REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
Changes in accordance with N.O.R. 5962-R238-93.
93-09-30
M. A. FRYE
B
Drawing being updated to reflect current requirements. - ro
01-03-15
R. MONNIN
REV
SHEET
REV
SHEET
REV STATUS
REV
B
B
B
B
B
B
B
B
B
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
PMIC N/A
PREPARED BY
RICK C. OFFICER
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
CHECKED BY
CHARLES E. BESORE
APPROVED BY
MICHAEL A. FRYE
DRAWING APPROVAL DATE
93-09-15
REVISION LEVEL
B
MICROCIRCUIT, LINEAR, PRECISION, LOW
POWER, LOW VOLTAGE, OPERATIONAL
AMPLIFIER, MONOLITHIC SILICON
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
1 OF
5962-89896
9
5962-E176-01
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-89896
01
~
~
~
~
P
~
~
~
~
Drawing number
X
~
~
~
~
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
~
~
~
~
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
Generic number
01
Circuit function
OP90A
Precision, low power, low voltage.
operational amplifier
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
P
2
Descriptive designator
Terminals
GDIP1-T8 or CDIP2-T8
CQCC1-N20
8
20
Package style
Dual-in-line
Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Supply voltage (VS) ................................................................r18 V dc
Input voltage ...........................................................................[(-VS) – 20 V] to [(+VS) + 20 V]
Differential input voltage .........................................................[(-VS) – 20 V] to [(+VS) + 20 V]
Power dissipation (PD) ...........................................................500 mW
Output short-circuit duration ...................................................Continuous
Storage temperature range .....................................................-65qC to +150qC
Lead temperature range (soldering, 60 seconds) ...................+300qC
Junction temperature (TJ) .......................................................-65qC to +150qC
Thermal resistance, junction-to-case (TJC) .............................See MIL-STD-1835
Thermal resistance, junction-to-ambient (TJA):
Case P ................................................................................+119qC/W
Case 2 .................................................................................+120qC/W
1.4 Recommended operating conditions.
Supply voltage (VS) ................................................................r1.5 V dc to r15 V dc
Source resistance (RS) ...........................................................50 :
Ambient operating temperature range (TA) ............................-55qC to +125qC
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-89896
A
REVISION LEVEL
B
SHEET
2
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed
in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in
the solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-89896
A
REVISION LEVEL
B
SHEET
3
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
-55qC d TA d +125qC
unless otherwise specified
Group A
subgroups
Device
type
1
01
Limits 2/
Min
Input offset voltage
VOS
2,3
Input offset current
IOS
1
VCM = 0 V
01
2,3
Input bias current
+IB
1
VCM = 0 V
01
2,3
-IB
1
VCM = 0 V
2,3
Supply current
ISY
VS = r1.5 V, no load
1
VS = r15 V, no load
Power supply rejection
ratio
PSRR
VS = r1.5 V, r15 V
01
en
2,3
25
1
20
2,3
30
1
Input voltage range 4/
IVR
VS = r15 V, fO = 50 Hz 3/
4
01
01
4
PV
nA
nA
PA
r5.6
r10.0
PV/V
75
nV /
TA = +25qC
Hz
1
+VS = +5 V, -VS = 0 V
VS = r15 V
Large-signal voltage gain
Max
r150
r400
r3
r5
r15
r20
r15
r20
15
2,3
Input noise voltage
density
Unit
AVO
VS = r15 V, VO = r10 V,
VS = r15 V, VO = r10 V,
RL = 10 k:
0 to
+4
2,3
0 to
+3.5
1,2,3
-15 to
+13.5
4
RL = 100 k:
01
01
V
700
5,6
225
4
350
5,6
125
V/mV
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-89896
A
REVISION LEVEL
B
SHEET
4
TABLE I. Electrical performance characteristics – Continued.
Test
Large-signal voltage gain
Symbol
Conditions 1/
-55qC d TA d +125qC
unless otherwise specified
AVO
VS = r15 V, VO = r10 V,
Group A
subgroups
Device
type
4
01
RL = 2 k:
+VS = 5 V, -VS = 0 V,
VO = 1 V, 4 V, RL = 100 k:
+VS = 5 V, -VS = 0 V,
VO = 1 V, 4 V, RL = 10 k:
Output voltage swing
VO
VS = r15 V, RL = 10 k:
Min
125
5,6
50
4
200
5,6
100
4
100
5,6
50
2,3
r14
r13.5
r11
r10.5
1
4.0
2,3
3.9
1
01
2,3
VS = r15 V, RL = 2 k:
VOH
1
+VS = +5 V, -VS = 0 V,
RL = 2 k:
VOL
Limits 2/
1,2,3
+VS = +5 V, -VS = 0 V,
Unit
Max
V/mV
V
500
PV
RL = 10 k:
Common mode rejection
mode
CMRR
1
+VS = +5 V, -VS = 0 V,
01
90
dB
VCM = 0 V, 4 V
+VS = +5 V, -VS = 0 V,
2,3
85
1
100
2,3
95
VCM = 0 V, 3.5 V
VS = r15 V,
VCM = -15 V, 13.5 V
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-89896
A
REVISION LEVEL
B
SHEET
5
TABLE I. Electrical performance characteristics – Continued.
Test
Slew rate
Symbol
Conditions 1/
-55qC d TA d +125qC
unless otherwise specified
+SR
VS = r15 V, rising edge,
Group A
subgroups
Device
type
7
01
Limits 2/
Min
5
Unit
Max
V/ms
no load, AV = 1,
VOUT = -10 V to +10 V,
measured from –5 V to +5 V,
TA = +25qC
-SR
VS = r15 V, falling edge,
5
no load, AV = 1,
VOUT = +10 V to -10 V,
measured from +5 V to -5 V,
TA = +25qC
Input offset voltage
temperature coefficient
1/
TCVOS
VS = r15 V, RS = 50 :,
8
r2.5
01
PV/qC
TA = -55qC, +125qC
Unless otherwise specified, VS = r1.5 V, r15 V, and RS = 50 :.
2/
The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative
current shall be defined as conventional current flow out of a device terminal.
3/
If not tested, shall be guaranteed to the limits specified in table I herein.
4/
IVR guaranteed by CMRR test.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For
packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the
option of not marking the "5962-" on the device.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
appendix A.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-89896
A
REVISION LEVEL
B
SHEET
6
Device type
01
Case outlines
P
2
Terminal
number
1
Terminal symbol
VOSNULL
NC
2
-INPUT
VOSNULL
3
+INPUT
NC
4
-VS
NC
5
VOSNULL
-INPUT
6
OUTPUT
NC
7
+VS
+INPUT
8
NC
NC
9
---
NC
10
---
-VS
11
---
NC
12
---
NC
13
---
NC
14
---
NC
15
---
OUTPUT
16
---
NC
17
---
+VS
18
---
NC
19
---
NC
20
---
VOSNULL
NC = No connection
FIGURE 1. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-89896
A
REVISION LEVEL
B
SHEET
7
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a.
Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
test method 1015 of MIL-STD-883.
(2) TA = +125qC, minimum.
b.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of
MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a.
Tests shall be as specified in table II herein.
b.
Subgroups 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.
4.3.2 Groups C and D inspections.
a.
End-point electrical parameters shall be as specified in table II herein.
b.
Steady-state life test conditions, method 1005 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in test method 1005 of MIL-STD-883.
(2)
TA = +125qC, minimum.
(3)
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-89896
A
REVISION LEVEL
B
SHEET
8
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements
Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004)
1
Final electrical test parameters
(method 5004)
1*,2,3
Group A test requirements
(method 5005)
1,2,3,4,5,6,7,8
Groups C and D end-point
electrical parameters
(method 5005)
1
* PDA applies to subgroup 1.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a
contractor-prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application
requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for
coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962)
should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone
(614) 692-0674.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MILHDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted
by DSCC-VA.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-89896
A
REVISION LEVEL
B
SHEET
9
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 01-03-15
Approved sources of supply for SMD 5962-89896 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next
dated revision of MIL-HDBK-103 and QML-38535.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8989601PA
24355
OP90AZ/883
5962-89896012A
24355
OP90ARC/883
1/ The lead finish shown for each PIN representing a
hermetic package is the most readily available from the
manufacturer listed for that part. If the desired lead finish
is not listed contact the vendor to determine its availability.
2/ Caution. Do not use this number for item acquisition.
Items acquired to this number may not satisfy the
performance requirements of this drawing.
Vendor CAGE
number
24355
Vendor name
and address
Analog Devices
Route 1 Industrial Park
P.O. Box 9106
Norwood, MA 02062
Point of contact: 1500 Space Park Drive
P.O. Box 58020
Santa Clara, CA 95050-8020
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
