PL602-38QC-R

PL602-35/-37/-38/-39 750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s FEATURES 1 XIN 2 XOUT 3 SEL3^ 4 SEL2^ 5 OE 6 GND 7 GND 8 1 6 1 5 1 4 1 3 1 2 1 1 1 0 SEL0^ SEL1^ GND CLKC VDD CLKT GND 9 GND VDD / GND* SEL0^ / VDD* SEL1^ TSSOP-16L 12 11 10 9 DESCRIPTION SEL3^ 14 SEL2^ 15 OE 16 PL602-3x 1 BLOCK DIAGRAM 2 3 4 GND 13 GND XOUT GND The PL602-35 (LVPECL with inverted OE), PL602-37 (LVCMOS), PL602-38 (LVPECL), and PL602-39 (LVDS) are high performance and low phase noise XO IC chips. They provide phase noise performance as low as –127dBc at 10kHz offset (at 155MHz), by multiplying the input crystal frequency up to 32x. The very low jitter makes them ideal for a wide range of applications, including SONET/SDH and FEC. They accept fundamental parallel resonant mode crystals from 12MHz to 25MHz. GND       VDD PL602-3x  Selectable 750kHz to 800MHz range. Low phase noise output  -127dBc/Hz for 155.52MHz @ 10kHz offset  -115dBc/Hz for 622.08MHz @ 10kHz offset LVCMOS (PL602-37), LVPECL (PL602-35 and PL602-38) or LVDS (PL602-39) output. 12MHz to 25MHz crystal input. No external crystal load capacitors required. Output Enable selector. Selectable /16 to x32 frequency divider/multiplier. 3.3V operation. Available in 16-Pin TSSOP or 16-pin 3x3mm QFN GREEN/RoHS compliant packages. XIN   PIN CONFIGURATION (Top View) 8 GND 7 CLKC 6 VDD 5 CLKT QFN-16L SEL[3:0] ^: *: OE XIN XOUT Oscillator Amplifier w/ integrated load cap. PLL (Phase Locked Loop) CLKC CLKT Internal pull -up On QFN package, PL 602-35/-38 do not have SEL0 available: Pin 10 is VDD, pin 11 is GND. However, PL602-37/-39 have SEL0 (pin 10), and pin11 is VDD. See pin assignment table for d etails. Note: On QFN package there is a large center pad for thermal relief. This pad needs to be connected to GND. OUTPUT ENABLE LOGICAL LEVELS Part # PL602-38 PLL by-pass PL602-3x PL602-35 PL602-37 PL602-39 OE 0 (Default) State Output enabled 1 Tri-state 0 Tri-state 1 (Default) Output enabled OE input: Logical states defined by LVPECL levels for PL602-38 Logical states defined by LVCMOS levels for PL602-37/-39 Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 03/07/2012 Page 1 PL602-35/-37/-38/-39 750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s FREQUENCY SELECTION TABLE SEL3 SEL2 SEL1 SEL0 Selected Multiplier 0 0 1 1 Fin x 32 0 1 1 0 Fin / 8 0 1 1 1 Fin x 2 1 0 0 1 Fin / 2 1 0 1 0 Fin / 16 1 0 1 1 Fin x 4 1 1 0 0 Fin / 4 1 1 0 1 Fin x 8 1 1 1 0 Fin x 16 1 1 1 1 No multiplication Note: SEL0 is not available (always “1”) for PL602-35 and PL602-38 in 3x3mm package PIN DESCRIPTIONS PL602-35 and PL602-38 (see next page for PL602-37/-39) TSSOP Pin number 3x3mm QFN Pin number Type XIN 2 12 I Crystal input (See Crystal Specification on page 4) XOUT 3 13 I Crystal output (See Crystal Specification on page 4 ) OE 6 16 I Output enable pin (See OE logic state table on page 1) GND 7,8,9,10,14 1,2,3,4,8,11 P Ground connection CLKT 11 5 O LVPECL True output CLKC 13 7 O LVPECL Complementary output SEL0 16 Not available I SEL1 15 9 I SEL2 5 15 I SEL3 4 14 I VDD 1, 12 6,10 P Name Description Multiplier selector pins. These pins have an internal pullup that will default SEL to ‘1’ when not connected to GND. +3.3V power supply. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 03/07/2012 Page 2 PL602-35/-37/-38/-39 750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s PIN DESCRIPTIONS PL602-37/-39 (see previous page for PL602-35/-38) Name TSSOP Pin number 3x3mm QFN Pin number Type XIN 2 12 I Crystal input. See Crystal Specification on page 4. XOUT 3 13 I Crystal output. See Crystal Specification on page 4. OE 6 16 I Output enable pin (see OE logic state table on page 1). GND 7,8,9,10,14 1,2,3,4,8 P Ground. CLKT 11 5 O LVDS True output for PL602-39. No Connect for PL602-37 CLKC 13 7 O LVDS Complementary output for PL602-39 LVCMOS out for PL602-37 SEL0 16 10 I SEL1 15 9 I SEL2 5 15 I SEL3 4 14 I VDD 1, 12 6,11 P Description Multiplier selector pins. These pins have an internal pull-up that will default SELx to ‘1’ when not connected to GND. +3.3V power supply. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 03/07/2012 Page 3 PL602-35/-37/-38/-39 750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s ELECTRICAL SPECIFICATIONS 1. Absolute Maximum Ratings PARAMETERS SYMBOL Supply Voltage MIN. V DD MAX. UNITS 4.6 V Input Voltage, dc VI -0.5 V DD+0.5 V Output Voltage, dc VO -0.5 V DD+0.5 V Storage Temperature TS -65 150 C Ambient Operating Temperature* TA -40 85 C Junction Temperature TJ 125 C 260 C Lead Temperature (soldering, 10s) ESD Protection, Human Body Model 2.5 kV Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. * Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only. 2. Crystal Specifications PARAMETERS SYMBOL CONDITIONS MIN. Crystal Resonator Frequency F XIN Parallel Fundamental Mode 12 Crystal Loading Rating CL (x ta l) Recommended ESR RE TYP. MAX. UNITS 25 MHz 20 AT cut pF 30 Ω MAX. UNITS 3. General Electrical Specifications PARAMETERS SYMBOL CONDITIONS Supply Current, Dynamic (with Loaded Outputs) I DD F OUT