SY88992LMG

SY88992L 3.3V, 4.25Gbps VCSEL Driver General Description Features The SY88992L is a single supply 3.3V, low power consumption, small-form factor VCSEL driver ideal for use in datacom applications; Ethernet, GbE (Gigabit Ethernet), and FC (Fibre Channel) applications that operate from 100Mbps up to 4.25Gbps. The modulation current is set by applying an external voltage at the IM_SET pin. The driver features an adjustable peaking option with variable amplitude and duration to improve VCSEL edge response. The driver can deliver modulation current up to 25mA and a peaking current up to 35% of the modulation current. This device is intended to be used with Micrel’s MIC3001 Optical Transceiver Management IC, which allows for both modulation and bias current control and monitoring, APC (Automatic Power Control), and temperature compensation. All support documentation can be found on Micrel’s web site at: www.micrel.com. • Up to 25mA modulation current • Operates from 100Mbps to 4.25Gbps • Peaking with variable duration option for better VCSEL response • Dual peaking, on the rise and falling edges • Peaking current proportional to modulation current • Easy modulation current setting • Fully controllable with Micrel MIC3001 • Small (3mm x 3mm) 16 pin QFN package Applications • Multirate LAN, SAN applications up to 4.25Gbps: Ethernet, GbE, FC • SFF, SFP Modules Markets • Datacom ________________________________________________________________ Typical Application January 2006 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L Functional Block Diagram Ordering Information(1) Part Number SY88992LMG (2) SY88992LMGTR Package Type Operating Range Package Marking Lead Finish QFN-16 Industrial 992L with Pb-Free bar-line indicator NiPdAu Pb-Free QFN-16 Industrial 992L with Pb-Free bar-line indicator NiPdAu Pb-Free Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = +25°C, DC Electricals only. 2. Tape and Reel. Pin Configuration 16-Pin QFN January 2006 2 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L Pin Description Pin Number Pin Name Pin Function 2 DIN+ Non-Inverting Input Data. Internally terminated with 50Ω to a reference voltage. 3 DIN- Inverting Input Data. Internally terminated with 50Ω to a reference voltage. 6 IP_SET1 Peaking Current Setting. Connect this pin to GND and keep pins 7 and 8 open to set peaking-to-modulation current ratio to 5%. Combinations of the three pins, as shown in table below, will set different ratios up to 35%. 7 IP_SET2 Peaking Current Setting. Connect this pin to GND and keep pins 6 and 8 open to set peaking-to-modulation current ratio to 10%. Combinations of the three pins, as shown in table below, will set different ratios up to 35%. 8 IP_SET3 Peaking Current Setting. Connect this pin to GND and keep pins 6 and 7 open to set peaking-to-modulation current ratio to 20%. Combinations of the three pins, as shown in table below, will set different ratios up to 35%. 10 MOD- Inverted Modulation Current Output. Provides modulation current when input data is negative. 11 MOD+ Non-Inverted Modulation Current Output. Provides modulation current when input data is positive. 13 IM_SET Modulation Current Setting. The modulation current is set by applying a 0V to 1.2V voltage at this pin. 14 IPD_SET Peaking Duration Setting. The peaking current duration is set by installing a resistor between this pin and ground. The plot on page 6 shows peaking duration versus the value of the resistor installed. 16 /EN A low level signal applied to this pin will enable the output stage of the driver. Internally pulled down to ground with 75kΩ resistor. 1, 4, 9, 12 GND Ground. Ground and exposed pad must be connected to the plane of the most negative potential. 5, 15 VCC Supply Voltage. Bypass with a 0.1µF//0.01µF low ESR capacitor as close to VCC pin as possible. Truth Table MOD+ (1) DIN+ DIN- /EN MOD- VCSEL Output L H L H L L H L L L H H X X H H H L (2) Notes: 1. IMOD = 0 when MOD+ = H. 2. Assuming a common anode VCSEL with its cathode tied to MOD+. Peaking Current-to-Modulation Current Ratio Setting IP/IMOD 0% 5% 10 % 15 % 20 % 25 % 30 % 35 % IP_SET1 NC GND NC GND NC GND NC GND IP_SET2 NC NC GND GND NC NC GND GND IP_SET3 NC NC NC NC GND GND GND GND January 2006 3 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VIN) ........................... –0.5V to +4.0V CML Input Voltage (VIN) .......... VCC–1.2V to VCC+0.5V TTL Control Input Voltage (VIN) ...................0V to VCC Lead Temperature (soldering, 20sec.) ........... +260°C Storage Temperature (Ts) ............... –65°C to +150°C Supply Voltage (VCC) .......................... +3.0V to +3.6V Ambient Temperature (TA) ................ –40°C to +85°C (3) Package Thermal Resistance QFN (θJA) Still-air .............................................. 60°C/W (ψJB) ......................................................... 33°C/W DC Electrical Characteristics TA = -40°C to 85°C and VCC = 3.0V to 3.6V, unless otherwise noted. Typical values are at: VCC = 3.3V, TA = 25°C, (4) IMOD = 13mA Symbol Parameter ICC Power Supply Current (4) Condition Min Max Units Peaking not used 57 95 mA Maximum peaking used 70 110 mA 25 mA 100 µA IMOD Modulation Current AC-coupled IMOD_OFF Modulation OFF Current Current at MOD+ and MOD- when the part is disabled VMOD_MIN Minimum Voltage required at the driver output (headroom) for proper operation 1.5 RIN Input Resistance (DIN+-to-DIN-) 90 VID Differential Input Voltage Swing VIM_SET Voltage Range on IM_SET VIL /EN Input Low VIH Typ 3 V 100 200 (4) IMOD range 3mA – 25mA /EN Input High 2 Input Impedance at /EN 110 Ω 2400 mVPP 1.2 V 0.8 V V 75 kΩ Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Package Thermal Resistance assumes exposed pad is soldered (or equivalent) to the devices most negative potential on the PCB. θJB uses a 4-layer and θJA in still air unless otherwise stated. 4. IMOD is defined as the current at the output of the driver. That current splits between the pull-up network at the output and the VCSEL. For a nominal pull-up resistor of 75Ω at the output of the driver and a nominal 50Ω VCSEL equivalent resistor, 60% of that current goes to the VCSEL. January 2006 4 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L AC Electrical Characteristics TA = -40°C to +80°C and VCC = 3.0 to 3.6V, unless otherwise noted. Typical values are at VCC = 3.3V, TA = 25°C, (5) IMOD = 13mA , and AC-coupled 50Ω load to ground with 75Ω pull-up (see Figure below). Symbol tOFF (6) (7) tON tr tf (IP / IMOD) Parameter Condition Min Data Rate NRZ 0.1 Turn OFF Time 50Ω load Turn ON Time Output Current Rise Time Output Current Fall Time Typ Max Units 4.25 Gbps 1 1.5 ns 50Ω load 1.8 2.5 ns 20% to 80%, IMOD = 13mA, no peaking, 50Ω load 65 95 ps 20% to 80%, IMOD = 13mA, IP/IMOD=20%, RIPD=1.5kΩ 60 75 ps 20% to 80%, IMOD = 13mA, no peaking, 50Ω load 65 95 ps 20% to 80%, IMOD = 13mA, IP/IMOD=20%, RIPD=1.5kΩ 60 75 ps Total Jitter @ 2.5Gbps data rate, 50Ω load 30 psPP Pulse-Width Distortion 50Ω load 20 ps Max Maximum Peaking Current-toModulation Current Ratio tP Peaking Current Duration (8) IMOD = 13mA, RIPD_SET = 0Ω 35 % 150 ps Notes: 5. IMOD is defined as the current at the output of the driver. That current splits between the pull-up network at the output and the VCSEL. For a nominal pull-up resistor of 75Ω at the output of the driver and a nominal 50Ω VCSEL equivalent resistor, 60% of that current goes to the VCSEL. 6. Turn-OFF time is defined as the delay between the time the signal at /EN rises to 50% of its amplitude and the time when the output of the driver reaches 10% of its steady-state amplitude. 7. Turn-ON time is defined as the delay between the time the signal at /EN falls to 50% of its amplitude and the time when the output of the driver reaches 90% of its steady-state amplitude. 8. The peaking current duration is the time between the start of the peaking current, which is the same as the start of the modulation current transition, and the time when the peaking current reaches its maximum, i.e., the top of the peak. Test Circuit January 2006 5 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L Typical Operating Characteristics TA = +25°C and VCC = 3.3V, unless otherwise noted. IMOD = 0mA RIPD_SET (kΩ) January 2006 6 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L Typical Waveforms January 2006 7 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L Peaking Variation with IP/IMOD Ratio and Peaking Duration Increasing Peaking Percentage As it can be seen on the set of electrical waveforms below, the amplitude of the peak increases with the peakingto-modulation current ratio and the width of the peak increases with peaking duration. Increasing Peaking Duration January 2006 8 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L Input and Output Stages Figure 1b. Simplified Output Stage Figure 1a. Simplified Input Stage Interfacing the Input to Different Logic Drivers Figure 2b. AC-Coupling to CML Driver Figure 2a. AC-Coupling to LVPECL Driver January 2006 9 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L and almost all the modulation current goes into the VCSEL. However, using the inductor alone will cause signal distortion. To avoid this, a combination of resistors and inductors can be used, as shown on figure 3. In this case, the headroom of the driver is VCC–R1 x αIMOD, where αIMOD is the portion of the modulation current that goes through the pull-up network. For instance, if a modulation current out of the driver of 25mA is considered, with a pull-up resistor of 75Ω, and the VCSEL with the damping resistor total resistance is 50Ω, then the modulation current will split; 10mA to the pull-up resistor and 15mA to the laser. The headroom for the driver will be VCC–75 x 10 = VCC–750mV which is way higher than the minimum voltage required for the output stage of the driver to operate properly. Driver’s Special Features The SY88992L features a peaking current of programmable amplitude and duration on both the rising and the falling edges. The amplitude of the peaking current is adjustable in steps of 5% of the modulation current from 0% to 35%. As shown in the table on page 3, the ratio between the peaking current and the modulation current (IP/IMOD) can be programmed by connecting pin 6 (IP_SET1) and/or pin 7 (IP_SET2) and/or pin 8 (IP_SET3) to ground. When all these three pins are left open, there is no peaking (ratio 0%). When they’re all connected to ground the ratio is maximum (35%). For each family of VCSELs used with the driver, the user must try many combinations in order to get the best response for the VCSEL. The peaking current duration can be tuned by installing a resistor between pin 14 and ground; 0Ω provides maximum duration and 3kΩ or higher provides the minimum duration. The combined features will improve the VCSEL response for a better optical signal quality. The electrical eye diagrams on page 8 show how the signal changes as the peaking-to-modulation current varies. The coupling capacitor creates a low-frequency cutoff in the circuit. Therefore, a proper coupling capacitor value must be chosen to accommodate different data rates in the application. If the value of the capacitor is too high, it may cause problems in high data rate applications. If its value is too small, it won’t be able to hold a constant charge between the first bit and the last bit in a long string of identical bits in low data rate application. Both cases lead to higher patterndependent jitter in the transmitter signal. 0.1µF is found to be good for applications from 155Mbps to 4.25Gbps. Application Hints The typical application section on the front page shows how to connect the driver to the VCSEL single-ended. To improve transition time and VCSEL response, the VCSEL can be driven differentially, as shown in Figure 3. Driving the VCSEL differentially will also minimize the cross talk with the rest of the circuitry on the board, especially with the receiver. The driver is always AC-coupled to the VCSEL and the headroom of the driver is determined by the pull-up network at the output. In Figure 3, the modulation current out of the driver is split between the pull-up network and the VCSEL. If, for example, the total pullup resistor is twice the sum of the damping resistor and VCSEL equivalent series resistance, only two thirds (2/3) of the modulation current will be used by the VCSEL. Therefore, to maximize the modulation current going through the VCSEL, the total pull-up resistors should be kept as high as possible. One solution consists of using an inductor alone as pull-up, creating a high impedance path for the modulation current and zero ohm (0Ω) path for the DC current. This offers a headroom equal to VCC for the driver January 2006 Figure 3. Driving a Common Anode VCSEL Differentially 10 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88992L Package Information 16-Pin (3mm x 3mm) QFN MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. January 2006 M9999-011306-A hbwhelp@micrel.com or (408) 955-1690