ZL30161GDG2003V

ZL30161 Network Synchronization Clock Translator Short Form Data Sheet May 2013 Features • Ordering Information ZL30161GDG2 144 Pin LBGA Trays Fully compliant SEC (G.813) and EEC (G.8262) flexible rate conversion digital phase locked loop (DPLL) Pb Free Tin/Silver/Copper -40oC to +85oC Package Size: 13 x 13 mm • Programmable DPLL/Numerically Controlled Oscillators (NCO) • Synchronizes to any clock rate from 1 Hz to 750 MHz • Any input reference can be fed with sync (frame pulse) or clock • Three programmable synthesizers generate any clock rate from 1 Hz to 750 MHz with maximum jitter below 0.62 ps rms • Programmable DPLL can synchronize to sync pulse and sync/clock pair. • Six LVPECL outputs and six LVCMOS outputs • Operates from a single crystal resonator or clock oscillator • Field programmable via SPI/I 2C interface • Flexible two-stage architecture translates between arbitrary data rates, line coding rates and FEC rates • Digital PLL filters jitter from 0.1 mHz up to 1 kHz • Automatic hitless reference switching and digital holdover on reference fail Applications • Nine input references configurable as single ended or differential and two single ended input references • SyncE/SONET/SDH Timing Cards • Synchronous Ethernet, 10 GBASE-R and 10 GBASE-W • SONET/SDH, Fibre Channel, XAUI Osci Osco ZL30161 Master Clock Ref0 Diff / Single Ended Fr0= Br0*Kr0*Mr0/Nr0 Ref1 Diff / Single Ended Fr1= Br1*Kr1*Mr1/Nr1 Ref2 Diff / Single Ended Fr2= Br2*Kr2*Mr2/Nr2 Ref3 Diff / Single Ended Fr3= Br3*Kr3*Mr3/Nr3 Ref4 Diff / Single Ended Fr4= Br4*Kr4*Mr4/Nr4 Ref5 Diff / Single Ended Fr5= Br5*Kr5*Mr5/Nr5 Ref6 Diff / Single Ended Fr6= Br6*Kr6*Mr6/Nr6 Ref7 Diff / Single Ended Fr7= Br7*Kr7*Mr7/Nr7 Ref8 Diff / Single Ended Fr8= Br8*Kr8*Mr8/Nr8 Ref9 Single Ended Fr9= Br9*Kr9*Mr9/Nr9 Ref10 Single Ended Fr10= Br10*Kr10*Mr10/Nr10 Clock Generator 0 Synthesizer 0 Fs= Bs0*Ks0*16*Ms0/Ns0 Clock Generator 1 DPLL/NCO Select Loop band., Phase slope limit Synthesizer 1 Fs= Bs1*Ks1*16*Ms1/Ns1 Clock Generator 2 Synthesizer 2 Fs= Bs2*Ks2*16*Ms2/Ns2 State Machine JTAG Reference Monitors JTAG pwr_b Div A LVPECL Div B LVPECL Div C LVCMOS hpoutclk0 Div D LVCMOS hpoutclk1 Div A LVPECL hpdiff2_p/n Div B LVPECL hpdiff3_p/n Div C LVCMOS hpoutclk2 Div D LVCMOS hpoutclk3 Div A LVPECL hpdiff4_p/n Div B LVPECL hpdiff5_p/n Div C LVCMOS hpoutclk4 Div D LVCMOS hpoutclk5 Configuration and Status GPIO SPI / I2C Figure 1 - Functional Block Diagram 1 Copyright 2013, Microsemi Corporation. All Rights Reserved. hpdiff0_p/n hpdiff1_p/n ZL30161 1.0 Short Form Data Sheet Pin Diagram TOP VIEW 1 2 3 4 hpdiff0_p VDD0 NC VDD1 hpdiff0_n VSS NC hpdiff1_p hpdiff1_n VDD7 5 6 7 8 osco_1V8 VDD2 osco_3V3 osci_3V3 VSS osci_1V8 VSS XOin VDD5 VSS VSS VCORE1 VSS hpoutclk0 hpoutclk1 VSS VDD9 VDD10 VSS 9 10 11 VDD3 NC VDD4 VCORE0 VSS NC VSS VSS VSS VSS VDD6 VSS VSS VSS hpoutclk3 hpoutclk2 VSS VDD8 VSS VSS VSS VSS VSS VDD11 IC1 NC 12 A hpdiff2_p B hpdiff2_n C hpdiff3_n hpdiff3_p D E NC F NC trst_b hpoutclk4 hpoutclk5 VSS VSS VSS VSS NC NC pwr_b NC tdi tdo tms VSS VSS VSS VSS VSS VDD12 gpio1 gpio0 IC2 hpdiff4_p hpdiff4_n tck VSS VSS VSS VSS VSS VCORE2 gpio2 NC NC VSS gpio4 VSS VSS VSS VSS VSS VCORE3 gpio3 VSS VDD14 hpdiff5_n gpio5 gpio6 VSS VCORE4 cs_b_asel0 sck_scl si_sda so_asel1 NC NC G H J VDD13 K hpdiff5_p L VDD15 VSS ref1_p ref1_n ref3_p ref3_n ref5_p ref5_n ref6_n ref8_p ref8_n ref10 VCORE5 VSS ref0_p ref0_n ref2_p ref2_n ref4_p ref4_n ref6_p ref7_p ref7_n ref9 M 1 - A1 corner is identified by metallized markings. Figure 2 - Pin Diagram 2 Microsemi Corporation ZL30161 2.0 Short Form Data Sheet Pin Description All device inputs and outputs are LVCMOS unless it is specifically stated to be differential. For the I/O column, there are digital inputs (I), digital outputs (O), analog inputs (A-I) and analog outputs (A-O). Ball # Name I/O Description M3 M4 L3 L4 M5 M6 L5 L6 M7 M8 L7 L8 M9 L9 M10 M11 L10 L11 ref0_p ref0_n ref1_p ref1_n ref2_p ref2_n ref3_p ref3_n ref4_p ref4_n ref5_p ref5_n ref6_p ref6_n ref7_p ref7_n ref8_p ref8_n I Input References 0 to 8. Input reference sources used for synchronization. The positive and negative pair of these inputs accepts a differential input signal. The refx_p input terminal accepts a CMOS input reference. These inputs can be used as an external feedback input. M12 L12 ref9 ref10 I Input Reference Maximum frequency limit on single ended inputs is 177.5 MHz, and 750 MHz on differential inputs. Input References 9 and 10. Input reference sources used for synchronization. These inputs are the same as inputs 0 to 8, but only single ended. These inputs can be used as an external feedback input. Maximum frequency limit is 177.5 MHz Output Clocks D3 D4 D10 D9 F3 F4 hpoutclk0 hpoutclk1 hpoutclk2 hpoutclk3 hpoutclk4 hpoutclk5 O A1 B1 C1 C2 A12 B12 C12 C11 H1 H2 K1 K2 hpdiff0_p hpdiff0_n hpdiff1_p hpdiff1_n hpdiff2_p hpdiff2_n hpdiff3_p hpdiff3_n hpdiff4_p hpdiff4_n hpdiff5_p hpdiff5_n O High Performance Output Clocks 0 to 5. These outputs can be configured to provide any one of the single ended high performance clock outputs. Maximum frequency limit on single ended LVCMOS outputs is 177.5 MHz. High Performance Differential Output Clocks 0 to 5 (LVPECL). These outputs can be configured to provide any one of the available high performance differential output clocks. Maximum frequency limit on differential outputs is 750 MHz. Table 1 - Pin Description 3 Microsemi Corporation ZL30161 Ball # Name Short Form Data Sheet I/O Description Power-on Reset. A logic low at this input resets the device. To ensure proper operation, the device must be reset after power-up. The pwr_b pin should be held low for 2 ms after all power supplies are stabilized. This pin is internally pulled-up to VDD. User can access device registers either 125 ms after pwr_b goes high, or after bit 7 in register at address 0x000 goes high (which can be determined by polling). Control and Status F11 pwr_b I G11 G10 H10 J10 J3 K3 K4 gpio0 gpio1 gpio2 gpio3 gpio4 gpio5 gpio6 I/O General Purpose Input and Output pins. These are general purpose I/O pins. Example GPIO functions include: • DPLL lock indicators • DPLL holdover indicators • Reference fail indicators • Reference select control or monitor • Differential output clock enable • High performance LVCMOS outputs enable • Host Interrupt Output to flag status changes. All GPIO functions are listed in section 5.2, “GPIO Configuration“. Pins 5:0 are internally pulled down to GND and pin 6 is internally pulled up to VDD. Unused GPIO pins can be left unconnected. After power on reset, device GPIO[0,1,3,4] configure basic device function. GPIO3 sets I2C or SPI control mode, GPIO[1,0] sets master clock rate selection. The GPIO[0,1,3] pins must be either pulled low or high with an external 1 kohms resistor for their assigned functions at reset; or they must be driven low or high for 125 ms after reset, and released and then used for normal GPIO functions. The GPIO4 pin must be either pulled low with an external 1 kohms resistor; or it must be driven low for 125 ms after reset, and then released and used for normal GPIO functions. GPIO[5,6] are not used during power up. Host Interface K8 sck_scl I/O Clock for Serial Interface. Provides clock for serial micro-port interface. This pin is also the serial clock line (SCL) when the host interface is configured for I2C mode. As an input this pin is internally pulled up to VDD. K9 si_sda I/O Serial Interface Input. The serial data stream holds the access command, the address and the write data bits. This pin is also the serial data line (SDA) when host interface is configured for I2C mode. This pin is internally pulled up to VDD. K10 so_asel1 I/O Serial Interface Output. As an output, the serial stream holds the read data bits. This pin is also the I2C address select when host interface is configured for I2C mode. Table 1 - Pin Description (continued) 4 Microsemi Corporation ZL30161 Short Form Data Sheet Ball # Name I/O Description K7 cs_b_asel0 I Chip Select for Serial Interface. Serial interface chip select, this is an active low signal. This pin is also the I2C address select when host interface is configured for I2C mode.This pin is internally pulled up to VDD. I Internal Connection. Connect this pin to GND. JTAG (IEEE 1149.1) and Test G12 IC2 E11 IC1 G2 tdo O Test Serial Data Out. JTAG serial data is output on this pin on the falling edge of tck. This pin is held in high impedance state when JTAG scan is not enabled. G1 tdi I Test Serial Data In. JTAG serial test instructions and data are shifted in on this pin. This pin is internally pulled up to VDD. If this pin is not used then it should be left unconnected. F2 trst_b I Test Reset. Asynchronously initializes the JTAG TAP controller by putting it in the Test-Logic-Reset state. This pin should be held low or pulsed low on power-up to ensure that the device is in the normal functional state. This pin is internally pulled up to VDD. If this pin is not used then it should be connected to GND. H3 tck I Test Clock. Provides the clock for the JTAG test logic. This pin is internally pulled up to VDD. If this pin is not used then it should be connected to GND. G3 tms I Test Mode Select. JTAG signal that controls the state transitions of the TAP controller. This pin is internally pulled up to VDD. If this pin is not used then it should be left unconnected. A-I/O Internal Connection. Leave unconnected. Master Clock Note: The osci_1V8/osco_1V8 pins are preferred to connect a crystal to the device. The XOin pin is preferred to connect a crystal oscillator (XO) to the device. A7 osco_3V3 A8 osci_3V3 A5 osco_1V8 B5 osci_1V8 A-O 3.3V Crystal Master Clock Output. For the alternative connection method for a crystal, the crystal is connected from this pin to osci_3V3. Not suitable for driving other devices. For clock oscillator operation or the use of a crystal between osci_1V8 and osco_1V8, this pin should be left unconnected. I 3.3V Crystal Master Clock Input. For the alternative connection method for a crystal, the crystal is connected from this pin to osco_3V3. For clock oscillator operation or the use of a crystal between osci_1V8 and osco_1V8, this pin should be grounded. A-O 1.8V Crystal Master Clock Output. For the primary connection method for a crystal, the crystal is connected from this pin to osci_1V8. Not suitable for driving other devices. For clock oscillator operation or the use of a crystal between osci_3V3 and osco_3V3, this pin should be left unconnected. I 1.8V Crystal Master Clock Input. For the primary connection method for a crystal, the crystal is connected from this pin to osco_1V8. For clock oscillator operation or the use of a crystal between osci_3V3 and osco_3V3, this pin should be grounded. Table 1 - Pin Description (continued) 5 Microsemi Corporation ZL30161 Ball # Name I/O B7 XOin I Short Form Data Sheet Description XO Master Clock Output. For clock oscillator operation, this pin is connected to the output of the oscillator. For crystal operation using either method, this pin should be grounded. Power and Ground B8 C6 H9 J9 K6 M1 VCORE0 VCORE1 VCORE2 VCORE3 VCORE4 VCORE5 A2 A4 A6 A9 A11 C3 C10 D1 D12 E2 E3 E10 G9 J1 J12 L1 VDD0 VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 VDD7 VDD8 VDD9 VDD10 VDD11 VDD12 VDD13 VDD14 VDD15 Positive Supply Voltage. +1.8VDC nominal. These pins should not be connected together on the board. Please refer to ZLAN-327 for recommendations Positive Supply Voltage. +3.3VDC nominal. These pins should not be connected together on the board. Please refer to ZLAN-327 for recommendations Table 1 - Pin Description (continued) 6 Microsemi Corporation ZL30161 Ball # Name B2 B4 B6 B9 B11 C4 C5 C7 C8 C9 D2 D11 E4 E9 G4 H4 H5 H6 H7 H8 J2 J4 J5 J6 J7 J8 J11 K5 L2 M2 D5 D6 D7 D8 E5 E6 E7 E8 F5 F6 F7 F8 G5 G6 G7 G8 VSS I/O Short Form Data Sheet Description Ground. 0 Volts. Table 1 - Pin Description (continued) 7 Microsemi Corporation ZL30161 Ball # Name A3 A10 B3 B10 E1 E12 F1 F9 F10 F12 H11 H12 K12 K11 NC I/O Short Form Data Sheet Description No Connect. These pins should be left open. Table 1 - Pin Description (continued) 8 Microsemi Corporation ZL30161 3.0 Mechanical Drawing 9 Microsemi Corporation Short Form Data Sheet Information relating to products and services furnished herein by Microsemi Corporation or its subsidiaries (collectively “Microsemi”) is believed to be reliable. However, Microsemi assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Microsemi or licensed from third parties by Microsemi, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Microsemi, or non-Microsemi furnished goods or services may infringe patents or other intellectual property rights owned by Microsemi. This publication is issued to provide information only and (unless agreed by Microsemi in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Microsemi without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical and other products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Microsemi’s conditions of sale which are available on request. For more information about all Microsemi products visit our website at www.microsemi.com/timing-and-synchronization TECHNICAL DOCUMENTATION – NOT FOR RESALE Microsemi Corporation (NASDAQ: MSCC) offers a comprehensive portfolio of semiconductor solutions for: aerospace, defense and security; enterprise and communications; and industrial and alternative energy markets. Products include high-performance, high-reliability analog and RF devices, mixed signal and RF integrated circuits, customizable SoCs, FPGAs, and complete subsystems. Microsemi is headquartered in Aliso Viejo, Calif. Learn more at www.microsemi.com. Microsemi Corporate Headquarters One Enterprise, Aliso Viejo CA 92656 USA Within the USA: +1 (949) 380-6100 Sales: +1 (949) 380-6136 Fax: +1 (949) 215-4996 © 2013 Microsemi Corporation. All rights reserved. Microsemi and the Microsemi logo are trademarks of Microsemi Corporation. All other trademarks and service marks are the property of their respective owners.