119351-HMC862LP3E

HMC862LP3E v03.1210 Typical Applications Features The HMC862LP3E is ideal for: Low Noise Floor: -153 dBc/Hz at 100 kHz offset • Satellite Communication Systems Programmable Frequency Divider, N = 1, 2, 4, 8 • Point-to-Point & Point-to-Multi-Point Radios Wide Bandwidth: 100 MHz to 15 GHz • Military Applications 16 Lead 3X3 mm SMT Package: 9mm 2 • Test Equipment Functional Diagram TE General Description B SO LE The HMC862LP3E is a low noise programmable frequency divider in a 3x3 mm leadless surface mount package. The divider can be programmed to divide from N=1, 2, 4, 8 in the 100 MHz to 15 GHz input frequency range. The low phase noise, wide frequency range and flexible division ratio make this device ideal for high performance and wide band communication systems. Electrical Specifications, TA = +25° C, Vcc1 = Vcc2 = +5V Parameter Conditions Min. Max RF Input Frequency Sine Wave or Square Wave Input 15 Min RF Input Frequency Sine Wave or Square Wave Input [1] Typ. Max. Units RF Input Characteristics RF Input Power Range (N = 1) RF Input Power Range (N = 2, 4, 8) Sine Wave or Square Wave Input [1] [2] Fin < 8 GHz GHz -10 0.1 GHz 10 dBm Sine Wave or Square Wave Input [1] [2] Fin > 8 GHz -10 0 dBm Sine Wave or Square Wave Input [1] -10 10 dBm Divider Output Characteristics Output Power (N = 1) O Frequency Dividers & Detectors - SMT 4 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Output Power (N = 2, 4, 8) (see the Pout plot for N = 1) [2] -2 to +3 dBm (see the Pout plots for each division ratio) 2 dBm Divider Ratio N SSB Phase Noise @ 100 kHz Offset 1, 2, 4, 8 Fin = 6 GHz, Pin = 0 dBm, N = 2 -153 dBc/Hz Logic Inputs VIH Input High Voltage 3 5 V VIL Input Low Voltage 0 0.4 V 5.25 V Power Supplies Vcc Analog Supply 4.75 5 Current Consumption Icc Control Bits N = 1, S0 = L, S1 = L, S2 = L 106 N = 2, S0 = H, S1 = L, S2 = L 143 mA mA N = 4, S0 = H, S1 = H, S2 = L 153 mA N = 8, S0 = H, S1 = H, S2 = H 162 mA 3 Bit [1] Square wave input waveform is recommended below 400 MHz for best phase noise performance. If sine wave input waveform is used below 400 MHz, it is recommended that power input is > +5 dBm for best operation including phase noise performance. [2] For N = 1, frequencies > 8 GHz, and input power > 0 dBm, output power will saturate and gradually drop with increasing input power, but part will continue to function. 4-1 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Divide-by-1 10 6 OUTPUT POWER (dBm) 8 5 0 -5 -10 -15 -20 0 -2 +25C +85C -40C -4 -6 -8 -25 0 2 4 6 8 10 12 14 16 18 -10 20 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 INPUT FREQUENCY (GHz) LE INPUT FREQUENCY (GHz) Phase Noise vs. Frequency, Pin = 0 dBm -120 Phase Noise vs. Temperature, Pin = 0 dBm, Fin = 6 GHz -120 -125 100MHz SQ 100MHz SINE 6 GHz 15 GHz -130 -135 -140 -145 -150 -155 -160 1.0e+2 B SO SSB PHASE NOISE (dBc/Hz) 2 TE Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C 4 1.0e+3 1.0e+4 1.0e+5 1.0e+6 -140 -150 -160 1.0e+2 1.0e+7 1.0e+3 OFFSET FREQUENCY (Hz) O Output Harmonics, Pin = 0 dBm T = 25 °C +25C +85C -40C -130 1.0e+4 1.0e+5 1.0e+6 1.0e+7 OFFSET FREQUENCY (Hz) Reverse Leakage, Pin = 0 dBm T = 25 °C 10 0 -10 -10 POWER LEVEL (dBm) OUTPUT LEVEL (dBm) 0 -20 -30 -40 Pfeedthru 3rd Harmonic -50 -20 -30 Both Output Ports Terminated One Output Port Terminated -40 -60 -70 0 2 4 6 8 10 4 Frequency Dividers & Detectors - SMT Output Power vs. Temperature, Pin = 0 dBm 15 SSB PHASE NOISE (dBc/Hz) INPUT POWER (dBm) Input Sensitivity vs. Temperature 12 14 INPUT FREQUENCY (GHz) 16 18 20 -50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INPUT FREQUENCY (GHz) Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 4-2 HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Divide-by-2 Output Power vs. Temperature, Pin = 0 dBm 8 10 6 OUTPUT POWER (dBm) 15 5 0 -5 -10 -15 -20 -25 0 2 4 6 8 10 12 14 16 18 0 -2 +25C +85C -40C -4 -6 -10 20 0.0 2.0 4.0 6.0 10.0 12.0 LE Phase Noise vs. Frequency, Pin = 0 dBm -120 14.0 16.0 18.0 20.0 Phase Noise vs. Temperature Pin = 0 dBm, Fin = 6 GHz -120 100MHz SQ 100MHz SINE 6 GHz 15 GHz -140 -150 -160 -170 1.0e+2 B SO -130 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 O Output Harmonics, Pin = 0 dBm T = 25 °C +25C +85C -40C -130 -140 -150 -160 1.0e+2 1.0e+3 OFFSET FREQUENCY (Hz) 1.0e+4 1.0e+5 1.0e+6 1.0e+7 OFFSET FREQUENCY (Hz) Reverse Leakage, Pin = 0 dBm T = 25 °C 10 0 0 -10 -20 POWER LEVEL (dBm) -10 -20 -30 -40 Pfeedthru 3rd Harmonic -50 -70 8.0 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) SSB PHASE NOISE (dBc/Hz) 2 -8 -60 -30 -40 -50 -60 -70 Both Output Ports Terminated One Output Port Terminated -80 -90 0 2 4 6 8 10 12 14 INPUT FREQUENCY (GHz) 4-3 4 TE Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C SSB PHASE NOISE (dBc/Hz) INPUT POWER (dBm) Input Sensitivity vs. Temperature OUTPUT LEVEL (dBm) Frequency Dividers & Detectors - SMT 4 16 18 20 -100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INPUT FREQUENCY (GHz) Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Divide-by-4 10 6 OUTPUT POWER (dBm) 8 5 0 -5 -10 -15 -20 2 0 -2 +25C +85C -40C -4 -6 -8 -25 0 2 4 6 8 10 12 14 16 18 -10 20 0.0 2.0 4.0 -120 10.0 12.0 14.0 16.0 18.0 20.0 Phase Noise vs. Temperature Pin = 0 dBm, Fin = 6 GHz -120 100MHz SQ 100MHz SINE 6 GHz 15 GHz -140 -150 -160 B SO -130 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 -130 -150 -160 1.0e+2 1.0e+7 O Output Harmonics, Pin = 0 dBm T = 25 °C 1.0e+3 1.0e+4 0 -10 POWER LEVEL (dBm) -20 -30 -40 Pfeedthru 3rd Harmonic -50 -60 -30 -40 -50 -60 -70 -80 Both Output Ports Terminated One Output Port Terminated -90 6 8 10 1.0e+7 4 -20 -10 4 1.0e+6 Reverse Leakage, Pin = 0 dBm T = 25 °C 0 2 1.0e+5 OFFSET FREQUENCY (Hz) 10 0 +25C +85C -40C -140 OFFSET FREQUENCY (Hz) OUTPUT LEVEL (dBm) 8.0 LE Phase Noise vs. Frequency, Pin = 0 dBm -70 6.0 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) SSB PHASE NOISE (dBc/Hz) 4 TE Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C SSB PHASE NOISE (dBc/Hz) INPUT POWER (dBm) 15 Frequency Dividers & Detectors - SMT Output Power vs. Temperature, Pin = 0 dBm Input Sensitivity vs. Temperature 12 14 INPUT FREQUENCY (GHz) 16 18 20 -100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INPUT FREQUENCY (GHz) Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 4-4 HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Divide-by-8 Output Power vs. Temperature, Pin = 0 dBm 8 10 6 OUTPUT POWER (dBm) 15 5 0 -5 -10 -15 -20 0 -2 +25C +85C -40C -4 -6 -10 2 4 6 8 10 12 14 INPUT FREQUENCY (GHz) 16 18 20 0.0 2.0 4.0 Phase Noise vs. Frequency, Pin = 0 dBm -120 8.0 10.0 12.0 14.0 16.0 18.0 20.0 Phase Noise vs. Temperature Pin = 0 dBm, Fin = 6 GHz -120 100MHz SQ 100MHz SINE 6 GHz 15 GHz -140 -150 -160 -170 1.0e+2 B SO -130 1.0e+3 1.0e+4 1.0e+5 1.0e+6 -140 -150 -160 1.0e+2 1.0e+7 O Output Harmonics, Pin = 0 dBm T = 25 °C +25C +85C -40C -130 1.0e+3 1.0e+4 1.0e+5 0 0 -10 -20 POWER LEVEL (dBm) -10 -20 -30 -40 Pfeedthru 3rd Harmonic -50 -30 -40 -50 -60 -70 -80 Both Output Ports Terminated One Output Port Terminated -90 2 4 6 8 10 1.0e+7 Reverse Leakage, Pin = 0 dBm T = 25 °C 10 0 1.0e+6 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) -70 6.0 INPUT FREQUENCY (GHz) LE 0 SSB PHASE NOISE (dBc/Hz) 2 -8 -25 -60 12 14 INPUT FREQUENCY (GHz) 4-5 4 TE Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C SSB PHASE NOISE (dBc/Hz) INPUT POWER (dBm) Input Sensitivity vs. Temperature OUTPUT LEVEL (dBm) Frequency Dividers & Detectors - SMT 4 16 18 20 -100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INPUT FREQUENCY (GHz) Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) 150 100 0 4.7 4.8 4.9 5 S2 Divider Ratio (N) 0 0 1 1 0 0 2 1 1 0 4 1 1 1 8 Digital Control Input Voltages 5.1 5.2 5.3 Absolute Maximum Ratings State S0, S1, S2 Low 0 to 0.4V High 3V to 5V LE Vcc (V) 13 dBm Supply Voltage (Vcc) 5.5V Logic Inputs (S0, S1, S2) -0.5V to (0.5V + Vcc) Storage Temperature -65 to +125 °C Reliability Information B SO RF Input Power ESD Sensitivity (HBM) S1 0 0 = Logic Low 1 = Logic High Note: Vcc1, Vcc2 must be applied before logic. N=1 N=2 N=4 N=8 50 S0 TE OPERATING CURRENT (mA) 200 Class 1A Junction Temperature to Maintain 1 Million Hour MTTF 150 °C Nominal Junction Temperature (T = 85 °C) 112 °C Thermal Resistance (Junction to GND Paddle, 5V Supply) 33 °C/W Operating Temperature -40 to +85 °C O ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 4 Frequency Dividers & Detectors - SMT Programming Truth Table for Frequency Division Ratios Icc vs. Vcc 4-6 HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) 4-7 TE NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY LE 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. B SO Package Information Part Number Package Body Material Lead Finish HMC862LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] 862 XXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 °C O Frequency Dividers & Detectors - SMT 4 Outline Drawing Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Function Description 1, 4, 8, 9, 12, 14, 15 GND Ground: Backside of package has exposed metal ground slug which must be connected to RF/DC ground. 2 IN RF Input must be DC blocked. 3 NIN RF Input 180° out of phase with pin 2 for differential operation. AC ground for single ended operation. DC block for differential operation. 5, 6, 7 S0, S1, S2 CMOS compatible division ratio control bit. See Programming Truth Table Interface Schematic B SO LE TE Pin Number NOUT Divider output 180° out of phase with pin 11. RF output must be DC blocked. 11 OUT Divided Output. RF output must be DC blocked. O 10 13, 16 Vcc1, Vcc2 Supply voltage 5V. Connect both pins to +5V supply. Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 4 Frequency Dividers & Detectors - SMT Pin Description 4-8 HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) TE LE B SO List of Materials for Evaluation PCB 119351 O Frequency Dividers & Detectors - SMT 4 Evaluation PCB Item Description J1 - J3 PCB Mount SMA-F RF Connector J4 DC Connector Header, Molex 2mm C1 - C4 ATC530L, 100 nF, 16V, Broadband Capacitor, 0402 Pkg. C5, C6 1000 pF Capacitor, 0402 Pkg. C7, C8 4.7 µF Capacitor, Tantalum, 1206 Pkg. R1 - R3 10 kOhm Resistor, 0402 Pkg. Vcc1, Vcc2 Mill-Max 0.040" Dia. PC Pin, 3101-2-00-21-00-00-08-0 U1 HMC862LP3E, Programmable Divider PCB [2] 119349 Evaluation Board [1] The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and backside ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR 4-9 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Evaluation PCB Schematic Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com Frequency Dividers & Detectors - SMT O B SO LE TE 4 4 - 10