HMC794LP3E
v01.0612
Frequency Dividers & Detectors - SMT
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
Typical Applications
Features
The HMC794LP3E is ideal for:
Low Noise Floor: -163 dBc/Hz at 10 MHz offset
and -160 dBc/Hz at 100 kHz offset
• LO Generation with Low Noise Floor
Programmable Frequency Divider, N = 1, 2, 3 or 4
• Clock Generators
200 MHz to 2 GHz Input Frequency Range
• Mixer LO Drive
50% Duty Cycle Outputs
• Military Applications
Up to +10 dBm Output Power
• Test Equipment
Sleep Mode: Consumes 5 dBm
-2
3
10
dBm
Programmable in 2 steps
(see the Pout plots for each division ratio)
-3
10
12
dBm
Divider Output Characteristics
Differential Output Power
SSB Phase Noise @ 10 MHz Offset
SSB Phase Noise @ 100 kHz Offset
+5 dBm Input Power, 2 GHz Input
SSB Phase Noise @ 10 kHz Offset
Duty Cycle for Differential Mode
+5 dBm Input Power
-163
dBc/Hz
-160
dBc/Hz
-153
dBc/Hz
50 ±3
%
Logic Inputs
1
VIH Input High Voltage
3
5
V
VIL Input Low Voltage
0
0.4
V
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC794LP3E
v01.0612
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
Parameter
Conditions
Min.
Typ.
Max.
Units
Analog Supply
4.75
5
5.25
V
5V Supply
100
150
mA
5V supply, CTRL = 0V, BIAS0 = 0V
CTRL = 0V, BIAS0 = 5V
CTRL = 5V, BIAS0 = 0V
100
109
115
130
150
150
mA
mA
mA
1
µA
Power Supplies
Vcc
Current Consumption
Itot - Total Current Consumption
Itot - Total Current Consumption [1]
Sleep Current
EN = 0V
CBias Reference Voltage
[2]
Measured with 10 GΩ Volt meter
3.8
V
[1] Bias0 = 0V, for maximum frequency range; Bias0 = 5V, for better phase noise floor; CTRL = 5V, for maximum output power
[2] CBias voltage pin cannot drive external load. It must be measured with a 10 GΩ volt meter such as Agilent 34410A, typical 10 MOhms DVM
will read erroneously.
Residual Phase Noise
Divide by 1, 2, 3 & 4, (Differential) [3]
20
-120
15
-130
SSB PHASE NOISE (dBc/Hz)
INPUT POWER (dBm)
Input Sensitivity Window
10
Recommended
Operating Window
5
0
-5
-10
0
0.5
1
1.5
2
Div By 1
Div By 2
Div By 3
Div By 4
-140
-150
-160
-170
-180
1
10
2.5
10
2
INPUT FREQUENCY (GHz)
15
15
10
10
5
Div by 1
Div by 2
Div by 3
Div by 4
-5
-10
0
0.5
1
1.5
2
3
10
4
10
5
10
6
10
7
Pout vs. Div Ratio [4], (Differential)
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
Pout vs. Div Ratio [4], (Single-Ended)
0
10
OFFSET FREQUENCY (Hz)
2.5
INPUT FREQUENCY (GHz)
3
Frequency Dividers & Detectors - SMT
Electrical Specifications, TA = +25° C, Vcc = +5V, Zo = 50Ω, Bias1 = GND (Continued)
5
0
Div by 1
Div by 2
Div by 3
Div by 4
-5
-10
0
0.5
1
1.5
2
2.5
3
INPUT FREQUENCY (GHz)
[3] CTRL = +5V, Bias0 = 0V, Pin = +8 dBm @ 2 GHz
[4] CTRL = +5V, Bias0 = 0V, Pin = +4 dBm
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
2
HMC794LP3E
v01.0612
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
10
5
5
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
Pout Divide-by-2 vs. Temperature [1],
(Single-Ended)
10
0
-5
+25°C
+85°C
-40°C
-10
-15
0
0.5
1
1.5
2
2.5
0
-10
-15
3
+25°C
+85°C
-40°C
-5
0
0.5
INPUT FREQUENCY (GHz)
5
5
OUTPUT POWER (dBm)
10
0
+25°C
+85°C
-40°C
-10
-15
0
0.5
1
1.5
2
2.5
2.5
3
+25°C
+85°C
-40°C
-5
-10
-15
3
0
0.5
1
1.5
2
2.5
3
INPUT FREQUENCY (GHz)
Pout Divide-by-3 vs. CTRL & Bias0 [2]
(Single-Ended)
Pout Divide-by-4 vs. CTRL & Bias0 [2]
(Differential)
10
15
10
OUTPUT POWER (dBm)
5
OUTPUT POWER (dBm)
2
0
INPUT FREQUENCY (GHz)
0
CTRL = 0V, BIAS0= 0V
CTRL = 5V, BIAS0 = 0V
CTRL = 0V, BIAS0 = 5V
-5
-10
-15
1.5
Pout Divide-by-4 vs. Temperature [1],
(Single-Ended)
10
-5
1
INPUT FREQUENCY (GHz)
Pout Divide-by-3 vs. Temperature [1],
(Single-Ended)
OUTPUT POWER (dBm)
Frequency Dividers & Detectors - SMT
Pout Divide-by-1 vs. Temperature [1],
(Single-Ended)
0
0.5
1
1.5
2
2.5
INPUT FREQUENCY (GHz)
3
5
0
CTRL = 0V, BIAS0 = 0V
CTRL = 5V, BIAS0 = 0V
CTRL = 0V, BIAS0 = 5V
-5
-10
-15
0
0.5
1
1.5
2
2.5
3
INPUT FREQUENCY (GHz)
[1] CTRL = 0V, Bias0 = 0V, Pin = +4 dBm [2] Pin = +4 dBm
3
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC794LP3E
v01.0612
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
10
10
5
5
+25°C
+85°C
-40°C
0
-5
-10
-15
0
0.5
1
1.5
2
2.5
5.25V
-5
-10
-15
3
4.75V
5.00V
0
0
0.5
INPUT FREQUENCY (GHz)
Divide-by-1 Harmonics [1], (Differential)
-10
OUTPUT LEVEL (dBc)
OUTPUT LEVEL (dBc)
2.5
3
H2
H3
H4
H5
0
-20
-30
-40
H2
H3
H4
H5
-50
-60
0
0.5
1
1.5
2
2.5
-10
-20
-30
-40
-50
3
0
0.5
INPUT FREQUENCY (GHz)
1
1.5
2
2.5
3
INPUT FREQUENCY (GHz)
Divide-by-3 Harmonics [1], (Differential)
Divide-by-4 Harmonics [1], (Differential)
10
10
0
H2
H3
-10
H4
H5
-20
-30
-40
0
0.5
1
1.5
2
INPUT FREQUENCY (GHz)
H2
H3
H4
H5
0
OUTPUT LEVEL (dBc)
OUTPUT LEVEL (dBc)
2
10
0
-50
1.5
Divide-by-2 Harmonics [1], (Differential)
10
-70
1
INPUT FREQUENCY (GHz)
2.5
3
Frequency Dividers & Detectors - SMT
Pout Divide-by-4 vs. Supply Voltage [1],
(Differential)
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
Pout Divide-by-4 vs. Temperature [1],
(Differential)
-10
-20
-30
-40
-50
0
0.5
1
1.5
2
2.5
3
INPUT FREQUENCY (GHz)
[1] CTRL = 0V, Bias0 = 0V, Pin = +4 dBm
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
4
HMC794LP3E
v01.0612
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
Divide-by-4 Harmonics [1], (Differential)
Divide-by-4 Harmonics [2], (Single-Ended)
0
-10
OUTPUT LEVEL (dBc)
0
OUTPUT LEVEL (dBc)
Frequency Dividers & Detectors - SMT
10
-10
-20
-30
H2
H3
H4
H5
-40
-50
0
0.5
1
1.5
2
-20
-30
-40
H2
H3
H4
H5
-50
-60
2.5
3
-70
0
0.5
INPUT FREQUENCY (GHz)
Absolute Maximum Ratings
RF Input Power
13 dBm
Supply Voltage (Vcc)
5.5V
1
1.5
2
2.5
3
INPUT FREQUENCY (GHz)
Programming Truth Table
for Frequency Division Ratios
B1
B0
0
0
Divide-by
1
0
1
2
Control Inputs
(B0, B1, CTRL, Bias0, EN)
5.5V
Junction Temperature
125 °C
Continuous Pdiss (T = 85 °C)
(derate 33 mW/ °C above 85 °C)
1.3W
Thermal Resistance
(Junction to ground paddle)
30 °C/W
Storage Temperature
-65 to +125 °C
Operating Temperature
-40 to +85 °C
State
B0, B1, CTRL, BIAS1, BIAS0, EN
Class 1A
Low
0 to 0.4V
High
3V to 5V
ESD Sensitivity (HBM)
1
0
3
1
1
4
0 = Logic Low
1 = Logic High
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Digital Control Input Voltages
Typical Supply Current vs. Vcc
Vcc (V)
Icc (mA)
4.75
105*
5.00
115*
5.25
125*
Note: HMC794LP3E will work over full voltage range above.
* For CTRL = 0V, Bias0 = 0V
[1] CTRL = 5V, Bias0 = 0V, Pin = +4 dBm
5
[2] CTRL = 0V, Bias0 = 0V, Pin = +4 dBm
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC794LP3E
v01.0612
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
PCB LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
HMC794LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL Rating
MSL1
[2]
Package Marking [1]
794
XXX
[1] 4-Digit lot number XXXX
[2] Max peak reflow temperature of 260 °C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
Frequency Dividers & Detectors - SMT
Outline Drawing
6
HMC794LP3E
v01.0612
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
Frequency Dividers & Detectors - SMT
Pin Description
Pin Number
Function
Description
1
Vcc
+5V Voltage Supply
2
RFINP
RF Positive Input.
Input is DC coupled, external DC blocks required..
3
RFINN
RF Negative Input.
Input is DC coupled, external DC blocks required...
4
GND
this pin must be connected to RF/DC ground.
5
B0
Division ratio (LSB)
See programming truth table.
6
B1
Division ratio (MSB)
See programming truth table.
7
CTRL
Divider Output Buffer Power Control
13
BIAS1
For proper operation this pin should be grounded.
14
BIAS0
Digital Core Bias Control [1]
15
EN
Chip Enable
8, 9, 12
N/C
No connection required. This pin may be
connected to ground, without affecting performance.
Interface Schematic
[1] Divider Core Bias Control Bit
Bias0 = 0V, Divider Core Minimum Bias
Bias0 = 5V, Divider Core Maximum Bias
7
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC794LP3E
v01.0612
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
Pin Description (Continued)
Function
Description
10
IOUTN
Divider Negative Output, Open Drain.
Typically 100 Ohms connected to Vcc.
11
IOUTP
Divider Positive Output, Open Drain.
Typically 100 Ohms connected to Vcc.
16
CBIAS
External Bypass Decoupling for Precision/Low Noise Bias
Circuit
Interface Schematic
Frequency Dividers & Detectors - SMT
Pin Number
Application Note:
The HMC794LP3E is a high performance RF divider. Such dividers are high gain devices with internal feedback.
The device will oscillate if used with AC coupled RF inputs and if no RF input is applied. Normally, if the RF input
signal is removed the device should be disabled, or it should be placed in divide by 1 mode. The device is stable
in divide by one mode with no RF input. The device will oscillate in divide 2, 3, or 4 modes with no RF input. In
general very small RF input levels will stop all oscillations. At the minimum rated RF input sensitivity level or higher,
no oscillations or spurious signals exist and excellent low noise performance is achieved.
For input frequency lower than 200 MHz, square wave input signal is recommended.
The divider output power for the differential mode, shows a roll off at lower frequencies due to the limited frequency
range of the T6 & T7 (4:1) RF transformers, 500 MHz to 3000 MHz.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
8
HMC794LP3E
v01.0612
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
Frequency Dividers & Detectors - SMT
Evaluation PCB
9
List of Materials for Evaluation PCB 124842
[1]
Item
Description
Item
Description
J3
DC Connectors
T6, T7
4:1 RF Transformer, MABACT0065
J7, J8
SMA-F Johnson Connector
TP1, TP3, TP4
PC Compact SMT
FB1, FB2
Murata BLM21AG02SNID
C1, C2, C4, C6,
C10, C11 C12, C18
1 nF Capacitor, 0402 Pkg.
C3, C9, C14, C30,
C31, C33, C34, C36
0.1 µF Capacitor, 0402 Pkg.
C5
10 µF Capacitor, 1206 Pkg.
C7
10,000 pF Capacitor, 0402 Pkg.
C8
10 pF Capacitor, 0402 Pkg.
C15, C35, C37,
C68, C69, C72, C74
4.7 µF Capacitor, 0805 Pkg.
C32
1 µF Capacitor, 0603 Pkg.
R1, R7
100 Ohm, Resistor, 0402 Pkg.
R2 - R6, R9
100 kOhm, Resistor, 0402 Pkg.
R8, L2
0 Ohm, Resistor, 0402 Pkg.
R47
27 k Ohm, Resistor, 0402 Pkg.
R48
15 k Ohm, Resistor, 0402 Pkg.
U1
HMC794LP3E Programmable Divider
U9
Hittite Ultra Low Noise Quad Regulator
PCB [2]
124709 Eval Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR
The circuit board used in the application should use
RF circuit design techniques. Signal lines should have
50 Ohm impedance while the package ground leads
and backside ground paddle should be connected
directly to the ground plane similar to that shown. A
sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon
request.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
HMC794LP3E
v01.0612
2 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1 to 4)
Frequency Dividers & Detectors - SMT
Evaluation PCB Schematic
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price,2 delivery,
andDrive,
to place
orders: AnalogMA
Devices,
For price,
delivery
andDevices
to place
orders:
Hittite
Microwave
Elizabeth
Chelmsford,
01824Inc.,
responsibility
is assumed
by Analog
for its use,
nor for any
infringements
of patents orCorporation,
other
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 978-250-3343
Fax: 978-250-3373
Order
at www.hittite.com
Phone: On-line
781-329-4700
• Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Application
Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are
the property of their
respective owners.
Application
Support:
Phone: 978-250-3343
or apps@hittite.com
10
工商网监
湘ICP备2023018690号
