USB2602-NU-02

USB2601/USB2602 4th Generation USB 2.0 Flash Media Controller with Integrated Card Power FETs & HS Hub Hub Controller • Provides Three USB 2.0 Downstream Ports via internal USB 2.0 Hub - Multi Transaction Translator for FS/LS devices attached • Flash Media Controller • Complete System Solution for interfacing SmartMediaTM (SM) or xD Picture CardTM (xD)1, Memory StickTM (MS), High Speed Memory Stick (HSMS), Memory Stick PRO (MSPRO), MS DuoTM, Secure Digital (SD), Mini-Secure Digital (Mini-SD), TransFlash (SD), MultiMediaCardTM (MMC), Reduced Size MultiMediaCard (RSMMC), NAND Flash, Compact FlashTM (CF) and CF UltraTM I & II, and CF form-factor ATA hard drives to USB 2.0 bus - Supports USB Bulk Only Mass Storage Compliant Bootable BIOS • Support for simultaneous operation of all above devices. (only one at a time of each of the following groups supported: CF or ATA drive, SM or XD or NAND, SD or MMC) • On-Chip 4-Bit High Speed Memory Stick and MS PRO Hardware Circuitry • On-Chip firmware reads and writes High Speed Memory Stick and MS PRO • 1-bit ECC correction performed in hardware for maximum efficiency • Hardware support for SD Security Command Extensions • 3.3 Volt I/O with 5V input tolerance on VBUS, Port Power and Over-Current Sense pins • On-chip power FETs for supplying flash media card power with minimum board components • 8051 8 bit microprocessor - Provides low speed control functions - 30 MHz execution speed at 4 cycles per instruction average - 12K Bytes of internal SRAM for general purpose scratchpad - 768 Bytes of internal SRAM for general purpose scratchpad or program execution while re-flashing external ROM • • • • • • • • • - Double Buffered Bulk Endpoint - Bi-directional 512 Byte Buffer for Bulk Endpoint - 64 Byte RX Control Endpoint Buffer - 64 Byte TX Control Endpoint Buffer Internal Program Memory Interface - 64K Byte Internal Code Space On Board 24MHz Crystal Driver Circuit Can be clocked by an external 24MHz source On-Chip 1.8V Regulator for Low Power Core Operation Internal PLL for 480MHz USB 2.0 Sampling, Configurable MCU clock 11 GPIOs for special function use: LED indicators, button inputs, power control to memory devices, etc. - Inputs capable of generating interrupts with either edge sensitivity Configuration of Hub and Flash Media features controlled either by internal defaults or via single external EEPROM. User configurable features: - Full or Partial Card compliance checking - LUN configuration and assignment - Write Protect Polarity - Cover Switch operation for xD compliance - Inquiry Command operation - SD Write Protect operation - Older CF card support - Force USB 1.1 reporting - Internal or External Power FET operation Compatible with Microsoft WinXP, WinME, Win2K SP3&4, Apple OS10 and Linux Multi-LUN Mass Storage Class Drivers Win2K, Win98/98SE and Apple OS8.6 and OS9 Multi-LUN Mass Storage Class Drivers are available from Microchip 128-Pin TQFP Package (1.0mm height, 14mm x14mm footprint); RoHS compliant package also available 1.xD Picture Card not applicable to USB2601  2004 - 2016 Microchip Technology Inc. DS00002119A-page 1 USB2601/USB2602 TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include -literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products. DS00002119A-page 2  2004 - 2016 Microchip Technology Inc. USB2601/USB2602 Table of Contents 1.0 Introduction ..................................................................................................................................................................................... 4 2.0 Pin Table ......................................................................................................................................................................................... 6 3.0 Pin Configuration ............................................................................................................................................................................ 9 4.0 Block Diagram ............................................................................................................................................................................... 10 5.0 Pin Descriptions ............................................................................................................................................................................ 11 6.0 DC Parameters ............................................................................................................................................................................. 17 7.0 Package Information ..................................................................................................................................................................... 23 8.0 GPIO Usage .................................................................................................................................................................................. 25 Appendix A: Data Sheet Revision History ........................................................................................................................................... 26 The Microchip Web Site ...................................................................................................................................................................... 27 Customer Change Notification Service ............................................................................................................................................... 27 Customer Support ............................................................................................................................................................................... 27 Product Identification System ............................................................................................................................................................. 28  2004 - 2016 Microchip Technology Inc. DS00002119A-page 3 USB2601/USB2602 1.0 INTRODUCTION The USB2601/USB2602 is an Integrated “combo” High-Speed USB hub and Flash Media Controller. The Flash media controller permanently resides on Port 1 of the Integrated USB hub. 1.1 High-Speed Hub The integrated Microchip Hub is fully compliant with the USB 2.0 Specification and will attach to a USB host as a FullSpeed Hub or as a Full-/High-Speed Hub. The Hub supports Low-Speed, Full-Speed, and High-Speed (if operating as a High-Speed Hub) downstream devices on all of the enabled downstream ports. A dedicated Transaction Translator (TT) is available for each downstream facing port. This architecture ensures maximum USB throughput for each connected device when operating with mixed-speed peripherals. The Hub works with an external USB power distribution switch device to control VBUS switching to downstream ports, and to limit current and sense over-current conditions. All required resistors on the USB ports are integrated into the Hub. This includes all series termination resistors on D+ and D– pins and all required pull-down and pull-up resistors on D+ and D– pins. The over-current sense inputs for the downstream facing ports have internal pull-up resistors. Throughout this document the upstream facing port of the hub will be referred to as the upstream port, and the downstream facing ports will be called the downstream ports. Three externally available ports are available for general USB device connectivity. 1.2 Flash Media Controller The Bulk Only Mass Storage Class Peripheral Controller intended for supporting CompactFlash (CF and CF Ultra I/II) in True IDE Mode only, SmartMedia (SM) and xD cards, Memory Stick (MS), Memory Stick DUO (MSDUO) and Memory Stick Pro (MSPRO), Secure Digital (SD), and MultiMediaCard (MMC) flash memory devices. It provides a single chip solution for the most popular flash memory cards in the market. The device consists of buffers, Fast 8051 microprocessor with expanded scratchpad, and program SRAM, and CF, MS, SM and SD controllers. The SD controller supports both SD and MMC devices. SM controller supports both SM and xD cards. 12K bytes of scratchpad SRAM and 768 Bytes of program SRAM are also provided. Eleven GPIO pins are provided for indicators, external serial EEPROM for OEM ID and system configuration information, and other special functions. Internal power FETs are provided to directly supply power to the xD/SM, MMC/SD and MS/MSPro cards. The internal ROM program is capable of implementing any combination of single or multi-LUN CF/SD/MMC/SM/MS reader functions with individual card power control and activity indication. Microchip also provides licenses** for Win98 and Win2K drivers and setup utilities. Note: Please check with Microchip for precise features and capabilities for the current ROM code release. 1.3 Acronyms SM: SmartMedia SMC: SmartMedia Controller FM: Flash Media FMC: Flash Media Controller CF: CompactFlash CFC: CompactFlash Controller SD: Secure Digital SDC: Secure Digital Controller MMC: MultiMediaCard MS: Memory Stick MSC: Memory Stick Controller TPC: Transport Protocol Code. DS00002119A-page 4  2004 - 2016 Microchip Technology Inc. USB2601/USB2602 ECC: Error Checking and Correcting CRC: Cyclic Redundancy Checking 1.4 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Reference Documents SmartMediaTM Electrical Specification Version 1.30 SmartMediaTM Physical Format Specifications Version 1.30 SmartMediaTM Logical Format Specifications Version 1.20 SMIL (SmartMedia Interface Library) Software Edition Version 1.00, Toshiba Corporation, 01, July, 2000 SMIL (SmartMedia Interface Library) Hardware Edition Version 1.00, Toshiba Corporation, 01, July, 2000 MultiMediaCard System Specification Version 2.2 SD Memory Card Specifications, Part 1, Physical Layer Specification Version 1.10, April 2003, SD Group SD Memory Card Specifications, Part 2, File System Specification Version 1.01, April 15th, 2001, SD Group SD Memory Card Specifications, Part 3, Security Specification Version 1.01, April 15th, 2001, SD Group SD Card Specification, Part E1, Secure Digital Input/Output (SDIO) card Specification, Version 1.00, October 2001, SD Group Memory Stick Standard Excerpt from Format Specification v1.3, July, 2000, Sony Corporation. Memory Stick Standard Format Specifications Version 2.0 (Memory Stick PRO) Tentative Release 0.81, February, 2002 CompactFlash Specification Rev. 1.4 CF+ & CF Specification Rev. ATA-5 Draft 0.2 Universal Serial Bus Specification Rev. 2.0 Samsung K9K2G08Q0M Data Sheet xD Picture Card, Card Specification Version 1.10 (Jan 31, 2004) xD Picture Card, Format Specification Version 1.10 (Jan 31, 2004) xD Picture Card, Host Guideline Version 1.10 (Jan 31, 2004) xD Picture Card, Compliance Guideline Version 1.10 (Jan 31, 2004)  2004 - 2016 Microchip Technology Inc. DS00002119A-page 5 USB2601/USB2602 2.0 PIN TABLE 2.1 128-Pin TQFP Package TABLE 2-1: USB2601/USB2602 128-PIN TQFP PACKAGE UPSTREAM USB 2.0 INTERFACE (3 PINS) USBUP_DP USBUP_DM VBUS_DET 3-PORT USB 2.0 INTERFACE (16 PINS) USBDN_DP2 USBDN_DM2 USBDN_DP3 USBDN_DM3 USBDN_DP4 USBDN_DM4 PRTPWR2 PRTPWR3 PRTPWR4 OCS2_N OCS3_N OCS4_N GR3_N GR4_N PRTPWR_POL GR2_N CompactFlash INTERFACE (28 Pins) CF_D0 CF_D1 CF_D2 CF_D3 CF_D4 CF_D5 CF_D6 CF_D7 CF_D8 CF_D9 CF_D10 CF_D11 CF_D12 CF_D13 CF_D14 CF_D15 CF_nIOR CF_nIOW CF_IRQ CF_nRESET CF_IORDY CF_nCS0 CF_nCS1 CF_SA0 CF_SA2 CF_nCD1 CF_nCD2 CF_SA1 SmartMedia INTERFACE (17 Pins) SM_D0 SM_D1 SM_D2 SM_D3 SM_D4 SM_D5 SM_D6 SM_D7 SM_ALE SM_CLE SM_nRE SM_nWE SM_nWP SM_nB/R SM_nCE SM_nCD SM_nWPS Memory Stick INTERFACE (7 Pins) MS_BS MS_SDIO/MS_D0 MS_SCLK MS_D1 MS_D2 MS_D3 SD_CMD SD_CLK SD_DAT2 SD_DAT3 MS_INS SD INTERFACE (7 Pins) SD_DAT0 SD_DAT1 SD_nWP MISC (23 Pins) GPIO1 GPIO2 GPIO4 GPIO5 GPIO6 GPIO7 GPIO8/CRD_PWR0 GPIO9 GPIO10/CRD_PWR1 GPIO11/CRD_PWR2 GPIO12 GPIO13 GPIO14 GPIO15 TEST RESET_N XTAL2 ATEST RBIAS XTAL1/CLKIN CLK_SEL0 CLK_SEL1 SEL_CLKDRV (3)VDDA33 VDD33PLL ANALOG POWER (5 Pins) VDD18PLL DIGITAL, POWER & GROUND (22 Pins) (5)VDD33 (11)VSS (3)VDD18 (3)NC Total 128 DS00002119A-page 6  2004 - 2016 Microchip Technology Inc. USB2601/USB2602 2.2 128-Pin List Table TABLE 2-2: Pin # USB2601/USB2602 128-PIN TQFP Name MA Pin # Name MA Pin # Name MA Pin # Name MA 1 PRTPWR_P OL - 33 VDD18 - 65 CF_D7 8 97 SD_nWP - 2 PRTPWR2 12 34 VSS - 66 CF_D15 8 98 SD_DAT1 8 3 OCS2_N - 35 VSS - 67 CF_nCS0 8 99 SD_DAT0 8 4 PRTPWR3 12 36 SM_nWPS - 68 CF_nCS1 8 100 SD_CLK 8 5 OCS3_N - 37 SM_CLE 8 69 CF_nIOR 8 101 VDD33 - 6 PRTPWR4 12 38 SM_nCE 8 70 CF_nIOW 8 102 GPIO11/ CRD_PWR2 - 7 OCS4_N - 39 SM_ALE 8 71 CF_IRQ 8 103 SD_CMD 8 8 VDDA33 - 40 SM_nRE 8 72 CF_nRESET 8 104 SD_DAT3 8 9 USBDN_DP 3 -- 41 SM_nWE 8 73 CF_IORDY 8 105 SD_DAT2 8 10 USBDN_DM 3 - 42 SM_nB/R - 74 CF_SA2 8 106 GPIO4 8 11 VSS - 43 VDD33 - 75 CF_SA1 8 107 GPIO5 8 12 USBDN_DM 4 - 44 GPIO10/ CRD_PWR1 - 76 CF_SA0 8 108 VSS - 13 USBDN_DP 4 - 45 SM_nWP 8 77 CF_D0 8 109 VSS - 14 VDDA33 - 46 SM_D0 8 78 CF_D1 8 110 USBUP_DM - 15 VDD33 - 47 SM_D1 8 79 CF_D8 8 111 USBUP_DP - 16 GR2_N 8 48 SM_D7 8 80 CF_D2 8 112 VDDA33 - 17 GR3_N 8 49 SM_D2 8 81 CF_D9 8 113 USBDN_DP2 - 18 GR4_N 8 50 SM_D6 8 82 CF_D10 8 114 USBDN_DM2 - 19 GPIO6 8 51 SM_D3 8 83 CF_nCD2 - 115 VSS - 20 MS_BS 8 52 SM_D5 8 84 VSS - 116 VBUS_ DET 12 21 MS_D1 8 53 SM_D4 8 85 VSS - 117 VSS - 22 MS_SDIO/M S_D0 8 54 SM_nCD - 86 VDD18 - 118 RESET_N - 23 MS_D2 8 55 GPIO9 8 87 VDD33 - 119 VDD18 - 24 MS_INS - 56 CF_nCD1 - 88 GPIO1 8 120 TEST - 25 MS_D3 8 57 CF_D3 8 89 GPIO2 8 121 VSS - 26 MS_ SCLK 8 58 CF_D11 8 90 GPIO7 8 122 XTAL2 - 27 SEL_CLKDR V - 59 CF_D4 8 91 VDD33 - 123 XTAL1/ CLKIN - 28 CLK_SEL1 - 60 CF_D12 8 92 GPIO8/ CRD_PWR0 - 124 VDD18PLL - 29 CLK_SEL0 - 61 CF_D5 8 93 GPIO12 8 125 VDD33PLL - 30 NC - 62 CF_D13 8 94 GPIO13 8 126 ATEST - 31 NC - 63 CF_D6 8 95 GPIO14 8 127 RBIAS - 32 NC - 64 CF_D14 8 96 GPIO15 8 128 VSS -  2004 - 2016 Microchip Technology Inc. DS00002119A-page 7 USB2601/USB2602 Note 1: RBIAS is connected to the Analog Ground plane VSS via a resistor. 2: When the internal 1.8V regulators are enabled, VDD18 (Pin 86) & VDD18PLL (Pin 124), MUST have a 10uf +/- 20%, (equivalent series resistance (ESR)