SY100H841ZC

NOT RECOMMENDED FOR NEW DESIGNS Precision Edge® SY10H841 ® Precision SY100H841 Edge SINGLE SUPPLY QUAD PECL-TO-TTL W/LATCHED OUTPUT ENABLE Micrel, Inc. SY10H841 SY100H841 FEATURES ■ ■ ■ ■ Translates positive ECL to TTL (PECL-to-TTL) 300ps pin-to-pin skew 500ps part-to-part skew Differential internal design for increased noise immunity and stable threshold inputs ■ VBB reference output Precision Edge® DESCRIPTION The SY10/100H841 are single supply, low skew translating 1:4 clock drivers. The devices feature a 24mA TTL output stage, with AC performance specified into a 50pF load capacitance. A latch is provided on-chip. When LEN is LOW (or left open, in which case it is pulled low by the internal pulldowns) the latch is transparent. A HIGH on the enable pin (EN) forces all outputs LOW. As frequencies increase to 40MHz and above, precise timing and shaping of clock signals becomes extremely important. The H841 solves several clock distribution problems such as minimizing skew (300ps), maximizing clock fanout (24mA drive), and precise duty cycle control through a proprietary differential internal design. The 10K version is compatible with 10KH ECL logic levels. The 100K version is compatible with 100K levels. ■ ■ ■ ■ Single supply Enable input Latch enable input Extra TTL and ECL power/ground pins to reduce cross-talk/noise ■ High drive capability: 24mA each output ■ Fully compatible with industry standard 10K, 100K I/O levels ■ Available in 16-pin SOIC package BLOCK DIAGRAM Q0 PIN NAMES Pin Q1 Q2 VBB D D D Q Q3 LEN Function GT TTL Ground (0V) VT TTL VCC (+5.0V) VE ECL VCC (+5.0V) GE ECL Ground (0V) D, D Signal Input (PECL) VBB VBB Reference Output (PECL) Q0 - Q3 Signal Outputs (TTL) EN Enable Input (PECL) LEN Latch Enable Input EN Precision Edge is a registered trademark of Micrel, Inc. M9999-032906 hbwhelp@micrel.com or (408) 955-1690 Rev.: G 1 Amendment: /0 Issue Date: March 2006 Precision Edge® SY10H841 SY100H841 Micrel, Inc. PACKAGE/ORDERING INFORMATION Ordering Information(1) LEN 1 16 Q3 Part Number Package Type Operating Range Package Marking Lead Finish EN 2 15 GT SY10H841ZC Z16-1 Commercial SY10H841ZC Sn-Pb GE 3 14 Q2 VE 4 D 5 D 6 11 Q1 VBB 7 10 GT GT 8 9 Q0 SOIC Z16-1 13 VT 12 VT 16-Pin SOIC (Z16-1) SY10H841ZCTR(2) Z16-1 Commercial SY10H841ZC Sn-Pb SY100H841ZC Z16-1 Commercial SY100H841ZC Sn-Pb SY100H841ZCTR(2) Z16-1 Commercial SY100H841ZC Sn-Pb SY10H841ZH(3) Z16-1 Commercial SY10H841ZH with Pb-Free bar-line indicator NiPdAu Pb-Free SY10H841ZHTR(2, 3) Z16-1 Commercial SY10H841ZH with Pb-Free bar-line indicator NiPdAu Pb-Free SY100H841ZH(3) Z16-1 Commercial SY100H841ZH with Pb-Free bar-line indicator NiPdAu Pb-Free SY100H841ZHTR(2, 3) Z16-1 Commercial SY100H841ZH with Pb-Free bar-line indicator NiPdAu Pb-Free Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-032906 hbwhelp@micrel.com or (408) 955-1690 2 Precision Edge® SY10H841 SY100H841 Micrel, Inc. PIN DESCRIPTION TRUTH TABLE D LEN EN Q Pin Symbol L L L L 1 LEN Latch Enable Input H L L H 2 EN Enable Input (PECL) X X H L 3 GE ECL Ground (0V) X H L Latch 4 VE ECL VCC (+5.0V) 5 D ECL Signal Input (Non-inverting) 6 D ECL Signal Input (Inverting) 7 VBB VBB Reference Output (PECL) 8 GT TTL Ground (0V) 9 Q0 Signal Output (TTL) 10 GT TTL Ground (0V) 11 Q1 Signal Output (TTL) 12 VT TTL VCC (+5.0V) 13 VT TTL VCC (+5.0V) 14 Q2 Signal Output (TTL) 15 GT TTL Ground (0V) 16 Q3 Signal Output (TTL) ABSOLUTE MAXIMUM RATINGS(1) Symbol Rating Value Unit VE (ECL) VT (TTL) Power Supply Voltage –0.5 to +7.0 –0.5 to +7.0 V VI (ECL) VOUT (TTL) Input Voltage 0.0 to VEE 0.0 to VT V TLEAD Lead Temperature Range (soldering, 20sec) Tstore Storage Temperature TA Operating Temperature +260 ˚C –65 to +150 ˚C 0 to +85 ˚C NOTE: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability. Description VCC AND CLOAD Ranges to meet duty cycle requirement: 0°C ≤ TA ≤ 85°C. Output duty cycle measured relative to 1.5V. Symbol Parameter Min. Typ. Max. Unit Condition PW Ranges of VCC and CL to meet min. pulse width (HIGH or LOW) at fOUT ≤ 40MHz VCC CL PW 4.75 10 11 5.0 — — 5.25 50 — V pF ns All Outputs PW Ranges of VCC and CL to meet min. pulse width (HIGH or LOW) at fOUT ≤ 50MHz VCC CL PW 4.875 15 9.0 5.0 — — 5.125 27 — V pF ns All Outputs DC CHARACTERISTICS VT = VE = 5.0V ± 5% TA = 0°C Symbol Parameter IEE Power Supply Current ECL ICCH Power Supply Current TTL ICCL M9999-032906 hbwhelp@micrel.com or (408) 955-1690 TA = +25°C TA = +85°C Min. Max. Min. Max. Min. Max. Unit — 40 — 40 — 40 mA VE Pin — 20 — 20 — 20 mA Total all VT pins — 25 — 25 — 25 3 Condition Precision Edge® SY10H841 SY100H841 Micrel, Inc. TTL DC ELECTRICAL CHARACTERISTICS VT = VE = +5.0V ± 5% TA = 0°C Symbol Parameter TA = +25°C TA = +85°C Min. Max. Min. Max. Min. Max. Unit Condition VOH Output HIGH Voltage 2.5 2.0 — — 2.5 2.0 — — 2.5 2.0 — — V IOH = –3.0mA IOH = –15mA VOL Output LOW Voltage — 0.5 — 0.5 — 0.5 V IOL = 24mA IOS Output Short Circuit Current –80 –200 –80 –200 –80 –200 mA VOUT = 0V 10H ECL DC ELECTRICAL CHARACTERISTICS(1) VT = VE = +5.0V ± 5% TA = 0°C Symbol Parameter TA = +25°C TA = +85°C Min. Max. Min. Max. Min. Max. Unit Condition IIH Input HIGH Current — 225 — 175 — 175 µA — IIL Input LOW Current 0.5 — 0.5 — 0.5 — µA — VIH Input HIGH Voltage 3.830 4.160 3.870 4.190 3.940 4.280 V VE = 5.0V VIL Input LOW Voltage 3.050 3.520 3.050 3.520 3.050 3.555 V VE = 5.0V VBB Output Reference Voltage 3.620 3.730 3.650 3.750 3.690 3.810 V VE = 5.0V Note: 1. ECL VIH, VIL and VBB are referenced to VCCE and will vary 1:1 with the power supply. The levels shown are for IVT = IVO = VCCE = +5.0V. 100H ECL DC ELECTRICALCHARACTERISTICS(1) VT = VE = +5.0V ± 5% TA = 0°C Symbol Parameter TA = +25°C TA = +85°C Min. Max. Min. Max. Min. Max. Unit Condition IIH Input HIGH Current — 225 — 175 — 175 µA — IIL Input LOW Current 0.5 — 0.5 — 0.5 — µA — VIH Input HIGH Voltage 3.835 4.120 3.835 4.120 3.835 4.120 V VE = 5.0V VIL Input LOW Voltage 3.190 3.525 3.190 3.525 3.190 3.525 V VE = 5.0V VBB Output Reference Voltage 3.620 3.740 3.620 3.740 3.620 3.740 V VE = 5.0V Note: 1. ECL VIH, VIL and VBB are referenced to VCCE and will vary 1:1 with the power supply. The levels shown are for IVT = IVO = VCCE = +5.0V. M9999-032906 hbwhelp@micrel.com or (408) 955-1690 4 Precision Edge® SY10H841 SY100H841 Micrel, Inc. AC CHARACTERISTICS VT = VE = 5.0V ± 5% TA = 0°C Symbol Parameter TA = +25°C TA = +85°C Min. Max. Min. Max. Min. Max. Unit Condition tPLH tPHL Propagation Delay D to Output Q0–Q3 2.7 3.7 2.7 3.7 2.7 3.7 ns CL = 50pF tskpp Part-to-Part Skew(1,4) Q0–Q3 — 0.5 — 0.5 — 0.5 ns CL = 50pF tskew++ Within-Device Skew(2,4) Q0–Q3 — 0.3 — 0.3 — 0.3 ns CL = 50pF tskew– – Within-Device Skew(3,4) Q0–Q3 — 0.3 — 0.3 — 0.3 ns CL = 50pF tPLH tPHL Propagation Delay LEN to Q Q0–Q3 2.7 3.7 2.7 3.7 2.7 3.7 ns CL = 50pF tPLH tPHL Propagation Delay EN to Output Q0–Q3 2.7 3.7 2.7 3.7 2.7 3.7 ns CL = 50pF tr tf Output Rise/Fall Time 1.0V to 2.0V Q0–Q3 — 1.5 — 1.5 — 1.5 ns CL = 50pF fMAX Max. Input Frequency(5,6) Q0–Q3 160 — 160 — 160 — MHz CL = 50pF — Pulse Width Q0–Q3 1.5 — 1.5 — 1.5 — ns — — Recovery Time EN Q0–Q3 1.0 — 1.0 — 1.0 — ns — tS Set-up Time D, EN Q0–Q3 0.75 — 0.75 — 0.75 — ns — tH Hold Time D, EN Q0–Q3 0.75 — 0.75 — 0.75 — ns — Notes: 1. Device-to-Device Skew considering HIGH-to-HIGH transitions at common VCC level. 2. Within-Device Skew considering HIGH-to-HIGH transitions at common VCC level. 3. Within-Device Skew considering LOW-to-LOW transitions at common VCC level. 4. All skew parameters are guaranteed but not tested. 5. Frequency at which output levels will meet at 0.8V to 2.0V minimum swing. 6. The fMAX value is specified as the minimum guaranteed maximum frequency. Actual operational maximum frequency may be greater. M9999-032906 hbwhelp@micrel.com or (408) 955-1690 5 Precision Edge® SY10H841 SY100H841 Micrel, Inc. TTL SWITCHING CIRCUIT VCC & VCCO VEE USE 0.1µF CAPACITORS FOR DECOUPLING. TTL PECL 50Ω COAX DEVICE UNDER TEST IN PULSE GENERATOR 50Ω COAX USE OSCILLOSCOPE INTERNAL 50Ω LOAD FOR TERMINATION. OUT 450Ω 50Ω COAX CH A CH B OSCILLOSCOPE ECL/TTL PROPAGATION DELAY — SINGLE ENDED 50% VIN Tpd– – Tpd++ 1.5V VOUT ECL/TTL WAVEFORMS: RISE AND FALL TIMES 2.0V 0.8V VOUT Trise M9999-032906 hbwhelp@micrel.com or (408) 955-1690 Tfall 6 Precision Edge® SY10H841 SY100H841 Micrel, Inc. 16-PIN SOIC .300" WIDE (Z16-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. M9999-032906 hbwhelp@micrel.com or (408) 955-1690 7