AD1988B

High Definition Audio SoundMAX® Codec AD1988A/AD1988B FEATURES Ten 192 kHz DACs Five independent stereo DAC pairs 7.1 surround sound plus independent headphone Independent 8 kHz, 11.025 kHz, 16 kHz, 22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, and 192 kHz sample rates Selectable stereo mixer on outputs 16-, 20-, and 24-bit PCM resolution Six 192 kHz ADCs Three independent stereo ADC pairs Simultaneous record of up to three stereo channels Support for quad microphone arrays plus independent capture channel Independent 8 kHz, 11.025 kHz, 16 kHz, 22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, and 192 kHz sample rates 16-, 20-, and 24-bit resolution S/PDIF output 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, and 192 kHz sample rates 16-, 20-, and 24-bit data widths PCM, WMA/PRO, Dolby®, AC3, and DTS® formats Digital PCM gain control Digital PCM ADC/stream mixer S/PDIF input 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, and 192 kHz sample rates 16-, 20-, and 24-bit data widths PCM, WMA/PRO, Dolby, AC3, and DTS formats Digital PCM gain control Auto synchronizes to source High quality stereo CD input with GND sense MONO_OUT pin for internal speakers or telephony Retasking jack support ENHANCED FEATURES Three stereo headphone amps AD1988A: Windows Vista™ Operating System Premium Logo compliant 95 dB outputs 90 dB audio inputs AD1988B: Windows Vista Premium Logo compliant and Dolby Master Studio™ compliant 101 dB outputs 92 dB audio inputs Internal 32-bit arithmetic for greater accuracy Impedance and presence detection on all jacks Analog PCBEEP and digital synthesis BEEP C/LFE channel swap Two general-purpose digital I/O (GPIO) pins 3.3 V analog and digital supplies Reduced support components Advanced power management modes 48-pin LQFP and LFCSP_VQ package options, Pb-free Supports Andrea Active Noise Reduction headphones Hardware volume control Built-in microphone gain amps Adjustable microphone bias pins Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. AD1988A/AD1988B TABLE OF CONTENTS Features .............................................................................................. 1 Enhanced Features............................................................................ 1 Revision History ............................................................................... 2 Functional Block Diagram .............................................................. 3 Specifications..................................................................................... 4 Test Conditions............................................................................. 4 Absolute Maximum Ratings............................................................ 7 Thermal Resistance ...................................................................... 7 ESD Caution.................................................................................. 7 Pin Configuration and Function Descriptions..............................8 Clarification of Output Configurations .................................. 11 HD Audio Widgets......................................................................... 12 Jack Presence Detection................................................................. 18 HD Audio Style Jack Presence Detection ............................... 18 Hardware Volume Control............................................................ 19 Outline Dimensions ....................................................................... 20 Ordering Guide .......................................................................... 20 REVISION HISTORY 10/06—Revision 0: Initial Version Rev. 0 | Page 2 of 20 AD1988A/AD1988B FUNCTIONAL BLOCK DIAGRAM N ID : 0 7 N ID : 1 C AVSS +3.3V +/-5% AVDD S/PDIF I n / GPIO_1 MIC Bias Regulator N ID : 3 5 Po w e r Co ntrol 24 bit 32-192 k Hz PCM / D igital S/PDIF R X Digital GAM Inpu t_En -34 .5 to + 12 dB Z GPIO_1 MIC_BIAS_FILT Stereo Paths Mono Paths N ID : 1 D 0 (01 ) N ID : 0 2 M Σ M 1 (0 B ) 24 bit 32-192 kHz PCM / D igital S/PDIF T X N ID : 1 B Digital AM -58 .5 to 0 dB Z Output_En S/PDIF Out VREF N ID : 2 3 Pow e r Co ntrol VREF_FILT 101+ dB (AD1988B) 24 bit 192 kHz PCM Σ∆ D AC DAC _ 4 N ID : 0 A D i g i ta l 0 (0 A ) A -58 .5 to 0 dB 1 (21 ) M N ID : 2 8 N ID : 2 5 Σ M M Z Split-Z EN PORT -H Surround Center 24 bit 192 kHz PCM Σ∆ D AC DAC _ 3 N ID : 0 6 D i g i ta l 0 (06 ) N ID : 2 A N ID : 1 6 BIAS M Z PORT -F MIC BIAS A -58 .5 to 0 dB 1 (21 ) Σ M M Z PORT -F Surround Back 24 bit 192 kHz PCM Σ∆ D AC DAC _ 2 N ID : 0 5 D i g i ta l 0 (05 ) Boost NID: 3B M N ID :2 7 EN A -58 .5 to 0 dB 1 (21 ) N ID : 2 4 Σ M M Z S WA P PORT -G Center / LFE EN N ID : 1 2 DAC _ 1 N ID : 0 4 D i g i ta l 0 (04 ) H D A U D I O SDI SDO SYNC R ESET# BITCLK 24 bit 192 kHz PCM Σ∆ D AC BIAS / EAPD M N ID : 2 9 Z PORT -D MIC BIAS / EAPD A Σ -58 .5 to 0 dB M HP AMP Z PORT -D HP-Front L/R 24 bit 192 kHz PCM Σ∆ D AC DAC _ 0 N ID : 0 3 D i g i ta l Mixer Power Control N ID : 1 9 1 (21 ) M Boost NID: 3D EN A -58 .5 to 0 dB N ID : 2 1 AM -46 .5 to 0 dB 0 (03 ) 1 (04 ) 3 :1 2 (06 ) 0 (37 ) N ID : 1 1 BIAS M N ID : 2 2 Z PORT -A MIC BIAS GPIO_1 NID: 20 GPIO_0 / Volume 5 (3 B – P or t- F) 3 (3 D – P or t- D ) Σ N ID : 3 7 1 (21 ) M I N T E R F A C E GPIO HP AMP Z PORT -A Headphone M Boost NID: 38 -34.5 to +12dB HW Volume Control N ID : 1 F N ID : 3 3 EN GAM GAM GAM 2 (38 – P or t- A ) 0 (03 ) 1 (04 ) 3 :1 2 (06 ) 2 (24 ) N ID : 3 6 1 (25 ) 0 (3 A ) 1 (21 ) 0 (36 ) M N ID : 1 E N ID : 2 D N ID : 1 3 Σ M Σ S te r e o D own-M ix A -46 .5 to 0 dB M MONO_OUT 5 3 2 GAM 1 4 0 1 (33 – P or t- C /H /G) 3 :1 Σ 6 7 N ID : 1 4 N ID : 3 4 2 (24 ) 1 (25 ) 0 (3 C ) N ID : 3 0 0 (03 ) 1 (04 ) 2 (06 ) BIAS 0 (30 ) Z PORT -B MIC BIAS GAM 4 (34 – P or t- E /H /G) 3 :1 3 :1 M N ID : 2 B Σ 1 (21 ) M HP AMP Z PORT -B Microphone GAM GAM 7 (1 A - P CB e e p) M Boost NID: 39 EN GAM 0 (39 – P or t- B ) 6 (1 8 - C D ) N ID : 0 B Selector 3 :1 2 (0 F) 1 (0 9 ) 0 (0 8 ) N ID : 1 7 ADC _ 0 N ID : 0 8 ADC SE L_ 0 N ID : 0 C 1 (21 ) BIAS M N ID : 2 6 Z PORT -E MIC BIAS S WA P 24 bit 192 kHz PCM Σ∆ ADC D i g i ta l / A na l o g GM -58 .5 to + 22 .5 dB Selector 10 :1 0 (05 ) 1 (04 ) N ID : 3 2 2 :1 0 (32 ) Σ M M Z PORT -E MIC 1/2 Boost NID: 3C EN N ID : 1 5 +1.5V + /- 10 % DVIO (A D 1988L15 ) ADC _ 1 N ID : 0 9 ADC SE L_ 1 N ID : 0 D 1 (21 ) M N ID : 2 C BIAS / EAPD Z PORT -C MIC BIAS / EAPD PORT -C +3.3V + /- 10 % (A D 1988L33 ) DVDD +3.3V + /- 10 % 24 bit 192 kHz PCM Σ∆ ADC D i g i ta l / A na l o g GM -58 .5 to + 22 .5 dB Selector 10 :1 0 (04 ) 1 (0 A ) N ID : 3 1 2 :1 0 (31 ) Σ M Boost NID: 3A M Z Line In EN DVFILT +1.8V +5% -20 % 9 (20 - M ixe r ) 7 (25 – P or t- H ) ADC _ 2 N ID : 0 F ADC SE L_ 2 N ID : 0 E 6 (24 – P or t- G) 3 (3 B – P or t- F) 8 (3 D – P or t- D ) Selector 10 :1 0 (38 – P or t- A ) 1 (39 – P or t- B ) 4 (3 C – P or t- E ) N ID : 1 8 CD D i ff Amp PCBeep N ID : 1 A DVSS N ID : 1 0 24 bit 192 kHz PCM Σ∆ ADC D i g i ta l / A na l o g Digital Beep AM -45 .0 t o 0 d B 3 d B S tep s GM -58 .5 to + 22 .5 dB 5 (18 - CD ) CD _L CD _GND CD _R Figure 1. Block Diagram Rev. 0 | Page 3 of 20 05843-011 2 (3 A – P or t- C ) AD1988A/AD1988B SPECIFICATIONS TEST CONDITIONS Test Conditions for the AD1988A and AD1988B are as follows, unless otherwise noted. Analog Input/Output Conditions Temperature at 25°C Digital supply (DVDD) at 3.3 V ±10% Analog supply (AVDD) at 3.3 V ±5% MIC_BIAS_FILT at 5.0 V ±5% Sample rate (FS) at 48 kHz Input signal at 1008 Hz Analog output pass band at 20 Hz to 20 kHz Table 1. DAC Conditions Calibrated Output −3 dB relative to full scale 10 kΩ output load: line out tests 32 Ω output load: headphone tests ADC Conditions Calibrated 0 db PGA gain Input −3.0 dB relative to full scale Typ AD1988A/ AD1988B Max Parameter DIGITAL DECIMATION AND INTERPOLATION FILTERS 1 Pass Band Pass-Band Ripple Stop Band Stop Band Rejection Group Delay Group Delay Variation over Pass Band ANALOG-TO-DIGITAL CONVERTERS Resolution1 Gain Error Interchannel Gain Mismatch ADC Offset Error ADC Crosstalk1 Line Inputs LINE_IN to Other DIGITAL-TO-ANALOG CONVERTERS Resolution1 Gain Error Interchannel Gain Mismatch Total Out-of-Band Energy 1 DAC Crosstalk1 DAC VOLUMES—PROGRAMMABLE GAIN ATTENUATOR Step Size Output Gain/Attenuation Range ADC VOLUMES—PROGRAMMABLE GAIN AMPLIFIER/ATTENUATOR Step Size PGA Gain/Attenuation Range ANALOG MIXER—PROGRAMMABLE GAIN AMPLIFIER/ATTENUATOR Signal-to-Noise Ratio (SNR)1, 2 Step Size Input Gain/Attenuation Range Conditions/Comments fS 8 kHz ~ 192 kHz Min 0 0.60 fS Unit 20 0 24 Full-scale span relative to nominal input voltage Difference of gain errors 0.40 fS Hz ±0.005 dB Hz −100 dB 1/fS μs Bits % dB mV dB −80 dB Bits % dB dB dB ±10 ±0.2 ±0.5 ±5 Input L, Ground R, Read R; Input R, Ground L, Read L −85 −100 24 Full-scale span relative to nominal input voltage Difference of gain errors To 100 kHz Input L, Zero R, Read R; Input R, Zero L, Read L DAC_0, DAC_1, DAC_2, DAC_3, DAC_4 −58.5 ±10 ±0.2 −85 −95 ±0.5 +1.5 0 dB dB ADCSEL_0, ADCSEL_1, ADCSEL_2 −58.5 +1.5 +22.5 dB dB Input to output (including CD in) All mixer inputs All mixer inputs Rev. 0 | Page 4 of 20 95/96 +1.5 −34.5 +12.0 dB dB AD1988A/AD1988B Typ AD1988A/ AD1988B Max Parameter ANALOG LINE LEVEL OUTPUTS Full-Scale Output Voltage PORT-C, PORT-E, PORT-F, PORT-G, PORT-H, and MONO_OUT Output Impedance1 External Total Load Impedance Output Capacitance1 External Load Capacitance1 Total Harmonic Distortion (THD+N)1 Dynamic Range1 ANALOG HP DRIVE OUTPUTS Full-Scale Output Voltage PORT-A, PORT-B, and PORT-D Output Impedance1 External Load Impedance1 Output Capacitance1 External Load Capacitance1 Total Harmonic Distortion (THD+N)1 Dynamic Range1 ANALOG INPUTS PORT-G, PORT-H, or CD Microphone Boost Amplifiers PORT-A, PORT-B, PORT-C, PORT-D, PORT-E, or PORT-F Conditions/Comments Line out drive enabled When ports are used as line level outputs Min 1.0 2.83 Unit V rms 3 V p-p 300 10 15 1000 −60 dB reference to fS A-weighted Output drive enabled When ports are used as outputs 1.0 2.83 0.5 32 15 1000 10 kΩ load 32 Ω load −60 dB reference to fS A-weighted, 10 kΩ or 32 Ω loads When ports are used as inputs −83/−84 −83/−84 +95/+101 −85/−85 +95/+101 Ω kΩ pF pF dB dB V rms3 V p-p Ω Ω pF pF dB dB dB 1 2.83 0 dB boost +10 dB boost +20 dB boost +30 dB boost 1 2.83 0.316 0.894 0.1 0.283 0.032 0.089 23 60 150 5 −81/−82 +90/+92 +90/+92 2.97 3.3 2.0 0.8 2.4 0.6 3.63 V rms3 V p-p V rms3 V p-p V rms3 V p-p V rms3 V p-p V rms3 V p-p kΩ kΩ kΩ pF dB dB dB V V V V V Input Impedance1 PCBEEP PORT-G, PORT-H All others (with 0 dB boost) Input Capacitance1 ANALOG INPUT PERFORMANCE Total Harmonic Distortion Plus Noise (THD+N)1 Dynamic Range Signal-to-Noise Ratio (SNR)2 STATIC DIGITAL SPECIFICATIONS Digital I/O (DVIO) VIH VIL VOH VOL 7.5 −60 dB in reference to fS A-weighted DVIO @ 3.3 V ± 10% Rev. 0 | Page 5 of 20 AD1988A/AD1988B Typ AD1988A/ AD1988B Max Parameter POWER SUPPLY Analog (AVDD) Power Supply Range Power Dissipation Supply Current Digital (DVDD) Power Supply Range Power Dissipation Supply Current Digital I/O (DVIO) Power Supply Range Power Dissipation Supply Current Power Supply Rejection1 (AVDD) 1 2 Conditions/Comments 3.3 V ± 5% Min Unit 3.13 3.30 155/172 47/52 3.46 V mW mA V mW mA V mW mA dB V 3.3 V ± 10% 2.97 3.30 3.63 247.5/238 75/75 3.30 3.96 1.20 80 3.63 3.3 V ± 10% 2.97 100 mV p-p signal @ 1 kHz Guaranteed, not tested. SNR measurement defined as “the difference in level between a reference output signal and the device output with no signal applied.” This definition is taken from B. Metzler, Audio Measurement Handbook, 1st edition, Audio Precision, Inc., 1993, p. 165. 3 RMS values assume sine wave input. Table 2. Power-Down States Parameter POWER-DOWN STATES FUNCTION Node DAC Pair ADC Pair Mixer Power Control (and Associated Amps) MIC_BIAS RESET Comments D-State D3 D3 D3 D3 D3 AD1988A/AD1988B DIDD Typ AIDD Typ 21/20 6/6 5.3/5.4 0/0 0/0 2.9/2.7 1.2/1.7 5/5.6 3.2/3.1 2.0/2.4 0.5/0.5 3.1/3.4 Unit mA mA mA mA mA mA Powered down saves (each) Powered down saves (each) Saves Powered down saves Low (active) state Rev. 0 | Page 6 of 20 AD1988A/AD1988B ABSOLUTE MAXIMUM RATINGS Table 3. Parameter Digital (DVDD) Digital I/O (DVIO) Analog (AVDD) Input Current (Except Supply Pins) Analog Input Voltage (Signal Pins) Digital Input Voltage (Signal Pins) Ambient Temperature (Operating) Storage Temperature Range Rating −0.30 V to +3.65 V −0.30 V to +3.65 V −0.30 V to +3.65 V ±10.0 mA −0.30 V to AVDD + 0.3 V −0.30 V to DVIO + 0.3 V 0°C to +70°C −65°C to +150°C THERMAL RESISTANCE Ambient temperature ratings are as follows: TAMB = TCASE − (PD × θCA) where: TCASE = case temperature in °C. PD = power dissipation in W. θCA = thermal resistance (case-to-ambient). Table 4. Thermal Resistance Package Type LQFP LFCSP_VQ4 1 2 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. θJA1 48 47 θJC2 17 15 θCA3 31 32 Unit ºC/W ºC/W θJA = thermal resistance: junction-to-ambient. θJC = thermal resistance: junction-to-case. 3 θCA = thermal resistance: case-to-ambient. 4 VQ = very thin quad. ESD CAUTION Rev. 0 | Page 7 of 20 AD1988A/AD1988B PIN CONFIGURATION AND FUNCTION DESCRIPTIONS S/PDIF-OUT S/PDIF-IN/GPIO_1 PORT-H_R PORT-H_L PORT-G_R PORT-G_L AVSS PORT-A_R MONO_OUT PORT-A_L AVDD MIC_BIAS-A S/PDIF-IN/GPIO_1 48 47 46 45 44 43 42 41 40 39 38 37 48 47 46 45 44 43 42 41 40 39 38 37 36 PORT-D_R DVCORE 1 DVCORE GPIO_0/VOLUME 1 2 PIN 1 INDICATOR DVI/O 3 DVSS 4 SDATA_OUT 5 BIT_CLK 6 DVSS 7 SDATA_IN 8 DVDD 9 SYNC 10 RESET 11 PCBEEP 12 AD1988A/AD1988B TOP VIEW (Not to Scale) 36 35 34 33 32 31 30 29 28 27 26 25 PORT-D_R PORT-D_L SENSE_B/SRC_A MIC_BIAS_FILT MIC_BIAS/EAPD-D MIC_BIAS-E MIC_BIAS-F MIC_BIAS/EAPD-C MIC_BIAS-B VREF_FILT AVSS AVDD GPIO_0/VOLUME 2 DVI/O 3 DVSS 4 SDATA_OUT 5 PIN 1 MIC_BIAS-A 35 PORT-D_L 34 SENSE_B/SRC_A 33 MIC_BIAS_FILT 32 MIC_BIAS/EAPD-D 31 MIC_BIAS-E 30 MIC_BIAS-F 29 MIC_BIAS/EAPD-C 28 MIC_BIAS-B 27 VREF_FILT 26 AVSS 25 AVDD MONO_OUT S/PDIF-OUT PORT-G_R PORT-H_R PORT-A_R PORT-G_L PORT-H_L PORT-A_L PORT-B_R AD1988A/AD1988B TOP VIEW (Not to Scale) BIT_CLK 6 DVSS 7 SDATA_IN 8 DVDD 9 SYNC 10 RESET 11 PCBEEP 12 13 14 15 16 17 18 19 20 21 22 23 24 13 14 15 16 17 18 19 20 21 22 23 24 PORT-E_R PORT-F_R PORT-E_L PORT-F_L AVDD PORT-C_L AVSS SENSE_A/SRC_B PORT-E_L PORT-E_R PORT-F_L PORT-F_R CD_L CD_GND CD_R PORT-B_L PORT-B_R PORT-C_L PORT-C_R SENSE_A/SRC_B PORT-C_R PORT-B_L CD_L CD_GND CD_R Figure 2. LFCSP_VQ Pin Configuration Figure 3. LFQP Pin Configuration Table 5. Pin Function Descriptions Mnemonic DVCORE GPIO_0/VOLUME DVIO DVSS SDATA_OUT BIT_CLK SDATA_IN DVDD SYNC RESET PCBEEP SENSE_A/SRC_B PORT-E_L, PORT-E_R Pin Number 1 2 3 4, 7 5 6 8 9 10 11 12 13 14, 15 I/O O I/O I I I O I/O I I I I I/O I/O Description Filter Connection for Internal Core Voltage Regulator. This pin must be connected to filter capacitors: 10 μF, 1.0 μF, and 0.1 μF connected in parallel between Pin 1 and DVSS (Pin 4 and Pin 7). General-Purpose Input/Output Pin (Digital I/O). Digital signal used to control external circuitry. Volume Control. When enabled, it can be used as an external volume control Link Digital I/O Voltage Reference. 3.3 V (±10%). Digital Supply Return (Ground). Link Serial Data Output (Digital Interface). AD1988 input stream. Clocked on both edges of the BIT_CLK. Link Bit Clock (Digital Interface). 24.000 MHz serial data clock. Link Serial Data Input (Digital Interface). AD1988 output stream. Clocked only on one edge of BIT_CLK. Digital Supply Voltage 3.3 V ± 10%. This is regulated down to 1.9 V on Pin 1 to supply the internal digital core internal to the AD1988. Link Frame Sync (Digital Interface). 48 kHz frame sync plus SDI stream IDs. Link Reset (Digital Interface). AD1988 master hardware reset. Monaural Input from System for PCBEEP. Line level input. Jack Sense A to Jack Sense D Input/Sense B Drive. Left and Right Rear Panel Stereo Mic In/C/LFE (Analog Input/Output). Input: line level input, supports microphones with MIC_BIAS and boost amplifiers. Output: line level output. Left and Right Rear Panel Stereo Mic In/Surround Rear (Analog Input/Output). Input: line level input, supports microphones with MIC_BIAS and boost amplifiers. Output: line level output only. CD Audio Left Channel, CD Audio Right Channel. CD Audio Analog Ground Reference (for Analog CD Input). Line level input only. Front Panel Stereo Mic In/Front Panel Headphones. Analog input/output. Input: line level input, supports microphones with MIC Bias and boost amplifiers. Output: line level output, capable of driving headphone load and power. Rev. 0 | Page 8 of 20 PORT-F_L, PORT-F_R 16, 17 I/O CD_L, CD_R CD_GND PORT-B_L, PORT-B_R 18, 20 19 21, 22 I I I/O 05843-003 05843-001 AD1988A/AD1988B Mnemonic PORT-C_L, PORT-C_R Pin Number 23, 24 I/O I/O Description Rear Panel Line-In/Surround Back Output. Analog input/output. Input: line level input, supports microphones with MIC Bias and boost amplifiers. Output: line level output only. Analog Supply Voltage. 3.3 V only. Caution: Do not apply 5.0 V to this pin. AVDD supplies should be well regulated and filtered because supply noise degrades audio performance. Analog Supply Return (Ground). AVSS should be connected to DVSS using a conductive trace under, or close to, the AD1988A/AD1988B. Voltage Reference Filter. This pin must be connected to filter capacitors: 1.0 μF and 0.1 μF connected in parallel between Pin 27 and AVSS (Pin 26). Switchable Microphone Bias for PORT-B. Capable of: High-Z, 0 V, 1.65 V, 3.78 V, and 3.95 V (with 5.0 V on Pin 33). High-Z, 0 V, 1.65 V, 2.86 V, and 3.10 V (with 3.3 V on Pin 33). Switchable Microphone Bias for PORT-C. This pin has the same function as MIC_BIAS-B. Switchable Microphone Bias for PORT-F. This pin has the same function as MIC_BIAS-B. Switchable Microphone Bias for PORT-E. This pin has the same function as MIC_BIAS-B. Switchable Microphone Bias for PORT-D. This pin has the same function as MIC_BIAS-B. Filter for Microphone Bias Boost Circuitry. Connect this pin to 5.0 V via a low-pass filter. When connected in this way, the AD1988A/AD1988B are each capable of providing 3.95 V as a microphone bias to all of the MIC_BIAS pins. If 5 V is not available, connect this pin to 3.3 V (AVDD) via a low-pass filter. The AD1988A/AD1988B produce a MIC_BIAS voltage relative to the AVDD supply (typically 3.1 V @ AVDD = 3.3 V). Jack Sense E to Jack Sense H Input/Sense A Drive. Left and Right Rear Panel Headphone (Front Line Out)/Stereo MIC In. Analog input/output. Input: line level input, supports microphones with MIC_BIAS and boost amplifiers. Output: line level output, capable of driving headphone load and power. Switchable Microphone Bias for PORT-A. This pin has the same function as MIC_BIAS-B. Left and Right Front Panel Headphone Output/Stereo MIC In. Analog input/output. Input: line level input, supports microphones with MIC_BIAS and boost amplifiers. Output: line level output, capable of driving headphone load and power. Monaural Output to Internal Speaker or Telephony Subsystem. Line level output only. Left and Right Rear Panel C/LFE Output/Line Input. Input: line level input. Output: line level output. Left and Right Rear Panel Surround Center/Side Output/Line Input. Analog input/output. Input: line level input. Output: line level output. S/PDIF_IN/GPIO Pin. S/PDIF_IN supports S/PDIF input. When enabled, GPIO_1 can be used as a GPIO pin. S/PDIF_OUT. Supports S/PDIF output. AVDD AVSS VREF_FILT MIC_BIAS-B 25, 38 26, 42 27 28 I I O O MIC_BIAS-C MIC_BIAS-F MIC_BIAS-E MIC_BIAS-D MIC_BIAS_FILT 29 30 31 32 33 O O O O I SENSE_B/SRC_A PORT-D_L, PORT-D_R 34 35, 36 I/O I/O MIC_BIAS-A PORT-A_L, PORT-A_R 37 39, 41 O I/O MONO_OUT PORT-G_L, PORT-G_R 40 43, 44 O PORT-H_L, PORT-H_R 45, 46 S/PDIF_IN/GPIO_1 S/PDIF_OUT 47 48 I/O O Rev. 0 | Page 9 of 20 AD1988A/AD1988B Table 6. Pins Grouped by Function Function Digital Interface Pin No. 5 6 8 10 11 48 47 2 13 34 1 27 33 28 29 30 31 32 37 9 3 4, 7 25, 38 26, 42 12 14 15 16 17 18 20 21 22 23 24 35 36 39 40 41 43 44 45 46 Mnemonic SDATA_OUT BIT_CLK SDATA_IN SYNC RESET S/PDIF_OUT S/PDIF_IN/GPIO_1 GPIO_0/VOLUME SENSE_A/SRC_B SENSE_B/SRC_A DVCORE VREF_FILT MIC_BIAS_FILT MIC_BIAS-B MIC_BIAS-C MIC_BIAS-F MIC_BIAS-E MIC_BIAS-D MIC_BIAS-A DVDD DVIO DVSS AVDD AVSS PCBEEP PORT-E_L PORT-E_R PORT-F_L PORT-F_R CD_L CD_R PORT-B_L PORT-B_R PORT-C_L PORT-C_R PORT-D_L PORT-D_R PORT-A_L MONO_OUT PORT-A_R PORT-G_L PORT-G_R PORT-H_L PORT-H_R Digital Input/Output Jack Sense Filter/Reference Microphone Bias Power and Ground Analog Input/Output Rev. 0 | Page 10 of 20 AD1988A/AD1988B CLARIFICATION OF OUTPUT CONFIGURATIONS DAC, ADC, and port assignments are arbitrary; however, ports are optimized for certain configurations. Use the guidelines in Table 7, Table 8, and Table 9 when selecting ports for particular functions. Note the following for each of these tables: In desktop applications with shared input/5.1 jacks, assign the ports as listed in Table 8. Table 8. Shared Input/5.1 Jacks Port PORT-A PORT-B PORT-C PORT-D PORT-E MONO_OUT Function Front Panel Headphone Front Panel Microphone Rear Panel LineIn/Surround-Rear (5.1) Rear Panel Front/Headphone Rear Panel Microphone/C/LFE Internal Mono Speaker (use GPIO as EAPD) HP x x MIC x x x x x LO x x x x x x LI x x x x x • • • • HP is the output capable of driving headphone load and power MIC is input that supports microphones with MIC Bias and boost amplifiers LO is the line level output LI is the line level input x In desktop applications with discreet jacks (the default configuration), assign the ports as listed in Table 7. Table 7. Discreet Jacks (Default Configuration) Port PORT-A PORT-B PORT-C PORT-D PORT-E PORT-F PORT-G PORT-H MONO_OUT Function Front Panel Headphone Front Panel Microphone Rear Panel Line-In Rear Panel Front/Headphone Rear Panel Microphone Rear Panel Surround-Rear (5.1) Rear Panel C/LFE Rear Panel SurroundCenter/Side (7.1) Internal Mono Speaker (use GPIO as EAPD) HP x x x MIC x x x x x x LO x x x x x x x x x LI x x x x x x x x In notebook applications, to support fully retasking jacks, assign the ports as listed in Table 9. Table 9. Port PORT-A PORT-B PORT-D PORT-C Function Headphone Jack Microphone Jack Line-In Jack Internal Stereo Speakers (use GPIO as EAPD) Internal Quad Microphone Array (Optional) HP x x x MIC x x x x LO x x x x LI x x x x PORT-E/PORT-F x x x Rev. 0 | Page 11 of 20 AD1988A/AD1988B HD AUDIO WIDGETS Table 10. Node ID 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2F 30 31 32 33 Name ROOT FUNCTION S/PDIF DAC DAC_0 DAC_1 DAC_2 DAC_3 S/PDIF ADC ADC_0 ADC_1 DAC_4 S/PDIF Mix Selector ADC Selector 0 ADC Selector 1 ADC Selector 2 ADC_2 Digital Beep PORT-A PORT-D MONO_OUT PORT-B PORT-C PORT-F PORT-E CD IN Mixer Power-Down Analog PCBEEP S/PDIF Out S/PDIF In S/PDIF Mixer MONO_OUT Mixer Volume Knob Analog Mixer Mixer Output Attenuator PORT-A Mixer VREF Power-Down PORT-G PORT-H PORT-E Mixer PORT-G Mixer PORT-H Mixer PORT-D Mixer PORT-F Mixer PORT-B Mixer PORT-C Mixer Stereo Mix-Down BIAS Power-Down PORT-B Out Selector PORT-C Out Selector PORT-E Out Selector PORT-C In Selector Type Root Function Audio output Audio output Audio output Audio output Audio output Audio input Audio input Audio input Audio output Audio selector Audio selector Audio selector Audio selector Audio input Beep generator Pin complex Pin complex Pin complex Pin complex Pin complex Pin complex Pin complex Pin complex Power widget Pin complex Pin complex Pin complex Audio mixer Audio mixer Vendor defined Audio mixer Audio selector Audio mixer Vendor defined Pin complex Pin complex Audio mixer Audio mixer Audio mixer Audio mixer Audio mixer Audio mixer Audio mixer Audio mixer Vendor defined Audio selector Audio selector Audio selector Audio selector Description Device identification Designates this device as an audio codec S/PDIF digital stream output interface Stereo headphone channel digital/audio converters Stereo front channel digital/audio converters Stereo C/LFE channel digital/audio converters Stereo surround-back (5.1) channel digital/audio converters S/PDIF digital stream input interface Stereo record Channel 0 audio/digital converters Stereo record Channel 1 audio/digital converters Stereo surround-side (7.1) channel digital/audio converters Selects the ADC to drive the S/PDIF mixer Selects and amplifies/attenuates the input to ADC_0 Selects and amplifies/attenuates the input to ADC_1 Selects and amplifies/attenuates the input to ADC_2 Stereo record Channel 2 audio/digital converters Internal digital PCBEEP signal Front panel headphone jack Rear panel front speaker jack Monaural output pin (internal speakers or telephony system) Front panel microphone jack Rear panel line-in jack Rear panel surround-back (5.1) jack Rear panel microphone jack Analog CD input Powers down the analog mixer and associated amps External analog PCBEEP signal input S/PDIF output pin S/PDIF input pin Mixes the selected ADC with the digital stream to drive S/PDIF out Selects the source that drives the MONO_OUT signal Hardware volume knob Mixes individual gain analog inputs Attenuates the mixer output to drive the port mixers Mixes the DAC_0 and mixer output amps to drive PORT-A Powers down the internal and external VREF circuitry Rear panel C/LFE jack Rear panel surround-side (7.1) jack Mixes the PORT-E selected DAC and mixer output amps to drive PORT-E Mixes the DAC_3 and mixer output amps to drive PORT-G Mixes the DAC_4 and mixer output amps to drive PORT-H Mixes the DAC_1 and mixer output amps to drive PORT-D Mixes the DAC_2 and mixer output amps to drive PORT-F Mixes the PORT-B selected DAC and mixer output amps to drive PORT-B Mixes the PORT-C selected DAC and mixer output amps to drive PORT-C Mixes the stereo L/R channels to drive MONO_OUT Powers down the internal MIC_BIAS_FILT and all MIC_BIAS pins Selects DAC_0, DAC_1, and DAC_3 for PORT-B Selects DAC_2 and DAC_4 for PORT-C Selects DAC_2 and DAC_4 for PORT-E Selects from the PORT-C, PORT-G, and PORT-H inputs to the mixer input Rev. 0 | Page 12 of 20 AD1988A/AD1988B Node ID 34 36 37 38 39 3A 3B 3C 3D Name PORT-E In Selector MONO_OUT Selector PORT-A Out Selector PORT-A Boost PORT-B Boost PORT-C Boost PORT-F Boost PORT-E Boost PORT-D Boost Type Audio selector Audio selector Audio selector Audio selector Audio selector Audio selector Audio selector Audio selector Audio selector Description Selects from the PORT-E, PORT-G, and PORT-H inputs to the mixer input Selects DAC_0, DAC_1, and DAC_3 for MONO_OUT Selects DAC_0, DAC_1, and DAC_3 for PORT-A Microphone boost amp for PORT-A Microphone boost amp for PORT-B Microphone boost amp for PORT-C Microphone boost amp for PORT-F Microphone boost amp for PORT-E Microphone boost amp for PORT-D Table 11. AD1988A Device Root and Function Node Parameters Sub Node Count 0x04 00010001 0002003C Function Group Type 0x05 00000001 Audio Function Group Capabilities 0x08 00010C0C GPIO Capabilities 0x11 40000002 Node ID 00 01 1 Name ROOT FUNCTION Vendor ID 0x00 11D41988 Revision ID 1 0x02 00100400 Silicon revision number may change without prior notice. Number shown is current at the publication date of this document. Table 12. AD1988B Device Root and Function Node Parameters Sub Node Count 0x04 00010001 0002003C Function Group Type 0x05 00000001 Audio Function Group Capabilities 0x08 00010C0C GPIO Capabilities 0x11 40000002 Node ID 00 01 1 Name ROOT FUNCTION Vendor ID 0x00 11D4198B Revision ID 1 0x02 00100300 Silicon revision number may change without prior notice. Number shown is current at the publication date of this document. Rev. 0 | Page 13 of 20 AD1988A/AD1988B Table 13. Widget Parameters Widget Capabilities 09 000004C0 00030311 00000405 00000405 00000405 00000405 00130391 00100501 00100501 00000405 00300301 0030010D 0030010D 0030010D 00100501 0070000C 0040018D 0040018D 0040010C 0040018D 0040018D 0040018D 0040098D 00400001 00500500 00400000 0040030D 0040020B 00200303 00200103 00600080 0020010B 0030010D 00200103 00F00100 0040098D 0040018D 00200103 00200103 00200103 00200103 00200103 00200103 00200103 00200100 00F00100 00300101 00300101 PCM Size, Rate 0A 000E07FF 000E07E0 000E07FF 000E07FF 000E07FF 000E07FF 000E07E0 000E07FF 000E07FF 000E07FF Stream Formats 0B 00000001 00000005 00000001 00000001 00000001 00000001 00000005 00000001 00000001 00000001 Pin Capabilities 0C Input Amp Capabilities 0D 80000000 Con. List Length 0E 00000001 00000000 00000000 00000000 00000000 00000001 00000001 00000001 00000000 00000003 00000007 00000007 00000007 00000001 00000000 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000000 00000002 00000000 00000001 00000000 00000002 00000002 00000000 00000008 00000001 00000002 00000008 00000001 00000001 00000002 00000002 00000002 00000002 00000002 00000002 00000002 00000001 00000006 00000003 00000002 Power States 0F 00000009 00000009 00000009 00000009 00000009 00000009 00000009 00000009 Output Amp Capabilities 12 00052727 00052727 00052727 00052727 00052727 Volume Knob Capabilities 13 Type ID X 0 0 0 0 0 1 1 1 0 3 3 3 3 1 7 4 4 4 4 4 4 4 4 5 4 4 4 2 2 6 2 3 2 F 4 4 2 2 2 2 2 2 2 2 F 3 3 Node ID 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2F 30 31 00052727 80053627 80053627 80053627 000E07FF 00000001 0000373F 0000373F 00000010 0000373F 00003737 00003737 00003737 00000020 00000020 00000010 00000020 00000009 800B0F0F 80000000 80000000 80051F1F 80000000 80000000 80000000 80000000 00000009 80052727 80051F17 80000000 80000000 80051F17 80000000 000000BF 80051F1F 00000037 00000037 80000000 80000000 80000000 80000000 80000000 80000000 80000000 80000000 80000000 Rev. 0 | Page 14 of 20 AD1988A/AD1988B Node ID 32 33 34 36 37 38 39 3A 3B 3C 3D Widget Capabilities 09 00300101 00300101 00300101 00300101 00300101 0030010D 0030010D 0030010D 0030010D 0030010D 0030010D PCM Size, Rate 0A Stream Formats 0B Pin Capabilities 0C Input Amp Capabilities 0D Con. List Length 0E 00000002 00000003 00000003 00000003 00000003 00000001 00000001 00000001 00000001 00000001 00000001 Power States 0F Output Amp Capabilities 12 Volume Knob Capabilities 13 Type ID 3 3 3 3 3 3 3 3 3 3 3 00270300 00270300 00270300 00270300 00270300 00270300 Rev. 0 | Page 15 of 20 AD1988A/AD1988B Table 14. Connection List Node ID 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2F 30 31 32 33 34 Connections 0 to 3 4 to 7 0000001D Length 1 0 0 0 0 1 1 1 0 3 7 7 7 1 0 1 1 1 1 1 1 1 0 2 0 1 0 2 2 0 8 1 2 8 1 1 2 2 2 2 2 2 2 1 6 3 2 2 3 3 0 NID 1D I 1 NID I 2 NID I 3 NID I 4 NID I 5 NID I 6 NID I 7 NID 0000001C 0000000C 0000000D 000F0908 2418BC38 2418BC38 2418BC38 0000000E 00000022 00000029 0000002D 0000002B 0000002C 0000002A 00000026 00002120 00000002 00000B01 00002136 3D383339 00000020 00002137 25249811 00000027 00000028 00002132 00002105 0000210A 00002104 00002106 00002130 00002131 0000001E 15141211 00060403 00000A04 00000405 0024253A 0024253C 1A183B34 1C 0C 0D 08 38 38 38 0E 22 29 2D 2B 2C 2A 26 20 02 01 36 39 20 37 11 27 28 32 05 0A 04 06 30 31 1E 11 03 04 05 3A 3C 0B 21 33 21 18 38 3D 34 3B 18 1A 21 09 3C 3C 3C 0F 18 18 18 00203D25 00203D25 00203D25 1 1 1 24 24 24 25 25 25 3D 3D 3D 20 20 20 2120BD38 1 24 25 38 1 3D 20 21 21 21 21 21 21 21 21 12 04 0A 04 25 25 14 06 15 16 17 00001716 24 24 Rev. 0 | Page 16 of 20 AD1988A/AD1988B Node ID 36 37 38 39 3A 3B 3C 3D Connections 0 to 3 4 to 7 00060403 00060403 00000011 00000014 00000015 00000016 00000017 00000012 Length 3 3 1 1 1 1 1 1 0 NID 03 03 11 14 15 16 17 12 I 1 NID 04 04 I 2 NID 06 06 I 3 NID I 4 NID I 5 NID I 6 NID I 7 NID Table 15. Default Configuration Bytes1 MSB LSB Node ID 11 12 13 14 15 16 17 18 1A 1B 1C 24 25 1 31 30 Connectivity Jack Jack Fixed Jack Jack Jack Jack Fixed Fixed Jack Jack Jack Jack Value 02214030 01014010 9913011F 02A19040 01813021 01011012 01A19020 9933012E 99F301F0 014511F0 01C511F0 01016011 01012014 27 24 Location Chassis Position External Front External Rear Internal Special 3 External Front External Rear External Rear External Rear Internal Special 3 Internal Special 3 External Rear External Rear External Rear External Rear 29 28 23 20 Default Device HP out Line out Speaker Mic in Line in Line out Mic in CD Other S/PDIF out S/PDIF in Line out Line out 19 16 Conn Type ⅛” jack ⅛” jack ATAPI ⅛” jack ⅛” jack ⅛” jack ⅛” jack ATAPI ATAPI Optical Optical ⅛” jack ⅛” jack 15 12 Color Green Green Unknown Pink Blue Black Pink Unknown Unknown Black Black Orange Gray 8 8 Misc JD Ovrrd 0 0 1 0 0 0 0 1 1 1 1 0 0 7 4 Def Assn 3 1 1 4 2 1 2 2 F F F 1 1 3 0 Seq 0 0 F 0 1 2 0 E 0 0 0 1 4 Default configuration values are set on codec power-up only. To preserve modifications by BIOS control, default configuration values do not change by reset operations. Rev. 0 | Page 17 of 20 AD1988A/AD1988B JACK PRESENCE DETECTION HD AUDIO STYLE JACK PRESENCE DETECTION The AD1988 uses two jack sense pins for presence detection on up to eight audio jacks. This, combined with the device identification engine, enables software to determine if there is a device plugged into the circuit, and the type of device it is. Allowing software to configure jacks and amplifiers, as necessary, ensures proper audio operation. Detect jack presence by using a resistor tree arrangement detailed by the HD audio specification, allowing up to four jacks per sense line. Jacks must have normally open, isolated switches to use this method of jack presence detection. For proper operation, there must be a 2.67 kΩ 1% resistor connected between SENSE_A and AVDD, and another 2.67 kΩ 1% resistor between SENSE_B and AVDD. The specific resistor values for each jack are listed in Table 16. Use 1% tolerance resistors to ensure accurate detection. Table 16. Jack Sense Mapping Resistor Value (1% Tolerance) 2.67 kΩ 5.10 kΩ 10.0 kΩ 20.0 kΩ 39.2 kΩ Name Pull-up to AVDD FRONT LINE IN FRONT_MIC HP_OUT SENSE_A Port D C B A Node ID 0x12 0x15 0x14 0x11 Name Pull-up to AVDD SURR_SIDE (7.1) C/LFE SURR_BACK (5.1) REAR_MIC SENSE_B Port H G F E Node ID 0x25 0x24 0x16 0x17 Rev. 0 | Page 18 of 20 AD1988A/AD1988B HARDWARE VOLUME CONTROL VDD R1 3.3kΩ GPIO_0/VOLUME R2 10k Ω SW1 UP R3 5.1kΩ SW2 DOWN R4 3.3kΩ OPTIONAL SW3 MUTE 05843-008 To use the GPIO_0/VOLUME pin (Pin 2) as a GPIO pin, it is recommended to pull it down using a 10 kΩ resistor (Pin 2 to DVSS). In the GPIO configuration, the volume control widget has no effect. When the GPIO_0/VOLUME pin (Pin 2) is used as a volume control, pull-up Pin 2 to AVDD. The volume control widget operates the codec volumes only under software control. If one of the buttons is pressed, the control volume setting is incremented (up), decremented (down), or set Bit 7 (mute). The volume control supports 40 steps (other than mute) and uses a range of 0 (0x00, minimum volume) to 63 (0x3F, maximum volume). Pressing the mute switch (or both up and down simultaneously) toggles Bit 7 which indicates mute on/off. Figure 4 . Volume Control Circuitry The AD1988A/AD1988B support external volume control on Pin 2 (GPIO_0/VOLUME). The circuit diagram in Figure 4 allows up/down/mute control using only three switches and four resistors external to the codec. The up/down switches can also be replaced by a center-position-off SPDT toggle switch. The mute switch is optional, but desirable, for a satisfactory user interface. Rev. 0 | Page 19 of 20 AD1988A/AD1988B OUTLINE DIMENSIONS 0.75 0.60 0.45 1.60 MAX 48 1 PIN 1 9.00 BSC SQ 37 36 1.45 1.40 1.35 TOP VIEW 0.20 0.09 7° 3.5° 0° 0.08 MAX COPLANARITY (PINS DOWN) 7.00 BSC SQ 0.15 0.05 12 13 24 25 SEATING PLANE VIEW A 0.50 BSC LEAD PITCH VIEW A ROTATED 90° CCW COMPLIANT TO JEDEC STANDARDS MS-026-BBC 0.27 0.22 0.17 Figure 5. 48-Lead Low Profile Quad Flat Package [LQFP] (ST-48) Dimension shown in millimeters 7.00 BSC SQ 0.60 MAX 0.60 MAX 37 36 0.30 0.23 0.18 48 1 PIN 1 INDICATOR PIN 1 INDICATOR TOP VIEW 6.75 BSC SQ EXPOSED PAD (BOTTOM VIEW) 5.25 5.10 SQ 4.95 0.50 0.40 0.30 25 24 12 13 0.25 MIN 5.50 REF 1.00 0.85 0.80 12° MAX 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM 0.50 BSC SEATING PLANE 0.20 REF COPLANARITY 0.08 COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2 Figure 6. 48-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 7 mm × 7 mm Body, Very Thin Quad (CP-48-1) Dimension shown in millimeters ORDERING GUIDE Model AD1988AJSTZ1 AD1988AJSTZ-RL1 AD1988AJCPZ1 AD1988AJCPZ-RL1 AD1988BJSTZ1 AD1988BJSTZ-RL1 AD1988BJCPZ1 AD1988BJCPZ-RL1 1 Audio Output Performance 95 dB 95 dB 95 dB 95 dB 101 dB 101 dB 101 dB 101 dB Temperature Range 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C Package Description 48-Lead LQFP, Tray 48-Lead LQFP, Reel 48-Lead LFCSP_VQ, Tray 48-Lead LFCSP_VQ, Reel 48-Lead LQFP, Tray 48-Lead LQFP, Reel 48-Lead LFCSP_VQ, Tray 48-Lead LFCSP_VQ, Reel Package Option ST-48 ST-48 CP-48-1 CP-48-1 ST-48 ST-48 CP-48-1 CP-48-1 Z = Pb-free part. Dolby and Dolby Master Studio are trademarks of Dolby Laboratories. DTS is a trademark of DTS, Inc. Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05843-0-10/06(0) Rev. 0 | Page 20 of 20