UPP1002E3/TR13

UPP1001e3, UPP1002e3, UPP1004e3 Compliant Powermite Package Commercial Two-Way Radio Antenna Switch Diode DESCRIPTION With high isolation, low loss, and low distortion characteristics, this Microsemi Powermite PIN diode is perfect for two-way radio antenna switch applications where size and power handling capability are critical. Its advantages also include the low forward bias resistance and high zero bias impedance that are essential for low loss, high isolation and wide bandwidth antenna switch performance. The Powermite package's full metallic bottom eliminates the possibility of solder flux entrapment during assembly, and its unique locking tab acts as an integral heat sink. Its innovative design makes this device ideal for use with automatic insertion equipment. DO-216 Package Important: For the latest information, visit our website http://www.microsemi.com. FEATURES  High power surface mount package with very low thermal resistance.  Specified low distortion.  Low bias current requirements.  High zero bias impedance.  Full metallic bottom eliminates flux entrapment.  Integral heat sink/locking tabs.  RoHS compliant. APPLICATIONS / BENEFITS        Two-way radio antenna switch. Low forward bias resistance. High zero bias resistance. Low loss high isolation for wide bandwidth performance. Small size DO-216 package. Compatible with automatic insertion equipment. Very low inductance and capacitance. MAXIMUM RATINGS Parameters/Test Conditions Junction and Storage Temperature Thermal Resistance Junction-to-Tab 1 Thermal Resistance Junction-to-Case (1) Steady-State Power Dissipation @ TTAB1 = 75 ºC UPP1001e3 Reverse Voltage @ IR = 10 A UPP1002e3 UPP1004e3 Solder Temperature @ 10 s Symbol Value Unit TJ and TSTG RӨJL RӨJC PD VR -55 to +150 30 10 2.5 100 200 400 260 ºC ºC/W ºC/W W V TSP Notes: 1. When mounted on a PC board with 2 oz copper. RF01104, Rev. B (8/21/15) ©2015 Microsemi Corporation o C MSC – Lawrence 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 (978) 620-2600 Fax: (978) 689-0803 MSC – Ireland Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Website: www.microsemi.com Page 1 of 5 UPP1001e3, UPP1002e3, UPP1004e3 MECHANICAL and PACKAGING        CASE: Void-free transfer molded thermosetting epoxy compound meeting UL94V-0. TERMINALS: Annealed matte-tin over copper and readily solderable per MIL-STD-750, method 2026. MARKING: P11• for UPP1001, P02• for UPP1002, and P04• for UPP1004 (dot indicates “e3” designation). POLARITY: Cathode designated by TAB 2. TAPE & REEL option: 16 mm tape per standard EIA-481-B. Consult factory for quantities. WEIGHT: Approximately 0.016 gram. See Package Dimensions on last page. PART NOMENCLATURE UPP 1001 e3 Powermite PIN diode RoHS Compliant Series Number SYMBOLS & DEFINITIONS Definition Symbol f IR IF Frequency Reverse current Forward current ELECTRICAL CHARACTERISTICS @ TA = +25 ºC unless otherwise noted Series Resistance RS @ f = 100 MHz IF = 10 mA (see Figure 1) Series Resistance RS @ f = 100 MHz IF = 50 mA Capacitance CT @ f = 1 MHz VR = 0 V (see Figure 2) Ohms Ohms TYP MAX TYP MAX MIN TYP MIN TYP TYP MAX TYP MAX 0.35 1.2 1.6 5 8 2.0 3.5 0.1 10 0.75 1.0 TYP MAX 0.75 1.0 RF01104, Rev. B (8/21/15) 0.45 Parallel Resistance RP @ f = 100 MHz V=0V (see Figure 3) pF Carrier Lifetime  @ IF = 10 mA Reverse Current IR @ VR S KOhms ©2015 Microsemi Corporation A Forward Voltage VF @ IF = 50 mA (see Figure 4) Volts Page 2 of 5 UPP1001e3, UPP1002e3, UPP1004e3 RS @ 100 MHz (Ohms) GRAPHS IF (mA) Ct @ 1 MHz (pF) FIGURE 1 - SERIES RESISTANCE (TYPICAL) VR (Volts) FIGURE 2 – CAPACITANCE (TYPICAL) RF01104, Rev. B (8/21/15) ©2015 Microsemi Corporation Page 3 of 5 UPP1001e3, UPP1002e3, UPP1004e3 Rp @ 100 MHz (Kohms) GRAPHS (continued) VR (Volts) IF (Amperes) FIGURE 3 – PARALLEL RESISTANCE (TYPICAL) VF (Volts) FIGURE 4 – FORWARD CURRENT vs FORWARD VOLTAGE (TYPICAL) RF01104, Rev. B (8/21/15) ©2015 Microsemi Corporation Page 4 of 5 UPP1001e3, UPP1002e3, UPP1004e3 PACKAGE DIMENSIONS Ltr A B C D E F G H J K Dimensions Inch Millimeters Min Max Min Max 0.029 0.039 0.73 0.99 0.016 0.026 0.40 0.66 0.070 0.080 1.77 2.03 0.087 0.097 2.21 2.46 0.020 0.030 0.50 0.76 0.051 0.061 1.29 1.54 0.021 0.031 0.53 0.78 0.004 0.008 0.10 0.20 0.070 0.080 1.77 2.03 0.035 0.045 0.89 1.14 MOUNTING PAD DIMENSIONS Ltr A B C D E RF01104, Rev. B (8/21/15) ©2015 Microsemi Corporation Dimensions Inch Millimeters 0.100 2.54 0.105 2.67 0.050 1.27 0.030 0.76 0.025 0.64 Page 5 of 5