SY100EPT23LKG-TR

SY100EPT21L 3.3V Differential ECL LVPECL-to-LVTTL Translator ECL Pro™ General Description The SY100EPT21L is a single, differential LVPECL-toLVTTL translator using a single +3.3V power supply. Because the device uses low-voltage positive ECL (LVPECL) levels, only +3.3V and ground are required. The small-outline 8-pin SOIC package and low-skew, singlegate design make the EPT21L ideal for applications that require the translation of a clock or data signal where minimal space, low power, and low cost are critical. VBB allows a differential, single-ended, or AC-coupled interface to the device. If used, the VBB output should be bypassed to VCC with 0.01µF capacitor. Under open input conditions, the /D is biased at a VCC/2 voltage level and the D input is pulled to ground. This condition forces the Q output low to provide added stability. The 100EPT is compatible with positive ECL 100K logic levels. For applications that require the smallest footprint, consider the SY89321L in ultra-small 8-pin MSOP and SOIC packages. Data sheets and support documentation can be found on Micrel’s web site at: www.micrel.com. ECL Pro™ Features • Guaranteed over the industrial temperature range: –40°C to +85°C • Pin-for-pin, plug-in replacement to MC100EPT21D/DT • 3.3V power supply • 1.9ns typical propagation delay • 275MHz fMAX (clock) • Differential LVPECL inputs • 24mA LVTTL output • Flow-through pin configuration • Q output defaults LOW with inputs open • VBB output • Available in 8-pin MSOP and SOIC packages Applications • ASIC/FPGA interface • Legacy interface • Precision differential-to-general purpose, single-ended translation Cross Reference Micrel ON Semiconductor SY100EPT21LZI MC100EPT21D SY100EPT21LZITR MC100EPT21DR2 SY100EPT21LKI MC100EPT21DT SY100EPT21LKITR MC100EPT21DTR2 ECL Pro is a trademark of Micrel, Inc Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com November 2012 M9999-112712-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY100EPT21L Ordering Information(1) Part Number Package Operating Range Marking SY100EPT21LZG(2) 8-Pin SOIC (Z8-1) Industrial XEP21L with Pb-Free bar-line indicator SY100EPT21LZGTR(2, 3) 8-Pin SOIC (Z8-1) Industrial XEP21L with Pb-Free bar-line indicator SY100EPT21LKG(2) 8-Pin MSOP (K8-1) Industrial XP21 with Pb-Free bar-line indicator SY100EPT21LKGTR(2, 3) 8-Pin MSOP (K8-1) Industrial XP21 with Pb-Free bar-line indicator Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Pb-Free packages are recommended for new designs. 3. Tape and Reel. Pin Configuration 8-Pin SOIC (Z8-1) 8-Pin MSOP (K8-1) Pin Description Pin Number Pin Name Pin Function 1 NC 2, 3 D, /D Differential LVPECL Input Pair 4 VBB Output Reference Voltage 5 GND Ground 6 NC No Connect No Connect 7 Q LVTTL Output 8 VCC Positive Supply Truth Table D /D Q L H L H L H Open Open L November 20012 2 M9999-112712-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY100EPT21L Absolute Maximum Ratings(1) Operating Ratings(2) Power Supply Voltage (VCC)......................... –0.5V to +3.8V PECL Input Voltage (VIN) .......................... 0V to VCC + 0.5V Voltage Applied to Output at HIGH State (VOUT) –0.5 to VCC Current Applied to Output at LOW State (IOUT) ............................................... Twice the Rated IOL (mA) Lead Temperature (soldering, 20sec.) ..................... +260°C Storage Temperature (Ts) ......................... –65°C to +150°C Power Supply Voltage (VCC) ........................ –0.5V to +3.8V Ambient Temperature (TA) .......................... –40°C to +85°C Package Thermal Resistance SOIC (θJA) ........................................................ 113°C/W MSOP (θJA) ...................................................... 124°C/W LVTTL Output DC Electrical Characteristics VCC = +3.3V, GND = 0V; TA = –40°C to +85°C; unless noted. Symbol Parameter Condition Min. IOS Output Short Circuit Current VOUT = 0V –80 ICC Power Supply Current VOH Output High Voltage IOH = –3.0mA(3) 2.3 VOL Output Low Voltage IOL = 24mA Typ. 14 Max. Units –275 mA 20 mA V 0.5 V Max. Units 150 µA LVTTL Input DC Electrical Characteristics VCC = +3.3V, GND = 0V; TA = –40°C to +85°C; unless noted. Symbol Parameter Condition Min. IIH Input HIGH Current IIL Input LOW Current VIH Input HIGH Voltage Note 3 2135 2420 mV VIL Input LOW Voltage Note 3 1490 1825 mV VBB Reference Output Note 3 1920 2040 mV D Typ. 0.5 /D µA –300 µA 1980 Notes: 1. Permanent device damage may occur if ratings in the absolute maximum ratings section are exceeded. This is a stress rating only and functional operation is not implied for conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. These values are for VCC = 3.3V. Level Specifications will vary 1:1 VCC. November 20012 3 M9999-112712-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY100EPT21L AC Electrical Characteristics VCC = +3.0V to +3.6V, GND = 0V; TA = –40°C to +85°C; unless noted. Symbol Parameter Condition Min. Typ. Max. Units tPD Propagation Delay CL = 20pF 1.5 1.9 2.5 ns CL = 20pF(1, 2) tskpp Part-to-Part Skew fMAX Maximum Input Frequency 275 VCMR Common Mode Range 1.2 VPP Minimum Peak-to-Peak Input Note 4 100 tr , tf Output Rise/Fall Time (1.0V to 2.0V) CL = 20pF 0.5 0.5 ns MHz VCC V mV 1.0 ns Notes: 1. Part-to-part skew considering HIGH-to-HIGH transitions at common VCC level. 2. These parameters are guaranteed but not tested. 3. The fMAX value is specified as the minimum guaranteed maximum frequency. Actual operational maximum frequency may be greater. 4. 100mV input guarantees full logic at output. November 20012 4 M9999-112712-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY100EPT21L Package Information(1) 8-Pin Plastic SOIC (Z8-1) Note: 1. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. November 20012 5 M9999-112712-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY100EPT21L Package Information (Continued) 8-Pin MSOP (K8-1) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2005 Micrel, Incorporated. November 20012 6 M9999-112712-F hbwhelp@micrel.com or (408) 955-1690