ZL30153GGG20037

ZL30153 Synchronous Ethernet Network Synchronization DPLL Short Form Data Sheet April 2014 Features • • Ordering Information ZL30153GGG 100 Pin LBGA ZL30153GGG2 100 Pin LBGA* Supports requirements of ITU-T G.8262 for Synchronous Ethernet Equipment Slave Clocks (EEC option 1 and 2) Trays Trays *Pb Free Tin/Silver/Copper -40oC to +85oC Supports requirements of Telcordia GR-1244 Stratum 3 and GR-253, ITU-T G.813, and G.781 SETS 28 Hz, 56 Hz, 112 Hz, 224 Hz, 448 Hz or 896 Hz • Supports ITU-T G.823, G.824 and G.8261 for 2048 kbit/s and 1544 kbit/s interfaces • Automatic hitless reference switching and digital holdover on reference fail • Programmable synthesizers generate any clockrate from 1 Hz to 750 MHz • Four reference inputs configurable as single ended or differential • Two precision synthesizers generate clocks with low jitter of 0.7 ps RMS for 10 G PHYs • Eight LVPECL outputs and four LVCMOS outputs • Programmable digital PLL synchronize to any clock rate from 1 Hz to 750 MHz • Operates from a single crystal resonator or clock oscillator • Flexible two-stage architecture translates between arbitrary data rates, line coding rates and FEC rates • Configurable via SPI/I2C interface • Digital PLL filter jitter from 0.1 mHz, 1 mHz, 10 mHz, 0.1 Hz, 1.7 Hz, 3.6 Hz, 7 Hz, 14 Hz, Figure 1 - Functional Block Diagram 1 Microsemi Corporation Copyright 2014, Microsemi Corporation. All Rights Reserved. ZL30153 Applications • 10 Gigabit line cards • Synchronous Ethernet, 10GBASE-R and 10GBASE-W • OTN multiplexers and transponders • SONET/SDH, Fibre Channel, XAUI 2 Microsemi Corporation Short Form Data Sheet ZL30153 Mechanical Drawing 3 Microsemi Corporation Short Form Data Sheet For more information about all Microsemi products visit our Web Site at www.microsemi.com Information relating to products and services furnished herein by Microsemi Corporation or its subsidiaries (collectively “Microsemi”) is believed to be reliable. However, Microsemi assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Microsemi or licensed from third parties by Microsemi, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Microsemi, or non-Microsemi furnished goods or services may infringe patents or other intellectual property rights owned by Microsemi. This publication is issued to provide information only and (unless agreed by Microsemi in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Microsemi without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Microsemi’s conditions of sale which are available on request. Purchase of Microsemi’s I2C components conveys a license under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Microsemi, ZL, the Microsemi Corporation logo and the Legerity logo and combinations thereof, VoiceEdge, VoicePort, SLAC, ISLIC, ISLAC and VoicePath are trademarks of Microsemi Corporation. TECHNICAL DOCUMENTATION - NOT FOR RESALE