HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Typical Applications
Features
The HMC699LP5(E) is ideal for:
Ultra Low SSB Phase Noise Floor:
-153 dBc/Hz @ 10 kHz offset @ 100 MHz
Reference Frequency.
• Satellite Communication Systems
• Point-to-Point Radios
Programmable Divider (N = 16 - 519)
Operating up to 7 GHz
• Military Applications
• Sonet Clock Generation
PLL - INTEGER-n synthesizer - SMT
6
Open Collector Output Buffer Amplifiers for
Interfacing w/ Op-Amp Based Loop Filter
Reversible Polarity PFD w/ Lock Detect Output
32 Lead 5x5mm SMT Package: 25mm2
Functional Diagram
General Description
The HMC699LP5(E) is a frequency synthesizer with
a wideband reversible polarity digital PFD and lock
detect output. The divider operates from 160 - 7000
MHz with a continuous integer division ratio N = 56
to 519 and non-continuous division ratio N = 16 to
54. The HMC699LP5(E) high frequency operation
along with ultra low phase noise floor make possible
synthesizers with wide loop bandwidth and low N
resulting in fast settling and very low phase noise.
When used in conjunction with a differential loop
filter, the HMC699LP5(E) can be used to phase
lock a VCO to a reference oscillator. For continuous
division ratio, the A counter and S counter must
satisfy the condition: A + 1 ≥ S.
Electrical Specifications, TA = +25° C, Vcc = Vcc1 = Vcc2 = Vcc3 = Vcc_pd = 5V
Conditions
Min.
Maximum Ref. Input Frequency
Parameter
Sine or Square Wave Input [1]
1300
Minimum Ref. Input Frequency
Square Wave Input [2]
Reference Input Power Range
100 MHz Frequency
Maximum VCO Input Frequency
Minimum VCO Input Frequency
VCO Input Power Range
SSB Phase Noise
Max.
MHz
-5
MHz
+5
dBm
MHz
Sine Wave Input
100 MHz Input Frequency
Units
10
7000
PFD Output Voltage
PFD Gain
Typ.
-10
160
MHz
+5
dBm
2000
mV, Pk - Pk
Gain = Vpp / 2π Rad.
0.32
V/Rad.
@ 10 kHz Offset @ 100 MHz Square Wave Ref. Input
Pin= 0 dBm
-153
dBc/Hz
345
mA
Total Supply Current
[1] Maximum frequencies may be limited by available counter division ratio.
[2] Square wave input achieves best phase noise at lower reference frequency (see sine & square wave comparison plots)
6-1
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Phase Noise Floor [1][2][3]
Ref = Sine Wave, Vcc = 4.75V
Phase Noise Floor [1][2][3]
Ref = Square Wave, Vcc = 4.75V
-100
-10 dBm
-5 dBm
0 dBm
+5 dBm
-120
-130
-140
-150
-160
-170
-180
2
10
-110
-120
-130
-140
-150
-160
-170
3
4
10
10
-180
2
10
5
10
OFFSET FREQUENCY (Hz)
-110
-10 dBm
-5 dBm
0 dBm
+5 dBm
-120
SSB PHASE NOISE (dBc/Hz)
SSB PHASE NOISE (dBc/Hz)
5
10
-100
-130
-140
-150
-160
-170
-110
-120
-10 dBm
-5 dBm
0 dBm
+5 dBm
-130
-140
-150
-160
-170
3
10
4
10
-180
2
10
5
10
OFFSET FREQUENCY (Hz)
3
10
4
10
5
10
OFFSET FREQUENCY (Hz)
Phase Noise Floor [1][2][3]
Ref = Square Wave, Vcc = 5.25V
Phase Noise Floor [1][2][3]
Ref = Sine Wave, Vcc = 5.25V
-100
-100
-110
-10 dBm
-5 dBm
0 dBm
+5 dBm
-120
SSB PHASE NOISE (dBc/Hz)
SSB PHASE NOISE (dBc/Hz)
4
10
Phase Noise Floor [1][2][3]
Ref = Square Wave, Vcc = 5V
-100
-130
-140
-150
-160
-170
-180
2
10
3
10
6
OFFSET FREQUENCY (Hz)
Phase Noise Floor [1][2][3]
Ref = Sine Wave, Vcc = 5V
-180
2
10
-10 dBm
-5 dBm
0 dBm
+5 dBm
-110
-10 dBm
-5 dBm
0 dBm
+5 dBm
-120
-130
-140
-150
PLL - INTEGER-n synthesizer - SMT
-110
SSB PHASE NOISE (dBc/Hz)
SSB PHASE NOISE (dBc/Hz)
-100
-160
-170
3
10
4
10
5
10
OFFSET FREQUENCY (Hz)
-180
2
10
3
10
4
10
5
10
OFFSET FREQUENCY (Hz)
[1] Phase Noise Floor vs Offset Frequency with varying Ref Power Level
[2] Fin = 7000 MHz @ 0 dBm, Ref Frequency = 100 MHz, N = 70
[3] Phase Noise Floor remains constant beyond 100 kHz offset frequency
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
6-2
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Phase Noise Floor [1][2][3]
Ref = Sine Wave @ 5 dBm, Vcc = 5V
-100
-100
-110
-110
-120
SSB PHASE NOISE (dBc/Hz)
6
SSB PHASE NOISE (dBc/Hz)
Phase Noise Floor [1][2][3]
Ref = Square Wave @ 5 dBm, Vcc = 5V
+25 C
+85 C
-40 C
-130
-140
-150
-160
-170
-180
2
10
+25 C
+85 C
-40 C
-120
-130
-140
-150
-160
-170
3
4
10
-180
2
10
5
10
10
3
10
4
5
10
10
OFFSET FREQUENCY (Hz)
Phase Noise Floor vs Offset Frequency
with varying Fin @ 0 dbm, Ref = 100 MHz
Square Wave @ 5 dBm, Vcc = 5V [3]
Absolute Maximum Ratings
RF Input (Vcc = +5V)
+10 dBm
Supply Voltage (Vcc)
+5.5V
Logic Inputs
-0.5V to (0.5V + Vcc)
Junction Temperature (Tc)
135 °C
Continuous Pdiss (T = 85 °C)
(derate 87 mW/°C above 85 °C)
4.3 W
-140
Thermal Resistance
(Junction to ground paddle)
11.60 °C/W
-150
Storage Temperature
-65 to +150 °C
-160
Operating Temperature
-40 to +85 °C
-100
SSB PHASE NOISE (dBc/Hz)
PLL - INTEGER-n synthesizer - SMT
OFFSET FREQUENCY (Hz)
-110
1600 MHz
7000 MHz
-120
-130
-170
-180
2
10
3
4
10
5
10
10
OFFSET FREQUENCY (Hz)
Typical DC Characteristics @ Vcc = +5V
+25°C
Symbol
Characteristics
Icc
Power Supply
Current
310
Voh
Output High
Voltage, (NU, ND)
5
5
5
V
Vol
Output Low
Voltage, (NU, ND)
2.9
3.0
3.1
V
Min.
Typ.
345
Max.
380
Typical Supply Current vs. Vcc
Vcc (V)
Units
mA
Icc (mA)
4.75
318
5.00
345
5.25
369
Note: HMC669LP5(E) will work over full voltage range above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
[1] Phase Noise Floor vs Offset Frequency over temperature
[2] Fin= 7000 MHz @ 0 dBm, Ref Frequency = 100 MHz, N = 70
[3] Phase Noise Floor remains constant beyond 100 kHz offset frequency
6-3
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
PCB LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC699LP5
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC699LP5(E)
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
H699
XXXX
H699
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
PLL - INTEGER-n synthesizer - SMT
6
6-4
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Pin Description
Pin Number
Function
Description
Interface Schematic
Pulsed output.
1
LD
Average “LOW” = UNLOCKED.
Average “HIGH” = LOCKED
PLL - INTEGER-n synthesizer - SMT
6
PFD INVERT function
CMOS compatible input control bit
2
INV
Logic “LOW” = NORMAL
Logic “HIGH” = INVERT
3, 6 - 8, 17,
19, 20, 24,
26, 29, 32
N/C
The pins are not connected internally; however, all data shown
herein was measured with these pins connected to RF/DC ground
externally.
4, 5, 18, 25
Vcc1, Vcc3,
Vcc2, Vcc_pd
Supply Voltage 5V ±0.25V
9 - 14
N0 - N5
CMOS compatible control input bit 0 (LSB) - 5
15
FIN
(These pins are AC coupled and must be DC Blocked externally.)
Frequency Input
16
NFIN
Frequency Input Complement
CMOS compatible
22, 23
S1, S0
Control Input
bit 0 (LSB) -1
6-5
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Pin Description (Continued)
Pin Number
Function
28
REF
Description
Interface Schematic
Reference Input
Reference Input Complement
27
NREF
30
ND
Down Output
31
NU
Up Output
Ground
Paddle
GND
Package bottom has an exposed ground paddle that must be
connected to RF/DC ground
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
6
PLL - INTEGER-n synthesizer - SMT
(These pins are AC coupled and must be DC Blocked externally.)
6-6
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
HMC699LP5(E) Programming
The decimal value of A counter and S counter can be defined as:
A = int (
N
)-1
8
and S = N - 8 (A + 1)
where N = 16 to 519
For a valid division ratio N, the A counter and S counter must satisfy the condition: A +1 ≥ S
PLL - INTEGER-n synthesizer - SMT
6
6-7
Therefore, N = 16 to 54 will result into non-continuous division ratio
and N = 56 to 519 will be continuous division ratio.
Example: Given a reference frequency, Fref = 11 MHz, and VCO output frequency, Fvco = (198 to 297) MHz, results
in N = 18 to 27. The decimal value of A counter and S counter for N = 18 will be:
A = int ( 18 ) - 1 = 1
8
and S = 18 - 8 (1 + 1) = 2
Since the calculated value of A and S satisfy the condition of A + 1 ≥ S, the N = 18 is usable division ratio.
The division ratio, N = 23, however, will result in A = 1 and S = 7. Under the condition A +1 ≥ S, the division ratio N =
23 is not usable.
In this example, the division ratio, N = 19 to 23 cannot be programmed and therefore, the frequency range of 209 MHz
to 253 MHz cannot be used.
HMC699LP5(E) Programming Truth Table, Continuous Division Ratios
Division
Ratio N
A Counter
Decimal Set
Swallow S
Decimal Set
(LSB)
A0
A1
A2
A3
A4
A5
(LSB)
S0
S1
S2
56
6
0
0
1
1
0
0
0
0
0
0
57
6
1
0
1
1
0
0
0
1
0
0
58
6
2
0
1
1
0
0
0
0
1
0
59
6
3
0
1
1
0
0
0
1
1
0
60
6
4
0
1
1
0
0
0
0
0
1
61
6
5
0
1
1
0
0
0
0
0
1
62
6
6
0
1
1
0
0
0
0
1
1
63
6
7
0
1
1
0
0
0
1
1
1
64
7
0
1
1
1
0
0
0
0
0
0
65
7
1
1
1
1
0
0
0
1
0
0
66
7
2
1
1
1
0
0
0
0
1
0
67
7
3
1
1
1
0
0
0
1
1
0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
HMC699LP5(E) Programming Truth Table, Continuous Division Ratios (Continued)
A Counter
Decimal Set
.
.
.
Swallow S
Decimal Set
.
.
.
(LSB)
A0
.
.
.
A1
.
.
.
A2
.
.
.
A3
.
.
.
A4
.
.
.
A5
.
.
.
(LSB)
S0
.
.
.
S1
.
.
.
S2
.
.
.
512
63
0
1
1
1
1
1
1
0
0
0
513
63
1
1
1
1
1
1
1
1
0
0
514
63
2
1
1
1
1
1
1
0
1
0
515
63
3
1
1
1
1
1
1
1
1
0
516
63
4
1
1
1
1
1
1
0
0
1
517
63
5
1
1
1
1
1
1
1
0
1
518
63
6
1
1
1
1
1
1
0
1
1
519
63
7
1
1
1
1
1
1
1
1
1
HMC699LP5(E) Programming Truth Table, Non-Continuous Division Ratios
Division
Ratio N
A Counter
Decimal Set
Swallow S
Decimal Set
(LSB)
A0
A1
A2
A3
A4
A5
(LSB)
S0
S1
S2
16
1
0
1
0
0
0
0
0
0
0
0
17
1
1
1
0
0
0
0
0
1
0
0
18
1
2
1
0
0
0
0
0
0
1
0
24
2
0
0
1
0
0
0
0
0
0
0
25
2
1
0
1
0
0
0
0
1
0
0
26
2
2
0
1
0
0
0
0
0
1
0
27
2
3
0
1
0
0
0
0
1
1
0
32
3
0
1
1
0
0
0
0
0
0
0
33
3
1
1
1
0
0
0
0
1
0
0
34
3
2
1
1
0
0
0
0
0
1
0
35
3
3
1
1
0
0
0
0
1
1
0
36
3
4
1
1
0
0
0
0
0
0
1
40
4
0
0
0
1
0
0
0
0
0
0
41
4
1
0
0
1
0
0
0
1
0
0
42
4
2
0
0
1
0
0
0
0
1
0
43
4
3
0
0
1
0
0
0
1
1
0
44
4
4
0
0
1
0
0
0
0
0
1
45
4
5
0
0
1
0
0
0
1
0
1
48
5
0
1
0
1
0
0
0
0
0
0
49
5
1
1
0
1
0
0
0
1
0
0
50
5
2
1
0
1
0
0
0
0
1
0
51
5
3
1
0
1
0
0
0
1
1
0
52
5
4
1
0
1
0
0
0
0
0
1
53
5
5
1
0
1
0
0
0
1
0
1
54
5
6
1
0
1
0
0
0
0
1
1
6
PLL - INTEGER-n synthesizer - SMT
Division
Ratio N
.
.
.
* Choose values of R2 & R4 between 4.3 and 20 Ohms for best noise performance.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
6-8
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Evaluation PCB Circuit
PLL - INTEGER-n synthesizer - SMT
6
6-9
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Evaluation PCB
The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm
impedance while the package backside ground paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation
circuit board shown is available from Hittite upon request.
List of Materials for
Evaluation PCB 116108
[1]
Item
Description
J1 - J4
PC Mount SMA RF Connector
J5 - J6
2mm DC Header
C1 - C5, C8 - C10
1000 pF Capacitor, 0402 Pkg.
C6 - C7
100 pF Capacitor, 0402 Pkg.
C15
1000 pF Capacitor, 0603 Pkg.
C16
4.7 μF Tantalum Capacitor Case A
D
LED Green, 0603 Pkg., +5V
R1
10k Ohm, Resistor, Array
R8, R10
10k Ohm, Resistor, 0402 Pkg.
R11
1k Ohm, Resistor, 0402 Pkg.
R12
100 Ohm, Resistor, 0402 Pkg.
U1
HMC699LP5(E) Synthesizer
PCB [2]
116106 Eval Board
Evaluation PCB Truth Table
(see Programming Truth Table)
Note: 0 = Jumper Installed.
1 = Jumper Not Installed.
Note: The evaluation PCB for the HMC699LP5(E) contains
10 kOhm pull up resistors for each of the control inputs A0
through A5 and S0 through S2. Programming the 489 distinct
division ratios consists of installing or removing jumpers A0
through A5 and S0 though S2.
PLL - INTEGER-n synthesizer - SMT
6
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
6 - 10
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Typical PLL Application Circuit using HMC699LP5
PLL application shown for a 13 GHz Fout. Contact HMC to discuss your specific application.
PLL - INTEGER-n synthesizer - SMT
6
6 - 11
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC699LP5 / 699LP5E
v05.0110
7 GHz INTEGER N SYNTHESIZER
CONTINUOUS (N = 56 - 519), NON-CONTINUOUS (N = 16 - 54)
Typical Application
Showing Spurious Performance
Typical Application
13 GHz Measured Phase Noise [1]
-110
-120
-130
MEASURED
CALCULATED
-140
-150
6
-160
-170
-180
2
10
3
4
10
10
5
10
6
10
7
10
OFFSET FREQUENCY (Hz)
[1] Phase Noise Floor remains constant beyond 100 kHz offset
frequency. Measured phase noise using Agilent 5500 with 2 unit
measurement technique and corresponding calculated phase noise
floor.
CMOS/TTL Input Characteristics
Maximum Input Logic “0” Voltage (VIL MAXIMUM) = 1.1V @ 1 µA.
Minimum Input Logic “1” Voltage (VIH MINIMUM) = 1.8V @ 50 µA.
Input IV characteristics for the logic inputs (A0 - A5 and S0 - S2) are shown below:
0.4
V
Input Current (mA)
V
IL MAX
0.3
IH MIN
0.2
0.1
0
-0.1
0
1
2
3
4
5
PLL - INTEGER-n synthesizer - SMT
SSB PHASE NOISE (dBc/Hz)
-100
Input Voltage (V)
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, 20
delivery,
and
to place
orders: Analog
For price,
delivery
and
to place
orders:
Microwave
Corporation,
Alpha
Road,
Chelmsford,
MADevices,
01824 Inc.,
responsibility
is assumed
by Analog
Devices
for its use,
nor for anyHittite
infringements
of patents or other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
6 - 12
工商网监
湘ICP备2023018690号
