SY10EP451LTG-TR

SY10/100EP451L 3.3V ECL 6-Bit Differential Register with Master Reset General Description Features The SY10/100EP451L is a 6-bit fully differential register with common clock and single-ended Master Reset (MR). It is ideal for very high frequency applications where a registered data path is necessary. All inputs have an internal 75kΩ pull-down resistor. Differential inputs have an override clamp. Unused differential register inputs can be left open and will default LOW. When the differential inputs are forced to a value smaller than VEE +1.2V, the clamp will override and force the output to a default state. The positive transition of CLK (pin 4) will latch the registers. Master Reset (MR) HIGH will asynchronously reset all registers forcing Q outputs to go LOW. Datasheets and support documentation can be found on Micrel’s web site at: www.micrel.com. • • • • • • • • • 450ps typical propagation delay Maximum frequency > 3.0GHz typical Asynchronous Master Reset 20ps skew within device, 35ps skew device-to-device PECL mode operating range: – VCC = 3.0V to 3.6V with VEE = 0V NECL mode operating range: – VCC = 0V with VEE = –3.0V to –3.6V Open input default state Safety clamp on inputs Available in 32-pin TQFP Applications • High Speed Logic • Wireless Communication Systems • Data Communication Systems Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com May 2007 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY10/100EP451L Logic Diagram May 2007 2 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY10/100EP451L Ordering Information(1) Part Number SY10EP451LTG SY10EP451LTGTR (2) SY100EP451LTG (2) SY100EP451LTGTR Package Type Operating Range Package Marking Lead Finish T32-1 Industrial SY10EP451LTG with Pb-Free bar-line indicator Pb-Free NiPdAu T32-1 Industrial SY10EP451LTG with Pb-Free bar-line indicator Pb-Free NiPdAu T32-1 Industrial SY100EP451LTG with Pb-Free bar-line indicator Pb-Free NiPdAu T32-1 Industrial SY100EP451LTG with Pb-Free bar-line indicator Pb-Free NiPdAu Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. Pin Configuration 32-Pin TQFP (T32-1) May 2007 3 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY10/100EP451L Pin Description Pin Number Pin Name 2, 3 D0, /D0 Pin Function 32, 1 D1, /D1 30, 31 D2, /D2 26, 27 D3, /D3 24, 25 D4, /D4 22, 23 D5, /D5 29 MR 4, 5 CLK, /CLK 7, 8 Q0, /Q0 9, 10 Q1, /Q1 11, 12 Q2, /Q2 14, 15 Q3, /Q3 17, 18 Q4, /Q4 20, 21 Q5, /Q5 6, 13, 16 VCC Positive Supply: Bypass with 0.1µF||0.01µF low ESR capacitors as close to the VCC pins as possible. 19, 28 VEE Negative Power Supply: VEE must be tied to most negative supply. May 2007 ECL Differential Data Inputs: These input pairs are the different data signal inputs to the device. Each input pin is connected to a 75kΩ pull-down resistor. Due to an internal clamping circuit, D will default LOW and /D will default HIGH if left open. ECL Master Reset Input pin. If input pin is left open, it will default to LOW. ECL Differential Clock Input: This input pair is the clock signal input to the device. Each input pin is connected to a 75kΩ pull-down resistor. Due to an internal clamping circuit, CLK will default LOW and /CLK will default HIGH if left open. ECL Differential Data Outputs: Q defaults to LOW and /Q defaults to HIGH if D inputs are left open. See “LVPECL Output Interface Applications” section for recommendations on terminations. 4 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY10/100EP451L Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage PECL Mode (VCC) ............................................................... +4V NECL Mode (VEE) ............................................................... –4V Input Voltage (VIN) PECL Mode ..........................................................................VCC NECL Mode ......................................................................... VEE Output Current (IOUT) Continuous........................................................................ 50mA Surge............................................................................... 100mA Lead Temperature (soldering, 20sec.) ....................................260°C Storage Temperature (Ts)...................................... –65°C to +150°C Supply Voltage (VCC) PECL Mode (VEE = 0V) ..................................... +3.0V to +3.6V Supply Voltage (VEE) NECL Mode (VCC = 0V)....................................... -3.0V to -3.6V Ambient Temperature (TA)....................................... –40°C to +85°C (3) Junction Thermal Resistance TQFP Junction-to-Ambient (θJA) 0lfpm......................................................................... 80°C/W 500lfpm .................................................................... 66°C/W Junction-to-Case (θJC) .................................................. 20°C/W PECL 10EP DC Electrical Characteristics(4) (5) VCC = 3.3V; VEE = 0V; TA = –40°C to +85°C, unless otherwise stated. -40°C Symbol IEE Parameter Min Typ 80 105 2165 2290 1490 Power Supply Current (6) 25°C Max 85°C Min Typ Max 80 105 2415 2230 2355 1615 1430 1555 Max Units 80 105 mA 2415 2540 mV 1740 mV Min Typ 2480 2290 1680 1470 1615 VOH Output HIGH Voltage VOL Output LOW Voltage 1365 VIH Input HIGH Voltage (Single-Ended) 2090 2415 2155 2480 2215 2540 mV VIL Input LOW Voltage (Single-Ended) 1365 1690 1430 1755 1490 1815 mV VIHCMR Input HIGH Voltage Common Mode (7) Range (Differential Configuration) 2.0 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 µA IIL Input LOW Current (6) 150 0.5 150 0.5 0.5 µA NECL 10EP DC Electrical Characteristics(4) VCC = 0V; VEE = –3.0V to –3.6V; TA = –40°C to +85°C, unless otherwise stated. -40°C Symbol Parameter Typ Max 80 105 -1135 -1010 -885 Output LOW Voltage -1935 -1810 VIH Input HIGH Voltage (Single-Ended) -1210 VIL Input LOW Voltage (Single-Ended) -1935 VIHCMR Input HIGH Voltage Common Mode (7) Range (Differential Configuration) IIH Input HIGH Current IIL Input LOW Current IEE Power Supply Current VOH Output HIGH Voltage VOL (6) (6) Min 25°C Typ Max Units 80 105 mA -1010 -885 -760 mV -1620 -1830 -1685 -1560 mV -820 -1085 -760 mV -1545 -1810 -1485 mV 0.0 V 150 µA Typ Max 80 105 -1070 -945 -820 -1685 -1870 -1745 -885 -1145 -1610 -1870 VEE +2.0 0.0 Min 85°C VEE +2.0 150 0.5 0.0 Min VEE +2.0 150 0.5 0.5 µA Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. θJA and θJC values are determined for a 4-layer board in still-air unless otherwise stated. 4. 5. 6. 7. The device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specifications limit values are applied individually under normal operating conditions and not valid simultaneously. Input and output parameters vary 1:1 with VCC. All loading with 50Ω to VCC–2.0V. VIHCMR (min) varies 1:1 with VEE, VIHCMR (max) varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. May 2007 5 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY10/100EP451L PECL 100EP DC Electrical Characteristics(8) (9) VCC = 3.3V; VEE = 0V; TA = –40°C to +85°C, unless otherwise stated. -40°C Symbol IEE Parameter Min Typ 85 120 2155 2280 1480 Power Supply Current (10) 25°C Max 85°C Min Typ Max 85 120 2405 2155 2280 1605 1355 1480 Max Units 85 120 mA 2280 2405 mV 1605 mV Min Typ 2405 2155 1605 1355 1480 VOH Output HIGH Voltage VOL Output LOW Voltage 1355 VIH Input HIGH Voltage (Single-Ended) 2075 2420 2075 2420 2075 2420 mV VIL Input LOW Voltage (Single-Ended) 1355 1675 1355 1675 1355 1675 mV VIHCMR Input HIGH Voltage Common Mode (11) Range (Differential Configuration) 2.0 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 µA IIL Input LOW Current (10) 150 0.5 150 0.5 0.5 µA NECL 100EP DC Electrical Characteristics(8) VCC = 0V; VEE = –3.0V to –3.6V; TA = –40°C to +85°C, unless otherwise stated. -40°C Symbol IEE Parameter Min Typ 85 120 -1145 -1020 -1820 Power Supply Current (10) 25°C Max 85°C Min Typ Max 85 120 -895 -1145 -1020 -1695 -1945 -1820 Max Units 85 120 mA -1020 -895 mV -1695 mV Min Typ -895 -1145 -1695 -1945 -1820 VOH Output HIGH Voltage VOL Output LOW Voltage -1945 VIH Input HIGH Voltage (Single-Ended) -1225 -880 -1225 -880 -1225 -880 mV VIL Input LOW Voltage (Single-Ended) -1945 -1625 -1945 -1625 -1945 -1625 mV 0.0 V 150 µA (10) VIHCMR Input HIGH Voltage Common Mode (11) Range (Differential Configuration) IIH Input HIGH Current IIL Input LOW Current VEE +2.0 0.0 VEE +2.0 150 0.5 0.0 VEE +2.0 150 0.5 0.5 µA Notes: 8. The device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specifications limit values are applied individually under normal operating conditions and not valid simultaneously. 9. Input and output parameters vary 1:1 with VCC. 10. All loading with 50Ω to VCC–2.0V. 11. VIHCMR (min) varies 1:1 with VEE, VIHCMR (max) varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. May 2007 6 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY10/100EP451L AC Electrical Characteristics(12) VCC = 0V; VEE = –3.0V to –3.6V or VCC = 3.0V to 3.6V; VEE = 0V; TA = –40°C to +85°C; for 10EP and 100EP, unless (13) otherwise stated. -40°C Symbol Parameter VOUTpp Output Voltage Amplitude at 3GHz tPD Propagation Delay to Output Differential tRR Reset Recovery tS (14) Min Typ 25°C Max Min Typ 520 650 350 400 450 550 85°C Max Min Typ 450 580 390 440 490 590 Max Units 540 670 CLK to Q, /Q MR to Q, /Q 330 380 430 530 MR to CLK 240 100 250 100 260 100 ps Set-Up Time D to CLK 80 0 80 0 80 0 ps tH Hold Time CLK to D 80 0 80 0 80 0 ps tPW Minimum Pulse Rate MR 400 530 630 550 650 400 (15) mV 590 690 400 ps ps tSKEW Within-Device Skew (16) Device-to-Device Skew 10 35 40 100 10 35 40 100 10 35 40 100 ps tJITTER Clock Random Jitter (RMS) at ≤3.0GHz 0.2 1 0.2 1 0.2 1 ps tr, tf Output Rise/Fall Times (20% to 80%) 150 250 160 260 180 280 ps Q, /Q 100 110 130 Notes: 12. The device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specifications limit values are applied individually under normal operating conditions and not valid simultaneously. 13. Measured using a 750mV source, 50% duty cycle clock source, all loading with 50Ω to VCC–2V. 14. VOL and VOH specifications not guaranteed for fMAX testing 15. Skew is measured between outputs under identical transitions and conditions on any one device. 16. Device-to-device skew for identical transitions at identical VCC levels. Input Stage Figure 1. Simplified Differential Input Buffer May 2007 7 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY10/100EP451L Typical Characteristics VCC = 3.3V, GND = 0V, VIN = 800mV, TA = 25°C; for 10EP and 100EP, unless otherwise stated. Functional Characteristics VCC = 3.3V, GND = 0V, VIN = 800mV, TA = 25°C; for 10EP and 100EP, unless otherwise stated. May 2007 8 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY10/100EP451L LVPECL Output Interface Applications LVPECL output has very low output impedance (open emitter), and small signal swing which results in low EMI. LVPECL is ideal for driving 50Ω and 100Ω controlled impedance transmission lines. There are several techniques in terminating the LVPECL output, as shown in Figures 2 through 4. Figure 4. Terminating Unused I/O Notes: 1. Unused output (/Q) must be terminated to balance the output. 2. Unused output pairs (Q and /Q) may be left floating. Figure 2. Parallel Termination-Thevenin Equivalent Figure 3. Three-Resistor “Y-Termination” Notes: 1. Power-saving alternative to Thevenin termination. 2. Place termination resistors as close to destination inputs as possible. 3. Rb resistor sets the DC bias voltage, equal to VCC-2V. 4. C1 is an optional bypass capacitor intended to compensate for any tr, tf mismatches. May 2007 9 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY10/100EP451L Package Information 32-Pin TQFP (T32-1) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2007 Micrel, Incorporated. May 2007 10 M9999-051807-B hbwhelp@micrel.com or (408) 955-1690