PL502-03SC

PL502-03 Low Phase Noise VCXO (48MHz to 100MHz) FEATURES       VCXO output for the 48MHz to 100MHz range Low phase noise (-130 dBc @ 10kHz offset at 48MHz) LVCMOS output 12 to 25MHz crystal input Integrated variable capacitors Selectable High Drive (30mA) or Standard Drive (10mA) output Wide pull range (± 250 ppm typ) Low period jitter: 3.5ps RMS 3.3V operation Available in 8-Pin SOP XOUT 1 N/C 2 VCON 3 GND 4 PL502-03     PIN CONFIGURATION 8 XIN 7 OE^ 6 VDD 5 CLK SOP-8L Note: ^ deno tes internal pull up DESCRIPTION The PL502-03 is a low cost, high performance and low phase noise VCXO for the 48 to 100MHz range, providing less than -130dBc at 10kHz offset at 48MHz. The very low jitter (3.5ps RMS period jitter) makes this chip ideal for applications requiring vol tage controlled frequency sources. Input crystal can range from 12 to 25MHz (fundamental resonant mode). OUTPUT RANGE MULTIPLIER FREQUENCY RANGE OUTPUT BUFFER X4 48 - 100MHz LVCMOS BLOCK DIAGRAM VCO Divider Reference Divider XIN XOUT XTAL OSC Phase Comparator Charge Pump Loop Filter VCO CLK OE VARICAP VCON Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 5/16/11 Page 1 PL502-03 Low Phase Noise VCXO (48MHz to 100MHz) PIN DESCRIPTIONS Name Number Type Description XOUT 1 I Crystal output. See Crystal Specifications on page 4. N/C 2 - Not connected. VCON 3 I Voltage Control input. GND 4 P Ground. CLK 5 O Output clock. VDD 6 P +3.3V power supply. OE 7 I Output enable input. Disables (tri -state) output when low. Internal pull-up enables output by default if pin is not connected to low. XIN 8 I Crystal input. See Crystal Specifications on page 4. ELECTRICAL SPECIFICATIONS 1. Absolute Maximum Ratings PARAMETERS Supply Voltage SYMBOL MIN. V DD MAX. UNITS 4.6 V Input Voltage, dc VI -0.5 V DD+0.5 V Output Voltage, dc VO -0.5 V DD+0.5 V Storage Temperature TS -65 150 C Ambient Operating Temperature* TA -40 85 C Junction Temperature TJ 125 C Lead Temperature (soldering, 10s) 260 C ESD Protection, Human Body Model 2 kV Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods m ay cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the dev ice at these or any other conditions above the operational limits noted in this specification is n ot implied. Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only. 2. AC Electrical Specifications PARAMETERS SYMBOL CONDITIONS Input Crystal Frequency MIN. TYP. 12 Output Clock Rise/Fall Time (Standard Drive) 0.3V ~ 3.0V, 15 pF load Output Clock Rise/Fall Time (High Drive) 0.3V ~ 3.0V, 15 pF load Output Clock Duty Cycle Measured @ 50% V DD MAX. UNITS 25 MHz 2.4 ns 1.2 45 50 55 % Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 5/16/11 Page 2 PL502-03 Low Phase Noise VCXO (48MHz to 100MHz) 3. DC Electrical Specifications PARAMETERS SYMBOL CONDITIONS MIN. F XIN = 25MHz Output load 10pF TYP. MAX. UNITS 16 20 mA 3.63 V Supply Current, Dynamic, with Loaded Outputs I DD Operating Voltage V DD Output Drive Current (High Drive) I OH V OH= V DD -0.4V, V DD =3.3V 30 mA I OL V OL = 0.4V, V DD = 3.3V 30 mA Output Drive Current (Standard Drive) I OH V OH= V DD -0.4V, V DD =3.3V 10 mA I OL V OL = 0.4V, V DD = 3.3V 10 mA 2.97 50 Short Circuit Current VCXO Control Voltage VCON 0 mA 3.3 V MAX. UNITS 10 ms 4. Voltage Control Crystal Oscillator PARAMETERS VCXO Stabilization Time * SYMBOL T VCXOSTB CONDITIONS MIN. TYP. From power valid VCXO Tuning Range F XIN = 12 – 25MHz; XTAL C0 /C1 < 250 0V  VCON  3.3V CLK output pullability VCON=1.65V, 1.65V 500 200 VCXO Tuning Characteristic ppm 150 Pull range linearity ppm/V 10 VCON pin input impedance VCON modulation BW ppm % 2000 kΩ 10 kHz 0V  VCON  3.3V, -3dB Note: Parameters denoted with an asterisk (*) represent nominal characterization data and are not production tested to any specific limits. 5. Jitter and Phase Noise specification PARAMETERS CONDITIONS MIN. TYP. MAX. UNITS RMS Period Jitter (1 sigma – 1000 samples) with capacitive decoupling between VDD and GND. 3.5 ps Phase Noise relative to carrier 48MHz @100Hz offset -100 dBc/Hz Phase Noise relative to carrier 48MHz @1kHz offset -123 dBc/Hz Phase Noise relative to carrier 48MHz @10kHz offset -130 dBc/Hz Phase Noise relative to carrier 48MHz @100kHz offset -125 dBc/Hz Phase Noise relative to carrier 48MHz @1MHz offset -125 dBc/Hz Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 5/16/11 Page 3 PL502-03 Low Phase Noise VCXO (48MHz to 100MHz) 6. Crystal Specifications PARAMETERS SYMBOL MIN. F XIN 12 Crystal Resonator Frequency Crystal Loading Capacitance Rating TYP. CL (x ta l) UNITS 25 MHz 9.5 pF C0/C1 ESR MAX. RS 250 - 30 Ω Note: Crystal Loading rating: 9.5pF is the loading the crystal sees from the VCXO chip at VCON = 1.65V. It is assumed that the crystal will be at no minal frequency at this load. If the crystal requires more load to be at nominal frequency, the additional load must be added externally. This however may reduce the pull range. PACKAGE INFORMATION (GREEN PACKAGE COM PLIANT) 8 PIN SOP (in mm) Symbol A A1 B C D E H L e Min. Max. 1.47 1.73 0.10 0.25 0.33 0.51 0.19 0.25 4.80 4.95 3.80 4.00 5.80 6.20 0.38 1.27 1.27 BSC E H D A A1 C e B L Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 5/16/11 Page 4 PL502-03 Low Phase Noise VCXO (48MHz to 100MHz) ORDERING INFORM ATION (GREEN PACKAGE COM PLIANT) For part ordering, please contact our Sales Department: 2180 Fortune Drive, San Jose, CA 95131, USA Tel: (408) 944-0800 Fax: (408) 474-1000 PART NUMBER The order number for this device is a combination of the following: Part number, Package type and Operating temperature range PL502-03 H X X X Part Number Shipping Option Blank=Tube R=Tape & Reel Optional High Drive Package Type S=SOP-8L Part/Order Number PL502-03SC PL502-03SC-R PL502-03HSC PL502-03HSC-R Temperature Range C=Commercial (0°C to 70°C) I=Industrial (-40°C to 85°C) Marking P502-03 SC LLLLL P502-03H SC LLLLL Package Option SOP - Tube SOP - Tape and Reel SOP - Tube SOP - Tape and Reel *Note: “LLL” or “LLLLL” are designates lot number Micrel Inc., reserves the right to make changes in its products or specifications, or both at any time without notice. The in formation furnished by Micrel is believed to be accurate and reliable. However, Micrel makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: Micrel’s products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Micrel Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 5/16/11 Page 5