QPA0363ATR7

QPA0363A ® DC – 5000 MHz Cascadable SiGe HBT Amplifier Product Overview The QPA0363A is a high performance SiGe HBT MMIC amplifier. A Darlington configuration provides high FT and excellent thermal performance. The heterojunction increases breakdown voltage and minimizes leakage current between junctions. Cancellation of emitter junction non-linearities results in higher suppression of intermodulation products. The QPA0363A may be operated from a variety of supply voltages by using a voltage dropping resistor. Two DCblocking capacitors, bypass capacitors and an optional RF choke complete the circuit required for operation of this internally matched 50 ohm device. The QPA0363A is assembled in an industry standard SOT363 package that is lead-free and RoHS-compliant. 6 Lead SOT-363 Package Key Features  DC to 5000 MHz Operation  Single Positive Voltage Supply  Low Current Draw: 11 mA at +5 V Supply  Output IP3: +20 dBm typical at 1950 MHz  Noise Figure: 2.85 dB Typical at 1950 MHz  Robust 1000 V Class 1C HBM ESD Rating  Lead-free/RoHS-compliant SOT-363 Package Functional Block Diagram Applications  Cellular, PCS, GSM, UMTS  PA Driver Amplifier  IF/RF Buffer Amplifier  Wireless Data, Satellite Top View Ordering Information Part No. Description QPA0363ASQ 25 Piece Sample Bag QPA0363ASR 100 Pieces on 7” Reel QPA0363ATR7 3000 pieces on a 7” reel QPA0363APCK401 850 MHz, EVB with 5 Piece Sample Bag Data Sheet Nov. 1, 2016 | Subject to change without notice 1 of 7 www.qorvo.com QPA0363A DC – 5000 MHz Cascadable SiGe HBT Amplifier ® Absolute Maximum Ratings Parameter Storage Temp Recommended Operating Conditions Rating −55 to +150 °C Device Voltage (VD) +4 V Device Current (ID) 22 mA RF Input Power (ZL = 50 Ω) −5 dBm Parameter Min Operating Temperature −40 Junction Temperature (TJ) Typ Max Units +105 °C +125 °C Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Bias Conditions should also satisfy the following expression: ID x VD < (TJUNCTION -TLEAD) / RTH Electrical Specifications Parameter Small Signal Gain Output Power at 1dB Compression Output Third Intercept Point Conditions Min Typ 850 MHz 19.3 1950 MHz 16.9 2400 MHz 15.7 850 MHz +1.0 1950 MHz +1.7 2400 MHz +1.7 500 MHz +16.3 850 MHz +17.5 1950 MHz +20.0 2400 MHz +19.0 Max Units dB dBm dBm 3500 MHz +16.5 Input Return Loss, |S11| 1950 MHz 17.5 dB Output Return Loss, |S22| 1950 MHz 21.2 dB Reverse Isolation, |S12| 1950 MHz 20.8 dB 850 MHz 2.60 1950 MHz 2.85 Noise Figure dB Device Operating Voltage +2.5 V Device Operating Current 11 mA Thermal Resistance 123 °C/W Notes: 1. Test conditions unless otherwise noted: VS=+5 V, RBIAS = 220 Ω ID=11 mA Typ., OIP3 Tone Spacing=1 MHz, POUT per tone = -12 dBm, 50 Ω system, Temp. = +25 °C. Data Sheet Nov. 1, 2016 | Subject to change without notice 2 of 7 www.qorvo.com QPA0363A ® DC – 5000 MHz Cascadable SiGe HBT Amplifier Performance Plots  –  850 MHz Application Circuit Test conditions unless otherwise noted: VS = +5.0 V, ID = 11 mA Data Sheet Nov. 1, 2016 | Subject to change without notice 3 of 7 www.qorvo.com QPA0363A DC – 5000 MHz Cascadable SiGe HBT Amplifier ® Evaluation Board and Schematic  –  850 MHz Application Circuit Bill of Material  –  850 MHz Application Circuit Reference Description Manufacturer Part Number n/a n/a Value PCB Qorvo QPAXX63X-410(A) U1 n/a HBT MMIC Amplifier Qorvo QPA0363A C1 1 uF CAP, 10%, 25V, X7R, 1206 Murata Electronics GRM31MR71E105KA01L C2 1000 pF CAP, 10%, 50V, X7R, 0402 Murata Electronics GRM155R71H102KA01D C3 68 pF CAP, 5%, 50V, C0G, 0402 Murata Electronics GRM1555C1H680JA01D C4, C5 100 pF CAP, 5%, 50V, C0G, 0402 Murata Electronics GRM1555C1H101JA01D R1 220 Ω RES, 220 Ω, 5%, 1/2W, 1210 Panasonic Industrial Devices ERJ-14YJ221U L1 33 nH IND, 5%, M/L, 0603 Murata Electronics LL1608-FSL33NJ J1, J2 n/a CONN, SMA, EL, FLT, 0.068" SPE-000318 Amphenol RF Asia Corp 901-10426 P1 n/a CONN, HDR, ST, 1x2, 0.100", Hi-temp, T/H Samtec Inc HTSW-102-07-G-S Component Values for Specific Frequencies Reference Designator 500 MHz 850 MHz 1950 MHz 2400 MHz 3500 MHz C4, C5 220 pF 100 pF 68 pF 56 pF 39 pF C3 100 pF 68 pF 22 pF 22 pF 15 pF L1 68 nH 33 nH 22 nH 18 nH 15 nH Bias Resistor Values for Specific Supply Voltages Reference Designator R1 ( Rbias) (1, 2) VS=+5 V VS=+7.5 V VS=+9 V VS=+12 V 220 Ω 470 Ω 620 Ω 910 Ω Notes: 1. Bias resistor improves current stability over temperature 2. Bias Resistance = RBIAS + RLDC = ( VS -VD ) / ID Data Sheet Nov. 1, 2016 | Subject to change without notice 4 of 7 www.qorvo.com QPA0363A DC – 5000 MHz Cascadable SiGe HBT Amplifier ® Pin Configuration and Description Top View Pad No. Label Description 1, 2, 4, 5 GND Connection to ground. Use via holes in PCB for best performance to reduce lead inductance as close to ground leads as possible 3 RFIN RF Input Pin. DC voltage is present on this pin therefore this pin requires the use of an external DC blocking capacitor chosen for the frequency of operation. 6 RFOUT/Bias RF Output and Bias Pin. DC voltage is present on this pin therefore this pin requires the use of an external DC blocking capacitor chosen for the frequency of operation. Package Marking XXXX is an Alpha-numeric trace code. Data Sheet Nov. 1, 2016 | Subject to change without notice 5 of 7 www.qorvo.com QPA0363A ® DC – 5000 MHz Cascadable SiGe HBT Amplifier Package Dimensions Notes: 1. All dimensions are in inches (millimeters). Angles are in degrees. 2. Dimension and tolerance formats conform to ASME Y14.5-2009. PCB Mounting Pattern Data Sheet Nov. 1, 2016 | Subject to change without notice 6 of 7 www.qorvo.com QPA0363A DC – 5000 MHz Cascadable SiGe HBT Amplifier ® Handling Precautions Parameter Rating Standard ESD – Human Body Model (HBM) Class 1C ESDA / JEDEC JS-001-2014 ESD – Charged Device Model (CDM) Class C3 ESDA / JEDEC JS-002-2014 MSL – Moisture Sensitivity Level Level 1 IPC/JEDEC J-STD-020 Caution! ESD-Sensitive Device Solderability Compatible with lead-free (260°C max. reflow temp.) soldering process. Solder profiles available upon request. Contact plating: Matte Sn RoHS Compliance This part is compliant with 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment) as amended by Directive 2015/863/EU. This product also has the following attributes:  Lead Free  Halogen Free (Chlorine, Bromine)  Antimony Free  TBBP-A (C15H12Br402) Free  PFOS Free  SVHC Free Pb Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations: Web: www.qorvo.com Tel: 1-844-890-8163 Email: customer.support@qorvo.com For technical questions and application information: Email: sjcapplications.engineering@qorvo.com Important Notice The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Copyright 2016 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc. Data Sheet Nov. 1, 2016 | Subject to change without notice 7 of 7 www.qorvo.com