126968-HMC857LC5

HMC857LC5 v02.0111 Typical Applications Features The HMC857LC5 is ideal for: Supports High Data Rates: up to 14 Gbps • SONET OC-192 and 10 GbE Differential or Single-Ended Inputs / Outputs • 16G Fiber Channel Fast Rise and Fall Times: 21 / 21 ps • Networking & Storage Low Power Consumption: 345 mW typ. • 1:2 Fanout with Input Mux Programmable Differential Output Voltage Swing: 475 - 1200 mVp-p Propagation Delay: 117 ps Single Supply: -3.3 V 32 Lead Ceramic 5 x 5 mm SMT Package: 25 mm2 Functional Diagram General Description The HMC857LC5 is a 2x2 Crosspoint Switch designed to support data transmission rates of up to 14 Gbps and selector port operation up to 14 GHz. The selector routes the differential inputs to either one or both of the desired outputs upon assertion of the appropriately selected port. ic All differential inputs to the HMC857LC5 are CML and terminated on-chip with 50 Ohms to the positive supply, GND, and may be DC or AC coupled. Outputs can be connected directly to a 50 Ohm groundterminated system or drive devices with CML logic input. The HMC857LC5 also features an output level control pin, VR, which allows for loss compensation or signal level optimization. The HMC857LC5 operates from a single -3.3 V supply and is available in ROHScompliant 3x3 mm SMT package. M ig H itt ite HIGH SPEED LOGIC - SMT • Dual 2:1 Selector ik C row ey o a C nfid ve or e C po nt o ra ial rpo tio ra n tio U n se O nl y 3 14 Gbps, 2 x 2 CROSSPOINT SWITCH WITH PROGRAMMABLE OUTPUT VOLTAGE rD Electrical Specifications, TA = +25 °C, Vee = -3.3 V, Vr = 0 V Parameter Conditions Fo Power Supply Voltage Min. Typ. Max -3.6 -3.3 -3.0 V Power Supply Current 105 mA Maximum Data Rate 14 Gbps Maximum Select Rate 14 GHz Input Voltage Range -1.5 0.5 V Input Differential Range 0.1 2.0 Vp-p Input Return Loss Output Amplitude 3-1 Units Frequency A L X IN0 ->B H X IN1 -> B H = Positive voltage level L = Negative voltage level Notes: D = DP - DN IN0 = IN0P - IN0N IN1 = IN1P - IN1N [1] VR = 0.0 V [2] Device measured on evaluation board with port extensions [3] Vee = -3.3 V For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 3-4 HMC857LC5 v02.0111 14 Gbps, 2 x 2 CROSSPOINT SWITCH WITH PROGRAMMABLE OUTPUT VOLTAGE Absolute Maximum Ratings -2.0 V to 0.5 V Output Signals -1.5 V to 0.5 V Junction Temperature 125 °C Continuous Pdiss (T = 85 °C (derate 33.0 mW/°C above 85 °C) 1.33 W Thermal Resistance (Rth j-p) Worst case device to package paddle Storage Temperature ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS ik C row ey o a C nfid ve or e C po nt o ra ial rpo tio ra n tio U n se O nl y -3.75 V to +0.5 V Input Signals 30 °C/W -65 °C to +150 °C Operating Temperature -40 °C to +85 °C M ic Outline Drawing Fo rD ig H itt ite HIGH SPEED LOGIC - SMT 3 Power Supply Voltage (Vee) 3-5 NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA 2. LEAD AND GROUND PADDLE PLATING: 30-80 MICROINCHES GOLD OVER 50 MICROINCHES MINIMUM NICKEL. 3. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm DATUM -C6. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. 7. PADDLE MUST BE SOLDERED TO Vee. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC857LC5 v02.0111 14 Gbps, 2 x 2 CROSSPOINT SWITCH WITH PROGRAMMABLE OUTPUT VOLTAGE Pin Descriptions Description 1, 4, 5, 8, 11, 14, 17, 20, 21, 24 GND Signal Grounds 2, 3, 6, 7 In0+, In0-, In1+, In1- 9, 10, 15, 16 SelB+, SelB-, SelA+, SelA- 12, 13, 25, 29, 32 N/C 18, 19, 22, 23 OutB-, OutB+, OutA-, OutA+ Interface Schematic Differential Inputs: Current Mode Logic (CML) referenced to positive supply. Differential Select Inputs: Current Mode Logic (CML) referenced to positive supply. No connection necessary. These pins may be connected to RF/DC ground without affecting performance. M ic Differential Outputs: Current Mode Logic (CML) referenced to positive supply. GND ite 26, 31 Vee itt 27, 30 Package Base VR Supply Ground These pins and the exposed paddle must be connected to the negative voltage supply. Output level control. Output level may be increased or decreased by applying a voltage to VR per “Output Differential vs. VR” plot. Fo rD ig H 28 3 HIGH SPEED LOGIC - SMT Function ik C row ey o a C nfid ve or e C po nt o ra ial rpo tio ra n tio U n se O nl y Pin Number For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 3-6 HMC857LC5 v02.0111 14 Gbps, 2 x 2 CROSSPOINT SWITCH WITH PROGRAMMABLE OUTPUT VOLTAGE ig H itt ite M ic HIGH SPEED LOGIC - SMT 3 ik C row ey o a C nfid ve or e C po nt o ra ial rpo tio ra n tio U n se O nl y Evaluation PCB rD List of Materials for Evaluation PCB 126968 [1] Description J1 - J6, J9 - J14 PCB Mount SMA RF Connectors J15 - J20 DC Pin JP1 C1, C2 C3 - C5 R1 Fo Item 0.1” Header with Shorting Jumper 4.7 µF Capacitor, Tantalum 330 pF Capacitor, 0402 Pkg. 10 Ohm Resistor, 0603 Pkg. U1 HMC857LC5 2 x 2 Crossbar Switch PCB [2] 126966 Evaluation Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 4350 3-7 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. The exposed package base should be connected to Vee. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Install jumper on JP1 to short VR to GND for normal operation. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC857LC5 v02.0111 14 Gbps, 2 x 2 CROSSPOINT SWITCH WITH PROGRAMMABLE OUTPUT VOLTAGE HIGH SPEED LOGIC - SMT 3 Fo rD ig H itt ite M ic ik C row ey o a C nfid ve or e C po nt o ra ial rpo tio ra n tio U n se O nl y Application Circuit For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 3-8