SY10H607JZ

NOT RECOMMENDED FOR NEW DESIGNS Differential PECL data and clock inputs 48mA sink, 15mA source TTL outputs Single +5V power supply Multiple power and ground pins to minimize noise Specified within-device skew VBB output for single-ended use Fully compatible with MC10H/100H607 Available in 28-pin PLCC package The SY10/100H607 are 6-bit, registered, dual supply PECL-to-TTL translators. The devices feature differential PECL inputs for both data and clock. The TTL outputs feature 48mA sink, 15mA source drive capability for driving high fanout loads. The asynchronous master reset control is a PECL level input. With its differential PECL inputs and TTL outputs, the H607 device is ideally suited for the receive function of a HPPI bus-type board-to-board interface application. The on-chip registers simplify the task of synchronizing the data between the two boards. The device is available in either ECL standard: the 10H device is compatible with 10K logic levels, while the 100H device is compatible with 100K logic levels. BLOCK DIAGRAM PIN NAMES Pin 1 OF 6 BITS Dn Dn SY100H607 DESCRIPTION FEATURES ■ ■ ■ ■ ■ ■ ■ ■ SY10H607 SY100H607 SY10H607 REGISTERED HEX PECL-TO-TTL Micrel, Inc. D Q Qn CLK R CLK Function D0 – D5 True PECL Data Inputs D0 – D5 Inverted PECL Data Inputs CLK, CLK Differential PECL Clock Input MR PECL Master Reset Input Q0 – Q5 TTL Outputs VCCE PECL VCC (5.0V) VCCT TTL VCC (5.0V) TGND TTL Ground EGND PECL Ground VBB VBB Reference Output (PECL) CLK MR VBB M9999-032906 hbwhelp@micrel.com or (408) 955-1690 1 Rev.: G Amendment: /0 Issue Date: March 2006 SY10H607 SY100H607 Micrel, Inc. TGND Ordering Information(1) Q5 VCCT MR VCCT Q4 Q3 PACKAGE/ORDERING INFORMATION 25 24 23 22 21 20 19 Q2 26 18 Q1 Q0 27 17 28 16 15 14 3 13 4 12 D0 5 6 7 8 9 10 11 D4 D4 VCCE D3 D3 Package Type Operating Range Package Marking Lead Finish SY10H607JC J28-1 Commercial SY10H607JC Sn-Pb SY10H607JCTR(2) J28-1 Commercial SY10H607JC Sn-Pb SY100H607JC J28-1 Commercial SY100H607JC Sn-Pb SY100H607JCTR(2) J28-1 Commercial SY100H607JC Sn-Pb SY10H607JZ(3) J28-1 Commercial SY10H607JZ with Pb-Free bar-line indicator Matte-Sn SY10H607JZTR(2, 3) J28-1 Commercial SY10H607JZ with Pb-Free bar-line indicator Matte-Sn SY100H607JZ(3) J28-1 Commercial SY100H607JZ with Pb-Free bar-line indicator Matte-Sn SY100H607JZTR(2, 3) J28-1 Commercial SY100H607JZ with Pb-Free bar-line indicator Matte-Sn D2 D2 CLK VBB TOP VIEW PLCC 1 2 D0 EGND D1 D1 TGND CLK D5 D5 Part Number 28-Pin PLCC (J28-1) Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-032906 hbwhelp@micrel.com or (408) 955-1690 2 SY10H607 SY100H607 Micrel, Inc. TRUTH TABLE Dn MR TCLK/CLK Qn + 1 L L Z L H L Z H X H X L Z = Low to High Transition. DC ELECTRICAL CHARACTERISTICS VCCT = VCCE = 5.0V ±5% TA= 0°C Symbol TA= +25°C TA= + 85°C Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. PECL Power Supply Current 10H 100H — — 70 65 85 80 — — 70 70 85 85 — — 70 75 85 95 ICCL TTL Supply Current — 100 120 — 100 120 — 100 120 ICCH TTL Supply Current — 100 120 — 100 120 — 100 120 mA IOS Output Short Circuit Current –100 — –225 –100 — –225 –100 — –225 mA IEE Unit Condition mA mA 10H PECL DC ELECTRICAL CHARACTERISTICS(1) VCCT = VCCE = 5.0V ±5% TA= 0°C Symbol Parameter TA= +25°C TA= + 85°C Min. Max. Min. Max. Min. Max. Unit Condition IIH Input HIGH Current — 225 — 145 — 145 µA IIL Input LOW Current 0.5 — 0.5 — 0.5 — µA VIH Input HIGH Voltage 3830 4160 3870 4190 3930 4280 mV VCCT = 5.0V VIL Input LOW Voltage 3050 3520 3050 3520 3050 3555 mV VCCT = 5.0V VBB Output Bias Voltage 3620 3730 3650 3750 3690 3810 mV VCCT = 5.0V Condition Note: 1. PECL VIL, VIH, VOL, VOH, VBB are given for VCCT = VCCE = 5.0V and will vary 1:1 with power supply. 100H PECL DC ELECTRICAL CHARACTERISTICS(1) VCCT = VCCE = 5.0V ±5% TA= 0°C Symbol Parameter TA= +25°C TA= + 85°C Min. Max. Min. Max. Min. Max. Unit IIH Input HIGH Current — 225 — 145 — 145 µA IIL Input LOW Current 0.5 — 0.5 — 0.5 — µA VIH Input HIGH Voltage 3835 4120 3835 4120 3835 4120 mV VCCT = 5.0V VIL Input LOW Voltage 3190 3525 3190 3525 3190 3525 mV VCCT = 5.0V VBB Output Bias Voltage 3620 3740 3620 3740 3620 3740 mV VCCT = 5.0V Note: 1. PECL VIL, VIH, VOL, VOH, VBB are given for VCCT = VCCE = 5.0V and will vary 1:1 with power supply. M9999-032906 hbwhelp@micrel.com or (408) 955-1690 3 SY10H607 SY100H607 Micrel, Inc. 10H/100H TTL DC ELECTRICAL CHARACTERISTICS(1) VCCT = VCCE = 5.0V ±5% TA= 0°C Symbol Parameter TA= +25°C TA= + 85°C Min. Max. Min. Max. Min. Max. Unit Condition VOH Output HIGH Voltage 2.5 2.0 — — 2.5 2.0 — — 2.5 2.0 — — V IOH = –15mA IOH = –24mA VOL Output LOW Voltage — 0.55 — 0.55 — 0.55 V IOL = 48mA Note: 1. DC levels such as VOH, VOL, etc., are standard for PECL and FAST devices, with the exceptions of: IOL =48mA at 0.5 VOL; and IOH = 24mA at 2.0 VOH. AC ELECTRICAL CHARACTERISTICS(1) VCCT = VCCE = 5.0V ±5% TA= 0°C Symbol tPD tskpp TA= +25°C TA= + 85°C Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Propagation Delay to Output CLK to Q MR to Q — — — — 6.0 6.0 — — — — 6.0 6.0 — — — — 6.0 6.0 Part-to-Part Skew(1,4) Unit Condition ns CL = 50 pF — — 0.5 — — 0.5 — — 0.5 ns CL = 50pF Within-Device Skew(2,4) — — 0.3 — — 0.3 — — 0.3 ns CL = 50pF tskew– – Within-Device Skew(3,4) — — 0.3 — — 0.3 — — 0.3 ns CL = 50pF tS Set-up Time 0.200 — — 0.200 — — 0.200 — — ns tH Hold Time 0.500 — — 0.500 — — 0.500 — — ns tPW Minimum Pulse Width CLK, MR 1.0 — — 1.0 — — 1.0 — — VPP Minimum Input Swing 200 150 — 200 150 — 200 150 — mV tr tf Rise/Fall Time 1.0V to 2.0V — — 1.5 — — 1.5 — — 1.5 ns fMAX Max. Input Frequency(5,6) 160 — — 160 — — 160 — — MHz tskew++ ns CL = 50pF Notes: 1. Device-to-Device Skew considering HIGH-to-HIGH transitions at common VCC level. 2. Within-Device Skew considering HIGH-to-HIGH transitions at common VCC level. 3. Within-Device Skew considering LOW-to-LOW transitions at common VCC level. 4. All skew parameters are guaranteed but not tested. 5. Frequency at which output levels will meet a 0.8V to 2.0V minimum swing. 6. The fMAX value is specified as the minimum guaranteed maximum frequency. Actual operational maximum frequency may be greater. M9999-032906 hbwhelp@micrel.com or (408) 955-1690 4 SY10H607 SY100H607 Micrel, Inc. 28-PIN PLCC (J28-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. M9999-032906 hbwhelp@micrel.com or (408) 955-1690 5