SST12LN01-QU6F

SST12LN01 2.4-2.5 GHz WLAN Low-Noise Amplifier Features 1.0 • Gain: SST12LN01 is a cost effective Low-Noise Amplifier (LNA) which requires no external RF-matching components. This device is based on the GaAs pHEMT technology, and complies with 802.11 b/g applications. – Typically 13.5 dB gain across 2.4–2.5 GHz • Noise Figure: – Typically 1.5 dB across 2.4–2.5 GHz • P1dB: – Typically -5dBm with VDD 3.3V • Low-Current Consumption – 10 mA across 2.4–2.5 GHz • 50 Input/Output Matched • Packages available – 6-contact UQFN – 3 mm x 1.6 mm • All non-Pb (lead-free) devices are RoHS compliant Applications • WLAN • Bluetooth • Wireless Network  2015 Microchip Technology Inc. PRODUCT DESCRIPTION SST12LN01 provides high-performance, low-noise, and moderate-gain operation within the 2.4–2.5 GHz frequency band. Across this frequency band, the LNA typically provides 13.5 dB gain and 1.5 dB noise figure. This LNA cell is designed with a self DC-biasing scheme, which maintains low DC current consumption, nominally at 10 mA, during operation. Optimum performance is achieved with only a single power supply, and no external bias resistors or networks are required. The input and output ports are single-ended 50 matched. RF ports are also DC isolated requiring no DC blocking capacitors or matching components. SST12LN01 is offered in a 6-contact UQFN package. See Figure 3-1 for pin assignments and Table 4-1 for pin descriptions. DS70005150A-page 1 SST12LN01 2.0 FUNCTIONAL BLOCKS FIGURE 2-1: 3.0 FUNCTIONAL BLOCK DIAGRAM PIN ASSIGNMENTS FIGURE 3-1: PIN ASSIGNMENTS FOR 16-CONTACT UQFN Top View (contacts facing down) VDD NC 1 RFIN 2 6 RF and DC GND 0 3 5 RFOUT 4 NC NC 1329 6-uqfn P1.0 4.0 PIN DESCRIPTIONS TABLE 4-1: Symbol PIN DESCRIPTION Pin No. Pin Name Type1 Function GND 0 Ground NC 1 No Connection RFIN 2 NC 3 No Connection Unconnected pin NC 4 No Connection Unconnected pin RFOUT 5 VDD 6 Unconnected pin I O Power Supply 2.4G RF input 2.4G RF output PWR 1. I=Input, O=Output DS70005150A-page 2  2015 Microchip Technology Inc. SST12LN01 5.0 ELECTRICAL SPECIFICATIONS The AC and DC specifications for the power amplifier interface signals. Refer to Table 5-2 for the DC voltage and current specifications. Refer to Figure 6-1 for the RF performance. Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device reliability.) Input power to pin 2 (PIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 dBm Average output power (POUT)1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 dBm Supply Voltage at pin 6 (VDD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +4.6V DC supply current (IDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 mA Operating Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40ºC to +85ºC Storage Temperature (TSTG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40ºC to +120ºC Maximum Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150ºC Surface Mount Solder Reflow Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C for 10 seconds 1. Never measure with CW source. Pulsed single-tone source with