TC1272AMVNBTR

TC1272A 3-Pin Reset Monitor Features General Description • • • • • • The TC1272A are cost-effective system supervisor circuits designed to monitor VDD in digital systems and provide a reset signal to the host processor, when necessary. No external components are required. Precision VDD Monitor 140 msec Minimum RESET, Output Duration Output Valid to VDD = 1.2V VDD Transient Immunity Small 3-Pin SOT-23B Package No External Components Applications • • • • Computers Embedded Systems Battery-Powered Equipment Critical µP Power Supply Monitoring The reset output is driven active within 65 µsec (typ.) of VDD falling through the reset voltage threshold. RESET is maintained active for a minimum of 140 msec after VDD rises above the reset threshold. The TC1272A has a complimentary output. The output of the TC1272A is valid down to VDD = 1.2V. The device is available in a 3-Pin SOT-23B package. The TC1272A device is optimized to reject fast transient glitches on the VDD line. Package Type Typical Application Circuit 3-Pin SOT-23B* VDD 2 VDD RESET VDD 1 RESET 1 RESET Input TC1272A Processor GND GND TC1272A 3 GND VDD 2 3 Note: 3-Pin SOT-23B is equivalent to JEDEC TO-236.  2004-2012 Microchip Technology Inc. DS21877B-page 1 TC1272A 1.0 ELECTRICAL CHARACTERISTICS † Notice: Stresses above those listed under “Maximum ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings† Supply Voltage (VDD to GND) ..........................................6.0V RESET .................................................. –0.3V to (VDD +0.3V) PIN FUNCTION TABLE Input Current, VDD.........................................................20 mA Output Current, RESET ................................................20 mA NAME dV/dt (VDD) ............................................................. 100V/µsec Operating Temperature Range..................... –40°C to +125°C Power Dissipation (TA = 70°C): 3-Pin SOT-23B (derate 4 mW/°C above +70°C) ....320 mW FUNCTION GND Ground RESET RESET push-pull output remains low while VDD is below the reset voltage threshold and for 140 msec (min.) after VDD rises above reset threshold Storage Temperature Range ........................ –65°C to +150°C Maximum Junction Temperature, TJ .............................. 150°C VDD ELECTRICAL CHARACTERISTICS VDD = Full Range, TA = Operating Temperature Range, unless otherwise noted. Typical values are at TA = +25°C, VDD = 5V for L/M/J, 3.3V for T/S, 3.0V for R and 2.5V for Z (Note 1). Parameter Sym Min Typ Max Units 1.0 — 5.5 V 1.2 — 5.5 — 12 30 — 9 25 4.56 4.63 4.70 4.50 — 4.75 4.31 4.38 4.45 V 4.25 — 4.50 V 3.93 4.00 4.06 V 3.89 — 4.10 V 3.04 3.08 3.11 V 3.00 — 3.15 V 2.89 2.93 2.96 V 2.85 — 3.00 V 2.59 2.63 2.66 V 2.55 — 2.70 V 2.28 2.32 2.35 V 2.25 — 2.38 V Reset Threshold Tempco — 30 — ppm/°C VDD to Reset Delay, — 65 — µsec 140 320 560 msec — — 0.3 V — — 0.4 — — 0.3 0.8 VDD — — VDD – 1.5 — — VDD Range Supply Current Reset Threshold (Note 2) ICC VTH Reset Active Time Out Period RESET Output Voltage Low RESET Output Voltage High VOL VOH Test Conditions TA = 0°C to +70°C TA = – 40°C to +125°C µA TC1272AL/M/J: VDD < 5.5V TC1272AR/S/T/Z: VDD < 3.6V V TC1272AL: TA = +25°C TA = – 40°C to +125°C TA = +25°C TC1272AM: TA = – 40°C to +125°C TC1272AJ: TA = +25°C TA = – 40°C to +125°C TA = +25°C TC1272AT: TA = – 40°C to +125°C TA = +25°C TC1272AS: TA = – 40°C to +125°C TC1272AR: TA = +25°C TA = – 40°C to +125°C TA = +25°C TC1272AZ: TA = – 40°C to +125°C VDD = VTH to (VTH – 100 mV) (Note 2) TC1272AR/S/T/Z: VDD = VTH min, ISINK = 1.2 mA TC1272AL/M/J: VDD = VTH min, ISINK = 3.2 mA VDD > 1.0V, ISINK = 50 µA V TC1272AR/S/T/Z: VDD > VTH max, ISOURCE = 500 µA TC1272AL/M/J: VDD > VTH max, ISOURCE = 800 µA Note 1: Production testing done at TA = +25°C, overtemperature limits ensured by QC screen. 2: RESET Output for TC1272A. DS21877B-page 2  2004-2012 Microchip Technology Inc. TC1272A 2.0 TYPICAL PERFORMANCE CHARACTERISTICS Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 18 TC1272A/R/S/T/Z, No Load 450 16 Power-up Reset Timeout (µsec) VDD = 5V Supply Current ( µA) 14 12 10 VDD = 3V 8 6 4 VDD = 1V 2 400 350 300 250 200 150 100 50 0 -40 -20 0 20 40 60 80 100 0 120 -40 -20 0 20 Temperature (°C) FIGURE 2-1: Temperature. 40 60 80 100 120 Temperature (°C) FIGURE 2-3: vs. Temperature. Supply Current vs. 16 Power-up Reset Time Out 1.001 TC1272A/L/M/J, No Load VDD = 5V Normalized Reset Threshold Supply Current ( µA) 14 12 10 VDD = 3V 8 6 VDD = 1V 4 2 0 1 0.999 0.998 0.997 -40 -20 0 20 40 60 80 100 Temperature (°C) FIGURE 2-2: Temperature. Supply Current vs.  2004-2012 Microchip Technology Inc. 120 -40 -20 0 20 40 60 80 100 120 Temperature (°C) FIGURE 2-4: Normalized Reset Threshold vs. Temperature. DS21877B-page 3 TC1272A 3.0 APPLICATIONS INFORMATION 3.1 VDD Transient Rejection The TC1272A provides accurate VDD monitoring and reset timing during power-up, power-down and brownout/sag conditions. These devices also reject negativegoing transients (glitches) on the power supply line. Figure 3-1 shows the maximum transient duration vs. maximum negative excursion (overdrive) for glitch rejection. Any combination of duration and overdrive that lies under the curve will not generate a reset signal. VDD VTH Overdrive Maximum Transient Duration (µsec) Duration 3.2 RESET Signal Integrity During Power-Down The TC1272A RESET output is valid to VDD = 1.0V. Below this voltage, the output becomes an "open circuit" and does not sink current. This means CMOS logic inputs to the microcontroller will be floating at an undetermined voltage. Most digital systems are completely shut down well above this voltage. However, in situations where RESET must be maintained valid to VDD = 0V, a pull-down resistor must be connected from RESET to ground to discharge stray capacitances and hold the output low (Figure 3-2). This resistor value, though not critical, should be chosen such that it does not appreciably load RESET under normal operation (100 k will be suitable for most applications). 400 TA = +25°C VDD 320 VDD 240 TC1272A 160 RESET TC1272A/L/M/J 80 0 TC1272A/Z/R/S/T 1 GND R1 100 k 5 1000 100 Reset Comparator Overdrive [VTH - VDD] (mv) FIGURE 3-2: The addition of R1 at the RESET output of the TC1272A ensures that the RESET output is valid to VDD = 0V. 130 120 VDD to Reset Delay ( µsec) Combinations above the curve are detected as a brown-out or power-down condition. Transient immunity can be improved by adding a capacitor in close proximity to the VDD pin of the TC1272A. 110 TC1272A/L/M/J 100 90 80 70 60 50 TC1272A/Z/R/S/T 40 30 1 10 100 1000 Reset Comparator Overdrive (mV) [VTH - VDD] (mv) FIGURE 3-1: Maximum Transient Duration vs. Overdrive for Glitch Rejection at +25°C. DS21877B-page 4  2004-2012 Microchip Technology Inc. TC1272A 3.3 Controllers and Processors With Bidirectional I/O Pins Some microcontrollers have bidirectional reset pins. Depending on the current drive capability of the controller pin, an indeterminate logic level may result if there is a logic conflict. This can be avoided by adding a 4.7 k resistor in series with the output of the TC1272A (Figure 3-3). If there are other components in the system that require a reset signal, they should be buffered so as not to load the reset line. If the other components are required to follow the reset I/O of the microcontroller, the buffer should be connected as shown with the solid line. Buffer Buffered RESET To Other System Components VDD PIC® MicroMCU TC1272A 4.7 k RESET GND RESET GND FIGURE 3-3: Interfacing the TC1272A to a Bidirectional RESET I/O.  2004-2012 Microchip Technology Inc. DS21877B-page 5 TC1272A 4.0 PACKAGING INFORMATION 4.1 Package Marking Information 3-Pin SOT-23B  Part Number TC1272AZVNBTR Legend: Note: DS21877B-page 6 1 2 3 4 5 6 SOT-23 BA TC1272ARVNBTR BB TC1272ASVNBTR BC TC1272ATVNBTR BD TC1272AJVNBTR BE TC1272AMVNBTR BF TC1272ALVNBTR BG Part Number + temperature range and voltage (two-digit code) Part Number + temperature range and voltage (two-digit code) Lot ID number Year and work week Year and work week Year and work week In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information.  2004-2012 Microchip Technology Inc. TC1272A 3-Lead Plastic Small Outline Transistor (NB) (SOT-23) Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging E E1 2 B p1 n D p 1  c A   A1 L Units Dimension Limits n Number of Pins p Pitch p1 Outside lead pitch (basic) Overall Height Molded Package Thickness Standoff § Overall Width Molded Package Width Overall Length Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic A2 A A2 A1 E E1 D L  c B   MIN .035 .035 .000 .083 .047 .110 .014 0 .004 .015 0 0 INCHES* NOM 3 .038 .076 .040 .037 .002 .093 .051 .115 .018 5 .006 .017 5 5 MAX .044 .040 .004 .104 .055 .120 .022 10 .007 .020 10 10 MILLIMETERS NOM 3 0.96 1.92 0.89 1.01 0.88 0.95 0.01 0.06 2.10 2.37 1.20 1.30 2.80 2.92 0.35 0.45 0 5 0.09 0.14 0.37 0.44 0 5 0 5 MIN MAX 1.12 1.02 0.10 2.64 1.40 3.04 0.55 10 0.18 0.51 10 10 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: TO-236 Drawing No. C04-104  2004-2012 Microchip Technology Inc. DS21877B-page 7 TC1272A 4.2 Product Tape and Reel Specifications FIGURE 4-1: EMBOSSED CARRIER DIMENSIONS (8, 12, 16, AND 24 MM TAPE ONLY) Top Cover Tape A0 W B0 K0 P TABLE 1: CARRIER TAPE/CAVITY DIMENSIONS Case Outline Carrier Dimensions Package Type NB SOT-23 W mm P mm A0 mm B0 mm K0 mm 8 4 3.15 2.77 1.22 Output Quantity Units Reel Diameter in mm 3000 180 3-LEAD SOT-23 DEVICE TAPE AND REEL SPECIFICATIONS Device Marking FIGURE 4-2: 3L Cavity Dimensions User Direction of Feed Device Marking Pin 1 W, Width of Carrier Tape Pin 1 P, Pitch Standard Reel Component Orientation DS21877B-page 8 Reverse Reel Component Orientation  2004-2012 Microchip Technology Inc. TC1272A 5.0 REVISION HISTORY Revision B (January 2013) Added a note to each package outline drawing.  2004-2012 Microchip Technology Inc. DS21877B-page 9 TC1272A NOTES: DS21877B-page 10  2004-2012 Microchip Technology Inc. TC1272A PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X X XXXXX Device VDD Temperature Range Package Reset Threshold Device: TC1272A: Supervisor circuit with active-low RESET output VDD Reset Threshold: L M J T S R Z = = = = = = = 4.63V 4.38V 4.00V 3.08V 2.93V 2.63V 2.32V Temperature Range: V Package: NBTR = SOT-23B, 3-pin (Tape and Reel) Examples: a) TC1272AZVNBTR: Supervisor w/2.32 VDD option. b) TC1272ARVNBTR: Supervisor w/2.63 VDD option. c) TC1272ASVNBTR: Supervisor w/2.93 VDD option. d) TC1272ATVNBTR: Supervisor w/3.08 VDD option. e) TC1272AJVNBTR: Supervisor w/4.00 VDD option. f) TC1272AMVNBTR: Supervisor w/4.38 VDD g) TC1272ALVNBTR: option. Supervisor w/4.63 VDD option. = -40°C to +125°C Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. Your local Microchip sales office The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.  2004-2012 Microchip Technology Inc. DS21877B-page 11 TC1272A NOTES: DS21877B-page 12  2004-2012 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. & KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2004-2012, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620769041 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 ==  2004-2012 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS21877B-page 13 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS21877B-page 14 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 11/29/12  2004-2012 Microchip Technology Inc.