SY100EL35ZG-TR

NOT RECOMMENDED FOR NEW DESIGNS Micrel, Inc. JK FLIP-FLOP FEATURES ■ ■ ■ ■ ■ SY10EL35 SY100EL35 SY10EL35 SY100EL35 DESCRIPTION 525ps propagation delay 2.2GHz toggle frequency High bandwidth output transistions Internal 75KΩ input pull-down resistors Available in 8-pin SOIC package The SY10/100EL35 are high-speed JK Flip-Flops. The J/K data enters the master portion of the flip-flop when the clock is LOW and is transferred to the slave and, thus, the outputs, upon a positive transition of the clock. The reset pin is asynchronous and is activated with a logic HIGH. TRUTH TABLE(1) J K R CLK Qn+1 L L L Z Qn L H L Z L H L L Z H H H L Z Qn X X H X L NOTE: 1. Z = LOW-to-HIGH transition. M9999-121205 hbwhelp@micrel.com or (408) 955-1690 Rev.: G 1 1 Amendment: /0 Issue Date: December 2005 SY10EL35 SY100EL35 Micrel, Inc. PACKAGE/ORDERING INFORMATION Ordering Information(1) J 1 J 8 VCC K 2 K 7 Q CLK SY10EL35LZC 3 6 Q 5 VEE R R Part Number 4 8-PIN SOIC (Z8-1) Package Type Operating Range Package Marking Lead Finish Z8-1 Commercial HEL35 Sn-Pb SY10EL35LZCTR(2) Z8-1 Commercial HEL35 Sn-Pb SY100EL35LZC Z8-1 Commercial XEL35 Sn-Pb SY100EL35LZCTR(2) Z8-1 Commercial XEL35 Sn-Pb SY10EL35LZI Z8-1 Industrial HEL35 Sn-Pb SY10EL35LZITR(2) Z8-1 Industrial HEL35 Sn-Pb SY100EL35LZI Z8-1 Industrial XEL35 Sn-Pb SY100EL35LZITR(2) Z8-1 Industrial XEL35 Sn-Pb SY10EL35LZG(3) Z8-1 Industrial HEL35 with Pb-Free bar-line indicator Pb-Free NiPdAu SY10EL35LZGTR(2, 3) Z8-1 Industrial HEL35 with Pb-Free bar-line indicator Pb-Free NiPdAu SY100EL35LZG(3) Z8-1 Industrial XEL35 with Pb-Free bar-line indicator Pb-Free NiPdAu SY100EL35LZGTR(2, 3) Z8-1 Industrial XEL35 with Pb-Free bar-line indicator Pb-Free NiPdAu Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-121205 hbwhelp@micrel.com or (408) 955-1690 2 SY10EL35 SY100EL35 Micrel, Inc. DC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = GND TA = –40°C Symbol IEE VEE IIH TA = 0°C TA = +25°C TA = +85°C Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Power Supply Current 10EL 100EL — — 27 27 32 32 — — 27 27 32 32 — — 27 27 32 32 — — 27 32 32 37 Power Supply Voltage 10EL 100EL — — –5.2 –4.5 — — –4.75 –4.20 –5.2 –4.5 –5.5 –5.5 –4.75 –4.20 –5.2 –4.5 –5.5 –5.5 –4.75 –4.20 –5.2 –4.5 –5.5 –5.5 Input HIGH Current — — 150 — — 150 — — 150 — — 150 Unit mA V µA AC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = GND TA = –40°C Symbol Parameter TA = 0°C TA = +25°C TA = +85°C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit fMAX Maximum Toggle Frequency 1.4 2.0 — 1.8 2.2 — 1.8 2.2 — 1.8 2.2 — GHz tPD Propagation Delay CLK to Output MR 290 225 515 450 — — 340 275 515 450 690 625 350 275 525 450 700 625 395 350 570 525 745 700 ps tS Set-up Time 150 0 — 150 0 — 150 0 — 150 0 — ps tH Hold Time 250 100 — 250 100 — 250 100 — 250 100 — ps tRR Reset Recovery 400 200 — 400 200 — 400 200 — 400 200 — ps tPW Minimum Pulse Width CLK, Reset 400 — — 400 — — 400 — — 400 — — ps tr tf Output Rise/Fall Times Q (20% to 80%) 100 225 350 100 225 350 100 225 350 100 225 350 ps M9999-121205 hbwhelp@micrel.com or (408) 955-1690 3 SY10EL35 SY100EL35 Micrel, Inc. 8-PIN SOIC .150" WIDE (Z8-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2005 Micrel, Incorporated. M9999-121205 hbwhelp@micrel.com or (408) 955-1690 4