 FAMILY TABLE 6-2: REGISTER FILE SUMMARY (CONTINUED) File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 E03h UEP4 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E02h UEP3 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E01h UEP2 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL E00h UEP1 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL DFFh UEP0 — — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL DFEh Unimplemented — — — — — — — — DFDh Unimplemented — — — — — — — — DFCh Unimplemented — — — — — — — — DFBh Unimplemented — — — — — — — — DFAh — — — — — — — — Unimplemented Legend: — = unimplemented, read as ‘0’. DS30000575C-page 138  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 6.3.5 STATUS REGISTER The STATUS register, shown in Register 6-2, contains the arithmetic status of the ALU. The STATUS register can be the operand for any instruction, as with any other register. If the STATUS register is the destination for an instruction that affects the Z, DC, C, OV or N bits, the write to these five bits is disabled. These bits are set or cleared according to the device logic. Therefore, the result of an instruction with the STATUS register as destination may be different than intended. For example, CLRF STATUS will set the Z bit but leave the other bits unchanged. The STATUS register then reads back as ‘000u u1uu’. REGISTER 6-2: U-0 For other instructions not affecting any Status bits, see the instruction set summaries in Table 29-2 and Table 29-3. Note: The C and DC bits operate, in subtraction, as borrow and digit borrow bits, respectively. STATUS REGISTER U-0 — It is recommended, therefore, that only BCF, BSF, SWAPF, MOVFF and MOVWF instructions be used to alter the STATUS register because these instructions do not affect the Z, C, DC, OV or N bits in the STATUS register. — U-0 — R/W-x N R/W-x R/W-x R/W-x R/W-x Z DC(1) C(2) OV bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-5 Unimplemented: Read as ‘0’ bit 4 N: Negative bit This bit is used for signed arithmetic (2’s complement). It indicates whether the result was negative (ALU MSB = 1). 1 = Result was negative 0 = Result was positive bit 3 OV: Overflow bit This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the seven-bit magnitude which causes the sign bit (bit 7) to change state. 1 = Overflow occurred for signed arithmetic (in this arithmetic operation) 0 = No overflow occurred bit 2 Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1 DC: Digit Carry/Borrow bit(1) For ADDWF, ADDLW, SUBLW and SUBWF instructions: 1 = A carry-out from the 4th low-order bit of the result occurred 0 = No carry-out from the 4th low-order bit of the result bit 0 C: Carry/Borrow bit(2) For ADDWF, ADDLW, SUBLW and SUBWF instructions: 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred Note 1: 2: For borrow, the polarity is reversed. A subtraction is executed by adding the 2’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either bit 4 or bit 3 of the source register. For borrow, the polarity is reversed. A subtraction is executed by adding the 2’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low-order bit of the source register.  2012-2016 Microchip Technology Inc. DS30000575C-page 139 PIC18F97J94 FAMILY 6.4 Data Addressing Modes Note: The execution of some instructions in the core PIC18 instruction set are changed when the PIC18 extended instruction set is enabled. For more information, see Section 6.6 “Data Memory and the Extended Instruction Set”. While the program memory can be addressed in only one way, through the Program Counter, information in the data memory space can be addressed in several ways. For most instructions, the addressing mode is fixed. Other instructions may use up to three modes, depending on which operands are used and whether or not the extended instruction set is enabled. The addressing modes are: • • • • Inherent Literal Direct Indirect An additional addressing mode, Indexed Literal Offset, is available when the extended instruction set is enabled (XINST Configuration bit = 1). For details on this mode’s operation, see Section 6.6.1 “Indexed Addressing with Literal Offset”. 6.4.1 INHERENT AND LITERAL ADDRESSING Many PIC18 control instructions do not need any argument at all. They either perform an operation that globally affects the device or they operate implicitly on one register. This addressing mode is known as Inherent Addressing. Examples of this mode include SLEEP, RESET and DAW. Other instructions work in a similar way, but require an additional explicit argument in the opcode. This method is known as the Literal Addressing mode because the instructions require some literal value as an argument. Examples of this include ADDLW and MOVLW which, respectively, add or move a literal value to the W register. Other examples include CALL and GOTO, which include a 20-bit program memory address. 6.4.2 DIRECT ADDRESSING Direct Addressing specifies all or part of the source and/or destination address of the operation within the opcode itself. The options are specified by the arguments accompanying the instruction. In the core PIC18 instruction set, bit-oriented and byteoriented instructions use some version of Direct Addressing by default. All of these instructions include some 8-bit literal address as their Least Significant Byte. This address specifies the instruction’s data source as either a register address in one of the banks DS30000575C-page 140 of data RAM (see Section 6.3.3 “General Purpose Register File”) or a location in the Access Bank (see Section 6.3.2 “Access Bank”). The Access RAM bit, ‘a’, determines how the address is interpreted. When ‘a’ is ‘1’, the contents of the BSR (Section 6.3.1 “Bank Select Register”) are used with the address to determine the complete 12-bit address of the register. When ‘a’ is ‘0’, the address is interpreted as being a register in the Access Bank. Addressing that uses the Access RAM is sometimes also known as Direct Forced Addressing mode. A few instructions, such as MOVFF, include the entire 12-bit address (either source or destination) in their opcodes. In these cases, the BSR is ignored entirely. The destination of the operation’s results is determined by the destination bit, ‘d’. When ‘d’ is ‘1’, the results are stored back in the source register, overwriting its original contents. When ‘d’ is ‘0’, the results are stored in the W register. Instructions without the ‘d’ argument have a destination that is implicit in the instruction, either the target register being operated on or the W register. 6.4.3 INDIRECT ADDRESSING Indirect Addressing allows the user to access a location in data memory without giving a fixed address in the instruction. This is done by using File Select Registers (FSRs) as pointers to the locations to be read or written to. Since the FSRs are themselves located in RAM as Special Function Registers, they can also be directly manipulated under program control. This makes FSRs very useful in implementing data structures such as tables and arrays in data memory. The registers for Indirect Addressing are also implemented with Indirect File Operands (INDFs) that permit automatic manipulation of the pointer value with auto-incrementing, auto-decrementing or offsetting with another value. This allows for efficient code using loops, such as the example of clearing an entire RAM bank in Example 6-5. It also enables users to perform Indexed Addressing and other Stack Pointer operations for program memory in data memory. EXAMPLE 6-5: NEXT LFSR CLRF BTFSS BRA CONTINUE HOW TO CLEAR RAM (BANK 1) USING INDIRECT ADDRESSING FSR0, 100h ; POSTINC0 ; Clear INDF ; register then ; inc pointer FSR0H, 1 ; All done with ; Bank1? NEXT ; NO, clear next ; YES, continue  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 6.4.3.1 FSR Registers and the INDF Operand mapped in the SFR space, but are not physically implemented. Reading or writing to a particular INDF register actually accesses its corresponding FSR register pair. A read from INDF1, for example, reads the data at the address indicated by FSR1H:FSR1L. At the core of Indirect Addressing are three sets of registers: FSR0, FSR1 and FSR2. Each represents a pair of 8-bit registers: FSRnH and FSRnL. The four upper bits of the FSRnH register are not used, so each FSR pair holds a 12-bit value. This represents a value that can address the entire range of the data memory in a linear fashion. The FSR register pairs, then, serve as pointers to data memory locations. Instructions that use the INDF registers as operands actually use the contents of their corresponding FSR as a pointer to the instruction’s target. The INDF operand is just a convenient way of using the pointer. Because Indirect Addressing uses a full 12-bit address, data RAM banking is not necessary. Thus, the current contents of the BSR and the Access RAM bit have no effect on determining the target address. Indirect Addressing is accomplished with a set of Indirect File Operands, INDF0 through INDF2. These can be thought of as “virtual” registers. The operands are FIGURE 6-8: INDIRECT ADDRESSING 000h Using an instruction with one of the Indirect Addressing registers as the operand.... Bank 0 ADDWF, INDF1, 1 100h Bank 1 200h ...uses the 12-bit address stored in the FSR pair associated with that register.... 300h FSR1H:FSR1L 7 0 x x x x 1 1 1 1 7 Bank 2 0 1 1 0 0 1 1 0 0 Bank 3 through Bank 13 ...to determine the data memory location to be used in that operation. In this case, the FSR1 pair contains FCCh. This means the contents of location FCCh will be added to that of the W register and stored back in FCCh. E00h Bank 14 F00h FFFh Bank 15 Data Memory  2012-2016 Microchip Technology Inc. DS30000575C-page 141 PIC18F97J94 FAMILY 6.4.3.2 FSR Registers and POSTINC, POSTDEC, PREINC and PLUSW In addition to the INDF operand, each FSR register pair also has four additional indirect operands. Like INDF, these are “virtual” registers that cannot be indirectly read or written to. Accessing these registers actually accesses the associated FSR register pair, but also performs a specific action on its stored value. These operands are: • POSTDEC – Accesses the FSR value, then automatically decrements it by ‘1’ afterwards • POSTINC – Accesses the FSR value, then automatically increments it by ‘1’ afterwards • PREINC – Increments the FSR value by ‘1’, then uses it in the operation • PLUSW – Adds the signed value of the W register (range of -127 to 128) to that of the FSR and uses the new value in the operation In this context, accessing an INDF register uses the value in the FSR registers without changing them. Similarly, accessing a PLUSW register gives the FSR value, offset by the value in the W register, with neither value actually changed in the operation. Accessing the other virtual registers changes the value of the FSR registers. Operations on the FSRs with POSTDEC, POSTINC and PREINC affect the entire register pair. Rollovers of the FSRnL register, from FFh to 00h, carry over to the FSRnH register. On the other hand, results of these operations do not change the value of any flags in the STATUS register (for example, Z, N and OV bits). The PLUSW register can be used to implement a form of Indexed Addressing in the data memory space. By manipulating the value in the W register, users can reach addresses that are fixed offsets from pointer addresses. In some applications, this can be used to implement some powerful program control structure, such as software stacks, inside of data memory. DS30000575C-page 142 6.4.3.3 Operations by FSRs on FSRs Indirect Addressing operations that target other FSRs or virtual registers represent special cases. For example, using an FSR to point to one of the virtual registers will not result in successful operations. As a specific case, assume that the FSR0H:FSR0L registers contain FE7h, the address of INDF1. Attempts to read the value of the INDF1, using INDF0 as an operand, will return 00h. Attempts to write to INDF1, using INDF0 as the operand, will result in a NOP. On the other hand, using the virtual registers to write to an FSR pair may not occur as planned. In these cases, the value will be written to the FSR pair, but without any incrementing or decrementing. Thus, writing to INDF2 or POSTDEC2 will write the same value to the FSR2H:FSR2L. Since the FSRs are physical registers mapped in the SFR space, they can be manipulated through all direct operations. Users should proceed cautiously when working on these registers, however, particularly if their code uses Indirect Addressing. Similarly, operations by Indirect Addressing are generally permitted on all other SFRs. Users should exercise the appropriate caution, so that they do not inadvertently change settings that might affect the operation of the device. 6.5 Program Memory and the Extended Instruction Set The operation of program memory is unaffected by the use of the extended instruction set. Enabling the extended instruction set adds five additional two-word commands to the existing PIC18 instruction set: ADDFSR, CALLW, MOVSF, MOVSS and SUBFSR. These instructions are executed as described in Section 6.2.4 “Two-Word Instructions”.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 6.6 Data Memory and the Extended Instruction Set 6.6.2 INSTRUCTIONS AFFECTED BY INDEXED LITERAL OFFSET MODE Enabling the PIC18 extended instruction set (XINST Configuration bit = 1) significantly changes certain aspects of data memory and its addressing. Using the Access Bank for many of the core PIC18 instructions introduces a new addressing mode for the data memory space. This mode also alters the behavior of Indirect Addressing using FSR2 and its associated operands. Any of the core PIC18 instructions that can use Direct Addressing are potentially affected by the Indexed Literal Offset Addressing mode. This includes all byteoriented and bit-oriented instructions, or almost onehalf of the standard PIC18 instruction set. Instructions that only use Inherent or Literal Addressing modes are unaffected. What does not change is just as important. The size of the data memory space is unchanged, as well as its linear addressing. The SFR map remains the same. Core PIC18 instructions can still operate in both Direct and Indirect Addressing mode. Inherent and literal instructions do not change at all. Indirect Addressing with FSR0 and FSR1 also remains unchanged. Additionally, byte-oriented and bit-oriented instructions are not affected if they do not use the Access Bank (Access RAM bit = 1), or include a file address of 60h or above. Instructions meeting these criteria will continue to execute as before. A comparison of the different possible addressing modes when the extended instruction set is enabled is shown in Figure 6-9. 6.6.1 Those who desire to use byte-oriented or bit-oriented instructions in the Indexed Literal Offset mode should note the changes to assembler syntax for this mode. This is described in more detail in Section 29.2.1 “Extended Instruction Syntax”. INDEXED ADDRESSING WITH LITERAL OFFSET Enabling the PIC18 extended instruction set changes the behavior of Indirect Addressing using the FSR2 register pair and its associated file operands. Under the proper conditions, instructions that use the Access Bank – that is, most bit-oriented and byte-oriented instructions – can invoke a form of Indexed Addressing using an offset specified in the instruction. This special addressing mode is known as Indexed Addressing with Literal Offset or the Indexed Literal Offset mode. When using the extended instruction set, this addressing mode requires the following: • Use of the Access Bank (‘a’ = 0) • A file address argument that is less than or equal to 5Fh Under these conditions, the file address of the instruction is not interpreted as the lower byte of an address (used with the BSR in Direct Addressing) or as an 8-bit address in the Access Bank. Instead, the value is interpreted as an offset value to an Address Pointer specified by FSR2. The offset and the contents of FSR2 are added to obtain the target address of the operation.  2012-2016 Microchip Technology Inc. DS30000575C-page 143 PIC18F97J94 FAMILY FIGURE 6-9: COMPARING ADDRESSING OPTIONS FOR BIT-ORIENTED AND BYTEORIENTED INSTRUCTIONS (EXTENDED INSTRUCTION SET ENABLED) EXAMPLE INSTRUCTION: ADDWF, f, d, a (Opcode: 0010 01da ffff ffff) When a = 0 and f  60h: The instruction executes in Direct Forced mode. ‘f’ is interpreted as a location in the Access RAM between 060h and FFFh. This is the same as locations, F60h to FFFh (Bank 15), of data memory. Locations below 060h are not available in this addressing mode. 000h 060h Bank 0 100h 00h Bank 1 through Bank 14 F00h 60h Valid range for ‘f’ Access RAM FFh Bank 15 F40h SFRs FFFh When a = 0 and f5Fh: The instruction executes in Indexed Literal Offset mode. ‘f’ is interpreted as an offset to the address value in FSR2. The two are added together to obtain the address of the target register for the instruction. The address can be anywhere in the data memory space. Note that in this mode, the correct syntax is now: ADDWF [k], d where ‘k’ is the same as ‘f’. When a = 1 (all values of f): The instruction executes in Direct mode (also known as Direct Long mode). ‘f’ is interpreted as a location in one of the 16 banks of the data memory space. The bank is designated by the Bank Select Register (BSR). The address can be in any implemented bank in the data memory space. Data Memory 000h Bank 0 060h 100h 001001da ffffffff Bank 1 through Bank 14 FSR2H FSR2L F00h Bank 15 F40h SFRs FFFh Data Memory BSR 00000000 000h Bank 0 060h 100h Bank 1 through Bank 14 001001da ffffffff F00h Bank 15 F40h SFRs FFFh DS30000575C-page 144 Data Memory  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 6.6.3 MAPPING THE ACCESS BANK IN INDEXED LITERAL OFFSET MODE The use of Indexed Literal Offset Addressing mode effectively changes how the lower part of Access RAM (00h to 5Fh) is mapped. Rather than containing just the contents of the bottom part of Bank 0, this mode maps the contents from Bank 0 and a user-defined “window” that can be located anywhere in the data memory space. The value of FSR2 establishes the lower boundary of the addresses mapped into the window, while the upper boundary is defined by FSR2 plus 95 (5Fh). Addresses in the Access RAM above 5Fh are mapped as previously described. (See Section 6.3.2 “Access Bank”.) An example of Access Bank remapping in this addressing mode is shown in Figure 6-10. FIGURE 6-10: Remapping the Access Bank applies only to operations using the Indexed Literal Offset mode. Operations that use the BSR (Access RAM bit = 1) will continue to use Direct Addressing as before. Any Indirect or Indexed Addressing operation that explicitly uses any of the indirect file operands (including FSR2) will continue to operate as standard Indirect Addressing. Any instruction that uses the Access Bank, but includes a register address of greater than 05Fh, will use Direct Addressing and the normal Access Bank map. 6.6.4 BSR IN INDEXED LITERAL OFFSET MODE Although the Access Bank is remapped when the extended instruction set is enabled, the operation of the BSR remains unchanged. Direct Addressing, using the BSR to select the data memory bank, operates in the same manner as previously described. REMAPPING THE ACCESS BANK WITH INDEXED LITERAL OFFSET ADDRESSING Example Situation: ADDWF f, d, a FSR2H:FSR2L = 120h Locations in the region from the FSR2 Pointer (120h) to the pointer plus 05Fh (17Fh) are mapped to the bottom of the Access RAM (000h-05Fh). 000h 05Fh Bank 0 100h 120h 17Fh 200h Window Bank 1 00h Bank 1 “Window” 5Fh 60h Special Function Registers at F60h through FFFh are mapped to 60h through FFh, as usual. Bank 0 addresses below 5Fh are not available in this mode. They can still be addressed by using the BSR. Not Accessible Bank 2 through Bank 14 SFRs FFh Access Bank F00h Bank 15 F60h FFFh SFRs Data Memory  2012-2016 Microchip Technology Inc. DS30000575C-page 145 PIC18F97J94 FAMILY 7.0 FLASH PROGRAM MEMORY 7.1 Table Reads and Table Writes The Flash program memory is readable, writable and erasable during normal operation over the entire VDD range. In order to read and write program memory, there are two operations that allow the processor to move bytes between the program memory space and the data RAM: A read from program memory is executed on 1 byte at a time. A write to program memory is executed on blocks of 64 bytes at a time or 2 bytes at a time. Program memory is erased in blocks of 512 bytes at a time. A bulk erase operation may not be issued from user code. • Table Read (TBLRD) • Table Write (TBLWT) Writing or erasing program memory will cease instruction fetches until the operation is complete. The program memory cannot be accessed during the write or erase, therefore, code cannot execute. An internal programming timer terminates program memory writes and erases. A value written to program memory does not need to be a valid instruction. Executing a program memory location that forms an invalid instruction results in a NOP. The program memory space is 16 bits wide, while the data RAM space is 8 bits wide. Table reads and table writes move data between these two memory spaces through an 8-bit register (TABLAT). Table read operations retrieve data from program memory and place it into the data RAM space. Figure 7-1 shows the operation of a table read with program memory and data RAM. Table write operations store data from the data memory space into holding registers in program memory. The procedure to write the contents of the holding registers into program memory is detailed in Section 7.5 “Writing to Flash Program Memory”. Figure 7-2 shows the operation of a table write with program memory and data RAM. Table operations work with byte entities. A table block containing data, rather than program instructions, is not required to be word-aligned. Therefore, a table block can start and end at any byte address. If a table write is being used to write executable code into program memory, program instructions will need to be word-aligned. FIGURE 7-1: TABLE READ OPERATION Instruction: TBLRD* Program Memory Table Pointer(1) TBLPTRU TBLPTRH Table Latch (8-bit) TBLPTRL TABLAT Program Memory (TBLPTR) Note 1: Table Pointer register points to a byte in program memory. DS30000575C-page 146  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 7-2: TABLE WRITE OPERATION Instruction: TBLWT* Program Memory Holding Registers Table Pointer(1) TBLPTRU TBLPTRH Table Latch (8-bit) TBLPTRL TABLAT Program Memory (TBLPTR) Note 1: The Table Pointer actually points to one of 64 holding registers; the address of which is determined by TBLPTRL. The process for physically writing data to the program memory array is discussed in Section 7.5 “Writing to Flash Program Memory”. 7.2 Control Registers Several control registers are used in conjunction with the TBLRD and TBLWT instructions. These include: The WWPROG bit, when set, will allow programming two bytes per word on the execution of the WR command. If this bit is cleared, the WR command will result in programming on a block of 64 bytes. • • • • The FREE bit, when set, will allow a program memory erase operation. When FREE is set, the erase operation is initiated on the next WR command. When FREE is clear, only writes are enabled. EECON1 register EECON2 register TABLAT register TBLPTR registers 7.2.1 EECON1 AND EECON2 REGISTERS The EECON1 register (Register 7-1) is the control register for memory accesses. The EECON2 register is not a physical register; it is used exclusively in the memory write and erase sequences. Reading EECON2 will read all ‘0’s.  2012-2016 Microchip Technology Inc. The WREN bit, when set, will allow a write operation. On power-up, the WREN bit is clear. The WRERR bit is set in hardware when the WR bit is set, and cleared when the internal programming timer expires and the write operation is complete. Note: During normal operation, the WRERR is read as ‘1’. This can indicate that a write operation was prematurely terminated by a Reset or a write operation was attempted improperly. DS30000575C-page 147 PIC18F97J94 FAMILY Register 7-1: EECON1: EEPROM CONTROL REGISTER 1 (ACCESS FA6h) U-0 U-0 R/W-0 R/W-0 R/W-x R/W-0 R/S-0 U-0 — — WWPROG FREE WRERR(1) WREN WR — bit 7 bit 0 Legend: S = Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 Unimplemented: Read as ‘0’ bit 5 WWPROG: One Word-Wide Program bit 1 = Programs 2 bytes on the next WR command 0 = Programs 64 bytes on the next WR command bit 4 FREE: Flash Erase Enable bit 1 = Performs an erase operation on the next WR command (cleared by hardware after completion of erase) 0 = Performs write-only bit 3 WRERR: Flash Program Error Flag bit(1) 1 = A write operation is prematurely terminated (any Reset during self-timed programming in normal operation or an improper write attempt) 0 = The write operation completed bit 2 WREN: Flash Program Write Enable bit 1 = Allows write cycles to Flash program memory 0 = Inhibits write cycles to Flash program memory bit 1 WR: Write Control bit 1 = Initiates a program memory erase cycle or write cycle (the operation is self-timed and the bit is cleared by hardware once the write is complete) The WR bit can only be set (not cleared) in software. 0 = Write cycle is complete bit 0 Unimplemented: Read as ‘0’ Note 1: When a WRERR error occurs, the EEPGD and CFGS bits are not cleared. This allows tracing of the error condition. DS30000575C-page 148  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 7.2.2 TABLE LATCH REGISTER (TABLAT) 7.2.4 TABLE POINTER BOUNDARIES The Table Latch (TABLAT) is an 8-bit register mapped into the Special Function Register (SFR) space. The Table Latch register is used to hold 8-bit data during data transfers between program memory and data RAM. TBLPTR is used in reads, writes and erases of the Flash program memory. 7.2.3 When a TBLWT is executed, the seven Least Significant bits (LSbs) of the Table Pointer register (TBLPTR) determine which of the 64 program memory holding registers is written to. When the timed write to program memory begins (via the WR bit), the 12 Most Significant bits (MSbs) of the TBLPTR (TBLPTR) determine which program memory block of 1024 bytes is written to. For more detail, see Section 7.5 “Writing to Flash Program Memory”. When a TBLRD is executed, all 22 bits of the TBLPTR determine which byte is read from program memory into TABLAT. TABLE POINTER REGISTER (TBLPTR) The Table Pointer (TBLPTR) register addresses a byte within the program memory. The TBLPTR is comprised of three SFR registers: Table Pointer Upper Byte, Table Pointer High Byte and Table Pointer Low Byte (TBLPTRU:TBLPTRH:TBLPTRL). These three registers join to form a 22-bit wide pointer. The low-order 21 bits allow the device to address up to 2 Mbytes of program memory space. The 22nd bit allows access to the Device ID, the User ID and the Configuration bits. When an erase of program memory is executed, the 12 MSbs of the Table Pointer register point to the 1024-byte block that will be erased. The LSbs are ignored. The Table Pointer register, TBLPTR, is used by the TBLRD and TBLWT instructions. These instructions can update the TBLPTR in one of four ways, based on the table operation. These operations are shown in Table 7-1 and only affect the low-order 21 bits. TABLE 7-1: Figure 7-3 describes the relevant boundaries of the TBLPTR based on Flash program memory operations. TABLE POINTER OPERATIONS WITH TBLRD AND TBLWT INSTRUCTIONS Example Operation on Table Pointer TBLRD* TBLWT* TBLPTR is not modified TBLRD*+ TBLWT*+ TBLPTR is incremented after the read/write TBLRD*TBLWT*- TBLPTR is decremented after the read/write TBLRD+* TBLWT+* TBLPTR is incremented before the read/write FIGURE 7-3: 21 TABLE POINTER BOUNDARIES BASED ON OPERATION TBLPTRU 16 15 TBLPTRH 8 7 TBLPTRL 0 ERASE: TBLPTR TABLE WRITE: TBLPTR TABLE READ – TBLPTR  2012-2016 Microchip Technology Inc. DS30000575C-page 149 PIC18F97J94 FAMILY 7.3 Reading the Flash Program Memory The TBLPTR points to a byte address in program space. Executing TBLRD places the byte pointed to into TABLAT. In addition, the TBLPTR can be modified automatically for the next table read operation. The TBLRD instruction is used to retrieve data from program memory and places it into data RAM. Table reads from program memory are performed one byte at a time. The internal program memory is typically organized by words. The Least Significant bit of the address selects between the high and low bytes of the word. Figure 7-4 shows the interface between the internal program memory and the TABLAT. FIGURE 7-4: READS FROM FLASH PROGRAM MEMORY Program Memory (Even Byte Address) (Odd Byte Address) TBLPTR = xxxxx1 Instruction Register (IR) EXAMPLE 7-1: FETCH TBLPTR = xxxxx0 TABLAT Read Register TBLRD READING A FLASH PROGRAM MEMORY WORD MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF CODE_ADDR_UPPER TBLPTRU CODE_ADDR_HIGH TBLPTRH CODE_ADDR_LOW TBLPTRL ; Load TBLPTR with the base ; address of the word READ_WORD TBLRD*+ MOVF MOVWF TBLRD*+ MOVF MOVWF DS30000575C-page 150 TABLAT, W WORD_EVEN TABLAT, W WORD_ODD ; read into TABLAT and increment ; get data ; read into TABLAT and increment ; get data  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 7.4 Erasing Flash Program Memory The minimum erase block is 256 words or 512 bytes. Only through the use of an external programmer, or through ICSP control, can larger blocks of program memory be bulk erased. Word erase in the Flash array is not supported. When initiating an erase sequence from the microcontroller itself, a block of 512 bytes of program memory is erased. The Most Significant 12 bits of the TBLPTR point to the block being erased; TBLPTR are ignored. The EECON1 register commands the erase operation. The WREN bit must be set to enable write operations. The FREE bit is set to select an erase operation. For protection, the write initiate sequence for EECON2 must be used. 7.4.1 FLASH PROGRAM MEMORY ERASE SEQUENCE The sequence of events for erasing a block of internal program memory location is: 1. 2. 3. 4. 5. 6. 7. 8. Load Table Pointer register with address of row being erased. Set the WREN and FREE bits (EECON1) to enable the erase operation. Disable interrupts. Write 55h to EECON2. Write 0AAh to EECON2. Set the WR bit; this will begin the erase cycle. The CPU will stall for the duration of the erase for TIE (see Parameter D133B). Re-enable interrupts. A long write is necessary for erasing the internal Flash. Instruction execution is halted while in a long write cycle. The long write will be terminated by the internal programming timer. EXAMPLE 7-2: ERASING A FLASH PROGRAM MEMORY ROW MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF CODE_ADDR_UPPER TBLPTRU CODE_ADDR_HIGH TBLPTRH CODE_ADDR_LOW TBLPTRL ; load TBLPTR with the base ; address of the memory block BSF BSF BCF MOVLW MOVWF MOVLW MOVWF BSF BSF EECON1, EECON1, INTCON, 0x55 EECON2 0xAA EECON2 EECON1, INTCON, ; enable write to memory ; enable Row Erase operation ; disable interrupts ERASE_ROW Required Sequence  2012-2016 Microchip Technology Inc. WREN FREE GIE ; write 55h WR GIE ; write 0AAh ; start erase (CPU stall) ; re-enable interrupts DS30000575C-page 151 PIC18F97J94 FAMILY 7.5 Writing to Flash Program Memory The on-chip timer controls the write time. The write/ erase voltages are generated by an on-chip charge pump, rated to operate over the voltage range of the device. The programming block is 32 words or 64 bytes. Programming one word or 2 bytes at a time is also supported. Note 1: Unlike previous PIC® MCUs, devices of the PIC18FXXJ94 do not reset the holding registers after a write occurs. The holding registers must be cleared or overwritten before a programming sequence. Table writes are used internally to load the holding registers needed to program the Flash memory. There are 64 holding registers used by the table writes for programming. Since the Table Latch (TABLAT) is only a single byte, the TBLWT instruction may need to be executed 64 times for each programming operation (if WWPROG = 0). All of the table write operations will essentially be short writes because only the holding registers are written. At the end of updating the 64 holding registers, the EECON1 register must be written to in order to start the programming operation with a long write. 2: To maintain the endurance of the program memory cells, each Flash byte should not be programmed more than once between erase operations. Before attempting to modify the contents of the target cell a second time, an erase of the target page, or a bulk erase of the entire memory, must be performed. The long write is necessary for programming the internal Flash. Instruction execution is halted while in a long write cycle. The long write will be terminated by the internal programming timer. FIGURE 7-5: TABLE WRITES TO FLASH PROGRAM MEMORY TABLAT Write Register 8 8 TBLPTR = xxxxx0 Holding Register 8 TBLPTR = xxxxx2 TBLPTR = xxxxx1 Holding Register 8 TBLPTR = xxxx3F Holding Register Holding Register Program Memory 7.5.1 FLASH PROGRAM MEMORY WRITE SEQUENCE The sequence of events for programming an internal program memory location should be: 1. 2. 3. 4. 5. 6. 7. Read the 512 bytes into RAM. Update the data values in RAM as necessary. Load the Table Pointer register with the address being erased. Execute the erase procedure. Load the Table Pointer register with the address of the first byte being written, minus 1. Write the 64 bytes into the holding registers with auto-pre-increment. Set the WREN bit (EECON1) to enable byte writes. DS30000575C-page 152 8. 9. 10. 11. Disable the interrupts. Write 55h to EECON2. Write 0xAAh to EECON2. Set the WR bit. This will begin the write cycle. The CPU will stall for duration of the write for TIW (see Parameter D133A). 12. Re-enable the interrupts. 13. Verify the memory (table read). An example of the required code is shown in Example 7-3 on the following Page 153. Note: Before setting the WR bit, the Table Pointer address needs to be within the intended address range of the 64 bytes in the holding register.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY EXAMPLE 7-3: WRITING TO FLASH PROGRAM MEMORY MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF CODE_ADDR_UPPER TBLPTRU CODE_ADDR_HIGH TBLPTRH CODE_ADDR_LOW TBLPTRL ; Load TBLPTR with the base ; address of the memory block, minus 1 BSF BSF BCF MOVLW MOVWF MOVLW MOVWF BSF BSF MOVLW MOVWF EECON1, WREN EECON1, FREE INTCON, GIE 55h EECON2 0AAh EECON2 EECON1, WR INTCON, GIE D’8’ WRITE_COUNTER ; enable write to memory ; enable Erase operation ; disable interrupts MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF D'64' COUNTER BUFFER_ADDR_HIGH FSR0H BUFFER_ADDR_LOW FSR0L ERASE_BLOCK ; write 55h ; write 0AAh ; start erase (CPU stall) ; re-enable interrupts ; Need to write 8 blocks of 64 to write ; one erase block of 512 RESTART BUFFER ; point to buffer FILL_BUFFER ... ; read the new data from I2C, SPI, ; PSP, USART, etc. WRITE_BUFFER MOVLW MOVWF WRITE_BYTE_TO_HREGS MOVFF MOVWF TBLWT+* D’64 COUNTER ; number of bytes in holding register POSTINC0, WREG TABLAT ; ; ; ; ; DECFSZ COUNTER BRA WRITE_BYTE_TO_HREGS get low byte of buffer data present data to table latch write data, perform a short write to internal TBLWT holding register. loop until buffers are full PROGRAM_MEMORY Required Sequence BSF BCF MOVLW MOVWF MOVLW MOVWF BSF BSF BCF EECON1, INTCON, 55h EECON2 0AAh EECON2 EECON1, INTCON, EECON1, WREN GIE ; write 55h WR GIE WREN DECFSZ WRITE_COUNTER BRA RESTART_BUFFER  2012-2016 Microchip Technology Inc. ; enable write to memory ; disable interrupts ; ; ; ; write 0AAh start program (CPU stall) re-enable interrupts disable write to memory ; done with one write cycle ; if not done replacing the erase block DS30000575C-page 153 PIC18F97J94 FAMILY 7.5.2 FLASH PROGRAM MEMORY WRITE SEQUENCE (WORD PROGRAMMING) The PIC18FXXJ94 of devices has a feature that allows programming a single word (two bytes). This feature is enabled when the WWPROG bit is set. If the memory location is already erased, the following sequence is required to enable this feature: 1. 2. Load the Table Pointer register with the address of the data to be written. (It must be an even address.) Write the 2 bytes into the holding registers by performing table writes. (Do not post-increment on the second table write). EXAMPLE 7-4: 3. 4. 5. 6. 7. 8. 9. Set the WREN bit (EECON1) to enable writes and the WWPROG bit (EECON1) to select Word Write mode. Disable interrupts. Write 55h to EECON2. Write 0AAh to EECON2. Set the WR bit; this will begin the write cycle. The CPU will stall for the duration of the write for TIW (see Parameter D133A). Re-enable interrupts. SINGLE-WORD WRITE TO FLASH PROGRAM MEMORY MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF TBLWT*+ MOVLW MOVWF TBLWT* CODE_ADDR_UPPER TBLPTRU CODE_ADDR_HIGH TBLPTRH CODE_ADDR_LOW TBLPTRL DATA0 TABLAT ; Load TBLPTR with the base address DATA1 TABLAT ; MSB of word to be written BSF BSF BCF MOVLW MOVWF MOVLW MOVWF BSF BSF BCF BCF EECON1, EECON1, INTCON, 55h EECON2 0AAh EECON2 EECON1, INTCON, EECON1, EECON1, ; The table pointer must be loaded with an even address ; LSB of word to be written ; The last table write must not increment the table pointer! The table pointer needs to point to the MSB before starting the write operation. PROGRAM_MEMORY Required Sequence DS30000575C-page 154 WWPROG WREN GIE ; enable single word write ; enable write to memory ; disable interrupts ; write 55h WR GIE WWPROG WREN ; ; ; ; ; write AAh start program (CPU stall) re-enable interrupts disable single word write disable write to memory  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 7.5.3 WRITE VERIFY Depending on the application, good programming practice may dictate that the value written to the memory should be verified against the original value. This should be used in applications where excessive writes can stress bits near the specification limit. 7.5.4 7.6 Flash Program Operation During Code Protection See Section 28.4.5 “Program Verification and Code Protection” for details on code protection of Flash program memory. UNEXPECTED TERMINATION OF WRITE OPERATION If a write is terminated by an unplanned event, such as loss of power or an unexpected Reset, the memory location just programmed should be verified and reprogrammed if needed. If the write operation is interrupted by a MCLR Reset, or a WDT time-out Reset during normal operation, the user can check the WRERR bit and rewrite the location(s) as needed  2012-2016 Microchip Technology Inc. DS30000575C-page 155 PIC18F97J94 FAMILY 8.0 EXTERNAL MEMORY BUS Note: The External Memory Bus implemented on 64-pin devices. is not The External Memory Bus (EMB) allows the device to access external memory devices (such as Flash, EPROM or SRAM) as program or data memory. It supports both 8 and 16-Bit Data Width modes, and three address widths of up to 20 bits. TABLE 8-1: The bus is implemented with 28 pins, multiplexed across four I/O ports. Three ports (PORTD, PORTE and PORTH) are multiplexed with the address/data bus for a total of 20 available lines, while PORTJ is multiplexed with the bus control signals. A list of the pins and their functions is provided in Table 8-1. PIC18F97J94 FAMILY EXTERNAL BUS – I/O PORT FUNCTIONS Name Port Bit External Memory Bus Function RD0/AD0 PORTD 0 Address Bit 0 or Data Bit 0 RD1/AD1 PORTD 1 Address Bit 1 or Data Bit 1 RD2/AD2 PORTD 2 Address Bit 2 or Data Bit 2 RD3/AD3 PORTD 3 Address Bit 3 or Data Bit 3 RD4/AD4 PORTD 4 Address Bit 4 or Data Bit 4 RD5/AD5 PORTD 5 Address Bit 5 or Data Bit 5 RD6/AD6 PORTD 6 Address Bit 6 or Data Bit 6 RD7/AD7 PORTD 7 Address Bit 7 or Data Bit 7 RE0/AD8 PORTE 0 Address Bit 8 or Data Bit 8 RE1/AD9 PORTE 1 Address Bit 9 or Data Bit 9 RE2/AD10 PORTE 2 Address Bit 10 or Data Bit 10 RE3/AD11 PORTE 3 Address Bit 11 or Data Bit 11 RE4/AD12 PORTE 4 Address Bit 12 or Data Bit 12 RE5/AD13 PORTE 5 Address Bit 13 or Data Bit 13 RE6/AD14 PORTE 6 Address Bit 14 or Data Bit 14 RE7/AD15 PORTE 7 Address Bit 15 or Data Bit 15 RH0/A16 PORTH 0 Address Bit 16 RH1/A17 PORTH 1 Address Bit 17 RH2/A18 PORTH 2 Address Bit 18 RH3/A19 PORTH 3 Address Bit 19 RJ0/ALE PORTJ 0 Address Latch Enable (ALE) Control Pin RJ1/OE PORTJ 1 Output Enable (OE) Control Pin RJ2/WRL PORTJ 2 Write Low (WRL) Control Pin RJ3/WRH PORTJ 3 Write High (WRH) Control Pin RJ4/BA0 PORTJ 4 Byte Address Bit 0 (BA0) RJ5/CE PORTJ 5 Chip Enable (CE) Control Pin RJ6/LB PORTJ 6 Lower Byte Enable (LB) Control Pin RJ7/UB PORTJ 7 Upper Byte Enable (UB) Control Pin Note: For the sake of clarity, only I/O port and external bus assignments are shown here. One or more additional multiplexed features may be available on some pins. DS30000575C-page 156  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 8.1 External Memory Bus Control The operation of the interface is controlled by the MEMCON register (Register 8-1). This register is available in all program memory operating modes, except Microcontroller mode. In this mode, the register is disabled and cannot be written to. The EBDIS bit (MEMCON) controls the operation of the bus and related port functions. Clearing EBDIS enables the interface and disables the I/O functions of the ports, as well as any other functions multiplexed to those pins. Setting the bit enables the I/O ports and other functions, but allows the interface to override everything else on the pins when an external memory operation is required. By default, the external bus is always enabled and disables all other I/O. REGISTER 8-1: The operation of the EBDIS bit is also influenced by the program memory mode being used. This is discussed in more detail in Section 8.5 “Program Memory Modes and the External Memory Bus”. The WAITx bits allow for the addition of Wait states to external memory operations. The use of these bits is discussed in Section 8.3 “Wait States”. The WMx bits select the particular operating mode used when the bus is operating in 16-Bit Data Width mode. This is discussed in more detail in Section 8.6 “16-Bit Data Width Modes”. These bits have no effect when an 8-Bit Data Width mode is selected. MEMCON: EXTERNAL MEMORY BUS CONTROL REGISTER(1) R/W-0 U-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 EBDIS — WAIT1 WAIT0 — — WM1 WM0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 EBDIS: External Bus Disable bit 1 = External bus is enabled when microcontroller accesses external memory; otherwise, all external bus drivers are mapped as I/O ports 0 = External bus is always enabled, I/O ports are disabled bit 6 Unimplemented: Read as ‘0’ bit 5-4 WAIT: Table Reads and Writes Bus Cycle Wait Count bits 11 = Table reads and writes will wait 0 TCY 10 = Table reads and writes will wait 1 TCY 01 = Table reads and writes will wait 2 TCY 00 = Table reads and writes will wait 3 TCY bit 3-2 Unimplemented: Read as ‘0’ bit 1-0 WM: TBLWT Operation with 16-Bit Data Bus Width Select bits 1x = Word Write mode: TABLAT word output, WRH is active when TABLAT is written 01 = Byte Select mode: TABLAT data is copied on both MSB and LSB, WRH and (UB or LB) will activate 00 = Byte Write mode: TABLAT data is copied on both MSB and LSB, WRH or WRL will activate Note 1: This register is unimplemented on 64-pin devices, read as ‘0’.  2012-2016 Microchip Technology Inc. DS30000575C-page 157 PIC18F97J94 FAMILY 8.2 Address and Data Width 8.2.1 The PIC18FXXJ94 of devices can be independently configured for different address and data widths on the same memory bus. Both address and data width are set by Configuration bits in the CONFIG5L register. As Configuration bits, this means that these options can only be configured by programming the device and are not controllable in software. The BW bit selects an 8-bit or 16-bit data bus width. Setting this bit (default) selects a data width of 16 bits. The ABW bits determine both the program memory operating mode and the address bus width. The available options are 20-bit, 16-bit and 12-bit, as well as Microcontroller mode (external bus disabled). Selecting a 16-bit or 12-bit width makes a corresponding number of high-order lines available for I/O functions. These pins are no longer affected by the setting of the EBDIS bit. For example, selecting a 16Bit Addressing mode (ABW = 01) disables A and allows PORTH to function without interruptions from the bus. Using the smaller address widths allows users to tailor the memory bus to the size of the external memory space for a particular design while freeing up pins for dedicated I/O operation. Because the ABWx bits have the effect of disabling pins for memory bus operations, it is important to always select an address width at least equal to the data width. If a 12-bit address width is used with a 16bit data width, the upper four bits of data will not be available on the bus. All combinations of address and data widths require multiplexing of address and data information on the same lines. The address and data multiplexing, as well as I/O ports made available by the use of smaller address widths, are summarized in Table 8-2. TABLE 8-2: ADDRESS SHIFTING ON THE EXTERNAL BUS By default, the address presented on the external bus is the value of the PC. In practical terms, this means that addresses in the external memory device, below the top of on-chip memory, are unavailable to the microcontroller. To access these physical locations, the glue logic between the microcontroller and the external memory must somehow translate addresses. To simplify the interface, the external bus offers an extension of Extended Microcontroller mode that automatically performs address shifting. This feature is controlled by the EASHFT Configuration bit. Setting this bit offsets addresses on the bus by the size of the microcontroller’s on-chip program memory and sets the bottom address at 0000h. This allows the device to use the entire range of physical addresses of the external memory. 8.2.2 21-BIT ADDRESSING As an extension of 20-bit address width operation, the External Memory Bus can also fully address a 2-Mbyte memory space. This is done by using the Bus Address Bit 0 (BA0) control line as the Least Significant bit of the address. The UB and LB control signals may also be used with certain memory devices to select the upper and lower bytes within a 16-bit wide data word. This addressing mode is available in both 8-Bit and certain 16-Bit Data Width modes. Additional details are provided in Section 8.6.3 “16-Bit Byte Select Mode” and Section 8.7 “8-Bit Data Width Mode”. ADDRESS AND DATA LINES FOR DIFFERENT ADDRESS AND DATA WIDTHS Data Width Address Width Multiplexed Data and Address Lines (and Corresponding Ports) 12-bit 8-bit 16-bit AD (PORTD) 20-bit 16-bit 16-bit DS30000575C-page 158 20-bit AD (PORTD, PORTE) Address Only Lines (and Corresponding Ports) Ports Available for I/O AD (PORTE) PORTE, All of PORTH AD (PORTE) All of PORTH A, AD (PORTH, PORTE) — — All of PORTH A (PORTH) —  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 8.3 Wait States While it may be assumed that external memory devices will operate at the microcontroller clock rate, this is often not the case. In fact, many devices require longer times to write or retrieve data than the time allowed by the execution of table read or table write operations. To compensate for this, the External Memory Bus can be configured to add a fixed delay to each table operation using the bus. Wait states are enabled by setting the WAIT Configuration bit. When enabled, the amount of delay is set by the WAIT bits (MEMCON). The delay is based on multiples of microcontroller instruction cycle time and is added following the instruction cycle when the table operation is executed. The range is from no delay to 3 TCY (default value). 8.4 Port Pin Weak Pull-ups With the exception of the upper address lines, A, the pins associated with the External Memory Bus are equipped with weak pull-ups. The pull-ups are controlled by the upper nibble of the PADCFG register (PADCFG). They are named RDPU, REPU, RHPU and RJPU, and control pull-ups on PORTD, PORTE, PORTH and PORTJ, respectively. Setting one of these bits enables the corresponding pull-ups for that port. All pull-ups are disabled by default on all device Resets. functions. When EBDIS = 0, the pins function as the external bus. When EBDIS = 1, the pins function as I/O ports. If the device fetches or accesses external memory while EBDIS = 1, the pins will switch to the external bus. If the EBDIS bit is set by a program executing from external memory, the action of setting the bit will be delayed until the program branches into the internal memory. At that time, the pins will change from external bus to I/O ports. If the device is executing out of internal memory when EBDIS = 0, the memory bus address/data and control pins will not be active. They will go to a state where the active address/data pins are tri-state; the CE, OE, WRH, WRL, UB and LB signals are ‘1’, and ALE and BA0 are ‘0’. Note that only those pins associated with the current address width are forced to tri-state; the other pins continue to function as I/O. In the case of 16bit address width, for example, only AD (PORTD and PORTE) are affected; A (PORTH) continue to function as I/O. In all external memory modes, the bus takes priority over any other peripherals that may share pins with it. This includes the Parallel Master Port and serial communication modules which would otherwise take priority over the I/O port. 8.6 16-Bit Data Width Modes In Extended Microcontroller mode, the port pull-ups can be useful in preserving the memory state on the external bus while the bus is temporarily disabled (EBDIS = 1). In 16-Bit Data Width mode, the external memory interface can be connected to external memories in three different configurations: 8.5 • 16-Bit Byte Write • 16-Bit Word Write • 16-Bit Byte Select Program Memory Modes and the External Memory Bus The PIC18FXXJ94 of devices is capable of operating in one of two program memory modes, using combinations of on-chip and external program memory. The functions of the multiplexed port pins depend on the program memory mode selected, as well as the setting of the EBDIS bit. In Microcontroller Mode, the bus is not active and the pins have their port functions only. Writes to the MEMCOM register are not permitted. The Reset value of EBDIS (‘0’) is ignored and the ABWx pins behave as I/O ports. In Extended Microcontroller Mode, the external program memory bus shares I/O port functions on the pins. When the device is fetching or doing table read/ table write operations on the external program memory space, the pins will have the external bus function. If the device is fetching and accessing internal program memory locations only, the EBDIS control bit will change the pins from external memory to I/O port  2012-2016 Microchip Technology Inc. The configuration to be used is determined by the WM bits in the MEMCON register (MEMCON). These three different configurations allow the designer maximum flexibility in using both 8bit and 16-bit devices with 16-bit data. For all 16-bit modes, the Address Latch Enable (ALE) pin indicates that the address bits, AD, are available on the external memory interface bus. Following the address latch, the Output Enable (OE) signal will enable both bytes of program memory at once to form a 16-bit instruction word. The Chip Enable (CE signal) is active at any time that the microcontroller accesses external memory, whether reading or writing; it is inactive (asserted high) whenever the device is in Sleep mode. In Byte Select mode, JEDEC® standard Flash memories will require BA0 for the byte address line and one I/O line to select between Byte and Word mode. The other 16-bit modes do not need BA0. JEDEC standard static RAM memories will use the UB or LB signals for byte selection. DS30000575C-page 159 PIC18F97J94 FAMILY 8.6.1 16-BIT BYTE WRITE MODE Figure 8-1 shows an example of 16-Bit Byte Write mode for PIC18FXXJ94 devices. This mode is used for two separate 8-bit memories connected for 16-bit operation. This generally includes basic EPROM and Flash devices. It allows table writes to byte-wide external memories. FIGURE 8-1: During a TBLWT instruction cycle, the TABLAT data is presented on the upper and lower bytes of the AD bus. The appropriate WRH or WRL control line is strobed on the LSb of the TBLPTR. 16-BIT BYTE WRITE MODE EXAMPLE D PIC18F97J94 AD (LSB) (MSB) 373 A D A A D D CE AD 373 OE D CE WR(2) OE WR(2) ALE A(1) CE OE WRH WRL Address Bus Data Bus Control Lines Note 1: 2: Upper order address lines are used only for 20-bit address widths. This signal only applies to table writes. See Section 7.1 “Table Reads and Table Writes”. DS30000575C-page 160  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 8.6.2 16-BIT WORD WRITE MODE Figure 8-2 shows an example of 16-Bit Word Write mode for PIC18FXXJ94 devices. This mode is used for word-wide memories, which includes some of the EPROM and Flash-type memories. This mode allows opcode fetches and table reads from all forms of 16-bit memory, and table writes to any type of word-wide external memories. This method makes a distinction between TBLWT cycles to even or odd addresses. During a TBLWT cycle to an even address (TBLPTR = 0), the TABLAT data is transferred to a holding latch and the external address data bus is tristated for the data portion of the bus cycle. No write signals are activated. FIGURE 8-2: During a TBLWT cycle to an odd address (TBLPTR = 1), the TABLAT data is presented on the upper byte of the AD bus. The contents of the holding latch are presented on the lower byte of the AD bus. The WRH signal is strobed for each write cycle; the WRL pin is unused. The signal on the BA0 pin indicates the LSb of the TBLPTR, but it is left unconnected. Instead, the UB and LB signals are active to select both bytes. The obvious limitation to this method is that the table write must be done in pairs on a specific word boundary to correctly write a word location. 16-BIT WORD WRITE MODE EXAMPLE PIC18F97J94 AD 373 A D AD A JEDEC® Word EPROM Memory D CE OE WR(2) 373 ALE A(1) CE OE WRH Address Bus Data Bus Control Lines Note 1: 2: Upper order address lines are used only for 20-bit address widths. This signal only applies to table writes. See Section 7.1 “Table Reads and Table Writes”.  2012-2016 Microchip Technology Inc. DS30000575C-page 161 PIC18F97J94 FAMILY 8.6.3 16-BIT BYTE SELECT MODE Figure 8-3 shows an example of 16-Bit Byte Select mode. This mode allows table write operations to wordwide external memories with byte selection capability. This generally includes both word-wide Flash and SRAM devices. During a TBLWT cycle, the TABLAT data is presented on the upper and lower byte of the AD bus. The WRH signal is strobed for each write cycle; the WRL pin is not used. The BA0 or UB/LB signals are used to select the byte to be written, based on the Least Significant bit of the TBLPTR register. FIGURE 8-3: Flash and SRAM devices use different control signal combinations to implement Byte Select mode. JEDEC standard Flash memories require that a controller I/O port pin be connected to the memory’s BYTE/WORD pin to provide the select signal. They also use the BA0 signal from the controller as a byte address. JEDEC standard static RAM memories, on the other hand, use the UB or LB signals to select the byte. 16-BIT BYTE SELECT MODE EXAMPLE PIC18F97J94 AD 373 A A JEDEC® Word FLASH Memory D D 138(3) AD 373 CE A0 BYTE/WORD ALE OE WR(1) A(2) OE WRH WRL A A BA0 JEDEC® Word SRAM Memory I/O D LB CE LB UB UB D OE WR(1) Address Bus Data Bus Control Lines Note 1: This signal only applies to table writes. See Section 7.1 “Table Reads and Table Writes”. 2: Upper order address lines are used only for 20-bit address width. 3: Demultiplexing is only required when multiple memory devices are accessed. DS30000575C-page 162  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 8.6.4 16-BIT MODE TIMING The presentation of control signals on the External Memory Bus is different for the various operating modes. Typical signal timing diagrams are shown in Figure 8-4 and Figure 8-5. FIGURE 8-4: EXTERNAL MEMORY BUS TIMING FOR TBLRD (EXTENDED MICROCONTROLLER MODE) Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 0Ch A 9256h CF33h AD CE ALE OE Memory Cycle Opcode Fetch TBLRD * from 000100h Opcode Fetch MOVLW 55h from 000102h TBLRD 92h from 199E67h Opcode Fetch ADDLW 55h from 000104h Instruction Execution INST(PC – 2) TBLRD Cycle 1 TBLRD Cycle 2 MOVLW FIGURE 8-5: EXTERNAL MEMORY BUS TIMING FOR SLEEP (EXTENDED MICROCONTROLLER MODE) Q1 Q2 Q4 Q1 Q2 3AAAh Q3 Q4 Q1 00h 00h A AD Q3 0003h 3AABh 0E55h CE ALE OE Memory Cycle Instruction Execution Opcode Fetch SLEEP from 007554h Opcode Fetch MOVLW 55h from 007556h INST(PC – 2) SLEEP  2012-2016 Microchip Technology Inc. Sleep Mode, Bus Inactive DS30000575C-page 163 PIC18F97J94 FAMILY 8.7 8-Bit Data Width Mode will enable one byte of program memory for a portion of the instruction cycle, then BA0 will change and the second byte will be enabled to form the 16-bit instruction word. The Least Significant bit of the address, BA0, must be connected to the memory devices in this mode. The Chip Enable (CE) signal is active at any time that the microcontroller accesses external memory, whether reading or writing. It is inactive (asserted high) whenever the device is in Sleep mode. In 8-Bit Data Width mode, the External Memory Bus operates only in Multiplexed mode; that is, data shares the 8 Least Significant bits of the address bus. Figure 8-6 shows an example of 8-Bit Multiplexed mode for 100-pin devices. This mode is used for a single, 8-bit memory, connected for 16-bit operation. The instructions will be fetched as two 8-bit bytes on a shared data/address bus. The two bytes are sequentially fetched within one instruction cycle (TCY). Therefore, the designer must choose external memory devices, according to timing calculations based on 1/ 2 TCY (2 times the instruction rate). For proper memory speed selection, glue logic propagation delay times must be considered, along with setup and hold times. This generally includes basic EPROM and Flash devices. It allows table writes to byte-wide external memories. During a TBLWT instruction cycle, the TABLAT data is presented on the upper and lower bytes of the AD bus. The appropriate level of the BA0 control line is strobed on the LSb of the TBLPTR. The Address Latch Enable (ALE) pin indicates that the address bits, AD, are available on the External Memory Bus interface. The Output Enable (OE) signal FIGURE 8-6: 8-BIT MULTIPLEXED MODE EXAMPLE D PIC18F97J94 AD ALE 373 A A A0 D D AD(1) A CE (1) OE WR(2) BA0 CE OE WRL Address Bus Data Bus Control Lines Note 1: 2: Upper order address bits are only used for 20-bit address width. The upper AD byte is used for all address widths except 8-bit. This signal only applies to table writes. See Section 7.1 “Table Reads and Table Writes”. DS30000575C-page 164  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 8.7.1 8-BIT MODE TIMING The presentation of control signals on the External Memory Bus is different for the various operating modes. Typical signal timing diagrams are shown in Figure 8-7 and Figure 8-8. FIGURE 8-7: EXTERNAL MEMORY BUS TIMING FOR TBLRD (EXTENDED MICROCONTROLLER MODE) Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 A 0Ch AD CFh 33h AD Q4 Q1 Q2 Q3 Q4 92h CE ALE OE Memory Cycle Instruction Execution FIGURE 8-8: Opcode Fetch TBLRD * from 000100h Opcode Fetch MOVLW 55h from 000102h TBLRD 92h from 199E67h Opcode Fetch ADDLW 55h from 000104h INST(PC – 2) TBLRD Cycle 1 TBLRD Cycle 2 MOVLW EXTERNAL MEMORY BUS TIMING FOR SLEEP (EXTENDED MICROCONTROLLER MODE) Q1 Q2 Q4 Q1 Q2 3Ah AD AAh 00h Q3 Q4 Q1 00h 00h A AD Q3 3Ah 03h ABh 0Eh 55h BA0 CE ALE OE Memory Cycle Instruction Execution Opcode Fetch SLEEP from 007554h Opcode Fetch MOVLW 55h from 007556h INST(PC – 2) SLEEP  2012-2016 Microchip Technology Inc. Sleep Mode, Bus Inactive DS30000575C-page 165 PIC18F97J94 FAMILY 8.8 Operation in Power-Managed Modes In Sleep and Idle modes, the microcontroller core does not need to access data; bus operations are suspended. The state of the external bus is frozen, with the address/data pins and most of the control pins holding at the same state they were in when the mode was invoked. The only potential changes are to the CE, LB and UB pins, which are held at logic high. In alternate, power-managed Run modes, the external bus continues to operate normally. If a clock source with a lower speed is selected, bus operations will run at that speed. In these cases, excessive access times for the external memory may result if Wait states have been enabled and added to external memory operations. If operations in a lower power Run mode are anticipated, users should provide in their applications for adjusting memory access times at the lower clock speeds. TABLE 8-3: REGISTERS ASSOCIATED WITH THE EXTERNAL MEMORY BUS Name Bit 7 Bit 6 Bit 5 Bit 4 MEMCON(1) EBDIS — WAIT1 WAIT0 — — WM1 WM0 RJPU RKPU RLPU LVDMD — EMBMD PADCFG PMD4 Bit 3 RDPU REPU RFPU RGPU RHPU CMP1MD CMP2MD CMP3MD USBMD IOCMD Bit 2 Bit 1 Bit 0 Legend: — = unimplemented, read as ‘0’. Shaded cells are not used during External Memory Bus access. Note 1: This register is unimplemented on 64-pin devices read as ‘0’. DS30000575C-page 166  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 9.0 8 x 8 HARDWARE MULTIPLIER 9.1 Introduction EXAMPLE 9-1: MOVF MULWF All PIC18 devices include an 8 x 8 hardware multiplier as part of the ALU. The multiplier performs an unsigned operation and yields a 16-bit result that is stored in the product register pair, PRODH:PRODL. The multiplier’s operation does not affect any flags in the STATUS register. ARG1, W ARG2 ; ; ARG1 * ARG2 -> ; PRODH:PRODL EXAMPLE 9-2: Making multiplication a hardware operation allows it to be completed in a single instruction cycle. This has the advantages of higher computational throughput and reduced code size for multiplication algorithms and allows PIC18 devices to be used in many applications previously reserved for digital-signal processors. A comparison of various hardware and software multiply operations, along with the savings in memory and execution time, is shown in Table 9-1. 9.2 8 x 8 UNSIGNED MULTIPLY ROUTINE 8 x 8 SIGNED MULTIPLY ROUTINE MOVF MULWF ARG1, W ARG2 BTFSC SUBWF ARG2, SB PRODH, F MOVF BTFSC SUBWF ARG2, W ARG1, SB PRODH, F ; ; ; ; ; ARG1 * ARG2 -> PRODH:PRODL Test Sign Bit PRODH = PRODH - ARG1 ; Test Sign Bit ; PRODH = PRODH ; - ARG2 Operation Example 9-1 shows the instruction sequence for an 8 x 8 unsigned multiplication. Only one instruction is required when one of the arguments is already loaded in the WREG register. Example 9-2 shows the sequence to do an 8 x 8 signed multiplication. To account for the sign bits of the arguments, each argument’s Most Significant bit (MSb) is tested and the appropriate subtractions are done. TABLE 9-1: Routine 8 x 8 Unsigned 8 x 8 Signed 16 x 16 Unsigned 16 x 16 Signed PERFORMANCE COMPARISON FOR VARIOUS MULTIPLY OPERATIONS Multiply Method Without Hardware Multiply Program Cycles Memory (Max) (Words) 13 Time @ 64 MHz @ 48 MHz @ 10 MHz @ 4 MHz 69 4.3 s 5.7 s 27.6 s 69 s Hardware Multiply 1 1 62.5 ns 83.3 ns 400 ns 1 s Without Hardware Multiply 33 91 5.6 s 7.5 s 36.4 s 91 s Hardware Multiply 6 6 375 ns 500 ns 2.4 s 6 s Without Hardware Multiply 21 242 15.1 s 20.1 s 96.8 s 242 s Hardware Multiply 28 28 1.7 s 2.3 s 11.2 s 28 s Without Hardware Multiply 52 254 15.8 s 21.2 s 101.6 s 254 s Hardware Multiply 35 40 2.5 s 3.3 s 16.0 s 40 s  2012-2016 Microchip Technology Inc. DS30000575C-page 167 PIC18F97J94 FAMILY Example 9-3 shows the sequence to do a 16 x 16 unsigned multiplication. Equation 9-1 shows the algorithm that is used. The 32-bit result is stored in four registers (RES3:RES0). EQUATION 9-1: RES3:RES0 = = 16 x 16 UNSIGNED MULTIPLICATION ALGORITHM ARG1H:ARG1L · ARG2H:ARG2L (ARG1H · ARG2H · 216) + (ARG1H · ARG2L · 28) + (ARG1L · ARG2H · 28) + (ARG1L · ARG2L) EXAMPLE 9-3: EQUATION 9-2: RES3:RES0= ARG1H:ARG1L · ARG2H:ARG2L = (ARG1H · ARG2H · 216) + (ARG1H · ARG2L · 28) + (ARG1L · ARG2H · 28) + (ARG1L · ARG2L) + (-1 · ARG2H · ARG1H:ARG1L · (-1 · ARG1H · ARG2H:ARG2L · EXAMPLE 9-4: MOVF MULWF 16 x 16 UNSIGNED MULTIPLY ROUTINE MOVF MULWF ARG1L, W ARG2L MOVFF MOVFF PRODH, RES1 PRODL, RES0 MOVF MULWF ARG1H, W ARG2H MOVFF MOVFF PRODH, RES3 PRODL, RES2 MOVF MULWF ARG1L, W ARG2H MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F MOVF MULWF ARG1H, W ARG2L MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F ; ARG1L * ARG2L-> ; PRODH:PRODL ; ; ARG1L * ARG2H-> PRODH:PRODL Add cross products ARG1H * ARG2L-> PRODH:PRODL Add cross products Example 9-4 shows the sequence to do a 16 x 16 signed multiply. Equation 9-2 shows the algorithm used. The 32-bit result is stored in four registers (RES3:RES0). To account for the sign bits of the arguments, the MSb for each argument pair is tested and the appropriate subtractions are done. DS30000575C-page 168 ARG1L, W ARG2L MOVFF MOVFF ; ARG1L * ARG2L -> ; PRODH:PRODL PRODH, RES1 ; PRODL, RES0 ; MOVF MULWF ARG1H, W ARG2H MOVFF MOVFF ; ARG1H * ARG2H -> ; PRODH:PRODL PRODH, RES3 ; PRODL, RES2 ; MOVF MULWF ARG1L, W ARG2H MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F MOVF MULWF ARG1H, W ARG2L MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F ; ; ; ; ; ; ; ; ARG1L * ARG2H -> PRODH:PRODL Add cross products ; ; ; ; ; ; ; ; ; ; ; 16 x 16 SIGNED MULTIPLY ROUTINE ; ; ; ; ; ; ; ; ; ; 216) + 216) ; ; ; ARG1H * ARG2H-> ; PRODH:PRODL ; ; 16 x 16 SIGNED MULTIPLICATION ALGORITHM ; ; ; ; ; ; ; ; ; ARG1H * ARG2L -> PRODH:PRODL Add cross products ; BTFSS ARG2H, 7 BRA SIGN_ARG1 MOVF ARG1L, W SUBWF RES2 MOVF ARG1H, W SUBWFB RES3 SIGN_ARG1 BTFSS ARG1H, 7 BRA CONT_CODE MOVF ARG2L, W SUBWF RES2 MOVF ARG2H, W SUBWFB RES3 ; CONT_CODE : ; ARG2H:ARG2L neg? ; no, check ARG1 ; ; ; ; ; ARG1H:ARG1L neg? ; no, done ; ; ;  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 10.0 INTERRUPTS Members of the PIC18F97J94 family of devices have multiple interrupt sources and an interrupt priority feature that allows most interrupt sources to be assigned a high-priority level or a low-priority level. The high-priority interrupt vector is at 0008h and the lowpriority interrupt vector is at 0018h. High-priority interrupt events will interrupt any low-priority interrupts that may be in progress. The registers for controlling interrupt operation are: • • • • • • • RCON INTCON INTCON2 INTCON3 PIR1, PIR2, PIR3, PIR4, PIR5 and PIR6 PIE1, PIE2, PIE3, PIE4, PIE5 and PIE6 IPR1, IPR2, IPR3, IPR5, IPR5 and IPR6 It is recommended that the Microchip header files, supplied with MPLAB® IDE, be used for the symbolic bit names in these registers. This allows the assembler/ compiler to automatically take care of the placement of these bits within the specified register. In general, interrupt sources have three bits to control their operation. They are: • Flag bit – Indicating that an interrupt event occurred • Enable bit – Enabling program execution to branch to the interrupt vector address when the flag bit is set • Priority bit – Specifying high priority or low priority 10.1 Mid-Range Compatibility When the IPEN bit is cleared (default state), the interrupt priority feature is disabled and interrupts are compatible with PIC® microcontroller mid-range devices. In Compatibility mode, the interrupt priority bits of the IPRx registers have no effect. The PEIE/ GIEL bit of the INTCON register is the global interrupt enable for the peripherals. The PEIE/GIEL bit disables only the peripheral interrupt sources and enables the peripheral interrupt sources when the GIE/GIEH bit is also set. The GIE/GIEH bit of the INTCON register is the global interrupt enable which enables all nonperipheral interrupt sources and disables all interrupt sources, including the peripherals. All interrupts branch to address 0008h in Compatibility mode.  2012-2016 Microchip Technology Inc. 10.2 Interrupt Priority The interrupt priority feature is enabled by setting the IPEN bit of the RCON register. When interrupt priority is enabled the GIE/GIEH and PEIE/GIEL global interrupt enable bits of Compatibility mode are replaced by the GIEH high priority, and GIEL low priority, global interrupt enables. When set, the GIEH bit of the INTCON register enables all interrupts that have their associated IPRx register or INTCONx register priority bit set (high priority). When clear, the GIEH bit disables all interrupt sources including those selected as low priority. When clear, the GIEL bit of the INTCON register disables only the interrupts that have their associated priority bit cleared (low priority). When set, the GIEL bit enables the low priority sources when the GIEH bit is also set. When the interrupt flag, enable bit and appropriate Global Interrupt Enable (GIE) bit are all set, the interrupt will vector immediately to address 0008h for high priority, or 0018h for low priority, depending on level of the interrupting source’s priority bit. Individual interrupts can be disabled through their corresponding interrupt enable bits. 10.3 Interrupt Response When an interrupt is responded to, the Global Interrupt Enable bit is cleared to disable further interrupts. The GIE/GIEH bit is the global interrupt enable when the IPEN bit is cleared. When the IPEN bit is set, enabling interrupt priority levels, the GIEH bit is the high priority global interrupt enable and the GIEL bit is the low priority global interrupt enable. High priority interrupt sources can interrupt a low priority interrupt. Low priority interrupts are not processed while high priority interrupts are in progress. The return address is pushed onto the stack and the PC is loaded with the interrupt vector address (0008h or 0018h). Once in the Interrupt Service Routine, the source(s) of the interrupt can be determined by polling the interrupt flag bits in the INTCONx and PIRx registers. The interrupt flag bits must be cleared by software before re-enabling interrupts to avoid repeating the same interrupt. The “return from interrupt” instruction, RETFIE, exits the interrupt routine and sets the GIE/GIEH bit (GIEH or GIEL if priority levels are used), which re-enables interrupts. DS30000575C-page 169 PIC18F97J94 FAMILY For external interrupt events, such as the INT pins or the PORTB interrupt-on-change, the interrupt latency will be three to four instruction cycles. The exact latency is the same for one-cycle or two-cycle instructions. Individual interrupt flag bits are set, regardless of the status of their corresponding enable bits or the Global Interrupt Enable bit. Note: Do not use the MOVFF instruction to modify any of the Interrupt Control registers while any interrupt is enabled. Doing so may cause erratic microcontroller behavior. FIGURE 10-1: PIC18F97J94 FAMILY INTERRUPT LOGIC PIR1 PIE1 IPR1 PIR2 PIE2 IPR2 PIR3 PIE3 IPR3 PIR4 PIE4 IPR4 PIR5 PIE5 IPR5 Wake-up if in Idle or Sleep modes TMR0IF TMR0IE TMR0IP RBIF RBIE RBIP INT0IF INT0IE INT1IF INT1IE INT1IP INT2IF INT2IE INT2IP INT3IF INT3IE INT3IP Interrupt to CPU Vector to Location 0008h GIE/GIEH IPEN PIR6 PIE6 IPR6 IPEN PEIE/GIEL IPEN High-Priority Interrupt Generation Low-Priority Interrupt Generation PIR1 PIE1 IPR1 PIR2 PIE2 IPR2 PIR3 PIE3 IPR3 PIR4 PIE4 IPR4 PIR5 PIE5 IPR5 PIR6 PIE6 IPR6 DS30000575C-page 170 TMR0IF TMR0IE TMR0IP RBIF RBIE RBIP INT1IF INT1IE INT1IP INT2IF INT2IE INT2IP INT3IF INT3IE INT3IP Interrupt to CPU Vector to Location 0018h IPEN GIE/GIEH PEIE/GIEL  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 10.4 INTCON Registers Note: The INTCON registers are readable and writable registers that contain various enable, priority and flag bits. REGISTER 10-1: Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the Global Interrupt Enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. INTCON: INTERRUPT CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R-0 GIE/GIEH PEIE/GIEL TMR0IE INT0IE IOCIE TMR0IF INT0IF IOCIF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 GIE/GIEH: Global Interrupt Enable bit When IPEN = 0: 1 = Enables all unmasked interrupts 0 = Disables all interrupts including peripherals When IPEN = 1: 1 = Enables all high-priority interrupts 0 = Disables all interrupts including low priority bit 6 PEIE/GIEL: Peripheral Interrupt Enable bit When IPEN = 0: 1 = Enables all unmasked peripheral interrupts 0 = Disables all peripheral interrupts When IPEN = 1: 1 = Enables all low-priority peripheral interrupts 0 = Disables all low-priority peripheral interrupts bit 5 TMR0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 overflow interrupt 0 = Disables the TMR0 overflow interrupt bit 4 INT0IE: INT0 External Interrupt Enable bit 1 = Enables the INT0 external interrupt 0 = Disables the INT0 external interrupt bit 3 IOCIE: I/O Change Interrupt Enable bit 1 = Enables the I/O port change interrupt 0 = Disables the I/O port change interrupt bit 2 TMR0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register has not overflowed bit 1 INT0IF: INT0 External Interrupt Flag bit 1 = The INT0 external interrupt occurred (must be cleared in software) 0 = The INT0 external interrupt did not occur bit 0 IOCIF: I/O Port Change Interrupt Flag bit 1 = At least one of the IOC pins changed state (must be cleared by clearing all the IOCF bits in the IOC module) 0 = None of the IOC pins have changed state  2012-2016 Microchip Technology Inc. DS30000575C-page 171 PIC18F97J94 FAMILY REGISTER 10-2: INTCON2: INTERRUPT CONTROL REGISTER 2 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 RBPU INTEDG0 INTEDG1 INTEDG2 INTEDG3 TMR0IP INT3IP IOCIP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 RBPU: PORTB Pull-up Enable bit 1 = All PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual port latch values bit 6 INTEDG0: External Interrupt 0 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 5 INTEDG1: External Interrupt 1 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 4 INTEDG2: External Interrupt 2 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 3 INTEDG3: External Interrupt 3 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 2 TMR0IP: TMR0 Overflow Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 INT3IP: INT3 External Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 IOCIP: RB Port Change Interrupt Priority bit 1 = High priority 0 = Low priority Note: x = Bit is unknown Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the Global Interrupt Enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. DS30000575C-page 172  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 10-3: INTCON3: INTERRUPT CONTROL REGISTER 3 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INT2IP INT1IP INT3IE INT2IE INT1IE INT3IF INT2IF INT1IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 INT2IP: INT2 External Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 INT1IP: INT1 External Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 INT3IE: INT3 External Interrupt Enable bit 1 = Enables the INT3 external interrupt 0 = Disables the INT3 external interrupt bit 4 INT2IE: INT2 External Interrupt Enable bit 1 = Enables the INT2 external interrupt 0 = Disables the INT2 external interrupt bit 3 INT1IE: INT1 External Interrupt Enable bit 1 = Enables the INT1 external interrupt 0 = Disables the INT1 external interrupt bit 2 INT3IF: INT3 External Interrupt Flag bit 1 = The INT3 external interrupt occurred (must be cleared in software) 0 = The INT3 external interrupt did not occur bit 1 INT2IF: INT2 External Interrupt Flag bit 1 = The INT2 external interrupt occurred (must be cleared in software) 0 = The INT2 external interrupt did not occur bit 0 INT1IF: INT1 External Interrupt Flag bit 1 = The INT1 external interrupt occurred (must be cleared in software) 0 = The INT1 external interrupt did not occur Note: x = Bit is unknown Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the Global Interrupt Enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling.  2012-2016 Microchip Technology Inc. DS30000575C-page 173 PIC18F97J94 FAMILY 10.5 PIR Registers The PIR registers contain the individual flag bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are six Peripheral Interrupt Request (Flag) registers (PIR1 through PIR5). Note 1: Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the Global Interrupt Enable bit, GIE (INTCON). 2: User software should ensure the appropriate interrupt flag bits are cleared prior to enabling an interrupt and after servicing that interrupt. REGISTER 10-4: PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1 R/W-0 R/W-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0 PSPIF ADIF RC1IF TX1IF SSP1IF TMR1GIF TMR2IF TMR1IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 PSPIF: Parallel Slave Port Read/Write Interrupt Flag bit 1 = A read or write operation has taken place (must be cleared in software) 0 = No read or write operation has occurred bit 6 ADIF: A/D Converter Interrupt Flag bit 1 = An A/D conversion completed (must be cleared in software) 0 = The A/D conversion is not complete bit 5 RC1IF: EUSART1 Receive Interrupt Flag bit 1 = The EUSART1 receive buffer, RCREG1, is full (cleared when RCREG1 is read) 0 = The EUSART1 receive buffer is empty bit 4 TX1IF: EUSART1 Transmit Interrupt Flag bit 1 = The EUSART1 transmit buffer, TXREG1, is empty (cleared when TXREG1 is written) 0 = The EUSART1 transmit buffer is full bit 3 SSP1IF: Master Synchronous Serial Port 1 Interrupt Flag bit 1 = The transmission/reception is complete (must be cleared in software) 0 = Waiting to transmit/receive bit 2 TMR1GIF: Timer1 Gate Interrupt Flag bit 1 = Timer gate interrupt occurred (must be cleared in software) 0 = No timer gate interrupt occurred bit 1 TMR2IF: TMR2 to PR2 Match Interrupt Flag bit 1 = TMR2 to PR2 match occurred (must be cleared in software) 0 = No TMR2 to PR2 match occurred bit 0 TMR1IF: TMR1 Overflow Interrupt Flag bit 1 = TMR1 register overflowed (must be cleared in software) 0 = TMR1 register did not overflow DS30000575C-page 174  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 10-5: PIR2: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OSCFIF SSP2IF BCL2IF USBIF BCL1IF HLVDIF TMR3IF TMR3GIF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 OSCFIF: Oscillator Fail Interrupt Flag bit 1 = Device oscillator failed, clock input has changed to INTOSC (bit must be cleared in software) 0 = Device clock operating bit 6 SSP2IF: Master Synchronous Serial Port 2 Interrupt Flag bit 1 = The transmission/reception is complete (must be cleared in software) 0 = Waiting to transmit/receive bit 5 BCL2IF: Bus Collision Interrupt Flag bit 1 = A bus collision has occurred while the MSSP1 module configured in I2C master was transmitting (must be cleared in software) 0 = No bus collision occurred bit 4 USBIF: Oscillator Fail Interrupt Flag bit 1 = USB requested an interrupt (must be cleared in software) 0 = No USB interrupt request bit 3 BCL1IF: Bus Collision Interrupt Flag bit 1 = A bus collision occurred (bit must be cleared in software) 0 = No bus collision occurred bit 2 HLVDIF: High/Low-Voltage Detect Interrupt Flag bit 1 = A low-voltage condition occurred (bit must be cleared in software) 0 = The device voltage is above the regulator’s low-voltage trip point bit 1 TMR3IF: TMR3 Overflow Interrupt Flag bit 1 = TMR3 register overflowed (bit must be cleared in software) 0 = TMR3 register did not overflow bit 0 TMR3GIF: TMR3 Gate Interrupt Flag bit 1 = Timer gate interrupt occurred (bit must be cleared in software) 0 = No timer gate interrupt occurred  2012-2016 Microchip Technology Inc. DS30000575C-page 175 PIC18F97J94 FAMILY REGISTER 10-6: PIR3: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 3 R/W-0 R/W-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0 TMR5GIF LCDIF RC2IF TX2IF CTMUIF CCP2IF CCP1IF RTCCIF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 TMR5GIF: TMR5 Gate Interrupt Flag bits 1 = TMR gate interrupt occurred (must be cleared in software) 0 = No TMR gate occurred bit 6 LCDIF: LCD Interrupt Flag bit 1 = A write is allowed to the Segment Data Registers 0 = A write is not allowed to the Segment Data Register bit 5 RC2IF: EUSART2 Receive Interrupt Flag bit 1 = The EUSART2 receive buffer, RCREG2, is full (cleared when RCREG2 is read) 0 = The EUSART2 receive buffer is empty bit 4 TX2IF: EUSART2 Transmit Interrupt Flag bit 1 = The EUSART2 transmit buffer, TXREG2, is empty (cleared when TXREG2 is written) 0 = The EUSART2 transmit buffer is full bit 3 CTMUIF: CTMU Interrupt Flag bit 1 = CTMU interrupt occurred (must be cleared in software) 0 = No CTMU interrupt occurred bit 2 CCP2IF: CCP2 Interrupt Flag bit Capture mode: 1 = A TMR1/TMR3 register capture occurred (must be cleared in software) 0 = No TMR1/TMR3 register capture occurred Compare mode: 1 = A TMR1/TMR3 register compare match occurred (must be cleared in software) 0 = No TMR1/TMR3 register compare match occurred PWM mode: Unused in this mode. bit 1 CCP1IF: ECCP1 Interrupt Flag bit Capture mode: 1 = A TMR1/TMR3 register capture occurred (must be cleared in software) 0 = No TMR1/TMR3 register capture occurred Compare mode: 1 = A TMR1/TMR3 register compare match occurred (must be cleared in software) 0 = No TMR1/TMR3 register compare match occurred PWM mode: Unused in this mode. bit 0 RTCCIF: RTCC Interrupt Flag bit 1 = RTCC interrupt occurred (must be cleared in software) 0 = No RTCC interrupt occurred DS30000575C-page 176  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 10-7: PIR4: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 4 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CCP10IF CCP9IF CCP8IF CCP7IF CCP6IF CCP5IF CCP4IF ECCP3IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 CCP10IF: CCP10 Interrupt Flag bits Capture mode: 1 = A TMR register capture occurred (bit must be cleared in software) 0 = No TMR register capture occurred Compare mode: 1 = A TMR register compare match occurred (must be cleared in software) 0 = No TMR register compare match occurred PWM mode: Not used in PWM mode. bit 6 CCP9IF: CCP9 Interrupt Flag bits Capture mode: 1 = A TMR register capture occurred (bit must be cleared in software) 0 = No TMR register capture occurred Compare mode: 1 = A TMR register compare match occurred (must be cleared in software) 0 = No TMR register compare match occurred PWM mode: Not used in PWM mode. bit 5 CCP8IF: CCP8 Interrupt Flag bits Capture mode: 1 = A TMR register capture occurred (bit must be cleared in software) 0 = No TMR register capture occurred Compare mode: 1 = A TMR register compare match occurred (must be cleared in software) 0 = No TMR register compare match occurred PWM mode: Not used in PWM mode. bit 4 CCP7IF: CCP7 Interrupt Flag bit 1 = Interrupt Flag bits Capture mode: 1 = A TMR register capture occurred (bit must be cleared in software) 0 = No TMR register capture occurred Compare mode: 1 = A TMR register compare match occurred (must be cleared in software) 0 = No TMR register compare match occurred PWM mode: Not used in PWM mode.  2012-2016 Microchip Technology Inc. DS30000575C-page 177 PIC18F97J94 FAMILY REGISTER 10-7: PIR4: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 4 (CONTINUED) bit 3 CCP6IF: CCP6 Interrupt Flag bits Capture mode: 1 = A TMR register capture occurred (bit must be cleared in software) 0 = No TMR register capture occurred Compare mode: 1 = A TMR register compare match occurred (must be cleared in software) 0 = No TMR register compare match occurred PWM mode: Not used in PWM mode. bit 2 CCP5IF: CCP5 Interrupt Flag bits Capture mode: 1 = A TMR register capture occurred (bit must be cleared in software) 0 = No TMR register capture occurred Compare mode: 1 = A TMR register compare match occurred (must be cleared in software) 0 = No TMR register compare match occurred PWM mode: Not used in PWM mode. bit 1 CCP4IF: CCP4 Interrupt Flag bits Capture mode: 1 = A TMR register capture occurred (bit must be cleared in software) 0 = No TMR register capture occurred Compare mode: 1 = A TMR register compare match occurred (must be cleared in software) 0 = No TMR register compare match occurred PWM mode: Not used in PWM mode. bit 0 ECCP3IF: ECCP3 Interrupt Flag bits Capture mode: 1 = A TMR register capture occurred (bit must be cleared in software) 0 = No TMR register capture occurred Compare mode: 1 = A TMR register compare match occurred (must be cleared in software) 0 = No TMR register compare match occurred PWM mode: Not used in PWM mode. DS30000575C-page 178  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 10-8: PIR5: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 5 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 — ACTORSIF ACTLOCKIF TMR8IF — TMR6IF TMR5IF TMR4IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 Unimplemented: Read as ‘0’ bit 6 ACTORSIF: Active Clock Tuning Out-of-Range Interrupt Flag bit 1 = Active clock tuning out-of-range occurred 0 = Active tuning out-of-range did not occur bit 5 ACTLOCKIF: Active Clock Tuning Lock Interrupt Flag bit 1 = Active clock tuning lock/unlock occurred 0 = Active clock tuning lock/unlock did not occur bit 4 TMR8IF: TMR8 to PR8 Match Interrupt Flag bit 1 = TMR8 to PR8 match occurred (must be cleared in software) 0 = No TMR8 to PR8 match occurred bit 3 Unimplemented: Read as ‘0’ bit 2 TMR6IF: TMR6 to PR6 Match Interrupt Flag bit 1 = TMR6 to PR6 match occurred (must be cleared in software) 0 = No TMR6 to PR6 match occurred bit 1 TMR5IF: TMR5 Overflow Interrupt Flag bit 1 = TMR5 register overflowed (must be cleared in software) 0 = TMR5 register did not overflow bit 0 TMR4IF: TMR4 to PR4 Match Interrupt Flag bit 1 = TMR4 to PR4 match occurred (must be cleared in software) 0 = No TMR4 to PR4 match occurred  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 179 PIC18F97J94 FAMILY REGISTER 10-9: PIR6: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 6 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 RC4IF TX4IF RC3IF TX3IF — CMP3IF CMP2IF CMP1IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 RC4IF: EUSART4 Receive Interrupt Flag bit 1 = The EUSART4 receive buffer is full (cleared by reading RCREG4) 0 = The EUSART4 receive buffer is empty bit 6 TX4IF: EUSART4 Transmit Interrupt Flag bit 1 = The EUSART4 transmit buffer is empty (cleared by writing to TXREG4) 0 = The EUSART4 transmit buffer is full bit 5 RC3IF: EUSART3 Receive Interrupt Flag bit 1 = The EUSART3 receive buffer is full (cleared by reading RCREG3) 0 = The EUSART3 receive buffer is empty bit 4 TX3IF: EUSART3 Transmit Interrupt Flag bit 1 = The EUSART3 transmit buffer is empty (cleared by writing to TXREG3) 0 = The EUSART3 transmit buffer is full bit 3 Unimplemented: Read as ‘0’ bit 2 CMP3IF: CMP3 Interrupt Flag bit 1 = CMP3 interrupt occurred (must be cleared in software) 0 = No CMP3 interrupt occurred bit 1 CMP2IF: CMP2 Interrupt Flag bit 1 = CMP2 interrupt occurred (must be cleared in software) 0 = No CMP2 interrupt occurred bit 0 CMP1IF: CM1 Interrupt Flag bit 1 = CMP1 interrupt occurred (must be cleared in software) 0 = No CMP1 interrupt occurred DS30000575C-page 180  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 10.6 PIE Registers The PIE registers contain the individual enable bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are six Peripheral Interrupt Enable registers (PIE1 through PIE6). When IPEN (RCON) = 0, the PEIE bit must be set to enable any of these peripheral interrupts. REGISTER 10-10: PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSPIE ADIE RC1IE TX1IE SSP1IE TMR1GIE TMR2IE TMR1IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 PSPIE: Parallel Slave Port Read/Write Interrupt Enable bit 1 = Enables the PSP read/write interrupt 0 = Disables the PSP read/write interrupt bit 6 ADIE: A/D Converter Interrupt Enable bit 1 = Enables the A/D interrupt 0 = Disables the A/D interrupt bit 5 RC1IE: EUSART1 Receive Interrupt Enable bit 1 = Enables the EUSART1 receive interrupt 0 = Disables the EUSART1 receive interrupt bit 4 TX1IE: EUSART1 Transmit Interrupt Enable bit 1 = Enables the EUSART1 transmit interrupt 0 = Disables the EUSART1 transmit interrupt bit 3 SSP1IE: Master Synchronous Serial Port 1 Interrupt Enable bit 1 = Enables the MSSP1 interrupt 0 = Disables the MSSP1 interrupt bit 2 TMR1GIE: TMR1 Gate Interrupt Enable bit 1 = Enables the gate 0 = Disables the gate bit 1 TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the TMR2 to PR2 match interrupt 0 = Disables the TMR2 to PR2 match interrupt bit 0 TMR1IE: TMR1 Overflow Interrupt Enable bit 1 = Enables the TMR1 overflow interrupt 0 = Disables the TMR1 overflow interrupt  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 181 PIC18F97J94 FAMILY REGISTER 10-11: PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OSCFIE SSP2IE BCL2IE USBIE BCL1IE HLVDIE TMR3IE TMR3GIE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 OSCFIE: Oscillator Fail Interrupt Enable bit 1 = Enabled 0 = Disabled bit 6 SSP2IE: Master Synchronous Serial Port 2 Interrupt Enable bit 1 = Enables the MSSP2 interrupt 0 = Disables the MSSP2 interrupt bit 5 BCL2IE: Bus Collision Interrupt Enable bit (MSSP) 1 = Enabled 0 = Disabled bit 4 USBIE: USB Interrupt Enable bit 1 = Enabled 0 = Disabled bit 3 BCLIE: Bus Collision Interrupt Enable bit 1 = Enabled 0 = Disabled bit 2 HLVDIE: High/Low-Voltage Detect Interrupt Enable bit 1 = Enabled 0 = Disabled bit 1 TMR3IE: TMR3 Overflow Interrupt Enable bit 1 = Enabled 0 = Disabled bit 0 TMR3GIE: Timer3 Gate Interrupt Enable bit 1 = Enabled 0 = Disabled DS30000575C-page 182 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 10-12: PIE3: PERIPHERAL INTERRUPT ENABLE REGISTER 3 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TMR5GIE LCDIE RC2IE TX2IE CTMUIE CCP2IE CCP1IE RTCCIE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 TMR5GIE: TMR5 Gate Interrupt Enable bit 1 = Enabled 0 = Disabled bit 6 LCDIE: LCD Ready Interrupt Enable bit 1 = Enabled 0 = Disabled bit 5 RC2IE: EUSART2 Receive Interrupt Enable bit 1 = Enabled 0 = Disabled bit 4 TX2IE: EUSART2 Transmit Interrupt Enable bit 1 = Enabled 0 = Disabled bit 3 CTMUIE: CTMU Interrupt Enable bit 1 = Enabled 0 = Disabled bit 2 CCP2IE: CCP2 Interrupt Enable bit 1 = Enabled 0 = Disabled bit 1 CCP1IE: ECCP1 Interrupt Enable bit 1 = Enabled 0 = Disabled bit 0 RTCCIE: RTCC Interrupt Enable bit 1 = Enabled 0 = Disabled  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 183 PIC18F97J94 FAMILY REGISTER 10-13: PIE4: PERIPHERAL INTERRUPT ENABLE REGISTER 4 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CCP10IE CCP9IE CCP8IE CCP7IE CCP6IE CCP5IE CCP4IE ECCP3IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 CCP10IE: CCP10 Interrupt Enable bit 1 = Enabled 0 = Disabled bit 6 CCP9IE: CCP9 Interrupt Enable bit 1 = Enabled 0 = Disabled bit 5 CCP8IE: CCP8 Interrupt Enable bit 1 = Enabled 0 = Disabled bit 4 CCP7IE: CCP7 Interrupt Enable bit 1 = Enabled 0 = Disabled bit 3 CCP6IE: CCP6 Interrupt Enable bit 1 = Enabled 0 = Disabled bit 2 CCP5IE: CCP5 Interrupt Flag bit 1 = Enabled 0 = Disabled bit 1 CCP4IE: CCP4 Interrupt Flag bit 1 = Enabled 0 = Disabled bit 0 ECCP3IE: ECCP3 Interrupt Flag bit 1 = Enabled 0 = Disabled DS30000575C-page 184 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 10-14: PIE5: PERIPHERAL INTERRUPT ENABLE REGISTER 5 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 — ACTORSIE ACTLOCKIE TMR8IE — TMR6IE TMR5IE TMR4IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 Unimplemented: Read as ‘0’ bit 6 ACTORSIE: Active Clock Tuning Out-of-Range Interrupt Enable bit 1 = Enables the active clock tuning out-of-range interrupt 0 = Disables the active clock tuning out-of-range interrupt bit 5 ACTLOCKIE: Active Clock Tuning Lock Interrupt Enable bit 1 = Enables the active clock tuning lock/unlock interrupt 0 = Disables the active clock tuning lock/unlock interrupt bit 4 TMR8IE: TMR8 to PR8 Match Interrupt Enable bit 1 = Enables the TMR8 to PR8 match interrupt 0 = Disables the TMR8 to PR8 match interrupt bit 3 Unimplemented: Read as ‘0’ bit 2 TMR6IE: TMR6 to PR6 Match Interrupt Enable bit 1 = Enables the TMR6 to PR6 match interrupt 0 = Disables the TMR6 to PR6 match interrupt bit 1 TMR5IE: TMR5 Overflow Interrupt Enable bit 1 = Enables the TMR5 overflow interrupt 0 = Disables the TMR5 overflow interrupt bit 0 TMR4IE: TMR4 to PR4 Match Interrupt Enable bit 1 = Enables the TMR4 to PR4 match interrupt 0 = Disables the TMR4 to PR4 match interrupt  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 185 PIC18F97J94 FAMILY REGISTER 10-15: PIE6: PERIPHERAL INTERRUPT ENABLE REGISTER 6 R/W-0 R/W-0 RC4IE TX4IE R/W-0 RC3IE R/W-0 U-0 R/W-0 R/W-0 R/W-0 TX3IE — CMP3IE CMP2IE CMP1IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 RC4IE: EUSART4 Receive Interrupt Enable bit 1 = Enabled 0 = Disabled bit 6 TX4IE: EUSART4 Transmit Interrupt Enable bit 1 = Enabled 0 = Disabled bit 5 RC34IE: EUSART3 Receive Interrupt Enable bit 1 = Enabled 0 = Disabled bit 4 TX3IE: EUSART3 Transmit Interrupt Enable bit 1 = Enabled 0 = Disabled bit 3 Unimplemented: Read as ‘0’ bit 2 CMP3IE: Comparator 3 Interrupt Enable bit 1 = Enabled 0 = Disabled bit 1 CMP2IE: Comparator 2 Interrupt Enable bit 1 = Enabled 0 = Disabled bit 0 CMP1IE: Comparator 1 Interrupt Enable bit 1 = Enabled 0 = Disabled DS30000575C-page 186 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 10.7 IPR Registers The IPR registers contain the individual priority bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are six Peripheral Interrupt Priority registers (IPR1 through IPR6). Using the priority bits requires that the Interrupt Priority Enable (IPEN) bit (RCON) be set. REGISTER 10-16: IPR1: PERIPHERAL INTERRUPT PRIORITY REGISTER 1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 PSPIP ADIP RC1IP TX1IP SSP1IP TMR1GIP TMR2IP TMR1IP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 PSPIP: Parallel Slave Port Read/Write Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 ADIP: A/D Converter Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 RC1IP: EUSART1 Receive Interrupt Priority bit 1 = High priority 0 = Low priority bit 4 TX1IP: EUSART1 Transmit Interrupt Priority bit x = Bit is unknown 1 = High priority 0 = Low priority bit 3 SSP1IP: Master Synchronous Serial Port 1 Interrupt Priority bit 1 = High priority 0 = Low priority bit 2 TMR1GIP: Timer1 Gate Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 TMR2IP: TMR2 to PR2 Match Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 TMR1IP: TMR1 Overflow Interrupt Priority bit 1 = High priority 0 = Low priority  2012-2016 Microchip Technology Inc. DS30000575C-page 187 PIC18F97J94 FAMILY REGISTER 10-17: IPR2: PERIPHERAL INTERRUPT PRIORITY REGISTER 2 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 OSCFIP SSP2IP BCL2IP USBIP BCL1IP HLVDIP TMR3IP TMR3GIP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 OSCFIP: Oscillator Fail Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 SSP2IP: Master Synchronous Serial Port 2 Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 BCL2IP: Bus Collision Interrupt Priority bit (MSSP) 1 = High priority 0 = Low priority bit 4 USBIP: USB Interrupt Priority bit 1 = High priority 0 = Low priority bit 3 BCL1IP: Bus Collision Interrupt Priority bit 1 = High priority 0 = Low priority bit 2 HLVDIP: High/Low-Voltage Detect Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 TMR3IP: TMR3 Overflow Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 TMR3GIP: TMR3 Gate Interrupt Priority bit 1 = High priority 0 = Low priority DS30000575C-page 188 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 10-18: IPR3: PERIPHERAL INTERRUPT PRIORITY REGISTER 3 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 TMR5GIP LCDIP RC2IP TX2IP CTMUIP CCP2IP CCP1IP RTCCIP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 TMR5GIP: TMR5 Gate Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 LCDIP: LCD Ready Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 RC2IP: EUSART2 Receive Priority Flag bit 1 = High priority 0 = Low priority bit 4 TX2IP: EUSART2 Transmit Interrupt Priority bit 1 = High priority 0 = Low priority bit 3 CTMUIP: CTMU Interrupt Priority bit 1 = High priority 0 = Low priority bit 2 CCP2IP: CCP2 Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 CCP1IP: ECCP1 Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 RTCCIP: RTCC Interrupt Priority bit 1 = High priority 0 = Low priority  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 189 PIC18F97J94 FAMILY REGISTER 10-19: IPR4: PERIPHERAL INTERRUPT PRIORITY REGISTER 4 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 CCP10IP CCP9IP CCP8IP CCP7IP CCP6IP CCP5IP CCP4IP ECCP3IP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 CCP10IP: CCP10 Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 CCP9IP: CCP9 Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 CCP8IP: CCP8 Interrupt Priority bit 1 = High priority 0 = Low priority bit 4 CCP7IP: CCP7 Interrupt Priority bit 1 = High priority 0 = Low priority bit 3 CCP6IP: CCP6 Interrupt Priority bit 1 = High priority 0 = Low priority bit 2 CCP5IP: CCP5 Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 CCP4IP: CCP4 Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 ECCP3IP: ECCP3 Interrupt Priority bits 1 = High priority 0 = Low priority DS30000575C-page 190 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 10-20: IPR5: PERIPHERAL INTERRUPT PRIORITY REGISTER 5 U-0 R/W-1 R/W-1 R/W-1 U-0 R/W-1 R/W-1 R/W-1 — ACTORSIP ACTLOCKIP TMR8IP — TMR6IP TMR5IP TMR4IP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 Unimplemented: Read as ‘0’ bit 6 ACTORSIP: Active Clock Tuning Out-of-Range Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 ACTLOCKIP: Active Clock Tuning Lock Interrupt Priority bit 1 = High priority 0 = Low priority bit 4 TMR8IP: TMR8 to PR8 Match Interrupt Priority bit 1 = High priority 0 = Low priority bit 3 Unimplemented: Read as ‘0’ bit 2 TMR6IP: TMR6 to PR6 Match Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 TMR5IP: TMR5 Overflow Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 TMR4IP: TMR4 to PR4 Match Interrupt Priority bit 1 = High priority 0 = Low priority  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 191 PIC18F97J94 FAMILY REGISTER 10-21: IPR6: PERIPHERAL INTERRUPT PRIORITY REGISTER 6 R/W-1 R/W-1 RC4IP TX4IP R/W-1 RC3IP R/W-1 U-O R/W-1 R/W-1 R/W-1 TX3IP — CMP3IP CMP2IP CMP1IP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 RCP4IP: EUSART4 Receive Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 TX4IP: EUSART4 Transmit Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 RC3IP: EUSART3 Receive Interrupt Priority bit 1 = High priority 0 = Low priority bit 4 TX3IP: EUSART3 Transmit Interrupt Priority bit 1 = High priority 0 = Low priority bit 3 Unimplemented: Read as ‘0’ bit 2 CMP3IP: CMP3 Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 CMP2IP: CMP2 Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 CMP1IP: CMP1 Interrupt Priority bit 1 = High priority 0 = Low priority DS30000575C-page 192 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 10.8 RCON Register The RCON register contains bits used to determine the cause of the last Reset or wake-up from Idle or Sleep modes. RCON also contains the bit that enables interrupt priorities (IPEN). REGISTER 10-22: RCON: RESET CONTROL REGISTER R/W-0 U-0 R/W-1 R/W-1 R-1 R-1 R/W-0 R/W-0 IPEN — CM RI TO PD POR BOR bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 IPEN: Interrupt Priority Enable bit 1 = Enables priority levels on interrupts 0 = Disables priority levels on interrupts (PIC16CXXX Compatibility mode) bit 6 Unimplemented: Read as ‘0’ bit 5 CM: Configuration Mismatch Flag bit 1 = A Configuration Mismatch Reset has not occurred 0 = A Configuration Mismatch Reset has occurred (must be subsequently set in software) bit 4 RI: RESET Instruction Flag bit For details of bit operation, see Register 5-1. bit 3 TO: Watchdog Timer Time-out Flag bit For details of bit operation, see Register 5-1. bit 2 PD: Power-Down Detection Flag bit For details of bit operation, see Register 5-1. bit 1 POR: Power-on Reset Status bit For details of bit operation, see Register 5-1. bit 0 BOR: Brown-out Reset Status bit For details of bit operation, see Register 5-1.  2012-2016 Microchip Technology Inc. DS30000575C-page 193 PIC18F97J94 FAMILY 10.9 INTx Pin Interrupts External interrupts on INT0, INT1, INT2 and INT3 are edge-triggered. INT0 is multiplexed with RB0 pin whereas INT1, INT2 and INT3 can only be used via remappable pins as shown in Table 11-13. If the corresponding INTEDGx bit in the INTCON2 register is set (= 1), the interrupt is triggered by a rising edge. If that bit is clear, the trigger is on the falling edge. When a valid edge appears on the RBx/INTx pin, the corresponding flag bit, INTxIF, is set. This interrupt can be disabled by clearing the corresponding enable bit, INTxIE. Before re-enabling the interrupt, the flag bit (INTxIF) must be cleared in software in the Interrupt Service Routine. All external interrupts (INT0, INT1, INT2 and INT3) can wake-up the processor from the power-managed modes if bit, INTxIE, was set prior to going into the power-managed modes. If the Global Interrupt Enable bit (GIE) is set, the processor will branch to the interrupt vector following wake-up. The interrupt priority for INT1, INT2 and INT3 is determined by the value contained in the Interrupt Priority bits, INT1IP (INTCON3), INT2IP (INTCON3) and INT3IP (INTCON2). There is no priority bit associated with INT0. It is always a high-priority interrupt source. The interrupt can be enabled/disabled by setting/clearing enable bit, TMR0IE (INTCON). Interrupt priority for Timer0 is determined by the value contained in the interrupt priority bit, TMR0IP (INTCON2). For further details on the Timer0 module, see Section 14.0 “Timer0 Module”. 10.11 Edge-Selectable Interrupt-onChange Interrupt-on-change pins are selected via the PPS register settings and have the option of generating an interrupt on positive or negative transitions, or both. Positive edge events are enabled by setting the corresponding bits in the IOCP register, while negative edge events are enabled by setting the corresponding bits in the IOCN register. For compatibility with the previous interrupt-on-change feature, both the IOCP and IOCN bits should be set. The interrupt can be enabled by setting/clearing the IOCIE (INTCON) bit. Each individual pin can be disabled by clearing both of the corresponding IOCN/IOCP bits. A change event (either positive or negative edge) will cause the corresponding IOCF flag to be set. Interrupt priority for the edge selectable interrupt-onchange is determined by the interrupt priority bit, IOCIP (INTCON2). 10.10 TMR0 Interrupt In 8-bit mode (the default), an overflow in the TMR0 register (FFh  00h) will set flag bit, TMR0IF. In 16-bit mode, an overflow in the TMR0H:TMR0L register pair (FFFFh  0000h) will set TMR0IF. DS30000575C-page 194  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 10-23: IOCP: INTERRUPT-ON-CHANGE POSITIVE EDGE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IOCP7 IOCP6 IOCP5 IOCP4 IOCP3 IOCP2 IOCP1 IOCP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 x = Bit is unknown IOCP: Interrupt-on-Change Positive Edge Enable bits 1 = Interrupt-on-change is enabled on the pin for a rising edge; associated Status bit and interrupt flag will be set upon detecting an edge 0 = Interrupt-on-change is disabled for the associated pin REGISTER 10-24: IOCN: INTERRUPT-ON-CHANGE NEGATIVE EDGE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IOCN7 IOCN6 IOCN5 IOCN4 IOCN3 IOCN2 IOCN1 IOCN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 x = Bit is unknown IOCN: Interrupt-on-Change Negative Edge Enable bits 1 = Interrupt-on-change is enabled on the pin for a falling edge; associated Status bit and interrupt flag will be set upon detecting an edge 0 = Interrupt-on-change is disabled for the associated pin REGISTER 10-25: IOCF: INTERRUPT-ON-CHANGE FLAG REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IOCF7 IOCF6 IOCF5 IOCF4 IOCF3 IOCF2 IOCF1 IOCF0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 x = Bit is unknown IOCF: Interrupt-on-Change Flag bits 1 = An enabled change was detected on the associated pin; this is set when IOCP = 1 and a positive edge was detected on the input pin or when IOCN = 1 and a negative edge was detected on the input pin (clear in software to clear the IOCIF bit) 0 = No change was detected or the user cleared the detected change  2012-2016 Microchip Technology Inc. DS30000575C-page 195 PIC18F97J94 FAMILY 10.12 Context Saving During Interrupts During interrupts, the return PC address is saved on the stack. Additionally, the WREG, STATUS and BSR registers are saved on the Fast Return Stack. If a fast return from interrupt is not used (see Section 6.3 “Data Memory Organization”), the user may need to save the WREG, STATUS and BSR registers on entry to the Interrupt Service Routine (ISR). Depending on the user’s application, other registers also may need to be saved. Example 10-1 saves and restores the WREG, STATUS and BSR registers during an Interrupt Service Routine. EXAMPLE 10-1: MOVWF MOVFF MOVFF ; ; USER ; MOVFF MOVF MOVFF SAVING STATUS, WREG AND BSR REGISTERS IN RAM W_TEMP STATUS, STATUS_TEMP BSR, BSR_TEMP ; W_TEMP is in virtual bank ; STATUS_TEMP located anywhere ; BSR_TMEP located anywhere ISR CODE BSR_TEMP, BSR W_TEMP, W STATUS_TEMP, STATUS DS30000575C-page 196 ; Restore BSR ; Restore WREG ; Restore STATUS  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 11.0 I/O PORTS 11.1 Depending on the device selected and features enabled, there are up to eleven ports available. Some pins of the I/O ports are multiplexed with an alternate function from the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin. Each port has three memory mapped registers for its operation: • TRIS register (Data Direction register) • PORT register (reads the levels on the pins of the device) • LAT register (Output Latch register) Reading the PORT register reads the current status of the pins, whereas writing to the PORT register, writes to the Output Latch (LAT) register. Setting a TRIS bit (= 1) makes the corresponding PORT pin an input (putting the corresponding output driver in a High-Impedance mode). Clearing a TRIS bit (= 0) makes the corresponding port pin an output (i.e., driving the contents of the corresponding LAT bit on the selected pin). The Output Latch (LAT register) is useful for readmodify-write operations on the value that the I/O pins are driving. Read-modify-write operations on the LAT register read and write the latched output value for the PORT register. A simplified model of a generic I/O port, without the interfaces to other peripherals, is shown in Figure 11-1. FIGURE 11-1: GENERIC I/O PORT OPERATION RD LAT Data Bus WR LAT or PORT D I/O Port Pin Capabilities When developing an application, the capabilities of the port pins must be considered. The Absolute Maximum Ratings of the I/O pins are as follows: • RA2, RA3 = -300mV to (VDD + 300 mV) • RA6, RA7, RC0, RC1 = -300 mV to (VDD +300 mV)(1) • RF3/RF4 (the USB D+/D- pins) = supports “USB specific levels” (e.g.: -1.0V to +4.6V, but only when the external source impedance is >/= 28 ohms, and the VUSB3V3 pin voltage is >/= 3.0V, otherwise: -500 mV to (VUSB3V3 +500 mV) • All other general purpose I/O pins (including MCLR), when VDD is < 2.0V: -300 mV to +4.0V. • All other general purpose I/O pins (including MCLR), when VDD is >= 2.0V: -300 mV to +6.0V(2). Note 1: When the pins are used to drive a crystal or ceramic resonator, natural oscillation waveforms slightly exceeding the -300 mV to (VDD +300 mV) range may sometimes occur, and if present, such waveforms are allowed. If these pins are instead used as general purpose inputs, the external driving source should adhere to the -300 mV to (VDD +300 mV) specification. 2: In addition to the above absolute maximums, any I/O pin voltage that is actively selected at runtime by the ADC channel select MUX must also meet the VAIN requirements (parameter A25 in Table 30-40). Q I/O Pin CKx Data Latch D WR TRIS Q CKx TRIS Latch Input Buffer RD TRIS Q D EN RD PORT  2012-2016 Microchip Technology Inc. DS30000575C-page 197 PIC18F97J94 FAMILY 11.1.1 OUTPUT PIN DRIVE When used as digital I/O, the output pin drive strengths vary, according to the pins’ grouping, to meet the needs for a variety of applications. In general, there are two classes of output pins in terms of drive capability: • Outputs designed to drive higher current loads, such as LEDs: - PORTB - PORTC • Outputs with lower drive levels, but capable of driving normal digital circuit loads with a high input impedance. Able to drive LEDs, but only those with smaller current requirements: - PORTA - PORTD - PORTE - PORTF - PORTG - PORTH(1) - PORTJ(1) - PORTK(2) (2) - PORTL Note 1: These ports are not available on 64-pin devices. 2: These ports are not available on 64-pin or 80-pin devices. 11.1.2 PULL-UP CONFIGURATION Nine of the I/O ports (all ports except PORTA and PORTC) implement configurable weak pull-ups on all pins. These are internal pull-ups that allow floating digital input signals to be pulled to a consistent level without the use of external resistors. Pull-ups for PORTB are enabled by clearing the RBPU bit (INTCON2). PORTB pull-ups are individually selectable through the WPUB register. Pull-ups for PORTD, PORTE, PORTF, PORTG, PORTH, PORTJ, PORTK and PORTL are enabled through their corresponding enable bits in the PADCFG register, but are not pin-selectable. DS30000575C-page 198  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 11-1: PADCFG1: PAD CONFIGURATION REGISTER 1(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RDPU REPU RFPU RGPU RHPU RJPU RKPU RLPU bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 RDPU: PORTD Pull-up Enable bit 1 = PORTD pull-ups are enabled for any input pad 0 = All PORTD pull-ups are disabled bit 6 REPU: PORTE Pull-up Enable bit 1 = PORTE pull-ups are enabled for any input pad 0 = All PORTE pull-ups are disabled bit 5 RFPU: PORTF Pull-up Enable bit 1 = PORTF pull-ups are enabled for any input pad 0 = All PORTF pull-ups are disabled bit 4 RGPU: PORTG Pull-up Enable bit 1 = PORTG pull-ups are enabled for any input pad 0 = All PORTG pull-ups are disabled bit 3 RHPU: PORTH Pull-up Enable bit 1 = PORTH pull-ups are enabled for any input pad 0 = All PORTH pull-ups are disabled bit 2 RJPU: PORTJ Pull-up Enable bit 1 = PORTJ pull-ups are enabled for any input pad 0 = All PORTJ pull-ups are disabled bit 1 RKPU: PORTK Pull-up Enable bit 1 = PORTK pull-ups are enabled for any input pad 0 = All PORTK pull-ups are disabled bit 0 RLPU: PORTL Pull-up Enable bit 1 = PORTL pull-ups are enabled for any input pad 0 = All PORTL pull-ups are disabled Note 1: x = Bit is unknown If a particular PORT is not available on a package, the corresponding RnPU register bit will be unimplemented and read back as ‘0’.  2012-2016 Microchip Technology Inc. DS30000575C-page 199 PIC18F97J94 FAMILY 11.1.3 OPEN-DRAIN OUTPUTS FIGURE 11-2: The output pins for several peripherals are also equipped with a configurable, open-drain output option. This allows the peripherals to communicate with external digital logic, operating at a higher voltage level, without the use of level translators. USING THE OPEN-DRAIN OUTPUT (USART SHOWN AS EXAMPLE) 3.3V +5V PIC18F97J94 The open-drain option is implemented on the EUSARTs, the MSSPx modules (in SPI mode) and the CCP modules. These modules are assigned to an I/O pin using the PPS (Peripheral Pin Select) feature. The open-drain option is enabled by setting the open-drain control bits in the ODCON1 and ODCON2 registers. VDD TXX (at logic ‘1’) 3.3V 5V When the open-drain option is required, the output pin must also be tied through an external pull-up resistor, provided by the user, to a higher voltage level, up to 5V (Figure 11-2). When a digital logic high signal is output, it is pulled up to the higher voltage level. REGISTER 11-2: ODCON1: PERIPHERAL OPEN-DRAIN CONTROL REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCP2OD ECCP1OD USART4OD USART3OD USART2OD USART1OD SSP2OD SSP1OD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 ECCP2OD: ECCP2 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 6 ECCP1OD: ECCP1 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 5 USART4OD: EUSART4 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 4 USART3OD: EUSART3 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 3 USART2OD: EUSART2 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 2 USART1OD: EUSART1 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 1 SSP2OD: Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 0 SSP1OD: SPI1 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled DS30000575C-page 200 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 11-3: ODCON2: PERIPHERAL OPEN-DRAIN CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CCP10OD CCP9OD CCP8OD CCP7OD CCP6OD CCP5OD CCP4OD ECCP3OD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 CCP10OD: CCP10 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 6 CCP9OD: CCP9 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 5 CCP8OD: CCP8 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 4 CCP7OD: CCP7 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 3 CCP6OD: CCP6 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 2 CCP5OD: CCP5 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 1 CCP4OD: CCP4 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled bit 0 ECCP3OD: ECCP3 Open-Drain Output Enable bit 1 = Open-drain capability is enabled 0 = Open-drain capability is disabled 11.1.4 ANALOG AND DIGITAL PORTS Many of the ports multiplex analog and digital functionality, providing a lot of flexibility for hardware designers. PIC18FXXJ94 devices can make any analog pin analog or digital, depending on an application’s needs. The ports’ analog/digital functionality is controlled by the registers: ANCON1, ANCON2 and ANCON3.  2012-2016 Microchip Technology Inc. x = Bit is unknown Setting these registers makes the corresponding pins analog and clearing the registers makes the ports digital. For details on these registers, see Section 22.0 “12-Bit A/D Converter with Threshold Scan” DS30000575C-page 201 PIC18F97J94 FAMILY 11.2 PORTA, LATA and TRISA Registers PORTA is an 8-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are TRISA and LATA. All PORTA pins have Schmitt Trigger input levels and full CMOS output drivers. RA are multiplexed with analog inputs for the A/D Converter. The operation of the analog inputs as A/D Converter inputs is selected by clearing or setting the ANSELx control bits in the ANCON1 register. The corresponding TRISA bits control the direction of these pins, even when they are being used as analog inputs. The user must ensure the bits in the TRISA register are maintained set when using them as analog inputs. Note: RA are configured as analog inputs on any Reset and are read as ‘0’. TABLE 11-1: EXAMPLE 11-1: CLRF PORTA CLRF LATA BANKSEL MOVLW MOVWF BANKSEL MOVLW ANCON1 00h ANCON1 TRISA 0BFh MOVWF TRISA INITIALIZING PORTA ; ; ; ; ; ; ; ; ; ; ; ; Initialize PORTA by clearing output latches Alternate method to clear output data latches Select bank with ANCON1 register Configure A/D for digital inputs Select bank with TRISA register Value used to initialize data direction Set RA as inputs, RA as output PORTA FUNCTIONS Pin Name RA0/AN0/AN1-/RP0/ SEG19 RA1/AN1/RP1/SEG18 RA2/AN2/VREF-/RP2/ SEG21 Legend: OSC2/CLKO/RA6 and OSC1/CLKI/RA7 normally serve as the external circuit connections for the External (Primary) Oscillator circuit (HS Oscillator modes), or the external clock input and output (EC Oscillator modes). In these cases, RA6 and RA7 are not available as digital I/O, and their corresponding TRIS and LAT bits are read as ‘0’. When the device is configured to use either the FRC or LPRC Internal Oscillators as the default oscillator mode, RA6 and RA7 are automatically configured as digital I/O; the oscillator and clock in/ clock out functions are disabled. Function TRIS Setting I/O I/O Type RA0 0 O DIG Description LATA data output; not affected by analog input. 1 I ST AN0 1 I ANA A/D Input Channel 0. Default input configuration on POR; does not affect digital output. PORTA data input; disabled when analog input is enabled. AN1- 1 I ANA Quasi-differential A/D negative input channel. RP0 x x DIG Reconfigurable Pin 0 for PPS-Lite; TRIS must be set to match input/output of the module. SEG19 0 O ANA LCD Segment 19 output; disables all other pin functions. RA1 0 O DIG LATA data output; not affected by analog input. 1 I ST PORTA data input; disabled when analog input is enabled. AN1 1 I ANA A/D Input Channel 1. Default input configuration on POR; does not affect digital output. RP1 x x DIG Reconfigurable Pin 1 for PPS-Lite; TRIS must be set to match input/output of module. LCD Segment 18 output; disables all other pin functions. SEG18 0 O ANA RA2 0 O DIG LATA data output; not affected by analog input. 1 I ST PORTA data input; disabled when analog input enabled. AN2 1 I ANA A/D Input Channel 2. Default input configuration on POR; does not affect digital output. VREF- 1 I ANA A/D and Comparator Low Reference Voltage input. RP2 x x DIG Reconfigurable Pin 2 for PPS-Lite; TRIS must be set to match input/output of module. SEG21 0 O ANA LCD Segment 21 output; disables all other pin functions. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 202  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-1: PORTA FUNCTIONS (CONTINUED) Pin Name RA3/AN3/VREF+/RP3 RA4/AN6/RP4/SEG14 RA5/AN4/RP5/LVDIN/ C1INA/C2INA/C3INA/ SEG15 RA6/RP6/CLKO/OSC2 RA7/RP10/CLKI/OSC1 Legend: Function TRIS Setting I/O I/O Type RA3 0 O DIG LATA data output; not affected by analog input. 1 I ST PORTA data input; disabled when analog input is enabled. AN3 1 I ANA A/D Input Channel 3. Default input configuration on POR; does not affect digital output. VREF+ 1 I ANA A/D and Comparator High Reference Voltage input. RP3 x x DIG Reconfigurable Pin 3 for PPS-Lite; TRIS must be set to match input/output of module. RA4 0 O DIG LATA data output; not affected by analog input. 1 I ST PORTA data input; disabled when analog input is enabled. AN6 1 I ANA A/D Input Channel 6. Default input configuration on POR; does not affect digital output. RP4 x x DIG Reconfigurable Pin 4 for PPS-Lite; TRIS must be set to match input/output of module. SEG14 0 O ANA LCD Segment 14 output; disables all other pin functions. RA5 0 O DIG LATA data output; not affected by analog input. 1 I ST PORTA data input; disabled when analog input is enabled. AN4 1 I ANA A/D Input Channel 4. Default input configuration on POR; does not affect digital output. RP5 x x DIG Reconfigurable Pin 5 for PPS-Lite; TRIS must be set to match input/output of module. LVDIN 1 I ANA High/Low-Voltage Detect (HLVD) external trip point input. C1INA 1 I ANA Comparator 1 Input A. Description C2INA 1 I ANA Comparator 2 Input A. C3INA 1 I ANA Comparator 3 Input A. SEG15 0 O ANA LCD Segment 15 output; disables all other pin functions. RA6 0 O DIG LATA data output; disabled when OSC2 Configuration bit is set. 1 I ST PORTA data input; disabled when OSC2 Configuration bit is set. RP6 x x DIG Reconfigurable Pin 6 for PPS-Lite; TRIS must be set to match input/output of module. CLKO x O DIG System cycle clock output (FOSC/4, EC and Internal Oscillator modes). OSC2 x O ANA Main oscillator feedback output connection (HS, MS and LP modes). RA7 0 O DIG LATA data output; disabled when OSC2 Configuration bit is set. 1 I ST PORTA data input; disabled when OSC2 Configuration bit is set. RP10 x x DIG Reconfigurable Pin 10 for PPS-Lite; TRIS must be set to match input/output of module. CLKI x O DIG Main external clock source input (EC modes). OSC1 x O ANA Main oscillator input connection (HS, MS and LP modes). O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 203 PIC18F97J94 FAMILY 11.3 PORTB, LATB and TRISB Registers PORTB is an 8-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are TRISB and LATB. All pins on PORTB are digital only. EXAMPLE 11-2: CLRF PORTB CLRF LATB MOVLW 0CFh MOVWF TRISB TABLE 11-2: INITIALIZING PORTB ; ; ; ; ; ; ; ; ; ; ; ; The RB pins are multiplexed as CTMU edge inputs. Initialize PORTB by clearing output data latches Alternate method to clear output data latches Value used to initialize data direction Set RB as inputs RB as outputs RB as inputs PORTB FUNCTIONS Pin Name RB0/INT0/CTED13/ RP8/VLCAP1 RB1/RP9/VLCAP2 RB2/CTED1/RP14/ SEG9 RB3/CTED2/RP7/ SEG10 Legend: Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit, RBPU (INTCON2), and setting the associated WPUB bit. The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. Function TRIS Setting I/O I/O Type RB0 0 O DIG LATB data output. 1 I ST PORTB data input. External Interrupt 0 input. Description INT0 1 I ST CTED13 1 I ST CTMU Edge 13 input. RP8 x x DIG Reconfigurable Pin 8 for PPS-Lite; TRIS must be set to match input/output of module. VLCAP1 x x ANA External capacitor connection for LCD module. RB1 0 O DIG LATB data output. 1 I ST PORTB data input. RP9 x x DIG Reconfigurable Pin 9 for PPS-Lite; TRIS must be set to match input/output of module. VLCAP2 x x ANA External capacitor connection for LCD module. RB2 0 O DIG LATB data output. 1 I ST PORTB data input. CTED1 1 I ST CTMU Edge 1 input. RP14 x x DIG Reconfigurable Pin 14 for PPS-Lite; TRIS must be set to match input/output of module. SEG9 0 O ANA LCD Segment 9 output; disables all other pin functions. RB3 0 O DIG LATB data output. PORTB data input. 1 I ST CTED2 1 I ST CTMU Edge 2 input. RP7 x x DIG Reconfigurable Pin 7 for PPS-Lite; TRIS must be set to match input/output of module. SEG10 0 O ANA LCD Segment 10 output; disables all other pin functions. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 204  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-2: Pin Name RB4/CTED3/RP12/ SEG11 RB5/CTED4/RP13/ SEG8 RB6/CTED5/PGC RB7/CTED6/PGD Legend: PORTB FUNCTIONS (CONTINUED) Function TRIS Setting I/O I/O Type RB4 0 O DIG LATB data output. 1 I ST PORTB data input. CTED3 1 I ST CTMU Edge 3 input. RP12 x x DIG Reconfigurable Pin 12 for PPS-Lite; TRIS must be set to match input/output of module. SEG11 0 O ANA LCD Segment 11 output; disables all other pin functions. RB5 0 O DIG LATB data output. PORTB data input. Description 1 I ST CTED4 1 I ST CTMU Edge 4 input. RP13 x x DIG Reconfigurable Pin 13 for PPS-Lite; TRIS must be set to match input/output of module. SEG8 0 O ANA LCD Segment 8 output; disables all other pin functions. RB6 0 O DIG LATB data output. 1 I ST PORTB data input. CTED5 1 I ST CTMU Edge 5 input. PGC x I ST Serial execution (ICSP™) clock input for ICSP and ICD operations. RB7 0 O DIG LATB data output. 1 I ST PORTB data input. CTED6 1 I ST CTMU Edge 6 input. PGD x I/O ST/DIG Serial execution (ICSP™) data input/output for ICSP and ICD operations. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 205 PIC18F97J94 FAMILY 11.4 PORTC, LATC and TRISC Registers PORTC is an 8-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are TRISC and LATC. Only PORTC pins, RC2 through RC7, are digital only pins. The pins have Schmitt Trigger input buffers. The contents of the TRISC register are affected by peripheral overrides. Reading TRISC always returns the current contents, even though a peripheral device may be overriding one or more of the pins. EXAMPLE 11-3: When enabling peripheral functions, use care in defining TRIS bits for each PORTC pin. Some peripherals can override the TRIS bit to make a pin an output or input. Consult the corresponding peripheral section for the correct TRIS bit settings. Note: These pins are configured as digital inputs on any device Reset. TABLE 11-3: CLRF PORTC CLRF LATC MOVLW 0CFh MOVWF TRISC INITIALIZING PORTC ; ; ; ; ; ; ; ; ; ; ; ; Initialize PORTC by clearing output data latches Alternate method to clear output data latches Value used to initialize data direction Set RC as inputs RC as outputs RC as inputs PORTC FUNCTIONS Pin Name Function TRIS Setting I/O I/O Type RC0/ PWRLCLK/ SCLKI/SOSCO RC0 1 I ST PORTC data input. PWRLCLK 1 I ST Optional RTCC input from power line clock (50 or 60 Hz). ST Digital SOSC input. RC1/SOSCI RC2/CTED7/ RP11/AN9/ SEG13 RC3/CTED8/ RP15/SCL1/ SEG17 RC4/CTED9/ RP17/SDA1/ SEG16 Legend: SCLKI x I SOSCO x O Description ANA Secondary Oscillator (SOSC) feedback output connection. RC1 1 I SOSCI x I ANA Secondary Oscillator (SOSC) input connection. ST PORTC data input. RC2 0 O DIG LATC data output; not affected by analog input. 1 I ST PORTC data input; disabled when analog input is enabled. CTED7 1 I ST CTMU Edge 7 input. RP11 x x DIG Reconfigurable Pin 11 for PPS-Lite; TRIS must be set to match input/output of module. AN9 1 I ANA A/D Input Channel 9. Default input configuration on POR; does not affect digital output. SEG13 0 O ANA LCD Segment 13 output; disables all other pin functions. RC3 0 O DIG LATC data output. 1 I ST PORTC data input. CTED8 1 I ST CTMU Edge 8 input. RP15 x x DIG Reconfigurable Pin 15 for PPS-Lite; TRIS must be set to match input/output of module. SCL1 x I/O I2C Synchronous serial clock input/output for I2C mode. SEG17 0 O ANA LCD Segment 17 output; disables all other pin functions RC4 0 O DIG LATC data output. 1 I ST PORTC data input. CTED9 1 I ST CTMU Edge 9 input. RP17 x x DIG Reconfigurable Pin 17 for PPS-Lite; TRIS must be set to match input/output of module. SDA1 x I/O I2C I2C mode data I/O SEG16 0 O ANA LCD Segment 16 output; disables all other pin functions. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, I2C = I2C/SMBus, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 206  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-3: Pin Name RC5/CTED10/ RP16/SEG12 RC6/CTED11/ UOE/RP18/ SEG27 RC7/CTED12/ RP19/SEG22 Legend: PORTC FUNCTIONS (CONTINUED) Function TRIS Setting I/O I/O Type RC5 0 O DIG LATC data output. 1 I ST PORTC data input. CTED10 1 I ST CTMU Edge 10 input. RP16 x x DIG Reconfigurable Pin 16 for PPS-Lite; TRIS must be set to match input/output of module. Description SEG12 0 O ANA LCD Segment 12 output; disables all other pin functions. RC6 0 O DIG LATC data output. 1 I ST PORTC data input. CTED11 1 I ST CTMU Edge 11 input. UOE 0 O DIG USB Output Enable control (for external transceiver). RP18 x x DIG Reconfigurable Pin 18 for PPS-Lite; TRIS must be set to match input/output of module. SEG27 0 O ANA LCD Segment 27 output; disables all other pin functions. RC7 0 O DIG LATC data output. PORTC data input. 1 I ST CTED12 1 I ST CTMU Edge 12 input. RP19 x x DIG Reconfigurable Pin 19 for PPS-Lite; TRIS must be set to match input/output of module. SEG22 0 O ANA LCD Segment 22 output; disables all other pin functions. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, I2C = I2C/SMBus, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 207 PIC18F97J94 FAMILY 11.5 PORTD, LATD and TRISD Registers PORTD is the low-order byte of the multiplexed Address/Data bus (AD). The TRISD bits are also overridden. PORTD is an 8-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are TRISD and LATD. All pins on PORTD are implemented with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. Note: These pins are configured as digital inputs on any device Reset. PORTD also has I2C functionality on RD5 and RD6. EXAMPLE 11-4: Each of the PORTD pins has a weak internal pull-up. A single control bit can turn off all the pull-ups. This is performed by setting bit, RDPU (PADCFG). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on all device Resets. On 80-pin and 100-pin devices, PORTD is multiplexed with the system bus as part of the external memory interface. I/O port and other functions are only available when the interface is disabled by setting the EBDIS bit (MEMCON). When the interface is enabled, TABLE 11-4: PORTD can also be configured as an 8-bit wide microprocessor port (Parallel Slave Port) by setting control bit, PSPMODE (PSPCON). In this mode, the input buffers are TTL. For additional information, see Section 11.13 “Parallel Slave Port”. CLRF PORTD CLRF LATD MOVLW 0CFh MOVWF TRISD Function TRIS Setting I/O I/O Type RD0/PSP0/ RP20/SEG0/AD0 RD0 0 O DIG LATD data output. 1 I ST PORTD data input. PSP0 x I/O RP20 x x SEG0 0 O AD0 x I/O RD1 0 O DIG LATD data output. 1 I ST PORTD data input. PSP1 x I/O RP21 x x SEG1 0 O AD1 x I/O RD2 0 O DIG LATD data output. 1 I ST PORTD data input. PSP2 x I/O RP22 x x SEG2 0 O AD2 x I/O RD2/PSP2/ RP22/SEG2/AD2 Legend: ; ; ; ; ; ; ; ; ; ; ; ; Initialize PORTD by clearing output data latches Alternate method to clear output data latches Value used to initialize data direction Set RD as inputs RD as outputs RD as inputs PORTD FUNCTIONS Pin Name RD1/PSP1/ RP21/SEG1/AD1 INITIALIZING PORTD Description ST/DIG Parallel Slave Port Data Bus Bit 0. DIG Reconfigurable Pin 20 for PPS-Lite; TRIS must be set to match input/ output of module. ANA LCD Segment 0 output; disables all other pin functions. ST/DIG External Memory Bus Address Line 0. ST/DIG Parallel Slave Port Data Bus Bit 1. DIG Reconfigurable Pin 21 for PPS-Lite; TRIS must be set to match input/ output of module. ANA LCD Segment 1 output; disables all other pin functions. ST/DIG External Memory Bus Address Line 1. ST/DIG Parallel Slave Port Data Bus Bit 2. DIG Reconfigurable Pin 22 for PPS-Lite; TRIS must be set to match input/ output of module. ANA LCD Segment 2 output; disables all other pin functions. ST/DIG External Memory Bus Address Line 2. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, I2C = I2C/SMBus, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 208  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-4: PORTD FUNCTIONS (CONTINUED) Pin Name Function TRIS Setting I/O I/O Type RD3/PSP3/ RP23/SEG3/AD3 RD3 0 O DIG LATD data output. 1 I ST PORTD data input. PSP3 x I/O RP23 x x RD4/PSP4/ RP24/SEG4/AD4 RD5/PSP5/ RP25/SDA2/ SEG5/AD5 RD6/PSP6/ RP26/SCL2/ SEG6/AD6 RD7/PSP7/ RP27/REFO2/ SEG7/AD7 Legend: Description ST/DIG Parallel Slave Port Data Bus Bit 3. DIG Reconfigurable Pin 23 for PPS-Lite; TRIS must be set to match input/ output of module. ANA LCD Segment 3 output; disables all other pin functions. SEG3 0 O AD3 x I/O RD4 0 O DIG LATD data output. 1 I ST PORTD data input. PSP4 x I/O RP24 x x ST/DIG External Memory Bus Address Line 3. ST/DIG Parallel Slave Port Data Bus Bit 4. DIG Reconfigurable Pin 24 for PPS-Lite; TRIS must be set to match input/ output of module. ANA LCD Segment 4 output; disables all other pin functions. SEG4 0 O AD4 x I/O RD5 0 O DIG LATD data output. 1 I ST PORTD data input. PSP5 x I/O RP25 x x SDA2 x I/O SEG5 0 O AD5 x I/O RD6 0 O DIG LATD data output. 1 I ST PORTD data input. PSP6 x I/O RP26 x x DIG Reconfigurable Pin 26 for PPS-Lite; TRIS must be set to match input/ output of module. SCL2 x I/O I2C Synchronous serial clock input/output for I2C mode. SEG6 0 O AD6 x I/O RD7 0 O DIG LATD data output. 1 I ST PORTD data input. PSP7 x I/O RP27 x x ST/DIG External Memory Bus Address Line 4. ST/DIG Parallel Slave Port Data Bus Bit 5. DIG Reconfigurable Pin 25 for PPS-Lite; TRIS must be set to match input/ output of module. ST/DIG I2C mode data I/O. ANA LCD Segment 5 output; disables all other pin functions. ST/DIG External Memory Bus Address Line 5. ST/DIG Parallel Slave Port Data Bus Bit 6. ANA LCD Segment 6 output; disables all other pin functions. ST/DIG External Memory Bus Address Line 6. ST/DIG Parallel Slave Port Data Bus Bit 7. DIG Reconfigurable Pin 27 for PPS-Lite; TRIS must be set to match input/ output of module. REFO2 0 O DIG Reference Clock 2 output. SEG7 0 O ANA LCD Segment 7 output; disables all other pin functions. AD7 x I/O ST/DIG External Memory Bus Address Line 7. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, I2C = I2C/SMBus, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 209 PIC18F97J94 FAMILY 11.6 PORTE, LATE and TRISE Registers PORTE is also multiplexed with the Parallel Slave Port address lines. RE2, RE1 and RE0 are multiplexed with the control signals, CS, WR and RD. PORTE is an 8-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are TRISE and LATE. All pins on PORTE are implemented with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. Note: These pins are configured as digital inputs on any device Reset. Each of the PORTE pins has a weak internal pull-up. A single control bit can turn off all the pull-ups. This is performed by setting bit, REPU (PADCFG). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on any device Reset. RE3 can also be configured as the Reference Clock Output (REFO) from the system clock. For further details, see Section 3.4 “Reference Clock Output Control Module”. EXAMPLE 11-5: CLRF PORTE CLRF LATE MOVLW 03h MOVWF TRISE For devices operating in Microcontroller mode, the RE7 pin can be configured as the alternate peripheral pin for the ECCP2 module and Enhanced PWM Output 2A. TABLE 11-5: Pin Name RE0//RD/RP28/ LCDBIAS1/AD8 RE1//WR/RP29/ LCDBIAS2/AD9 RE2/CS/RP30/ LCDBIAS3/AD10 Legend: INITIALIZING PORTE ; ; ; ; ; ; ; ; ; ; ; Initialize PORTE by clearing output data latches Alternate method to clear output data latches Value used to initialize data direction Set RE as inputs RE as outputs PORTE FUNCTIONS Function TRIS Setting I/O I/O Type RE0 0 O DIG LATE data output. 1 I ST PORTE data input. Description RD 1 I ST Parallel Slave Port (PSP) Read (RD) signal. RP28 x x DIG Reconfigurable Pin 28 for PPS-Lite; TRIS must be set to match input/ output of module. LCDBIAS1 x I ANA LCD Module Bias Voltage Input 1. AD8 x I/O RE1 0 O DIG LATE data output. PORTE data input. ST/DIG External Memory Bus Address Line 8. 1 I ST WR 1 I ST Parallel Slave Port (PSP) Write (WR) signal. RP29 x x DIG Reconfigurable Pin 29 for PPS-Lite; TRIS must be set to match input/ output of module. LCDBIAS2 x I ANA LCD Module Bias Voltage Input 2. AD9 x I/O RE2 0 O DIG LATE data output. 1 I ST PORTE data input. ST/DIG External Memory Bus Address Line 9. CS 1 I ST Parallel Slave Port (PSP) Chip Select (CS) signal. RP30 x x DIG Reconfigurable Pin 30 for PPS-Lite; TRIS must be set to match input/ output of module. LCDBIAS3 x I ANA LCD Module Bias Voltage Input 3. AD10 x I/O ST/DIG External Memory Bus Address Line 10. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 210  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-5: Pin Name RE3/REFO1/ RP33/COM0/ AD11 RE4/RP32/ COM1/AD12 RE5/RP37/ COM2/AD13 RE6/RP34/ COM3/AD14 RE7/RP31/ LCDBIAS0/ AD15 Legend: PORTE FUNCTIONS (CONTINUED) Function TRIS Setting I/O I/O Type RE3 0 O DIG 1 I ST PORTE data input. REFO1 0 O DIG Reference Clock Output 1. RP33 x x DIG Reconfigurable Pin 33 for PPS-Lite; TRIS must be set to match input/ output of module. ANA LCD Common 0 output; disables all other outputs. Description LATE data output. COM0 x O AD11 x I/O RE4 0 O DIG 1 I ST PORTE data input. RP32 x x DIG Reconfigurable Pin 32 for PPS-Lite; TRIS must be set to match input/ output of module. COM1 x O ANA LCD Common 1 output; disables all other outputs. AD12 x I/O RE5 0 O ST/DIG External Memory Bus Address Line 11. LATE data output. ST/DIG External Memory Bus Address Line 12. DIG LATE data output. 1 I ST PORTE data input. RP37 x x DIG Reconfigurable Pin 37 for PPS-Lite; TRIS must be set to match input/ output of module. COM2 x O ANA LCD Common 2 output; disables all other outputs. AD13 x I/O RE6 0 O DIG LATE data output. 1 I ST PORTE data input. RP34 x x DIG Reconfigurable Pin 34 for PPS-Lite; TRIS must be set to match input/ output of module. COM3 x O ANA LCD Common 3 output; disables all other outputs. AD14 x I/O RE7 0 O DIG 1 I ST PORTE data input. RP31 x x DIG Reconfigurable Pin 31 for PPS-Lite; TRIS must be set to match input/ output of module. LCDBIAS0 x I ANA LCD Module Bias Voltage Input 0. AD15 x I/O ST/DIG External Memory Bus Address Line 13. ST/DIG External Memory Bus Address Line 14. LATE data output. ST/DIG External Memory Bus Address Line 15. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 211 PIC18F97J94 FAMILY 11.7 PORTF, LATF and TRISF Registers EXAMPLE 11-6: PORTF is a 6-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are TRISF and LATF. All pins on PORTF are implemented with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. CLRF PORTF CLRF LATF Pins, RF2 through RF6, may be used as comparator inputs or outputs by setting the appropriate bits in the CMCON register. To use RF as digital inputs, it is also necessary to turn off the comparators. BANKSEL ANCON1 MOVLW BFh MOVWF ANCON1 BANKSELANCON2; MOVLW F1h MOVWF ANCON2 BANKSEL TRISF MOVLW 0F3h Note 1: On device Resets, pins, RF, are configured as analog inputs and are read as ‘0’. 2: To configure PORTF as a digital I/O, turn off the comparators and clear ANCON1 and ANCON2 to digital. TABLE 11-6: MOVWF INITIALIZING PORTF TRISF ; ; ; ; ; ; ; ; ; Initialize PORTF by clearing output data latches Alternate method to clear output data latches Select bank with ANCON1 register Make RF2 digital ; ; ; ; ; ; ; ; Make RF5, RF6, RF7 digital Select bank with TRISF register Value used to initialize data direction Set RF3:RF2 as outputs RF7:RF4 as inputs PORTF FUNCTIONS Function TRIS Setting I/O I/O Type RF0 — — — — PORTF is not implemented. RF1 — — — — PORTF is not implemented. RF2 0 O DIG 1 I ST PORTF data input. RP36 x x DIG Reconfigurable Pin 36 for PPS-Lite; TRIS must be set to match input/ output of module. Pin Name RF2/RP36/C2INB/ CTMUI/SEG20/ AN7 RF3/D- RF4/D+ RF5/RP35/C1INB/ AN10/CVREF/ SEG23 Legend: Description LATF data output. C2INB 1 I ANA Comparator 2 Input B. CTMUI 1 I ANA CTMU comparator input. SEG20 0 O ANA LCD Segment 20 output; disables all other pin functions. AN7 1 I ANA A/D Input Channel 7. Default input configuration on POR; does not affect digital output. RF3 1 I ST D- x I XCVR USB bus minus line output. x O XCVR USB bus minus line input. RF4 1 I ST PORTF data input. D+ x I XCVR USB bus plus line input. x O XCVR USB bus plus line output. RF5 0 O DIG 1 I ST PORTF data input. RP35 x x DIG Reconfigurable Pin 35 for PPS-Lite; TRIS must be set to match input/ output of module. C1INB 1 I ANA Comparator 1 Input B. AN10 1 I ANA A/D Input Channel 10. Default input configuration on POR; does not affect digital output. CVREF 0 O ANA Comparator reference voltage output. SEG23 0 O ANA LCD Segment 23 output; disables all other pin functions. PORTF data input. LATF data output. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, XCVR = USB Transceiver, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 212  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-6: PORTF FUNCTIONS (CONTINUED) Pin Name Function TRIS Setting I/O I/O Type RF6/RP40/C1INA/ AN11/SEG24 RF6 0 O DIG 1 I ST PORTF data input. RP40 x x DIG Reconfigurable Pin 40 for PPS-Lite; TRIS must be set to match input/ output of module. C1INA 1 I ANA Comparator 1 Input A. AN11 1 I ANA A/D Input Channel 11. Default input configuration on POR; does not affect digital output. SEG24 0 O ANA LCD Segment 24 output; disables all other pin functions. RF7 0 O DIG LATF data output. 1 I ST PORTF data input. RP38 x x DIG Reconfigurable Pin 38 for PPS-Lite; TRIS must be set to match input/ output of module. AN5 1 I ANA A/D Input Channel 5. Default input configuration on POR; does not affect digital output. SEG25 0 O ANA LCD Segment 25 output; disables all other pin functions. RF7/RP38/AN5/ SEG25 Legend: Description LATF data output. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, XCVR = USB Transceiver, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 213 PIC18F97J94 FAMILY 11.8 PORTG, LATG and TRISG Registers EXAMPLE 11-7: CLRF PORTG width varies depending on pin count. For 64- and 80-pin devices, PORTG is a 6-bit wide, bidirectional port. For 100-pin devices, PORTG is an 8-bit wide bidirectional port. The corresponding Data Direction and Output Latch registers are TRISG and LATG. PORTG is multiplexed with the EUSART, and CCP, ECCP, Analog, Comparator, RTCC and Timer input functions (Table 11-7). When operating as I/O, all PORTG pins have Schmitt Trigger input buffers. The open-drain functionality for the CCPx and EUSARTx can be configured using ODCONx. When enabling peripheral functions, care should be taken in defining TRIS bits for each PORTG pin. Some peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to make a pin an input. The user should refer to the corresponding peripheral section for the correct TRIS bit settings. The pin override value is not loaded into the TRIS register. This allows read-modify-write of the TRIS register without concern due to peripheral overrides. TABLE 11-7: Function TRIS Setting I/O I/O Type RG0/RP46/AN8/ SEG28/COM4 RG0 0 O DIG RG2/RP42/ C3INA/AN18/ SEG30/COM6 Legend: ; ; ; BCF CM1CON, CON ; ; CLRF LATG ; ; ; BANKSEL ANCON2 ; MOVLW 0F0h ; ; MOVWF ANCON2 BANKSEL TRISG ; MOVLW 04h ; ; ; MOVWF TRISG ; ; ; ; Initialize PORTG by clearing output data latches disable comparator 1 Alternate method to clear output data latches Select bank with ACON2 register make AN16 to AN19 digital Select bank with TRISG register Value used to initialize data direction Set RG1:RG0 as outputs RG2 as input RG4:RG3 as inputs PORTG FUNCTIONS Pin Name RG1/RP39/ AN19/SEG29/ COM5 PORTG INITIALIZING PORTG Description LATG data output; not affected by analog input. 1 I ST PORTG data input; disabled when analog input is enabled. RP46 x x DIG Reconfigurable Pin 46 for PPS-Lite; TRIS must be set to match input/ output of module. AN8 1 I ANA A/D Input Channel 8. Default input configuration on POR; does not affect digital output. SEG28 0 O ANA LCD Segment 28 output; disables all other pin functions. COM4 x O ANA LCD Common 4 output; disables all other outputs. RG1 0 O DIG LATG data output; not affected by analog input. 1 I ST PORTG data input; disabled when analog input is enabled. RP39 x x DIG Reconfigurable Pin 39 for PPS-Lite; TRIS must be set to match input/ output of module. AN19 1 I ANA A/D Input Channel 19. Default input configuration on POR; does not affect digital output. SEG29 0 O ANA LCD Segment 29 output; disables all other pin functions. COM5 x O ANA LCD Common 5 output; disables all other outputs. 0 O DIG LATG data output; not affected by analog input. RG2 1 I ST PORTG data input; disabled when analog input is enabled. RP42 x x DIG Reconfigurable Pin 42 for PPS-Lite; TRIS must be set to match input/ output of module. C3INA 1 I ANA Comparator 3 Input A. AN18 1 I ANA A/D Input Channel 18. Default input configuration on POR; does not affect digital output. SEG30 0 O ANA LCD Segment 30 output; disables all other pin functions. COM6 x O ANA LCD Common 6 output; disables all other outputs. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 214  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-7: Pin Name RG3/RP43/ C3INB/AN17/ SEG31/COM7 RG4/RTCC/ RP44/C3INC/ AN16/SEG26 RG6 RG7 Legend: PORTG FUNCTIONS (CONTINUED) Function TRIS Setting I/O I/O Type RG3 0 O DIG LATG data output; not affected by analog input. 1 I ST PORTG data input; disabled when analog input is enabled. RP43 x x DIG Reconfigurable Pin 43 for PPS-Lite; TRIS must be set to match input/ output of module. C3INB 1 I ANA Comparator 3 Input B. AN17 1 I ANA A/D Input Channel 17. Default input configuration on POR; does not affect digital output. SEG31 0 O ANA LCD Segment 31 output; disables all other pin functions. COM7 x O ANA LCD Common 7 output; disables all other outputs. RG4 0 O DIG LATG data output; not affected by analog input. 1 I ST PORTG data input; disabled when analog input is enabled. RTCC x O DIG RTCC output. RP44 x x DIG Reconfigurable Pin 44 for PPS-Lite; TRIS must be set to match input/ output of module. C3INC 1 I ANA Comparator 3 Input C. AN16 1 I ANA A/D Input Channel 16. Default input configuration on POR; does not affect digital output. SEG26 0 O ANA LCD Segment 26 output; disables all other pin functions. RG6 0 O DIG LATG data output. 1 I ST PORTG data input. 0 O DIG LATG data output. 1 I ST PORTG data input. RG7 Description O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 215 PIC18F97J94 FAMILY 11.9 Note: PORTH, LATH and TRISH Registers EXAMPLE 11-8: PORTH is available only on 80-pin and 100-pin devices. PORTH is an 8-bit wide, bidirectional I/O port. The corresponding Data Direction and Output Latch registers are TRISH and LATH. All pins on PORTH are implemented with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. TABLE 11-8: Pin Name RH0/AN23/ SEG47/A16 RH2/AN21/ SEG45/A18 RH3/AN20/ SEG44/A19 RH4/C2INC/ AN12/SEG40 Legend: PORTH CLRF LATH BANKSEL MOVLW MOVWF MOVLW MOVWF BANKSEL MOVLW ANCON2 0Fh ANCON2 0Fh ANCON1 TRISH 0CFh MOVWF TRISH ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; Initialize PORTH by clearing output data latches Alternate method to clear output data latches Select bank with ANCON2 register Configure PORTH as digital I/O Configure PORTH as digital I/O Select bank with TRISH register Value used to initialize data direction Set RH3:RH0 as inputs RH5:RH4 as outputs RH7:RH6 as inputs PORTH FUNCTIONS Function RH0 RH1/AN22/ SEG46/A17 CLRF INITIALIZING PORTH TRIS Setting I/O I/O Type Description 0 O DIG LATH data output; not affected by analog input. 1 I ST PORTH data input. AN23 1 I ANA A/D Input Channel 23. Default input configuration on POR; does not affect digital output. SEG47 0 O ANA LCD Segment 47 output; disables all other pin functions. A16 x O DIG External Memory Bus Address output. RH1 0 O DIG LATH data output; not affected by analog input. 1 I ST PORTH data input. AN22 1 I ANA A/D Input Channel 22. Default input configuration on POR; does not affect digital output. SEG46 0 O ANA LCD Segment 46 output; disables all other pin functions. A17 x O DIG External Memory Bus Address output. RH2 0 O DIG LATH data output; not affected by analog input. 1 I ST AN21 1 I ANA A/D Input Channel 21. Default input configuration on POR; does not affect digital output. SEG45 0 O ANA LCD Segment 45 output; disables all other pin functions. A18 x O DIG External Memory Bus Address output. RH3 0 O DIG LATH data output; not affected by analog input. 1 I ST PORTH data input. AN20 1 I ANA A/D Input Channel 20. Default input configuration on POR; does not affect digital output. SEG44 0 O ANA LCD Segment 44 output; disables all other pin functions. A19 x O DIG External Memory Bus Address output. RH4 0 O DIG LATH data output; not affected by analog input. 1 I ST PORTH data input; disabled when analog input is enabled. C2INC 1 I ANA Comparator 2 Input C. AN12 1 I ANA A/D Input Channel 12. Default input configuration on POR; does not affect digital output. SEG40 0 O ANA LCD Segment 40 output; disables all other pin functions. PORTH data input. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 216  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-8: Pin Name RH5/C2IND/ AN13/SEG41 RH6/C1INC/ AN14/SEG42 RH7/AN15/ SEG43 Legend: PORTH FUNCTIONS (CONTINUED) Function RH5 TRIS Setting I/O I/O Type 0 O DIG LATH data output; not affected by analog input. 1 I ST PORTH data input; disabled when analog input is enabled. Description C2IND 1 I ANA Comparator 2 Input D. AN13 1 I ANA A/D Input Channel 13. Default input configuration on POR; does not affect digital output. SEG41 0 O ANA LCD Segment 41 output; disables all other pin functions. RH6 0 O DIG LATH data output; not affected by analog input. 1 I ST C1INC 1 I ANA Comparator 1 Input C. AN14 1 I ANA A/D Input Channel 14. Default input configuration on POR; does not affect digital output. SEG42 0 O ANA LCD Segment 42 output; disables all other pin functions. RH7 0 O DIG LATH data output; not affected by analog input. 1 I ST PORTH data input; disabled when analog input is enabled. AN15 1 I ANA A/D Input Channel 15. Default input configuration on POR; does not affect digital output. SEG43 0 O ANA LCD Segment 43 output; disables all other pin functions. PORTH data input; disabled when analog input is enabled. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 217 PIC18F97J94 FAMILY 11.10 PORTJ, LATJ and TRISJ Registers Note: PORTJ is available only on 80-pin and 100-pin devices. PORTJ is an 8-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are TRISJ and LATJ. All pins on PORTJ are implemented with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. Note: These pins are configured as digital inputs on any device Reset. When the external memory interface is enabled, all of the PORTJ pins function as control outputs for the interface. This occurs automatically when the interface is enabled by clearing the EBDIS control bit (MEMCON). The TRISJ bits are also overridden. TABLE 11-9: Pin Name RJ0/SEG32/ ALE RJ1/SEG33/OE RJ3/SEG35/ WRH RJ4/SEG39/ BA0 RJ5/SEG38/CE Legend: EXAMPLE 11-9: CLRF PORTJ CLRF LATJ MOVLW 0CFh MOVWF TRISJ INITIALIZING PORTJ ; ; ; ; ; ; ; ; ; ; Initialize PORTJ by clearing output latches Alternate method to clear output latches Value used to initialize data direction Set RJ3:RJ0 as inputs RJ5:RJ4 as output RJ7:RJ6 as inputs PORTJ FUNCTIONS Function TRIS Setting I/O I/O Type RJ0 0 O DIG 1 I ST SEG32 0 O ANA LCD Segment 32 output; disables all other pin functions. ALE x O DIG External Memory Bus Address Latch Enable (ALE) signal. RJ1 0 O DIG LATJ data output. 1 I ST 0 O ANA SEG33 RJ2/SEG34/ WRL Each of the PORTJ pins has a weak internal pull-up. The pull-ups are provided to keep the inputs at a known state for the external memory interface while powering up. A single control bit can turn off all the pull-ups. This is performed by clearing bit, RJPU (PADCFG). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on any device Reset. Description LATJ data output. PORTJ data input. PORTJ data input. LCD Segment 33 output; disables all other pin functions. OE x O DIG External Memory Bus Address Latch Enable (OE) signal. RJ2 0 O DIG LATJ data output. 1 I ST PORTJ data input. SEG34 0 O ANA WRL x O DIG External Memory Bus Write Low (WRL) signal. RJ3 0 O DIG LATJ data output. LCD Segment 34 output; disables all other pin functions. 1 I ST SEG35 0 O ANA LCD Segment 35 output; disables all other pin functions. PORTJ data input. WRH x O DIG External Memory Bus Write High (WRH) signal. RJ4 0 O DIG LATJ data output. 1 I ST SEG39 0 O ANA LCD Segment 39 output; disables all other pin functions. BA0 x O DIG External Memory Bus Byte Access 0 (BA0) signal. RJ5 0 O DIG LATJ data output. 1 I ST SEG38 0 O ANA LCD Segment 38 output; disables all other pin functions. CE x O DIG External Memory Bus Chip Enable (CE) signal. PORTJ data input. PORTJ data input. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 218  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-9: PORTJ FUNCTIONS (CONTINUED) Pin Name Function TRIS Setting I/O I/O Type RJ6/SEG37/LB RJ6 0 O DIG 1 I ST 0 O ANA SEG37 RJ7/SEG36/UB Legend: Description LATJ data output. PORTJ data input. LCD Segment 37 output; disables all other pin functions. LB x O DIG External Memory Bus Lower Byte (LB) signal. RJ7 0 O DIG LATJ data output. 1 I ST SEG36 0 O ANA LCD Segment 36 output; disables all other pin functions. PORTJ data input. UB x O DIG External Memory Bus Upper Byte (UB) signal. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 219 PIC18F97J94 FAMILY 11.11 PORTK, LATK and TRISK Registers Note: PORTK is available only on 100-pin devices. PORTK is an 8-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are TRISK and LATK. All pins on PORTK are implemented with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. Each of the PORTK pins has a weak internal pull-up. The pull-ups are provided to keep the inputs at a known state for the external memory interface while powering up. A single control bit can turn off all the pull-ups. This is performed by clearing bit, RKPU (PADCFG). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on any device Reset. EXAMPLE 11-10: BANKSEL CLRF LATK LATK BANKSEL MOVLW TRISK 0CFh MOVWF TRISK ; ; ; ; ; ; ; ; ; ; ; INITIALIZING PORTK select bank with LATK register Initialize LATK by clearing output data latches Select bank with TRISK register Value used to initialize data direction Set RH3:RH0 as inputs RH5:RH4 as outputs RH7:RH6 as inputs TABLE 11-10: PORTK FUNCTIONS Pin Name RK0/SEG56 RK1/SEG57 RK2/SEG58 RK3/SEG59 RK4/SEG60 Function TRIS Setting I/O I/O Type RK0 0 O DIG 1 I ST SEG56 0 O ANA LCD Segment 56 output; disables all other pin functions. RK1 0 O DIG LATK data output. 1 I ST SEG57 0 O ANA LCD Segment 57 output; disables all other pin functions. RK2 0 O DIG LATK data output. RK6/SEG62 PORTK data input. I ST 0 O ANA LCD Segment 58 output; disables all other pin functions. RK3 0 O DIG LATK data output. 1 I ST PORTK data input. SEG59 0 O ANA LCD Segment 59 output; disables all other pin functions. RK4 0 O DIG LATK data output. 1 I ST 0 O ANA LCD Segment 60 output; disables all other pin functions. LATK data output. RK5 PORTK data input. PORTK data input. 0 O DIG 1 I ST SEG61 0 O ANA LCD Segment 61 output; disables all other pin functions. RK6 0 O DIG LATK data output. RK7 SEG63 Legend: PORTK data input. 1 SEG62 RK7/SEG63 LATK data output. SEG58 SEG60 RK5/SEG61 Description PORTK data input. 1 I ST 0 O ANA LCD Segment 62 output; disables all other pin functions. PORTK data input. 0 O DIG LATK data output. 1 I ST PORTK data input. 0 O ANA LCD Segment 63 output; disables all other pin functions. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option). DS30000575C-page 220  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 11.12 PORTL, LATL and TRISL Registers Note: The pull-ups are provided to keep the inputs at a known state for the external memory interface while powering up. A single control bit can turn off all the pull-ups. This is performed by clearing bit, RLPU (PADCFG). PORTL is available only on 100-pin devices. The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on any device Reset. PORTL is an 8-bit wide, bidirectional port. The corresponding Data Direction and Output Latch registers are TRISL and LATL. All pins on PORTL are implemented with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. EXAMPLE 11-11: BANKSEL PORTL CLRF PORTL Each of the PORTL pins has a weak internal pull-up. CLRF LATL MOVLW 0CFh MOVWF TRISL ; ; ; ; ; ; ; ; ; ; ; INITIALIZING PORTL select correct bank Initialize PORTL by clearing output latches Alternate method to clear output latches Value used to initialize data direction Set RL3:RL0 as inputs RL5:RL4 as output RL7:RL6 as inputs TABLE 11-11: PORTL FUNCTIONS Pin Name RL0/SEG48 RL1/SEG49 RL2/SEG50 RL3/SEG51 RL4/SEG52 RL5/SEG53 RL6/SEG54 RL7/SEG55 Function TRIS Setting I/O I/O Type RL0 0 O DIG LATL data output. 1 I ST SEG48 0 O ANA RL1 0 O DIG LATL data output. 1 I ST PORTL data input. SEG49 0 O ANA RL2 0 O DIG LATL data output. 1 I ST PORTL data input. SEG50 0 O ANA RL3 0 O DIG LATL data output. 1 I ST PORTL data input. SEG51 0 O ANA LCD Segment 51 output; disables all other pin functions. RL4 0 O DIG LATL data output. PORTL data input. LCD Segment 48 output; disables all other pin functions. LCD Segment 49 output; disables all other pin functions. LCD Segment 50 output; disables all other pin functions. 1 I ST SEG52 0 O ANA RL5 0 O DIG LATL data output. 1 I ST PORTL data input. SEG53 0 O ANA RL6 0 O DIG LATL data output. 1 I ST PORTL data input. SEG54 0 O ANA RL7 0 O DIG LATL data output. 1 I ST PORTL data input. 0 O ANA SEG55 Legend: Description PORTL data input. LCD Segment 52 output; disables all other pin functions. LCD Segment 53 output; disables all other pin functions. LCD Segment 54 output; disables all other pin functions. LCD Segment 55 output; disables all other pin functions. O = Output, I = Input, ANA = Analog Signal, DIG = Digital Output, ST = Schmitt Trigger Buffer Input, x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).  2012-2016 Microchip Technology Inc. DS30000575C-page 221 PIC18F97J94 FAMILY 11.13 Parallel Slave Port PORTD can function as an 8-bit-wide Parallel Slave Port (PSP), or microprocessor port, when control bit, PSPMODE (PSPCON), is set. The port is asynchronously readable and writable by the external world through the RD control input pin (RE0/AD8/LCDBIAS1/RP28/RD) and WR control input pin (RE1/AD9/ LCDBIAS2/RP29/WR). Note: The Parallel Slave Port is available only in Microcontroller mode. The PSP can directly interface to an 8-bit microprocessor data bus. The external microprocessor can read or write the PORTD latch as an 8-bit latch. Setting bit, PSPMODE, enables port pin, RE0/AD8/ LCDBIAS1/RP28/RD, to be the RD input, RE1/AD9/ LCDBIAS2/RP29/WR to be the WR input and RE2/ AD10/LCDBIAS3/RP30/CS to be the CS (Chip Select) input. For this functionality, the corresponding data direction bits of the TRISE register (TRISE) must be configured as inputs (‘111’). A write to the PSP occurs when both the CS and WR lines are first detected low and ends when either are detected high. The PSPIF and IBF flag bits (PIR1 and PSPCON, respectively) are set when the write ends. A read from the PSP occurs when both the CS and RD lines are first detected low. The data in PORTD is read out and the OBF bit (PSPCON) is set. If the user writes new data to PORTD to set OBF, the data is immediately read out, but the OBF bit is not set. When either the CS or RD line is detected high, the PORTD pins return to the input state and the PSPIF bit is set. User applications should wait for PSPIF to be set before servicing the PSP. When this happens, the IBF and OBF bits can be polled and the appropriate action taken. FIGURE 11-3: Data Bus WR LATD or PORTD PORTD AND PORTE BLOCK DIAGRAM (PARALLEL SLAVE PORT) D Q RDx Pin CK Data Latch Q RD PORTD TTL D ENEN TRIS Latch RD LATD One Bit of PORTD Set Interrupt Flag PSPIF (PIR1) Read TTL RD Chip Select TTL CS Write TTL WR Note: The I/O pin has protection diodes to VDD and VSS. The timing for the control signals in Write and Read modes is shown in Figure 11-4 and Figure 11-5, respectively. DS30000575C-page 222  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 11-4: PSPCON: PARALLEL SLAVE PORT CONTROL REGISTER R-0 R-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 IBF OBF IBOV PSPMODE — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 IBF: Input Buffer Full Status bit 1 = A word has been received and is waiting to be read by the CPU 0 = No word has been received bit 6 OBF: Output Buffer Full Status bit 1 = The output buffer still holds a previously written word 0 = The output buffer has been read bit 5 IBOV: Input Buffer Overflow Detect bit 1 = A write occurred when a previously input word had not been read (must be cleared in software) 0 = No overflow occurred bit 4 PSPMODE: Parallel Slave Port Mode Select bit 1 = Parallel Slave Port mode 0 = General Purpose I/O mode bit 3-0 Unimplemented: Read as ‘0’ FIGURE 11-4: PARALLEL SLAVE PORT WRITE WAVEFORMS Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 CS WR RD PORTD IBF OBF PSPIF  2012-2016 Microchip Technology Inc. DS30000575C-page 223 PIC18F97J94 FAMILY FIGURE 11-5: PARALLEL SLAVE PORT READ WAVEFORMS Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 CS WR RD PORTD IBF OBF PSPIF 11.14 Virtual PORT 11.15.1 This device includes a single virtual port, which is used to construct a logically addressed 8-bit PORT from 8 physically unrelated pins on the device. The virtual PORT is controlled through the PORTVP, LATVP and TRISVP registers. These function identically to the PORT, LAT and TRIS registers of the actual I/O ports. Refer to Section 11.1 “I/O Port Pin Capabilities” for more information. The PPS-Lite feature is used with a range of pins. All devices in the PIC18FXXJ94 family contain a total of 47 remappable peripheral pins, labeled RP0 through RP46. Pins that support PPS-Lite feature include the designation, “RPn” in their full pin designation, where “RP” designates a remappable peripheral and “n” is the remappable pin number. For PIC18FXXJ94 devices, RP41 through RP45 are digital inputs only. 11.15 PPS-Lite Previous PIC18 devices had I/O pins that were “hardwired” to a set of peripherals. For example, a port pin might have had the option of serving as an I/O pin, an analog input or as an interrupt source. In an effort to increase the flexibility of the parts, PIC18FXXJ94 devices contain PPS-Lite (Peripheral Pin Select-Lite), which allows the developer to connect an internal peripheral to a subset of pins. PPS-Lite is similar to PPS (available on PIC18F products), but limits the user to interconnections within four sets of pin/peripheral groups. The PPS-Lite feature allows some flexibility in choosing which peripheral connects to any particular pin. This allows designs to be maximized for layout efficiency, and also may allow component changes without changing the printed circuit board design. The Peripheral Pin Select feature operates over a fixed subset of digital I/O pins (those designated as RPn pins). Users may independently map the input and/or output of most digital peripherals to a limited set of these I/O pins. The PPS-Lite configuration is performed in software and does not require the device to be reprogrammed. Hardware safeguards are included that prevent accidental or spurious changes to the peripheral mapping once it has been established. DS30000575C-page 224 11.15.2 AVAILABLE PINS AVAILABLE PERIPHERALS The peripherals managed by the Peripheral Pin Select are all “digital only” peripherals. These include general serial communications (USART and SPI), general purpose timer clock inputs, timer related peripherals (input capture and output compare) and external interrupt inputs. In comparison, some digital only peripheral modules are not currently included in the Peripheral Pin Select feature. This is because the peripheral’s function requires special I/O circuitry on a specific port and cannot be easily connected to multiple pins. These modules include I2C, USB, change notification inputs, RTCC alarm output and all modules with analog inputs, such as the A/D Converter. A key difference between remappable and non-remappable peripherals is that remappable peripherals are not associated with a default I/O pin. The peripheral must always be assigned to a specific I/O pin before it can be used. In contrast, non-remappable peripherals are always available on a default pin, assuming that the peripheral is active and not conflicting with another peripheral. When a remappable peripheral is active on a given I/O pin, it takes priority over all other digital I/O and digital communication peripherals associated with the pin. Priority is given, regardless of the type of peripheral that is mapped. Remappable peripherals never take priority over any analog functions associated with the pin.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 11-6: STRUCTURE OF PORT SHARED WITH PPS PERIPHERALS Open-Drain Selection Output Multiplexers Peripheral Pin Select Output Function Select for the Pin Peripheral ‘n’ Output Enable Peripheral 2 Output Enable Peripheral 1 Output Enable I/O TRIS Enable n 1 0 I/O 0 1 Peripheral ‘n’ Output Data Peripheral 2 Output Data Peripheral 1 Output Data I/O LAT/PORT Data PIO Module Read TRIS Data Bus WR TRIS D Q CK Q n 1 0 I/O Pin TRIS Latch WR LAT/ WR PORT D Q CK Data Latch Read LAT Read PORT Peripheral Input Pin Selection 0 Peripheral Input 1 n  2012-2016 Microchip Technology Inc. I/O Pin 0 I/O Pin 1 I/O Pin n DS30000575C-page 225 PIC18F97J94 FAMILY 11.15.3 CONTROLLING PERIPHERAL PIN SELECT fields, with each set associated with one of the remappable peripherals. Programming a given peripheral’s bit field with an RPn value maps the RPn pin to that peripheral. For any given device, the valid range of values for any of the bit fields corresponds to the maximum number of peripheral Pin Selections supported by the device. Peripheral Pin Select features are controlled through two sets of Special Function Registers (SFRs): one to map peripheral inputs and one to map peripheral outputs. Because they are separately controlled, a particular peripheral’s input and output (if the peripheral has both) can be placed on any selectable function with the only constraint being that RPn peripherals and pins can only be mapped within their own group. It is not possible to map a peripheral to a pin outside of its group or vice versa. The PPS-Lite peripheral inputs and associated RPn pins have been organized into four groups. It is not possible to map a peripheral to an RPn pin which is outside of its group. To map a peripheral input signal to an RPn pin, use the 4-step process as indicated in Table 11-13. Choose the signal and the RPn pin, and the column on the right shows which value to write to the associated RPIN register. The association of a peripheral to a peripheral-selectable pin is handled in two different ways, depending if an input or output is being mapped. 11.15.3.1 The peripheral inputs that support Peripheral Pin Selection have no default pins. Since the implemented bit fields of RPINRx registers reset to all ‘1’s, the inputs are all tied to VSS in the device’s default (Reset) state. Input Mapping The inputs of the Peripheral Pin Select options are mapped on the basis of the peripheral; that is, a bit field associated with a peripheral dictates the pin it will be mapped to. The RPINRx registers (refer to registers in Table 11-12 and Table 11-13) contain sets of 4-bit FIGURE 11-7: For example, to assign U1RX to RP3, write the value, h’0, to RPINR0_1. Figure 11-7 illustrates remappable pin selection for the U1RX input. REMAPPABLE INPUT FOR U1RX RPINR0_1 0 RP3 1 RP7 2 U1RX Input to Peripheral RP11 A RP(4n+3) DS30000575C-page 226  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-12: RPINR REGISTERS Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RPINR52_53 RVP7R3 RVP7R2 RVP7R1 RVP7R0 RVP6R3 RVP6R2 RVP6R1 RVP6R0 RPINR50_51 RVP5R3 RVP5R2 RVP5R1 RVP5R0 RVP4R3 RVP4R2 RVP4R1 RVP4R0 RPINR48_49 RVP3R3 RVP3R2 RVP3R1 RVP3R0 RVP2R3 RVP2R2 RVP2R1 RVP2R0 RPINR46_47 RVP1R3 RVP1R2 RVP1R1 RVP1R0 RVP0R3 RVP0R2 RVP0R1 RVP0R0 RPINR44_45 T5CKIR3 T5CKIR2 T5CKIR1 T5CKIR0 T5GR3 T5GR2 T5GR1 T5GR0 RPINR42_43 T3CKIR3 T3CKIR2 T3CKIR1 T3CKIR0 T3GR3 T3GR2 T3GR1 T3GR0 RPINR40_41 T1CKIR3 T1CKIR2 T1CKIR1 T1CKIR0 T1GR3 T1GR2 T1GR1 T1GR0 RPINR38_39 T0CKIR3 T0CKIR2 T0CKIR1 T0CKIR0 CCP10R3 CCP10R2 CCP10R1 CCP10R0 RPINR36_37 CCP9R3 CCP9R2 CCP9R1 CCP9R0 CCP8R3 CCP8R2 CCP8R1 CCP8R0 RPINR34_35 CCP7R3 CCP7R2 CCP7R1 CCP7R0 CCP6R3 CCP6R2 CCP6R1 CCP6R0 RPINR32_33 CCP5R3 CCP5R2 CCP5R1 CCP5R0 CCP4R3 CCP4R2 CCP4R1 CCP4R0 RPINR30_31 MDCIN2R3 MDCIN2R2 MDCIN2R1 MDCIN2R0 RPINR28_29 MDMINR3 MDMINR2 MDMINR1 MDMINR0 INT3R3 INT3R2 INT3R1 RPINR26_27 INT2R3 INT2R2 INT2R1 INT2R0 INT1R3 INT1R2 INT1R1 INT1R0 RPINR24_25 IOC7R3 IOC7R2 IOC7R1 IOC7R0 IOC6R3 IOC6R2 IOC6R1 IOC6R0 RPINR22_23 IOC5R3 IOC5R2 IOC5R1 IOC5R0 IOC4R3 IOC4R2 IOC4R1 IOC4R0 RPINR20_21 IOC3R3 IOC3R2 IOC3R1 IOC3R0 IOC2R3 IOC2R2 IOC2R1 IOC2R0 RPINR18_19 IOC1R3 IOC1R2 IOC1R1 IOC1R0 IOC0R3 IOC0R2 IOC0R1 IOC0R0 RPINR16_17 ECCP3R3 ECCP3R2 ECCP3R1 ECCP3R0 ECCP2R3 ECCP2R2 ECCP2R1 ECCP2R0 RPINR14_15 ECCP1R3 ECCP1R2 ECCP1R1 ECCP1R0 FLT0R3 FLT0R2 FLT0R1 FLT0R0 SDI2R0 MDCIN1R3 MDCIN1R2 MDCIN1R1 MDCIN1R0 INT3R0 RPINR12_13 SS2R3 SS2R2 SS2R1 SS2R0 SDI2R3 SDI2R2 SDI2R1 RPINR10_11 SCK2R3 SCK2R2 SCK2R1 SCK2R0 SS1R3 SS1R2 SS1R1 SS1R0 RPINR8_9 SDI1R3 SDI1R2 SDI1R1 SDI1R0 SCK1R3 SCK1R2 SCK1R1 SCK1R0 RPINR6_7 U4TXR3 U4TXR2 U4TXR1 U4TXR0 U4RXR3 U4RXR2 U4RXR1 U4RXR0 RPINR4_5 U3TXR3 U3TXR2 U3TXR1 U3TXR0 U3RXR3 U3RXR2 U3RXR1 U3RXR0 RPINR2_3 U2TXR3 U2TXR2 U2TXR1 U2TXR0 U2RXR3 U2RXR2 U2RXR1 U2RXR0 RPINR0_1 U1TXR3 U1TXR2 U1TXR1 U1TXR0 U1RXR3 U1RXR2 U1RXR1 U1RXR0  2012-2016 Microchip Technology Inc. DS30000575C-page 227 PIC18F97J94 FAMILY TABLE 11-13: RPIN REGISTERS AND AVAILABLE FUNCTIONS PPS-Lite Input Peripheral Group 4n (1) To Map this signal (4) to the Associated RPIN Register SDI1 RPINR8_9 PPS-Lite Input Peripheral Group 4n + 1 (1) To Map this Signal (4) to the Associated RPIN Register SDI2 RPINR12_13 FLT0 RPINR14_15 INT1 RPINR26_27 IOC0 RPINR18_19 IOC1 RPINR18_19 IOC4 RPINR22_23 IOC5 RPINR22_23 MDCIN1 RPINR30_31 MDCIN2 RPINR30_31 T0CKI RPINR38_39 T1CKI RPINR40_41 T5G RPINR44_45 T1G RPINR40_41 U3RX RPINR4_5 T3CKI RPINR42_43 U4RX RPINR6_7 T3G RPINR42_43 CCP5 RPINR32_33 T5CKI RPINR44_45 CCP8 RPINR36_37 U3TX RPINR4_5 RVP0 RPINR46_47 U4TX RPINR6_7 RVP4 RPINR50_51 CCP7 RPINR34_35 CCP9 RPINR36_37 RVP1 RPINR46_47 RVP5 RPINR50_51 (2) with this RPn Pin (3) Write this Corresponding Value (2) with this RPn Pin (3) Write this Corresponding Value RP0 h’0 RP1 h’0 RP4 h’1 RP5 h’1 RP8 h’2 RP9 h’2 RP12 h’3 RP13 h’3 RP16 h’4 RP17 h’4 RP20 h’5 RP21 h’5 RP24 h’6 RP25 h’6 RP28 h’7 RP29 h’7 RP32 h’8 RP33 h’8 RP36 h’9 RP37 h’9 RP40 h’A RP41 h’A RP44 h’B RP45 h’B — h’C — h’C — h’D — h’D — h’E — h’E VSS h’F VSS h’F DS30000575C-page 228  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-13: RPIN REGISTERS AND AVAILABLE FUNCTIONS (CONTINUED) PPS-Lite Input Peripheral Group 4n + 2 (1) To Map this Signal (4) to the Associated RPIN Register RPINR10_11 SS1 PPS-Lite Input Peripheral Group 4n + 3 (1) To Map this Signal (4) to the Associated RPIN Register SS2 RPINR12_13 INT2 RPINR26_27 INT3 RPINR28_29 IOC2 RPINR20_21 IOC3 RPINR20_21 IOC6 RPINR24_25 IOC7 RPINR24_25 MDMIN RPINR28_29 U1RX RPINR0_1 RPINR2_3 U1TX RPINR0_1 U2TX U2RX RPINR2_3 SCK1 RPINR8_9 SCK2 RPINR10_11 ECCP1 RPINR14_15 ECCP3 RPINR16_17 ECCP2 RPINR16_17 CCP6 RPINR34_35 CCP4 RPINR32_33 CCP10 RPINR38_39 RVP3 RPINR48_49 RVP2 RPINR48_49 RVP7 RPINR52_53 RVP6 RPINR52_53 (2) with this RPn Pin (3) Write this Corresponding Value (2) with this RPn Pin (3) Write this Corresponding Value RP2 h’0 RP3 h’0 RP6 h’1 RP7 h’1 RP10 h’2 RP11 h’2 RP14 h’3 RP15 h’3 RP18 h’4 RP19 h’4 RP22 h’5 RP23 h’5 RP26 h’6 RP27 h’6 RP30 h’7 RP31 h’7 RP34 h’8 RP35 h’8 RP38 h’9 RP39 h’9 RP42 h’A RP43 h’A RP46 h’B — h’B — h’C — h’C — h’D — h’D — h’E — h’E VSS h’F VSS h’F 11.15.3.2 Output Mapping In contrast to the inputs, the outputs of the Peripheral Pin Select options are mapped on the basis of the pin. In this case, a bit field associated with a particular pin dictates the peripheral output to be mapped. The RPORx registers contain sets of 4-bit fields, with each associated with one RPn pin (see Register 11-5). The value of the bit field corresponds to one of the peripherals and that peripheral’s output is mapped to the pin. Each pin has a limited set of peripherals to choose from. The PPS-Lite peripheral outputs and associated RPn pins have been organized into four groups. It is not possible to map a peripheral to an RPn pin which is outside of its group. To map a peripheral output signal to  2012-2016 Microchip Technology Inc. an RPn pin, use the 4-step process, as indicated in Table 11-14. Choose the RPn pin and the signal; the column on the right shows which value to write to the associated RPORx register. The peripheral outputs that support Peripheral Pin Selection have no default pins. Since the RPORx registers reset to all ‘0’s, the outputs are all disconnected in the device’s default (Reset) state. The list of peripherals for output mapping also includes a null value of b’0000’ because of the mapping technique. This allows unused peripherals to not be connected to a pin. Not all peripherals are available on all pins. For example, the “SDO2” signal is only available on RP0, RP4, RP8, etc. The “SDO2” signal is not available on RP1. DS30000575C-page 229 PIC18F97J94 FAMILY FIGURE 11-8: MULTIPLEXING OF REMAPPABLE OUTPUT FOR RPn RPORn I/O TRIS Setting 0 U1TX Output Enable 3 U1RTS Output Enable 4 Output Enable OC5 Output Enable I/O LAT/PORT Content 22 0 U1TX Output 3 U1RTS Output 4 RPn Output Data OC5 Output REGISTER 11-5: 22 RPORn_n: REMAPPED PERIPHERAL OUTPUT REGISTER n (FUNCTION MAPS TO PIN) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RPORn_3 RPORn_2 RPORn_1 RPORn_0 RPmR_3 RPmR_2 RPmR_1 RPmR_0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-4 RPORn_: RPn peripheral output function mapping bit 3-0 RPmR: RPm peripheral output function mapping Note 1: x = Bit is unknown Register values can only be changed if IOLOCK = 0. DS30000575C-page 230  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 11-14: PPS-LITE OUTPUT PPS-Lite Output Peripheral Group 4n PPS-Lite Output Peripheral Group 4n + 1 (1) To Map this RPn Pin (4) to the Associated RPOR Register (1) To Map this RPn Pin (4) to the Associated RPOR Register RP0 RPOR0_1 RP1 RPOR0_1 RP4 RPOR4_5 RP5 RPOR4_5 RP8 RPOR8_9 RP9 RPOR8_9 RP12 RPOR12_13 RP13 RPOR12_13 RP16 RPOR16_17 RP17 RPOR16_17 RP20 RPOR20_21 RP21 RPOR20_21 RP24 RPOR24_25 RP25 RPOR24_25 RP28 RPOR28_29 RP29 RPOR28_29 RP32 RPOR32_33 RP33 RPOR32_33 RP36 RPOR36_37 RP37 RPOR36_37 RP40 RPOR40_41 RP41 RPOR40_41 RP44 RPOR44_45 RP45 RPOR44_45 (2) with this Output Signal (3) Write this Corresponding Value (2) with this Output Signal (3) Write this Corresponding Value Disabled h’0 Disabled h’0 U2BCLK h’1 U1BCLK h’1 U3RX_DT h’2 U3TX_CK h’2 U4RX_DT h’3 U4TX_CK h’3 SDO2 h’4 SDO1 h’4 P1D h’5 P1C h’5 P2D h’6 P2C h’6 P3B h’7 P3C h’7 CTPLS h’8 CCP7 h’8 CCP5 h’9 CCP9 h’9 CCP8 h’A C2OUT h’A C1OUT h’B Unused h’B Unused h’C Unused h’C RVP0 h’D RVP1 h’D RVP4 h’E RVP5 h’E Reserved h’F Reserved h’F  2012-2016 Microchip Technology Inc. DS30000575C-page 231 PIC18F97J94 FAMILY TABLE 11-14: PPS-LITE OUTPUT (CONTINUED) PPS-Lite Output Peripheral Group 4n + 2 PPS-Lite Output Peripheral Group 4n +3 (1) To Map this RPn Pin (4) to the Associated RPOR Register (1) To Map this RPn Pin (4) to the Associated RPOR Register RP2 RPOR2_3 RP3 RPOR2_3 RP6 RPOR6_7 RP7 RPOR6_7 RP10 RPOR10_11 RP11 RPOR10_11 RP14 RPOR14_15 RP15 RPOR14_15 RP18 RPOR18_19 RP19 RPOR18_19 RP22 RPOR22_23 RP23 RPOR22_23 RP26 RPOR26_27 RP27 RPOR26_27 RP30 RPOR30_31 RP31 RPOR30_31 RP34 RPOR34_35 RP35 RPOR34_35 RP38 RPOR38_39 RP39 RPOR38_39 RP42 RPOR42_43 RP43 RPOR42_43 RP46 RPOR46 (2) with this Output Signal (3) Write this Corresponding Value (2) with this Output Signal (3) Write this Corresponding Value Disabled h’0 Disabled h’0 U1TX_CK h’1 U1RX_DT h’1 U2RX_DT h’2 U2TX_CK h’2 U3BCLK h’3 SCK1 h’3 U4BCLK h’4 ECCP1/P1A h’4 SCK2 h’5 ECCP2/P2A h’5 P1B h’6 P3D h’6 h’7 P2B h’7 MDOUT ECCP3/P3A h’8 CCP4 h’8 CCP6 h’9 C3OUT h’9 CCP10 h’A Unused h’A Unused h’B Unused h’B Unused h’C Unused h’C RVP2 h’D RVP3 h’D RVP6 h’E RVP7 h’E Reserved h’F Reserved h’F 11.15.3.3 I/O Mapping While most peripheral signals are defined as either input or output, some peripheral signals switch between input and output: UnRX_DT, UnTX_CK, PBIO and CCP. Most commonly, these signals are mapped so that both the input and output map to the same RPn pin. If desired, the input and output can be mapped to separate pins. For standard peripheral operation, ensure that both the input and output mapping configurations select the same RPn pin. 11.15.3.4 Mapping Limitations The control schema of Peripheral Select Pins is not limited to a small range of fixed peripheral configurations. There are no mutual or hardware enforced lockouts between any of the peripheral mapping SFRs. While such mappings may be technically possible from a DS30000575C-page 232 configuration point of view, the user must ensure the selected configurations are supportable from an electrical point of view. 11.15.4 CONTROLLING CONFIGURATION CHANGES Because peripheral remapping can be changed during run time, some restrictions on peripheral remapping are needed to prevent accidental configuration changes. PIC18FXXJ94 devices include two features to prevent alterations to the peripheral map: • Continuous state monitoring • Configuration bit remapping lock  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 11.15.4.1 Control Register Lock The contents of RPINRx and RPORx registers are constantly monitored in hardware by shadow registers. If an unexpected change in any of the registers occurs (such as cell disturbances caused by ESD or other external events), a Configuration Mismatch Reset will trigger. 11.15.4.2 Configuration Bit Pin Select Lock As an additional level of safety, the device can be configured to prevent more than one write session to the RPINRx and RPORx registers. The IOL1WAY Configuration bit (CONFIG5H) blocks the IOLOCK bit from being cleared after it has been set once. In the default (unprogrammed) state, IOL1WAY is set, restricting users to one write session. Programming IOL1WAY allows users unlimited access to the Peripheral Pin Select registers. It is good programming practice to always set the IOLOCK bit (OSCCON2) after all changes have been made to PPS-Lite registers. 11.15.5 CONSIDERATIONS FOR PERIPHERAL PIN SELECTION The ability to control Peripheral Pin Selection introduces several considerations into application design that should be considered. This is particularly true for several common peripherals which are only available as remappable peripherals. The assignment of an RPn pin to the peripheral input or output depends on the peripheral and its use in the application. It is good programming practice to map peripherals to pins immediately after Reset. This should be done before any configuration changes to the peripheral itself. The assignment of a peripheral output to a particular pin does not automatically perform any other configuration of the pin’s I/O circuitry. This means adding a pinselectable output to a pin may mean inadvertently driving an existing peripheral input when the output is driven. Users must be familiar with the behavior of other fixed peripherals that share a remappable pin. To be safe, fixed digital peripherals that share the same pin should be disabled when not in use. Configuring a remappable pin for a specific peripheral input does not automatically turn that feature on. The peripheral must be specifically configured for operation and enabled, as if it were tied to a fixed pin. A final consideration is that Peripheral Pin Select functions neither override analog inputs, nor reconfigure pins with analog functions for digital I/O. If a pin is configured as an analog input on device Reset, it must be explicitly reconfigured as digital I/O when used with a Peripheral Pin Select. 11.15.5.1 Before any other application code is executed, the user must initialize the device with the proper peripheral configuration. Since the IOLOCK is not active in the Reset state, the peripherals can be configured, and the IOLOCK bit can be set when configuration is complete. 1. Choosing the configuration requires the review of all Peripheral Pin Selects and their pin assignments, especially those that will not be used in the application. In all cases, unused pin-selected peripherals should be disabled. Unused peripherals should have their inputs assigned to VSS. I/O pins with unused RPn functions should be configured with the NULL (‘0’) peripheral output. 3.  2012-2016 Microchip Technology Inc. 2. 4. 5. 6. Basic Steps to Use Peripheral Pin Selection Lite (PPS-Lite) Disable any fixed digital peripherals on the pins to be used. Switch pins to be used for digital functionality (if they have analog functionality) using the ANCONx registers. Clear the IOLOCK bit (OSCCON) if needed (not needed after a device Reset). Set RPINRx and RPORx registers appropriately. Set the IOLOCK bit (OSCCON). Enable and configure newly mapped PPS-Lite peripherals. DS30000575C-page 233 PIC18F97J94 FAMILY 12.0 DATA SIGNAL MODULATOR The Data Signal Modulator (DSM) is a peripheral which allows the user to mix a data stream, also known as a modulator signal, with a carrier signal to produce a modulated output. Both the carrier and the modulator signals are supplied to the DSM module, either internally from the output of a peripheral, or externally through an input pin. The carrier signal is comprised of two distinct and separate signals: a Carrier High (CARH) signal and a Carrier Low (CARL) signal. During the time in which the Modulator (MOD) signal is in a logic high state, the DSM mixes the Carrier High signal with the Modulator signal. When the Modulator signal is in a logic low state, the DSM mixes the Carrier Low signal with the Modulator signal. DS30000575C-page 234 Using this method, the DSM can generate the following types of key modulation schemes: • Frequency-Shift Keying (FSK) • Phase-Shift Keying (PSK) • On-Off Keying (OOK) Additionally, the following features are provided within the DSM module: • • • • • • • Carrier Synchronization Carrier Source Polarity Select Carrier Source Pin Disable Programmable Modulator Data Modulator Source Pin Disable Modulator Output Polarity Select Slew Rate Control Figure 12-1 shows a simplified block diagram of the Data Signal Modulator peripheral.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 12-1: SIMPLIFIED BLOCK DIAGRAM OF THE DATA SIGNAL MODULATOR MDCH VSS MDCIN1 MDCIN2 REFO1 Clock ECCP1 ECCP2 ECCP3 CCP4 CCP5 CCP6 CCP7 CCP8 CCP9 CCP10 System Clock REFO2 Clock 0000 0001 0010 0011 0100 0101 0110 CARH 0111 1000 1001 1010 1011 1100 1101 1110 1111 MDEN EN Data Signal Modulator MDCHPOL D SYNC Q 1 MDSRC MDBIT MDMIN MSSP1 (SDO) MSSP2 (SDO) EUSART1 (TXX) EUSART2 (TXX) EUSART3 (TXX) EUSART4 (TXX) ECCP1 ECCP2 ECCP3 CCP4 CCP5 CCP6 CCP7 CCP8 0000 0001 0010 0011 0100 0101 0110 MOD 0111 1000 1001 1010 1011 1100 1101 1110 1111 0 MDCHSYNC MDOUT MDOPOL D SYNC MDCL VSS MDCIN1 MDCIN2 REFO1 Clock ECCP1 ECCP2 ECCP3 CCP4 CCP5 CCP6 CCP7 CCP8 CCP9 CCP10 System Clock REFO2 CLOCK MDOE Switches Between PORT Function and DSM Output Q 0000 0001 0010 0011 0100 0101 0110 CARL 0111 1000 1001 1010 1011 1100 1101 1110 1111  2012-2016 Microchip Technology Inc. 1 0 MDCLSYNC MDCLPOL DS30000575C-page 235 PIC18F97J94 FAMILY 12.1 DSM Operation The DSM module can be enabled by setting the MDEN bit in the MDCON register. Clearing the MDEN bit in the MDCON register disables the DSM module by automatically switching the Carrier High and Carrier Low signals to the VSS signal source. The Modulator signal source is also switched to the MDBIT in the MDCON register. This not only assures that the DSM module is inactive, but that it is also consuming the least amount of current. 12.3 Carrier Signal Sources The Carrier High signal and Carrier Low signal can be supplied from the following sources: The Modulation Carrier High and Modulation Carrier Low Control registers are not affected when the MDEN bit is cleared, and the DSM module is disabled. The values inside these registers remain unchanged while the DSM is inactive. The sources for the Carrier High, Carrier Low and Modulator signals will once again be selected when the MDEN bit is set, and the DSM module is again enabled and active. • • • • • • • • • • • • • The modulated output signal can be disabled without shutting down the DSM module. The DSM module will remain active and continue to mix signals, but the output value will not be sent to the MDOUT pin. During the time that the output is disabled, the MDOUT pin will remain low. The modulated output can be disabled by clearing the MDOE bit in the MDCON register. The Carrier High signal is selected by configuring the MDCH bits in the MDCARH register. The Carrier Low signal is selected by configuring the MDCL bits in the MDCARL register. 12.2 Modulator Signal Sources The Modulator signal can be supplied from the following sources: • • • • • • • • • • • • • • • • • • ECCP1 Signal ECCP2 Signal ECCP3 Signal CCP2 Signal CCP3 Signal CCP4 Signal CCP5 Signal CCP6 Signal CCP7 Signal CCP8 Signal MSSP1 SDO Signal (SPI mode only) MSSP2 SDO Signal (SPI mode only) EUSART1 TX1 Signal EUSART2 TX2 Signal EUSART3 TX3 Signal EUSART4 TX4 Signal External Signal on MDMIN Pin (RF0/MDMIN) MDBIT bit in the MDCON Register ECCP1 Signal ECCP2 Signal ECCP3 Signal CCP5 Signal CCP6 Signal CCP7 Signal CCP8 Signal CCP9 Signal CCP10 Signal Reference Clock Output Module Signal (REFO1) Reference Clock Output Module Signal (REFO2) System Clock External Signals on the MDCIN1 and MDCIN2 pins are available though PPS. Refer to Section 11.15 “PPS-Lite” for setup. • VSS 12.4 Carrier Synchronization During the time when the DSM switches between Carrier High and Carrier Low signal sources, the carrier data in the modulated output signal can become truncated. To prevent this, the carrier signal can be synchronized to the Modulator signal. When synchronization is enabled, the carrier pulse that is being mixed at the time of the transition is allowed to transition low before the DSM switches over to the next carrier source. Synchronization is enabled separately for the Carrier High and Carrier Low signal sources. Synchronization for the Carrier High signal can be enabled by setting the MDCHSYNC bit in the MDCARH register. Synchronization for the Carrier Low signal can be enabled by setting the MDCLSYNC bit in the MDCARL register. Figure 12-1 through Figure 12-6 show timing diagrams using various synchronization methods. The Modulator signal is selected by configuring the MDSRC bits in the MDSRC register. DS30000575C-page 236  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 12-2: ON-OFF KEYING (OOK) SYNCHRONIZATION Carrier Low (CARL) Carrier High (CARH) Modulator (MOD) MDCHSYNC = 1 MDCLSYNC = 0 MDCHSYNC = 1 MDCLSYNC = 1 MDCHSYNC = 0 MDCLSYNC = 0 MDCHSYNC = 0 MDCLSYNC = 1 FIGURE 12-3: NO SYNCHRONIZATION (MDCHSYNC = 0, MDCLSYNC = 0) Carrier High (CARH) Carrier Low (CARL) Modulator (MOD) MDCHSYNC = 0 MDCLSYNC = 0 Active Carrier State FIGURE 12-4: CARH CARL CARL CARH CARRIER HIGH SYNCHRONIZATION (MDCHSYNC = 1, MDCLSYNC = 0) Carrier High (CARH) Carrier Low (CARL) Modulator (MOD) MDCHSYNC = 1 MDCLSYNC = 0 Active Carrier State CARH  2012-2016 Microchip Technology Inc. both CARL CARH both CARL DS30000575C-page 237 PIC18F97J94 FAMILY FIGURE 12-5: CARRIER LOW SYNCHRONIZATION (MDCHSYNC = 0, MDCLSYNC = 1) Carrier High (CARH) Carrier Low (CARL) Modulator (MOD) MDCHSYNC = 0 MDCLSYNC = 1 Active Carrier State FIGURE 12-6: CARH CARL CARH CARL FULL SYNCHRONIZATION (MDCHSYNC = 1, MDCLSYNC = 1) Carrier High (CARH) Carrier Low (CARL) Modulator (MOD) Falling edges used to sync MDCHSYNC = 1 MDCLSYNC = 1 Active Carrier State DS30000575C-page 238 CARH CARL CARH CARL  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 12.5 Carrier Source Polarity Select The signal provided from any selected input source for the Carrier High and Carrier Low signals can be inverted. Inverting the signal for the Carrier High source is enabled by setting the MDCHPOL bit of the MDCARH register. Inverting the signal for the Carrier Low source is enabled by setting the MDCLPOL bit of the MDCARL register. 12.6 Carrier Source Pin Disable Some peripherals assert control over their corresponding output pin when they are enabled. For example, when the CCP1 module is enabled, the output of CCP1 is connected to the CCP1 pin. This default connection to a pin can be disabled by setting the MDCHODIS bit in the MDCARH register for the Carrier High source and the MDCLODIS bit in the MDCARL register for the Carrier Low source. 12.7 Programmable Modulator Data The MDBIT of the MDCON register can be selected as the source for the Modulator signal. This gives the user the ability to program the value used for modulation. 12.8 Modulator Source Pin Disable The Modulator source default connection to a pin can be disabled by setting the MDSODIS bit in the MDSRC register. 12.9 Modulated Output Polarity The modulated output signal provided on the MDOUT pin can also be inverted. Inverting the modulated output signal is enabled by setting the MDOPOL bit of the MDCON register. 12.10 Slew Rate Control When modulated data streams of 20 MHz or greater are required, the slew rate limitation on the output port pin can be disabled. The slew rate limitation can be removed by clearing the MDSLR bit in the MDCON register. 12.11 Operation In Sleep Mode The DSM module is not affected by Sleep mode. The DSM can still operate during Sleep if the carrier and Modulator input sources are also still operable during Sleep. 12.12 Effects of a Reset Upon any device Reset, the Modulator data signal module is disabled. The user’s firmware is responsible for initializing the module before enabling the output. The registers are reset to their default values.  2012-2016 Microchip Technology Inc. DS30000575C-page 239 PIC18F97J94 FAMILY REGISTER 12-1: R/W-0 MDCON: MODULATION CONTROL REGISTER R/W-0 MDEN MDOE R/W-1 MDSLR R/W-0 MDOPOL R/W-0 MDOUT (2) U-0 U-0 R/W-0 — — MDBIT(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 MDEN: Modulator Module Enable bit 1 = Modulator module is enabled and mixing input signals 0 = Modulator module is disabled and has no output bit 6 MDOE: Modulator Module Pin Output Enable bit 1 = Modulator pin output is enabled 0 = Modulator pin output is disabled bit 5 MDSLR: MDOUT Pin Slew Rate Limiting bit 1 = MDOUT pin slew rate limiting is enabled 0 = MDOUT pin slew rate limiting is disabled bit 4 MDOPOL: Modulator Output Polarity Select bit 1 = Modulator output signal is inverted 0 = Modulator output signal is not inverted bit 3 MDOUT: Modulator Output bit(2) Displays the current output value of the Modulator module. bit 2-1 Unimplemented: Read as ‘0’ bit 0 MDBIT: Modulator Source Input bit(1) Allows software to manually set modulation source input to the module. Note 1: 2: The MDBIT must be selected as the modulation source in the MDCON register for this operation. The modulated output frequency can be greater and asynchronous from the clock that updates this register bit. The bit value may not be valid for higher speed Modulator or carrier signals. DS30000575C-page 240  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 12-2: MDSRC: MODULATION SOURCE CONTROL REGISTER R/W-x U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x MDSODIS — — — MDSRC3 MDSRC2 MDSRC1 MDSRC0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 MDSODIS: Modulation Source Output Disable bit 1 = Output signal driving the peripheral output pin (selected by MDMS) is disabled 0 = Output signal driving the peripheral output pin (selected by MDMS) is enabled bit 6-4 Unimplemented: Read as ‘0’ bit 3-0 MDSRC Modulation Source Selection bits 1111 = CCP8 output (PWM Output mode only) 1110 = CCP7 output (PWM Output mode only) 1101 = CCP6 output (PWM Output mode only) 1100 = CCP5 output (PWM Output mode only) 1011 = CCP4 output (PWM Output mode only) 1010 = ECCP3 output (PWM Output mode only) 1001 = ECCP2 output (PWM Output mode only) 1000 = ECCP1 output (PWM Output mode only) 0111 = EUSART4 TXx output 0110 = EUSART3 TXx output 0101 = EUSART2 TXx output 0100 = EUSART1 TXx output 0011 = MSSP2 SDO signal (SPI mode only) 0010 = MSSP1 SDO signal (SPI mode only) 0001 = MDMIN pin 0000 = MDBIT bit of MDCON register is the modulation source  2012-2016 Microchip Technology Inc. DS30000575C-page 241 PIC18F97J94 FAMILY REGISTER 12-3: R/W-x MDCARH: MODULATION CARRIER HIGH CONTROL REGISTER R/W-x MDCHODIS MDCHPOL R/W-x U-0 R/W-x R/W-x R/W-x R/W-x MDCHSYNC — MDCH3(1) MDCH2(1) MDCH1(1) MDCH0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 MDCHODIS: Modulator Carrier High Output Disable bit 1 = Output signal driving the peripheral output pin (selected by MDCH) is disabled 0 = Output signal driving the peripheral output pin (selected by MDCH) is enabled bit 6 MDCHPOL: Modulator Carrier High Polarity Select bit 1 = Selected Carrier High signal is inverted 0 = Selected Carrier High signal is not inverted bit 5 MDCHSYNC: Modulator Carrier High Synchronization Enable bit 1 = Modulator waits for a falling edge on the Carrier High time signal before allowing a switch to the Carrier Low time 0 = Modulator output is not synchronized to the Carrier High time signal(1) bit 4 Unimplemented: Read as ‘0’ bit 3-0 MDCH: Modulator Data Carrier High Selection bits(1) 1111 = Reference Clock Output Module 2 (REFO2) signal 1110 = System clock 1101 = CCP10 output (PWM Output mode only) 1100 = CCP9 output (PWM Output mode only) 1011 = CCP8 output (PWM Output mode only) 1010 = CCP7 output (PWM Output mode only) 1001 = CCP6 output (PWM Output mode only) 1000 = CCP5 output (PWM Output mode only) 0111 = CCP4 output (PWM Output mode only) 0110 = ECCP3 output (PWM Output mode only) 0101 = ECCP2 output (PWM Output mode only) 0100 = ECCP1 output (PWM Output mode only) 0011 = Reference Clock Output Module 1 (REFO1) signal 0010 = MDCIN2 pin 0001 = MDCIN1 pin 0000 = No carrier input (tied to ground) Note 1: Narrowed carrier pulse widths or spurs may occur in the signal stream during transitions. DS30000575C-page 242  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 12-4: R/W-x MDCARL: MODULATION CARRIER LOW CONTROL REGISTER R/W-x MDCLODIS MDCLPOL R/W-x U-0 R/W-x R/W-x R/W-x R/W-x MDCLSYNC — MDCL3(1) MDCL2(1) MDCL1(1) MDCL0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 MDCLODIS: Modulator Carrier Low Output Disable bit 1 = Output signal driving the peripheral output pin (selected by MDCL) is disabled 0 = Output signal driving the peripheral output pin (selected by MDCL) is enabled bit 6 MDCLPOL: Modulator Carrier Low Polarity Select bit 1 = Selected Carrier Low signal is inverted 0 = Selected Carrier Low signal is not inverted bit 5 MDCLSYNC: Modulator Carrier Low Synchronization Enable bit 1 = Modulator waits for a falling edge on the Carrier Low time signal before allowing a switch to the Carrier High time 0 = Modulator output is not synchronized to the Carrier Low time signal(1) bit 4 Unimplemented: Read as ‘0’ bit 3-0 MDCL: Modulator Data Carrier Low Selection bits(1) 1111 = Reference Clock Output Module 2 (REFO2) signal 1110 = System clock 1101 = CCP10 output (PWM Output mode only) 1100 = CCP9 output (PWM Output mode only) 1011 = CCP8 output (PWM Output mode only) 1010 = CCP7 output (PWM Output mode only) 1001 = CCP6 output (PWM Output mode only) 1000 = CCP5 output (PWM Output mode only) 0111 = CCP4 output (PWM Output mode only) 0110 = ECCP3 output (PWM Output mode only) 0101 = ECCP2 output (PWM Output mode only) 0100 = ECCP1 output (PWM Output mode only) 0011 = Reference Clock Output Module 1 (REFO1) signal 0010 = MDCIN2 pin 0001 = MDCIN1 pin 0000 = No carrier input (tied to ground) Note 1: Narrowed carrier pulse widths or spurs may occur in the signal stream during transitions.  2012-2016 Microchip Technology Inc. DS30000575C-page 243 PIC18F97J94 FAMILY 13.0 LIQUID CRYSTAL DISPLAY (LCD) CONTROLLER • Up to 60 segments (in 100-pin devices when 1/5-1/8 multiplex is selected), 64 (in 100-pin devices when up to 1/4 multiplex is selected), 46 (in 80-pin devices when 1/5-1/8 multiplex is selected), 50 (in 80-pin devices when up to 1/4 multiplex is selected), 30 (in 64-pin devices when 1/5-1/8 multiplex is selected) and 34 (in 64-pin devices when up to 1/4 multiplex is selected) • Static, 1/2 or 1/3 LCD bias • On-chip bias generator with dedicated charge pump to support a range of fixed and variable bias options • Internal resistors for bias voltage generation • Software contrast control for LCD using the internal biasing The Liquid Crystal Display (LCD) driver module generates the timing control to drive a static or multiplexed LCD panel. In 100-pin devices (PIC18F97J94), the module drives panels of up to eight commons and up to 60 segments when 5 to 8 commons are used, and up to 64 segments when 1 to 4 commons are used. It also provides control of the LCD pixel data. The LCD driver module supports: • Direct driving of LCD panel • Three LCD clock sources with selectable prescaler • Up to eight commons: - Static (One common) - 1/2 multiplex (two commons) - 1/3 multiplex (three commons) - 1/8 multiplex (eight commons) FIGURE 13-1: A simplified block diagram of the module is shown in Figure 13-1. LCD CONTROLLER MODULE BLOCK DIAGRAM Data Bus LCD DATA 64 x 8 8 LCDDATA63 512 LCDDATA62 . . . to 64 LCDDATA1 MUX 64 SEG LCDDATA0 Bias Voltage To I/O Pins Timing Control LCDCON 8 LCDPS LCDSEx COM LCD Bias Generation Resistor Ladder FRC Oscillator LPRC Oscillator SOSC (Secondary Oscillator) DS30000575C-page 244 LCD Clock Source Select LCD Charge Pump  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 13.1 LCD Registers The LCDCON register, shown in Register 13-1, controls the overall operation of the module. Once the module is configured, the LCDEN (LCDCON) bit is used to enable or disable the LCD module. The LCD panel can also operate during Sleep by clearing the SLPEN (LCDCON) bit. The LCD controller has up to 77 registers: • LCD Control Register (LCDCON) • LCD Phase Register (LCDPS) • LCD Voltage Regulator Control Register (LCDREG) • LCD Reference Ladder Control Register (LCDREF and LCDRL) • Eight LCD Segment Enable Registers (LCDSE7:LCDSE0) • 64 LCD Data Registers (LCDDATA63:LCDDATA0) REGISTER 13-1: The LCDPS register, shown in Register 13-3, configures the LCD clock source prescaler and the type of waveform: Type-A or Type-B. For details on these features, see Section 13.3 “LCD Clock Source Selection” and Section 13.12 “LCD Waveform Generation”. LCDCON: LCD CONTROL REGISTER R/W-0 R/W-0 R/C-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LCDEN SLPEN WERR CS1 CS0 LMUX2 LMUX1 LMUX0 bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 LCDEN: LCD Driver Enable bit 1 = LCD driver module is enabled 0 = LCD driver module is disabled bit 6 SLPEN: LCD Driver Enable in Sleep mode bit 1 = LCD driver module is disabled in Sleep mode 0 = LCD driver module is enabled in Sleep mode bit 5 WERR: LCD Write Failed Error bit 1 = LCDDATAx register is written while WA (LCDPS) = 0 (must be cleared in software) 0 = No LCD write error bit 4-3 CS: Clock Source Select bits 00 = FRC (8 MHz)/8192 01 = SOSC Oscillator (32.768 kHz)/32 1x = INTRC (31.25 kHz)/32 bit 2-0 LMUX: Commons Select bits LMUX Multiplex Bias 111 110 101 100 011 010 001 000 1/8 MUX (COM) 1/7 MUX (COM) 1/6 MUX (COM) 1/5 MUX (COM) 1/4 MUX (COM) 1/3 MUX (COM) 1/2 MUX (COM) Static (COM0) 1/3 1/3 1/3 1/3 1/3 1/2 or 1/3 1/2 or 1/3 Static  2012-2016 Microchip Technology Inc. DS30000575C-page 245 PIC18F97J94 FAMILY REGISTER 13-2: LCDREG: LCD CHARGE PUMP CONTROL REGISTER R/W-0 U-0 RW-1 RW-1 RW-1 RW-1 RW-0 RW-0 CPEN — BIAS2 BIAS1 BIAS0 MODE13 CLKSEL1 CLKSEL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 CPEN: 3.6V Charge Pump Enable bit 1 = The regulator generates the highest (3.6V) voltage 0 = Highest voltage in the system is supplied externally (VDD) bit 6 Unimplemented: Read as ‘0’ bit 5-3 BIAS: Regulator Voltage Output Control bits 111 =3.60V peak (offset on LCDBIAS0 of 0V) 110 =3.47V peak (offset on LCDBIAS0 of 0.13V) 101 =3.34V peak (offset on LCDBIAS0 of 0.26V) 100 =3.21V peak (offset on LCDBIAS0 of 0.39V) 011 =3.08V peak (offset on LCDBIAS0 of 0.52V) 010 =2.95V peak (offset on LCDBIAS0 of 0.65V) 001 =2.82V peak (offset on LCDBIAS0 of 0.78V) 000 =2.69V peak (offset on LCDBIAS0 of 0.91V) bit 2 MODE13: 1/3 LCD BIAS Enable bit 1 = Regulator output supports 1/3 LCD BIAS mode 0 = Regulator output supports Static LCD BIAS mode bit 1-0 CLKSEL: Regulator Clock Select Control bits 11 =LPRC 10 =FRC 01 =SOSC 00 =Disable regulator and float regulator voltage output. DS30000575C-page 246 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 13-3: LCDPS: LCD PHASE REGISTER R/W-0 R/W-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0 WFT BIASMD LCDA WA LP3 LP2 LP1 LP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 WFT: Waveform Type Select bit 1 = Type-B waveform (phase changes on each frame boundary) 0 = Type-A waveform (phase changes within each common type) bit 6 BIASMD: Bias Mode Select bit When LMUX = 000 or 011 through 111: 0 = Static Bias mode (LMUX = 000) / 1/3 Bias mode (LMUX = 011 through 111) (do not set this bit to ‘1’) When LMUX = 001 or 010: 1 = 1/2 Bias mode 0 = 1/3 Bias mode bit 5 LCDA: LCD Active Status bit 1 = LCD driver module is active 0 = LCD driver module is inactive bit 4 WA: LCD Write Allow Status bit 1 = Writes into the LCDDATAx registers is allowed 0 = Writes into the LCDDATAx registers is not allowed bit 3-0 LP: LCD Prescaler Select bits 1111 = 1:16 1110 = 1:15 1101 = 1:14 1100 = 1:13 1011 = 1:12 1010 = 1:11 1001 = 1:10 1000 = 1:9 0111 = 1:8 0110 = 1:7 0101 = 1:6 0100 = 1:5 0011 = 1:4 0010 = 1:3 0001 = 1:2 0000 = 1:1  2012-2016 Microchip Technology Inc. DS30000575C-page 247 PIC18F97J94 FAMILY 13.2 LCD Segment Pins Configuration The LCDSEx registers configure the functions of the port pins. Setting the segment enable bit for a particular segment configures that pin as an LCD driver. There TABLE 13-1: are four LCD Segment Enable registers, as shown in Table 13-1. The prototype LCDSEx register is shown in Register 13-4. LCDSEx REGISTERS AND ASSOCIATED SEGMENTS Register Segments LCDSE0 Seg 7:Seg 0 LCDSE1 Seg 15:Seg 8 LCDSE2 Seg 23:Seg 16 LCDSE3 Seg 31:Seg 24 LCDSE4 Seg 39:Seg 32 LCDSE5 Seg 47:Seg 40 LCDSE6 Seg 55:Seg 48 LCDSE7 Seg 63:Seg 56 Once the module is initialized for the LCD panel, the individual bits of the LCDDATAx registers are cleared or set to represent a clear or dark pixel, respectively. Specific sets of LCDDATA registers are used with specific segments and common signals. Each bit represents a unique combination of a specific segment connected to a specific common. REGISTER 13-4: Individual LCDDATA bits are named by the convention, “SxxCy”, with “xx” as the segment number and “y” as the common number. The relationship is summarized in Register 13-3. The prototype LCDDATAx register is shown in Register 13-5. LCDSEx: LCD SEGMENT x ENABLE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SE(n) SE(n) SE(n) SE(n) SE(n) SE(n) SE(n) SE(n) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 x = Bit is unknown SE(n): Segment Enable bits For LCDSE0: n = 0-7 For LCDSE1: n = 8-15 For LCDSE2: n = 16-23 For LCDSE3: n = 24-31 For LCDSE0: n = 32-39 For LCDSE0: n = 40-47 For LCDSE0: n = 48-55 For LCDSE0: n = 56-63 1 = Segment function of the pin is enabled, digital I/O is disabled 0 = Segment function of the pin is disabled, digital I/O is enabled DS30000575C-page 248  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 13-5: LCDDATAx: LCD DATA x REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 S(n)Cy S(n)Cy S(n)Cy S(n)Cy S(n)Cy S(n)Cy S(n)Cy S(n)Cy bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 S(n)Cy: Pixel On bits For registers LCDDATA0 through LCDDATA7: n = (0-63), y = 0 For registers LCDDATA8 through LCDDATA15: n = (0-63), y = 1 For registers LCDDATA16 through LCDDATA23: n = (0-63), y = 2 For registers LCDDATA24 through LCDDATA31: n = (0-63), y = 3 For registers LCDDATA32 through LCDDATA39: n = (0-63), y = 4 For registers LCDDATA40 through LCDDATA47: n = (0-63), y = 5 For registers LCDDATA48 through LCDDATA55: n = (0-63), y = 6 For registers LCDDATA56 through LCDDATA63: n = (0-63), y = 7 1 = Pixel on 0 = Pixel off TABLE 13-2: COM Lines x = Bit is unknown LCDDATA REGISTERS AND BITS FOR SEGMENT AND COM COMBINATIONS Segments 0 to 7 8 to 15 16 to 23 24 to 31 32 to 39 0 LCDDATA0 S00C0:S07C0 LCDDATA1 S08C0:S15C0 LCDDATA2 S16C0:S23C0 LCDDATA3 S24C0:S31C0 LCDDATA4 S32C0:S39C0 LCDDATA5 LCDDATA6 LCDDATA7 S40C0:S47C0 S48C0:S55C0 S56C0:S63C0 1 LCDDATA8 S00C1:S07C1 LCDDATA9 S08C1:S15C1 LCDDATA10 S16C1:S23C1 LCDDATA11 S24C1:S31C1 LCDDATA12 S32C1:S39C1 LCDDATA13 LCDDATA14 LCDDATA15 S40C1:S47C1 S48C1:S55C1 S56C1:S63C1 2 LCDDATA16 S00C2:S07C2 LCDDATA17 S08C2:S15C2 LCDDATA18 S16C2:S23C2 LCDDATA19 S24C2:S31C2 LCDDATA20 S32C2:S39C2 3 LCDDATA24 S00C3:S07C3 LCDDATA25 S08C3:S15C3 LCDDATA26 S16C3:S23C3 LCDDATA27 S24C3:S31C3 LCDDATA28 S32C3:S39C3 LCDDATA29 LCDDATA30 LCDDATA31 S40C3:S47C3 S48C3:S55C3 S56C3:S63C3 4 LCDDATA32 S00C4:S07C4 LCDDATA33 S08C4:S15C4 LCDDATA34 S16C4:S23C4 LCDDATA35 S24C4:S31C4 LCDDATA36 S32C4:S39C4 LCDDATA37 LCDDATA38 LCDDATA39 S40C4:S47C4 S48C4:S55C4 S56C4:S63C4 5 LCDDATA40 S00C5:S07C5 LCDDATA41 S08C5:S15C5 LCDDATA42 S16C5:S23C5 LCDDATA43 S24C5:S31C5 LCDDATA44 S32C5:S39C5 LCDDATA46 LCDDATA47 LCDDATA45 S40C5:S47C5 S48C5:S55C5 S56C5:S63C5 6 LCDDATA48 S00C6:S07C6 LCDDATA49 S08C6:S15C6 LCDDATA50 S16C6:S23C6 LCDDATA51 S24C6:S31C6 LCDDATA52 S32C6:S39C6 LCDDATA53 LCDDATA54 LCDDATA55 S40C6:S47C6 S48C6:S55C6 S56C6:S63C6 7 LCDDATA56 S00C7:S07C7 LCDDATA57 S08C7:S15C7 LCDDATA58 S16C7:S23C7 LCDDATA59 S24C7:S31C7 LCDDATA60 S32C7:S39C7 LCDDATA61 LCDDATA62 LCDDATA63 S40C7:S47C7 S48C7:S55C7 S56C7:S63C7  2012-2016 Microchip Technology Inc. 40 to 47 LCDDATA21 40C2:S47C2 48 to 55 56 to 63 LCDDATA22 LCDDATA23 S48C2:S55C2 S56C2:S63C2 DS30000575C-page 249 PIC18F97J94 FAMILY 13.3 LCD Clock Source Selection The LCD driver module has three possible clock sources: • FRC/8192 • SOSC Clock/32 The third clock source is a 31.25 kHz internal LPRC Oscillator/32 that provides approximately 1 kHz output. The second and third clock sources may be used to continue running the LCD while the processor is in Sleep. These clock sources are selected through the bits, CS (LCDCON). • LPRC/32 The first clock source is the 8 MHz Fast Internal RC (FRC) Oscillator divided by 8,192. This divider ratio is chosen to provide about 1 kHz output. The divider is not programmable. Instead, the LCD prescaler bits, LCDPS, are used to set the LCD frame clock rate. 13.3.1 The second clock source is the SOSC Oscillator/32. This also outputs about 1 kHz when a 32.768 kHz crystal is used with the SOSC Oscillator. To use the SOSC Oscillator as a clock source, set the SOSCEN (T1CON) bit. Selectable prescale values are from 1:1 through 1:16, in increments of one. A 16-bit counter is available as a prescaler for the LCD clock. The prescaler is not directly readable or writable. Its value is set by the LP bits (LCDPS) that determine the prescaler assignment and prescale ratio. LCD CLOCK GENERATION FRC Oscillator (8 MHZ) SOSC Oscillator (32 kHz) COM0 COM1 COM2 COM7 FIGURE 13-2: LCD PRESCALER ÷8192 ÷32 ÷4 STAT ÷2 1/2 MUX 4-Bit Prog Prescaler ÷1, 2, 3....8 Ring Counter 1/3 to 1/8 LPRC Oscillator (31.25 kHz) ÷32 CS (LCDCON) DS30000575C-page 250 MUX LP (LCDPS) LMUX (LCDCON) LMUX (LCDCON)  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 13.4 LCD Bias Types 13.5 The LCD module can be configured in one of three bias types: Internal Resistor Biasing This mode does not use external resistors, but rather internal resistor ladders that are configured to generate the bias voltage. • Static bias (two voltage levels: VSS and VDD) • 1/2 bias (three voltage levels: VSS, 1/2 VDD and VDD) • 1/3 bias (four voltage levels: VSS, 1/3 VDD, 2/3 VDD and VDD) The internal reference ladder actually consists of three separate ladders. Disabling the internal reference ladder disconnects all of the ladders, allowing external voltages to be supplied. Depending on the total resistance of the resistor ladders, the biasing can be classified as low, medium or high power. LCD bias voltages can be generated with internal resistor ladders, internal bias generator or external resistor ladder. Table 13-3 shows the total resistance of each of the ladders. Table 13-3 shows the internal resister ladder connections. When the internal resistor ladder is selected, the bias voltage can either be from VDD or from VDDCORE, depending on the LCDIRS setting. It can also provide software contrast control (using LCDCST) . TABLE 13-3: INTERNAL RESISTANCE LADDER POWER MODES Power Mode Nominal Resistance of Entire Ladder IDD Low 3 MΩ 1 µA Medium 300 kΩ 10 µA High 30 kΩ 100 µA  2012-2016 Microchip Technology Inc. DS30000575C-page 251 PIC18F97J94 FAMILY FIGURE 13-3: LCD BIAS INTERNAL RESISTOR LADDER CONNECTION DIAGRAM DD VVDD VDDCORE 3x Band Gap LCDIRS LCDIRE LCDCST VLCD3PE LCDBIAS3 VLCD2PE LCDBIAS2 VLCD1PE LCDBIAS1 Low Resistor Ladder Medium Resistor Ladder High Resistor Ladder A Power Mode B Power Mode LRLAT LRLAP LRLBP There are two power modes, designated as “Mode A” and “Mode B”. Mode A is set by the LRLAP bits and Mode B by the LRLB bits. The resistor ladder to use for Modes A and B are selected by the bits, LRLAP and LRLBP, respectively. Each ladder has a matching contrast control ladder, tuned to the nominal resistance of the reference ladder. This contrast control resistor can be controlled by the LCDCST bits (LCDREF). Disabling the internal reference ladder results in all of the ladders being disconnected, allowing external voltages to be supplied. DS30000575C-page 252 To get additional current in High-Power mode, when LRLAP (LCDRL) = 11, both the medium and high-power resistor ladders are activated. Whenever the LCD module is inactive, LCDA (LCDPS) = 0), the reference ladder will be turned off.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 13.5.1 AUTOMATIC POWER MODE SWITCHING (LCDRL) select how long or if the Mode A is active. Mode B Power mode is active for the remaining time before the segments or commons change again. As an LCD segment is electrically only a capacitor, current is drawn only during the interval when the voltage is switching. To minimize total device current, the LCD reference ladder can be operated in a different power mode for the transition portion of the duration. This is controlled by the LCDREF and LCDRL registers. As shown in Figure 13-4, there are 32 counts in a single segment time. Type-A can be chosen during the time when the wave form is in transition. Type-B can be used when the clock is stable or not in transition. By using this feature of automatic power switching using Type-A/Type-B, the power consumption can be optimized for a given contrast. Mode A Power mode is active for a programmable time, beginning at the time when the LCD segment waveform is transitioning. The LRLAT bits FIGURE 13-4: LCD REFERENCE LADDER POWER MODE SWITCHING DIAGRAM Single Segment Time lcd_32x_clk cnt 'H00 'H01 'H02 'H03 'H04 'H05 'H06 'H07 'H1E 'H1F 'H00 'H01 lcd_clk 'H3 LRLAT Segment Data LRLAT Power Mode Power Mode A  2012-2016 Microchip Technology Inc. Power Mode B Mode A DS30000575C-page 253 PIC18F97J94 FAMILY 13.5.2 CONTRAST CONTROL The LCD contrast control circuit consists of a 7-tap resistor ladder, controlled by the LCDCSTx bits (see Figure 13-5) FIGURE 13-5: INTERNAL REFERENCE AND CONTRAST CONTROL BLOCK DIAGRAM 7 Stages VDD R R R R Analog MUX 7 0 To Top of Reference Ladder LCDCST 3 Internal Reference 13.5.3 Contrast Control INTERNAL REFERENCE Under firmware control, an internal reference for the LCD bias voltages can be enabled. When enabled, the source of this voltage can be VDD. When no internal reference is selected, the LCD contrast control circuit is disabled and LCD bias must be provided externally. Whenever the LCD module is inactive (LCDA = 0), the internal reference will be turned off. DS30000575C-page 254 13.5.4 VLCDxPE PINS The VLCD3PE, VLCD2PE and VLCD1PE pins provide the ability for an external LCD bias network to be used instead of the internal ladder. Use of the VLCDxPE pins does not prevent use of the internal ladder. Each VLCDxPE pin has an independent control in the LCDREF register, allowing access to any or all of the LCD bias signals. This architecture allows for maximum flexibility in different applications. The VLCDxPE pins could be used to add capacitors to the internal reference ladder for increasing the drive capacity. For applications where the internal contrast control is insufficient, the firmware can choose to enable only the VLCD3PE pin, allowing an external contrast control circuit to use the internal reference divider.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 13-6: LCDREF: LCD REFERENCE LADDER CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LCDIRE — LCDCST2 LCDCST1 LCDCST0 VLCD3PE VLCD2PE VLCD1PE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 LCDIRE: LCD Internal Reference Enable bit 1 = Internal LCD reference is enabled and connected to the internal contrast control circuit 0 = Internal LCD reference is disabled bit 6 Unimplemented: Read as ‘0’ bit 5-3 LCDCST: LCD Contrast Control bits Selects the Resistance of the LCD Contrast Control Resistor Ladder: 111 =Resistor ladder is at maximum resistance (minimum contrast) 110 =Resistor ladder is at 6/7th of maximum resistance 101 =Resistor ladder is at 5/7th of maximum resistance 100 =Resistor ladder is at 4/7th of maximum resistance 011 =Resistor ladder is at 3/7th of maximum resistance 010 =Resistor ladder is at 2/7th of maximum resistance 001 =Resistor ladder is at 1/7th of maximum resistance 000 =Minimum resistance (maximum contrast); resistor ladder is shorted bit 2 VLCD3PE: Bias3 Pin Enable bit 1 = BIAS3 level is connected to the external pin, LCDBIAS3 0 = BIAS3 level is internal (internal resistor ladder) bit 1 VLCD2PE: Bias2 Pin Enable bit 1 = BIAS2 level is connected to the external pin, LCDBIAS2 0 = BIAS2 level is internal (internal resistor ladder) bit 0 VLCD1PE: Bias1 Pin Enable bit 1 = BIAS1 level is connected to the external pin, LCDBIAS1 0 = BIAS1 level is internal (internal resistor ladder)  2012-2016 Microchip Technology Inc. DS30000575C-page 255 PIC18F97J94 FAMILY REGISTER 13-7: LCDRL: LCD REFERENCE LADDER CONTROL REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 LRLAP1 LRLAP0 LRLBP1 LRLBP0 — LRLAT2 LRLAT1 LRLAT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 LRLAP: LCD Reference Ladder A Time Power Control bits During Time Interval A: 11 = Internal LCD reference ladder is powered in High-Power mode 10 = Internal LCD reference ladder is powered in Medium Power mode 01 = Internal LCD reference ladder is powered in Low-Power mode 00 = Internal LCD reference ladder is powered down and unconnected bit 5-4 LRLBP: LCD Reference Ladder B Time Power Control bits During Time Interval B: 11 = Internal LCD reference ladder is powered in High-Power mode 10 = Internal LCD reference ladder is powered in Medium Power mode 01 = Internal LCD reference ladder is powered in Low-Power mode 00 = Internal LCD reference ladder is powered down and unconnected bit 3 Unimplemented: Read as ‘0’ bit 2-0 LRLAT: LCD Reference Ladder A Time Interval Control bits Sets the number of 32 clock counts when the A Time Interval Power mode is active. For Type-A Waveforms (WFT = 0): 111 = Internal LCD reference ladder is in A Power mode for 7 clocks and B Power mode for 9 clocks 110 = Internal LCD reference ladder is in A Power mode for 6 clocks and B Power mode for 10 clocks 101 = Internal LCD reference ladder is in A Power mode for 5 clocks and B Power mode for 11 clocks 100 = Internal LCD reference ladder is in A Power mode for 4 clocks and B Power mode for 12 clocks 011 = Internal LCD reference ladder is in A Power mode for 3 clocks and B Power mode for 13 clocks 010 = Internal LCD reference ladder is in A Power mode for 2 clocks and B Power mode for 14 clocks 001 = Internal LCD reference ladder is in A Power mode for 1 clock and B Power mode for 15 clocks 000 = Internal LCD reference ladder is always in B Power mode For Type-B Waveforms (WFT = 1): 111 = Internal LCD reference ladder is in A Power mode for 7 clocks and B Power mode for 25 clocks 110 = Internal LCD reference ladder is in A Power mode for 6 clocks and B Power mode for 26 clocks 101 = Internal LCD reference ladder is in A Power mode for 5 clocks and B Power mode for 27 clocks 100 = Internal LCD reference ladder is in A Power mode for 4 clocks and B Power mode for 28 clocks 011 = Internal LCD reference ladder is in A Power mode for 3 clocks and B Power mode for 29 clocks 010 = Internal LCD reference ladder is in A Power mode for 2 clocks and B Power mode for 30 clocks 001 = Internal LCD reference ladder is in A Power mode for 1 clock and B Power mode for 31 clocks 000 = Internal LCD reference ladder is always in B Power mode DS30000575C-page 256  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 13.5.5 LCD BIAS GENERATION 13.5.7 The LCD driver module is capable of generating the required bias voltages for LCD operation with a minimum of external components. This includes the ability to generate the different voltage levels required by the different bias types that are required by the LCD. The driver module can also provide bias voltages, both above and below microcontroller VDD, through the use of an on-chip LCD voltage regulator. 13.5.6 LCD BIAS TYPES PIC18F97J94 family devices support three bias types, based on the waveforms generated to control segments and commons: • Static (two discrete levels) • 1/2 Bias (three discrete levels) • 1/3 Bias (four discrete levels) LCD VOLTAGE REGULATOR The purpose of the LCD regulator is to provide proper bias voltage and good contrast for the LCD, regardless of VDD levels. This module contains a charge pump and internal voltage reference. The regulator can be configured by using external components to boost bias voltage above VDD. It can also operate a display at a constant voltage below VDD. The regulator can also be selectively disabled to allow bias voltages to be generated by an external resistor network. The LCD regulator is controlled through the LCDREG register. It is enabled or disabled using the CLKSEL bits, while the charge pump can be selectively enabled using the CPEN bit. When the regulator is enabled, the MODE13 bit is used to select the bias type. The peak LCD bias voltage, measured as a difference between the potentials of LCDBIAS3 and LCDBIAS0, is configured with the BIAS bits. The use of different waveforms in driving the LCD is discussed in more detail in Section 13.12 “LCD Waveform Generation”. REGISTER 13-8: LCDREG: LCD VOLTAGE REGULATOR CONTROL REGISTER R/W-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-0 R/W-0 CPEN — BIAS2 BIAS1 BIAS0 MODE13 CLKSEL1 CLKSEL 0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 CPEN: LCD Charge Pump Enable bit 1 = Charge pump is enabled; highest LCD bias voltage is 3.6V 0 = Charge pump is disabled; highest LCD bias voltage is VDD bit 6 Unimplemented: Read as ‘0’ bit 5-3 BIAS: Regulator Voltage Output Control bits 111 = 3.60V peak (offset on LCDBIAS0 of 0V) 110 = 3.47V peak (offset on LCDBIAS0 of 0.13V) 101 = 3.34V peak (offset on LCDBIAS0 of 0.26V) 100 = 3.21V peak (offset on LCDBIAS0 of 0.39V) 011 = 3.08V peak (offset on LCDBIAS0 of 0.52V) 010 = 2.95V peak (offset on LCDBIAS0 of 0.65V) 001 = 2.82V peak (offset on LCDBIAS0 of 0.78V) 000 = 2.69V peak (offset on LCDBIAS0 of 0.91V) bit 2 MODE13: 1/3 LCD Bias Enable bit 1 = Regulator output supports 1/3 LCD Bias mode 0 = Regulator output supports Static LCD Bias mode bit 1-0 CLKSEL: Regulator Clock Source Select bits 11 = 31 kHz LPRC 10 = 8 MHz FRC 01 = SOSC 00 = LCD regulator disabled  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 257 PIC18F97J94 FAMILY 13.6 BIAS CONFIGURATIONS PIC18F97J94 family devices have four distinct circuit configurations for LCD bias generation: • • • • M0: Regulator with Boost M1: Regulator without Boost M2: Resistor Ladder with Software Contrast M3: Resistor Ladder with Hardware Contrast 13.6.1 M0 (REGULATOR WITH BOOST) In M0 operation, the LCD charge pump feature is enabled. This allows the regulator to generate voltages up to +3.6V to the LCD (as measured at LCDBIAS3). M0 uses a flyback capacitor connected between VLCAP1 and VLCAP2, as well as filter capacitors on LCDBIAS0 through LCDBIAS3, to obtain the required voltage boost (Figure 13-6). The output voltage (VBIAS) is the difference of the potential between LCDBIAS3 and LCDBIAS0. It is set by the BIAS bits which adjust the offset between LCDBIAS0 and VSS. The flyback capacitor (CFLY) acts as a charge storage element for large LCD loads. This mode is useful in those cases where the voltage requirements of the LCD are higher than the microcontroller’s VDD. It also permits software control of the display’s contrast, by adjustment of bias voltage, by changing the value of the BIAS bits. M0 supports static and 1/3 bias types. Generation of the voltage levels for 1/3 bias is handled automatically, but must be configured in software. 13.6.2 M1 (REGULATOR WITHOUT BOOST) M1 operation is similar to M0, but does not use the LCD charge pump. It can provide VBIAS up to the voltage level supplied directly to LCDBIAS3. It can be used in cases where VDD for the application is expected to never drop below a level that can provide adequate contrast for the LCD. The connection of external components is very similar to M0, except that LCDBIAS3 must be tied directly to VDD (Figure 13-6). Note: When the device is put to Sleep while operating in mode M0 or M1, make sure that the bias capacitors are fully discharged to get the lowest Sleep current. The BIAS bits can still be used to adjust contrast in software by changing the VBIAS. As with M0, changing these bits changes the offset between LCDBIAS0 and VSS. In M1, this is reflected in the change between the LCDBIAS0 and the voltage tied to LCDBIAS3. Thus, if VDD should change, VBIAS will also change; where in M0, the level of VBIAS is constant. Like M0, M1 supports static and 1/3 bias types. Generation of the voltage levels for 1/3 bias is handled automatically but must be configured in software. M1 is enabled by selecting a valid regulator clock source (CLKSEL set to any value except ‘00’) and clearing the CPEN bit. If 1/3 bias type is required, the MODE13 bit should also be set. M0 is enabled by selecting a valid regulator clock source (CLKSEL set to any value except ‘00’) and setting the CPEN bit. If static bias type is required, the MODE13 bit must be cleared. DS30000575C-page 258  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 13-6: LCD REGULATOR CONNECTIONS FOR M0 AND M1 CONFIGURATIONS PIC18F97J94 VLCAP1 VLCAP2 LCDBIAS3 LCDBIAS2 LCDBIAS1 LCDBIAS0 Mode 0 (VBIAS up to 3.6V) Note 1: CFLY 0.47 F(1) 0.47 F(1) VDD C3 0.47 F(1) C2 0.47 F(1) C1 0.47 F(1) C0 0.47 F(1) C2 0.47 F(1) C1 0.47 F(1) C0 0.47 F(1) Mode 1 (VBIAS  VDD) These values are provided for design guidance only; they should be optimized for the application by the designer based on the actual LCD specifications.  2012-2016 Microchip Technology Inc. DS30000575C-page 259 PIC18F97J94 FAMILY 13.6.3 M2 (EXTERNAL RESISTOR LADDER WITH SOFTWARE CONTRAST) LCDBIAS0. The bias type is determined by the voltages on the LCDBIAS pins, which are controlled by the configuration of the resistor ladder. Most applications, using M2, will use a 1/3 or 1/2 bias type. While static bias can also be used, it offers extremely limited contrast range and additional current consumption over other bias generation modes. M2 operation also uses the LCD regulator but disables the charge pump. The regulator’s internal voltage reference remains active as a way to regulate contrast. It is used in cases where the current requirements of the LCD exceed the capacity of the regulator’s charge pump. Like M1, the LCDBIAS bits can be used to control contrast, limited by the level of VDD supplied to the device. Also, since there is no capacitor required across VLCAP1 and VLCAP2, these pins are available as digital I/O ports, RG2 and RG3. M2 is selected by clearing the CLKSEL bits and setting the CPEN bit. In this configuration, the LCD bias voltage levels are created by an external resistor voltage divider, connected across LCDBIAS0 through LCDBIAS3, with the top of the divider tied to VDD (Figure 13-7). The potential at the bottom of the ladder is determined by the LCD regulator’s voltage reference, tied internally to FIGURE 13-7: RESISTOR LADDER CONNECTIONS FOR M2 CONFIGURATION PIC18F97J94 VDD VDD LCDBIAS3 10 k(1) 10 k(1) LCDBIAS2 10 k(1) LCDBIAS1 10 k(1) 10 k(1) LCDBIAS0 1/2 Bias Bias Level at Pin Note 1: 1/3 Bias Bias Type 1/2 Bias 1/3 Bias LCDBIAS0 (Internal Low Reference Voltage) (Internal Low Reference Voltage) LCDBIAS1 1/2 VBIAS 1/3 VBIAS LCDBIAS2 1/2 VBIAS 2/3 VBIAS LCDBIAS3 VBIAS (up to VDD) VBIAS (up to VDD) These values are provided for design guidance only; they should be optimized for the application by the designer based on the actual LCD specifications. DS30000575C-page 260  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 13.6.4 M3 (HARDWARE CONTRAST) In M3, the LCD regulator is completely disabled. Like M2, LCD bias levels are tied to VDD and are generated using an external divider. The difference is that the internal voltage reference is also disabled and the bottom of the ladder is tied to ground (VSS); see Figure 138. The value of the resistors, and the difference between VSS and VDD, determine the contrast range; no software adjustment is possible. This configuration FIGURE 13-8: is also used where the LCD’s current requirements exceed the capacity of the charge pump and software contrast control is not needed. Depending on the bias type required, resistors are connected between some or all of the pins. A potentiometer can also be connected between LCDBIAS3 and VDD to allow for hardware controlled contrast adjustment. M3 is selected by clearing the CLKSEL and CPEN bits. RESISTOR LADDER CONNECTIONS FOR M3 CONFIGURATION PIC18F97J94 VDD VDD VDD (2) LCDBIAS3 10 k(1) 10 k(1) LCDBIAS2 10 k(1) LCDBIAS1 10 k(1) 10 k(1) LCDBIAS0 Static Bias Bias Level at Pin Note 1: 2: 1/2 Bias 1/3 Bias Bias Type Static 1/2 Bias 1/3 Bias LCDBIAS0 AVSS AVSS AVSS LCDBIAS1 AVSS 1/2 VDD 1/3 VDD LCDBIAS2 VDD 1/2 VDD 2/3 VDD LCDBIAS3 VDD VDD VDD These values are provided for design guidance only; they should be optimized for the application by the designer based on the actual LCD specifications. A potentiometer for manual contrast adjustment is optional; it may be omitted entirely.  2012-2016 Microchip Technology Inc. DS30000575C-page 261 PIC18F97J94 FAMILY 13.7 Design Considerations for the LCD Charge Pump When designing applications that use the LCD regulator with the charge pump enabled, users must always consider both the dynamic current and RMS (static) current requirements of the display, and what the charge pump can deliver. Both dynamic and static current can be determined by Equation 13-1: EQUATION 13-1: LCD STATIC, DYNAMIC CURRENT I=Cx dV dt For dynamic current, C, is the value of the capacitors attached to LCDBIAS3 and LCDBIAS2. The variable, dV, is the voltage drop allowed on C2 and C3 during a voltage switch on the LCD display, and dt is the duration of the transient current after a clock pulse occurs. For practical design purposes, it will be assumed to be 0.047 µF for C, 0.1V for dV and 1 µs for dt. This yields a dynamic current of 4.7 mA for 1 µs. RMS current is determined by the value of CFLY for C, the voltage across VLCAP1 and VLCAP2 for dV and the regulator clock period (TPER) for dt. Assuming a CFLY value of 0.047 µF, a value of 1.02V across CFLY and TPER of 30 µs, the maximum theoretical static current will be 1.8 mA. Since the charge pump must charge five capacitors, the maximum current becomes 360 µA. For a real-world assumption of 50% efficiency, this yields a practical current of 180 µA. Users should compare the calculated current capacity against the TABLE 13-4: LMUX requirements of the LCD. While dV and dt are relatively fixed by device design, the values of CFLY and the capacitors on the LCDBIAS pins can be changed to increase or decrease current. As always, any changes should be evaluated in the actual circuit for their impact on the application. 13.8 LCD Multiplex Types The LCD driver module can be configured into four multiplex types: • • • • • • • • Static (only COM0 used) 1/2 multiplex (COM0 and COM1 are used) 1/3 multiplex (COM0, COM1 and COM2 are used) 1/4 multiplex (COM0, COM1, COM2 and COM3 are used) 1/5 multiplex (COM0, COM1, COM2, COM3 and COM4 are used) 1/6 multiplex (COM0, COM1, COM2, COM3, COM4 and COM5 are used) 1/7 multiplex (COM0, COM1, COM2, COM3, COM4, COM5 and COM6 are used) 1/8 multiplex (COM0, COM1, COM2, COM3, COM4, COM5, COM6 and COM7 are used) The LMUX setting (LCDCON) decides the function of the COM pins. (For details, see Table 13-4). If the pin is a digital I/O, the corresponding TRIS bit controls the data direction. If the pin is a COM drive, the TRIS setting of that pin is overridden. Note: On a Power-on Reset, the LMUX bits are ‘000’. COM PIN FUNCTIONS COM7 Pin COM6 Pin COM5 Pin COM4 Pin COM3 Pin COM2 Pin COM1 Pin COM0 Pin 111 COM7 COM6 COM5 COM4 COM3 COM2 COM1 COM0 110 I/O Pin COM6 COM5 COM4 COM3 COM2 COM1 COM0 101 I/O Pin I/O Pin COM5 COM4 COM3 COM2 COM1 COM0 100 I/O Pin I/O Pin I/O Pin COM4 COM3 COM2 COM1 COM0 011 I/O Pin I/O Pin I/O Pin I/O Pin COM3 COM2 COM1 COM0 010 I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin COM2 COM1 COM0 001 I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin COM1 COM0 000 I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin COM0 Note: Pins, COM, can also be used as SEG pins when ¼ multiplex to static multiplex are used. These pins can be used as I/O pins only if respective bits in the LCDSEx registers are set to ‘0’. 13.9 Segment Enables The LCDSEx registers are used to select the pin function for each segment pin. The selection allows each pin to operate as either an LCD segment driver or a digital only pin. To configure the pin as a segment pin, the corresponding bits in the LCDSEx registers must be set to ‘1’. DS30000575C-page 262 If the pin is a digital I/O, the corresponding TRIS bit controls the data direction. Any bit set in the LCDSEx registers overrides any bit settings in the corresponding TRIS register. Note: On a Power-on Reset, these pins are configured as digital I/O.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 13.10 Pixel Control The LCDDATAx registers contain bits that define the state of each pixel. Each bit defines one unique pixel. Table 13-2 shows the correlation of each bit in the LCDDATAx registers to the respective common and segment signals. TABLE 13-5: Any LCD pixel location not being used for display can be used as general purpose RAM. 13.11 LCD Frame Frequency The rate at which the COM and SEG outputs change is called the LCD frame frequency. FRAME FREQUENCY FORMULAS Multiplex Note: Static (‘000’) 1/2 (‘001’) 1/3 (‘010’) 1/4 (‘011’) 1/5 (‘100’) 1/6 (‘101’) 1/7 (‘110’) 1/8 (‘111’) The clock source is FRC/8192, SOSC/32 or LPRC/32. Frame Frequency = Clock Source/(4 x 1 x (LP + 1)) Clock Source/(2 x 2 x (LP + 1)) Clock Source/(1 x 3 x (LP + 1)) Clock Source/(1 x 4 x (LP + 1)) Clock Source/(1 x 5 x (LP + 1)) Clock Source/(1 x 6 x (LP + 1)) Clock Source/(1 x 7 x (LP + 1)) Clock Source/(1 x 8 x (LP + 1)) 13.12 LCD Waveform Generation LCD waveform generation is based on the philosophy that the net AC voltage across the dark pixel should be maximized and the net AC voltage across the clear pixel should be minimized. The net DC voltage across any pixel should be zero. The COM signal represents the time slice for each common, while the SEG contains the pixel data. The pixel signal (COM-SEG) will have no DC component and can take only one of the two rms values. The higher rms value will create a dark pixel and a lower rms value will create a clear pixel. As the number of commons increases, the delta between the two rms values decreases. The delta represents the maximum contrast that the display can have. The LCDs can be driven by two types of waveforms: Type-A and Type-B. In a Type-A waveform, the phase changes within each common type, whereas a Type-B waveform’s phase changes on each frame boundary. Thus, Type-A waveforms maintain 0 VDC over a single frame, whereas Type-B waveforms take two frames. Note: If Sleep has to be executed with LCD Sleep enabled (SLPEN (LCDCON) = 1), care must be taken to execute Sleep only when VDC on all the pixels is ‘0’. Figure 13-9 through Figure 13-21 provide waveforms for static, half-multiplex, one-third multiplex and quarter multiplex drives for Type-A and Type-B waveforms.  2012-2016 Microchip Technology Inc. DS30000575C-page 263 PIC18F97J94 FAMILY FIGURE 13-9: TYPE-A/TYPE-B WAVEFORMS IN STATIC DRIVE V1 COM0 V0 COM0 V1 SEG0 V0 V1 SEG1 SEG0 SEG2 SEG7 SEG6 SEG5 SEG4 SEG3 SEG1 V0 V1 V0 COM0-SEG0 -V1 COM0-SEG1 V0 1 Frame DS30000575C-page 264  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 13-10: TYPE-A WAVEFORMS IN 1/2 MUX, 1/2 BIAS DRIVE V2 COM0 V1 V0 COM1 V2 COM0 COM1 V1 V0 V2 V1 SEG0 V0 SEG0 SEG1 SEG2 SEG3 V2 V1 SEG1 V0 V2 V1 V0 COM0-SEG0 -V1 -V2 V2 V1 V0 COM0-SEG1 -V1 -V2 1 Frame  2012-2016 Microchip Technology Inc. DS30000575C-page 265 PIC18F97J94 FAMILY FIGURE 13-11: TYPE-B WAVEFORMS IN 1/2 MUX, 1/2 BIAS DRIVE V2 V1 COM0 COM1 V0 COM0 V2 COM1 V1 V0 V2 SEG0 V1 SEG0 SEG1 SEG2 SEG3 V0 V2 SEG1 V1 V0 V2 V1 V0 COM0-SEG0 -V1 -V2 V2 V1 V0 COM0-SEG1 -V1 -V2 2 Frames DS30000575C-page 266  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 13-12: TYPE-A WAVEFORMS IN 1/2 MUX, 1/3 BIAS DRIVE V3 V2 COM0 V1 COM1 V0 V3 COM0 V2 COM1 V1 V0 V3 V2 SEG0 V1 V0 V2 SEG1 SEG0 SEG1 SEG2 SEG3 V3 V1 V0 V3 V2 V1 V0 COM0-SEG0 -V1 -V2 -V3 V3 V2 V1 V0 COM0-SEG1 -V1 -V2 1 Frame  2012-2016 Microchip Technology Inc. -V3 DS30000575C-page 267 PIC18F97J94 FAMILY FIGURE 13-13: TYPE-B WAVEFORMS IN 1/2 MUX, 1/3 BIAS DRIVE V3 V2 COM0 V1 COM1 V0 V3 COM0 V2 COM1 V1 V0 V3 V2 SEG0 V1 V0 SEG0 SEG1 SEG2 SEG3 V3 V2 SEG1 V1 V0 V3 V2 V1 V0 COM0-SEG0 -V1 -V2 -V3 V3 V2 V1 V0 COM0-SEG1 -V1 -V2 2 Frames DS30000575C-page 268 -V3  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 13-14: TYPE-A WAVEFORMS IN 1/3 MUX, 1/2 BIAS DRIVE V2 COM0 V1 V0 COM2 V2 COM1 V1 V0 COM1 COM0 V2 COM2 V1 V0 V2 SEG0 SEG2 V1 SEG0 SEG1 SEG2 V0 V2 SEG1 V1 V0 V2 V1 V0 COM0-SEG0 -V1 -V2 V2 V1 V0 COM0-SEG1 -V1 -V2 1 Frame  2012-2016 Microchip Technology Inc. DS30000575C-page 269 PIC18F97J94 FAMILY FIGURE 13-15: TYPE-B WAVEFORMS IN 1/3 MUX, 1/2 BIAS DRIVE V2 COM0 V1 V0 COM2 V2 COM1 V1 COM1 V0 COM0 V2 COM2 V1 V0 V2 V1 V0 SEG0 SEG1 SEG2 SEG0 V2 SEG1 V1 V0 V2 V1 V0 COM0-SEG0 -V1 -V2 V2 V1 V0 COM0-SEG1 -V1 -V2 2 Frames DS30000575C-page 270  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 13-16: TYPE-A WAVEFORMS IN 1/3 MUX, 1/3 BIAS DRIVE V3 V2 COM0 V1 V0 V3 COM2 V2 COM1 V1 COM1 V0 COM0 V3 V2 COM2 V1 V0 V3 V2 V1 V0 SEG0 SEG1 SEG2 SEG0 SEG2 V3 V2 SEG1 V1 V0 V3 V2 V1 V0 COM0-SEG0 -V1 -V2 -V3 V3 V2 V1 V0 COM0-SEG1 -V1 -V2 -V3 1 Frame  2012-2016 Microchip Technology Inc. DS30000575C-page 271 PIC18F97J94 FAMILY FIGURE 13-17: TYPE-B WAVEFORMS IN 1/3 MUX, 1/3 BIAS DRIVE V3 V2 COM0 V1 V0 V3 COM2 V2 COM1 V1 COM1 V0 COM0 V3 V2 COM2 V1 V0 V3 V2 V1 V0 SEG0 SEG1 SEG2 SEG0 V3 V2 SEG1 V1 V0 V3 V2 V1 V0 COM0-SEG0 -V1 -V2 -V3 V3 V2 V1 V0 COM0-SEG1 -V1 -V2 -V3 2 Frames DS30000575C-page 272  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 13-18: TYPE-A WAVEFORMS IN 1/4 MUX, 1/3 BIAS DRIVE COM3 COM0 V3 V2 V1 V0 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 COM3 V3 V2 V1 V0 SEG0 V3 V2 V1 V0 SEG1 V3 V2 V1 V0 COM0-SEG0 V3 V2 V1 V0 -V1 -V2 -V3 COM0-SEG1 V3 V2 V1 V0 -V1 -V2 -V3 COM2 COM1 SEG0 SEG1 COM0 1 Frame  2012-2016 Microchip Technology Inc. DS30000575C-page 273 PIC18F97J94 FAMILY FIGURE 13-19: TYPE-B WAVEFORMS IN 1/4 MUX, 1/3 BIAS DRIVE COM3 COM2 COM1 COM0 V3 V2 V1 V0 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 COM3 V3 V2 V1 V0 SEG0 V3 V2 V1 V0 SEG1 V3 V2 V1 V0 COM0-SEG0 V3 V2 V1 V0 -V1 -V2 -V3 COM0-SEG1 V3 V2 V1 V0 -V1 -V2 -V3 SEG0 SEG1 COM0 2 Frames DS30000575C-page 274  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 13-20: TYPE-A WAVEFORMS IN 1/8 MUX, 1/3 BIAS DRIVE COM4 COM0 COM5 COM3 COM7 COM2 COM6 COM1 COM1 COM0 COM2 COM7 SEG0 SEG0 COM0-SEG0 COM1-SEG0  2012-2016 Microchip Technology Inc. V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 -V1 -V2 -V3 V3 V2 V1 V0 -V1 -V2 -V3 DS30000575C-page 275 PIC18F97J94 FAMILY FIGURE 13-21: TYPE-B WAVEFORMS IN 1/8 MUX, 1/3 BIAS DRIVE COM4 COM3 COM5 COM0 COM7 COM2 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 COM6 COM1 COM0 COM7 SEG0 SEG0 COM0 - SEG0 COM1 - SEG0 DS30000575C-page 276 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 -V1 -V2 -V3 V3 V2 V1 V0 -V1 -V2 -V3  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 13.13 LCD Interrupts When the LCD driver is running with Type-B waveforms, and the LMUX bits are not equal to ‘000’, there are some additional issues. The LCD timing generation provides an interrupt that defines the LCD frame timing. This interrupt can be used to coordinate the writing of the pixel data with the start of a new frame, which produces a visually crisp transition of the image. Since the DC voltage on the pixel takes two frames to maintain 0V, the pixel data must not change between subsequent frames. If the pixel data were allowed to change, the waveform for the odd frames would not necessarily be the complement of the waveform generated in the even frames and a DC component would be introduced into the panel. This interrupt can also be used to synchronize external events to the LCD. For example, the interface to an external segment driver can be synchronized for segment data updates to the LCD frame. Because of this, using Type-B waveforms requires synchronizing the LCD pixel updates to occur within a subframe after the frame interrupt. A new frame is defined as beginning at the leading edge of the COM0 common signal. The interrupt will be set immediately after the LCD controller completes accessing all pixel data required for a frame. This will occur at a fixed interval before the frame boundary (TFINT), as shown in Figure 13-22. To correctly sequence writing in Type-B, the interrupt only occurs on complete phase intervals. If the user attempts to write when the write is disabled, the WERR bit (LCDCON) is set. The LCD controller will begin to access data for the next frame within the interval from the interrupt to when the controller begins accessing data after the interrupt (TFWR). New data must be written within TFWR, as this is when the LCD controller will begin to access the data for the next frame. FIGURE 13-22: Note: The interrupt is not generated when the Type-A waveform is selected and when the Type-B with no multiplex (static) is selected. EXAMPLE WAVEFORMS AND INTERRUPT TIMING IN QUARTER DUTY CYCLE DRIVE LCD Interrupt Occurs Controller Accesses Next Frame Data COM0 V3 V2 V1 V0 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 V3 V2 V1 V0 COM3 2 Frames TFINT Frame Boundary Frame Boundary TFWR Frame Boundary TFWR = TFRAME/2 * (LMUX + 1) + TCY/2 TFINT = (TFWR/2 – (2 TCY + 40 ns)) Minimum = 1.5(TFRAME/4) – (2 TCY + 40 ns) (TFWR/2 – (1 TCY + 40 ns)) Maximum = 1.5(TFRAME/4) – (1 TCY + 40 ns)  2012-2016 Microchip Technology Inc. DS30000575C-page 277 PIC18F97J94 FAMILY 13.14 Configuring the LCD Module 13.15 Operation During Sleep To configure the LCD module. The LCD module can operate during Sleep. The selection is controlled by the SLPEN bit (LCDCON). Setting the SLPEN bit allows the LCD module to go to Sleep. Clearing the SLPEN bit allows the module to continue to operate during Sleep. 1. 2. 3. 4. 5. 6. 7. Select the frame clock prescale using bits, LP (LCDPS). Configure the appropriate pins to function as segment drivers using the LCDSEx registers. If using the internal reference resistors for biasing, enable the internal reference ladder and: • Define the Mode A and Mode B interval by using the LRLAT bits (LCDRL) • Define the low, medium or high ladder for Mode A and Mode B by using the LRLAP bits (LCDRL) and the LRLBP bits (LCDRL), respectively • Set the VLCDxPE bits and enable the LCDIRE bit (LCDREF) Configure the following LCD module functions using the LCDCON register: • Multiplex and Bias mode – LMUX bits • Timing Source – CS bits • Sleep mode – SLPEN bit Write initial values to the Pixel Data registers, LCDDATA0 through LCDDATA63. Clear the LCD Interrupt Flag, LCDIF, and if desired, enable the interrupt by setting bit, LCDIE. Enable the LCD module by setting the LCDEN bit (LCDCON) DS30000575C-page 278 If a SLEEP instruction is executed and SLPEN = 1, the LCD module will cease all functions and go into a very Low-Current Consumption mode. The module will stop operation immediately and drive the minimum LCD voltage on both segment and common lines. Figure 13-23 shows this operation. The LCD module current consumption will not decrease in this mode, but the overall consumption of the device will be lower due to shut down of the core and other peripheral functions. To ensure that no DC component is introduced on the panel, the SLEEP instruction should be executed immediately after an LCD frame boundary. The LCD interrupt can be used to determine the frame boundary. See Section 13.13 “LCD Interrupts” for the formulas to calculate the delay. If a SLEEP instruction is executed and SLPEN = 0, the module will continue to display the current contents of the LCDDATA registers. The LCD data cannot be changed.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 13-23: SLEEP ENTRY/EXIT WHEN SLPEN = 1 OR CS = 00. V3 V2 V1 COM0 V0 V3 V2 V1 V0 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 SEG0 2 Frames SLEEP Instruction Execution  2012-2016 Microchip Technology Inc. Wake-up DS30000575C-page 279 PIC18F97J94 FAMILY 14.0 TIMER0 MODULE The Timer0 module incorporates the following features: • Software-selectable operation as a timer or counter in both 8-bit or 16-bit modes • Readable and writable registers • Dedicated 8-bit, software programmable prescaler • Selectable clock source (internal or external) • Edge select for external clock • Interrupt-on-overflow REGISTER 14-1: The T0CON register (Register 14-1) controls all aspects of the module’s operation, including the prescale selection. It is both readable and writable. Figure 14-1 provides a simplified block diagram of the Timer0 module in 8-bit mode. Figure 14-2 provides a simplified block diagram of the Timer0 module in 16-bit mode. T0CON: TIMER0 CONTROL REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 TMR0ON T08BIT T0CS1 T0CS0 PSA T0PS2 T0PS1 T0PS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 TMR0ON: Timer0 On/Off Control bit 1 = Enables Timer0 0 = Stops Timer0 bit 6 T08BIT: Timer0 8-Bit/16-Bit Control bit 1 = Timer0 is configured as an 8-bit timer/counter 0 = Timer0 is configured as a 16-bit timer/counter bit 5-4 T0CS: Timer0 Clock Source Select bit 11 = Increment on high-to-low transition on T0CKI pin 10 = Increment on low-to-high transition on T0CKI pin 01 = Internal clock (FOSC/4) 00 = INTOSC bit 3 PSA: Timer0 Prescaler Assignment bit 1 = Timer0 prescaler is not assigned; Timer0 clock input bypasses prescaler 0 = Timer0 prescaler is assigned; Timer0 clock input comes from prescaler output bit 2-0 T0PS: Timer0 Prescaler Select bits 111 = 1:256 Prescale value 110 = 1:128 Prescale value 101 = 1:64 Prescale value 100 = 1:32 Prescale value 011 = 1:16 Prescale value 010 = 1:8 Prescale value 001 = 1:4 Prescale value 000 = 1:2 Prescale value DS30000575C-page 280  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 14.1 Timer0 Operation 14.2 Timer0 can operate in one of these two modes: TMR0H is not the actual high byte of Timer0 in 16-bit mode. It is actually a buffered version of the real high byte of Timer0, which is not directly readable nor writable (see Figure 14-2). TMR0H is updated with the contents of the high byte of Timer0 during a read of TMR0L. This provides the ability to read all 16 bits of Timer0 without having to verify that the read of the high and low byte were valid, due to a rollover between successive reads of the high and low byte. • As an 8-bit (T08BIT = 1) or 16-bit (T08BIT = 0) timer • As an asynchronous 8-bit (T08BIT = 1) or 16-bit (T08BIT = 0) counter 14.1.1 TIMER MODE In Timer mode, Timer0 either increments every CPU clock cycle, or every instruction cycle, depending on the clock select bit, TMR0CS (T0CON). 14.1.2 Similarly, a write to the high byte of Timer0 must also take place through the TMR0H Buffer register. The high byte is updated with the contents of TMR0H when a write occurs to TMR0L. This allows all 16 bits of Timer0 to be updated at once. COUNTER MODE In this mode, Timer0 is incremented via a rising or falling edge of an external source on the T0CKI pin. The clock select bits, TMR0CS, must be set to ‘1x’. FIGURE 14-1: Timer0 Reads and Writes in 16-Bit Mode TIMER0 BLOCK DIAGRAM (8-BIT MODE) FOSC/4 0 1 1 Programmable Prescaler T0CKI Pin T0SE T0CS 0 Sync with Internal Clocks Set TMR0IF on Overflow TMR0L (2 TCY Delay) 8 3 T0PS 8 PSA Internal Data Bus Note: Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale. FIGURE 14-2: FOSC/4 TIMER0 BLOCK DIAGRAM (16-BIT MODE) 0 1 1 T0CKI Pin T0SE T0CS Programmable Prescaler 0 Sync with Internal Clocks TMR0 High Byte TMR0L 8 Set TMR0IF on Overflow (2 TCY Delay) 3 Read TMR0L T0PS Write TMR0L PSA 8 8 TMR0H 8 8 Internal Data Bus Note: Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale.  2012-2016 Microchip Technology Inc. DS30000575C-page 281 PIC18F97J94 FAMILY 14.3 Prescaler An 8-bit counter is available as a prescaler for the Timer0 module. The prescaler is not directly readable or writable. Its value is set by the PSA and T0PS bits (T0CON), which determine the prescaler assignment and prescale ratio. Clearing the PSA bit assigns the prescaler to the Timer0 module. When it is assigned, prescale values from 1:2 through 1:256 in power-of-two increments are selectable. When assigned to the Timer0 module, all instructions writing to the TMR0 register (for example, CLRF TMR0, MOVWF TMR0, BSF TMR0) clear the prescaler count. Note: Writing to TMR0 when the prescaler is assigned to Timer0 will clear the prescaler count but will not change the prescaler assignment. DS30000575C-page 282 14.3.1 SWITCHING PRESCALER ASSIGNMENT The prescaler assignment is fully under software control and can be changed “on-the-fly” during program execution. 14.4 Timer0 Interrupt The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h in 8-bit mode, or from FFFFh to 0000h in 16-bit mode. This overflow sets the TMR0IF flag bit. The interrupt can be masked by clearing the TMR0IE bit (INTCON). Before reenabling the interrupt, the TMR0IF bit must be cleared in software by the Interrupt Service Routine (ISR). Since Timer0 is shutdown in Sleep mode, the TMR0 interrupt cannot awaken the processor from Sleep.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 15.0 TIMER1/3/5 MODULES The Timer1/3/5 timer/counter modules incorporate these features: • Software-selectable operation as a 16-bit timer or counter • Readable and writable 8-bit registers (TMRxH and TMRxL) • Selectable clock source (internal or external) with device clock or SOSC Oscillator internal options • Interrupt-on-overflow • Module Reset on ECCP Special Event Trigger A simplified block diagram of the Timer1/3/5 module is shown in Figure 15-1. The Timer1/3/5 module is controlled through the TxCON register (Register 15-1). It also selects the clock source options for the ECCP modules. (For more information, see Section 18.1.1 “ECCP Module and Timer Resources”). The FOSC clock source should not be used with the ECCP capture/compare features. If the timer will be used with the capture or compare features, always select one of the other timer clocking options. Note: Throughout this section, generic references are used for register and bit names that are the same – except for an ‘x’ variable that indicates the item’s association with the Timer1, Timer3 or Timer5 module. For example, the control register is named TxCON and refers to T1CON, T3CON and T5CON.  2012-2016 Microchip Technology Inc. DS30000575C-page 283 PIC18F97J94 FAMILY REGISTER 15-1: TxCON: TIMERx CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TMRxCS1 TMRxCS0 TxCKPS1 TxCKPS0 SOSCEN TxSYNC RD16 TMRxON bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 TMRxCS: Timerx Clock Source Select bits 11 = Timerx Clock source is INTOSC 10 = Timerx clock source depends on the SOSCEN bit: SOSCEN = 0: External clock from the TxCKI pin (on the rising edge). SOSCEN = 1: Depending on the SOSCSEL fuses, either a crystal oscillator on the SOSCI/SOSCO pins or an external clock from the SCLKI pin. 01 = Timerx clock source is the system clock (FOSC)(1) 00 = Timerx clock source is the instruction clock (FOSC/4) bit 5-4 TxCKPS: Timerx Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value bit 3 SOSCEN: SOSC Oscillator Enable bit 1 = SOSC/SCLKI are enabled for Timerx (based on the SOSCSEL fuses) 0 = SOSC/SCLKI are disabled for Timerx and TxCKI is enabled bit 2 TxSYNC: Timerx External Clock Input Synchronization Control bit (Not usable if the device clock comes from Timer1/3/5.) When TMRxCS = 10: 1 = Do not synchronize external clock input 0 = Synchronize external clock input When TMRxCS = 0x: This bit is ignored; Timer1/3/5 uses the internal clock. bit 1 RD16: 16-Bit Read/Write Mode Enable bit 1 = Enables register read/write of Timerx in one 16-bit operation 0 = Enables register read/write of Timerx in two 8-bit operations bit 0 TMRxON: Timerx On bit 1 = Enables Timerx 0 = Stops Timerx Note 1: The FOSC clock source should not be selected if the timer will be used with the ECCP capture/compare features. DS30000575C-page 284  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 15.1 Timer1/3/5 Gate Control Register The Timer1/3/5 Gate Control register (TxGCON), provided in Register 15-2, is used to control the Timerx gate. REGISTER 15-2: TxGCON: TIMERx GATE CONTROL REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R-x R/W-0 R/W-0 TMRxGE TxGPOL TxGTM TxGSPM TxGGO/TxDONE TxGVAL TxGSS1 TxGSS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 TMRxGE: Timerx Gate Enable bit If TMRxON = 0: This bit is ignored. If TMRxON = 1: 1 = Timerx counting is controlled by the Timerx gate function 0 = Timerx counts regardless of Timerx gate function bit 6 TxGPOL: Timerx Gate Polarity bit 1 = Timerx gate is active-high (Timerx counts when gate is high) 0 = Timerx gate is active-low (Timerx counts when gate is low) bit 5 TxGTM: Timerx Gate Toggle Mode bit 1 = Timerx Gate Toggle mode is enabled. 0 = Timerx Gate Toggle mode is disabled and toggle flip-flop is cleared Timerx gate flip-flop toggles on every rising edge. bit 4 TxGSPM: Timerx Gate Single Pulse Mode bit 1 = Timerx Gate Single Pulse mode is enabled and is controlling Timerx gate 0 = Timerx Gate Single Pulse mode is disabled bit 3 TxGGO/TxDONE: Timerx Gate Single Pulse Acquisition Status bit 1 = Timerx gate single pulse acquisition is ready, waiting for an edge 0 = Timerx gate single pulse acquisition has completed or has not been started This bit is automatically cleared when TxGSPM is cleared. bit 2 TxGVAL: Timerx Gate Current State bit Indicates the current state of the Timerx gate that could be provided to TMRxH:TMRxL; unaffected by the Timerx Gate Enable (TMRxGE) bit. bit 1-0 TxGSS: Timerx Gate Source Select bits 11 = Comparator 2 output 10 = Comparator 1 output 01 = TMR(x+1) to match PR(x+1) output(2) 00 = Timer1 gate pin The Watchdog Timer Oscillator is turned on if TMRxGE = 1, regardless of the state of TMRxON. Note 1: 2: Programming the TxGCON prior to TxCON is recommended. Timer(x+1) will be Timer1/3/5 for Timerx (Timer1/3/5), respectively.  2012-2016 Microchip Technology Inc. DS30000575C-page 285 PIC18F97J94 FAMILY 15.2 Timer1/3/5 Operation The operating mode is determined by the clock select bits, TMRxCSx (TxCON). When the TMRxCSx bits are cleared (= 00), Timer1/3/5 increments on every internal instruction cycle (FOSC/4). When TMRxCSx = 01, the Timer1/3/5 clock source is the system clock (FOSC). When it is ‘10’, Timer1/3/5 works as a counter from the external clock from the TxCKI pin (on the rising edge after the first falling edge) or the SOSC Oscillator. When it is ‘11’, the Timer1/3/5 clock source is INTOSC. Timer1, Timer3 and Timer5 can operate in these modes: • • • • Timer Synchronous Counter Asynchronous Counter Timer with Gated Control FIGURE 15-1: TIMER1/3/5 BLOCK DIAGRAM T3GSS T3G 00 From TMR4 Match PR4 01 From Comparator 1 Output 10 From Comparator 2 Output 11 T3GSPM 0 T3G_IN 1 TMR3ON T3GPOL T3GVAL Single Pulse Acq. Control 0 D Q CK R Q 1 Q1 T3GGO/ T3DONE D Q Data Bus RD T3GCON EN Interrupt det Set TMR3GIF T3GTM TMR3GE Set Flag bit TMR3IF on Overflow TMR3ON TMR3(2) TMR3H EN TMR3L Q D Synchronized Clock Input 0 T3CLK 1 TMR3CS SOSCO/SCLKI SOSC SOSCI det 10 EN T1CON.SOSCEN T1CON.SOSCEN SOSCGO NOSC = 100 (1) Note 1: 2: 3: 4: Synchronize(3) Prescaler 1, 2, 4, 8 1 0 T3CKI T3SYNC OUT(4) FOSC Internal Clock 01 Timer3 Clock is INTOSC 01 FOSC/4 Internal Clock 00 2 T3CKPS FOSC/2 Internal Clock Sleep Input ST buffer is a high-speed type when using T3CKI. Timer3 registers increment on the rising edge. Synchronization does not operate while in Sleep. The output of SOSC is determined by the SOSCSEL Configuration bits. DS30000575C-page 286  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 15.3 Timer1/3/5 16-Bit Read/Write Mode Timer1/3/5 can be configured for 16-bit reads and writes (see Figure 15-3). When the RD16 control bit (TxCON) is set, the address for TMRxH is mapped to a buffer register for the high byte of Timer1/3/5. A read from TMRxL will load the contents of the high byte of Timer1/3/5 into the Timerx High Byte Buffer register. This provides users with the ability to accurately read all 16 bits of Timer1/3/5 without having to determine whether a read of the high byte, followed by a read of the low byte, has become invalid due to a rollover between reads. 15.4 Using the SOSC Oscillator as the Timer1/3/5 Clock Source The SOSC Internal Oscillator may be used as the clock source for Timer1/3/5. It can be enabled in one of these ways: • Setting the SOSCEN bit in either of the TxCON registers (TxCON) • Setting the SOSCGO bit in the OSCCON2 register (OSCCON2) • Setting the NOSC bits to secondary clock source in the OSCCON register (OSCCON = 100) A write to the high byte of Timer1/3/5 must also take place through the TMRxH Buffer register. The Timer1/3/5 high byte is updated with the contents of TMRxH when a write occurs to TMRxL. This allows users to write all 16 bits to both the high and low bytes of Timer1/3/5 at once. The SOSCGO bit is used to warm up the SOSC so that it is ready before any peripheral requests it. The high byte of Timer1/3/5 is not directly readable or writable in this mode. All reads and writes must take place through the Timerx High Byte Buffer register. The SOSC Oscillator is described in Section 15.4 “Using the SOSC Oscillator as the Timer1/3/5 Clock Source”. To use it as the Timer3 clock source, the TMR3CSx bits must also be set. As previously noted, this also configures Timer3 to increment on every rising edge of the oscillator source. Writes to TMRxH do not clear the Timer1/3/5 prescaler. The prescaler is only cleared on writes to TMRxL.  2012-2016 Microchip Technology Inc. DS30000575C-page 287 PIC18F97J94 FAMILY 15.5 Timer1/3/5 Gates When Timerx Gate Enable mode is enabled, Timer1/3/5 will increment on the rising edge of the Timer1/3/5 clock source. When Timerx Gate Enable mode is disabled, no incrementing will occur and Timer1/3/5 will hold the current count. See Figure 15-2 for timing details. Timer1/3/5 can be configured to count freely or the count can be enabled and disabled using the Timer1/3/5 gate circuitry. This is also referred to as the Timer1/3/5 gate count enable. TABLE 15-1: The Timer1/3/5 gate can also be driven by multiple selectable sources. 15.5.1 TIMER1/3/5 GATE COUNT ENABLE TxCLK(†) The Timerx Gate Enable mode is enabled by setting the TMRxGE bit (TxGCON). The polarity of the Timerx Gate Enable mode is configured using the TxGPOL bit (TxGCON). TIMER1/3/5 GATE ENABLE SELECTIONS TxGPOL TxG Pin (TxGCON) Timerx Operation  0 0 Counts  0 1 Holds Count  1 0 Holds Count  1 1 Counts † The clock on which TMR1/3/5 is running. For more information, see TxCLK in Figure 15-1. FIGURE 15-2: TIMER1/3/5 GATE COUNT ENABLE MODE TMRxGE TxGPOL TxG_IN TxCKI TxGVAL Timer1/3/5 DS30000575C-page 288 N N+1 N+2 N+3 N+4  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 15.5.2 TIMER1/3/5 GATE SOURCE SELECTION The Timer1/3/5 gate source can be selected from one of four different sources. Source selection is controlled by the TxGSS bits (TxGCON). The polarity for each available source is also selectable and is controlled by the TxGPOL bit (TxGCON ). TABLE 15-2: TIMER1/3/5 GATE SOURCES TxGSS Timerx Gate Source 00 Timerx Gate Pin 01 TMR(x+1) to Match PR(x+1) (TMR(x+1) increments to match PR(x+1)) 10 Comparator 1 Output (comparator logic high output) 11 Comparator 2 Output (comparator logic high output) 15.5.2.1 TxG Pin Gate Operation The TxG pin is one source for Timer1/3/5 gate control. It can be used to supply an external source to the Timerx gate circuitry. 15.5.2.2 Timer2/4/6/8 Match Gate Operation The TMR(x+1) register will increment until it matches the value in the PR(x+1) register. On the very next increment cycle, TMR2 will be reset to 00h. When this Reset occurs, a low-to-high pulse will automatically be generated and internally supplied to the Timerx gate circuitry. The pulse will remain high for one instruction cycle and will return back to a low state until the next match. FIGURE 15-3: Depending on TxGPOL, Timerx increments differently when TMR(x+1) matches PR(x+1). When TxGPOL = 1, Timerx increments for a single instruction cycle following a TMR(x+1) match with PR(x+1). When TxGPOL = 0, Timerx increments continuously, except for the cycle following the match, when the gate signal goes from low-to-high. 15.5.2.3 Comparator 1 Output Gate Operation The output of Comparator1 can be internally supplied to the Timerx gate circuitry. After setting up Comparator 1 with the CM1CON register, Timerx will increment depending on the transitions of the C1OUT (CMSTAT) bit. 15.5.2.4 Comparator 2 Output Gate Operation The output of Comparator 2 can be internally supplied to the Timerx gate circuitry. After setting up Comparator 2 with the CM2CON register, Timerx will increment depending on the transitions of the C2OUT (CMSTAT) bit. 15.5.3 TIMER1/3/5 GATE TOGGLE MODE When Timer1/3/5 Gate Toggle mode is enabled, it is possible to measure the full cycle length of a Timer1/3/5 gate signal, as opposed to the duration of a single level pulse. The Timerx gate source is routed through a flip-flop that changes state on every incrementing edge of the signal. (For timing details, see Figure 15-3.) The TxGVAL bit will indicate when the Toggled mode is active and the timer is counting. Timer1/3/5 Gate Toggle mode is enabled by setting the TxGTM bit (TxGCON). When the TxGTM bit is cleared, the flip-flop is cleared and held clear. This is necessary in order to control which edge is measured. TIMER1/3/5 GATE TOGGLE MODE TMRxGE TxGPOL TxGTM TxG_IN TxCKI TxGVAL Timer1/3/5 N  2012-2016 Microchip Technology Inc. N+1 N+2 N+3 N+4 N+5 N+6 N+7 N+8 DS30000575C-page 289 PIC18F97J94 FAMILY 15.5.4 TIMER1/3/5 GATE SINGLE PULSE MODE No other gate events will be allowed to increment Timer1/3/5 until the TxGGO/TxDONE bit is once again set in software. When Timer1/3/5 Gate Single Pulse mode is enabled, it is possible to capture a single pulse gate event. Timer1/3/5 Gate Single Pulse mode is first enabled by setting the TxGSPM bit (TxGCON). Next, the TxGGO/ TxDONE bit (TxGCON) must be set. Clearing the TxGSPM bit also will clear the TxGGO/ TxDONE bit. (For timing details, see Figure 15-4.) Simultaneously enabling the Toggle mode and the Single Pulse mode will permit both sections to work together. This allows the cycle times on the Timer1/3/5 gate source to be measured. (For timing details, see Figure 15-5.) The Timer1/3/5 will be fully enabled on the next incrementing edge. On the next trailing edge of the pulse, the TxGGO/TxDONE bit will automatically be cleared. FIGURE 15-4: TIMER1/3/5 GATE SINGLE PULSE MODE TMRxGE TxGPOL TxGSPM TxGGO/ Cleared by Hardware on Falling Edge of TxGVAL Set by Software TxDONE Counting Enabled on Rising Edge of TxG TxG_IN TxCKI TxGVAL Timer1/3/5 TMRxGIF DS30000575C-page 290 N Cleared by Software N+1 N+2 Set by Hardware on Falling Edge of TxGVAL Cleared by Software  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 15-5: TIMER1/3/5 GATE SINGLE PULSE AND TOGGLE COMBINED MODE TMRxGE TxGPOL TxGSPM TxGTM TxGGO/ Cleared by Hardware on Falling Edge of TxGVAL Set by Software TxDONE Counting Enabled on Rising Edge of TxG TxG_IN TxCKI TxGVAL Timer1/3/5 TMRxGIF 15.5.5 N Cleared by Software TIMER1/3/5 GATE VALUE STATUS When Timer1/3/5 gate value status is utilized, it is possible to read the most current level of the gate control value. The value is stored in the TxGVAL bit (TxGCON). The TxGVAL bit is valid even when the Timer1/3/5 gate is not enabled (TMRxGE bit is cleared). N+1 N+2 N+3 Set by Hardware on Falling Edge of TxGVAL 15.5.6 N+4 Cleared by Software TIMER1/3/5 GATE EVENT INTERRUPT When the Timer1/3/5 gate event interrupt is enabled, it is possible to generate an interrupt upon the completion of a gate event. When the falling edge of TxGVAL occurs, the TMRxGIF flag bit in the PIRx register will be set. If the TMRxGIE bit in the PIEx register is set, then an interrupt will be recognized. The TMRxGIF flag bit operates even when the Timer1/3/5 gate is not enabled (TMRxGE bit is cleared).  2012-2016 Microchip Technology Inc. DS30000575C-page 291 PIC18F97J94 FAMILY 15.6 Timer1/3/5 Interrupt The TMRx register pair (TMRxH:TMRxL) increments from 0000h to FFFFh and overflows to 0000h. The Timerx interrupt, if enabled, is generated on overflow and is latched in the interrupt flag bit, TMRxIF. Table 15-3 gives each module’s flag bit. TABLE 15-3: TIMER1/3/5 INTERRUPT FLAG BITS Timer Module Flag Bit 1 PIR1 3 PIR2 5 PIR5 This interrupt can be enabled or disabled by setting or clearing the TMRxIE bit, respectively. Table 15-4 gives each module’s enable bit. TABLE 15-4: TIMER1/3/5 INTERRUPT ENABLE BITS Timer Module Flag Bit 1 PIE1 3 PIE2 5 PIE5 DS30000575C-page 292 15.7 Resetting Timer1/3/5 Using the ECCP Special Event Trigger If the ECCP modules are configured to use Timerx and to generate a Special Event Trigger in Compare mode (CCPxM = 1011), this signal will reset Timerx. The trigger from ECCP2 will also start an A/D conversion if the A/D module is enabled (For more information, see Section 18.3.4 “Special Event Trigger”.) The module must be configured as either a timer or synchronous counter to take advantage of this feature. When used this way, the CCPRxH:CCPRxL register pair effectively becomes a Period register for Timerx. If Timerx is running in Asynchronous Counter mode, the Reset operation may not work. In the event that a write to Timerx coincides with a Special Event Trigger from an ECCP module, the write will take precedence. Note: The Special Event Triggers from the ECCPx module will only clear the TMR3 register’s content, but not set the TMR3IF interrupt flag bit (PIR1). Note: The CCP and ECCP modules use Timers, 1 through 8, for some modes. The assignment of a particular timer to a CCP/ECCP module is determined by the Timer to CCP enable bits in the CCPTMRSx registers. For more details, see Register 18-2, Register 18-3 and Register 19-2  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 16.0 TIMER2/4/6/8 MODULES The Timer2/4/6/8 timer modules have the following features: • • • • • • 8-Bit Timer register (TMRx) 8-Bit Period register (PRx) Readable and Writable (all registers) Software Programmable Prescaler (1:1, 1:4, 1:16) Software Programmable Postscaler (1:1 to 1:16) Interrupt on TMRx Match of PRx Note: Throughout this section, generic references are used for register and bit names that are the same, except for an ‘x’ variable that indicates the item’s association with the Timer2, Timer4, Timer6 or Timer8 module. For example, the control register is named TxCON and refers to T2CON, T4CON, T6CON and T8CON. The Timer2/4/6/8 modules have a control register, shown in Register 16-1. Timer2/4/6/8 can be shut off by clearing control bit, TMRxON (TxCON), to minimize power consumption. The prescaler and postscaler selection of Timer2/4/6/8 also are controlled by this register. Figure 16-1 is a simplified block diagram of the Timer2/4/6/8 modules. 16.1 Timer2/4/6/8 Operation Timer2/4/6/8 can be used as the PWM time base for the PWM mode of the ECCP modules. The TMRx registers are readable and writable, and are cleared on any device Reset. The input clock (FOSC/4) has a prescale option of 1:1, 1:4 or 1:16, selected by control bits, TxCKPS (TxCON). The match output of TMRx goes through a four-bit postscaler (that gives a 1:1 to 1:16 inclusive scaling) to generate a TMRx interrupt, latched in the flag bit, TMRxIF. Table 16-1 gives each module’s flag bit. TABLE 16-1: The interrupt can be enabled or disabled by setting or clearing the Timerx Interrupt Enable bit (TMRxIE), shown in Table 16-2. TABLE 16-2: TIMER2/4/6/8 INTERRUPT ENABLE BITS Timer Module Flag Bit 2 PIE1 4 PIE5 6 PIE5 8 PIE5 The prescaler and postscaler counters are cleared when any of the following occurs: • A write to the TMRx register • A write to the TxCON register • Any device Reset – Power-on Reset (POR), MCLR Reset, Watchdog Timer Reset (WDTR) or Brown-out Reset (BOR) A TMRx is not cleared when a TxCON is written. Note: The CCP and ECCP modules use Timers, 1 through 8, for some modes. The assignment of a particular timer to a CCP/ECCP module is determined by the Timer to CCP enable bits in the CCPTMRSx registers. For more details, see Register 18-2, Register 18-3 and Register 19-2. TIMER2/4/6/8 FLAG BITS Timer Module Flag Bit 2 PIR1 4 PIR5 6 PIR5 8 PIR5  2012-2016 Microchip Technology Inc. DS30000575C-page 293 PIC18F97J94 FAMILY REGISTER 16-1: TxCON: TIMERx CONTROL REGISTER (TIMER2/4/6/8) U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — TxOUTPS3 TxOUTPS2 TxOUTPS1 TxOUTPS0 TMRxON TxCKPS1 TxCKPS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 Unimplemented: Read as ‘0’ bit 6-3 TxOUTPS: Timerx Output Postscale Select bits 0000 = 1:1 Postscale 0001 = 1:2 Postscale • • • 1111 = 1:16 Postscale bit 2 TMRxON: Timerx On bit 1 = Timerx is on 0 = Timerx is off bit 1-0 TxCKPS: Timerx Clock Prescale Select bits 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16 16.2 Timer2/4/6/8 Interrupt 16.3 The Timer2/4/6/8 modules have 8-bit Period registers, PRx, that are both readable and writable. Timer2/4/6/8 increment from 00h until they match PR2/4/6/8 and then reset to 00h on the next increment cycle. The PRx registers are initialized to FFh upon Reset. FIGURE 16-1: TIMER2/4/6/8 BLOCK DIAGRAM 4 1:1 to 1:16 Postscaler Set TMRxIF 2 TMRx Output (to PWM) Reset FOSC/4 Output of TMRx The outputs of TMRx (before the postscaler) are used only as a PWM time base for the ECCP modules. They are not used as baud rate clocks for the MSSPx modules as is the Timer2 output. TxOUTPS TxCKPS x = Bit is unknown 1:1, 1:4, 1:16 Prescaler TMRx 8 TMRx/PRx Match Comparator 8 PRx 8 Internal Data Bus DS30000575C-page 294  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 17.0 REAL-TIME CLOCK AND CALENDAR (RTCC) The key features of the Real-Time Clock and Calendar (RTCC) module are: • Hardware Real-Time Clock and Calendar (RTCC) • Provides hours, minutes and seconds using 24- hour format • Visibility of one-half second period • Provides calendar – weekday, date, month and year • Alarm configurable for half a second, one second, 10 seconds, one minute, 10 minutes, one hour, one day, one week or one month • Alarm repeat with decrementing counter • Alarm with indefinite repeat – chime • Year 2000 to 2099 leap year correction • BCD format for smaller software overhead • Optimized for long term battery operation • Fractional second synchronization • Multiple clock sources - SOSC - LPRC - 50 Hz - 60 Hz • User calibration of the 32.768 kHz clock crystal frequency with periodic auto-adjust • Calibration to within ±2.64 seconds error per month • Calibrates up to 260 ppm of crystal error The RTCC module is intended for applications where accurate time must be maintained for an extended period with minimum to no intervention from the CPU. The module is optimized for low-power usage in order to provide extended battery life, while keeping track of time. The module is a 100-year clock and calendar with automatic leap year detection. The range of the clock is from 00:00:00 (midnight) on January 1, 2000 to 23:59:59 on December 31, 2099. Hours are measured in 24-hour (military time) format. The clock provides a granularity of one second with half-second visibility to the user. FIGURE 17-1: RTCC BLOCK DIAGRAM RTCC Clock Domain 32.768 kHz Input from SOSC Oscillator CPU Clock Domain RTCCON1 RTCC Prescalers Internal RC (LF-INTOSC) ALRMRPT YEAR 0.5s MTHDY RTCC Timer Alarm Event RTCVALx WKDYHR MINSEC Comparator ALMTHDY Compare Registers with Masks ALRMVALx ALWDHR ALMINSEC Repeat Counter RTCC Interrupt RTCC Interrupt Logic Alarm Pulse RTCC Pin RTCOE  2012-2016 Microchip Technology Inc. DS30000575C-page 295 PIC18F97J94 FAMILY 17.1 RTCC MODULE REGISTERS The RTCC module registers are divided into the following categories: RTCC Control Registers • • • • • • RTCCON1 RTCCON2 RTCCAL PADCFG ALRMCFG ALRMRPT RTCC Value Registers • RTCVALH • RTCVALL Both registers access the following registers: - YEAR - MONTH - DAY - WEEKDAY - HOUR - MINUTE - SECOND DS30000575C-page 296 Alarm Value Registers • ALRMVALH • ALRMVALL Both registers access the following registers: - ALRMMNTH - ALRMDAY - ALRMWD - ALRMHR - ALRMMIN - ALRMSEC Note: The RTCVALH and RTCVALL registers can be accessed through RTCRPT (RTCCON1). ALRMVALH and ALRMVALL can be accessed through ALRMPTR (ALRMCFG).  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 17.1.1 RTCC CONTROL REGISTERS REGISTER 17-1: R/W-0 RTCCON1: RTCC CONFIGURATION REGISTER 1(1) U-0 RTCEN(2) — R/W-0 R-0 (4) RTCWREN R-0 (3) RTCSYNC HALFSEC R/W-0 R/W-0 R/W-0 RTCOE RTCPTR1 RTCPTR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 RTCEN: RTCC Enable bit(2) 1 = RTCC module is enabled 0 = RTCC module is disabled bit 6 Unimplemented: Read as ‘0’ bit 5 RTCWREN: RTCC Value Registers Write Enable bit(4) 1 = RTCVALH, RTCVALL and RTCCON2 registers can be written to by the user 0 = RTCVALH, RTCVALL and RTCCON2 registers are locked out from being written to by the user bit 4 RTCSYNC: RTCC Value Registers Read Synchronization bit 1 = RTCVALH, RTCVALL and ALRMRPT registers can change while reading if a rollover ripple results in an invalid data read. If the register is read twice and results in the same data, the data can be assumed to be valid. 0 = RTCVALH, RTCVALL or ALRMRPT registers can be read without concern over a rollover ripple bit 3 HALFSEC: Half-Second Status bit(3) 1 = Second half period of a second 0 = First half period of a second bit 2 RTCOE: RTCC Output Enable bit 1 = RTCC clock output is enabled 0 = RTCC clock output is disabled bit 1-0 RTCPTR: RTCC Value Register Window Pointer bits Points to the corresponding RTCC Value registers when reading the RTCVALH and RTCVALL registers. The RTCPTR value decrements on every read or write of RTCVALH until it reaches ‘00’. RTCVALH: 00 = Minutes 01 = Weekday 10 = Month 11 = Reserved RTCVALL: 00 = Seconds 01 = Hours 10 = Day 11 = Year Note 1: 2: 3: 4: The RTCCON1 register is only affected by a POR. A write to the RTCEN bit is only allowed when RTCWREN = 1. This bit is read-only; it is cleared to ‘0’ on a write to the lower half of the MINSEC register. RTCWREN can only be written with the unlock sequence (see Example 17-1).  2012-2016 Microchip Technology Inc. DS30000575C-page 297 PIC18F97J94 FAMILY REGISTER 17-2: RTCCAL: RTCC CALIBRATION REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CAL7 CAL6 CAL5 CAL4 CAL3 CAL2 CAL1 CAL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 x = Bit is unknown CAL: RTC Drift Calibration bits 01111111 = Maximum positive adjustment; adds 508 RTC clock pulses every minute . . . 00000001 = Minimum positive adjustment; adds four RTC clock pulses every minute 00000000 = No adjustment 11111111 = Minimum negative adjustment; subtracts four RTC clock pulses every minute . . . 10000000 = Maximum negative adjustment; subtracts 512 RTC clock pulses every minute DS30000575C-page 298  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY Register 17-3: R/W-0 R/W-0 RTCCON2: RTC CONFIGURATION REGISTER 2(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PWCEN(1) PWCPOL(1) PWCCPRE(1) PWCSPRE(1) RTCCLKSEL1 RTCCLKSEL0 RTCSECSEL1 RTCSECSEL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 PWCEN: Power Control Enable bit(1) 1 = Power control is enabled 0 = Power control is disabled bit 6 PWCPOL: Power Control Polarity bit(1) 1 = Power control output is active-high 0 = Power control output is active-low bit 5 PWCCPRE: Power Control/Stability Prescaler bits(1) 1 = PWC stability window clock is divide-by-2 of source RTCC clock 0 = PWC stability window clock is divide-by-1 of source RTCC clock bit 4 PWCSPRE: Power Control Sample Prescaler bits(1) 01 =PWC sample window clock is divide-by-2 of source RTCC clock 00 =PWC sample window clock is divide-by-1 of source RTCC clock bit 3-2 RTCCLKSEL: RTCC Clock Select bits Determines the source of the internal RTCC clock, which is used for all RTCC timer operations. 11 =60 Hz Powerline 10 =50 Hz Powerline 01 =INTOSC 00 =SOSC bit 1-0 RTSECSEL: RTCC Seconds Clock Output Select bit 11 =Power control 10 =RTCC source clock is selected for the RTCC pin (pin can be LF-INTOSC or SOSC, depending on the RTCOSC (CONFIG3L) bit setting 01 =RTCC seconds clock is selected for the RTCC pin 00 =RTCC alarm pulse is selected for the RTCC pin Note 1: The RTCCON2 register is only affected by a POR.  2012-2016 Microchip Technology Inc. DS30000575C-page 299 PIC18F97J94 FAMILY REGISTER 17-4: ALRMCFG: ALARM CONFIGURATION REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ALRMEN CHIME AMASK3 AMASK2 AMASK1 AMASK0 ALRMPTR1 ALRMPTR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 ALRMEN: Alarm Enable bit 1 = Alarm is enabled (cleared automatically after an alarm event whenever ARPT = 00h and CHIME = 0) 0 = Alarm is disabled bit 6 CHIME: Chime Enable bit 1 = Chime is enabled; ARPT bits are allowed to roll over from 00h to FFh 0 = Chime is disabled; ARPT bits stop once they reach 00h bit 5-2 AMASK: Alarm Mask Configuration bits 0000 = Every half second 0001 = Every second 0010 = Every 10 seconds 0011 = Every minute 0100 = Every 10 minutes 0101 = Every hour 0110 = Once a day 0111 = Once a week 1000 = Once a month 1001 = Once a year (except when configured for February 29th, once every four years) 101x = Reserved – Do not use 11xx = Reserved – Do not use bit 1-0 ALRMPTR: Alarm Value Register Window Pointer bits Points to the corresponding Alarm Value registers when reading the ALRMVALH and ALRMVALL registers. The ALRMPTR value decrements on every read or write of ALRMVALH until it reaches ‘00’. ALRMVALH: 00 = ALRMMIN 01 = ALRMWD 10 = ALRMMNTH 11 = Unimplemented ALRMVALL: 00 = ALRMSEC 01 = ALRMHR 10 = ALRMDAY 11 = Unimplemented DS30000575C-page 300  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 17-5: ALRMRPT: ALARM REPEAT REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ARPT7 ARPT6 ARPT5 ARPT4 ARPT3 ARPT2 ARPT1 ARPT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 17.1.2 x = Bit is unknown ARPT: Alarm Repeat Counter Value bits 11111111 = Alarm will repeat 255 more times . . . 00000000 = Alarm will not repeat The counter decrements on any alarm event. The counter is prevented from rolling over from 00h to FFh unless CHIME = 1. RTCVALH AND RTCVALL REGISTER MAPPINGS The registers described in this section are the targets or sources for writes or reads to the RTCVALH and RTCVALL in the order they will appear when accessed through the RTCCON1 pointer. For more information on RTCVAL register mapping, see Section 17.2.8 “Register Mapping”. REGISTER 17-6: RESERVED REGISTER (RTCVALH when RTCPTR = 11) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 Note: x = Bit is unknown Unimplemented: Read as ‘0’ A read or write to the RTCVALH register when RTCPTR = 11 is necessary to automatically decrement RTCPTR.  2012-2016 Microchip Technology Inc. DS30000575C-page 301 PIC18F97J94 FAMILY YEAR: YEAR VALUE REGISTER(1) (RTCVALL when RTCPTR = 11) REGISTER 17-7: R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x YRTEN3 YRTEN2 YRTEN1 YRTEN0 YRONE3 YRONE2 YRONE1 YRONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-4 YRTEN: Binary Coded Decimal Value of Year’s Tens Digit bits Contains a value from 0 to 9. bit 3-0 YRONE: Binary Coded Decimal Value of Year’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to the YEAR register is only allowed when RTCWREN = 1. MONTH: MONTH VALUE REGISTER(1) (RTCVALH when RTCPTR = 10) REGISTER 17-8: U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x — — — MTHTEN0 MTHONE3 MTHONE2 MTHONE1 MTHONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-5 Unimplemented: Read as ‘0’ bit 4 MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bit Contains a value of 0 or 1. bit 3-0 MTHONE: Binary Coded Decimal Value of Month’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN = 1. DS30000575C-page 302  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 17-9: DAY: DAY VALUE REGISTER(1) (RTCVALL when RTCPTR = 10) U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — DAYTEN1 DAYTEN0 DAYONE3 DAYONE2 DAYONE1 DAYONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 DAYTEN: Binary Coded Decimal value of Day’s Tens Digit bits Contains a value from 0 to 3. bit 3-0 DAYONE: Binary Coded Decimal Value of Day’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN = 1. REGISTER 17-10: WEEKDAY: WEEKDAY VALUE REGISTER(1) (RTCVALH when RTCPTR = 01) U-0 U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x — — — — — WDAY2 WDAY1 WDAY0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-3 Unimplemented: Read as ‘0’ bit 2-0 WDAY: Binary Coded Decimal Value of Weekday Digit bits Contains a value from 0 to 6. Note 1: A write to this register is only allowed when RTCWREN = 1. REGISTER 17-11: HOUR: HOUR VALUE REGISTER(1) (RTCVALL when RTCPTR = 01) U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — HRTEN1 HRTEN0 HRONE3 HRONE2 HRONE1 HRONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 HRTEN: Binary Coded Decimal Value of Hour’s Tens Digit bits Contains a value from 0 to 2. bit 3-0 HRONE: Binary Coded Decimal Value of Hour’s Ones Digit bits Contains a value from 0 to 9. Note 1: x = Bit is unknown A write to this register is only allowed when RTCWREN = 1.  2012-2016 Microchip Technology Inc. DS30000575C-page 303 PIC18F97J94 FAMILY REGISTER 17-12: MINUTE: MINUTE VALUE REGISTER (RTCVALH when RTCPTR = 00) U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — MINTEN2 MINTEN1 MINTEN0 MINONE3 MINONE2 MINONE1 MINONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 Unimplemented: Read as ‘0’ bit 6-4 MINTEN: Binary Coded Decimal Value of Minute’s Tens Digit bits Contains a value from 0 to 5. bit 3-0 MINONE: Binary Coded Decimal Value of Minute’s Ones Digit bits Contains a value from 0 to 9. REGISTER 17-13: SECOND: SECOND VALUE REGISTER (RTCVALL when RTCPTR = 00) U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — SECTEN2 SECTEN1 SECTEN0 SECONE3 SECONE2 SECONE1 SECONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 Unimplemented: Read as ‘0’ bit 6-4 SECTEN: Binary Coded Decimal Value of Second’s Tens Digit bits Contains a value from 0 to 5. bit 3-0 SECONE: Binary Coded Decimal Value of Second’s Ones Digit bits Contains a value from 0 to 9. DS30000575C-page 304  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 17.1.3 ALRMVALH AND ALRMVALL REGISTER MAPPINGS The registers described in this section are the targets or sources for writes or reads to the ALRMVALH and ALRMVALL in the order they will appear when accessed through the ALRMCFG pointer. For more information on ALRMVAL register mapping, see Section 17.2.8 “Register Mapping”. REGISTER 17-14: ALRMMNTH: ALARM MONTH VALUE REGISTER(1) (ALRMVALH when ALRMPTR = 10) U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x — — — MTHTEN0 MTHONE3 MTHONE2 MTHONE1 MTHONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-5 Unimplemented: Read as ‘0’ bit 4 MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bits Contains a value of 0 or 1. bit 3-0 MTHONE: Binary Coded Decimal Value of Month’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN = 1. REGISTER 17-15: ALRMDAY: ALARM DAY VALUE REGISTER(1) (ALRMVALL when ALRMPTR = 10) U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — DAYTEN1 DAYTEN0 DAYONE3 DAYONE2 DAYONE1 DAYONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 DAYTEN: Binary Coded Decimal Value of Day’s Tens Digit bits Contains a value from 0 to 3. bit 3-0 DAYONE: Binary Coded Decimal Value of Day’s Ones Digit bits Contains a value from 0 to 9. Note 1: x = Bit is unknown A write to this register is only allowed when RTCWREN = 1.  2012-2016 Microchip Technology Inc. DS30000575C-page 305 PIC18F97J94 FAMILY REGISTER 17-16: ALRMWD: ALARM WEEKDAY VALUE REGISTER(1) (ALRMVALH WHEN ALRMPTR = 01) U-0 U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x — — — — — WDAY2 WDAY1 WDAY0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-3 Unimplemented: Read as ‘0’ bit 2-0 WDAY: Binary Coded Decimal Value of Weekday Digit bits Contains a value from 0 to 6. Note 1: A write to this register is only allowed when RTCWREN = 1. REGISTER 17-17: ALRMHR: ALARM HOURS VALUE REGISTER(1) (ALRMVALL when ALRMPTR = 01) U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — HRTEN1 HRTEN0 HRONE3 HRONE2 HRONE1 HRONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 HRTEN: Binary Coded Decimal Value of Hour’s Tens Digit bits Contains a value from 0 to 2. bit 3-0 HRONE: Binary Coded Decimal Value of Hour’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN = 1. DS30000575C-page 306  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 17-18: ALRMMIN: ALARM MINUTES VALUE REGISTER (ALRMVALH when ALRMPTR = 00) U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — MINTEN2 MINTEN1 MINTEN0 MINONE3 MINONE2 MINONE1 MINONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 Unimplemented: Read as ‘0’ bit 6-4 MINTEN: Binary Coded Decimal Value of Minute’s Tens Digit bits Contains a value from 0 to 5. bit 3-0 MINONE: Binary Coded Decimal Value of Minute’s Ones Digit bits Contains a value from 0 to 9. REGISTER 17-19: ALRMSEC: ALARM SECONDS VALUE REGISTER (ALRMVALL when ALRMPTR = 00) U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — SECTEN2 SECTEN1 SECTEN0 SECONE3 SECONE2 SECONE1 SECONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 Unimplemented: Read as ‘0’ bit 6-4 SECTEN: Binary Coded Decimal Value of Second’s Tens Digit bits Contains a value from 0 to 5. bit 3-0 SECONE: Binary Coded Decimal Value of Second’s Ones Digit bits Contains a value from 0 to 9.  2012-2016 Microchip Technology Inc. DS30000575C-page 307 PIC18F97J94 FAMILY 17.1.4 17.2 RTCEN BIT WRITE RTCWREN (RTCCON1) must be set before a write to RTCEN can take place. Any write to the RTCEN bit, while RTCWREN = 0, will be ignored. Like the RTCEN bit, the RTCVALH and RTCVALL registers can only be written to when RTCWREN = 1. A write to these registers, while RTCWREN = 0, will be ignored. FIGURE 17-2: 17.2.1 Operation REGISTER INTERFACE The register interface for the RTCC and alarm values is implemented using the Binary Coded Decimal (BCD) format. This simplifies the firmware when using the module, as each of the digits is contained within its own 4-bit value (see Figure 17-2 and Figure 17-3). TIMER DIGIT FORMAT Year 0-9 0-9 0-1 Hours (24-hour format) 0-2 FIGURE 17-3: Day Month 0-9 0-9 0-3 Minutes 0-5 0-9 0-5 0-9 0-6 1/2 Second Bit (binary format) 0/1 ALARM DIGIT FORMAT 0-1 Hours (24-hour format) DS30000575C-page 308 0-9 Seconds Day Month 0-2 Day of Week 0-9 0-9 0-3 Minutes 0-5 Day of Week 0-9 0-6 Seconds 0-9 0-5 0-9  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 17.2.2 CLOCK SOURCE Calibration of the crystal can be done through this module to yield an error of 3 seconds or less per month. (For further details, see Section 17.2.9 “Calibration”.) As mentioned earlier, the RTCC module is intended to be clocked by an external Real-Time Clock (RTC) crystal, oscillating at 32.768 kHz, but an internal oscillator can be used. The RTCC clock selection is decided by the RTCOSC bit (CONFIG3L). FIGURE 17-4: CLOCK SOURCE MULTIPLEXING 32.768 kHz XTAL from SOSC 1:16384 Half-Second Clock Half Second(1) Clock Prescaler(1) Internal RC One Second Clock RTCCON1 Second Note 1: 17.2.2.1 Hour:Minute Day Month Day of Week Writing to the lower half of the MINSEC register resets all counters, allowing fraction of a second synchronization; clock prescaler is held in Reset when RTCEN = 0. Real-Time Clock Enable TABLE 17-1: The RTCC module can be clocked by an external, 32.768 kHz crystal (SOSC Oscillator) or the LF-INTOSC Oscillator, which can be selected in CONFIG3L. DIGIT CARRY RULES This section explains which timer values are affected when there is a rollover: • Time of Day: From 23:59:59 to 00:00:00 with a carry to the Day field • Month: From 12/31 to 01/01 with a carry to the Year field • Day of Week: From 6 to 0 with no carry (see Table 17-1) • Year Carry: From 99 to 00; this also surpasses the use of the RTCC DAY OF WEEK SCHEDULE Day of Week If the external clock is used, the SOSC Oscillator should be enabled. If LF-INTOSC is providing the clock, the INTOSC clock can be brought out to the RTCC pin by the RTSECSEL bits (RTCCON2). 17.2.3 Year Sunday 0 Monday 1 Tuesday 2 Wednesday 3 Thursday 4 Friday 5 Saturday 6 TABLE 17-2: DAY TO MONTH ROLLOVER SCHEDULE Month Maximum Day Field 01 (January) 31 02 (February) 28 or 29(1) 03 (March) 31 04 (April) 30 For the day-to-month rollover schedule, see Table 17-2. 05 (May) 31 Because the following values are in BCD format, the carry to the upper BCD digit occurs at the count of 10, not 16 (SECONDS, MINUTES, HOURS, WEEKDAY, DAYS and MONTHS). 06 (June) 30 07 (July) 31 08 (August) 31 09 (September) 30 10 (October) 31 11 (November) 30 12 (December) 31 Note 1:  2012-2016 Microchip Technology Inc. See Section 17.2.4 “Leap Year”. DS30000575C-page 309 PIC18F97J94 FAMILY 17.2.4 LEAP YEAR Since the year range on the RTCC module is 2000 to 2099, the leap year calculation is determined by any year divisible by four in the above range. Only February is affected in a leap year. February will have 29 days in a leap year and 28 days in any other year. 17.2.5 GENERAL FUNCTIONALITY All Timer registers containing a time value of seconds or greater are writable. The user configures the time by writing the required year, month, day, hour, minutes and seconds to the Timer registers, via register pointers. (See Section 17.2.8 “Register Mapping”.) The timer uses the newly written values and proceeds with the count from the required starting point. The RTCC is enabled by setting the RTCEN bit (RTCCON1). If enabled, while adjusting these registers, the timer still continues to increment. However, any time the MINSEC register is written to, both of the timer prescalers are reset to ‘0’. This allows fraction of a second synchronization. The Timer registers are updated in the same cycle as the WRITE instruction’s execution by the CPU. The user must ensure that when RTCEN = 1, the updated registers will not be incremented at the same time. This can be accomplished in several ways: • By checking the RTCSYNC bit (RTCCON1) • By checking the preceding digits from which a carry can occur • By updating the registers immediately following the seconds pulse (or an alarm interrupt) The user has visibility to the half-second field of the counter. This value is read-only and can be reset only by writing to the lower half of the SECONDS register. 17.2.6 SAFETY WINDOW FOR REGISTER READS AND WRITES The RTCSYNC bit indicates a time window during which the RTCC clock domain registers can be safely read and written without concern about a rollover. When RTCSYNC = 0, the registers can be safely accessed by the CPU. Whether RTCSYNC = 1 or 0, the user should employ a firmware solution to ensure that the data read did not fall on a rollover boundary, resulting in an invalid or partial read. This firmware solution would consist of reading each register twice and then comparing the two values. If the two values matched, then a rollover did not occur. DS30000575C-page 310 17.2.7 WRITE LOCK In order to perform a write to any of the RTCC Timer registers, the RTCWREN bit (RTCCON1) must be set. To avoid accidental writes to the RTCC Timer register, it is recommended that the RTCWREN bit (RTCCON1) be kept clear when not writing to the register. For the RTCWREN bit to be set, there is only one instruction cycle time window allowed between the 55h/AA sequence and the setting of RTCWREN. For that reason, it is recommended that users follow the code example in Example 17-1. EXAMPLE 17-1: movlw movwf movlw movwf bsf 17.2.8 SETTING THE RTCWREN BIT 0x55 EECON2 0xAA EECON2 RTCCON1,RTCWREN REGISTER MAPPING To limit the register interface, the RTCC Timer and Alarm Timer registers are accessed through corresponding register pointers. The RTCC Value register window (RTCVALH and RTCVALL) uses the RTCPTRx bits (RTCCON1) to select the required Timer register pair. By reading or writing to the RTCVALH register, the RTCC Pointer value (RTCPTR) decrements by ‘1’ until it reaches ‘00’. When ‘00’ is reached, the MINUTES and SECONDS value is accessible through RTCVALH and RTCVALL until the pointer value is manually changed. TABLE 17-3: RTCPTR RTCVALH AND RTCVALL REGISTER MAPPING RTCC Value Register Window RTCVALH RTCVALL 00 MINUTES SECONDS 01 WEEKDAY HOURS 10 MONTH DAY 11 — YEAR The Alarm Value register windows (ALRMVALH and ALRMVALL) use the ALRMPTR bits (ALRMCFG) to select the desired Alarm register pair. By reading or writing to the ALRMVALH register, the Alarm Pointer value, ALRMPTR, decrements by ‘1’ until it reaches ‘00’. When it reaches ‘00’, the ALRMMIN and ALRMSEC values are accessible through ALRMVALH and ALRMVALL until the pointer value is manually changed.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 17-4: 17.3 ALRMVAL REGISTER MAPPING ALRMPTR 00 The Alarm features and characteristics are: Alarm Value Register Window ALRMVALH ALRMVALL ALRMMIN ALRMSEC 01 ALRMWD ALRMHR 10 ALRMMNTH ALRMDAY 11 — — 17.2.9 CALIBRATION The real-time crystal input can be calibrated using the periodic auto-adjust feature. When properly calibrated, the RTCC can provide an error of less than three seconds per month. To perform this calibration, find the number of error clock pulses and store the value into the lower half of the RTCCAL register. The 8-bit signed value, loaded into RTCCAL, is multiplied by four and will either be added or subtracted from the RTCC timer, once every minute. To calibrate the RTCC module: 1. 2. Use another timer resource on the device to find the error of the 32.768 kHz crystal. Convert the number of error clock pulses per minute (see Equation 17-1). EQUATION 17-1: CONVERTING ERROR CLOCK PULSES (Ideal Frequency (32,758) – Measured Frequency) * 60 = Error Clocks per Minute 3. Alarm • Configurable from half a second to one year • Enabled using the ALRMEN bit (ALRMCFG, Register 17-4) • Offers one-time and repeat alarm options 17.3.1 CONFIGURING THE ALARM The alarm feature is enabled using the ALRMEN bit. This bit is cleared when an alarm is issued. The bit will not be cleared if the CHIME bit = 1 or if ALRMRPT  0. The interval selection of the alarm is configured through the ALRMCFG bits (AMASK); see Figure 17-5. These bits determine which and how many digits of the alarm must match the clock value for the alarm to occur. The alarm can also be configured to repeat based on a preconfigured interval. The number of times this occurs, after the alarm is enabled, is stored in the ALRMRPT register. Note: While the alarm is enabled (ALRMEN = 1), changing any of the registers, other than the RTCCAL, ALRMCFG and ALRMRPT registers and the CHIME bit, can result in a false alarm event leading to a false alarm interrupt. To avoid this, only change the timer and alarm values while the alarm is disabled (ALRMEN = 0). It is recommended that the ALRMCFG and ALRMRPT registers and CHIME bit be changed when RTCSYNC = 0. • If the oscillator is faster than ideal (negative result from Step 2), the RCFGCALL register value needs to be negative. This causes the specified number of clock pulses to be subtracted from the timer counter once every minute. • If the oscillator is slower than ideal (positive result from Step 2), the RCFGCALL register value needs to be positive. This causes the specified number of clock pulses to be added to the timer counter once every minute. Load the RTCCAL register with the correct value. Writes to the RTCCAL register should occur only when the timer is turned off or immediately after the rising edge of the seconds pulse. Note: In determining the crystal’s error value, it is the user’s responsibility to include the crystal’s initial error from drift due to temperature or crystal aging.  2012-2016 Microchip Technology Inc. DS30000575C-page 311 PIC18F97J94 FAMILY FIGURE 17-5: ALARM MASK SETTINGS Alarm Mask Setting AMASK Day of the Week Month Day Hours Minutes Seconds 0000 – Every half second 0001 – Every second 0010 – Every 10 seconds s 0011 – Every minute s s m s s m m s s 0100 – Every 10 minutes 0101 – Every hour 0110 – Every day 0111 – Every week d 1000 – Every month 1001 – Every year(1) Note 1: m m h h m m s s h h m m s s d d h h m m s s d d h h m m s s Annually, except when configured for February 29. When ALRMCFG = 00 and the CHIME bit = 0 (ALRMCFG), the repeat function is disabled and only a single alarm will occur. The alarm can be repeated up to 255 times by loading the ALRMRPT register with FFh. After each alarm is issued, the ALRMRPT register is decremented by one. Once the register has reached ‘00’, the alarm will be issued one last time. After the alarm is issued a last time, the ALRMEN bit is cleared automatically and the alarm turned off. Indefinite repetition of the alarm can occur if the CHIME bit = 1. When CHIME = 1, the alarm is not disabled when the ALRMRPT register reaches ‘00’, but it rolls over to FF and continues counting indefinitely. 17.3.2 ALARM INTERRUPT At every alarm event, an interrupt is generated. Additionally, an alarm pulse output is provided that operates at half the frequency of the alarm. The alarm pulse output is completely synchronous with the RTCC clock and can be used as a trigger clock to other peripherals. This output is available on the RTCC pin. The output pulse is a clock with a 50% duty cycle and a frequency half that of the alarm event (see Figure 17-6). The RTCC pin can also output the seconds clock. The user can select between the alarm pulse, generated by the RTCC module, or the seconds clock output. The RTSECSEL bits (RTCCON2) select between these two outputs: • Alarm pulse – RTSECSEL = 00 • Seconds clock – RTSECSEL = 01 DS30000575C-page 312  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 17-6: TIMER PULSE GENERATION RTCEN bit ALRMEN bit RTCC Alarm Event RTCC Pin 17.4 Sleep Mode 17.5.2 POWER-ON RESET (POR) The timer and alarm continue to operate while in Sleep mode. The operation of the alarm is not affected by Sleep, as an alarm event can always wake-up the CPU. The RTCCON1 and ALRMRPT registers are reset only on a POR. Once the device exits the POR state, the clock registers should be reloaded with the desired values. The Idle mode does not affect the operation of the timer or alarm. The timer prescaler values can be reset only by writing to the SECONDS register. No device Reset can affect the prescalers. 17.5 17.5.1 Reset DEVICE RESET When a device Reset occurs, the ALRMRPT register is forced to its Reset state, causing the alarm to be disabled (if enabled prior to the Reset). If the RTCC was enabled, it will continue to operate when a basic device Reset occurs.  2012-2016 Microchip Technology Inc. DS30000575C-page 313 PIC18F97J94 FAMILY 17.6 Register Maps Table 17-5, Table 17-6 and Table 17-7 summarize the registers associated with the RTCC module. TABLE 17-5: File Name RTCC CONTROL REGISTERS Bit 7 RTCCON1 RTCEN RTCCAL CAL7 Bit 6 Bit 5 — Bit 4 RTCWREN RTCSYNC CAL6 CAL5 Bit 3 Bit 2 Bit 1 Bit 0 HALFSEC RTCOE RTCPTR1 RTCPTR0 CAL3 CAL2 CAL1 CAL0 CAL4 RTCCON2 PWCEN PWCPOL PWCCPRE PWCSPRE RTCCLKSEL1 RTCCLKSEL0 RTCSECSEL1 RTCSECSEL ALRMCFG ALRMEN CHIME ALRMRPT ARPT7 ARPT6 PMD3 DSMMD CTMUMD Legend: AMASK3 AMASK2 AMASK1 AMASK0 ALRMPTR1 ALRMPTR0 ARPT5 ARPT4 ARPT3 ARPT2 ARPT1 ARPT0 ADCMD RTCCMD LCDMD PSPMD REFO1MD REFO2MD — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal for 80-pin devices. TABLE 17-6: File Name RTCC VALUE REGISTERS Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 RTCVALH RTCC Value High Register Window based on RTCPTR RTCVALL RTCC Value Low Register Window based on RTCPTR TABLE 17-7: File Name Bit 0 ALARM VALUE REGISTERS Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 ALRMVALH Alarm Value High Register Window based on ALRMPTR ALRMVALL Alarm Value Low Register Window based on ALRMPTR DS30000575C-page 314 Bit 0  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 18.0 ENHANCED CAPTURE/ COMPARE/PWM (ECCP) MODULE PIC18FXXJ94 devices have three Enhanced Capture/ Compare/PWM (ECCP) modules: ECCP1, ECCP2 and ECCP3. These modules contain a 16-bit register, which can operate as a 16-bit Capture register, a 16-bit Compare register or a PWM Master/Slave Duty Cycle register. These ECCP modules are upward compatible with CCP Note: Throughout this section, generic references are used for register and bit names that are the same, except for an ‘x’ variable that indicates the item’s association with the CCP1, CCP2 or CCP3 module. For example, the control register is named CCPxCON and refers to CCP1CON, CCP2CON and CCP3CON.  2012-2016 Microchip Technology Inc. ECCP1, ECCP2 and ECCP3 are implemented as standard CCP modules with enhanced PWM capabilities. These include: • • • • • Provision for two or four output channels Output Steering modes Programmable polarity Programmable dead-band control Automatic shutdown and restart The enhanced features are discussed in detail in Section 18.4 “PWM (Enhanced Mode)”. The ECCP1, ECCP2 and ECCP3 modules use the ECCP Control registers, CCP1CON, CCP2CON and CCP3CON. The control registers, CCP4CON through CCP10CON, are for the modules, CCP4 through CCP10. DS30000575C-page 315 PIC18F97J94 FAMILY REGISTER 18-1: R/W-0 PxM1 CCPxCON: ENHANCED CAPTURE/COMPARE/PWM x CONTROL R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PxM0 DCxB1 DCxB0 CCPxM3 CCPxM2 CCPxM1 CCPxM0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 PxM: Enhanced PWM Output Configuration bits If CCPxM = 00, 01, 10: xx =PxA is assigned as the capture/compare input/output; PxB, PxC and PxD are assigned as port pins If CCPxM = 11: 00 =Single output: PxA, PxB, PxC and PxD are controlled by steering (see Section 18.4.7 “Pulse Steering Mode”) 01 =Full-bridge output forward: PxD is modulated; PxA is active; PxB, PxC are inactive 10 =Half-bridge output: PxA, PxB are modulated with dead-band control; PxC and PxD are assigned as port pins 11 =Full-bridge output reverse: PxB is modulated; PxC is active; PxA and PxD are inactive bit 5-4 DCxB: PWM Duty Cycle bit Capture mode: Unused. Compare mode: Unused. PWM mode: These bits are the two LSbs of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are found in CCPRxL. bit 3-0 CCPxM: CCPx Mode Select bits 0000 = Capture/Compare/PWM off (resets ECCPx module) 0001 = Reserved 0010 = Compare mode: Toggle output on match 0011 = Reserved 0100 = Capture mode: Every falling edge 0101 = Capture mode: Every rising edge 0110 = Capture mode: Every fourth rising edge 0111 = Capture mode: Every 16th rising edge 1000 = Compare mode: Initialize ECCPx pin low, set output on compare match (set CCPxIF) 1001 = Compare mode: Initialize ECCPx pin high, clear output on compare match (set CCPxIF) 1010 = Compare mode: Generate software interrupt only, ECCPx pin reverts to I/O state 1011 = Compare mode: Trigger special event (ECCPx resets TMR1 or TMR3, starts A/D conversion, sets CCPxIF bit) 1100 = PWM mode: PxA and PxC are active-high; PxB and PxD are active-high 1101 = PWM mode: PxA and PxC are active-high; PxB and PxD are active-low 1110 = PWM mode: PxA and PxC are active-low; PxB and PxD are active-high 1111 = PWM mode: PxA and PxC are active-low; PxB and PxD are active-low DS30000575C-page 316  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 18-2: CCPTMRS0: CCP TIMER SELECT 0 REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 C3TSEL1 C3TSEL0 C2TSEL2 C2TSEL1 C2TSEL0 C1TSEL2 C1TSEL1 C1TSEL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-6 C3TSEL: CCP3 Timer Selection bits 00 = CCP3 is based off of TMR1/TMR2 01 = CCP3 is based off of TMR3/TMR4 10 = CCP3 is based off of TMR3/TMR6 11 = CCP3 is based off of TMR3/TMR8 bit 5-3 C2TSEL: CCP2 Timer Selection bits 000 = CCP2 is based off of TMR1/TMR2 001 = CCP2 is based off of TMR3/TMR4 010 = CCP2 is based off of TMR3/TMR6 011 = CCP2 is based off of TMR3/TMR8 100 = Reserved; do not use 101 = Reserved; do not use 110 = Reserved; do not use 111 = Reserved; do not use bit 2-0 C1TSEL: CCP1 Timer Selection bits 000 = CCP1 is based off of TMR1/TMR2 001 = CCP1 is based off of TMR3/TMR4 010 = CCP1 is based off of TMR3/TMR6 011 = CCP1 is based off of TMR3/TMR8 100 = Reserved; do not use 101 = Reserved; do not use 110 = Reserved; do not use 111 = Reserved; do not use  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 317 PIC18F97J94 FAMILY In addition to the expanded range of modes available through the CCPxCON, the ECCP modules have three additional registers associated with Enhanced PWM operation, Pulse Steering Control and auto-shutdown features. They are: • ECCPxDEL – Enhanced PWM x Control • PSTRxCON – Pulse Steering x Control • ECCPxAS – Auto-Shutdown x Control 18.1 ECCP Outputs and Configuration The Enhanced CCP module may have up to four PWM outputs, depending on the selected operating mode. These outputs, designated as PxA through PxD, are routed through the PPS-Lite module. Therefore, individual functions can be mapped to any of the remappable I/ O pins (RPn). The outputs that are active depend on the ECCP operating mode selected. The pin assignments are summarized in Table 18-3. To configure the I/O pins as PWM outputs, the proper PWM mode must be selected by setting the PxM and CCPxM bits. The appropriate TRIS direction bits for the port pins must also be set as outputs Table 18-3. DS30000575C-page 318 18.1.1 ECCP MODULE AND TIMER RESOURCES The ECCP modules use Timers, 1, 2, 3, 4, 6 or 8, depending on the mode selected. These timers are available to CCP modules in Capture, Compare or PWM modes, as shown in Table 18-1. TABLE 18-1: ECCP Mode ECCP MODE – TIMER RESOURCE Timer Resource Capture Timer1 or Timer3 Compare Timer1 or Timer3 PWM Timer2, Timer4, Timer6 or Timer8 The assignment of a particular timer to a module is determined by the timer to ECCP enable bits in the CCPTMRS0 register (Register 18-2). The interactions between the two modules are depicted in Figure 18-1. Capture operations are designed to be used when the timer is configured for Synchronous Counter mode. Capture operations may not work as expected if the associated timer is configured for Asynchronous Counter mode.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 18.2 Capture Mode 18.2.2 In Capture mode, the CCPRxH:CCPRxL register pair captures the 16-bit value of the TMR1 or TMR3 registers when an event occurs on the corresponding ECCPx pin. An event is defined as one of the following: • • • • Every falling edge Every rising edge Every fourth rising edge Every 16th rising edge TIMER1/2/3/4/5/6/8 MODE SELECTION The timers that are to be used with the capture feature (Timer1/2/3/4/5/6 or 8) must be running in Timer mode or Synchronized Counter mode. In Asynchronous Counter mode, the capture operation will not work. The timer to be used with each ECCP module is selected in the CCPTMRS0 register (Register 18-2). 18.2.3 SOFTWARE INTERRUPT The event is selected by the mode select bits, CCPxM (CCPxCON). When a capture is made, the interrupt request flag bit, CCPxIF, is set (see Table 18-2). The flag must be cleared by software. If another capture occurs before the value in the CCPRxH/L register is read, the old captured value is overwritten by the new captured value. When the Capture mode is changed, a false capture interrupt may be generated. The user should keep the CCPxIE interrupt enable bit clear to avoid false interrupts. The interrupt flag bit, CCPxIF, should also be cleared following any such change in operating mode. TABLE 18-2: There are four prescaler settings in Capture mode; they are specified as part of the operating mode selected by the mode select bits (CCPxM). Whenever the ECCP module is turned off, or Capture mode is disabled, the prescaler counter is cleared. This means that any Reset will clear the prescaler counter. ECCP1/2/3 INTERRUPT FLAG BITS ECCP Module Flag Bit 1 PIR3 2 PIR3 3 PIR4 18.2.1 ECCP PIN CONFIGURATION In Capture mode, the appropriate ECCPx pin should be configured as an input by setting the corresponding TRIS direction bit. Note: If the ECCPx pin is configured as an output, a write to the port can cause a capture condition. 18.2.4 Switching from one capture prescaler to another may generate an interrupt. Also, the prescaler counter will not be cleared; therefore, the first capture may be from a non-zero prescaler. Example 18-1 provides the recommended method for switching between capture prescalers. This example also clears the prescaler counter and will not generate the “false” interrupt. EXAMPLE 18-1: CLRF MOVLW MOVWF FIGURE 18-1: ECCP PRESCALER CHANGING BETWEEN CAPTURE PRESCALERS CCP1CON ; Turn ECCP module off NEW_CAPT_PS ; Load WREG with the ; new prescaler mode ; value and ECCP ON CCP1CON ; Load CCP1CON with ; this value CAPTURE MODE OPERATION BLOCK DIAGRAM TMR3H Set CCP1IF ECCP1 Pin Prescaler  1, 4, 16 C1TSEL0 C1TSEL1 C1TSEL2 and Edge Detect CCP1CON Q1:Q4 4 TMR3 Enable CCPR1H C1TSEL0 C1TSEL1 C1TSEL2 TMR3L CCPR1L TMR1 Enable TMR1H TMR1L 4  2012-2016 Microchip Technology Inc. DS30000575C-page 319 PIC18F97J94 FAMILY 18.3 Compare Mode 18.3.2 In Compare mode, the 16-bit CCPRx register value is constantly compared against the Timer register pair value selected in the CCPTMR0 register. When a match occurs, the ECCPx pin can be: • • • • Driven high Driven low Toggled (high-to-low or low-to-high) Unchanged (that is, reflecting the state of the I/O latch) The action on the pin is based on the value of the mode select bits (CCPxM). At the same time, the interrupt flag bit, CCPxIF, is set. 18.3.1 ECCPx PIN CONFIGURATION Users must configure the ECCPx pin as an output by clearing the appropriate TRIS bit. Note: Clearing the CCPxCON register will force the ECCPx compare output latch (depending on device configuration) to the default low level. This is not the PORTx I/O data latch. TIMER1/2/3/4/5/6/8 MODE SELECTION Timer1/2/3/4, 6 or 8, must be running in Timer mode or Synchronized Counter mode if the ECCP module is using the compare feature. In Asynchronous Counter mode, the compare operation will not work reliably. 18.3.3 SOFTWARE INTERRUPT MODE When the Generate Software Interrupt mode is chosen (CCPxM = 1010), the ECCPx pin is not affected; only the CCPxIF interrupt flag is affected. 18.3.4 SPECIAL EVENT TRIGGER The ECCP module is equipped with a Special Event Trigger. This is an internal hardware signal generated in Compare mode to trigger actions by other modules. The Special Event Trigger is enabled by selecting the Compare Special Event Trigger mode (CCPxM = 1011). The Special Event Trigger resets the Timer register pair for whichever timer resource is currently assigned as the module’s time base. This allows the CCPRx registers to serve as a programmable period register for either timer. The Special Event Trigger can also start an A/D conversion. In order to do this, the A/D Converter must already be enabled. FIGURE 18-2: COMPARE MODE OPERATION BLOCK DIAGRAM 0 TMR1H TMR1L 1 TMR3H TMR3L Special Event Trigger (Timer1/Timer3 Reset, A/D Trigger) C1TSEL0 C1TSEL1 C1TSEL2 Set CCP1IF Comparator CCPR1H CCPR1L Compare Match ECCP1 Pin Output Logic 4 S Q R TRIS Output Enable CCP1CON DS30000575C-page 320  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 18.4 PWM (Enhanced Mode) The PWM outputs are multiplexed with I/O pins and are designated: PxA, PxB, PxC and PxD. The polarity of the PWM pins is configurable and is selected by setting the CCPxM bits in the CCPxCON register appropriately. The Enhanced PWM mode can generate a PWM signal on up to four different output pins, with up to 10 bits of resolution. It can do this through four different PWM Output modes: • • • • Table 18-1 provides the pin assignments for each Enhanced PWM mode. Single PWM Half-Bridge PWM Full-Bridge PWM, Forward mode Full-Bridge PWM, Reverse mode Figure 18-3 provides an example of a simplified block diagram of the Enhanced PWM module. Note: To select an Enhanced PWM mode, the PxM bits of the CCPxCON register must be set appropriately. FIGURE 18-3: To prevent the generation of an incomplete waveform when the PWM is first enabled, the ECCP module waits until the start of a new PWM period before generating a PWM signal. EXAMPLE SIMPLIFIED BLOCK DIAGRAM OF THE ENHANCED PWM MODE Duty Cycle Registers DCxB CCPxM 4 PxM 2 CCPRxL ECCP1/Output Pin(3) ECCPx/PxA TRIS(2) CCPRxH (Slave) Output Pin(3) PxB Comparator R Q Output Controller TRIS(2) Output Pin(3) PxC TMR2 Comparator PR2 Note 1: (1) TRIS(2) S PxD Clear Timer2, Toggle PWM Pin and Latch Duty Cycle Output Pin(3) TRIS(2) ECCPxDEL The 8-bit TMR2 register is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler, to create the 10-bit time base. 2: The TRIS register value for each PWM output must be configured appropriately. 3: Any pin not used by an Enhanced PWM mode is available for alternate pin functions.  2012-2016 Microchip Technology Inc. DS30000575C-page 321 PIC18F97J94 FAMILY TABLE 18-3: EXAMPLE PIN ASSIGNMENTS FOR VARIOUS PWM ENHANCED MODES ECCP Mode PxM PxA PxB PxC PxD Single 00 Yes(1) Yes(1) Yes(1) Yes(1) Half-Bridge 10 Yes Yes No No Full-Bridge, Forward 01 Yes Yes Yes Yes Full-Bridge, Reverse 11 Yes Yes Yes Yes Note 1: Outputs are enabled by pulse steering in Single mode (see Register 18-5). FIGURE 18-4: EXAMPLE PWM (ENHANCED MODE) OUTPUT RELATIONSHIPS (ACTIVE-HIGH STATE) Signal PxM 0 PR2 + 1 Pulse Width Period 00 (Single Output) PxA Modulated Delay(1) Delay(1) PxA Modulated 10 (Half-Bridge) PxB Modulated PxA Active 01 (Full-Bridge, Forward) PxB Inactive PxC Inactive PxD Modulated PxA Inactive 11 (Full-Bridge, Reverse) PxB Modulated PxC Active PxD Inactive Relationships: • Period = 4 * TOSC * (PR2 + 1) * (TMR2 Prescale Value) • Pulse Width = TOSC * (CCPRxL:CCPxCON) * (TMR2 Prescale Value) • Delay = 4 * TOSC * (ECCPxDEL) Note 1: Dead-band delay is programmed using the ECCPxDEL register (Section 18.4.6 “Programmable Dead-Band Delay Mode”). DS30000575C-page 322  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 18-5: EXAMPLE ENHANCED PWM OUTPUT RELATIONSHIPS (ACTIVE-LOW STATE) PxM Signal PR2 + 1 Pulse Width 0 Period 00 (Single Output) PxA Modulated PxA Modulated 10 (Half-Bridge) Delay(1) Delay(1) PxB Modulated PxA Active 01 (Full-Bridge, Forward) PxB Inactive PxC Inactive PxD Modulated PxA Inactive 11 (Full-Bridge, Reverse) PxB Modulated PxC Active PxD Inactive Relationships: • Period = 4 * TOSC * (PR2 + 1) * (TMR2 Prescale Value) • Pulse Width = TOSC * (CCPRxL:CCPxCON) * (TMR2 Prescale Value) • Delay = 4 * TOSC * (ECCPxDEL) Note 1: Dead-band delay is programmed using the ECCPxDEL register (Section 18.4.6 “Programmable Dead-Band Delay Mode”).  2012-2016 Microchip Technology Inc. DS30000575C-page 323 PIC18F97J94 FAMILY 18.4.1 HALF-BRIDGE MODE Since the PxA and PxB outputs are multiplexed with the PORT data latches, the associated TRIS bits must be cleared to configure PxA and PxB as outputs. In Half-Bridge mode, two pins are used as outputs to drive push-pull loads. The PWM output signal is output on the PxA pin, while the complementary PWM output signal is output on the PxB pin (see Figure 18-6). This mode can be used for half-bridge applications, as shown in Figure 18-7, or for full-bridge applications, where four power switches are being modulated with two PWM signals. FIGURE 18-6: Period Period Pulse Width PxA(2) In Half-Bridge mode, the programmable dead-band delay can be used to prevent shoot-through current in halfbridge power devices. The value of the PxDC bits of the ECCPxDEL register sets the number of instruction cycles before the output is driven active. If the value is greater than the duty cycle, the corresponding output remains inactive during the entire cycle. For more details on the dead-band delay operations, see Section 18.4.6 “Programmable Dead-Band Delay Mode”. td td PxB(2) (1) (1) (1) td = Dead-Band Delay Note 1: 2: FIGURE 18-7: EXAMPLE OF HALFBRIDGE PWM OUTPUT At this time, the TMR2 register is equal to the PR2 register. Output signals are shown as active-high. EXAMPLE OF HALF-BRIDGE APPLICATIONS Standard Half-Bridge Circuit (“Push-Pull”) FET Driver + PxA Load FET Driver + PxB - Half-Bridge Output Driving a Full-Bridge Circuit V+ FET Driver FET Driver PxA FET Driver Load FET Driver PxB DS30000575C-page 324  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 18.4.2 FULL-BRIDGE MODE In the Reverse mode, the PxC pin is driven to its active state and the PxB pin is modulated, while the PxA and PxD pins are driven to their inactive state, as provided in Figure 18-9. In Full-Bridge mode, all four pins are used as outputs. An example of a full-bridge application is provided in Figure 18-8. The PxA, PxB, PxC and PxD outputs are multiplexed with the port data latches. The associated TRIS bits must be cleared to configure the PxA, PxB, PxC and PxD pins as outputs. In the Forward mode, the PxA pin is driven to its active state and the PxD pin is modulated, while the PxB and PxC pins are driven to their inactive state, as provided in Figure 18-9. FIGURE 18-8: EXAMPLE OF FULL-BRIDGE APPLICATION V+ FET Driver QC QA FET Driver PxA Load PxB FET Driver PxC FET Driver QD QB VPxD  2012-2016 Microchip Technology Inc. DS30000575C-page 325 PIC18F97J94 FAMILY FIGURE 18-9: EXAMPLE OF FULL-BRIDGE PWM OUTPUT Forward Mode Period PxA (2) Pulse Width PxB(2) PxC(2) PxD(2) (1) (1) Reverse Mode Period Pulse Width PxA(2) PxB(2) PxC(2) PxD(2) (1) Note 1: 2: (1) At this time, the TMR2 register is equal to the PR2 register. The output signal is shown as active-high. DS30000575C-page 326  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 18.4.2.1 Direction Change in Full-Bridge Mode In Full-Bridge mode, the PxM1 bit in the CCPxCON register allows users to control the forward/reverse direction. When the application firmware changes this direction control bit, the module will change to the new direction on the next PWM cycle. A direction change is initiated in software by changing the PxM1 bit of the CCPxCON register. The following sequence occurs prior to the end of the current PWM period: • The modulated outputs (PxB and PxD) are placed in their inactive state. • The associated unmodulated outputs (PxA and PxC) are switched to drive in the opposite direction. • PWM modulation resumes at the beginning of the next period. For an illustration of this sequence, see Figure 18-10. The Full-Bridge mode does not provide a dead-band delay. As one output is modulated at a time, a deadband delay is generally not required. There is a situation where a dead-band delay is required. This situation occurs when both of the following conditions are true: FIGURE 18-10: • The direction of the PWM output changes when the duty cycle of the output is at or near 100%. • The turn-off time of the power switch, including the power device and driver circuit, is greater than the turn-on time. Figure 18-11 shows an example of the PWM direction changing from forward to reverse, at a near 100% duty cycle. In this example, at time, t1, the PxA and PxD outputs become inactive, while the PxC output becomes active. Since the turn-off time of the power devices is longer than the turn-on time, a shoot-through current will flow through power devices, QC and QD (see Figure 18-8), for the duration of ‘t’. The same phenomenon will occur to power devices, QA and QB, for PWM direction change from reverse to forward. If changing PWM direction at high duty cycle is required for an application, two possible solutions for eliminating the shoot-through current are: • Reduce PWM duty cycle for one PWM period before changing directions. • Use switch drivers that can drive the switches off faster than they can drive them on. Other options to prevent shoot-through current may exist. EXAMPLE OF PWM DIRECTION CHANGE Period(1) Signal Period PxA (Active-High) PxB (Active-High) Pulse Width PxC (Active-High) (2) PxD (Active-High) Pulse Width Note 1: 2: The direction bit, PxM1 of the CCPxCON register, is written any time during the PWM cycle. When changing directions, the PxA and PxC signals switch before the end of the current PWM cycle. The modulated PxB and PxD signals are inactive at this time. The length of this time is: (1/FOSC) • TMR2 Prescale Value.  2012-2016 Microchip Technology Inc. DS30000575C-page 327 PIC18F97J94 FAMILY FIGURE 18-11: EXAMPLE OF PWM DIRECTION CHANGE AT NEAR 100% DUTY CYCLE Forward Period t1 Reverse Period PxA PxB PW PxC PxD PW TON External Switch C TOFF External Switch D Potential Shoot-Through Current Note 1: 18.4.3 All signals are shown as active-high. 2: TON is the turn-on delay of power switch QC and its driver. 3: TOFF is the turn-off delay of power switch QD and its driver. START-UP CONSIDERATIONS When any PWM mode is used, the application hardware must use the proper external pull-up and/or pull-down resistors on the PWM output pins. Note: T = TOFF – TON When the microcontroller is released from Reset, all of the I/O pins are in the highimpedance state. The external circuits must keep the power switch devices in the OFF state until the microcontroller drives the I/O pins with the proper signal levels or activates the PWM output(s). The CCPxM bits of the CCPxCON register allow the user to choose whether the PWM output signals are active-high or active-low for each pair of PWM output pins (PxA/PxC and PxB/PxD). The PWM output polarities must be selected before the PWM pin output drivers are enabled. Changing the polarity configuration while the PWM pin output drivers are enabled is not recommended since it may result in damage to the application circuits. The PxA, PxB, PxC and PxD output latches may not be in the proper states when the PWM module is initialized. Enabling the PWM pin output drivers, at the same time as the Enhanced PWM modes, may cause damage to the application circuit. The Enhanced PWM modes must be enabled in the proper Output mode and complete a full PWM cycle before enabling the PWM DS30000575C-page 328 pin output drivers. The completion of a full PWM cycle is indicated by the TMR2IF or TMR4IF bit of the PIR1 or PIR5 register being set as the second PWM period begins. 18.4.4 ENHANCED PWM AUTOSHUTDOWN MODE The PWM mode supports an Auto-Shutdown mode that will disable the PWM outputs when an external shutdown event occurs. Auto-Shutdown mode places the PWM output pins into a predetermined state. This mode is used to help prevent the PWM from damaging the application. The auto-shutdown sources are selected using the ECCPxAS bits (ECCPxAS). A shutdown event may be generated by: • A logic ‘0’ on the pin that is assigned the FLT0 input function • Comparator C1 • Comparator C2 • Setting the ECCPxASE bit in firmware A shutdown condition is indicated by the ECCPxASE (Auto-Shutdown Event Status) bit (ECCPxAS). If the bit is a ‘0’, the PWM pins are operating normally. If the bit is a ‘1’, the PWM outputs are in the shutdown state.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY When a shutdown event occurs, two things happen: Each pin pair may be placed into one of three states: • The ECCPxASE bit is set to ‘1’. The ECCPxASE will remain set until cleared in firmware or an auto-restart occurs. (See Section 18.4.5 “AutoRestart Mode”.) • The enabled PWM pins are asynchronously placed in their shutdown states. The PWM output pins are grouped into pairs (PxA/PxC and PxB/ PxD). The state of each pin pair is determined by the PSSxAC and PSSxBD bits (ECCPxAS and , respectively). • Drive logic ‘1’ • Drive logic ‘0’ • Tri-state (high-impedance) REGISTER 18-3: ECCPxAS: ECCPx AUTO-SHUTDOWN CONTROL REGISTER(1,2,3) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCPxASE ECCPxAS2 ECCPxAS1 ECCPxAS0 PSSxAC1 PSSxAC0 PSSxBD1 PSSxBD0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 ECCPxASE: ECCP Auto-Shutdown Event Status bit 1 = A shutdown event has occurred; ECCP outputs are in a shutdown state 0 = ECCP outputs are operating bit 6-4 ECCPxAS: ECCP Auto-Shutdown Source Select bits 000 = Auto-shutdown is disabled 001 = Comparator C1OUT output is high 010 = Comparator C2OUT output is high 011 = Either Comparator C1OUT or C2OUT is high 100 = VIL on FLT0 pin 101 = VIL on FLT0 pin or Comparator C1OUT output is high 110 = VIL on FLT0 pin or Comparator C2OUT output is high 111 = VIL on FLT0 pin or Comparator C1OUT or Comparator C2OUT is high bit 3-2 PSSxAC: PxA and PxC Pins Shutdown State Control bits 00 = Drive pins: PxA and PxC to ‘0’ 01 = Drive pins: PxA and PxC to ‘1’ 1x = PxA and PxC pins tri-state bit 1-0 PSSxBD: Pins PxB and PxD Shutdown State Control bits 00 = Drive pins: PxB and PxD to ‘0’ 01 = Drive pins: PxB and PxD to ‘1’ 1x = PxB and PxD pins tri-state Note 1: 2: 3: The auto-shutdown condition is a level-based signal, not an edge-based signal. As long as the level is present, the auto-shutdown will persist. Writing to the ECCPxASE bit is disabled while an auto-shutdown condition persists. Once the auto-shutdown condition has been removed and the PWM restarted (either through firmware or auto-restart), the PWM signal will always restart at the beginning of the next PWM period.  2012-2016 Microchip Technology Inc. DS30000575C-page 329 PIC18F97J94 FAMILY FIGURE 18-12: PWM AUTO-SHUTDOWN WITH FIRMWARE RESTART (PxRSEN = 0) PWM Period Shutdown Event ECCPxASE bit PWM Activity Normal PWM Start of PWM Period 18.4.5 Shutdown Event Occurs AUTO-RESTART MODE The Enhanced PWM can be configured to automatically restart the PWM signal once the auto-shutdown condition has been removed. Auto-restart is enabled by setting the PxRSEN bit (ECCPxDEL). ECCPxASE Cleared by Shutdown PWM Firmware Event Clears Resumes The module will wait until the next PWM period begins, however, before re-enabling the output pin. This behavior allows the auto-shutdown with auto-restart features to be used in applications based on current mode of PWM control. If auto-restart is enabled, the ECCPxASE bit will remain set as long as the auto-shutdown condition is active. When the auto-shutdown condition is removed, the ECCPxASE bit will be cleared via hardware and normal operation will resume. FIGURE 18-13: PWM AUTO-SHUTDOWN WITH AUTO-RESTART ENABLED (PxRSEN = 1) PWM Period Shutdown Event ECCPxASE bit PWM Activity Normal PWM Start of PWM Period DS30000575C-page 330 Shutdown Event Occurs Shutdown Event Clears PWM Resumes  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 18.4.6 PROGRAMMABLE DEAD-BAND DELAY MODE FIGURE 18-14: In half-bridge applications, where all power switches are modulated at the PWM frequency, the power switches normally require more time to turn off than to turn on. If both the upper and lower power switches are switched at the same time (one turned on and the other turned off), both switches may be on for a short period until one switch completely turns off. During this brief interval, a very high current (shoot-through current) will flow through both power switches, shorting the bridge supply. To avoid this potentially destructive shoot-through current from flowing during switching, turning on either of the power switches is normally delayed to allow the other switch to completely turn off. Period Period Pulse Width PxA(2) td td PxB(2) (1) (1) (1) td = Dead-Band Delay Note 1: In Half-Bridge mode, a digitally programmable deadband delay is available to avoid shoot-through current from destroying the bridge power switches. The delay occurs at the signal transition from the non-active state to the active state. For an illustration, see Figure 18-14. The lower seven bits of the associated ECCPxDEL register (Register 18-4) set the delay period in terms of microcontroller instruction cycles (TCY or 4 TOSC). FIGURE 18-15: EXAMPLE OF HALFBRIDGE PWM OUTPUT 2: At this time, the TMR2 register is equal to the PR2 register. Output signals are shown as active-high. EXAMPLE OF HALF-BRIDGE APPLICATIONS V+ Standard Half-Bridge Circuit (“Push-Pull”) FET Driver + V - PxA Load FET Driver + V - PxB V-  2012-2016 Microchip Technology Inc. DS30000575C-page 331 PIC18F97J94 FAMILY REGISTER 18-4: ECCPxDEL: ENHANCED PWM CONTROL REGISTER x R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PxRSEN PxDC6 PxDC5 PxDC4 PxDC3 PxDC2 PxDC1 PxDC0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 PxRSEN: PWM Restart Enable bit 1 = Upon auto-shutdown, the ECCPxASE bit clears automatically once the shutdown event goes away; the PWM restarts automatically 0 = Upon auto-shutdown, ECCPxASE must be cleared by software to restart the PWM bit 6-0 PxDC: PWM Delay Count bits PxDCn=Number of FOSC/4 (4 * TOSC) cycles between the scheduled time when a PWM signal should transition active and the actual time it does transition active. 18.4.7 PULSE STEERING MODE In Single Output mode, pulse steering allows any of the PWM pins to be the modulated signal. Additionally, the same PWM signal can simultaneously be available on multiple pins. Once the Single Output mode is selected (CCPxM = 11 and PxM = 00 of the CCPxCON register), the user firmware can bring out the same PWM signal to one, two, three or four output pins by setting the appropriate STR bits (PSTRxCON), as provided in Table 18-3. Note: While the PWM Steering mode is active, the CCPxM bits (CCPxCON) select the PWM output polarity for the Px pins. The PWM auto-shutdown operation also applies to the PWM Steering mode, as described in Section 18.4.4 “Enhanced PWM Auto-shutdown mode”. An autoshutdown event will only affect pins that have PWM outputs enabled. The associated TRIS bits must be set to output (‘0’) to enable the pin output driver in order to see the PWM signal on the pin. DS30000575C-page 332  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 18-5: R/W-0 CMPL1 PSTRxCON: PULSE STEERING CONTROL(1) R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-1 CMPL0 — STRSYNC STRD STRC STRB STRA bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 CMPL: Complementary Mode Output Assignment Steering Sync bits 00 =See STR 01 =PA and PB are selected as the complementary output pair 10 =PA and PC are selected as the complementary output pair 11 =PA and PD are selected as the complementary output pair bit 5 Unimplemented: Read as ‘0’ bit 4 STRSYNC: Steering Sync bit 1 = Output steering update occurs on the next PWM period 0 = Output steering update occurs at the beginning of the instruction cycle boundary bit 3 STRD: Steering Enable bit D 1 = PxD pin has the PWM waveform with polarity control from CCPxM 0 = PxD pin is assigned to port pin bit 2 STRC: Steering Enable bit C 1 = PxC pin has the PWM waveform with polarity control from CCPxM 0 = PxC pin is assigned to port pin bit 1 STRB: Steering Enable bit B 1 = PxB pin has the PWM waveform with polarity control from CCPxM 0 = PxB pin is assigned to port pin bit 0 STRA: Steering Enable bit A 1 = PxA pin has the PWM waveform with polarity control from CCPxM 0 = PxA pin is assigned to port pin Note 1: The PWM Steering mode is available only when the CCPxCON register bits, CCPxM = 11 and PxM = 00.  2012-2016 Microchip Technology Inc. DS30000575C-page 333 PIC18F97J94 FAMILY FIGURE 18-16: SIMPLIFIED STEERING BLOCK DIAGRAM STRA(2) PxA Signal CCPxM1 1 PORT Data 0 Output Pin(1) TRIS STRB(2) CCPxM0 1 PORT Data 0 STRC Output Pin(1) CCPxM1 1 PORT Data 0 Output Pin(1) CCPxM0 1 PORT Data 0 2: The STRSYNC bit of the PSTRxCON register gives the user two choices for when the steering event will happen. When the STRSYNC bit is ‘0’, the steering event will happen at the end of the instruction that writes to the PSTRxCON register. In this case, the output signal at the Px pins may be an incomplete PWM waveform. This operation is useful when the user firmware needs to immediately remove a PWM signal from the pin. Figures 18-17 and 18-18 illustrate the timing diagrams of the PWM steering depending on the STRSYNC setting. TRIS STRD(2) Note 1: Steering Synchronization When the STRSYNC bit is ‘1’, the effective steering update will happen at the beginning of the next PWM period. In this case, steering on/off the PWM output will always produce a complete PWM waveform. TRIS (2) 18.4.7.1 Output Pin(1) TRIS Port outputs are configured as displayed when the CCPxCON register bits, PxM = 00 and CCPxM = 11. Single PWM output requires setting at least one of the STRx bits. FIGURE 18-17: EXAMPLE OF STEERING EVENT AT END OF INSTRUCTION (STRSYNC = 0) PWM Period PWM STRn P1 PORT Data PORT Data P1n = PWM FIGURE 18-18: EXAMPLE OF STEERING EVENT AT BEGINNING OF INSTRUCTION (STRSYNC = 1) PWM STRn P1 PORT Data PORT Data P1n = PWM DS30000575C-page 334  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 18.4.8 OPERATION IN POWER-MANAGED MODES 18.4.8.1 Operation with Fail-Safe Clock Monitor (FSCM) In Sleep mode, all clock sources are disabled. Timer2/ 4/6/8 will not increment and the state of the module will not change. If the ECCPx pin is driving a value, it will continue to drive that value. When the device wakes up, it will continue from this state. If Two-Speed Startups are enabled, the initial start-up frequency from HFINTOSC and the postscaler may not be stable immediately. If the Fail-Safe Clock Monitor (FSCM) is enabled, a clock failure will force the device into the power-managed RC_RUN mode and the OSCFIF bit of the PIR2 register will be set. The ECCPx will then be clocked from the internal oscillator clock source, which may have a different clock frequency than the primary clock. In PRI_IDLE mode, the primary clock will continue to clock the ECCPx module without change. Both Power-on Reset and subsequent Resets will force all ports to Input mode and the ECCP registers to their Reset states. 18.4.9 EFFECTS OF A RESET This forces the ECCP module to reset to a state compatible with previous, non-enhanced CCP modules used on other PIC18 and PIC16 devices.  2012-2016 Microchip Technology Inc. DS30000575C-page 335 PIC18F97J94 FAMILY 19.0 CAPTURE/COMPARE/PWM (CCP) MODULES PIC18FXXJ94 devices have seven CCP (Capture/ Compare/PWM) modules, designated CCP4 through CCP10. All the modules implement standard Capture, Compare and Pulse-Width Modulation (PWM) modes. Note: Each CCP module contains a 16-bit register that can operate as a 16-bit Capture register, a 16-bit Compare register or a PWM Master/Slave Duty Cycle register. For the sake of clarity, all CCP module operation in the following sections is described with respect to CCP4, but is equally applicable to CCP5 through CCP10. Throughout this section, generic references are used for register and bit names that are the same, except for an ‘x’ variable that indicates the item’s association with the specific CCP module. For example, the control register is named CCPxCON and refers to CCP4CON through CCP10CON. REGISTER 19-1: U-0 CCPxCON: CCPx CONTROL REGISTER (CCP4-CCP10 MODULES) U-0 — — R/W-0 DCxB1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DCxB0 CCPxM3(1) CCPxM2(1) CCPxM1(1) CCPxM0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 DCxB: PWM Duty Cycle bit 1 and bit 0 for CCPx module bits Capture mode: Unused. Compare mode: Unused. PWM mode: These bits are the two Least Significant bits (bit 1 and bit 0) of the 10-bit PWM duty cycle. The eight Most Significant bits (DCx) of the duty cycle are found in CCPRxL. bit 3-0 CCPxM: CCPx Module Mode Select bits(1) 0000 =Capture/Compare/PWM is disabled (resets CCPx module) 0001 =Reserved 0010 =Compare mode, toggles output on match (CCPxIF bit is set) 0011 =Reserved 0100 =Capture mode: Every falling edge 0101 =Capture mode: Every rising edge 0110 =Capture mode: Every 4th rising edge 0111 =Capture mode: Every 16th rising edge 1000 =Compare mode: Initialize CCPx pin low; on compare match, force CCPx pin high (CCPxIF bit is set) 1001 =Compare mode: Initialize CCPx pin high; on compare match, force CCPx pin low (CCPxIF bit is set) 1010 =Compare mode: Generate software interrupt on compare match (CCPxIF bit is set, CCPx pin reflects I/O state) 1011 =Compare mode: Special Event Trigger; reset timer on CCPx match (CCPxIF bit is set) 11xx =PWM mode Note 1: CCPxM = 1011 will only reset the timer and not start an A/D conversion on a CCPx match. DS30000575C-page 336  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 19-2: CCPTMRS1: CCP TIMER SELECT REGISTER 1 R/W-0 R/W-0 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 C7TSEL1 C7TSEL0 — C6TSEL0 — C5TSEL0 C4TSEL1 C4TSEL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-6 C7TSEL: CCP7 Timer Selection bits 00 =CCP7 is based off of TMR1/TMR2 01 =CCP7 is based off of TMR5/TMR4 10 =CCP7 is based off of TMR5/TMR6 11 =CCP7 is based off of TMR5/TMR8 bit 5 Unimplemented: Read as ‘0’ bit 4 C6TSEL0: CCP6 Timer Selection bit 0 = CCP6 is based off of TMR1/TMR2 1 = CCP6 is based off of TMR5/TMR2 bit 3 Unimplemented: Read as ‘0’ bit 2 C5TSEL0: CCP5 Timer Selection bit 0 = CCP5 is based off of TMR1/TMR2 1 = CCP5 is based off of TMR5/TMR4 bit 1-0 C4TSEL: CCP4 Timer Selection bits 00 =CCP4 is based off of TMR1/TMR2 01 =CCP4 is based off of TMR3/TMR4 10 =CCP4 is based off of TMR3/TMR6 11 =Reserved; do not use  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 337 PIC18F97J94 FAMILY REGISTER 19-3: CCPTMRS2: CCP TIMER SELECT REGISTER 2 U-0 U-0 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 — — — C10TSEL0 — C9TSEL0 C8TSEL1 C8TSEL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-5 Unimplemented: Read as ‘0’ bit 4 C10TSEL0: CCP10 Timer Selection bit 0 = CCP10 is based off of TMR1/TMR2 1 = CCP10 is based off of TMR5/TMR2 bit 3 Unimplemented: Read as ‘0’ bit 2 C9TSEL0: CCP9 Timer Selection bit 0 = CCP9 is based off of TMR1/TMR2 1 = CCP9 is based off of TMR5/TMR4 bit 1-0 C8TSEL: CCP8 Timer Selection bits 00 =CCP8 is based off of TMR1/TMR2 01 =CCP8 is based off of TMR3/TMR4 10 =CCP8 is based off of TMR3/TMR6 11 =Reserved; do not use DS30000575C-page 338 x = Bit is unknown  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 19-4: CCPRxL: CCPx PERIOD LOW BYTE REGISTER R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x CCPRxL7 CCPRxL6 CCPRxL5 CCPRxL4 CCPRxL3 CCPRxL2 CCPRxL1 CCPRxL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 x = Bit is unknown CCPRxL: CCPx Period Register Low Byte bits Capture mode: Capture Register Low Byte Compare mode: Compare Register Low Byte PWM mode: Duty Cycle Register REGISTER 19-5: CCPRxH: CCPx PERIOD HIGH BYTE REGISTER R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x CCPRxH7 CCPRxH6 CCPRxH5 CCPRxH4 CCPRxH3 CCPRxH2 CCPRxH1 CCPRxH0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 x = Bit is unknown CCPRxH: CCPx Period Register High Byte bits Capture mode: Capture Register High Byte Compare mode: Compare Register High Byte PWM mode: Duty Cycle Buffer Register  2012-2016 Microchip Technology Inc. DS30000575C-page 339 PIC18F97J94 FAMILY 19.1 CCP Module Configuration TABLE 19-1: Each Capture/Compare/PWM module is associated with a control register (generically, CCPxCON) and a data register (CCPRx). The data register, in turn, is comprised of two 8-bit registers: CCPRxL (low byte) and CCPRxH (high byte). All registers are both readable and writable. 19.1.1 CCP MODULES AND TIMER RESOURCES The CCP modules utilize Timers, 1 through 8, that vary with the selected mode. Various timers are available to the CCP modules in Capture, Compare or PWM modes, as shown in Table 19-1. CCP MODE – TIMER RESOURCE CCP Mode Timer Resource Capture Timer1, Timer3 or Timer 5 Compare PWM Timer2, Timer4, Timer 6 or Timer8 The assignment of a particular timer to a module is determined by the timer to CCP enable bits in the CCPTMRSx registers. (See Register 19-2 and Register 19-3.) All of the modules may be active at once and may share the same timer resource if they are configured to operate in the same mode (Capture/ Compare or PWM) at the same time. The CCPTMRS1 register selects the timers for CCP modules, 7, 6, 5 and 4, and the CCPTMRS2 register selects the timers for CCP modules, 10, 9 and 8. The possible configurations are shown in Table 19-2 and Table 19-3. TABLE 19-2: TIMER ASSIGNMENTS FOR CCP MODULES 4, 5, 6 AND 7 CCPTMRS1 Register CCP4 CCP5 CCP6 CCP7 Capture/ Capture/ Capture/ PWM PWM C4TSEL C6TSEL0 Compare C5TSEL0 Compare Compare Mode Mode Mode Mode Mode Capture/ PWM PWM C7TSEL Compare Mode Mode Mode 0 0 TMR1 TMR2 0 TMR1 TMR2 0 TMR1 TMR2 0 0 TMR1 TMR2 0 1 TMR3 TMR4 1 TMR5 TMR4 1 TMR5 TMR2 0 1 TMR5 TMR4 1 0 TMR3 TMR6 1 0 TMR5 TMR6 1 1 TMR5 TMR8 1 1 Note 1: Reserved(1) Do not use the reserved bits. TABLE 19-3: TIMER ASSIGNMENTS FOR CCP MODULES 8, 9 AND 10 CCPTMRS2 Register CCP8 Devices with 32 Kbytes CCP8 CCP9 CCP10 Capture/ Capture/ Capture/ Capture/ C8TSEL PWM C8TSEL PWM PWM PWM Compare Compare C9TSEL0 Compare C10TSEL0 Compare Mode Mode Mode Mode Mode Mode Mode Mode 0 0 TMR1 TMR2 0 0 TMR1 TMR2 0 TMR1 TMR2 0 TMR1 TMR2 0 1 TMR5 TMR4 0 1 TMR1 TMR4 1 TMR5 TMR4 1 TMR5 TMR2 1 0 TMR5 TMR6 1 0 TMR1 TMR6 1 1 Note 1: Reserved(1) 1 1 Reserved(1) Do not use the reserved bits. DS30000575C-page 340  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 19.1.2 OPEN-DRAIN OUTPUT OPTION When operating in Output mode (the Compare or PWM modes), the drivers for the CCPx pins can be optionally configured as open-drain outputs. This feature allows the voltage level on the pin to be pulled to a higher level through an external pull-up resistor and allows the output to communicate with external circuits without the need for additional level shifters. The open-drain output option is controlled by the CCPxOD bits (ODCON2). Setting the appropriate bit configures the pin for the corresponding module for open-drain operation. 19.2 Capture Mode In Capture mode, the CCPR4H:CCPR4L register pair captures the 16-bit value of the Timer register selected in the CCPTMRS1 when an event occurs on the CCP4 pin. An event is defined as one of the following: • • • • Every falling edge Every rising edge Every 4th rising edge Every 16th rising edge The event is selected by the mode select bits, CCP4M (CCP4CON). When a capture is made, the interrupt request flag bit, CCP4IF (PIR4), is set. (It must be cleared in software.) If another capture occurs before the value in CCPR4 is read, the old captured value is overwritten by the new captured value. Figure 19-1 shows the Capture mode block diagram. 19.2.1 CCP PIN CONFIGURATION In Capture mode, the appropriate CCPx pin should be configured as an input by setting the corresponding TRIS direction bit. Note: 19.2.2 If the CCPx pin is configured as an output, a write to the port can cause a capture condition. TIMER1/3/5/7 MODE SELECTION For the available timers (1/3/5) to be used for the capture feature, the used timers must be running in Timer mode or Synchronized Counter mode. In Asynchronous Counter mode, the capture operation will not work. The timer to be used with each CCP module is selected in the CCPTMRSx registers. (See Section 19.1.1 “CCP Modules and Timer Resources”.) Details of the timer assignments for the CCP modules are given in Table 19-2 and Table 19-3.  2012-2016 Microchip Technology Inc. DS30000575C-page 341 PIC18F97J94 FAMILY FIGURE 19-1: CAPTURE MODE OPERATION BLOCK DIAGRAM TMR5H Set CCP5IF TMR5 Enable C5TSEL0 CCP5 Pin Prescaler  1, 4, 16 and Edge Detect CCPR5H Q1:Q4 4 4 TMR1H TMR1L TMR3H TMR3L Set CCP4IF 4 CCP4CON C4TSEL1 C4TSEL0 TMR3 Enable CCP4 Pin Prescaler  1, 4, 16 CCPR5L TMR1 Enable C5TSEL0 CCP5CON TMR5L and Edge Detect CCPR4H CCPR4L TMR1 Enable C4TSEL0 C4TSEL1 Note: 19.2.3 TMR1L This block diagram uses CCP4 and CCP5, and their appropriate timers as an example. For details on all of the CCP modules and their timer assignments, see Table 19-2 and Table 19-3. SOFTWARE INTERRUPT When the Capture mode is changed, a false capture interrupt may be generated. The user should keep the CCP4IE bit (PIE4) clear to avoid false interrupts and should clear the flag bit, CCP4IF, following any such change in operating mode. 19.2.4 TMR1H CCP PRESCALER There are four prescaler settings in Capture mode. They are specified as part of the operating mode selected by the mode select bits (CCP4M). Whenever the CCP module is turned off, or the CCP module is not in Capture mode, the prescaler counter is cleared. This means that any Reset will clear the prescaler counter. DS30000575C-page 342 Switching from one capture prescaler to another may generate an interrupt. Doing that will also not clear the prescaler counter – meaning the first capture may be from a non-zero prescaler. Example 19-1 shows the recommended method for switching between capture prescalers. This example also clears the prescaler counter and will not generate the “false” interrupt. EXAMPLE 19-1: CHANGING BETWEEN CAPTURE PRESCALERS CLRF CCP4CON ; Turn CCP module off MOVLW NEW_CAPT_PS ; Load WREG with the ; new prescaler mode ; value and CCP ON MOVWF CCP4CON ; Load CCP4CON with ; this value  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 19.3 Compare Mode 19.3.3 SOFTWARE INTERRUPT MODE In Compare mode, the 16-bit CCPR4 register value is constantly compared against the Timer register pair value selected in the CCPTMR1 register. When a match occurs, the CCP4 pin can be: When the Generate Software Interrupt mode is chosen (CCP4M = 1010), the CCP4 pin is not affected. Only a CCP interrupt is generated, if enabled, and the CCP4IE bit is set. • • • • 19.3.4 Driven high Driven low Toggled (high-to-low or low-to-high) Unchanged (that is, reflecting the state of the I/O latch) The action on the pin is based on the value of the mode select bits (CCP4M). At the same time, the interrupt flag bit, CCP4IF, is set. Figure 19-2 gives the Compare mode block diagram 19.3.1 CCP PIN CONFIGURATION The user must configure the CCPx pin as an output by clearing the appropriate TRIS bit. Note: 19.3.2 Clearing the CCPxCON register will force the CCPx compare output latch (depending on device configuration) to the default low level. This is not the PORTx I/O data latch. SPECIAL EVENT TRIGGER Both CCP modules are equipped with a Special Event Trigger. This is an internal hardware signal, generated in Compare mode, to trigger actions by other modules. The Special Event Trigger is enabled by selecting the Compare Special Event Trigger mode (CCP4M = 1011). For either CCP module, the Special Event Trigger resets the Timer register pair for whichever timer resource is currently assigned as the module’s time base. This allows the CCPRx registers to serve as a Programmable Period register for either timer. The Special Event Trigger for CCP4 cannot start an A/ D conversion. TIMER1/3/5 MODE SELECTION If the CCP module is using the compare feature in conjunction with any of the Timer1/3/5 timers, the timers must be running in Timer mode or Synchronized Counter mode. In Asynchronous Counter mode, the compare operation will not work. Note: Details of the timer assignments for the CCP modules are given in Table 19-2 and Table 19-3.  2012-2016 Microchip Technology Inc. DS30000575C-page 343 PIC18F97J94 FAMILY FIGURE 19-2: COMPARE MODE OPERATION BLOCK DIAGRAM CCPR5H Set CCP5IF CCPR5L Special Event Trigger (Timer1/5 Reset) CCP5 Pin Compare Match Comparator S Output Logic Q R TRIS Output Enable 4 CCP5CON TMR1H TMR1L 0 TMR5H TMR5L 1 C5TSEL0 0 TMR1H TMR1L 1 TMR3H TMR3L Special Event Trigger (Timer1/Timer3 Reset) C4TSEL1 C4TSEL0 Set CCP4IF Comparator CCPR4H CCPR4L Compare Match CCP4 Pin Output Logic 4 S Q R TRIS Output Enable CCP4CON Note: This block diagram uses CCP4 and CCP5 and their appropriate timers as an example. For details on all of the CCP modules and their timer assignments, see Table 19-2 and Table 19-3. DS30000575C-page 344  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 19.4 PWM Mode In Pulse-Width Modulation (PWM) mode, the CCP4 pin produces up to a 10-bit resolution PWM output. Since the CCP4 pin is multiplexed with a PORTC or PORTE data latch, the appropriate TRIS bit must be cleared to make the CCP4 pin an output. Note: A PWM output (Figure 19-4) has a time base (period) and a time that the output stays high (duty cycle). The frequency of the PWM is the inverse of the period (1/ period). FIGURE 19-4: PWM OUTPUT Period Clearing the CCPxCON register will force the CCPx compare output latch (depending on device configuration) to the default low level. This is not the PORTx I/O data latch. Duty Cycle TMR2 = PR2 Figure 19-3 shows a simplified block diagram of the CCP4 module in PWM mode. For a step-by-step procedure on how to set up the CCP module for PWM operation, see Section 19.4.3 “Setup for PWM Operation”. FIGURE 19-3: SIMPLIFIED PWM BLOCK DIAGRAM Duty Cycle Registers TMR2 = Duty Cycle TMR2 = PR2 19.4.1 PWM PERIOD The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following formula: CCP4CON EQUATION 19-1: CCPR4L PWM PERIOD CALCULATION PWM Period = [(PR2) + 1] • 4 • TOSC • (TMR2 Prescale Value) CCPR4H (Slave) PWM frequency is defined as 1/[PWM period]. Comparator R Q RC2/CCP4 TMR2 (Note 1) S Comparator PR2 TRISC Clear Timer, CCP4 Pin and Latch D.C. Note 1: The 8-bit TMR2 value is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler, to create the 10-bit time base. 2: CCP4 and its appropriate timers are used as an example. For details on all of the CCP modules and their timer assignments, see Table 19-2 and Table 19-3.  2012-2016 Microchip Technology Inc. When TMR2 is equal to PR2, the following three events occur on the next increment cycle: • TMR2 is cleared • The CCP4 pin is set (An exception: If PWM Duty Cycle = 0%, the CCP4 pin will not be set) • The PWM duty cycle is latched from CCPR4L into CCPR4H Note: The Timer2 postscalers (see Section 16.0 “Timer2/4/6/8 Modules”) are not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. DS30000575C-page 345 PIC18F97J94 FAMILY 19.4.2 PWM DUTY CYCLE The PWM duty cycle is specified, to use CCP4 as an example, by writing to the CCPR4L register and to the CCP4CON bits. Up to 10-bit resolution is available. The CCPR4L contains the eight MSbs and the CCP4CON contains the two LSbs. This 10-bit value is represented by CCPR4L:CCP4CON. The following equation is used to calculate the PWM duty cycle in time: EQUATION 19-2: PWM DUTY CYCLE (IN TIME) The maximum PWM resolution (bits) for a given PWM frequency is given by the equation: PWM RESOLUTION PWM Resolution (max) CCPR4L and CCP4CON can be written to at any time, but the duty cycle value is not latched into CCPR4H until after a match between PR2 and TMR2 occurs (that is, the period is complete). In PWM mode, CCPR4H is a read-only register. Note: F OSC log  ----------------  F PWM = ------------------------------bits log  2  If the PWM duty cycle value is longer than the PWM period, the CCP4 pin will not be cleared. EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 40 MHz PWM Frequency Timer Prescaler (1, 4, 16) PR2 Value Maximum Resolution (bits) 19.4.3 When the CCPR4H and two-bit latch match TMR2, concatenated with an internal two-bit Q clock or two bits of the TMR2 prescaler, the CCP4 pin is cleared. EQUATION 19-3: PWM Duty Cycle = (CCPR4L:CCP4CON) • TOSC • (TMR2 Prescale Value) TABLE 19-4: The CCPR4H register and a two-bit internal latch are used to double-buffer the PWM duty cycle. This double-buffering is essential for glitchless PWM operation. 2.44 kHz 9.77 kHz 39.06 kHz 156.25 kHz 312.50 kHz 416.67 kHz 16 4 1 1 1 1 FFh FFh FFh 3Fh 1Fh 17h 10 10 10 8 7 6.58 SETUP FOR PWM OPERATION To configure the CCP module for PWM operation using CCP4 as an example: 1. 2. 3. 4. 5. Set the PWM period by writing to the PR2 register. Set the PWM duty cycle by writing to the CCPR4L register and CCP4CON bits. Make the CCP4 pin an output by clearing the appropriate TRIS bit. Set the TMR2 prescale value, then enable Timer2 by writing to T2CON. Configure the CCP4 module for PWM operation. DS30000575C-page 346  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 20.0 20.1 MASTER SYNCHRONOUS SERIAL PORT (MSSP) MODULE Master SSP (MSSP) Module Overview The Master Synchronous Serial Port (MSSP) module is a serial interface, useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be serial EEPROMs, shift registers, display drivers, A/D Converters, etc. The MSSP module can operate in one of two modes: • Serial Peripheral Interface (SPI) • Inter-Integrated Circuit™ (I2C) - Full Master mode - Slave mode (with general address call) 20.2 Each MSSP module has four associated control registers. These include a STATUS register (SSPxSTAT) and three control registers (SSPxCON1, SSPxCON2, and SSPxCON3). The use of these registers and their individual Configuration bits differ significantly depending on whether the MSSP module is operated in SPI or I2C mode. Additional details are provided under the individual sections. On all PIC18F97J94 family devices, the SPI DMA capability can only be used in conjunction with MSSP1. The SPI DMA feature is described in Section 20.4 “SPI DMA Module”. Note: In devices with more than one MSSP module, it is very important to pay close attention to SSPxCON register names. SSP1CON1 and SSP1CON2 control different operational aspects of the same module, while SSP1CON1 and SSP2CON1 control the same features for two different modules. Note: The SSPxBUF register cannot be used with read-modify-write instructions, such as BCF, COMF, etc. The I2C interface supports the following modes in hardware: • Master mode • Multi-Master mode • Slave mode with 5-bit and 7-bit address masking (with address masking for both 10-bit and 7-bit addressing) All members of the PIC18FXXJ94 have two MSSP modules, designated as MSSP1 and MSSP2. Each module operates independently of the other. Note: Throughout this section, generic references to an MSSP module in any of its operating modes may be interpreted as being equally applicable to MSSP1 or MSSP2. Register names and module I/O signals use the generic designator ‘x’ to indicate the use of a numeral to distinguish a particular module when required. Control bit names are not individuated.  2012-2016 Microchip Technology Inc. Control Registers To avoid lost data in Master mode, a read of the SSPxBUF must be performed to clear the Buffer Full (BF) detect bit (SSPSTAT) between each transmission. DS30000575C-page 347 PIC18F97J94 FAMILY 20.3 SPI Mode FIGURE 20-1: The SPI mode allows 8 bits of data to be synchronously transmitted and received simultaneously. All four modes of SPI are supported. To accomplish communication, three pins are typically used. These pins must be assigned through the PPS-Lite Configuration registers before use. • Serial Data Out (SDOx) – Mapped to pin using PPS-Lite Peripheral Output registers • Serial Data In (SDIx) – Mapped to pin using PPS-Lite Peripheral Input registers • Serial Clock (SCKx) – Mapped to pin using PPS-Lite Peripheral Input registers (for Slave mode) or Peripheral Output registers (for Master mode). MSSPx BLOCK DIAGRAM (SPI MODE) Internal Data Bus Read Write SSPxBUF reg SDIx SSPxSR reg Shift Clock SDOx bit 0 SSx SSx Control Enable Additionally, a fourth pin may be used when in a Slave mode of operation: Edge Select • Slave Select (SSx) – Mapped through PPS-Lite Peripheral Input registers 2 Figure 20-1 shows the block diagram of the MSSPx module when operating in SPI mode. Clock Select SCKx SSPM SMP:CKE 4 (TMR22Output) 2 Edge Select Prescaler TOSC 4, 16, 64 Data to TXx/RXx in SSPxSR TRIS bit Note: DS30000575C-page 348 PPS-Lite signal names are used in this diagram for the sake of brevity. Refer to the text for a full list of multiplexed functions.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 20.3.1 REGISTERS Each MSSP module has four registers for SPI mode operation. These are: • • • • MSSPx Control Register 1 (SSPxCON1) MSSPx STATUS Register (SSPxSTAT) MSSPx Control Register 3 (SSPxCON3) Serial Receive/Transmit Buffer Register (SSPxBUF) • MSSPx Shift Register (SSPxSR) – Not directly accessible SSPxSR is the shift register used for shifting data in or out. SSPxBUF is the buffer register to which data bytes are written to or read from. In receive operations, SSPxSR and SSPxBUF together, create a double-buffered receiver. When SSPxSR receives a complete byte, it is transferred to SSPxBUF and the SSPxIF interrupt is set. During transmission, the SSPxBUF is not doublebuffered. A write to SSPxBUF will write to both SSPxBUF and SSPxSR. SSPxCON1, SSPxCON3 and SSPxSTAT are the control and STATUS registers in SPI mode operation. The SSPxCON1 and SSPxCON3 registers are readable and writable. The lower 6 bits of the SSPxSTAT are read-only. The upper two bits of the SSPxSTAT are read/write. REGISTER 20-1: R/W-0 SMP SSPxSTAT: MSSPx STATUS REGISTER (SPI MODE) R/W-0 R-0 R-0 R-0 R-0 R-0 R-0 (1) D/A P S R/W UA BF CKE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 SMP: Sample bit SPI Master mode: 1 = Input data is sampled at the end of data output time 0 = Input data is sampled at the middle of data output time SPI Slave mode: SMP must be cleared when SPI is used in Slave mode. bit 6 CKE: SPI Clock Select bit(1) 1 = Transmit occurs on the transition from active to Idle clock state 0 = Transmit occurs on the transition from Idle to active clock state bit 5 D/A: Data/Address bit Used in I2C mode only. bit 4 P: Stop bit Used in I2C mode only. This bit is cleared when the MSSPx module is disabled; SSPEN is cleared. bit 3 S: Start bit Used in I2C mode only. bit 2 R/W: Read/Write Information bit Used in I2C mode only. bit 1 UA: Update Address bit Used in I2C mode only. bit 0 BF: Buffer Full Status bit (Receive mode only) 1 = Receive is complete, SSPxBUF is full 0 = Receive is not complete, SSPxBUF is empty Note 1: Polarity of clock state is set by the CKP bit (SSPxCON1).  2012-2016 Microchip Technology Inc. DS30000575C-page 349 PIC18F97J94 FAMILY REGISTER 20-2: SSPxCON1: MSSPx CONTROL REGISTER 1 (SPI MODE) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 WCOL SSPOV(1) SSPEN(2) CKP SSPM3(4) SSPM2(4) SSPM1(4) SSPM0(4) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 WCOL: Write Collision Detect bit 1 = The SSPxBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision bit 6 SSPOV: Receive Overflow Indicator bit(1) SPI Slave mode: 1 = A new byte is received while the SSPxBUF register is still holding the previous data. In case of overflow, the data in SSPxSR is lost. Overflow can only occur in Slave mode. The user must read the SSPxBUF, even if only transmitting data, to avoid setting overflow (must be cleared in software). 0 = No overflow bit 5 SSPEN: Master Synchronous Serial Port Enable bit(2) 1 = Enables serial port and configures SCKx, SDOx, SDIx and SSx as serial port pins 0 = Disables serial port and configures these pins as I/O port pins bit 4 CKP: Clock Polarity Select bit 1 = Idle state for the clock is a high level 0 = Idle state for the clock is a low level bit 3-0 SSPM: Master Synchronous Serial Port Mode Select bits(4) 1010 = SPI Master mode: Clock = FOSC/(4 * (SSPxADD + 1)(3) 0101 = SPI Slave mode: Clock = SCKx pin; SSx pin control is disabled; SSx can be used as I/O pin 0100 = SPI Slave mode: Clock = SCKx pin; SSx pin control is enabled 0011 = SPI Master mode: Clock = TMR2 output/2 0010 = SPI Master mode: Clock = FOSC/64 0001 = SPI Master mode: Clock = FOSC/16 0000 = SPI Master mode: Clock = FOSC/4 Note 1: 2: 3: 4: In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPxBUF register. When enabled, these pins must be properly configured as inputs or outputs. SSPxADD = 0 is not supported. Bit combinations not specifically listed here are either reserved or implemented in I2C mode only. DS30000575C-page 350  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 20-3: SSPxCON3: MSSP CONTROL REGISTER 3 (SPI MODE) R/HS/HC-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 ACKTIM: Acknowledge Time Status bit Unused in SPI. bit 6 PCIE: Stop Condition Interrupt Enable bit(1) 1 = Enable interrupt on detection of Stop condition 0 = Stop detection interrupts are disabled bit 5 SCIE: Start Condition Interrupt Enable bit(1) 1 = Enable interrupt on detection of Start or Restart conditions 0 = Start detection interrupts are disabled bit 4 BOEN: Buffer Overwrite Enable bit(2) 1 = SSPBUF updates every time a new data byte is shifted in, ignoring the BF bit 0 = If a new byte is received with BF bit already set, SSPOV is set, and the buffer is not updated bit 3 SDAHT: SDA Hold Time Selection bit Unused in SPI. bit 2 SBCDE: Slave Mode Bus Collision Detect Enable bit Unused in SPI. bit 1 AHEN: Address Hold Enable bit Unused in SPI. bit 0 DHEN: Data Hold Enable bit Unused in SPI. Note 1: 2: This bit has no effect in Slave modes that Start and Stop condition detection is explicitly listed as enabled. For daisy-chained SPI operation; allows the user to ignore all but the last received byte. SSPOV is still set when a new byte is received and BF = 1, but hardware continues to write the most recent byte to SSPxBUF.  2012-2016 Microchip Technology Inc. DS30000575C-page 351 PIC18F97J94 FAMILY 20.3.2 OPERATION When initializing the SPI, several options need to be specified. This is done by programming the appropriate control bits (SSPxCON1 and SSPxSTAT). These control bits allow the following to be specified: • I/O pins must be mapped to the SPI peripheral in order to function. See Section 11.15 “PPS-Lite” for an explanation of the PPS-Lite mapping feature. • Master mode (SCKx is the clock output) • Slave mode (SCKx is the clock input) • Clock Polarity (Idle state of SCKx) • Data Input Sample Phase (middle or end of data output time) • Clock Edge (output data on rising/falling edge of SCKx) • Clock Rate (Master mode only) • Slave Select mode (Slave mode only) Each MSSPx module consists of a Transmit/Receive Shift register (SSPxSR) and a Buffer register (SSPxBUF). The SSPxSR shifts the data in and out of the device, MSb first. The SSPxBUF holds the data that was written to the SSPxSR until the received data is ready. Once the 8 bits of data have been received, that byte is moved to the SSPxBUF register. Then, the Buffer Full detect bit, BF (SSPxSTAT), and the interrupt flag bit, SSPxIF, are set. This double-buffering of the received data (SSPxBUF) allows the next byte to start reception before reading the data that was just received. Any write to the SSPxBUF register during transmission/reception of data will be ignored and the Write Collision Detect bit, WCOL (SSPxCON1), will be set. User software must clear the WCOL bit so that it can be determined if the following write(s) to the SSPxBUF register completed successfully. EXAMPLE 20-1: LOOP When the application software is expecting to receive valid data, the SSPxBUF should be read before the next byte of data to transfer is written to the SSPxBUF. The Buffer Full bit, BF (SSPxSTAT), indicates when SSPxBUF has been loaded with the received data (transmission is complete). When the SSPxBUF is read, the BF bit is cleared. This data may be irrelevant if the SPI is only a transmitter. Generally, the MSSPx interrupt is used to determine when the transmission/ reception has completed. If the interrupt method is not going to be used, then software polling can be done to ensure that a write collision does not occur. Example 20-1 shows the loading of the SSPxBUF (SSPxSR) for data transmission. The SSPxSR is not directly readable or writable and can only be accessed by addressing the SSPxBUF register. Additionally, the SSPxSTAT register indicates the various status conditions. 20.3.3 OPEN-DRAIN OUTPUT OPTION The drivers for the SDOx output and SCKx clock pins can be optionally configured as open-drain outputs. This feature allows the voltage level on the pin to be pulled to a higher level through an external pull-up resistor, and allows the output to communicate with external circuits without the need for additional level shifters. For more information, see Section 11.1.3 “Open-Drain Outputs”. The open-drain output option is controlled by the SSPxOD bits (ODCON1). Setting an SSPxOD bit configures the SDOx and SCKx pins for the corresponding module for open-drain operation. Note: To avoid lost data in Master mode, a read of the SSPxBUF must be performed to clear the Buffer Full (BF) detect bit (SSPxSTAT) between each transmission. LOADING THE SSP1BUF (SSP1SR) REGISTER BTFSS BRA MOVF SSP1STAT, BF LOOP SSP1BUF, W MOVWF RXDATA ;Save in user RAM, if data is meaningful MOVF MOVWF TXDATA, W SSP1BUF ;W reg = contents of TXDATA ;New data to xmit DS30000575C-page 352 ;Has data been received (transmit complete)? ;No ;WREG reg = contents of SSP1BUF  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 20.3.4 ENABLING SPI I/O 20.3.5 TYPICAL CONNECTION To enable the serial port, the peripheral must first be mapped to I/O pins using the PPS-Lite feature. To enable the SPI peripheral, the MSSPx Enable bit, SSPEN (SSPxCON1) must be set. To reset or reconfigure SPI mode, clear the SSPEN bit, re-initialize the SSPxCON registers and then set the SSPEN bit. This configures the SDIx, SDOx, SCKx and SSx pins as serial port pins. For the pins to behave as the serial port function, some must have their data direction bits (in the TRIS register) appropriately programmed as follows: Figure 20-2 shows a typical connection between two microcontrollers. The master controller (Processor 1) initiates the data transfer by sending the SCKx signal. Data is shifted out of both shift registers on their programmed clock edge and latched on the opposite edge of the clock. Both processors should be programmed to the same Clock Polarity (CKP), then both controllers would send and receive data at the same time. Whether the data is meaningful (or dummy data) depends on the application software. This leads to three scenarios for data transmission: • SDIx is automatically controlled by the SPI module • SDOx must have the TRIS bit cleared for the corresponding RPn pin. • SCKx (Master mode) must have the TRIS bit cleared for the corresponding RPn pin • SCKx (Slave mode) must have the TRIS bit set for the corresponding RPn pin • SSx must have the TRIS bit set for the corresponding RPn pin. • Master sends data–Slave sends dummy data • Master sends data–Slave sends data • Master sends dummy data–Slave sends data Any serial port function that is not desired may be overridden by programming the corresponding Data Direction (TRIS) register to the opposite value. FIGURE 20-2: SPI MASTER/SLAVE CONNECTION SPI Master SSPM = 00xxb SPI Slave SSPM = 010xb SDOx SDIx Serial Input Buffer (SSPxBUF) SDIx Shift Register (SSPxSR) MSb Serial Input Buffer (SSPxBUF) SDOx LSb MSb SCKx PROCESSOR 1  2012-2016 Microchip Technology Inc. Shift Register (SSPxSR) Serial Clock LSb SCKx PROCESSOR 2 DS30000575C-page 353 PIC18F97J94 FAMILY 20.3.6 MASTER MODE The master can initiate the data transfer at any time because it controls the SCKx signal. The master determines when the slave (Processor 2, Figure 20-2) is to broadcast data by the software protocol. In Master mode, the data is transmitted/received as soon as the SSPxBUF register is written to. If the SPI is only going to receive, the SDOx output could be disabled (programmed as an input). The SSPxSR register will continue to shift in the signal present on the SDIx pin at the programmed clock rate. As each byte is received, it will be loaded into the SSPxBUF register as if a normal received byte (interrupts and Status bits appropriately set). This could be useful in receiver applications as a “Line Activity Monitor” mode. The clock polarity is selected by appropriately programming the CKP bit (SSPxCON1). This, then, would give waveforms for SPI communication, as shown in Figure 20-3, Figure 20-5 and Figure 20-6, where the FIGURE 20-3: MSB is transmitted first. In Master mode, the SPI clock rate (bit rate) is user-programmable to be one of the following: • • • • • FOSC/4 (or TCY) FOSC/(4 * (SSPxADD + 1) FOSC/16 (or 4 • TCY) FOSC/64 (or 16 • TCY) Timer2 output/2 This allows a maximum data rate (at 64 MHz) of 16.00 Mbps. Figure 20-3 shows the waveforms for Master mode. When the CKE bit is set, the SDOx data is valid before there is a clock edge on SCKx. The change of the input sample is shown based on the state of the SMP bit. The time when the SSPxBUF is loaded with the received data is shown. SPI MODE WAVEFORM (MASTER MODE) Write to SSPxBUF SCKx (CKP = 0 CKE = 0) SCKx (CKP = 1 CKE = 0) 4 Clock Modes SCKx (CKP = 0 CKE = 1) SCKx (CKP = 1 CKE = 1) SDOx (CKE = 0) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SDOx (CKE = 1) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SDIx (SMP = 0) bit 0 bit 7 Input Sample (SMP = 0) SDIx (SMP = 1) bit 7 bit 0 Input Sample (SMP = 1) SSPxIF SSPxSR to SSPxBUF DS30000575C-page 354 Next Q4 Cycle after Q2  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 20.3.7 SLAVE MODE In Slave mode, the data is transmitted and received as the external clock pulses appear on SCKx. When the last bit is latched, the SSPxIF interrupt flag bit is set. transmitted byte and becomes a floating output. External pull-up/pull-down resistors may be desirable depending on the application. While in Slave mode, the external clock is supplied by the external clock source on the SCKx pin. This external clock must meet the minimum high and low times as specified in the electrical specifications. When the SPI is in Slave mode with pin control enabled SSx (SSPxCON1 = 0100), the SPI module will reset if the SSx pin is set to VDD. While in Sleep mode, the slave can transmit/receive data. When a byte is received, the device can be configured to wake-up from Sleep. If the SPI is used in Slave mode with CKE set, then the SSx pin control must be enabled. 20.3.8 When the SPI module resets, the bit counter is forced to ‘0’. This can be done by either forcing the SSx pin to a high level or clearing the SSPEN bit. SLAVE SELECT SYNCHRONIZATION The SSx pin allows a Synchronous Slave mode. The SPI must be in Slave mode with the SSx pin control enabled (SSPxCON1 = 04h). When the SSx pin is low, transmission and reception are enabled and the SDOx pin is driven. When the SSx pin goes high, the SDOx pin is no longer driven, even if in the middle of a FIGURE 20-4: Note: To emulate two-wire communication, the SDOx pin can be connected to the SDIx pin. When the SPI needs to operate as a receiver, the SDOx pin can be configured as an input. This disables transmissions from the SDOx. The SDIx can always be left as an input (SDIx function) since it cannot create a bus conflict. SLAVE SYNCHRONIZATION WAVEFORM SSx SCKx (CKP = 0 CKE = 0) SCKx (CKP = 1 CKE = 0) Write to SSPxBUF SDOx SDIx (SMP = 0) bit 7 bit 6 bit 7 bit 0 bit 0 bit 7 bit 7 Input Sample (SMP = 0) SSPxIF Interrupt Flag SSPxSR to SSPxBUF  2012-2016 Microchip Technology Inc. Next Q4 Cycle after Q2 DS30000575C-page 355 PIC18F97J94 FAMILY FIGURE 20-5: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 0) SSx Optional SCKx (CKP = 0 CKE = 0) SCKx (CKP = 1 CKE = 0) Write to SSPxBUF SDOx SDIx (SMP = 0) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 bit 0 bit 7 Input Sample (SMP = 0) SSPxIF Interrupt Flag Next Q4 Cycle after Q2 SSPxSR to SSPxBUF FIGURE 20-6: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 1) SSx Not Optional SCKx (CKP = 0 CKE = 1) SCKx (CKP = 1 CKE = 1) Write to SSPxBUF SDOx SDIx (SMP = 0) bit 7 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 bit 0 Input Sample (SMP = 0) SSPxIF Interrupt Flag SSPxSR to SSPxBUF DS30000575C-page 356 Next Q4 Cycle after Q2  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 20.3.9 OPERATION IN POWER-MANAGED MODES In SPI Master mode, module clocks may be operating at a different speed than when in full-power mode. In the case of Sleep mode, all clocks are halted. In Idle modes, a clock is provided to the peripherals. That clock can be from the primary clock source, the secondary clock (SOSC Oscillator) or the INTOSC source. 20.3.11 Table 20-1 shows the compatibility between the standard SPI modes and the states of the CKP and CKE control bits. TABLE 20-1: If the Sleep mode is selected, all module clocks are halted and the transmission/reception will remain in that state until the device wakes. After the device returns to Run mode, the module will resume transmitting and receiving data. In SPI Slave mode, the SPI Transmit/Receive Shift register operates asynchronously to the device. This allows the device to be placed in any power-managed mode and data to be shifted into the SPI Transmit/ Receive Shift register. When all 8 bits have been received, the MSSPx interrupt flag bit will be set, and if enabled, will wake the device. 20.3.10 EFFECTS OF A RESET SPI BUS MODES Control Bits State Standard SPI Mode Terminology CKP CKE 0, 0 0 1 0, 1 0 0 1, 0 1 1 1, 1 1 0 In most cases, the speed that the master clocks SPI data is not important; however, this should be evaluated for each system. If MSSPx interrupts are enabled, they can wake the controller from Sleep mode, or one of the Idle modes, when the master completes sending data. If an exit from Sleep or Idle mode is not desired, MSSPx interrupts should be disabled. BUS MODE COMPATIBILITY There is also an SMP bit which controls when the data is sampled. 20.3.12 SPI CLOCK SPEED AND MODULE INTERACTIONS Because MSSP1 and MSSP2 are independent modules, they can operate simultaneously at different data rates. Setting the SSPM bits of the SSPxCON1 register determines the rate for the corresponding module. An exception is when both modules use Timer2 as a time base in Master mode. In this instance, any changes to the Timer2 module’s operation will affect both MSSPx modules equally. If different bit rates are required for each module, the user should select one of the other three time base options for one of the modules. A Reset disables the MSSPx module and terminates the current transfer.  2012-2016 Microchip Technology Inc. DS30000575C-page 357 PIC18F97J94 FAMILY 20.4 SPI DMA MODULE The SPI DMA module contains control logic to allow the MSSP1 module to perform SPI Direct Memory Access transfers. This enables the module to quickly transmit or receive large amounts of data with relatively little CPU intervention. When the SPI DMA module is used, MSSP1 can directly read and write to general purpose SRAM. When the SPI DMA module is not enabled, MSSP1 functions normally, but without DMA capability. The SPI DMA module is composed of control logic, a Destination Receive Address Pointer, a Transmit Source Address Pointer, an interrupt manager and a Byte Count register for setting the size of each DMA transfer. The DMA module may be used with all SPI Master and Slave modes, and supports both half-duplex and full-duplex transfers. 20.4.1 I/O PIN CONSIDERATIONS When enabled, the SPI DMA module uses the MSSP1 module. All SPI input and output signals, related to MSSP1, are routed through the Peripheral Pin Select (PPS) module. The appropriate initialization procedure, as described in Section 20.4.6 “Using the SPI DMA Module”, will need to be followed prior to using the SPI DMA module. The output pins assigned to the SDO and SCK functions can optionally be configured as open-drain outputs, such as for level shifting operations mentioned in the same section. 20.4.2 RAM TO RAM COPY OPERATIONS Although the SPI DMA module is primarily intended to be used for SPI communication purposes, the module can also be used to perform RAM to RAM copy operations. To do this, configure the module for Full-Duplex Master mode operation, but assign the SDO output and SDI input functions onto the same RPn pin in the PPSLite module. Also assign SCK out and SCK in onto the same RPn pin (a different pin than used for SDO and SDI). This will allow the module to operate in Loopback mode, providing RAM copy capability. DS30000575C-page 358 20.4.3 IDLE AND SLEEP CONSIDERATIONS The SPI DMA module remains fully functional when the microcontroller is in Idle mode. During normal Sleep, the SPI DMA module is not functional and should not be used. To avoid corrupting a transfer, user firmware should be careful to make certain that pending DMA operations are complete by polling the DMAEN bit in the DMACON1 register, prior to putting the microcontroller into Sleep. In SPI Slave modes, the MSSP1 module is capable of transmitting and/or receiving one byte of data while in Sleep mode. This allows the SSP1IF flag in the PIR1 register to be used as a wake-up source. When the DMAEN bit is cleared, the SPI DMA module is effectively disabled, and the MSSP1 module functions normally, but without DMA capabilities. If the DMAEN bit is clear prior to entering Sleep, it is still possible to use the SSP1IF as a wake-up source without any data loss. Neither MSSP1 nor the SPI DMA module will provide any functionality in Deep Sleep. Upon exiting from Deep Sleep, all of the I/O pins, MSSP1 and SPI DMA related registers will need to be fully re-initialized before the SPI DMA module can be used again. 20.4.4 REGISTERS The SPI DMA engine is enabled and controlled by the following Special Function Registers: • DMACON1 • DMACON2 • TXADDRH • TXADDRL • RXADDRH • RXADDRL • DMABCH • DMABCL  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 20.4.4.1 DMACON1 The DMACON1 register is used to select the main operating mode of the SPI DMA module. The SSCON1 and SSCON0 bits are used to control the slave select pin. When MSSP1 is used in SPI Master mode with the SPI DMA module, SSDMA can be controlled by the DMA module as an output pin. If MSSP1 will be used to communicate with an SPI slave device that needs the SSx pin to be toggled periodically, the SPI DMA hardware can automatically be used to de-assert SSx between each byte, every two bytes or every four bytes. Alternatively, user firmware can manually generate slave select signals with normal general purpose I/O pins, if required by the slave device(s). When the TXINC bit is set, the TXADDR register will automatically increment after each transmitted byte. Automatic transmit address increment can be disabled by clearing the TXINC bit. If the automatic transmit address increment is disabled, each byte which is output on SDO will be the same (the contents of the SRAM pointed to by the TXADDR register) for the entire DMA transaction. When the RXINC bit is set, the RXADDR register will automatically increment after each received byte. Automatic receive address increment can be disabled by clearing the RXINC bit. If RXINC is disabled in FullDuplex or Half-Duplex Receive modes, all incoming data bytes on SDI will overwrite the same memory location pointed to by the RXADDR register. After the SPI DMA transaction has completed, the last received byte will reside in the memory location pointed to by the RXADDR register. The SPI DMA module can be used for either half-duplex receive only communication, half-duplex transmit only communication or full-duplex simultaneous transmit and receive operations. All modes are available for both SPI master and SPI slave configurations. The DUPLEX0 and DUPLEX1 bits can be used to select the desired operating mode. The behavior of the DLYINTEN bit varies greatly depending on the SPI operating mode. For example behavior for each of the modes, see Figure 20-3 through Figure 20-6. SPI Slave mode, DLYINTEN = 1: In this mode, an SSP1IF interrupt will be generated during a transfer if the time between successful byte transmission events is longer than the value set by the DLYCYC bits in the DMACON2 register. This interrupt allows slave firmware to know that the master device is taking an unusually large amount of time between byte transmissions. For example, this information may be useful for implementing application defined communication protocols, involving time-outs if the bus remains Idle for  2012-2016 Microchip Technology Inc. too long. When DLYINTEN = 1, the DLYLVL interrupts occur normally according to the selected setting. SPI Slave mode, DLYINTEN = 0: In this mode, the time-out based interrupt is disabled. No additional SSP1IF interrupt events will be generated by the SPI DMA module, other than those indicated by the INTLVL bits in the DMACON2 register. In this mode, always set DLYCYC = 0000. SPI Master mode, DLYINTEN = 0: The DLYCYC bits in the DMACON2 register determine the amount of additional inter-byte delay, which is added by the SPI DMA module during a transfer; the Master mode SS1 output feature may be used. SPI Master mode, DLYINTEN = 1: The amount of hardware overhead is slightly reduced in this mode, and the minimum inter-byte delay is 8 TCY for FOSC/4, 9 TCY for FOSC/16 and 15 TCY for FOSC/64. This mode can potentially be used to obtain slightly higher effective SPI bandwidth. In this mode, the SS1 control feature cannot be used and should always be disabled (DMACON1 = 00). Additionally, the interrupt generating hardware (used in Slave mode) remains active. To avoid extraneous SSP1IF interrupt events, set the DMACON2 Delay bits, DLYCYC = 1111, and ensure that the SPI serial clock rate is no slower than FOSC/64. In SPI Master modes, the DMAEN bit is used to enable the SPI DMA module and to initiate an SPI DMA transaction. After user firmware sets the DMAEN bit, the DMA hardware will begin transmitting and/or receiving data bytes according to the configuration used. In SPI Slave modes, setting the DMAEN bit will finish the initialization steps needed to prepare the SPI DMA module for communication (which must still be initiated by the master device). To avoid possible data corruption, once the DMAEN bit is set, user firmware should not attempt to modify any of the MSSP2 or SPI DMA related registers, with the exception of the INTLVLx bits in the DMACON2 register. If user firmware wants to halt an ongoing DMA transaction, the DMAEN bit can be manually cleared by the firmware. Clearing the DMAEN bit while a byte is currently being transmitted will not immediately halt the byte in progress. Instead, any byte currently in progress will be completed before the MSSP1 and SPI DMA modules go back to their Idle conditions. If user firmware clears the DMAEN bit, the TXADDR, RXADDR and DMABC registers will no longer update, and the DMA module will no longer make any additional read or writes to SRAM; therefore, state information can be lost. DS30000575C-page 359 PIC18F97J94 FAMILY REGISTER 20-4: DMACON1: DMA CONTROL REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SSCON1 SSCON0 TXINC RXINC DUPLEX1 DUPLEX0 DLYINTEN DMAEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 SSCON: SSDMA Output Control bits (Master modes only) 11 = SSDMA is asserted for the duration of 4 bytes; DLYINTEN is always reset low 01 = SSDMA is asserted for the duration of 2 bytes; DLYINTEN is always reset low 10 = SSDMA is asserted for the duration of 1 byte; DLYINTEN is always reset low 00 = SSDMA is not controlled by the DMA module; DLYINTEN bit is software programmable bit 5 TXINC: Transmit Address Increment Enable bit Allows the transmit address to increment as the transfer progresses. 1 = The transmit address is to be incremented from the initial value of TXADDR 0 = The transmit address is always set to the initial value of TXADDR bit 4 RXINC: Receive Address Increment Enable bit Allows the receive address to increment as the transfer progresses. 1 = The received address is to be incremented from the initial value of RXADDR 0 = The received address is always set to the initial value of RXADDR bit 3-2 DUPLEX: Transmit/Receive Operating Mode Select bits 10 = SPI DMA operates in Full-Duplex mode, data is simultaneously transmitted and received 01 = DMA operates in Half-Duplex mode, data is transmitted only 00 = DMA operates in Half-Duplex mode, data is received only bit 1 DLYINTEN: Delay Interrupt Enable bit Enables the interrupt to be invoked after the number of TCY cycles, specified in DLYCYC, has elapsed from the latest completed transfer. 1 = The interrupt is enabled, SSCON must be set to ‘00’ 0 = The interrupt is disabled bit 0 DMAEN: DMA Operation Start/Stop bit This bit is set by the users’ software to start the DMA operation. It is reset back to zero by the DMA engine when the DMA operation is completed or aborted. 1 = DMA is in session 0 = DMA is not in session DS30000575C-page 360  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 20.4.4.2 DMACON2 The DMACON2 register contains control bits for controlling interrupt generation and inter-byte delay behavior. The INTLVL bits are used to select when an SSP1IF interrupt should be generated. The function of the DLYCYC bits depends on the SPI operating mode (Master/Slave), as well as the DLYINTEN setting. In SPI Master mode, the REGISTER 20-5: DLYCYC bits can be used to control how much time the module will Idle between bytes in a transfer. By default, the hardware requires a minimum delay of 8 TCY for FOSC/4, 9 TCY for FOSC/16 and 15 TCY for FOSC/64. An additional delay can be added with the DLYCYCx bits. In SPI Slave modes, the DLYCYC bits may optionally be used to trigger an additional time-out based interrupt. DMACON2: DMA CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DLYCYC3 DLYCYC2 DLYCYC1 DLYCYC0 INTLVL3 INTLVL2 INTLVL1 INTLVL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-4 x = Bit is unknown DLYCYC: Delay Cycle Selection bits When DLYINTEN = 0, these bits specify the additional delay (above the base overhead of the hardware), in number of TCY cycles, before the SSP2BUF register is written again for the next transfer. When DLYINTEN = 1, these bits specify the delay in number of TCY cycles from the latest completed transfer before an interrupt to the CPU is invoked. In this case, the additional delay before the SSP2BUF register is written again is 1 TCY + (base overhead of hardware). 1111 = Delay time in number of instruction cycles is 2,048 cycles 1110 = Delay time in number of instruction cycles is 1,024 cycles 1101 = Delay time in number of instruction cycles is 896 cycles 1100 = Delay time in number of instruction cycles is 768 cycles 1011 = Delay time in number of instruction cycles is 640 cycles 1010 = Delay time in number of instruction cycles is 512 cycles 1001 = Delay time in number of instruction cycles is 384 cycles 1000 = Delay time in number of instruction cycles is 256 cycles 0111 = Delay time in number of instruction cycles is 128 cycles 0110 = Delay time in number of instruction cycles is 64 cycles 0101 = Delay time in number of instruction cycles is 32 cycles 0100 = Delay time in number of instruction cycles is 16 cycles 0011 = Delay time in number of instruction cycles is 8 cycles 0010 = Delay time in number of instruction cycles is 4 cycles 0001 = Delay time in number of instruction cycles is 2 cycles 0000 = Delay time in number of instruction cycles is 1 cycle  2012-2016 Microchip Technology Inc. DS30000575C-page 361 PIC18F97J94 FAMILY REGISTER 20-5: bit 3-0 DMACON2: DMA CONTROL REGISTER 2 (CONTINUED) INTLVL: Watermark Interrupt Enable bits These bits specify the amount of remaining data yet to be transferred (transmitted and/or received) upon which an interrupt is generated. 1111 = Amount of remaining data to be transferred is 576 bytes 1110 = Amount of remaining data to be transferred is 512 bytes 1101 = Amount of remaining data to be transferred is 448 bytes 1100 = Amount of remaining data to be transferred is 384 bytes 1011 = Amount of remaining data to be transferred is 320 bytes 1010 = Amount of remaining data to be transferred is 256 bytes 1001 = Amount of remaining data to be transferred is 192 bytes 1000 = Amount of remaining data to be transferred is 128 bytes 0111 = Amount of remaining data to be transferred is 67 bytes 0110 = Amount of remaining data to be transferred is 32 bytes 0101 = Amount of remaining data to be transferred is 16 bytes 0100 = Amount of remaining data to be transferred is 8 bytes 0011 = Amount of remaining data to be transferred is 4 bytes 0010 = Amount of remaining data to be transferred is 2 bytes 0001 = Amount of remaining data to be transferred is 1 byte 0000 = Transfer complete DS30000575C-page 362  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 20.4.4.3 DMABCH and DMABCL The DMABCH and DMABCL register pair forms a 10-bit Byte Count register, which is used by the SPI DMA module to send/receive up to 1,024 bytes for each DMA transaction. When the DMA module is actively running (DMAEN = 1), the DMA Byte Count register decrements after each byte is transmitted/received. The DMA transaction will halt and the DMAEN bit will be automatically cleared by hardware after the last byte has completed. After a DMA transaction is complete, the DMABC register will read 0x000. Prior to initiating a DMA transaction by setting the DMAEN bit, user firmware should load the appropriate value into the DMABCH/DMABCL registers. The DMABC is a “base zero” counter, so the actual number of bytes which will be transmitted follows in Equation 20-1. DMA module cannot be used to read from the Special Function Registers (SFRs) contained in Banks 14 and 15. 20.4.4.5 RXADDRH and RXADDRL The RXADDRH and RXADDRL registers pair together to form a 12-bit Receive Destination Address Pointer. In modes that use RXADDR (Full-Duplex and HalfDuplex Receive), the RXADDR register will be incremented after each byte is received. Received data bytes will be stored at the memory location pointed to by the RXADDR register. For example, if user firmware wants to transmit 7 bytes in one transaction, DMABC should be loaded with 006h. Similarly, if user firmware wishes to transmit 1,024 bytes, DMABC should be loaded with 3FFh. EQUATION 20-1: BYTES TRANSMITTED FOR A GIVEN DMABC Bytes XMIT ½  DMABC + 1  20.4.4.4 TXADDRH and TXADDRL The TXADDRH and TXADDRL registers pair together to form a 12-bit Transmit Source Address Pointer register. In modes that use TXADDR (Full-Duplex and Half-Duplex Transmit), the TXADDR will be incremented after each byte is transmitted. Transmitted data bytes will be taken from the memory location pointed to by the TXADDR register. The contents of the memory locations pointed to by TXADDR will not be modified by the DMA module during a transmission. The SPI DMA module can read from, and transmit data from, all general purpose memory on the device, including memory used for USB endpoint buffers. The SPI  2012-2016 Microchip Technology Inc. DS30000575C-page 363 PIC18F97J94 FAMILY The SPI DMA module can write received data to all general purpose memory on the device, including memory used for USB endpoint buffers. The SPI DMA module cannot be used to modify the Special Function Registers contained in Banks 14 and 15. 20.4.5 INTERRUPTS The SPI DMA module alters the behavior of the SSP1IF interrupt flag. In normal non-DMA modes, the SSP1IF is set once after every single byte is transmitted/received through the MSSP1 module. When MSSP1 is used with the SPI DMA module, the SSP1IF interrupt flag will be set according to the user-selected INTLVL value specified in the DMACON2 register. The SSP1IF interrupt condition will also be generated once the SPI DMA transaction has fully completed and the DMAEN bit has been cleared by hardware. The SSP1IF flag becomes set once the DMA byte count value indicates that the specified INTLVLx has been reached. For example, if DMACON2 = 0101 (16 bytes remaining), the SSP1IF interrupt flag will become set once DMABC reaches 00Fh. If user firmware then clears the SSP1IF interrupt flag, the flag will not be set again by the hardware until after all bytes have been fully transmitted and the DMA transaction is complete. Note: User firmware may modify the INTLVLx bits while a DMA transaction is in progress (DMAEN = 1). If an INTLVLx value is selected which is higher than the actual remaining number of bytes (indicated by DMABC + 1), the SSP1IF interrupt flag will immediately become set. For example, if DMABC = 00Fh (implying 16 bytes are remaining) and user firmware writes ‘1111’ to INTLVL (interrupt when 576 bytes are remaining), the SSP1IF interrupt flag will immediately become set. If user firmware clears this interrupt flag, a new interrupt condition will not be generated until either: user firmware again writes INTLVLx with an interrupt level higher than the actual remaining level, or the DMA transaction completes and the DMAEN bit is cleared. Note: If the INTLVLx bits are modified while a DMA transaction is in progress, care should be taken to avoid inadvertently changing the DLYCYC value. DS30000575C-page 364  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 20.4.6 USING THE SPI DMA MODULE The following steps would typically be taken to enable and use the SPI DMA module: 1. 2. 3. Configure the I/O pins, which will be used by MSSP2: a) Assign SCK1, SDO1, SDI1 and SS1 to the RPn pins, as appropriate for the SPI mode which will be used. Only functions which will be used need to be assigned to a pin. b) Initialize the associated LATx registers for the desired Idle SPI bus state. c) If Open-Drain Output mode on SDO1 and SCK1 (Master mode) is desired, set ODCON1. d) Configure the corresponding TRISx bits for each I/O pin used. Configure and enable MSSP1 for the desired SPI operating mode: a) Select the desired operating mode (Master or Slave, SPI Mode 0, 1, 2 and 3) and configure the module by writing to the SSP1STAT and SSP1CON1 registers. b) Enable MSSP1 by setting SSP1CON1 = 1. Configure the SPI DMA engine: a) Select the desired operating mode by writing the appropriate values to DMACON2 and DMACON1. b) Initialize the TXADDRH/TXADDRL Pointer (Full-Duplex or Half-Duplex Transmit Only mode). c) Initialize the RXADDRH/RXADDRL Pointer (Full-Duplex or Half-Duplex Receive Only mode). d) Initialize the DMABCH/DMABCL Byte Count register with the number of bytes to be transferred in the next SPI DMA operation. e) Set the DMAEN bit (DMACON1). indicating the transaction is still in progress. User firmware would typically use this interrupt condition to begin preparing new data for the next DMA transaction. Firmware should not repeat Steps 3.b. through 3.e. until the DMAEN bit is cleared by the hardware, indicating the transaction is complete. Example 20-3 provides example code, demonstrating the initialization process and the steps needed to use the SPI DMA module to perform a 512-byte Full-Duplex Master mode transfer. In SPI Master modes, this will initiate a DMA transaction. In SPI Slave modes, this will complete the initialization process, and the module will now be ready to begin receiving and/or transmitting data to the master device once the master starts the transaction. 4. Detect the SSP1IF interrupt condition (PIR1 Converted Value > Threshold 1 In this case, both of the following occur: • The Compare Hit bit (CHHn) for the corresponding channel is set; the Compare Hit bit for the mirrored channel remains cleared. • If the Write Mode bits, WM (ADCON5L), are programmed to '01', the converted value is written to the buffer, replacing the lower threshold value. If WM = 10, the converted value is discarded. The changes to the result buffer and the Compare Hit register are shown in Figure 22-14.  2012-2016 Microchip Technology Inc. DS30000575C-page 467 PIC18F97J94 FAMILY FIGURE 22-13: INSIDE WINDOW COMPARISON OPERATION Before Conversion and Comparison ADC1BUF15 — ADC1BUF14 — ADC1BUF13 — ADC1BUF12 — ADC1BUF11 After Conversion and Comparison Compare Only (‘10’) Compare and Store (‘01’) ADC1BUF15 — — ADC1BUF14 — — — ADC1BUF13 — — ADC1BUF10 Threshold 2 ADC1BUF12 — — ADC1BUF9 — ADC1BUF11 — — ADC1BUF8 — ADC1BUF10 Threshold 2 Threshold 2 ADC1BUF7 — ADC1BUF9 — — ADC1BUF6 — ADC1BUF8 — — ADC1BUF5 — ADC1BUF7 — — ADC1BUF4 — ADC1BUF6 — — ADC1BUF3 — ADC1BUF5 — — ADC1BUF2 Threshold 1 ADC1BUF4 — — ADC1BUF1 — ADC1BUF3 — — ADC1BUF0 — ADC1BUF2 Threshold 1 Conversion Value ADC1BUF1 — — ADC1BUF0 — — AD1CHITL AD1CHITL 15 14 13 12 11 10 9 8 15 14 13 12 11 10 9 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 22.7.5.3 Outside Window Comparison When the Compare Mode bits CM are programmed as '11', the converter compares the sampled value to see if it falls outside of the threshold values in the buffer and mirrored channel location. Again, since the value in the mirrored channel location is always the greater value of the two thresholds, the condition is met when either: Converted Value >Threshold 2 or Threshold 1 > Converted Value In these cases, the following occurs: • The Compare Hit bit (CHHn) for the corresponding channel is set. • If the converted value is greater than Threshold 2, the CHHn bit for the mirrored channel is also set. If it is less than Threshold 1, the mirrored channel bit remains '0'. DS30000575C-page 468 • If the Write Mode bits, WM (ADCON5L), are programmed to '01': - If the converted value is above Threshold 2, the converted value is written to the mirrored channel address, replacing the upper threshold value. - If the converted value is below Threshold 1, the converted value is written to the channel address, replacing the lower threshold value. • If WM = 10, the converted value is discarded. The changes to the result buffer and the Compare Hit register are shown in Figure 22-15 (over the upper threshold) and Figure 22-16 (under the lower threshold). Note that when a Windowed Comparison mode is selected and channel mirroring is enabled, nothing prevents a conversion from another operation from being stored in the mirrored channel location. In the previous examples of windowed operation, if AN10 is included in a Threshold Detect operation, a conversion on AN10 might be tested against the upper threshold for AN2, stored in that location. This could result in the threshold value being overwritten and/or the CHH10 bit being set.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY For this reason, users must always carefully consider the allocation and use of the upper analog channels (both external and internal) when using Windowed Compare modes. Wherever possible, exclude the upper analog channels for Threshold Detect operations, and convert and test those channels in a separate routine. FIGURE 22-14: OUTSIDE WINDOW COMPARISON OPERATION (OVER THRESHOLD 2) Before Conversion and Comparison ADC1BUF15 — ADC1BUF14 — ADC1BUF13 — After Conversion and Comparison Compare Only (‘10’) Compare and Store (‘01’) ADC1BUF15 — — — ADC1BUF14 — — — ADC1BUF13 — — Threshold 2 ADC1BUF12 — — — ADC1BUF11 — — ADC1BUF8 — ADC1BUF10 Threshold 2 Conversion Value ADC1BUF7 — ADC1BUF9 — — — ADC1BUF8 — — — ADC1BUF7 — — — ADC1BUF6 — — — ADC1BUF5 — — Threshold 1 ADC1BUF4 — — — ADC1BUF3 — — — ADC1BUF2 Threshold 1 Threshold 1 ADC1BUF1 — — ADC1BUF0 — — ADC1BUF12 ADC1BUF11 ADC1BUF10 ADC1BUF9 ADC1BUF6 ADC1BUF5 ADC1BUF4 ADC1BUF3 ADC1BUF2 ADC1BUF1 ADC1BUF0 AD1CHITL AD1CHITL 15 14 13 12 11 10 9 8 15 14 13 12 11 10 9 8 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0  2012-2016 Microchip Technology Inc. DS30000575C-page 469 PIC18F97J94 FAMILY FIGURE 22-15: OUTSIDE WINDOW COMPARISON OPERATION (UNDER THRESHOLD 1) Before Conversion and Comparison ADC1BUF15 — ADC1BUF14 — ADC1BUF13 — ADC1BUF12 — ADC1BUF11 After Conversion and Comparison Compare Only (‘10’) Compare and Store (‘01’) ADC1BUF15 — — ADC1BUF14 — — — ADC1BUF13 — — ADC1BUF10 Threshold 2 ADC1BUF12 — — ADC1BUF9 — ADC1BUF11 — — ADC1BUF8 — ADC1BUF10 Threshold 2 Threshold 2 ADC1BUF7 — ADC1BUF9 — — ADC1BUF6 — ADC1BUF8 — — ADC1BUF5 — ADC1BUF7 — — ADC1BUF4 — ADC1BUF6 — — ADC1BUF3 — ADC1BUF5 — — ADC1BUF2 Threshold 1 ADC1BUF4 — — ADC1BUF1 — ADC1BUF3 — — ADC1BUF0 — ADC1BUF2 Threshold 1 Conversion Value ADC1BUF1 — — ADC1BUF0 — — AD1CHITL 22.8 22.8.1 AD1CHITL 15 14 13 12 11 10 9 8 15 14 13 12 11 10 9 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 Examples INITIALIZATION Example 22-1 shows a simple initialization code example for the A/D module. Operation in Idle mode is disabled, output data is in unsigned fractional format, and AVDD and AVSS are used for VR+ and VR-. The start of sampling, as well as the start of conversion (conversion trigger), are performed directly in software. Scanning of inputs is disabled and an interrupt occurs after every sample/convert sequence (one conversion result) with only one channel (AN0) being converted. The A/D conversion clock is TCY/2. DS30000575C-page 470 In this particular configuration, all 16 analog input pins are set up as analog inputs. It is important to note that with this A/D module, I/O pins are configured for analog or digital operation at the I/O port with the ANSn Analog Select registers. The use of these registers is described in detail in the I/O Port chapter of the specific device data sheet. This example shows one method of controlling a sample/convert sequence by manually setting and clearing the SAMP bit (ADCON1L). This method, among others, is more fully discussed in Section 22.4 “Controlling the Sampling Process” and Section 22.5 “Controlling the Conversion Process”.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY EXAMPLE 22-3: A/D INITIALIZATION CODE EXAMPLE ADCON1H = 0x22; // Configure sample clock source ADCON1L = 0x00; // and conversion trigger mode. // Unsigned Fraction format (FORM=10), // Manual conversion trigger (SSRC=0000), // Manual start of sampling (ASAM=0), // S/H in Sample (SAMP = 1) ADCON2H = 0; // Configure A/D voltage reference ADCON2L = 0; // and buffer fill modes. // Vr+ and Vr- from AVdd and AVss(PVCFG=00, NVCFG=0), // Inputs are not scanned, // Interrupt after every sample ADCON3H = 0; // Configure sample time = 1Tad, ADCON3L = 0; // A/D conversion clock as Tcy ADCHS0H = 0; // Configure input channels, ADCHS0L = 0; // S/H+ input is AN0, // S/H- input is Vr- (AVss). ADCSS0L = 0; // No inputs are scanned. ADCSS0H = 0; // No inputs are scanned. PIR1bits.ADIF = 0; // Clear A/D conversion interrupt. // Configure A/D interrupt priority bits (ADIP) here, if // required. Default priority level is high. PIE1bits.ADIE = 1; // Enable A/D conversion interrupt ADCON1Hbits.ADON = 1; // Turn on A/D ADCON1Lbits.SAMP = 1; // Start sampling the input Delay(); // Ensure the correct sampling time has elapsed // before starting conversion. ADCON1Lbits.SAMP = 0; // End A/D sampling and start conversion // Example code for A/D ISR: #pragma interrupt _ADC1Interrupt void _ADC1Interrupt(void) { PIR1bits.ADIF = 0; }  2012-2016 Microchip Technology Inc. DS30000575C-page 471 PIC18F97J94 FAMILY 22.8.2 CONVERSION SEQUENCE EXAMPLES 22.8.2.1 The following configuration examples show the A/D operation in different sampling and buffering configurations. In each example, setting the ASAM bit starts automatic sampling. A conversion trigger ends sampling and starts conversion. Sampling and Converting a Single Channel Multiple Times In this case Figure 22-16, one A/D input, AN0, will be sampled and converted. The results are stored in the ADCBUFn buffer. This process repeats 16 times until the buffer is full and then the module generates an interrupt. The entire process will then repeat. With the ALTS bit clear, only the MUX A inputs are active. The CH0SAx and CH0NAx bits are specified (AN0 - VR-) as the inputs to the Sample-and-Hold channel. All other input selection bits are unused. FIGURE 22-16: CONVERTING ONE CHANNEL 16 TIMES PER INTERRUPT Conversion Trigger TSAMP TSAMP TSAMP TSAMP A/D CLK TCONV Analog Input AN0 TCONV AN0 TCONV AN0 TCONV AN0 ASAM SAMP DONE ADC1BUF0 ADC1BUF1 ADC1BUFE ADC1BUFF AD1IF BSF AD1CON1, ASAM DS30000575C-page 472 Instruction Execution  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY EXAMPLE 22-4: CONVERTING A SINGLE CHANNEL 16 TIMES PER INTERRUPT A/D Configuration: • • • • • • Select AN0 for S/H+ Input (CH0SA = 00000) Select VR- for S/H- Input (CH0NA = 000) Configure for No Input Scan (CSCNA = 0) Use Only MUX A for Sampling (ALTS = 0) Set AD1IF on Every 16th Sample (SMPI = 01111) Configure Buffers for Single, 16-Word Results (BUFM = 0) Operational Sequence: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Sample MUX A Input AN0; Convert and Write to Buffer 0h. Sample MUX A Input AN0; Convert and Write to Buffer 1h. Sample MUX A Input AN0; Convert and Write to Buffer 2h. Sample MUX A Input AN0; Convert and Write to Buffer 3h. Sample MUX A Input AN0; Convert and Write to Buffer 4h. Sample MUX A Input AN0; Convert and Write to Buffer 5h. Sample MUX A Input AN0; Convert and Write to Buffer 6h. Sample MUX A Input AN0; Convert and Write to Buffer 7h. Sample MUX A Input AN0; Convert and Write to Buffer 8h. Sample MUX A Input AN0; Convert and Write to Buffer 9h. Sample MUX A Input AN0; Convert and Write to Buffer Ah. Sample MUX A Input AN0; Convert and Write to Buffer Bh. Sample MUX A Input AN0; Convert and Write to Buffer Ch. Sample MUX A Input AN0; Convert and Write to Buffer Dh. Sample MUX A Input AN0; Convert and Write to Buffer Eh. Sample MUX A Input AN0; Convert and Write to Buffer Fh. Set AD1IF Flag (and generate interrupt, if enabled). Repeat (1-16) After Return from Interrupt. Results Stored in Buffer (after 2 cycles): Buffer Address ADC1BUF0 ADC1BUF1 ADC1BUF2 ADC1BUF3 ADC1BUF4 ADC1BUF5 ADC1BUF6 ADC1BUF7 ADC1BUF8 ADC1BUF9 ADC1BUFA ADC1BUFB ADC1BUFC ADC1BUFD ADC1BUFE ADC1BUFF Buffer Contents at 1st AD1IF Event AN0, Sample 1 AN0, Sample 2 AN0, Sample 3 AN0, Sample 4 AN0, Sample 5 AN0, Sample 6 AN0, Sample 7 AN0, Sample 8 AN0, Sample 9 AN0, Sample 10 AN0, Sample 11 AN0, Sample 12 AN0, Sample 13 AN0, Sample 14 AN0, Sample 15 AN0, Sample 16  2012-2016 Microchip Technology Inc. Buffer Contents at 2nd AD1IF Event AN0, Sample 17 AN0, Sample 18 AN0, Sample 19 AN0, Sample 20 AN0, Sample 21 AN0, Sample 22 AN0, Sample 23 AN0, Sample 24 AN0, Sample 25 AN0, Sample 26 AN0, Sample 27 AN0, Sample 28 AN0, Sample 29 AN0, Sample 30 AN0, Sample 31 AN0, Sample 32 DS30000575C-page 473 PIC18F97J94 FAMILY 22.8.2.2 A/D Conversions While Scanning Through All Analog Inputs Other conditions are similar to those located in Section Section 22.8.2.1 “Sampling and Converting a Single Channel Multiple Times”. Figure 22-17 and Example 22-5 illustrate a typical setup, where all available analog input channels are sampled and converted. In this instance, 16 analog inputs are assumed. The set CSCNA bit specifies scanning of the A/D inputs to the S/H positive input. FIGURE 22-17: Initially, the AN0 input is sampled and converted. The result is stored in the ADCBUFn buffer. Then, the AN1 input is sampled and converted. This process of scanning the inputs repeats 16 times, until the buffer is full, and then the module generates an interrupt. The entire process will then repeat. SCANNING ALL 16 INPUTS PER SINGLE INTERRUPT Conversion Trigger TSAMP TSAMP TSAMP TSAMP A/D CLK TCONV Analog Input AN0 TCONV AN1 TCONV AN14 TCONV AN15 ASAM SAMP DONE ADC1BUF0 ADC1BUF1 ADC1BUFE ADC1BUFF AD1IF BSET AD1CON1, #ASAM DS30000575C-page 474 Instruction Execution  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY EXAMPLE 22-5: SCANNING AND CONVERTING ALL 16 CHANNELS PER SINGLE INTERRUPT A/D Configuration: • • • • • • • Select Any Channel for S/H+ Input (CH0SA = xxxxx) Select VR- for S/H- Input (CH0NA = 000) Use Only MUX A for Sampling (ALTS = 0) Configure MUX A for Input Scan (CSCNA = 1) Include All Analog Channels in Scanning (AD1CSSL = 1111 1111 1111 1111) Set AD1IF on Every 16th Sample (SMPI = 01111) Configure Buffers for Single, 16-Word Results (BUFM = 0) Operational Sequence: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Sample MUX A Input AN0; Convert and Write to Buffer 0h. Sample MUX A Input AN1; Convert and Write to Buffer 1h. Sample MUX A Input AN2; Convert and Write to Buffer 2h. Sample MUX A Input AN3; Convert and Write to Buffer 3h. Sample MUX A Input AN4; Convert and Write to Buffer 4h. Sample MUX A Input AN5; Convert and Write to Buffer 5h. Sample MUX A Input AN6; Convert and Write to Buffer 6h. Sample MUX A Input AN7; Convert and Write to Buffer 7h. Sample MUX A Input AN8; Convert and Write to Buffer 8h. Sample MUX A Input AN9; Convert and Write to Buffer 9h. Sample MUX A Input AN10; Convert and Write to Buffer Ah. Sample MUX A Input AN11; Convert and Write to Buffer Bh. Sample MUX A Input AN12; Convert and Write to Buffer Ch. Sample MUX A Input AN13; Convert and Write to Buffer Dh. Sample MUX A Input AN14; Convert and Write to Buffer Eh. Sample MUX A Input AN15; Convert and Write to Buffer Fh. Set AD1IF Flag (and generate interrupt, if enabled). Repeat (1-16) after Return from Interrupt. Results Stored in Buffer (after 2 cycles): Buffer Address ADC1BUF0 ADC1BUF1 ADC1BUF2 ADC1BUF3 ADC1BUF4 ADC1BUF5 ADC1BUF6 ADC1BUF7 ADC1BUF8 ADC1BUF9 ADC1BUF10 ADC1BUF11 ADC1BUF12 ADC1BUF13 ADC1BUF14 ADC1BUF15 Buffer Contents at 1st AD1IF Event Sample 1 (AN0, Sample 1) Sample 2 (AN1, Sample 1) Sample 3 (AN2, Sample 1) Sample 4 (AN3, Sample 1) Sample 5 (AN4, Sample 1) Sample 6 (AN5, Sample 1) Sample 7 (AN6, Sample 1) Sample 8 (AN7, Sample 1) Sample 9 (AN8, Sample 1) Sample 10 (AN9, Sample 1) Sample 11 (AN10, Sample 1) Sample 12 (AN11, Sample 1) Sample 13 (AN12, Sample 1) Sample 14 (AN13, Sample 1) Sample 15 (AN14, Sample 1) Sample 16 (AN15, Sample 1)  2012-2016 Microchip Technology Inc. Buffer Contents at 2nd AD1IF Event Sample 17 (AN0, Sample 2) Sample 18 (AN1, Sample 2) Sample 19 (AN2, Sample 2) Sample 20 (AN3, Sample 2) Sample 21 (AN4, Sample 2) Sample 22 (AN5, Sample 2) Sample 23 (AN6, Sample 2) Sample 24 (AN7, Sample 2) Sample 25 (AN8, Sample 2) Sample 26 (AN9, Sample 2) Sample 27 (AN10, Sample 2) Sample 28 (AN11, Sample 2) Sample 29 (AN12, Sample 2) Sample 30 (AN13, Sample 2) Sample 31 (AN14, Sample 2) Sample 32 (AN15, Sample 2) DS30000575C-page 475 PIC18F97J94 FAMILY 22.8.3 USING DUAL BUFFERS Figure 22-18 and Example 22-6 demonstrate using dual buffers and alternating the buffer fill. Setting the BUFM bit enables dual buffers. In this example, an interrupt is generated after each sample. The BUFM setting does not affect other operational parameters. First, the conversion sequence starts filling the buffer at ADCBUF0. After the first interrupt occurs, the buffer begins to fill at ADCBUF8. The BUFS Status bit is toggled after each interrupt. FIGURE 22-18: CONVERTING A SINGLE CHANNEL, ONCE PER INTERRUPT, USING DUAL, 8-WORD BUFFERS Conversion Trigger TSAMP TSAMP TSAMP A/D CLK TCONVTCONVTCONVTCONV Analog Input AN3 TCONVTCONVTCONVTCONV TCONVTCONVTCONVTCONV AN3 AN3 BCLR IFS0, #AD1IF BCLR IFS0, #AD1IF SAMP BUFS ADC1BUF0 ADC1BUF8 AD1IF BSET AD1CON1, #ASAM DS30000575C-page 476 Instruction Execution  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY EXAMPLE 22-6: CONVERTING A SINGLE CHANNEL, ONCE PER INTERRUPT, DUAL BUFFER MODE A/D Configuration: • • • • • • Select AN3 for S/H+ Input (CH0SA = 00011) Select VR- for S/H- Input (CH0NA = 000) Configure for No Input Scan (CSCNA = 0) Use Only MUX A for Sampling (ALTS = 0) Set AD1IF on Every Sample (SMPI = 00000) Configure Buffer as Dual, 8-Word Segments (BUFM = 1) Operational Sequence: 1. 2. 3. 4. 5. Sample MUX A Input, AN3; Convert and Write to Buffer 0h. Set AD1IF Flag (and generate interrupt, if enabled); Write Access Automatically Switches to Alternate Buffer. Sample MUX A Input, AN3; Convert and Write to Buffer 8h. Set AD1IF Flag (and generate interrupt, if enabled); Write Access Automatically Switches to Alternate Buffer. Repeat (1-4). Results Stored in Buffer (after 2 cycles): Buffer Address ADC1BUF0 ADC1BUF1 ADC1BUF2 ADC1BUF3 ADC1BUF4 ADC1BUF5 ADC1BUF6 ADC1BUF7 ADC1BUF8 ADC1BUF9 ADC1BUFA ADC1BUFB ADC1BUFC ADC1BUFD ADC1BUFE ADC1BUFF 22.8.3.1 Buffer Contents at 1st AD1IF Event Sample 1 (AN3, Sample 1) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) Buffer Contents at 2nd AD1IF Event (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) Sample 2 (AN3, Sample 2) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) Using Alternating MUX A and MUX B Input Selections Figure 22-19 and Example 22-7 demonstrate alternate sampling of the inputs assigned to MUX A and MUX B. Setting the ALTS bit enables alternating input selections. The first sample uses the MUX A inputs specified by the CH0SAx and CH0NAx bits. The next sample uses the MUX B inputs, specified by the CH0SBx and CH0NBx bits. This example also demonstrates use of the dual, 8-word buffers. An interrupt occurs after every 8th sample, resulting in filling eight words into the buffer on each interrupt.  2012-2016 Microchip Technology Inc. DS30000575C-page 477 PIC18F97J94 FAMILY FIGURE 22-19: Conversion Trigger CONVERTING TWO INPUTS USING ALTERNATING INPUT SELECTIONS TSAMP TSAMP TSAMP TSAMP TSAMP A/D CLK TCONVTCONV Analog Input AN1 TCONVTCONV AN15 TCONVTCONV AN15 TCONVTCONV AN1 TCONVTCONV AN15 ASAM SAMP Cleared in Software DONE BUFS ADC1BUF0 ADC1BUF1 ADC1BUF2 ADC1BUF3 ADC1BUF4 ADC1BUF5 ADC1BUF6 ADC1BUF7 ADC1BUF8 ADC1BUF9 ADC1BUFA ADC1BUFB AD1IF Cleared by Software DS30000575C-page 478  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY EXAMPLE 22-7: CONVERTING TWO INPUTS BY ALTERNATING MUX A AND MUX B A/D Configuration: • • • • • • • • Select AN1 for MUX A S/H+ Input (CH0SA = 00001) Select VR- for MUX A S/H- Input (CH0NA = 000) Configure for No Input Scan (CSCNA = 0) Select AN15 for MUX B S/H+ Input (CH0SB = 11111) Select VR- for MUX B S/H- Input (CH0NB = 000) Alternate MUX A and MUX B for Sampling (ALTS = 1) Set AD1IF on Every 8th Sample (SMPI = 00111) Configure Buffer as Two, 8-Word Segments (BUFM = 1) Operational Sequence: 1. 2. 3. 4. 5. 6. 7. 8. 9. Sample MUX A Input AN1; Convert and Write to Buffer 0h. Sample MUX B Input AN15; Convert and Write to Buffer 1h. Sample MUX A Input AN1; Convert and Write to Buffer 2h. Sample MUX B Input AN15; Convert and Write to Buffer 3h. Sample MUX A Input AN1; Convert and Write to Buffer 4h. Sample MUX B Input AN15; Convert and Write to Buffer 5h. Sample MUX A Input AN1; Convert and Write to Buffer 6h. Sample MUX B Input AN15; Convert and Write to Buffer 7h. Set AD1IF Flag (and generate interrupt, if enabled); Write Access Automatically Switches to Alternate Buffer. 10. Repeat (1-9); Resume Writing to Buffer with Buffer 8h (first address of alternate buffer). Results Stored in Buffer (after 2 cycles): Buffer Address ADC1BUF0 ADC1BUF1 ADC1BUF2 ADC1BUF3 ADC1BUF4 ADC1BUF5 ADC1BUF6 ADC1BUF7 ADC1BUF8 ADC1BUF9 ADC1BUFA ADC1BUFB ADC1BUFC ADC1BUFD ADC1BUFE ADC1BUFF Buffer Contents at 1st AD1IF Event Sample 1 (AN1, Sample 1) Sample 2 (AN15, Sample 1) Sample 3 (AN1, Sample 2) Sample 4 (AN15, Sample 2) Sample 5 (AN1, Sample 3) Sample 6 (AN15, Sample 3) Sample 7 (AN1, Sample 4) Sample 8 (AN15, Sample 4) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined)  2012-2016 Microchip Technology Inc. Buffer Contents at 2nd AD1IF Event (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) (undefined) Sample 9 (AN1, Sample 5) Sample 10 (AN15, Sample 5) Sample 11 (AN1, Sample 6) Sample 12 (AN15, Sample 6) Sample 13 (AN1, Sample 7) Sample 14 (AN15, Sample 7) Sample 15 (AN1, Sample 8) Sample 16 (AN15, Sample 8) DS30000575C-page 479 PIC18F97J94 FAMILY 22.9 A/D Sampling Requirements The Analog Input model of the 12-bit A/D Converter is shown in Figure 22-20. The total sampling time for the A/D is a function of the holding capacitor charge time. For the A/D Converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the voltage level on the analog input pin. The source impedance (RS), the interconnect impedance (RIC) and the internal sampling switch (RSS) impedance combine to directly affect the time required to charge CHOLD. The combined impedance of the analog sources must, therefore, be small enough FIGURE 22-20: to fully charge the holding capacitor within the chosen sample time. To minimize the effects of pin leakage currents on the accuracy of the A/D Converter, the maximum recommended source impedance, RS, is 2.5 k. After the analog input channel is selected (changed), this sampling function must be completed prior to starting the conversion. The internal holding capacitor will be in a discharged state prior to each sample operation. At least 1 TAD time period should be allowed between conversions for the sample time. For more details, see Section 30.0 “Electrical Specifications”. 12-BIT A/D CONVERTER ANALOG INPUT MODEL RIC  250 Rs VA ANx Sampling Switch RSS CPIN RSS  3 k CHOLD = 4.4 pF ILEAKAGE 500 nA VSS Legend: CPIN = Input Capacitance = Threshold Voltage VT ILEAKAGE = Leakage Current at the Pin due to Various Junctions RIC = Interconnect Resistance RSS = Sampling Switch Resistance CHOLD = Sample/Hold Capacitance (from DAC) Note: CPIN value depends on device package and is not tested. The effect of the CPIN is negligible if Rs  5 k. 22.10 Transfer Functions For the 12-bit transfer function: The transfer functions of the A/D Converter, in 12-bit and 10-bit resolution, are shown in Figure 22-21 and Figure 22-22, respectively. In both cases, the difference of the input voltages, (VINH - VINL), is compared to the reference, ((VR+) - (VR-)). • The first code transition occurs when the input voltage is ((VR+) - (VR-))/4096 or 1.0 LSb. • The '0000 0000 0001' code is centered at VR+ (1.5 * ((VR+) - (VR-)) / 4096). • The '0010 0000 0000' code is centered at VREFL + (2048.5 * ((VR+) - (VR-)) /4096). • An input voltage less than VR- + (((VR-) - (VR-)) / 4096) converts as '0000 0000 0000'. • An input voltage greater than (VR-) + (4096 ((VR+) - (VR-))/4096) converts as '1111 1111 1111'. DS30000575C-page 480  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 22-21: 12-BIT A/D TRANSFER FUNCTION Output Code (Binary (Decimal)) 1111 1111 1111 (4095) 1111 1111 1110 (4094) 0010 0000 0011 (2051) 0010 0000 0010 (2050) 0010 0000 0001 (2049) 0010 0000 0000 (2048) 0001 1111 1111 (2047) 0001 1111 1110 (2046) 0001 1111 1101 (2045) 0000 0000 0001 (1) (VINH – VINL) VR+ 4096 4095 * (VR + – VR-) VR- + 4096 VR- + 2048 * (VR+ – VR-) 4096 VR- + Voltage Level VR+ – VR- 0 VR- 0000 0000 0000 (0) For the 10-bit transfer function (when 10-bit resolution is available): • The first code transition occurs when the input voltage is ((VR+) - (VR-))/1024 or 1.0 LSb. • The '00 0000 0001' code is centered at VR- + (1.5 * (((VR+) - (VR-)) / 1024). • The '10 0000 0000' code is centered at VREFL + (512.5 * (((VR+) - (VR-)) /1024). • An input voltage less than VR- + (((VR-) - (VR-)) / 1024) converts as '00 0000 0000'. • An input voltage greater than (VR-) + ((1023 (VR+)) - (VR-))/1024) converts as '11 1111 1111'.  2012-2016 Microchip Technology Inc. DS30000575C-page 481 PIC18F97J94 FAMILY FIGURE 22-22: 10-BIT A/D TRANSFER FUNCTION Output Code (Binary (Decimal)) 11 1111 1111 (1023) 11 1111 1110 (1022) 10 0000 0011 (515) 10 0000 0010 (514) 10 0000 0001 (513) 10 0000 0000 (512) 01 1111 1111 (511) 01 1111 1110 (510) 01 1111 1101 (509) 00 0000 0001 (1) (VINH – VINL) VR+ 1024 1023 * (VR+ – VR-) VR- + 1024 VR- + 512 * (VR+ – VR-) 1024 VR- + Voltage Level VR+ – VR- 0 VR- 00 0000 0000 (0) 22.11 Operation During Sleep and Idle Modes 22.11.2 Sleep and Idle modes are useful for minimizing conversion noise because the digital activity of the CPU, buses and other peripherals is minimized. The A/D module can operate during Sleep mode if the A/D clock source is set to the internal A/D RC oscillator (ADRC = 1). This eliminates digital switching noise from the conversion. When the conversion is completed, the DONE bit will be set and the result is loaded into the A/D Result Buffer n, ADCBUFn. 22.11.1 CPU SLEEP MODE WITHOUT RC A/ D CLOCK When the device enters Sleep mode, all clock sources to the module are shut down and stay at logic '0'. If Sleep occurs in the middle of a conversion, the conversion is aborted unless the A/D is clocked from its internal RC clock generator. The converter will not resume a partially completed conversion on exiting from Sleep mode. Register contents are not affected by the device entering or leaving Sleep mode. DS30000575C-page 482 CPU SLEEP MODE WITH RC A/D CLOCK If the A/D interrupt is enabled (ADIE = 1), the device will wake-up from Sleep when the A/D interrupt occurs. Program execution will resume at the A/D Interrupt Service Routine (ISR). After the ISR completes execution will continue from the instruction after the SLEEP instruction that placed the device in Sleep mode. If the A/D interrupt is not enabled, the A/D module will then be turned off, although the ADON bit will remain set.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY To minimize the effects of digital noise on the A/D module operation, the user should select a conversion trigger source that ensures the A/D conversion will take place in Sleep mode. The automatic conversion trigger option can be used for sampling and conversion in Sleep (SSRC = 0111). To use the automatic conversion option, the ADON bit should be set in the instruction prior to the SLEEP instruction. Note: For the A/D module to operate in Sleep, the A/D clock source must be set to RC (ADRC = 1). 22.11.3 A/D OPERATION DURING CPU IDLE MODE The module will continue normal operation when the device enters Idle mode. If the A/D interrupt is enabled (ADIE = 1), the device will wake-up from Idle mode when the A/D interrupt occurs. If the respective global interrupt enable bit(s) are also set, program execution will resume at the A/D Interrupt Service Routine (ISR). After the ISR completes, execution will continue from the instruction after the SLEEP instruction that placed the device in Idle mode. 22.11.4 PERIPHERAL MODULE DISABLE (PMD) REGISTER The Peripheral Module Disable (PMD) registers provide a method to disable the A/D module by stopping all clock sources supplied to that module. When a peripheral is disabled via the appropriate PMDx control bit, the peripheral is in a minimum power consumption state. The control and STATUS registers associated with the peripheral will also be disabled, so writes to those registers will have no effect and read values will be invalid. The A/D module is enabled only when the ADCMD bit in the PMD3 register is cleared. 2. 3. is complete. These timing specifications are provided in the “Electrical Characteristics” section of the device data sheets. Often, the source impedance of the analog signal is high (greater than 2.5 k), so the current drawn from the source by leakage, and to charge the sample capacitor, can affect accuracy. If the input signal does not change too quickly, try putting a 0.1 uF capacitor on the analog input. This capacitor will charge to the analog voltage being sampled and supply the instantaneous current needed to charge the internal holding capacitor. Put the device into Sleep mode before the start of the A/D conversion. The RC clock source selection is required for conversions in Sleep mode. This technique increases accuracy, because digital noise from the CPU and other peripherals is minimized. Question 2: Do you know of a good reference on A/ D Converters? Answer: A good reference for understanding A/D conversions is the “Analog-Digital Conversion Handbook third edition, published by Prentice Hall (ISBN 0-13-03-2848-0). Question 3: My combination of channels/samples and samples/interrupt is greater than the size of the buffer. What will happen to the buffer? Answer: This configuration is not recommended. The buffer will contain unknown results. 22.13 Related Application Notes Question 1: How can I optimize the system performance of the A/D Converter? This section lists application notes that are related to this section of the data sheet. These application notes may not be written specifically for the PIC18F device family, but the concepts are pertinent and could be used with modification and possible limitations. The current application notes related to the 12-Bit A/D Converter with Threshold Detect module are: Answer: There are three main things to consider in optimizing A/D performance: AN546, Using the Analog-to-Digital (A/D) Converter (DS00546) 1. AN557, Four-Channel Digital Voltmeter with Display and Keyboard (DS00557) 22.12 Design Tips Make sure you are meeting all of the timing specifications. If you are turning the module off and on, there is a minimum delay you must wait before taking a sample. If you are changing input channels, there is a minimum delay you must wait for this as well, and finally, there is TAD, which is the time selected for each bit conversion. This is selected in AD1CON3 and should be within a certain range, as specified in Section 30.0 “Electrical Specifications”. If TAD is too short, the result may not be fully converted before the con- version is terminated, and if TAD is made too long, the voltage on the sampling capacitor can decay before the conversion  2012-2016 Microchip Technology Inc. AN693, Understanding A/D Converter Performance Specifications (DS00693) Note: Visit the Microchip web site (www.microchip.com) for additional application notes and code examples for the PIC18F family of devices. DS30000575C-page 483 PIC18F97J94 FAMILY 23.0 COMPARATOR MODULE 23.1 The analog comparator module contains three comparators that can be independently configured in a variety of ways. The inputs can be selected from the analog inputs and two internal voltage references. The digital outputs are available at the pin level, via PPS-Lite, and can also be read through the control register. Multiple output and interrupt event generations are also available. A generic single comparator from the module is shown in Figure 23-1. Registers The CMxCON registers (CM1CON, CM2CON and CM3CON) select the input and output configuration for each comparator, as well as the settings for interrupt generation (see Register 23-1). The CMSTAT register (Register 23-2) provides the output results of the comparators. The bits in this register are read-only. Key features of the module includes: • • • • • Independent comparator control Programmable input configuration Output to both pin and register levels Programmable output polarity Independent interrupt generation for each comparator with configurable interrupt-on-change FIGURE 23-1: COMPARATOR SIMPLIFIED BLOCK DIAGRAM CxOUT (CMSTAT) CCH CxINB 0 CxINC 1 C2INB/C2IND(1) 2 VBG 3 Interrupt Logic CMPxIF EVPOL CREF COE VIN- Note 1: CxINA 0 CVREF 1 VIN+ Cx Polarity Logic CON CPOL CxOUT Comparator 1 and Comparator 3 use C2INB as an input to the inverted terminal. Comparator 2 uses C2IND as an input to the inverted terminal. DS30000575C-page 484  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 23-1: CMxCON: COMPARATOR CONTROL x REGISTER R/W-0 R/W-0 R/W-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 CON COE CPOL EVPOL1 EVPOL0 CREF CCH1 CCH0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 CON: Comparator Enable bit 1 = Comparator is enabled 0 = Comparator is disabled bit 6 COE: Comparator Output Enable bit 1 = Comparator output is present on the CxOUT pin 0 = Comparator output is internal only bit 5 CPOL: Comparator Output Polarity Select bit 1 = Comparator output is inverted 0 = Comparator output is not inverted bit 4-3 EVPOL: Interrupt Polarity Select bits 11 = Interrupt generation on any change of the output(1) 10 = Interrupt generation only on high-to-low transition of the output 01 = Interrupt generation only on low-to-high transition of the output 00 = Interrupt generation is disabled bit 2 CREF: Comparator Reference Select bit (non-inverting input) 1 = Non-inverting input connects to internal CVREF voltage 0 = Non-inverting input connects to CxINA pin bit 1-0 CCH: Comparator Channel Select bits 11 = Inverting input of comparator connects to VBG 10 = Inverting input of comparator connects to C2INB pin 01 = Inverting input of comparator connects to CxINC pin 00 = Inverting input of comparator connects to CxINx pin(2) Note 1: 2: x = Bit is unknown The CMPxIF is automatically set any time this mode is selected and must be cleared by the application after the initial configuration. Comparator 1 and Comparator 3 use C2INB as an input to the inverting terminal. Comparator 2 uses C2IND as an input to the inverting terminal.  2012-2016 Microchip Technology Inc. DS30000575C-page 485 PIC18F97J94 FAMILY REGISTER 23-2: CMSTAT: COMPARATOR STATUS REGISTER U-0 U-0 U-0 U-0 U-0 R-x R-x R-x — — — — — C3OUT C2OUT C1OUT bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-3 Unimplemented: Read as ‘0’ bit 2-0 C3OUT:C1OUT: Comparator x Status bits If CPOL (CMxCON)= 0 (non-inverted polarity): 1 = Comparator x’s VIN+ > VIN0 = Comparator x’s VIN+ < VINCPOL = 1 (inverted polarity): 1 = Comparator x’s VIN+ < VIN0 = Comparator x’s VIN+ > VIN- 23.2 Comparator Operation A single comparator is shown in Figure 23-2, along with the relationship between the analog input levels and the digital output. When the analog input at VIN+ is less than the analog input, VIN-, the output of the comparator is a digital low level. When the analog input at VIN+ is greater than the analog input, VIN-, the output of the comparator is a digital high level. The shaded areas of the output of the comparator in Figure 23-2 represent the uncertainty due to input offsets and response time. FIGURE 23-2: VIN- SINGLE COMPARATOR – Output VIN+ + x = Bit is unknown comparator input change. Otherwise, the maximum delay of the comparators should be used (see Section 30.0 “Electrical Specifications”). 23.4 Analog Input Connection Considerations A simplified circuit for an analog input is shown in Figure 23-3. Since the analog pins are connected to a digital output, they have reverse biased diodes to VDD and VSS. The analog input, therefore, must be between VSS and VDD. If the input voltage deviates from this range by more than 0.6V in either direction, one of the diodes is forward biased and a latch-up condition may occur. A maximum source impedance of 10 k is recommended for the analog sources. Any external component connected to an analog input pin, such as a capacitor or a Zener diode, should have very little leakage current. VINVIN+ Output 23.3 Comparator Response Time Response time is the minimum time, after selecting a new reference voltage or input source, before the comparator output has a valid level. The response time of the comparator differs from the settling time of the voltage reference. Therefore, both of these times must be considered when determining the total response to a DS30000575C-page 486  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY FIGURE 23-3: COMPARATOR ANALOG INPUT MODEL VDD RIC RS CxINA Compare CON = 1, CREF = 0, CCH = 00 CxOUT Pin Comparator CxINC > CxINA Compare CON = 1, CREF = 0, CCH = 01 COE CxINB CxINA COE VINVIN+ Cx CxOUT Pin Comparator C2IND/C2INB > CxINA Compare CON = 1, CREF = 0, CCH = 10 CxINC VIN- CxINA VIN+ Cx CxOUT Pin Comparator VBG > CxINA Compare CON = 1, CREF = 0, CCH = 11 COE C2IND/ C2INB CxINA COE VINVIN+ Cx CxOUT Pin Comparator CxINB > CVREF Compare CON = 1, CREF = 1, CCH = 00 VBG VIN- CxINA VIN+ Cx Comparator CxINC > CVREF Compare CON = 1, CREF = 1, CCH = 01 COE CxINB CVREF COE VINVIN+ Cx CxOUT Pin CxINC VIN- CVREF VIN+ Cx COE CVREF Note 1: COE VINVIN+ Cx CxOUT Pin Comparator VBG > CVREF Compare CON = 1, CREF = 1, CCH = 11 Comparator C2IND/C2INB > CVREF Compare CON = 1, CREF = 1, CCH = 10 C2IND/ C2INB CxOUT Pin CxOUT Pin VBG VIN- CVREF VIN+ Cx CxOUT Pin VBG is the Internal Reference Voltage (see Table 30-14).  2012-2016 Microchip Technology Inc. DS30000575C-page 489 PIC18F97J94 FAMILY 23.6 Comparator Interrupts The comparator interrupt flag is set whenever any of the following occurs: • Low-to-high transition of the comparator output • High-to-low transition of the comparator output • Any change in the comparator output The comparator interrupt selection is done by the EVPOL bits in the CMxCON register (CMxCON). In order to provide maximum flexibility, the output of the comparator may be inverted using the CPOL bit in the CMxCON register (CMxCON). This is functionally identical to reversing the inverting and non-inverting inputs of the comparator for a particular mode. An interrupt is generated on the low-to-high or high-tolow transition of the comparator output. This mode of interrupt generation is dependent on EVPOL in the CMxCON register. When EVPOL = 01 or 10, the interrupt is generated on a low-to-high or high-tolow transition of the comparator output. Once the interrupt is generated, it is required to clear the interrupt flag by software. TABLE 23-2: When EVPOL = 11, the comparator interrupt flag is set whenever there is a change in the output value of either comparator. Software will need to maintain information about the status of the output bits, as read from CMSTAT, to determine the actual change that occurred. The CMPxIF (PIR6) bits are the Comparator Interrupt Flags. The CMPxIF bits must be reset by clearing them. Since it is also possible to write a ‘1’ to this register, a simulated interrupt may be initiated. Table 23-2 shows the interrupt generation with respect to comparator input voltages and EVPOL bit settings. Both the CMPxIE bits (PIE6) and the PEIE bit (INTCON) must be set to enable the interrupt. In addition, the GIE bit (INTCON) must also be set. If any of these bits are clear, the interrupt is not enabled, though the CMPxIF bits will still be set if an interrupt condition occurs. A simplified diagram of the interrupt section is shown in Figure 23-3. Note: CMPxIF will not EVPOL = 00. be set when COMPARATOR INTERRUPT GENERATION CPOL EVPOL 00 01 0 10 11 00 01 1 10 11 DS30000575C-page 490 Comparator Input Change CxOUT Transition Interrupt Generated VIN+ > VIN- Low-to-High No VIN+ < VIN- High-to-Low No VIN+ > VIN- Low-to-High Yes VIN+ < VIN- High-to-Low No VIN+ > VIN- Low-to-High No VIN+ < VIN- High-to-Low Yes VIN+ > VIN- Low-to-High Yes VIN+ < VIN- High-to-Low Yes VIN+ > VIN- High-to-Low No VIN+ < VIN- Low-to-High No VIN+ > VIN- High-to-Low No VIN+ < VIN- Low-to-High Yes VIN+ > VIN- High-to-Low Yes VIN+ < VIN- Low-to-High No VIN+ > VIN- High-to-Low Yes VIN+ < VIN- Low-to-High Yes  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 23.7 Comparator Operation During Sleep When a comparator is active and the device is placed in Sleep mode, the comparator remains active and the interrupt is functional, if enabled. This interrupt will wake-up the device from Sleep mode when enabled. Each operational comparator will consume additional current. 23.8 Effects of a Reset A device Reset forces the CMxCON registers to their Reset state. This forces both comparators and the voltage reference to the OFF state. To minimize power consumption while in Sleep mode, turn off the comparators (CON = 0) before entering Sleep. If the device wakes up from Sleep, the contents of the CMxCON register are not affected.  2012-2016 Microchip Technology Inc. DS30000575C-page 491 PIC18F97J94 FAMILY 24.0 COMPARATOR VOLTAGE REFERENCE MODULE EQUATION 24-1: If CVRSS = 1: The comparator voltage reference is a 32-tap resistor ladder network that provides a selectable reference voltage. Although its primary purpose is to provide a reference for the analog comparators, it may also be used independently of them. A block diagram of the module is shown in Figure 24-1. The resistor ladder is segmented to provide a range of CVREF values and has a power-down function to conserve power when the reference is not being used. The module’s supply reference can be provided from either device VDD/VSS or an external voltage reference. 24.1 Configuring the Comparator Voltage Reference The comparator voltage reference module is controlled through the CVRCONH register (Register 24-1). The comparator voltage reference provides a range of output voltage with 32 levels. CVR CVREF =( VREF- + ) • (VREF+ – VREF-) 32 If CVRSS = 0: CVR CVREF =( AVSS + ) • (AVDD – AVSS) 32 The comparator voltage reference supply can come from either VDD and VSS, or the external VREF+ and VREF- that are multiplexed with RA3 and RA2. The voltage source is selected by the CVRPSS bits (CVRCONL). The settling time of the comparator voltage reference must be considered when changing the CVREF output (see Table 30-13 in Section 30.0 “Electrical Specifications”). The CVR selection bits (CVRCONH) offer a range of output voltages. Equation 24-1 shows how the comparator voltage reference is computed. REGISTER 24-1: CVRCONH: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER HIGH U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — CVR4 CVR3 CVR2 CVR1 CVR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-5 Unimplemented: Read as ‘0’ bit 4-0 CVR: Comparator VREF Value Selection 0  CVR  31 bits CVREF = VNEGSRC + (CVR/32) • (VPOSSRC – VNEGSRC) DS30000575C-page 492  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 24-2: CVRCONL: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 CVREN CVROE CVRPSS1 CVRPSS0 — — — CVRNSS bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 CVREN: Comparator Voltage Reference Enable bit 1 = CVREF circuit is powered on 0 = CVREF circuit is powered down bit 6 CVROE: Comparator VREF Output Enable bit 1 = CVREF voltage level is output on CVREF pin 0 = CVREF voltage level is disconnected from CVREF pin bit 5-4 CVRPSS: Comparator VREF Positive Source (VPOSSRC) Selection bits 11 = Reserved, do not use. Positive source is floating 10 = VBG (Band gap) 01 = VREF+ 00 = AVDD bit 3-1 Unimplemented: Read as ‘0’ bit 0 CVRNSS: Comparator VREF Negative Source (VNEGSRC) Selection bit 01 = VREF00 = AVSS FIGURE 24-1: COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM VREF+ AVDD CVRSS = 1 8R CVRSS = 0 CVR R CVREN R R 32 Steps R 32-to-1 MUX R CVREF R R VREF- CVRSS = 1 CVRSS = 0  2012-2016 Microchip Technology Inc. DS30000575C-page 493 PIC18F97J94 FAMILY 24.2 Voltage Reference Accuracy/Error The full range of voltage reference cannot be realized due to the construction of the module. The transistors on the top and bottom of the resistor ladder network (Figure 24-1) keep CVREF from approaching the reference source rails. The voltage reference is derived from the reference source; therefore, the CVREF output changes with fluctuations in that source. The tested absolute accuracy of the voltage reference can be found in Section 30.0 “Electrical Specifications”. 24.3 Operation During Sleep When the device wakes up from Sleep through an interrupt or a Watchdog Timer time-out, the contents of the CVRCON register are not affected. To minimize current consumption in Sleep mode, the voltage reference should be disabled. FIGURE 24-2: 24.4 Effects of a Reset A device Reset disables the voltage reference by clearing bit, CVREN (CVRCONL). This Reset also disconnects the reference from the RF5 pin by clearing bit, CVROE (CVRCONL). 24.5 Connection Considerations The voltage reference module operates independently of the comparator module. The output of the reference generator may be connected to the RA0 pin if the CVROE bit is set. Enabling the voltage reference output onto RA0, when it is configured as a digital input, will increase current consumption. Connecting RA0 as a digital output with CVRSS enabled will also increase current consumption. The RA0 pin can be used as a simple D/A output with limited drive capability. Due to the limited current drive capability, a buffer must be used on the voltage reference output for external connections to VREF. Figure 24-2 shows an example buffering technique. COMPARATOR VOLTAGE REFERENCE OUTPUT BUFFER EXAMPLE PIC18F97J94 CVREF Module R(1) Voltage Reference Output Impedance Note 1: RF5 + – CVREF Output R is dependent upon the Comparator Voltage Reference bits, CVRCONH, CVRCONL and CVRCONL. DS30000575C-page 494  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 25.0 HIGH/LOW-VOLTAGE DETECT (HLVD) The PIC18FXXJ94 of devices has a High/Low-Voltage Detect module (HLVD). This is a programmable circuit that sets both a device voltage trip point and the direction of change from that point. If the device experiences an excursion past the trip point in that direction, an interrupt flag is set. If the interrupt is enabled, the program execution branches to the interrupt vector address and the software responds to the interrupt. The High/Low-Voltage Detect Control register (Register 25-1) completely controls the operation of the HLVD module. This allows the circuitry to be “turned off” by the user under software control, which minimizes the current consumption for the device. The module’s block diagram is shown in Figure 25-1. REGISTER 25-1: HLVDCON: HIGH/LOW-VOLTAGE DETECT CONTROL REGISTER R/W-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 VDIRMAG BGVST IRVST HLVDEN HLVDL3(1) HLVDL2(1) HLVDL1(1) HLVDL0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 VDIRMAG: Voltage Direction Magnitude Select bit 1 = Event occurs when voltage equals or exceeds trip point (HLVDL) 0 = Event occurs when voltage equals or falls below trip point (HLVDL) bit 6 BGVST: Band Gap Reference Voltages Stable Status Flag bit 1 = Internal band gap voltage references are stable 0 = Internal band gap voltage references are not stable bit 5 IRVST: Internal Reference Voltage Stable Flag bit 1 = Indicates that the voltage detect logic will generate the interrupt flag at the specified voltage range 0 = Indicates that the voltage detect logic will not generate the interrupt flag at the specified voltage range and the HLVD interrupt should not be enabled bit 4 HLVDEN: High/Low-Voltage Detect Power Enable bit 1 = HLVD is enabled 0 = HLVD is disabled bit 3-0 HLVDL: Voltage Detection Limit bits(1) 1111 = External analog input is used (input comes from the HLVDIN pin) 1110 = Maximum setting . . . 0100 = Minimum setting Note 1: For the electrical specifications, see Parameter D420.  2012-2016 Microchip Technology Inc. DS30000575C-page 495 PIC18F97J94 FAMILY The module is enabled by setting the HLVDEN bit (HLVDCON). Each time the HLVD module is enabled, the circuitry requires some time to stabilize. The IRVST bit (HLVDCON) is a read-only bit used to indicate when the circuit is stable. The module can only generate an interrupt after the circuit is stable and IRVST is set. trip point voltage. The “trip point” voltage is the voltage level at which the device detects a high or low-voltage event, depending on the configuration of the module. When the supply voltage is equal to the trip point, the voltage tapped off of the resistor array is equal to the internal reference voltage generated by the voltage reference module. The comparator then generates an interrupt signal by setting the HLVDIF bit. The VDIRMAG bit (HLVDCON) determines the overall operation of the module. When VDIRMAG is cleared, the module monitors for drops in VDD below a predetermined set point. When the bit is set, the module monitors for rises in VDD above the set point. 25.1 The trip point voltage is software programmable to any of 16 values. The trip point is selected by programming the HLVDL bits (HLVDCON). The HLVD module has an additional feature that allows the user to supply the trip voltage to the module from an external source. This mode is enabled when bits, HLVDL, are set to ‘1111’. In this state, the comparator input is multiplexed from the external input pin, HLVDIN. This gives users the flexibility of configuring the High/Low-Voltage Detect interrupt to occur at any voltage in the valid operating range. Operation When the HLVD module is enabled, a comparator uses an internally generated reference voltage as the set point. The set point is compared with the trip point, where each node in the resistor divider represents a FIGURE 25-1: VDD HLVD MODULE BLOCK DIAGRAM (WITH EXTERNAL INPUT) Externally Generated Trip Point VDD HLVDL HLVDCON Register HLVDEN VDIRMAG Set HLVDIF 16-to-1 MUX HLVDIN HLVDEN BOREN DS30000575C-page 496 Internal Voltage Reference 1.2V Typical  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 25.2 HLVD Setup To set up the HLVD module: 1. 2. 3. 4. 5. Select the desired HLVD trip point by writing the value to the HLVDL bits. Set the VDIRMAG bit to detect high voltage (VDIRMAG = 1) or low voltage (VDIRMAG = 0). Enable the HLVD module by setting the HLVDEN bit. Clear the HLVD interrupt flag (PIR2), which may have been set from a previous interrupt. If interrupts are desired, enable the HLVD interrupt by setting the HLVDIE and GIE bits (PIE2 and INTCON, respectively). An interrupt will not be generated until the IRVST bit is set. Note: Before changing any module settings (VDIRMAG, HLVDL), first disable the module (HLVDEN = 0), make the changes and re-enable the module. This prevents the generation of false HLVD events. 25.3 Current Consumption When the module is enabled, the HLVD comparator and voltage divider are enabled and consume static current. Depending on the application, the HLVD module does not need to operate constantly. To reduce current requirements, the HLVD circuitry may only need to be enabled for short periods where the voltage is checked. After such a check, the module could be disabled. 25.4 HLVD Start-up Time The internal reference voltage of the HLVD module, specified in electrical specification, Parameter 37 (Section 30.0 “Electrical Specifications”), may be used by other internal circuitry, such as the programmable Brown-out Reset. If the HLVD or other circuits using the voltage reference are disabled to lower the device’s current consumption, the reference voltage circuit will require time to become stable before a low or high-voltage condition can be reliably detected. This start-up time, TIRVST, is an interval that is independent of device clock speed. It is specified in electrical specification, Parameter 37 (Table 30-26). The HLVD interrupt flag is not enabled until TIRVST has expired and a stable reference voltage is reached. For this reason, brief excursions beyond the set point may not be detected during this interval (see Figure 25-2 or Figure 25-3).  2012-2016 Microchip Technology Inc. DS30000575C-page 497 PIC18F97J94 FAMILY FIGURE 25-2: LOW-VOLTAGE DETECT OPERATION (VDIRMAG = 0) CASE 1: HLVDIF will Not be Set VDD VHLVD HLVDIF Enable HLVD TIRVST IRVST HLVDIF Cleared in Software Internal Reference is Stable CASE 2: VDD VHLVD HLVDIF Enable HLVD TIRVST IRVST HLVDIF Cleared in Software Internal Reference is Stable HLVDIF Cleared in Software, HLVDIF Remains Set Since HLVD Condition still Exists FIGURE 25-3: HIGH-VOLTAGE DETECT OPERATION (VDIRMAG = 1) CASE 1: HLVDIF will not be Set VHLVD VDD HLVDIF Enable HLVD TIRVST IRVST HLVDIF Cleared in Software Internal Reference is Stable CASE 2: VHLVD VDD HLVDIF Enable HLVD TIRVST IRVST Internal Reference is Stable DS30000575C-page 498 HLVDIF Cleared in Software HLVDIF Cleared in Software, HLVDIF Remains Set since HLVD Condition still Exists  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 25.5 Applications 25.6 In many applications, it is desirable to detect a drop below, or rise above, a particular voltage threshold. For example, the HLVD module could be periodically enabled to detect Universal Serial Bus (USB) attach or detach. This assumes the device is powered by a lower voltage source than the USB when detached. An attach would indicate a high-voltage detect from, for example, 3.3V to 5V (the voltage on USB) and vice versa for a detach. This feature could save a design a few extra components and an attach signal (input pin). For general battery applications, Figure 25-4 shows a possible voltage curve. Over time, the device voltage decreases. When the device voltage reaches voltage, VA, the HLVD logic generates an interrupt at time, TA. The interrupt could cause the execution of an ISR, which would allow the application to perform “housekeeping tasks” and a controlled shutdown, before the device voltage exits the valid operating range at TB. This would give the application a time window, represented by the difference between TA and TB, to safely exit. FIGURE 25-4: Operation During Sleep When enabled, the HLVD circuitry continues to operate during Sleep. If the device voltage crosses the trip point, the HLVDIF bit will be set and the device will wake-up from Sleep. Device execution will continue from the interrupt vector address if interrupts have been globally enabled. 25.7 Effects of a Reset A device Reset forces all registers to their Reset state. This forces the HLVD module to be turned off. TYPICAL LOW-VOLTAGE DETECT APPLICATION Voltage VA VB TA Time TB Legend: VA = HLVD trip point VB = Minimum valid device operating voltage  2012-2016 Microchip Technology Inc. DS30000575C-page 499 PIC18F97J94 FAMILY 26.0 CHARGE TIME MEASUREMENT UNIT (CTMU) • • • • • Control of edge sequence Control of response to edges Time measurement resolution of 1 nanosecond High-precision time measurement Time delay of external or internal signal asynchronous to system clock • Accurate current source suitable for capacitive measurement The Charge Time Measurement Unit (CTMU) is a flexible analog module that provides accurate differential time measurement between pulse sources, as well as asynchronous pulse generation. By working with other on-chip analog modules, the CTMU can precisely measure time, capacitance and relative changes in capacitance or generate output pulses with a specific time delay. The CTMU is ideal for interfacing with capacitive-based sensors. The CTMU works in conjunction with the A/D Converter to provide up to 24 channels for time or charge measurement, depending on the specific device and the number of A/D channels available. When configured for time delay, the CTMU is connected to one of the analog comparators. The level-sensitive input edge sources can be selected from four sources: two external inputs or the CCP1/CCP2 Special Event Triggers. The module includes these key features: • Up to 24 channels available for capacitive or time measurement input • Low-cost temperature measurement using on-chip diode channel • On-chip precision current source • Sixteen-edge input trigger sources • Polarity control for each edge source • Provides a trigger for the A/D Converter FIGURE 26-1: The CTMU special event can trigger the Analog-to-Digital Converter module. Figure 26-1 provides a block diagram of the CTMU. CTMU BLOCK DIAGRAM CTMUCONH:CTMUCONL EDGEN EDGSEQEN EDG1SEL EDG1POL EDG2SEL EDG2POL CTED1 CTED2 CTMUCON1 ITRIM IRNG EDG1STAT EDG2STAT Edge Control Logic Current Source Current Control CCP2 TGEN IDISSEN CTTRIG CTMU Control Logic Pulse Generator CCP1 A/D Converter A/D Trigger CTPLS Comparator 2 Input Comparator 2 Output DS30000575C-page 500  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 26.1 CTMU Registers The CTMUCON1 and CTMUCON3 registers (Register 26-1 and Register 26-3) contain control bits for configuring the CTMU module edge source selection, edge source polarity selection, edge sequencing, A/D trigger, analog circuit capacitor discharge and enables. The CTMUCON2 register (Register 26-2) has bits for selecting the current source range and current source trim. The control registers for the CTMU are: • • • • CTMUCON1 CTMUCON2 CTMUCON3 CTMUCON4 REGISTER 26-1: CTMUCON1: CTMU CONTROL REGISTER 1 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CTMUEN — CTMUSIDL TGEN EDGEN EDGSEQEN IDISSEN CTTRIG bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 CTMUEN: CTMU Enable bit 1 = Module is enabled 0 = Module is disabled bit 6 Unimplemented: Read as ‘0’ bit 5 CTMUSIDL: Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 4 TGEN: Time Generation Enable bit 1 = Enables edge delay generation 0 = Disables edge delay generation bit 3 EDGEN: Edge Enable bit 1 = Edges are not blocked 0 = Edges are blocked bit 2 ESGSEQEN: Edge Sequence Enable bit 1 = Edge 1 event must occur before Edge 2 event can occur 0 = No edge sequence is needed bit 1 IDISSEN: Analog Current Source Control bit 1 = Analog current source output is grounded 0 = Analog current source output is not grounded bit 0 CTTRIG: CTMU Special Event Trigger bit 1 = CTMU Special Event Trigger is enabled 0 = CTMU Special Event Trigger is disabled  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 501 PIC18F97J94 FAMILY REGISTER 26-2: CTMUCON2: CTMU CURRENT CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ITRIM5 ITRIM4 ITRIM3 ITRIM2 ITRIM1 ITRIM0 IRNG1 IRNG0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-2 ITRIM: Current Source Trim bits 011111 = Maximum positive change (+62% typ.) from nominal current 011110 . . . 000001 = Minimum positive change (+2% typ.) from nominal current 000000 = Nominal current output specified by IRNG 111111 = Minimum negative change (-2% typ.) from nominal current . . . 100010 100001 = Maximum negative change (-62% typ.) from nominal current bit 1-0 IRNG: Current Source Range Select bits 11 = 100 x Base Current 10 = 10 x Base Current 01 = Base Current Level (0.55 A nominal) 00 = 1000 x Base Current DS30000575C-page 502  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY REGISTER 26-3: R/W-0 EDG2EN CTMUCON3: CTMU CURRENT CONTROL REGISTER 3 R/W-0 EDG2POL R/W-0 EDG2SEL3 R/W-0 EDG2SEL2 R/W-0 EDG2SEL1 R/W-0 U-0 U-0 EDG2SEL0 — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 EDG2EN: Edge 2 Edge-Sensitive Select bit 1 = Input is edge-sensitive 0 = Input is level-sensitive bit 6 EDG2POL: Edge 2 Polarity Select bit 1 = Edge 2 is programmed for a positive edge response 0 = Edge 2 is programmed for a negative edge response bit 5-2 EDG2SEL: Edge 2 Source Select bits 1111 = CMP3 selected 1110 = CMP2 selected 1101 = CMP1 selected 1100 = Reserved 1011 = CCP3 trigger selected 1010 = CCP2 trigger selected 1001 = CCP1 trigger selected 1000 = CTED13 selected 0111 = CTED12 selected 0110 = CTED11 selected 0101 = CTED10 selected 0100 = CTED9 selected 0011 = CTED1 selected 0010 = CTED2 selected 0001 = CCP1 interrupt selected 0000 = TMR1 interrupt selected bit 1-0 Unimplemented: Read as ‘0’  2012-2016 Microchip Technology Inc. x = Bit is unknown DS30000575C-page 503 PIC18F97J94 FAMILY REGISTER 26-4: CTMUCON4: CTMU CURRENT CONTROL REGISTER 4 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 EDG1EN EDG1POL EDG1SEL3 EDG1SEL2 EDG1SEL1 EDG1SEL0 EDG2STAT EDG1STAT bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 EDG1EN: Edge 1 Edge-Sensitive Select bit 1 = Input is edge-sensitive 0 = Input is level-sensitive bit 6 EDG1POL: Edge 1 Polarity Select bit 1 = Edge 1 is programmed for a positive edge response 0 = Edge 1 is programmed for a negative edge response bit 5-2 EDG1SEL: Edge 1 Source Select bits 1111 = CMP3 selected 1110 = CMP2 selected 1101 = CMP1 selected 1100 = CCP3 trigger selected 1011 = CCP2 trigger selected 1010 = CCP1 trigger selected 1001 = CTED8 selected 1000 = CTED7 selected 0111 = CTED6 selected 0110 = CTED5 selected 0101 = CTED4 selected 0100 = CTED3 selected 0011 = CTED1 selected 0010 = CTED2 selected 0001 = CCP1 interrupt selected 0000 = TMR1 interrupt selected bit 1-0 EDG2STAT: Edge 2 Status bit Indicates the status of Edge 2 and can be written to control edge source. 1 = Edge2 has occurred 0 = Edge2 has not occurred bit 1-0 EDG1STAT: Edge 1 Status bit 1 = Edge 1 has occurred 0 = Edge 1 has not occurred DS30000575C-page 504  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 26.2 CTMU Operation The CTMU works by using a fixed current source to charge a circuit. The type of circuit depends on the type of measurement being made. In the case of charge measurement, the current is fixed and the amount of time the current is applied to the circuit is fixed. The amount of voltage read by the A/D becomes a measurement of the circuit’s capacitance. In the case of time measurement, the current, as well as the capacitance of the circuit, is fixed. In this case, the voltage read by the A/D is representative of the amount of time elapsed from the time the current source starts and stops charging the circuit. If the CTMU is being used as a time delay, both capacitance and current source are fixed, as well as the voltage supplied to the comparator circuit. The delay of a signal is determined by the amount of time it takes the voltage to charge to the comparator threshold voltage. 26.2.1 THEORY OF OPERATION The operation of the CTMU is based on the equation for charge: I=C• dV dT More simply, the amount of charge measured in coulombs in a circuit is defined as current in amperes (I), multiplied by the amount of time in seconds that the current flows (t). Charge is also defined as the capacitance in farads (C), multiplied by the voltage of the circuit (V). It follows that: I•t=C•V The CTMU module provides a constant, known current source. The A/D Converter is used to measure (V) in the equation, leaving two unknowns: capacitance (C) and time (t). The above equation can be used to calculate capacitance or time, by either the relationship using the known fixed capacitance of the circuit: t = (C • V)/I or by: C = (I • t)/V using a fixed time that the current source is applied to the circuit. 26.2.2 CURRENT SOURCE At the heart of the CTMU is a precision current source, designed to provide a constant reference for measurements. The level of current is user-selectable across three ranges, or a total of two orders of magnitude, with the ability to trim the output in ±2% increments (nominal). The current range is selected by the IRNG bits (CTMUCON1), with a value of ‘01’ representing the lowest range.  2012-2016 Microchip Technology Inc. Current trim is provided by the ITRIM bits (CTMUCON1). These six bits allow trimming of the current source, in steps of approximately 2% per step. Half of the range adjusts the current source positively and the other half reduces the current source. A value of ‘000000’ is the neutral position (no change). A value of ‘100001’ is the maximum negative adjustment (approximately -62%) and ‘011111’ is the maximum positive adjustment (approximately +62%). 26.2.3 EDGE SELECTION AND CONTROL CTMU measurements are controlled by edge events occurring on the module’s two input channels. Each channel, referred to as Edge 1 and Edge 2, can be configured to receive input pulses from one of the edge input pins (CTED1 and CTED2) or CCPx Special Event Triggers (CCP1 and CCP2). The input channels are level-sensitive, responding to the instantaneous level on the channel rather than a transition between levels. The inputs are selected using the EDG1SELx (CTMUCON2) and EDG2SELx (CTMUCON3) bit pairs. In addition to source, each channel can be configured for event polarity using the EDGE2POL (CTMUCON2) and EDGE1POL (CTMUCON3 bits. The input channels can also be filtered for an edge event sequence (Edge 1 occurring before Edge 2) by setting the EDGSEQEN bit (CTMUCON). 26.2.4 EDGE STATUS The CTMUCON3 register also contains two Edge Status bits: EDG2STAT and EDG1STAT (CTMUCON3). Their primary function is to show if an edge response has occurred on the corresponding channel. The CTMU automatically sets a particular bit when an edge response is detected on its channel. The level-sensitive nature of the input channels also means that the Status bits become set immediately if the channel’s configuration is changed and matches the channel’s current state. The module uses the Edge Status bits to control the current source output to external analog modules (such as the A/D Converter). Current is only supplied to external modules when only one (not both) of the Status bits is set. Current is shut off when both bits are either set or cleared. This allows the CTMU to measure current only during the interval between edges. After both Status bits are set, it is necessary to clear them before another measurement is taken. Both bits should be cleared simultaneously, if possible, to avoid re-enabling the CTMU current source. In addition to being set by the CTMU hardware, the Edge Status bits can also be set by software. This permits a user application to manually enable or disable the current source. Setting either (but not both) of the bits enables the current source. Setting or clearing both bits at once disables the source. DS30000575C-page 505 PIC18F97J94 FAMILY 26.2.5 INTERRUPTS The CTMU sets its interrupt flag (PIR3) whenever the current source is enabled, then disabled. An interrupt is generated only if the corresponding interrupt enable bit (PIE3) is also set. If edge sequencing is not enabled (i.e., Edge 1 must occur before Edge 2), it is necessary to monitor the Edge Status bits, and determine which edge occurred last and caused the interrupt. 26.3 CTMU Module Initialization The following sequence is a general guideline used to initialize the CTMU module: 1. 2. 3. 4. Select the current source range using the IRNGx bits (CTMUCON1). Adjust the current source trim using the ITRIMx bits (CTMUCON1). Configure the edge input sources for Edge 1 and Edge 2 by setting the EDG1SELx and EDG2SELx bits (CTMUCON3 and CTMUCON2, respectively). Configure the input polarities for the edge inputs using the EDG1POL and EDG2POL bits (CTMUCON3 and CTMUCON2). The default configuration is for negative edge polarity (high-to-low transitions). 5. Enable edge sequencing using the EDGSEQEN bit (CTMUCON). By default, edge sequencing is disabled. 6. Select the operating mode (Measurement or Time Delay) with the TGEN bit (CTMUCON). The default mode is Time/Capacitance Measurement mode. 7. Configure the module to automatically trigger an A/D conversion when the second edge event has occurred using the CTTRIG bit (CTMUCON). The conversion trigger is disabled by default. 8. Discharge the connected circuit by setting the IDISSEN bit (CTMUCON). 9. After waiting a sufficient time for the circuit to discharge, clear the IDISSEN bit. 10. Disable the module by clearing the CTMUEN bit (CTMUCON). 11. Clear the Edge Status bits, EDG2STAT and EDG1STAT (CTMUCON3). Both bits should be cleared simultaneously, if possible, to avoid re-enabling the CTMU current source. 12. Enable both edge inputs by setting the EDGEN bit (CTMUCON). 13. Enable the module by setting the CTMUEN bit. DS30000575C-page 506 Depending on the type of measurement or pulse generation being performed, one or more additional modules may also need to be initialized and configured with the CTMU module: • Edge Source Generation: In addition to the external edge input pins, CCP1/CCP2 Special Event Triggers can be used as edge sources for the CTMU. • Capacitance or Time Measurement: The CTMU module uses the A/D Converter to measure the voltage across a capacitor that is connected to one of the analog input channels. • Pulse Generation: When generating system clock independent, output pulses, the CTMU module uses Comparator 2 and the associated comparator voltage reference. 26.4 Calibrating the CTMU Module The CTMU requires calibration for precise measurements of capacitance and time, as well as for accurate time delay. If the application only requires measurement of a relative change in capacitance or time, calibration is usually not necessary. An example of a less precise application is a capacitive touch switch, in which the touch circuit has a baseline capacitance and the added capacitance of the human body changes the overall capacitance of a circuit. If actual capacitance or time measurement is required, two hardware calibrations must take place: • The current source needs calibration to set it to a precise current. • The circuit being measured needs calibration to measure or nullify any capacitance other than that to be measured. 26.4.1 CURRENT SOURCE CALIBRATION The current source on board the CTMU module has a range of ±62% nominal for each of three current ranges. For precise measurements, it is possible to measure and adjust this current source by placing a high-precision resistor, RCAL, onto an unused analog channel. An example circuit is shown in Figure 26-2. To measure the current source: 1. 2. 3. 4. 5. 6. Initialize the A/D Converter. Initialize the CTMU. Enable the current source by setting EDG1STAT (CTMUCON3). Issue time delay for voltage across RCAL to stabilize and the A/D Sample-and-Hold (S/H) capacitor to charge. Perform the A/D conversion. Calculate the current source current using I = V / RCAL, where RCAL is a high-precision resistance and V is measured by performing an A/D conversion.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY The CTMU current source may be trimmed with the ITRIMx bits in CTMUCON1, using an iterative process to get the exact current desired. Alternatively, the nominal value without adjustment may be used. That value may be stored by software for use in all subsequent capacitive or time measurements. To calculate the optimal value for RCAL, the nominal current must be chosen. For example, if the A/D Converter reference voltage is 3.3V, use 70% of full scale (or 2.31V) as the desired approximate voltage to be read by the A/D Converter. If the range of the CTMU current source is selected to be 0.55 A, the resistor value needed is calculated as RCAL = 2.31V/0.55 A, for a value of 4.2 MΩ. Similarly, if the current source is chosen to be 5.5 A, RCAL would be 420,000Ω, and 42,000Ω if the current source is set to 55 A. FIGURE 26-2: CTMU CURRENT SOURCE CALIBRATION CIRCUIT PIC18F97J94 Current Source A value of 70% of full-scale voltage is chosen to make sure that the A/D Converter is in a range that is well above the noise floor. If an exact current is chosen to incorporate the trimming bits from CTMUCON1, the resistor value of RCAL may need to be adjusted accordingly. RCAL also may be adjusted to allow for available resistor values. RCAL should be of the highest precision available in light of the precision needed for the circuit that the CTMU will be measuring. A recommended minimum would be 0.1% tolerance. The following examples show a typical method for performing a CTMU current calibration. • Example 26-1 demonstrates how to initialize the A/D Converter and the CTMU. This routine is typical for applications using both modules. • Example 26-2 demonstrates one method for the actual calibration routine. This method manually triggers the A/D Converter to demonstrate the entire step-wise process. It is also possible to automatically trigger the conversion by setting the CTMU’s CTTRIG bit (CTMUCON). CTMU A/D Trigger A/D Converter ANx RCAL A/D MUX  2012-2016 Microchip Technology Inc. DS30000575C-page 507 PIC18F97J94 FAMILY EXAMPLE 26-1: SETUP FOR CTMU CALIBRATION ROUTINES #include "p18cxxx.h" /**************************************************************************/ /*Setup CTMU *****************************************************************/ /**************************************************************************/ void setup(void) { //CTMUCON - CTMU Control register CTMUCON = 0x00; //make sure CTMU is disabled CTMUCON3 = 0x90; //CTMU continues to run when emulator is stopped,CTMU continues //to run in idle mode,Time Generation mode disabled, Edges are blocked //No edge sequence order, Analog current source not grounded, trigger //output disabled, Edge2 polarity = positive level, Edge2 source = //source 0, Edge1 polarity = positive level, Edge1 source = source 0, // Set Edge status bits to zero //CTMUCON1 - CTMU Current Control Register CTMUCON1 = 0x01; //0.55uA, Nominal - No Adjustment /**************************************************************************/ //Setup AD converter; /**************************************************************************/ TRISBbits.TRISB0=0; TRISAbits.TRISA2=1; ANCON1bits.ANSEL2=1; ADCON1Hbits.FORM=0b00; ADCON1Lbits.SSRC=0b0111; ADCON3Hbits.SAMC=0b00111; ADCON3Lbits.ADCS=0x3F; ADCON2Hbits.PVCFG=0b00; ADCON2Hbits.NVCFG0=0; ADCHS0Lbits.CHONA=0b000; ADCHS0Lbits.CHOSA=0b00010; ADCON1Hbits.ADON=1; // Turn on ADC //set channel 2 as an input // Configured AN2 as an analog channel // Result format 1= Right justified // // // // // Acquisition time 7 = 20TAD 2 = 4TAD 1=2TAD Clock conversion bits 6= FOSC/64 2=FOSC/32 ADCON1 Vref+ = AVdd Vref- = AVss // Select ADC channel } DS30000575C-page 508  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY EXAMPLE 26-2: CTMU CURRENT CALIBRATION ROUTINE #include "p18cxxx.h" #define COUNT 500 #define DELAY for(i=0;i 9] or [DC = 1], then (W) + 6  W; else (W)  W 0  f  255 d  [0,1] a  [0,1] Operation: (f) – 1  dest Status Affected: C, DC, N, OV, Z Encoding: If [W > 9] or [C = 1], then (W) + 6  W; C =1; else (W)  W Status Affected: Description: 0000 0000 0000 0111 Description: DAW adjusts the 8-bit value in W, resulting from the earlier addition of two variables (each in packed BCD format) and produces a correct packed BCD result. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register W Process Data Write W A5h 0 0 05h 1 0 ffff ffff Decrement register, ‘f’. If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination DAW Before Instruction W = C = DC = After Instruction W = C = DC = 01da If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. C Encoding: Example 1: 0000 Example: DECF Before Instruction CNT = Z = After Instruction CNT = Z = CNT, 1, 0 01h 0 00h 1 Example 2: Before Instruction W = C = DC = After Instruction W = C = DC = DS30000575C-page 584 CEh 0 0 34h 1 0  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY DECFSZ Decrement f, Skip if 0 DCFSNZ Decrement f, Skip if Not 0 Syntax: DECFSZ f {,d {,a}} Syntax: DCFSNZ Operands: 0  f  255 d  [0,1] a  [0,1] Operands: 0  f  255 d  [0,1] a  [0,1] Operation: (f) – 1  dest, skip if result = 0 Operation: (f) – 1  dest, skip if result  0 Status Affected: None Status Affected: None Encoding: 0010 Description: 11da ffff ffff The contents of register ‘f’ are decremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. Encoding: 0100 Description: If the result is ‘0’, the next instruction which is already fetched is discarded and a NOP is executed instead, making it a 2-cycle instruction. Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Q1 Q2 Q3 Q4 Read register ‘f’ Process Data Write to destination Q1 Q2 Q3 Q4 No operation No operation No operation No operation Words: 1 Cycles: 1(2) Note: Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation DECFSZ GOTO CNT, 1, 1 LOOP Example: HERE CONTINUE Before Instruction PC = After Instruction CNT = If CNT = PC = If CNT  PC = Address (HERE) CNT – 1 0; Address (CONTINUE) 0; Address (HERE + 2)  2012-2016 Microchip Technology Inc. 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination If skip: If skip and followed by 2-word instruction: ffff If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Q Cycle Activity: Decode ffff If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. 1 11da The contents of register ‘f’ are decremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. If the result is not ‘0’, the next instruction which is already fetched is discarded and a NOP is executed instead, making it a 2-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. Words: f {,d {,a}} If skip: Q1 Q2 Q3 Q4 No operation No operation No operation No operation If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE ZERO NZERO Before Instruction TEMP After Instruction TEMP If TEMP PC If TEMP PC DCFSNZ : : TEMP, 1, 0 = ? = = =  = TEMP – 1, 0; Address (ZERO) 0; Address (NZERO) DS30000575C-page 585 PIC18F97J94 FAMILY GOTO Unconditional Branch INCF Increment f Syntax: GOTO k Syntax: INCF Operands: 0  k  1048575 Operands: Operation: k  PC Status Affected: None 0  f  255 d  [0,1] a  [0,1] Operation: (f) + 1  dest Status Affected: C, DC, N, OV, Z Encoding: 1st word (k) 2nd word(k) 1110 1111 1111 k19kkk k7kkk kkkk kkkk0 kkkk8 Description: GOTO allows an unconditional branch anywhere within entire 2-Mbyte memory range. The 20-bit value ‘k’ is loaded into PC. GOTO is always a 2-cycle instruction. Words: 2 Cycles: 2 Encoding: 0010 Description: Q1 Q2 Q3 Q4 Read literal ‘k’, No operation Read literal ‘k’, Write to PC No operation No operation No operation No operation Example: GOTO THERE After Instruction PC = Address (THERE) ffff ffff The contents of register ‘f’ are incremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: INCF Before Instruction CNT = Z = C = DC = After Instruction CNT = Z = C = DC = DS30000575C-page 586 10da If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. Q Cycle Activity: Decode f {,d {,a}} CNT, 1, 0 FFh 0 ? ? 00h 1 1 1  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY INCFSZ Increment f, Skip if 0 INFSNZ Syntax: INCFSZ Syntax: INFSNZ 0  f  255 d  [0,1] a  [0,1] f {,d {,a}} Increment f, Skip if Not 0 f {,d {,a}} Operands: 0  f  255 d  [0,1] a  [0,1] Operands: Operation: (f) + 1  dest, skip if result = 0 Operation: (f) + 1  dest, skip if result  0 Status Affected: None Status Affected: None Encoding: 0011 Description: 11da ffff ffff The contents of register ‘f’ are incremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. Encoding: 0100 Description: 10da ffff ffff The contents of register ‘f’ are incremented. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. If the result is ‘0’, the next instruction which is already fetched is discarded and a NOP is executed instead, making it a 2-cycle instruction. If the result is not ‘0’, the next instruction which is already fetched is discarded and a NOP is executed instead, making it a 2-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Words: 1 Cycles: 1(2) Note: Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q Cycle Activity: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Decode Read register ‘f’ Process Data Write to destination Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation If skip: If skip: If skip and followed by 2-word instruction: If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE NZERO ZERO Before Instruction PC = After Instruction CNT = If CNT = PC = If CNT  PC = INCFSZ : : Address (HERE) CNT + 1 0; Address (ZERO) 0; Address (NZERO)  2012-2016 Microchip Technology Inc. CNT, 1, 0 Example: HERE ZERO NZERO Before Instruction PC = After Instruction REG = If REG  PC = If REG = PC = INFSNZ REG, 1, 0 Address (HERE) REG + 1 0; Address (NZERO) 0; Address (ZERO) DS30000575C-page 587 PIC18F97J94 FAMILY IORLW Inclusive OR Literal with W IORWF Inclusive OR W with f Syntax: IORLW k Syntax: IORWF Operands: 0  k  255 Operands: Operation: (W) .OR. k  W Status Affected: N, Z 0  f  255 d  [0,1] a  [0,1] Operation: (W) .OR. (f)  dest Status Affected: N, Z Encoding: 0000 1001 kkkk kkkk Description: The contents of W are ORed with the 8-bit literal ‘k’. The result is placed in W. Words: 1 Cycles: 1 Encoding: 0001 Description: Q1 Q2 Q3 Q4 Read literal ‘k’ Process Data Write to W Example: IORLW Before Instruction W = After Instruction W = ffff ffff Inclusive OR W with register ‘f’. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. 35h 9Ah BFh 00da If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. Q Cycle Activity: Decode f {,d {,a}} Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: IORWF Before Instruction RESULT = W = After Instruction RESULT = W = DS30000575C-page 588 RESULT, 0, 1 13h 91h 13h 93h  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY LFSR Load FSR MOVF Move f Syntax: LFSR f, k Syntax: MOVF Operands: 0f2 0  k  4095 Operands: Operation: k  FSRf 0  f  255 d  [0,1] a  [0,1] Status Affected: None Operation: f  dest Status Affected: N, Z Encoding: 1110 1111 1110 0000 00ff k7kkk k11kkk kkkk Description: The 12-bit literal ‘k’ is loaded into the file select register pointed to by ‘f’. Words: 2 Cycles: 2 Encoding: 0101 Description: Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ MSB Process Data Write literal ‘k’ MSB to FSRfH Decode Read literal ‘k’ LSB Process Data Write literal ‘k’ to FSRfL Example: After Instruction FSR2H FSR2L 03h ABh 00da ffff ffff The contents of register ‘f’ are moved to a destination dependent upon the status of ‘d’. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. Location ‘f’ can be anywhere in the 256-byte bank. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. LFSR 2, 3ABh = = f {,d {,a}} Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write W Example: MOVF Before Instruction REG W After Instruction REG W  2012-2016 Microchip Technology Inc. REG, 0, 0 = = 22h FFh = = 22h 22h DS30000575C-page 589 PIC18F97J94 FAMILY MOVFF Move f to f MOVLB Move Literal to Low Nibble in BSR Syntax: MOVFF fs,fd Syntax: MOVLB k Operands: 0  fs  4095 0  fd  4095 Operands: 0  k  255 Operation: k  BSR Status Affected: None Operation: (fs)  fd Status Affected: None Encoding: 1st word (source) 2nd word (destin.) Description: Encoding: 1100 1111 ffff ffff ffff ffff ffffs ffffd The contents of source register, ‘fs’, are moved to destination register ‘fd’. Location of source ‘fs’ can be anywhere in the 4096-byte data space (000h to FFFh) and location of destination ‘fd’ can also be anywhere from 000h to FFFh. Either source or destination can be W (a useful special situation). MOVFF is particularly useful for transferring a data memory location to a peripheral register (such as the transmit buffer or an I/O port). The MOVFF instruction cannot use the PCL, TOSU, TOSH or TOSL as the destination register Words: 2 Cycles: 2 0000 0001 kkkk kkkk Description: The 8-bit literal ‘k’ is loaded into the Bank Select Register (BSR). The value of BSR always remains ‘0’ regardless of the value of k7:k4. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write literal ‘k’ to BSR MOVLB 5 Example: Before Instruction BSR Register = After Instruction BSR Register = 02h 05h Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ (src) Process Data No operation Decode No operation No operation Write register ‘f’ (dest) No dummy read Example: MOVFF Before Instruction REG1 REG2 After Instruction REG1 REG2 DS30000575C-page 590 REG1, REG2 = = 33h 11h = = 33h 33h  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY MOVLW Move Literal to W MOVWF Move W to f Syntax: MOVLW k Syntax: MOVWF Operands: 0  k  255 Operands: Operation: kW 0  f  255 a  [0,1] Status Affected: None Encoding: 0000 Description: 1110 kkkk kkkk The 8-bit literal ‘k’ is loaded into W. Words: 1 Cycles: 1 Operation: (W)  f Status Affected: None Encoding: 0110 Description: Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write to W Example: After Instruction W = MOVLW f {,a} 111a ffff ffff Move data from W to register ‘f’. Location ‘f’ can be anywhere in the 256-byte bank. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. 5Ah 5Ah Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ Example: MOVWF Before Instruction W = REG = After Instruction W = REG =  2012-2016 Microchip Technology Inc. REG, 0 4Fh FFh 4Fh 4Fh DS30000575C-page 591 PIC18F97J94 FAMILY MULLW Multiply Literal with W MULWF Multiply W with f Syntax: MULLW Syntax: MULWF Operands: 0  f  255 a  [0,1] Operation: (W) x (f)  PRODH:PRODL Status Affected: None k Operands: 0  k  255 Operation: (W) x k  PRODH:PRODL Status Affected: None Encoding: 0000 Description: 1101 kkkk kkkk An unsigned multiplication is carried out between the contents of W and the 8-bit literal ‘k’. The 16-bit result is placed in the PRODH:PRODL register pair. PRODH contains the high byte. Encoding: 0000 Description: W is unchanged. None of the Status flags are affected. 1 Cycles: 1 ffff ffff Note that neither Overflow nor Carry is possible in this operation. A Zero result is possible but not detected. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write registers PRODH: PRODL Example: 001a An unsigned multiplication is carried out between the contents of W and the register file location ‘f’. The 16-bit result is stored in the PRODH:PRODL register pair. PRODH contains the high byte. Both W and ‘f’ are unchanged. None of the Status flags are affected. Note that neither Overflow nor Carry is possible in this operation. A Zero result is possible but not detected. Words: f {,a} MULLW Before Instruction W PRODH PRODL After Instruction W PRODH PRODL = = = = = = 0C4h E2h ? ? E2h ADh 08h If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and BitOriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write registers PRODH: PRODL Example: MULWF Before Instruction W REG PRODH PRODL After Instruction W REG PRODH PRODL DS30000575C-page 592 REG, 1 = = = = C4h B5h ? ? = = = = C4h B5h 8Ah 94h  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY NEGF Negate f Syntax: NEGF Operands: 0  f  255 a  [0,1] f {,a} Operation: (f) + 1  f Status Affected: N, OV, C, DC, Z Encoding: 0110 Description: 110a ffff If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. 1 1 Syntax: NOP Operands: None Operation: No operation Status Affected: None 0000 1111 ffff If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. Cycles: No Operation Encoding: Location ‘f’ is negated using two’s complement. The result is placed in the data memory location ‘f’. Words: NOP 0000 xxxx Description: No operation. Words: 1 Cycles: 1 0000 xxxx 0000 xxxx Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation No operation No operation Example: None. Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ Example: NEGF Before Instruction REG = After Instruction REG = REG, 1 0011 1010 [3Ah] 1100 0110 [C6h]  2012-2016 Microchip Technology Inc. DS30000575C-page 593 PIC18F97J94 FAMILY POP Pop Top of Return Stack PUSH Push Top of Return Stack Syntax: POP Syntax: PUSH Operands: None Operands: None Operation: (TOS)  bit bucket Operation: (PC + 2)  TOS Status Affected: None Status Affected: None Encoding: 0000 0000 0000 0110 Encoding: 0000 0000 0000 0101 Description: The TOS value is pulled off the return stack and is discarded. The TOS value then becomes the previous value that was pushed onto the return stack. This instruction is provided to enable the user to properly manage the return stack to incorporate a software stack. Description: The PC + 2 is pushed onto the top of the return stack. The previous TOS value is pushed down on the stack. This instruction allows implementing a software stack by modifying TOS and then pushing it onto the return stack. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Q Cycle Activity: Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation POP TOS value No operation POP GOTO NEW Example: Q2 Q3 Q4 PUSH PC + 2 onto return stack No operation No operation Example: Before Instruction TOS Stack (1 level down) = = 0031A2h 014332h After Instruction TOS PC = = 014332h NEW DS30000575C-page 594 Q1 Decode PUSH Before Instruction TOS PC = = 345Ah 0124h After Instruction PC TOS Stack (1 level down) = = = 0126h 0126h 345Ah  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY RCALL Relative Call RESET Reset Syntax: RCALL Syntax: RESET n Operands: -1024  n  1023 Operands: None Operation: (PC) + 2  TOS, (PC) + 2 + 2n  PC Operation: Reset all registers and flags that are affected by a MCLR Reset. Status Affected: None Status Affected: All Encoding: 1101 Description: 1nnn nnnn nnnn Subroutine call with a jump up to 1K from the current location. First, return address (PC + 2) is pushed onto the stack. Then, add the 2’s complement number ‘2n’ to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is a 2-cycle instruction. Words: 1 Cycles: 2 Encoding: 0000 Q1 Q2 Q3 Q4 Decode Read literal ‘n’ Process Data Write to PC No operation No operation 1111 1111 This instruction provides a way to execute a MCLR Reset in software. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Start reset No operation No operation Example: Q Cycle Activity: 0000 Description: After Instruction Registers = Flags* = RESET Reset Value Reset Value PUSH PC to stack No operation Example: No operation HERE RCALL Jump Before Instruction PC = Address (HERE) After Instruction PC = Address (Jump) TOS = Address (HERE + 2)  2012-2016 Microchip Technology Inc. DS30000575C-page 595 PIC18F97J94 FAMILY RETFIE Return from Interrupt RETLW Return Literal to W Syntax: RETFIE {s} Syntax: RETLW k Operands: s  [0,1] Operands: 0  k  255 Operation: (TOS)  PC, 1  GIE/GIEH or PEIE/GIEL; if s = 1, (WS)  W, (STATUSS)  STATUS, (BSRS)  BSR, PCLATU, PCLATH are unchanged Operation: k  W, (TOS)  PC, PCLATU, PCLATH are unchanged Status Affected: None Status Affected: 0000 0000 0001 1 Cycles: 2 Q Cycle Activity: kkkk kkkk W is loaded with the 8-bit literal ‘k’. The Program Counter is loaded from the top of the stack (the return address). The high address latch (PCLATH) remains unchanged. Words: 1 Cycles: 2 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data POP PC from stack, write to W No operation No operation No operation No operation Example: Q1 Q2 Q3 Q4 Decode No operation No operation POP PC from stack Set GIEH or GIEL Example: 1100 Description: 000s Return from interrupt. Stack is popped and Top-of-Stack (TOS) is loaded into the PC. Interrupts are enabled by setting either the high or low-priority Global Interrupt Enable bit. If ‘s’ = 1, the contents of the shadow registers WS, STATUSS and BSRS are loaded into their corresponding registers W, STATUS and BSR. If ‘s’ = 0, no update of these registers occurs. Words: No operation 0000 GIE/GIEH, PEIE/GIEL. Encoding: Description: Encoding: No operation RETFIE After Interrupt PC W BSR STATUS GIE/GIEH, PEIE/GIEL DS30000575C-page 596 No operation No operation 1 = = = = = TOS WS BSRS STATUSS 1 CALL TABLE ; ; ; ; : TABLE ADDWF PCL ; RETLW k0 ; RETLW k1 ; : : RETLW kn ; Before Instruction W = After Instruction W = W contains table offset value W now has table value W = offset Begin table End of table 07h value of kn  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY RETURN Return from Subroutine RLCF Rotate Left f through Carry Syntax: RETURN {s} Syntax: RLCF Operands: s  [0,1] Operands: Operation: (TOS)  PC; if s = 1, (WS)  W, (STATUSS)  STATUS, (BSRS)  BSR, PCLATU, PCLATH are unchanged 0  f  255 d  [0,1] a  [0,1] Operation: (f)  dest, (f)  C, (C)  dest Status Affected: C, N, Z Status Affected: None Encoding: 0000 Description: Encoding: 0000 0001 001s 0011 Description: Return from subroutine. The stack is popped and the top of the stack (TOS) is loaded into the Program Counter. If ‘s’= 1, the contents of the shadow registers WS, STATUSS and BSRS are loaded into their corresponding registers W, STATUS and BSR. If ‘s’ = 0, no update of these registers occurs. Words: 1 Cycles: 2 Q1 Q2 Q3 Q4 No operation Process Data POP PC from stack No operation No operation No operation No operation 01da ffff ffff The contents of register ‘f’ are rotated one bit to the left through the Carry flag. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and BitOriented Instructions in Indexed Literal Offset Mode” for details. Q Cycle Activity: Decode f {,d {,a}} register f C Words: 1 Cycles: 1 Q Cycle Activity: Example: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination RETURN After Instruction: PC = TOS Example: Before Instruction REG = C = After Instruction REG = W = C =  2012-2016 Microchip Technology Inc. RLCF REG, 0, 0 1110 0110 0 1110 0110 1100 1100 1 DS30000575C-page 597 PIC18F97J94 FAMILY RLNCF Rotate Left f (No Carry) RRCF Rotate Right f through Carry Syntax: RLNCF Syntax: RRCF Operands: 0  f  255 d  [0,1] a  [0,1] Operands: 0  f  255 d  [0,1] a  [0,1] Operation: (f)  dest, (f)  dest Operation: Status Affected: N, Z (f)  dest, (f)  C, (C)  dest Status Affected: C, N, Z Encoding: 0100 Description: f {,d {,a}} 01da ffff ffff The contents of register ‘f’ are rotated one bit to the left. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’. Encoding: 0011 Description: If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. Cycles: 1 Q1 Decode Q2 Read register ‘f’ Example: RLNCF Before Instruction REG = After Instruction REG = DS30000575C-page 598 Q3 Process Data Q4 Write to destination Words: 1 Cycles: register f 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination REG, 1, 0 1010 1011 0101 0111 ffff The contents of register ‘f’ are rotated one bit to the right through the Carry flag. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. C Q Cycle Activity: ffff If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. register f 1 00da If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: f {,d {,a}} Example: RRCF Before Instruction REG = C = After Instruction REG = W = C = REG, 0, 0 1110 0110 0 1110 0110 0111 0011 0  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY RRNCF Rotate Right f (No Carry) SETF Set f Syntax: RRNCF Syntax: SETF Operands: 0  f  255 d  [0,1] a  [0,1] Operands: 0  f  255 a [0,1] Operation: (f)  dest, (f)  dest Status Affected: N, Z Encoding: 0100 Description: f {,d {,a}} 00da Operation: FFh  f Status Affected: None Encoding: ffff ffff 0110 Description: The contents of register ‘f’ are rotated one bit to the right. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed back in register ‘f’. register f Words: 1 Cycles: 1 Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example 1: RRNCF Before Instruction REG = After Instruction REG = Example 2: ffff Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write register ‘f’ SETF Before Instruction REG After Instruction REG REG,1 = 5Ah = FFh REG, 1, 0 1101 0111 1110 1011 RRNCF Before Instruction W = REG = After Instruction W = REG = ffff If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Example: Q Cycle Activity: 100a The contents of the specified register are set to FFh. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’, the Access Bank will be selected, overriding the BSR value. If ‘a’ is ‘1’, then the bank will be selected as per the BSR value. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. f {,a} REG, 0, 0 ? 1101 0111 1110 1011 1101 0111  2012-2016 Microchip Technology Inc. DS30000575C-page 599 PIC18F97J94 FAMILY SLEEP Enter Sleep Mode SUBFWB Subtract f from W with Borrow Syntax: SLEEP Syntax: SUBFWB Operands: None Operands: Operation: 00h  WDT, 0  WDT postscaler, 1  TO, 0  PD 0 f 255 d  [0,1] a  [0,1] Operation: (W) – (f) – (C) dest Status Affected: N, OV, C, DC, Z Status Affected: TO, PD Encoding: 0000 Encoding: 0000 0000 0011 0101 Description: The Power-Down Status bit (PD) is cleared. The Time-out Status bit (TO) is set. The Watchdog Timer and its postscaler are cleared. Description: 1 Cycles: 1 Q1 Q2 Q3 Q4 No operation Process Data Go to Sleep Example: SLEEP Before Instruction TO = ? ? PD = After Instruction 1† TO = 0 PD = † If WDT causes wake-up, this bit is cleared. DS30000575C-page 600 ffff ffff Subtract register ‘f’ and Carry flag (borrow) from W (2’s complement method). If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored in register ‘f’. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and BitOriented Instructions in Indexed Literal Offset Mode” for details. Q Cycle Activity: Decode 01da If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. The processor is put into Sleep mode with the oscillator stopped. Words: f {,d {,a}} Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example 1: SUBFWB REG, 1, 0 Before Instruction REG = 3 W = 2 C = 1 After Instruction REG = FF W = 2 C = 0 Z = 0 N = 1 ; result is negative Example 2: SUBFWB REG, 0, 0 Before Instruction REG = 2 W = 5 C = 1 After Instruction REG = 2 W = 3 C = 1 Z = 0 N = 0 ; result is positive SUBFWB REG, 1, 0 Example 3: Before Instruction REG = 1 W = 2 C = 0 After Instruction REG = 0 W = 2 C = 1 Z = 1 ; result is zero N = 0  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY SUBLW Subtract W from Literal SUBWF Subtract W from f Syntax: SUBLW k Syntax: SUBWF Operands: 0 k 255 Operands: Operation: k – (W) W Status Affected: N, OV, C, DC, Z 0 f 255 d  [0,1] a  [0,1] Operation: (f) – (W) dest Status Affected: N, OV, C, DC, Z Encoding: 0000 1000 kkkk kkkk Description: W is subtracted from the 8-bit literal ‘k’. The result is placed in W. Words: 1 Cycles: 1 Encoding: 0101 Description: Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write to W Example 1: Before Instruction W = C = After Instruction W = C = Z = N = Example 2: Before Instruction W = C = After Instruction W = C = Z = N = Example 3: Before Instruction W = C = After Instruction W = C = Z = N = SUBLW SUBLW ; result is positive 02h ? 00h 1 1 0 SUBLW ; result is zero 02h 03h ? FFh 0 0 1 ; (2’s complement) ; result is negative ffff Subtract W from register ‘f’ (2’s complement method). If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination SUBWF REG, 1, 0 Example 1: Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 2: Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 3: Before Instruction REG = W = C = After Instruction REG = W = C = Z = N =  2012-2016 Microchip Technology Inc. ffff If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and BitOriented Instructions in Indexed Literal Offset Mode” for details. 02h 02h 11da If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. 01h ? 01h 1 0 0 f {,d {,a}} 3 2 ? 1 2 1 0 0 ; result is positive SUBWF REG, 0, 0 2 2 ? 2 0 1 1 0 SUBWF ; result is zero REG, 1, 0 1 2 ? FFh ;(2’s complement) 2 0 ; result is negative 0 1 DS30000575C-page 601 PIC18F97J94 FAMILY SUBWFB Subtract W from f with Borrow SWAPF Swap f Syntax: SUBWFB Syntax: SWAPF f {,d {,a}} Operands: 0  f  255 d  [0,1] a  [0,1] Operands: 0  f  255 d  [0,1] a  [0,1] Operation: (f) – (W) – (C) dest Operation: Status Affected: N, OV, C, DC, Z (f)  dest, (f)  dest Status Affected: None Encoding: 0101 Description: f {,d {,a}} 10da ffff ffff Subtract W and the Carry flag (borrow) from register ‘f’ (2’s complement method). If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’. Encoding: 0011 Description: If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. 1 Cycles: 1 Q Cycle Activity: Q1 Decode Q2 Read register ‘f’ Example 1: SUBWFB Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 2: Q4 Write to destination If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination REG, 1, 0 19h 0Dh 1 (0001 1001) (0000 1101) 0Ch 0Dh 1 0 0 (0000 1011) (0000 1101) ffff Example: SWAPF Before Instruction REG = After Instruction REG = REG, 1, 0 53h 35h ; result is positive SUBWFB REG, 0, 0 Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 3: 1Bh 1Ah 0 (0001 1011) (0001 1010) 1Bh 00h 1 1 0 (0001 1011) SUBWFB Before Instruction REG = W = C = After Instruction REG = W C Z N Q3 Process Data ffff If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 10da The upper and lower nibbles of register ‘f’ are exchanged. If ‘d’ is ‘0’, the result is placed in W. If ‘d’ is ‘1’, the result is placed in register ‘f’. = = = = DS30000575C-page 602 ; result is zero REG, 1, 0 03h 0Eh 1 (0000 0011) (0000 1101) F5h (1111 0100) ; [2’s comp] (0000 1101) 0Eh 0 0 1 ; result is negative  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TBLRD Table Read TBLRD Table Read (Continued) Syntax: TBLRD ( *; *+; *-; +*) Example 1: TBLRD Operands: None Operation: if TBLRD *, (Prog Mem (TBLPTR))  TABLAT; TBLPTR – No Change if TBLRD *+, (Prog Mem (TBLPTR))  TABLAT; (TBLPTR) + 1  TBLPTR if TBLRD *-, (Prog Mem (TBLPTR))  TABLAT; (TBLPTR) – 1  TBLPTR if TBLRD +*, (TBLPTR) + 1  TBLPTR; (Prog Mem (TBLPTR))  TABLAT Status Affected: None Encoding: Description: 0000 0000 0000 Before Instruction TABLAT TBLPTR MEMORY(00A356h) After Instruction TABLAT TBLPTR Example 2: TBLRD Before Instruction TABLAT TBLPTR MEMORY(01A357h) MEMORY(01A358h) After Instruction TABLAT TBLPTR *+ ; = = = 55h 00A356h 34h = = 34h 00A357h +* ; = = = = AAh 01A357h 12h 34h = = 34h 01A358h 10nn nn=0 * =1 *+ =2 *=3 +* This instruction is used to read the contents of Program Memory (P.M.). To address the program memory, a pointer called Table Pointer (TBLPTR) is used. The TBLPTR (a 21-bit pointer) points to each byte in the program memory. TBLPTR has a 2-Mbyte address range. TBLPTR = 0:Least Significant Byte of Program Memory Word TBLPTR = 1:Most Significant Byte of Program Memory Word The TBLRD instruction can modify the value of TBLPTR as follows: • no change • post-increment • post-decrement • pre-increment Words: 1 Cycles: 2 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation No operation No operation No operation No operation (Read Program Memory) No operation No operation (Write TABLAT)  2012-2016 Microchip Technology Inc. DS30000575C-page 603 PIC18F97J94 FAMILY TBLWT Table Write TBLWT Table Write (Continued) Syntax: TBLWT ( *; *+; *-; +*) Example 1: TBLWT *+; Operands: None Operation: if TBLWT*, (TABLAT)  Holding Register; TBLPTR – No Change if TBLWT*+, (TABLAT)  Holding Register; (TBLPTR) + 1  TBLPTR if TBLWT*-, (TABLAT)  Holding Register; (TBLPTR) – 1  TBLPTR if TBLWT+*, (TBLPTR) + 1  TBLPTR; (TABLAT)  Holding Register Status Affected: Example 2: None Encoding: Description: Before Instruction TABLAT = 55h TBLPTR = 00A356h HOLDING REGISTER (00A356h) = FFh After Instructions (table write completion) TABLAT = 55h TBLPTR = 00A357h HOLDING REGISTER (00A356h) = 55h 0000 0000 0000 11nn nn=0 * =1 *+ =2 *=3 +* This instruction uses the 3 LSBs of TBLPTR to determine which of the 8 holding registers the TABLAT is written to. The holding registers are used to program the contents of Program Memory (P.M.). (Refer to Section 6.0 “Memory Organization” for additional details on programming Flash memory.) TBLWT +*; Before Instruction TABLAT = 34h TBLPTR = 01389Ah HOLDING REGISTER (01389Ah) = FFh HOLDING REGISTER (01389Bh) = FFh After Instruction (table write completion) TABLAT = 34h TBLPTR = 01389Bh HOLDING REGISTER (01389Ah) = FFh HOLDING REGISTER (01389Bh) = 34h The TBLPTR (a 21-bit pointer) points to each byte in the program memory. TBLPTR has a 2-Mbyte address range. The LSb of the TBLPTR selects which byte of the program memory location to access. TBLPTR[0] = 0:Least Significant Byte of Program Memory Word TBLPTR[0] = 1:Most Significant Byte of Program Memory Word The TBLWT instruction can modify the value of TBLPTR as follows: • • • • no change post-increment post-decrement pre-increment Words: 1 Cycles: 2 Q Cycle Activity: Q1 Decode Q2 Q3 Q4 No No No operation operation operation No No No No operation operation operation operation (Write to (Read Holding TABLAT) Register) DS30000575C-page 604  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TSTFSZ Test f, Skip if 0 XORLW Exclusive OR Literal with W Syntax: TSTFSZ f {,a} Syntax: XORLW k Operands: 0  f  255 a  [0,1] Operands: 0 k 255 Operation: (W) .XOR. k W Status Affected: N, Z Operation: skip if f = 0 Status Affected: None Encoding: Encoding: 0110 Description: 011a ffff ffff If ‘f’ = 0, the next instruction fetched during the current instruction execution is discarded and a NOP is executed, making this a 2-cycle instruction. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. 0000 1010 kkkk kkkk Description: The contents of W are XORed with the 8-bit literal ‘k’. The result is placed in W. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write to W Example: Before Instruction W = After Instruction W = XORLW 0AFh B5h 1Ah Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data No operation If skip: Q1 Q2 Q3 Q4 No operation No operation No operation No operation If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE NZERO ZERO Before Instruction PC After Instruction If CNT PC If CNT PC TSTFSZ : : CNT, 1 = Address (HERE) = =  = 00h, Address (ZERO) 00h, Address (NZERO)  2012-2016 Microchip Technology Inc. DS30000575C-page 605 PIC18F97J94 FAMILY XORWF Exclusive OR W with f Syntax: XORWF Operands: 0  f  255 d  [0,1] a  [0,1] Operation: (W) .XOR. (f) dest Status Affected: N, Z Encoding: 0001 Description: f {,d {,a}} 10da ffff ffff Exclusive OR the contents of W with register ‘f’. If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in the register ‘f’. If ‘a’ is ‘0’, the Access Bank is selected. If ‘a’ is ‘1’, the BSR is used to select the GPR bank. If ‘a’ is ‘0’ and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 29.2.3 “Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode” for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Example: XORWF Before Instruction REG = W = After Instruction REG = W = DS30000575C-page 606 REG, 1, 0 AFh B5h 1Ah B5h  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 29.2 Extended Instruction Set A summary of the instructions in the extended instruction set is provided in Table 29-3. Detailed descriptions are provided in Section 29.2.2 “Extended Instruction Set”. The opcode field descriptions in Table 29-1 (page 566) apply to both the standard and extended PIC18 instruction sets. In addition to the standard 75 instructions of the PIC18 instruction set, the PIC18FXXJ94 of devices also provides an optional extension to the core CPU functionality. The added features include eight additional instructions that augment Indirect and Indexed Addressing operations and the implementation of Indexed Literal Offset Addressing for many of the standard PIC18 instructions. Note: The additional features of the extended instruction set are enabled by default on unprogrammed devices. Users must properly set or clear the XINST Configuration bit during programming to enable or disable these features. The instructions in the extended set can all be classified as literal operations, which either manipulate the File Select Registers, or use them for Indexed Addressing. Two of the instructions, ADDFSR and SUBFSR, each have an additional special instantiation for using FSR2. These versions (ADDULNK and SUBULNK) allow for automatic return after execution. 29.2.1 EXTENDED INSTRUCTION SYNTAX Most of the extended instructions use indexed arguments, using one of the File Select Registers and some offset to specify a source or destination register. When an argument for an instruction serves as part of Indexed Addressing, it is enclosed in square brackets (“[ ]”). This is done to indicate that the argument is used as an index or offset. The MPASM™ Assembler will flag an error if it determines that an index or offset value is not bracketed. The extended instructions are specifically implemented to optimize re-entrant program code (that is, code that is recursive or that uses a software stack) written in high-level languages, particularly C. Among other things, they allow users working in high-level languages to perform certain operations on data structures more efficiently. These include: When the extended instruction set is enabled, brackets are also used to indicate index arguments in byteoriented and bit-oriented instructions. This is in addition to other changes in their syntax. For more details, see Section 29.2.3.1 “Extended Instruction Syntax with Standard PIC18 Commands”. • Dynamic allocation and deallocation of software stack space when entering and leaving subroutines • Function Pointer invocation • Software Stack Pointer manipulation • Manipulation of variables located in a software stack TABLE 29-3: The instruction set extension and the Indexed Literal Offset Addressing mode were designed for optimizing applications written in C; the user may likely never use these instructions directly in assembler. The syntax for these commands is provided as a reference for users who may be reviewing code that has been generated by a compiler. Note: In the past, square brackets have been used to denote optional arguments in the PIC18 and earlier instruction sets. In this text and going forward, optional arguments are denoted by braces (“{ }”). EXTENSIONS TO THE PIC18 INSTRUCTION SET Mnemonic, Operands ADDFSR ADDULNK CALLW MOVSF f, k k MOVSS zs, zd PUSHL k SUBFSR SUBULNK f, k k zs, fd Description Add Literal to FSR Add Literal to FSR2 and Return Call Subroutine using WREG Move zs (source) to 1st word fd (destination) 2nd word Move zs (source) to 1st word zd (destination) 2nd word Store Literal at FSR2, Decrement FSR2 Subtract Literal from FSR Subtract Literal from FSR2 and return  2012-2016 Microchip Technology Inc. Cycles 1 2 2 2 16-Bit Instruction Word MSb LSb Status Affected 1000 1000 0000 1011 ffff 1011 xxxx 1010 ffkk 11kk 0001 0zzz ffff 1zzz xzzz kkkk kkkk kkkk 0100 zzzz ffff zzzz zzzz kkkk None None None None 1 1110 1110 0000 1110 1111 1110 1111 1110 1 2 1110 1110 1001 1001 ffkk 11kk kkkk kkkk None None 2 None None DS30000575C-page 607 PIC18F97J94 FAMILY 29.2.2 EXTENDED INSTRUCTION SET ADDFSR Add Literal to FSR ADDULNK Syntax: ADDFSR f, k Syntax: ADDULNK k Operands: 0  k  63 f  [ 0, 1, 2 ] Operands: 0  k  63 Operation: Operation: FSR(f) + k  FSR(f) FSR2 + k  FSR2, (TOS) PC Status Affected: None Status Affected: None Encoding: 1110 1000 ffkk kkkk Description: The 6-bit literal ‘k’ is added to the contents of the FSR specified by ‘f’. Words: 1 Cycles: 1 Add Literal to FSR2 and Return Encoding: 1110 Description: Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write to FSR Example: After Instruction FSR2 = 03FFh Words: 1 Cycles: 2 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal ‘k’ Process Data Write to FSR No Operation No Operation No Operation No Operation 0422h Example: Note: kkkk This may be thought of as a special case of the ADDFSR instruction, where f = 3 (binary ‘11’); it operates only on FSR2. ADDFSR 2, 23h Before Instruction FSR2 = 11kk The instruction takes two cycles to execute; a NOP is performed during the second cycle. Q Cycle Activity: Q1 1000 The 6-bit literal ‘k’ is added to the contents of FSR2. A RETURN is then executed by loading the PC with the TOS. ADDULNK 23h Before Instruction FSR2 = PC = 03FFh 0100h After Instruction FSR2 = PC = 0422h (TOS) All PIC18 instructions may take an optional label argument preceding the instruction mnemonic for use in symbolic addressing. If a label is used, the instruction format then becomes: {label} instruction argument(s). DS30000575C-page 608  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY CALLW Subroutine Call Using WREG MOVSF Move Indexed to f Syntax: CALLW Syntax: MOVSF [zs], fd Operands: None Operands: Operation: (PC + 2)  TOS, (W)  PCL, (PCLATH)  PCH, (PCLATU)  PCU 0  zs  127 0  fd  4095 Operation: ((FSR2) + zs)  fd Status Affected: None Status Affected: None Encoding: 0000 Description 0000 0001 0100 First, the return address (PC + 2) is pushed onto the return stack. Next, the contents of W are written to PCL; the existing value is discarded. Then, the contents of PCLATH and PCLATU are latched into PCH and PCU, respectively. The second cycle is executed as a NOP instruction while the new next instruction is fetched. Encoding: 1st word (source) 2nd word (destin.) Description: Unlike CALL, there is no option to update W, STATUS or BSR. Words: 1 Cycles: 2 Q1 Q2 Q3 Q4 Read WREG Push PC to stack No operation No operation No operation No operation No operation Before Instruction PC = PCLATH = PCLATU = W = After Instruction PC = TOS = PCLATH = PCLATU = W = Words: 2 Cycles: 2 Q Cycle Activity: CALLW Decode address (HERE) 10h 00h 06h 001006h address (HERE + 2) 10h 00h 06h  2012-2016 Microchip Technology Inc. zzzzs ffffd If the resultant source address points to an Indirect Addressing register, the value returned will be 00h. Decode HERE 0zzz ffff The contents of the source register are moved to destination register ‘fd’. The actual address of the source register is determined by adding the 7-bit literal offset ‘zs’, in the first word, to the value of FSR2. The address of the destination register is specified by the 12-bit literal ‘fd’ in the second word. Both addresses can be anywhere in the 4096-byte data space (000h to FFFh). Q1 Example: 1011 ffff The MOVSF instruction cannot use the PCL, TOSU, TOSH or TOSL as the destination register. Q Cycle Activity: Decode 1110 1111 Q2 Q3 Determine Determine source addr source addr No operation No operation No dummy read Example: MOVSF Before Instruction FSR2 Contents of 85h REG2 After Instruction FSR2 Contents of 85h REG2 Q4 Read source reg Write register ‘f’ (dest) [05h], REG2 = 80h = = 33h 11h = 80h = = 33h 33h DS30000575C-page 609 PIC18F97J94 FAMILY MOVSS Move Indexed to Indexed PUSHL Store Literal at FSR2, Decrement FSR2 Syntax: MOVSS [zs], [zd] Syntax: PUSHL k Operands: 0  zs  127 0  zd  127 Operands: 0k  255 Operation: k  (FSR2), FSR2 – 1  FSR2 Status Affected: None Operation: ((FSR2) + zs)  ((FSR2) + zd) Status Affected: None Encoding: 1st word (source) 2nd word (dest.) Description 1110 1111 1011 xxxx 1zzz xzzz zzzzs zzzzd The contents of the source register are moved to the destination register. The addresses of the source and destination registers are determined by adding the 7-bit literal offsets, ‘zs’ or ‘zd’, respectively, to the value of FSR2. Both registers can be located anywhere in the 4096-byte data memory space (000h to FFFh). The MOVSS instruction cannot use the PCL, TOSU, TOSH or TOSL as the destination register. If the resultant source address points to an Indirect Addressing register, the value returned will be 00h. If the resultant destination address points to an Indirect Addressing register, the instruction will execute as a NOP. Words: 2 Cycles: 2 Q Cycle Activity: Q1 Decode Decode Example: Q2 Q3 Determine Determine source addr source addr Determine dest addr Determine dest addr Encoding: 1111 Description: 1010 kkkk kkkk The 8-bit literal ‘k’ is written to the data memory address specified by FSR2. FSR2 is decremented by 1 after the operation. This instruction allows users to push values onto a software stack. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read ‘k’ Process data Write to destination Example: PUSHL 08h Before Instruction FSR2H:FSR2L Memory (01ECh) = = 01ECh 00h After Instruction FSR2H:FSR2L Memory (01ECh) = = 01EBh 08h Q4 Read source reg Write to dest reg MOVSS [05h], [06h] Before Instruction FSR2 Contents of 85h Contents of 86h After Instruction FSR2 Contents of 85h Contents of 86h DS30000575C-page 610 = 80h = 33h = 11h = 80h = 33h = 33h  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY SUBFSR Subtract Literal from FSR SUBULNK Syntax: SUBFSR f, k Syntax: SUBULNK k Operands: 0  k  63 Operands: 0  k  63 f  [ 0, 1, 2 ] Operation: Operation: FSRf – k  FSRf FSR2 – k  FSR2, (TOS) PC Status Affected: None Status Affected: None Encoding: 1110 1001 ffkk kkkk Description: The 6-bit literal ‘k’ is subtracted from the contents of the FSR specified by ‘f’. Words: 1 Cycles: 1 Encoding: 1110 Description: Q1 Q2 Q3 Q4 Read register ‘f’ Process Data Write to destination Example: Before Instruction FSR2 = After Instruction FSR2 = SUBFSR 2, 23h 1001 11kk kkkk The 6-bit literal ‘k’ is subtracted from the contents of the FSR2. A RETURN is then executed by loading the PC with the TOS. The instruction takes two cycles to execute; a NOP is performed during the second cycle. Q Cycle Activity: Decode Subtract Literal from FSR2 and Return This may be thought of as a special case of the SUBFSR instruction, where f = 3 (binary ‘11’); it operates only on FSR2. Words: 1 Cycles: 2 Q Cycle Activity: 03FFh 03DCh Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination No Operation No Operation No Operation No Operation Example:  2012-2016 Microchip Technology Inc. SUBULNK 23h Before Instruction FSR2 = PC = 03FFh 0100h After Instruction FSR2 = PC = 03DCh (TOS) DS30000575C-page 611 PIC18F97J94 FAMILY 29.2.3 Note: BYTE-ORIENTED AND BITORIENTED INSTRUCTIONS IN INDEXED LITERAL OFFSET MODE Enabling the PIC18 instruction set extension may cause legacy applications to behave erratically or fail entirely. In addition to eight new commands in the extended set, enabling the extended instruction set also enables Indexed Literal Offset Addressing (Section 6.6.1 “Indexed Addressing with Literal Offset”). This has a significant impact on the way that many commands of the standard PIC18 instruction set are interpreted. When the extended set is disabled, addresses embedded in opcodes are treated as literal memory locations: either as a location in the Access Bank (a = 0) or in a GPR bank designated by the BSR (a = 1). When the extended instruction set is enabled and a = 0, however, a file register argument of 5Fh or less is interpreted as an offset from the pointer value in FSR2 and not as a literal address. For practical purposes, this means that all instructions that use the Access RAM bit as an argument – that is, all byte-oriented and bit-oriented instructions, or almost half of the core PIC18 instructions – may behave differently when the extended instruction set is enabled. When the content of FSR2 is 00h, the boundaries of the Access RAM are essentially remapped to their original values. This may be useful in creating backward compatible code. If this technique is used, it may be necessary to save the value of FSR2 and restore it when moving back and forth between C and assembly routines in order to preserve the Stack Pointer. Users must also keep in mind the syntax requirements of the extended instruction set (see Section 29.2.3.1 “Extended Instruction Syntax with Standard PIC18 Commands”). Although the Indexed Literal Offset mode can be very useful for dynamic stack and pointer manipulation, it can also be very annoying if a simple arithmetic operation is carried out on the wrong register. Users who are accustomed to the PIC18 programming must keep in mind, that when the extended instruction set is enabled, register addresses of 5Fh or less are used for Indexed Literal Offset Addressing. Representative examples of typical byte-oriented and bit-oriented instructions in the Indexed Literal Offset mode are provided on the following page to show how execution is affected. The operand conditions shown in the examples are applicable to all instructions of these types. DS30000575C-page 612 29.2.3.1 Extended Instruction Syntax with Standard PIC18 Commands When the extended instruction set is enabled, the file register argument ‘f’ in the standard byte-oriented and bit-oriented commands is replaced with the literal offset value ‘k’. As already noted, this occurs only when ‘f’ is less than or equal to 5Fh. When an offset value is used, it must be indicated by square brackets (“[ ]”). As with the extended instructions, the use of brackets indicates to the compiler that the value is to be interpreted as an index or an offset. Omitting the brackets, or using a value greater than 5Fh within the brackets, will generate an error in the MPASM™ Assembler. If the index argument is properly bracketed for Indexed Literal Offset Addressing, the Access RAM argument is never specified; it will automatically be assumed to be ‘0’. This is in contrast to standard operation (extended instruction set disabled), when ‘a’ is set on the basis of the target address. Declaring the Access RAM bit in this mode will also generate an error in the MPASM Assembler. The destination argument, ‘d’, functions as before. In the latest versions of the MPASM Assembler, language support for the extended instruction set must be explicitly invoked. This is done with either the command-line option, /y, or the PE directive in the source listing. 29.2.4 CONSIDERATIONS WHEN ENABLING THE EXTENDED INSTRUCTION SET It is important to note that the extensions to the instruction set may not be beneficial to all users. In particular, users who are not writing code that uses a software stack may not benefit from using the extensions to the instruction set. Additionally, the Indexed Literal Offset Addressing mode may create issues with legacy applications written to the PIC18 assembler. This is because instructions in the legacy code may attempt to address registers in the Access Bank below 5Fh. Since these addresses are interpreted as literal offsets to FSR2 when the instruction set extension is enabled, the application may read or write to the wrong data addresses. When porting an application to the PIC18FXXJ94, it is very important to consider the type of code. A large, reentrant application that is written in C and would benefit from efficient compilation will do well when using the instruction set extensions. Legacy applications that heavily use the Access Bank will most likely not benefit from using the extended instruction set.  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY ADD W to Indexed (Indexed Literal Offset mode) BSF Bit Set Indexed (Indexed Literal Offset mode) Syntax: ADDWF Syntax: BSF [k], b Operands: 0  k  95 d  [0,1] Operands: 0  f  95 0b7 Operation: (W) + ((FSR2) + k)  dest Operation: 1  ((FSR2) + k) Status Affected: N, OV, C, DC, Z Status Affected: None ADDWF Encoding: [k] {,d} 0010 Description: 01d0 kkkk kkkk The contents of W are added to the contents of the register indicated by FSR2, offset by the value ‘k’. If ‘d’ is ‘0’, the result is stored in W. If ‘d’ is ‘1’, the result is stored back in register ‘f’. Words: 1 Cycles: 1 Encoding: 1000 bbb0 kkkk kkkk Description: Bit ‘b’ of the register indicated by FSR2, offset by the value ‘k’, is set. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register ‘f’ Process Data Write to destination Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read ‘k’ Process Data Write to destination Example: ADDWF Before Instruction W OFST FSR2 Contents of 0A2Ch After Instruction W Contents of 0A2Ch [OFST] ,0 = = = 17h 2Ch 0A00h = 20h = 37h = 20h Example: BSF Before Instruction FLAG_OFST FSR2 Contents of 0A0Ah After Instruction Contents of 0A0Ah [FLAG_OFST], 7 = = 0Ah 0A00h = 55h = D5h SETF Set Indexed (Indexed Literal Offset mode) Syntax: SETF [k] Operands: 0  k  95 Operation: FFh  ((FSR2) + k) Status Affected: None Encoding: 0110 1000 kkkk kkkk Description: The contents of the register indicated by FSR2, offset by ‘k’, are set to FFh. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read ‘k’ Process Data Write register Example: SETF Before Instruction OFST FSR2 Contents of 0A2Ch After Instruction Contents of 0A2Ch  2012-2016 Microchip Technology Inc. [OFST] = = 2Ch 0A00h = 00h = FFh DS30000575C-page 613 PIC18F97J94 FAMILY 29.2.5 SPECIAL CONSIDERATIONS WITH MICROCHIP MPLAB® IDE TOOLS The latest versions of Microchip’s software tools have been designed to fully support the extended instruction set for the PIC18F97J94 Family. This includes the MPLAB C18 C Compiler, MPASM assembly language and MPLAB Integrated Development Environment (IDE). When selecting a target device for software development, MPLAB IDE will automatically set default Configuration bits for that device. The default setting for the XINST Configuration bit is ‘1’, enabling the extended instruction set and Indexed Literal Offset Addressing. For proper execution of applications developed to take advantage of the extended instruction set, XINST must be set during programming. To develop software for the extended instruction set, the user must enable support for the instructions and the Indexed Addressing mode in their language tool(s). Depending on the environment being used, this may be done in several ways: • A menu option or dialog box within the environment that allows the user to configure the language tool and its settings for the project • A command-line option • A directive in the source code These options vary between different compilers, assemblers and development environments. Users are encouraged to review the documentation accompanying their development systems for the appropriate information. DS30000575C-page 614  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY 30.0 ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings(†) Ambient temperature under bias.............................................................................................................-40°C to +100°C Storage temperature .............................................................................................................................. -65°C to +150°C Voltage on MCLR with respect to VSS.......................................................................................................... -0.3V to 5.5V Voltage on any digital only I/O pin with respect to VSS (except VDD)........................................................... -0.3V to 5.5V Voltage on any combined digital and analog pin with respect to VSS (except VDD and MCLR)...... -0.3V to (VDD + 0.3V) Voltage on VBAT with respect to VSS ......................................................................................................... -0.3V to 3.66V Voltage on VUSB3V3 with respect to VSS ........................................................................................ (VDD – 0.3V) to +4.0V Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to 3.66V Voltage on D+ or D- with respect to VSS – 0W source impedance (Note 2)............................ -0.5V to (VUSB3V3 + 0.5V) Source impedance  28W, VUSB3V3  3.0V) .............................................................................................. -1.0V to +4.6V Total power dissipation (Note 1) ..................................................................................................................................1W Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin ..............................................................................................................................250 mA Input clamp current, IIK (VI < 0 or VI > VDD) .......................................................................................................... ±20 mA Output clamp current, IOK (VO < 0 or VO > VDD) .................................................................................................. ±20 mA Maximum output current sunk by any I/O pins........................................................................................................25 mA Maximum output current sourced by any I/O pins...................................................................................................25 mA Maximum current sunk byall ports combined.......................................................................................................200 mA Maximum current sourced by all ports combined..................................................................................................200 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD –  IOH} +  {(VDD – VOH) x IOH} + (VOL x IOL) 2: The original “USB 2.0 Specification” indicated that USB devices should withstand 24-hour short circuits of D+ or D- to VBUS voltages. This requirement was later removed in an engineering change notice (ECN) supplement to the USB specifications, which supersedes the original specifications. PIC18FXXJ94 family devices will typically be able to survive this short circuit test, but it is recommended to adhere to the absolute maximum specified here to avoid damaging the device. † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.  2012-2016 Microchip Technology Inc. DS30000575C-page 615 PIC18F97J94 FAMILY VOLTAGE-FREQUENCY GRAPH, REGULATOR DISABLED (INDUSTRIAL)(1,2) FIGURE 30-1: 4V 3.75V 3.6V Voltage (VDD) 3.25V PIC18F97J94 Family 2V 4 MHz Note 1: 2: 3V 2.5V Frequency 64 MHz When the USB module is enabled, VUSB3V3 and VDD should be connected together and provided 3.0V-3.6V. When the USB module is not enabled, VUSB3V3 and VDD should still be connected together. VCAP (nominal on-chip regulator output voltage) = 1.8V. DS30000575C-page 616  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 30-1: DC CHARACTERISTICS: SUPPLY VOLTAGE PIC18FXXJ94 (INDUSTRIAL) Standard Operating Conditions: 2V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C PIC18FXXJ94 (Industrial) Param No. D001 Symbol VDD Characteristic Supply Voltage Min. Typ. Max. Units 2.0 — 3.6 V D001C AVDD Analog Supply Voltage VDD – 0.3 — VDD + 0.3 V D001D AVSS Analog Ground Potential VSS – 0.3 — VSS + 0.3 V D001E VUSB3V3 USB Supply Voltage 3 3.3 3.6 V D002 VDR RAM Data Retention Voltage(1) 1.2 — — V D003 VPOR VDD/VBAT Start Voltage to Ensure Internal Power-on Reset Signal — — 0.7 V D004 SVDD VDD/VBAT Rise Rate to Ensure Internal Power-on Reset Signal 0.05 — — D005 BVDD Brown-out Reset Voltage BORV = 1(2) BORV = 0 1.8 2.0 1.88 2.05 1.95 2.20 V V USB module enabled(3) See Section 5.2 “Power-on Reset (POR)” for details V/ms See Section 5.2 “Power-on Reset (POR)” for details D006 VVDDBOR 1.4V 2.0 V D007 VVBATBOR 1.4V 1.95 V D008 VDSBOR Note 1: 2: 3: Conditions 1.8 This is the limit to which VDD can be lowered in Sleep mode, or during a device Reset, without losing RAM data. The device will operate normally until Brown-out Reset occurs, even though VDD may be below VDDMIN. VUSB3V3 should be connected to VDD.  2012-2016 Microchip Technology Inc. DS30000575C-page 617 PIC18F97J94 FAMILY TABLE 30-2: DC CHARACTERISTICS: POWER-DOWN AND SUPPLY CURRENT PIC18FXXJ94 (INDUSTRIAL) PIC18FXXJ94 Family (Industrial) Param No. Typ.(1) Max. Units 3.7 7.0 µA -40°C 3.7 7.0 µA +25°C 5.0 9.0 µA +60°C DC60 DC61 DC70 Note 1: 2: 3: 4: Conditions 9.0 18 µA +85°C 3.7 8.0 µA -40°C 3.7 8.0 µA +25°C 5.0 11.0 µA +60°C 10 20 µA +85°C 0.07 0.55 µA -40°C 0.09 0.55 µA +25°C 2.0 3.2 µA +60°C 7.0 8.5 µA +85°C 0.10 0.65 µA -40°C 0.15 0.65 µA +25°C 2.0 3.5 µA +60°C 7.2 9.0 µA +85°C 0.06 0.5 µA -40°C 0.08 0.5 µA +25°C 0.21 0.8 µA +60°C 0.41 1.5 µA +85°C 0.09 0.6 µA -40°C 0.11 0.6 µA +25°C 0.42 1.2 µA +60°C 0.8 4.8 µA +85°C 0.4 3.0 µA -40°C TO +85°C 2.0V Sleep(2) 3.3V 2.0V Retention Sleep or Retention Deep Sleep(3) 3.3V 2.0V Deep Sleep 3.3V 0 RTCC with VBAT mode (LPRC or SOSC)(4) Data in the Typical column is at 3.3V, 25°C; typical parameters are for design guidance only and are not tested. Retention regulator is disabled; SRETEN (RCON4= 0), RETEN (CONFIG7L= 1). Retention regulator is enabled; SRETEN (RCON4 = 1), RETEN (CONFIG7L = 0). VBAT pin is connected to the battery and RTCC is running with VDD = 0. TABLE 30-3: Param No. Standard Operating Conditions: 2V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for industrial DC CHARACTERISTICS: POWER-DOWN AND SUPPLY CURRENT PIC18F97J94 FAMILY (INDUSTRIAL) Device Typ. Max. Units Conditions Supply Current (IDD) All Devices DS30000575C-page 618 22 55 µA -40°C to +85°C VDD = 2.0V 23 56 µA -40°C to +85°C VDD = 3.3V 21 54 µA -40°C to +85°C VDD = 2.0V 22 55 µA -40°C to +85°C VDD = 3.3V FOSC = 31 kHz, RC_RUN FOSC = 31 kHz, RC_IDLE  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 30-4: Param No. DC CHARACTERISTICS: POWER-DOWN AND SUPPLY CURRENT PIC18F97J94 FAMILY (INDUSTRIAL) Device Typ. Max. Units Conditions 22 55 µA -40°C to +85°C VDD = 2.0V 23 56 µA -40°C to +85°C VDD = 3.3V 21 54 µA -40°C to +85°C VDD =2.0V 22 55 µA -40°C to +85°C VDD = 3.3V Supply Current (IDD) All Devices TABLE 30-5: Param No. FOSC = 32 kHz, SEC_RUN FOSC = 32 kHz, SEC_IDLE DC CHARACTERISTICS: POWER-DOWN AND SUPPLY CURRENT PIC18F97J94 FAMILY (INDUSTRIAL) Device Typ. Max. Units Conditions 325 430 µA -40°C to +85°C VDD = 2.0V 325 430 µA -40°C to +85°C VDD = 3.3V 540 700 µA -40°C to +85°C VDD = 2.0V 540 700 µA -40°C to +85°C VDD = 3.3V 820 1000 µA -40°C to +85°C VDD = 2.0V 825 1000 µA -40°C to +85°C VDD = 3.3V 275 370 µA -40°C to +85°C VDD = 2.0V 275 370 µA -40°C to +85°C VDD = 3.3V Supply Current (IDD) All Devices 345 440 µA -40°C to +85°C VDD = 2.0V 345 440 µA -40°C to +85°C VDD = 3.3V 435 620 µA -40°C to +85°C VDD = 2.0V 435 620 µA -40°C to +85°C VDD = 3.3V  2012-2016 Microchip Technology Inc. FOSC = 1 MHz, RC_RUN FOSC = 4 MHz, RC_RUN FOSC = 8 MHz, RC_RUN FOSC = 1 MHz, RC_IDLE FOSC = 4 MHz, RC_IDLE FOSC = 8 MHz, RC_IDLE DS30000575C-page 619 PIC18F97J94 FAMILY TABLE 30-6: Param No. DC CHARACTERISTICS: POWER-DOWN AND SUPPLY CURRENT PIC18F97J94 FAMILY (INDUSTRIAL) Device Typ. Max. Units Conditions 100 150 µA -40°C to +85°C VDD = 2.0V 105 155 µA -40°C to +85°C VDD = 3.3V 330 390 µA -40°C to +85°C VDD = 2.0V 340 405 µA -40°C to +85°C VDD = 3.3V 5.0 5.5 mA -40°C to +85°C VDD = 2.0V 5.0 5.5 mA -40°C to +85°C VDD = 3.3V 5.7 6.5 mA -40°C to +85°C VDD = 2.0V 5.7 7.0 mA -40°C to +85°C VDD = 3.3V 52 90 µA -40°C to +85°C VDD = 2.0V Supply Current (IDD) All Devices DS30000575C-page 620 66 95 µA -40°C to +85°C VDD = 3.3V 135 185 µA -40°C to +85°C VDD = 2.0V 145 195 µA -40°C to +85°C VDD = 3.3V 1.8 2.6 mA -40°C to +85°C VDD = 2.0V = 3.3V 2.0 2.8 mA -40°C to +85°C VDD 2.3 2.9 mA -40°C to +85°C VDD = 2.0V 2.4 3.0 mA -40°C to +85°C VDD = 3.3V FOSC = 1 MHz, PRI_RUN mode, EC Oscillator FOSC = 4 MHz, PRI_RUN mode, EC Oscillator FOSC = 64 MHz, PRI_RUN mode, EC Oscillator FOSC = 64 MHz, PRI_RUN mode, 8 MHz EC Oscillator with 96 MHz or 8X PLL FOSC = 1 MHz, PRI_IDLE mode, EC Oscillator FOSC = 4 MHz, PRI_IDLE mode, EC Oscillator FOSC = 64 MHz, PRI_IDLE mode, EC Oscillator FOSC = 64 MHz, PRI_IDLE mode, 8 MHz EC Oscillator with 96 MHz or 8X PLL  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 30-7: Param No. DC CHARACTERISTICS: POWER-DOWN AND SUPPLY CURRENT PIC18F97J94 FAMILY (INDUSTRIAL) Device Typ.(1) Max. Units Conditions Module Differential Currents (∆IWDT, ∆IBOR, ∆IHLVD, ∆IDSBOR, ∆IDSWDT, ∆IOSCB, ∆IADRC, ∆ILCD, ∆IUSB) D020 (∆IWDT) D021 (∆IBOR) D022 (∆IHLVD) Watchdog Timer 0.4 1 µA -40°C to +85°C VDD = 2.0V 0.4 1 µA -40°C to +85°C VDD = 3.3V Brown-out Reset 8 µA -40°C to +85°C VDD = 2.0V 9 µA -40°C to +85°C VDD = 3.3V High-Power BOR 4 8 µA -40°C to +85°C VDD = 2.0V 5 9 µA -40°C to +85°C VDD = 3.3V D023 (∆IDSBOR) Deep Sleep BOR 135 480 nA -40°C to +85°C VDD = 2.0V to 3.3V ∆Deep Sleep BOR(2) D024 (∆IDSWDT) Deep Sleep Watchdog Timer 290 480 nA -40°C to +85°C VDD = 2.0V to 3.3V ∆Deep Sleep WDT(2) D025 (∆IOSCB) D027 (∆ILCD) D028 (∆IADRC) D028 (∆IUSB) Note 1: 2: 3: 4: 5: High/Low-Voltage Detect 4 5 Real-Time Clock/ Calendar with Timer1 Oscillator 0.38 1 µA -40°C to +85°C VDD = 2.0V 0.55 1 µA -40°C to +85°C VDD = 3.3V LCD Module 0.6 4 µA -40°C to +85°C VDD = 3.3V ∆LCD External/Internal, 1/8 MUX, 1/3 Bias(2,3) 6 30 µA -40°C to +85°C VDD = 2.0V 7 40 µA -40°C to +85°C VDD = 3.3V ∆LCD Charge Pump, 1/8 MUX, 1/3 Bias(2,4) A/D with RC 330 500 µA -40°C to +85°C VDD = 2.0V 385 500 µA -40°C to +85°C VDD = 3.3V 1 2 mA -40°C to +85°C VDD and VUSB3V3 = 3.3V USB Module DC CHARACTERISTICS: POWER-DOWN AND SUPPLY CURRENT PIC18F97J94 FAMILY (INDUSTRIAL) DC CHARACTERISTICS Sym. VBT Characteristic Operating Voltage VBTADC VBAT A/D Monitoring Voltage Specification(1) Note 1: USB enabled, no cable connected; traffic makes a large difference(5) Data in the Typical column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. Incremental current while the module is enabled and running. LCD is enabled and running, no glass is connected; the resistor ladder current is not included. LCD is enabled and running, no glass is connected. This is the module differential current when the USB module is enabled and clocked at 48 MHz, but with no USB cable attached. When the USB cable is attached, or data is being transmitted, the current consumption may be much higher (see Section 27.6.4 “USB Transceiver Current Consumption”). During USB Suspend mode (USBEN = 1, SUSPND = 1, bus in Idle state), the USB module current will be dominated by the D+ or D- pull-up resistor. The integrated pull-up resistors use “resistor switching” according to the resistor_ecn supplement to the “USB 2.0 Specification” and therefore, may be as low as 900Ω during Idle conditions. TABLE 30-8: Param No. Sleep mode 32.768 kHz, T1OSCEN = 1, LPT1OSC = 0 Standard Operating Conditions: 3.0V < VDD < 3.6V -40°C  TA  +85°C for Industrial (unless otherwise stated) Min. Typ. Max. Units Conditions 2.0 — 3.6 V Battery connected to VBAT pin 1.6 — 3.6 V A/D monitoring the VBAT pin using the internal A/D channel Measure A/D value using the A/D represented by the equation (Measured Voltage = ((VBAT/2)/VDD) * 1024) for 10-bit A/D; Measured Voltage = ((VBAT/2)/VDD) * 4096) for 12-bit A/D.  2012-2016 Microchip Technology Inc. DS30000575C-page 621 PIC18F97J94 FAMILY TABLE 30-9: DC CHARACTERISTICS: POWER-DOWN AND SUPPLY CURRENT PIC18F97J94 FAMILY (INDUSTRIAL) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C  TA  +85°C for industrial DC CHARACTERISTICS Param No. Sym. VIL D031 D031A D031B D032 D033 D033A D034 Characteristic Input Low Voltage All I/O Ports: Schmitt Trigger Buffer RC3 and RC4 MCLR OSC1 OSC1 SOSCI VIH D041 D041A D041B D042 D043 D043A D044 Input High Voltage All I/O Ports: Schmitt Trigger Buffer RC3 and RC4 MCLR OSC1 OSC1 SOSCI Min. Max. Units Conditions Vss Vss Vss Vss Vss Vss Vss 0.2 VDD 0.3 VDD 0.8 0.2 VDD 0.2 VDD 0.2 VDD 0.3 VDD V V V V V V V 2V  VDD 3.6V I2C enabled SMBus enabled 0.8 VDD 0.7 VDD 2.1 0.8 VDD 0.9 VDD 0.7 VDD 0.7 VDD VDD VDD VDD VDD VDD VDD VDD V V V V V V V 2V  VDD  3.6V I2C enabled SMBus enabled ±50 ±500 nA LP, MS, HS modes EC modes RC mode HS mode D060 Input Leakage Current(1) I/O Ports D061 D063 MCLR OSC1 — — ±500 1 nA µA Vss  VPIN VDD Pin at high-impedance Vss VPIN VDD Vss VPIN VDD IPU Weak Pull-up Current Weak Pull-up Current 50 400 µA VDD = 3.6V, VPIN = Vss VOL Output Low Voltage I/O Ports: All Ports OSC2/CLKO (EC modes) — — — — 0.4 0.4 0.4 0.4 V V V V IOL = 6.6 mA, VDD = 3.6V IOL = 5.0 mA, VDD = 2V IOL = 6.6 mA, VDD = 3.6V IOL = 5.0 mA, VDD = 2V 3.0 2.4 1.6 1.4 — — — — V V V V IOH = -3.0 mA, VDD = 3.6V IOH = -6.0 mA, VDD = 3.6V IOH = -1.0 mA, VDD = 2V IOH = -3.0 mA, VDD = 2V 2.4 1.4 — — V V IOH = -6.0 mA, VDD = 3.6V IOH = -1.0 mA, VDD = 2V — 20 pF — — 50 400 pF pF In HS mode when external clock is used to drive OSC1 To meet the AC Timing Specifications I2C Specification IIL D070 D080 D083 VOH D090 Output High Voltage(1) I/O Ports: All Ports OSC2/CLKO (INTOSC, EC modes) D092 D100 COSC2 Capacitive Loading Specs on Output Pins OSC2 Pin D101 D102 CIO CB All I/O Pins and OSC2 SCLx, SDAx Note 1: Negative current is defined as current sourced by the pin. DS30000575C-page 622  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 30-10: DC CHARACTERISTICS: CTMU CURRENT SOURCE SPECIFICATIONS Standard Operating Conditions: 2V to 3.6V Operating temperature -40°C  TA  +85°C for Industrial DC CHARACTERISTICS Param Sym. No. Note 1: Min. Typ.(1) Max. Units IOUT1 CTMU Current Source, Base Range — 550 — nA CTMUCON1 = 01 IOUT2 CTMU Current Source, 10x Range — 5.5 — A CTMUCON1 = 10 IOUT3 CTMU Current Source, 100x Range — 55 — A CTMUCON1 = 11 Characteristic Conditions Nominal value at center point of current trim range (CTMUCON1 = 000000). TABLE 30-11: MEMORY PROGRAMMING REQUIREMENTS Standard Operating Conditions Operating temperature -40°C  TA  +85°C for Industrial DC CHARACTERISTICS Param Sym. No. Characteristic Min. Typ† Max. Units Conditions Internal Program Memory Programming Specifications(1) D110 VPP Voltage on MCLR/VPP Pin D113 IDDP Supply Current During Programming D130 EP Cell Endurance D131 VPR VDD for Read VDD + 1.5 — 10 V — — 10 mA 1K 20K — E/W 2 — 3.6 V — 3.6 V (Note 2, Note 3) Program Flash Memory D132B VPEW Voltage for Self-Timed Erase or Write Operations VDD 2 D133A TIW Self-Timed Write Cycle Time — 2 — ms D133B TIE Self-Timed Block Erased Cycle Time — 33 — ms 10 — — Year mA D134 TRETD Characteristic Retention D135 IDDP Supply Current during Programming — — 10 D140 TWE Writes per Erase Cycle — — 1 -40C to +85C PIC18FXXKXX devices Provided no other specifications are violated For each physical address † Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: These specifications are for programming the on-chip program memory through the use of table write instructions. 2: Required only if single-supply programming is disabled. 3: The MPLAB® ICD 2 does not support variable VPP output. Circuitry to limit the MPLAB ICD 2 VPP voltage must be placed between the MPLAB ICD 2 and the target system when programming or debugging with the MPLAB ICD 2.  2012-2016 Microchip Technology Inc. DS30000575C-page 623 PIC18F97J94 FAMILY TABLE 30-12: COMPARATOR SPECIFICATIONS Operating Conditions: 2.0V  VDD  3.6V, -40°C  TA  +85°C Param No. D300 Sym. Characteristics Input Offset Voltage VIOFF Min. Typ. Max. Units — ±5.0 40 mV D301 VICM Input Common-Mode Voltage 0 — AVDD V D302 CMRR Common-Mode Rejection Ratio 55 — — dB D303 TRESP Response Time(1) — 150 400 ns D304 TMC2OV Comparator Mode Change to Output Valid* — — 10 s Note 1: Comments Response time is measured with one comparator input at (AVDD – 1.5)/2, while the other input transitions from VSS to VDD. TABLE 30-13: COMPARATOR VOLTAGE REFERENCE SPECIFICATIONS Operating Conditions: 2.0V  VDD  3.6V, -40°C  TA  +85°C Param No. Sym. Characteristics Min. Typ. Max. Units D310 VRES Resolution VDD/32 — VDD/32 LSb D311 VRAA Absolute Accuracy — — 3/4 LSb D312 VRUR Unit Resistor Value (R) — 2k —  TSET Time(1) — — 10 s D313 Note 1: Settling Comments Settling time measured while CVRR = 1 and CVR transitions from ‘0000’ to ‘1111’. TABLE 30-14: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS Operating Conditions: -40°C  TA  +85°C Param No. Sym. Characteristics Min. Typ. Max. Units VRGOUT Regulator Output Voltage — 1.8 — V CEFC 4.7 10 — F External Filter Capacitor Value Comments Capacitor must be low-ESR, a low series resistance (< 5) TABLE 30-15: RC OSCILLATOR START-UP TIME AC CHARACTERISTICS Param No. Characteristics Standard Operating Conditions: 2V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial Min. Typ. Max. Units TFRC — 15 — µs TLPRC — 10 — µs DS30000575C-page 624 Comments  2012-2016 Microchip Technology Inc. PIC18F97J94 FAMILY TABLE 30-16: USB MODULE SPECIFICATIONS Operating Conditions: -40°C