129022-HMC839LP6CE

HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz plls w/ integrated vco - SMT Features 0-1 • Tri-band RF Bandwidths: 1050 - 1205, 2100 - 2410, 4200 - 4820 MHz • Ultra Low Phase Noise -112 dBc/Hz in Band Typ. • Figure of Merit (FOM) -227 dBc/Hz • < 180 fs RMS Jitter • 24-bit Step Size, Resolution 3 Hz typ • Exact Frequency Resolution Mode • Built-In Digital Self Test • 40 Lead 6x6 mm SMT Package: 36 mm2 Typical Applications • Cellular/4G Infrastructure • Phased Array Applications • Repeaters and Femtocells • DDS Replacement • Communications Test Equipment • Very High Data Rate Radios • CATV Equipment Functional Diagram Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz The HMC839LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) with an Integrated Voltage Controlled Oscillator (VCO). The PLL consists of an integrated low noise VCO with a tri-band output, an autocalibration subsystem for low voltage VCO tuning, a very low noise digital Phase Detector (PD), a precision controlled charge pump, a low noise reference path divider and a fractional divider. The fractional PLL features an advanced delta-sigma modulator design that allows both ultra-fine step sizes and low spurious products. The phase detector (PD) features cycle slip prevention (CSP) technology to allow faster frequency hopping times. Ultra low in-close phase noise and low spurious also allows wider loop bandwidths for faster frequency hopping and low micro-phonics. For theory of operation and register map refer to the “PLLs with Integrated VCOs - RF VCOs Operating Guide”. To view the Operating Guide, please visit www.hittite.com and choose HMC839LP6CE from the “Search by Part Number” pull down menu. Electrical Specifications, TA = +25° C, VPPCP, VDDCP, VCC1, VCC2 = 5V ±4%; RVDD, AVDD, DVDD3V, VCCPD, VCCHF, VCCPS = 3.3V ±6% GNDCP = GNDLS = Ground Paddle = 0V, 100 MHz Reference Unless Otherwise Noted. Parameter Condition Min. Typ. Max. Units VCO Frequency at PLL Input 2100 RF Output Frequency at f VCO/2 1050 2200 2410 MHz 1100 1205 RF Output Frequency at f VCO MHz 2100 2200 2410 MHz RF Output Frequency at 2f VCO 4200 4400 4820 MHz RF Output Power at f VCO/2 7.5 10 12.5 dBm RF Output Power at f VCO 3.5 7 12 dBm RF Output Characteristics RF Output Power at 2f VCO VCO Tuning Sensitivity VCO Supply Pushing Measured at fo, 2V (N= 0/15/31) -9 -4 1 dBm 10 13 18 MHz/V Measured at fo, 2V 1.6 MHz/V RF Output fo/2 Harmonic Doubler Mode -26 dBc RF Output 3fo/2 Harmonic Doubler Mode -35 dBc RF Output 2nd Harmonic fo/2/fo/2fo -23 / -28 / -41 dBc RF Output 5fo/2 Harmonic Doubler Mode -48 dBc RF Output 3rd Harmonic RF Output 7fo/2 Harmonic RF Output 4th Harmonic fo/2/fo/2fo -30 / -34 / -55 dBc Doubler Mode -55 dBc fo/2/fo/2fo -32 / -52 / -58 dBc plls w/ integrated vco - SMT General Description RF Divider Characteristics 19-Bit N-Divider Range (Integer) 19-Bit N-Divider Range (Fractional) Max = 219 - 1 16 524,287 Fractional nominal divide ratio varies (-3 / +3) dynamically max 20 524,283 Synthesizer phase noise can degrade by about 5dB when operating with a reference frequency near the low end of this range. 10 50 200 MHz AC Coupled 1 2 3.3 Vp-p 5 pF REF Input Characteristics Ref Input Frequency Ref Input Range Ref Input Capacitance 14-Bit R-Divider Range 1 16,383 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 0-2 HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz Electrical Specifications (Continued) plls w/ integrated vco - SMT Parameter Condition Min. [1] Typ. Max. Units 0.1 100 MHz 0.1 80 MHz 0.1 125 MHz 2.54 mA Phase Detector (PD) PD Frequency Fractional Feedback Mode PD Frequency Fractional Feedforward Mode (and Register 6 [17:16] = 10) PD Frequency Integer Mode [1] Charge Pump Output Current 0.02 Charge Pump Gain Step Size PD/Charge Pump SSB Phase Noise 20 µA -132 dBc/Hz Input Referred, Maximum CP Current 100 Hz 1 kHz -142 dBc/Hz 10 kHz Add 1 dB for Fractional -151 -149 -147 dBc/Hz 100 kHz Add 3 dB for Fractional -155 -153 -151 dBc/Hz Logic Inputs VIH Output High Voltage DVDD3V-0.4 DVDD3V V VIL Output Low Voltage 0 0.4 V VOH Output High Voltage DVDD3V-0.4 DVDD3V V VOL Output Low Voltage 0 0.4 V 3.5 V Logic Outputs Power Supply Voltages Analog 3.3V Supplies Digital Supply Analog 5V Supplies AVDD, VCCHF, VCCPS, VCCPD, RVDD 3.0 3.3 DVDD3V 3.0 3.3 3.5 V VPPCP, VDDCP, VCC1, VCC2 4.8 5 5.2 V Power Supply Currents +5V Analog Charge Pump VPPCP, VDDCP 5.3 mA VCC1 + VCC2 (fo / 2 / fo / 2fo) 89 / 73 / 72 mA +3.3V Analog AVDD, VCCHF, VCCPS, VCCPD, RVDD 45 mA +3.3V Digital DVDD3V 6.5 mA Power Down - Crystal Off Reg 01h=0, Crystal Not Clocked 10 µA Power Down - Crystal On, 100 MHz Reg 01h=0, Crystal Clocked 100 MHz 10 +5V VCO, PLL Buffer and RF Buffer 200 µA Power on Reset Typical Reset Voltage on DVDD 700 mV 250 µs 10 kHz Offset -91 dBc/Hz 100 kHz Offset -121 dBc/Hz 1 MHz Offset -146 dBc/Hz Min DVDD Voltage for No Reset Power on Reset Delay 1.5 V VCO Open Loop Phase Noise at fo/2 Note 1: This maximum phase detector frequency can only be achieved if the minimum N value is respected. eg. In the case of fractional feedback mode, the maximum PFD rate = fvco/20 or 100 MHz, whichever is less. 0-3 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz Electrical Specifications (Continued) Condition Min. Typ. Max. Units -162 dBc/Hz 100 MHz Offset -163 dBc/Hz -85 dBc/Hz dBc/Hz VCO Open Loop Phase Noise at fo 10 kHz Offset 100 kHz Offset -116 1 MHz Offset -140 dBc/Hz 10 MHz Offset -161 dBc/Hz 100 MHz Offset -166 dBc/Hz dBc/Hz VCO Open Loop Phase Noise at 2fo 10 kHz Offset -80 100 kHz Offset -109 dBc/Hz 1 MHz Offset -135 dBc/Hz 10 MHz Offset -155 dBc/Hz 100 MHz Offset -158 dBc/Hz Closed Loop Phase Noise PLL + VCO at fvco/2 Integer, 100 MHz PD 1 kHz Offset -117 dBc/Hz Integer, 100 MHz PD 10 kHz Offset -121 dBc/Hz Integer, 100 MHz PD 100 kHz Offset -121 dBc/Hz 1 kHz Offset -113 dBc/Hz Fractional, 100 MHz PD 10 kHz Offset -116 dBc/Hz Fractional, 100 MHz PD 100 kHz Offset -117 dBc/Hz 1 kHz Offset -109 dBc/Hz Fractional, 100 MHz PD Closed Loop Phase Noise PLL + VCO at fvco Integer, 100 MHz PD Integer, 100 MHz PD 10 kHz Offset -115 dBc/Hz Integer, 100 MHz PD 100 kHz Offset -112 dBc/Hz Fractional, 100 MHz PD 1 kHz Offset -106 dBc/Hz Fractional, 100 MHz PD 10 kHz Offset -110 dBc/Hz Fractional, 100 MHz PD 100 kHz Offset -114 dBc/Hz 1 kHz Offset -103 dBc/Hz Integer, 100 MHz PD 10 kHz Offset -108 dBc/Hz Integer, 100 MHz PD 100 kHz Offset -107 dBc/Hz dBc/Hz plls w/ integrated vco - SMT Parameter 10 MHz Offset Closed Loop Phase Noise PLL + VCO at 2fo Integer, 100 MHz PD Fractional, 100 MHz PD 1 kHz Offset -100 Fractional, 100 MHz PD 10 kHz Offset -104 dBc/Hz Fractional, 100 MHz PD 100 kHz Offset -106 dBc/Hz Integer Mode Measured w/ 50 MHz PD at 30 kHz Offset -229 dBc/Hz Fractional Mode Measured w/ 50 MHz PD at 30 kHz Offset -227 dBc/Hz Synthesizer Figure of Merit Normalized 1 Hz Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 0-4 HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz Typical Closed Loop Fractional Phase Noise [1] Closed Loop Integer Phase Noise -70 4400MHz PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) -90 2200MHz -110 -130 1100MHz -150 -170 1000 4 10 5 6 10 10 FREQUENCY OFFSET(Hz) 7 10 -110 -150 4 5 10 6 10 7 10 8 10 10 Typical Tuning Curves vs. Switch Position 1100 -20 fmax -40 n0 1050 -60 1102MHz KVCO (MHz/V) 2193MHz -80 4377MHz -100 -120 -140 fmax 1000 n2 n4 n6 n8 n10 n12 n14 n16 n18 n20 n22 n24 n26 950 fmin -160 -180 3 10 4 10 5 6 10 7 10 10 0 -110 100 kHz Offset -120 +27C +85C -40C -130 -140 1 MHz Offset -150 10 MHz Offset -160 -170 2100 2150 2200 2250 2300 FREQUENCY (MHz) 2350 1 2 3 TUNING VOLTAGE (V) 4 5 Typical VCO Tuning Voltage After Calibration 2400 2450 TUNE VOLTAGE AFTER CALIBRATION (V) Free Running VCO Phase Noise Over Temperature n30 n31 900 8 10 OFFSET FREQUENCY (Hz) PHASE NOISE (dBc/Hz) 1102MHz -130 FREQUENCY OFFSET (Hz) 0 2050 4377MHz 2193MHz -90 -170 1000 8 10 Free Running Phase Noise PHASE NOISE (dBc/Hz) plls w/ integrated vco - SMT -70 5 4 fmax fmin 3 31 15 0 2 1 0 2000 2100 2200 2300 2400 2500 VCO FREQUENCY [1] Fractional Mode, 100 MHz Crystal, R=1 0-5 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz Typical VCO Sensitivity vs. Cap @ Fo Voltage Typical Spurious @ 200 kHz from Integer Boundary 0 PHASE NOISE (dBc/Hz) Tuning Cap 0, 2458MHz at 2V 50 KVCO (MHz/V) -20 Tuning Cap 15, 2200MHz at 2V 40 Tuning Cap 31, 2032MHz at 2V 30 Typ Operating Range 20 2 3 TUNING VOLTAGE (V) 4 -100 -120 Fundamental -40C 10 27C 5 Doubler 85C 0 -5 -10 1000 2000 4 10 5 6 7 8 10 10 10 FREQUENCY OFFSET (Hz) 10 Figure of Merit 20 Divide by 2 1000 5 3000 OUTPUT FREQUENCY(MHz) 4000 5000 NORMALIZED PHASE NOISE (dBc/Hz) 1 Typical Output Power Narrow Band Match OUTPUT POWER (dBm) 100MHz, -99dBc -80 -160 +25C 0 15 200kHz, -76dBc 400kHz, -75Bc -60 -140 10 0 -40 2200.200MHz 100MHz PFD Fractional Mode 200kHz Offset from Integer Boundary 70kHz Loop Bandwidth plls w/ integrated vco - SMT 60 -200 -210 Typ FOM vs Offset -220 FOM Floor FOM 1/f Noise -230 -240 100 1000 4 10 5 10 6 10 FREQUENCY OFFSET (Hz) Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 0-6 HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz plls w/ integrated vco - SMT Pin Descriptions Pin Number Function Description 1 AVDD DC Power Supply for analog circuitry. 2, 5, 6, 8, 9, 11 - 14, 18 - 22, 24, 26, 34, 37, 38 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. Power Supply for charge pump analog section 3 VPPCP 4 CP Charge Pump Output 7 VDDCP Power Supply for the charge pump digital section 10 RVDD Reference Supply 15 XREFP Reference Oscillator Input 16 DVDD3V DC Power Supply for Digital (CMOS) Circuitry 17 CEN Chip Enable. Connect to logic high for normal operation. 23 VTUNE VCO Varactor. Tuning Port Input. 25 VCC2 VCO Analog Supply 2 27 VCC1 VCO Analog Supply 1 28 RF_N [1] RF Positive Output 29 [1] 30 RF_P SEN RF Negative Output PLL Serial Port Enable (CMOS) Logic Input 31 SDI PLL Serial Port Data (CMOS) Logic Input 32 SCK PLL Serial Port Clock (CMOS) Logic Input 33 LD_SDO Lock Detect, or Serial Data, or General Purpose (CMOS) Logic Output (GPO) 35 VCCHF DC Power Supply for Analog Circuitry 36 VCCPS DC Power Supply for Analog Prescaler 39 VCCPD DC Power Supply for Phase Detector 40 BIAS External bypass decoupling for precision bias circuits. Note: 1.920V ±20mV reference voltage (BIAS) is generated internally and cannot drive an external load. Must be measured with 10GΩ meter such as Agilent 34410A, normal 10MΩ DVM will read erroneously. [1] For doubler mode of operation, pin 28 (RF_N) and pin 29 (RF_P) outputs must be shorted together. 0-7 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC839LP6CE v03.1211 Absolute Maximum Ratings AVDD, RVDD, DVDD3V, VCCPD, VCCHF, VCCPS -0.3V to +3.6V VPPCP, VDDCP, VCC1 -0.3V to +5.8V VCC2 -0.3V to +5.5V Operating Temperature -40°C to +85°C Storage Temperature -65°C to 125°C Maximum Junction Temperature 125 °C Thermal Resistance (RTH) (junction to ground paddle) 20 °C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Reflow Soldering Peak Temperature 260°C Time at Peak Temperature 40 sec ESD Sensitivity (HBM) Class 1B Outline Drawing plls w/ integrated vco - SMT FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating Package Marking [1] HMC839LP6CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 H839 XXXX [1] 4-Digit lot number XXXX Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 0-8 HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz plls w/ integrated vco - SMT Evaluation PCB, fo & fo/2 Modes The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Evaluation PCB Schematic To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC839LP6CE from the “Search by Part Number” pull down menu to view the product splash page. 0-9 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz [1] Item Description J1, J2 PCB Mount SMA RF Connector J3 Dual Row Terminal Strip J4 - J6 Connector Header C1, C15 - C17, C25 10 µF Capacitor, 0805 Pkg. C2, C3, C6, C7, C11, C12, C14, C18, C27, C43, C45 0.47 µF Capacitor, 0402 Pkg. C4, C13 22 pF Capacitor, 0402 Pkg. C5, C33 1000 pF Capacitor, 0402 Pkg. C8 3.9 pF Capacitor, 0402 Pkg. C19 - C24, C28, C30, C32, C34 0.1 µF Capacitor, 0402 Pkg. C26 1 µF Capacitor, 0603 Pkg. C29 47 pF Capacitor, 0402 Pkg. C35 3300 pF Capacitor, 0402 Pkg. C36 270 pF Capacitor, 0402 Pkg. C37, C38 68 pF Capacitor, 0402 Pkg. C39 - C42, C44 4.7 µF Tantalum Capacitor, 0805 Pkg R1, R2, R5, R8, R11, R15, R18, R19, R21, R24 0 Ohm Resistor, 0402 Pkg. R3, R4 1 Ohm Resistor, 0402 Pkg. R6, R7 0 Ohm Resistor, 0805 Pkg. R12, R20, R29 51 Ohm Resistor, 0402 Pkg. R22, R25 20 kOhm Resistor, 0402 Pkg. R26 - R28 1k Ohm Resistor, 0402 Pkg. L1 3.9 nH Inductor, 0402 Pkg. TP3, TP4 Test Point PC Compact SMT U1 HMC839LP6CE PLL with Integrated VCO U2 HMC860LP3E Low Noise Quad Linear Regulator Y1 3.3V, 50 MHz VCXO Crystal Oscillator PCB [2] 125998 Evaluation Board plls w/ integrated vco - SMT List of Materials for Evaluation PCB 129513, fo & fo/2 Modes [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 0 - 10 HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz plls w/ integrated vco - SMT Evaluation PCB, 2xfo Mode The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Evaluation PCB Schematic To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC839LP6CE from the “Search by Part Number” pull down menu to view the product splash page. 0 - 11 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC839LP6CE v03.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO 1050 -1205, 2100 - 2410, 4200 - 4820 MHz [1] Item Description J1, J2 PCB Mount SMA RF Connector J3 Dual Row Terminal Strip J4 - J6 Connector Header C1, C15 - C17, C25 10 µF Capacitor, 0805 Pkg. C2, C3, C6, C7, C11, C12, C14, C18, C27, C43, C45 0.47 µF Capacitor, 0402 Pkg. C4, C13 22 pF Capacitor, 0402 Pkg. C5, C33 1000 pF Capacitor, 0402 Pkg. C8 8.2 pF Capacitor, 0402 Pkg. C19 - C24, C28, C30, C32, C34 0.1 µF Capacitor, 0402 Pkg. C26 1 µF Capacitor, 0603 Pkg. C29 1 pF Capacitor, 0402 Pkg. C31 0.7 pF Capacitor, 0402 Pkg. C35 3300 pF Capacitor, 0402 Pkg. C36 270 pF Capacitor, 0402 Pkg. C37, C38 68 pF Capacitor, 0402 Pkg. C39 - C42, C44 4.7 µF Tantalum Capacitor, 0805 Pkg C46 27 pF Capacitor, 0402 Pkg. C47 47 pF Capacitor, 0402 Pkg. R1, R2, R8, R11, R15, R18, R19, R21, R24 0 Ohm Resistor, 0402 Pkg. R3, R4 1 Ohm Resistor, 0402 Pkg. R12, R20, R29 51 Ohm Resistor, 0402 Pkg. R13, R14, R30 220 kOhm Resistor, 0402 Pkg. R22, R25 20 kOhm Resistor, 0402 Pkg. R26 - R28 1 kOhm Resistor, 0402 Pkg. R31 0 Ohm Resistor, 0201 Pkg. R32, R33 0 Ohm Resistor, 0805 Pkg. L1 15 nH Inductor, 0402 Pkg. L2, L3 47 nH Inductor, 0402 Pkg. L4 0 Ohm Resistor, 0402 Pkg. TP3, TP4 Test Point PC Compact SMT U1 HMC839LP6CE PLL with Integrated VCO U2 HMC860LP3E Low Noise Quad Linear Regulator Y1 3.3V, 50 MHz VCXO Crystal Oscillator PCB [2] 127729 Evaluation Board plls w/ integrated vco - SMT List of Materials for Evaluation PCB 129514, 2xfo Mode [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 0 - 12 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC839LP6CE HMC839LP6CETR 129023-HMC839LP6CE 129022-HMC839LP6CE 129514-HMC839LP6CE 129513-HMC839LP6CE