Voltage Output Temperature Sensor
with Signal Conditioning
AD22100
FUNCTIONAL BLOCK DIAGRAM
V+
200°C temperature span
Accuracy better than ±2% of full scale
Linearity better than ±1% of full scale
Temperature coefficient of 22.5 mV/°C
Output proportional to temperature × V+
Single-supply operation
Reverse voltage protection
Minimal self-heating
High level, low impedance output
VOUT
RT
00673-C-001
FEATURES
Figure 1.
APPLICATIONS
HVAC systems
System temperature compensation
Board level temperature sensing
Electronic thermostats
Industrial process control
Instrumentation
Automotive
REFERENCE
AD22100
VO
SIGNAL OUTPUT
DIRECT TO ADC
INPUT
1k
0.1F
–50C TO +150C
GENERAL DESCRIPTION
The AD22100 is a monolithic temperature sensor with on-chip
signal conditioning. It can be operated over the temperature
range −50°C to +150°C, making it ideal for use in numerous
HVAC, instrumentation, and automotive applications.
ANALOG-TODIGITAL
CONVERTER
00673-C-002
MARKETS
+5V
Figure 2. Application Circuit
The signal conditioning eliminates the need for any trimming,
buffering, or linearization circuitry, greatly simplifying the
system design and reducing the overall system cost.
The output voltage is proportional to the temperature x the
supply voltage (ratiometric). The output swings from 0.25 V at
−50°C to +4.75 V at +150°C using a single +5.0 V supply.
Due to its ratiometric nature, the AD22100 offers a costeffective solution when interfacing to an analog-to-digital
converter. This is accomplished by using the ADC’s +5 V
power supply as a reference to both the ADC and the AD22100
eliminating the need for and cost of a precision reference (see
Figure 2).
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2004 Analog Devices, Inc. All rights reserved.
AD22100
TABLE OF CONTENTS
Specifications..................................................................................... 3
Output Stage Considerations.......................................................7
Chip Specifications....................................................................... 3
Ratiometricity Considerations ....................................................8
Absolute Maximum Ratings............................................................ 4
Mounting Considerations ............................................................8
ESD Caution.................................................................................. 4
Thermal Environment Effects .....................................................8
Pin Configurations and Function Descriptions ........................... 5
Microprocessor A/D Interface Issues .........................................9
Typical Performance Characteristics ............................................. 6
Use with a Precision Reference as the Supply Voltage................9
Theory of Operation ........................................................................ 7
Outline Dimensions ....................................................................... 10
Absolute Accuracy and Nonlinearity Specifications ............... 7
Ordering Guide .......................................................................... 11
REVISION HISTORY
7/04—Data Sheet Changed from Rev. C to Rev. D
Change to AD22100K Specifications............................................. 3
Updated Outline Dimensions ....................................................... 10
Changes to Ordering Guide .......................................................... 11
6/04—Data Sheet Changed from Rev. B to Rev. C
Changes to Format .............................................................Universal
Changes to Specifications ................................................................ 3
Changes to Chip Specifications ...................................................... 3
Changes to Ratiometricity Considerations Section ..................... 8
Changes to Ordering Guide .......................................................... 10
Updated Outline Dimensions ....................................................... 10
12/94—Data Sheet Changed from Rev. A to Rev. B
Rev. D | Page 2 of 12
AD22100
SPECIFICATIONS
TA = 25°C and V+ = 4 V to 6.5 V, unless otherwise noted.
Table 1.
Parameter
TRANSFER FUNCTION
TEMPERATURE COEFFICIENT
TOTAL ERROR
Initial Error
TA = 25°C
Error Overtemperature
TA = TMIN
TA = TMAX
Nonlinearity
TA = TMAX to TMIN
OUTPUT CHARACTERISTICS
Nominal Output Voltage
V+ = 5.0 V, TA = 0°C
V+ = 5.0 V, TA = +100°C
V+ = 5.0 V, TA = −40°C
V+ = 5.0 V, TA = +85°C
V+ = 5.0 V, TA = −50°C
V+ = 5.0 V, TA = +150°C
POWER SUPPLY
Operating Voltage
Quiescent Current
TEMPERATURE RANGE
Guaranteed Temperature Range
Operating Temperature Range
PACKAGE
1
Min
AD22100K
AD22100A
AD22100S
Typ
Max
Min
Typ
Max
Min
Typ
Max
VOUT = (V+/5 V) × [1.375 V +(22.5 mV/°C) × TA]
(V+/5 V) × 22.5
Unit
V
mV/°C
±0.5
±2.0
±1.0
±2.0
±1.0
±2.0
°C
±0.75
±0.75
±2.0
±2.0
±2.0
±2.0
±3.7
±3.0
±3.0
±3.0
±4.0
±4.0
°C
°C
1.0
% FS1
0.5
0.5
1.375
3.625
V
V
V
V
V
V
0.475
3.288
0.250
4.750
4.0
5.0
500
0
−50
6.5
650
4.0
+100
+150
−40
−50
TO-92
SOIC
5.0
500
6.5
650
4.0
+85
+150
−50
−50
TO-92
SOIC
5.0
500
6.5
650
V
µA
+150
+150
°C
°C
TO-92
SOIC
FS (full scale) is defined as the operating temperature range −50°C to +150°C. The listed maximum specification limit applies to the guaranteed temperature range.
For example, the AD22100K has a nonlinearity of (0.5%) × (200°C) = 1°C over the guaranteed temperature range of 0°C to +100°C.
CHIP SPECIFICATIONS
TA = 25°C and V+ = 5.0 V, unless otherwise noted.
Table 2.
Paramater
TRANSFER FUNCTION
TEMPERATURE COEFFICIENT
OUTPUT CHARACTERISTICS
Error
TA = 25°C
Nominal Output Voltage
TA = 25°C
POWER SUPPLY
Operating Voltage
Quiescent Current
TEMPERATURE RANGE
Guaranteed Temperature Range
Operating Temperature Range
Min
Typ
Max
VOUT = (V+/5 V) × [1.375 V +(22.5 mV/°C) × TA]
(V+/5 V) × 22.5
±0.5
±2.0
1.938
4.0
5.0
500
Rev. D | Page 3 of 12
°C
V
6.5
650
V
µA
+150
°C
°C
+25
−50
Unit
V
mV/°C
AD22100
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
Supply Voltage
Reversed Continuous Supply Voltage
Operating Temperature
Storage Temperature
Output Short Circuit to V+ or Ground
Lead Temperature Range
(Soldering 10 sec)
Junction Temperature
Rating
10 V
−10 V
–50°C to +150°C
–65°C to +160°C
Indefinite
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
150°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. D | Page 4 of 12
AD22100
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
VO
V+ 1
VO 2
GND
2
NC
6 NC
TOP VIEW
GND 4 (Not to Scale) 5 NC
3
BOTTOM VIEW
(Not to Scale)
NC
7
NC 3
00673-C-003
1
8
NC = NO CONNECT
00673-C-004
V+
AD22100
Figure 4. 8-Lead SOIC
Figure 3. 3-Lead TO-92
Table 4. 3-Lead TO-92 Pin Function Descriptions
Table 5. 8-Lead SOIC Pin Function Descriptions
Pin No.
1
2
3
Pin No.
1
2
3
4
5
6
7
8
Mnemonic
V+
VO
GND
Description
Power Supply Input.
Device Output.
Ground Pin Must Be Connected to 0 V.
Rev. D | Page 5 of 12
Mnemonic
V+
VO
NC
GND
NC
NC
NC
NC
Description
Power Supply Input.
Device Output.
No Connect.
Ground Pin Must Be Connected to 0 V.
No Connect.
No Connect.
No Connect.
No Connect.
AD22100
TYPICAL PERFORMANCE CHARACTERISTICS
250
16
14
200
(SOIC)
θJA(°C/W)
T (T0-92)
10
8
6
150
T (SOIC)
4
2
0
400
800
FLOW RATE (CFM)
00673-C-006
100
00673-C-005
τ (Sec)
12
(T0-92)
50
0
1200
400
800
FLOW RATE (CFM)
Figure 6. Thermal Resistance vs. Flow Rate
Figure 5. Thermal Response vs. Flow Rate
Rev. D | Page 6 of 12
1200
AD22100
THEORY OF OPERATION
4
The AD22100 is a ratiometric temperature sensor IC whose
output voltage is proportional to its power supply voltage. The
heart of the sensor is a proprietary temperature-dependent
resistor, similar to an RTD, which is built into the IC. Figure 7
shows a functional block diagram of the AD22100.
3
MAXIMUM ERROR
OVER TEMPERATURE
ERROR (°C)
2
V+
1
0
TYPICAL ERROR
–1
–2
–3
–4
–50
00673-C-001
RT
MAXIMUM ERROR
OVER TEMPERATURE
00673-C-007
VOUT
Figure 7. Simplified Block Diagram
0
50
TEMPERATURE (°C)
100
150
Figure 8. Typical AD22100 Performance
The temperature-dependent resistor, labeled RT, exhibits a
change in resistance that is nearly linearly proportional to
temperature. This resistor is excited with a current source that is
proportional to the power supply voltage. The resulting voltage
across RT is therefore both supply voltage proportional and linearly varying with temperature. The remainder of the AD22100
consists of an op amp signal conditioning block that takes the
voltage across RT and applies the proper gain and offset to
achieve the following output voltage function:
OUTPUT STAGE CONSIDERATIONS
As previously stated, the AD22100 is a voltage output device. A
basic understanding of the nature of its output stage is useful for
proper application. Note that at the nominal supply voltage of
5.0 V, the output voltage extends from 0.25 V at –50°C to +4.75
V at +150°C. Furthermore, the AD22100 output pin is capable
of withstanding an indefinite short circuit to either ground or
the power supply. These characteristics are provided by the output stage structure shown in Figure 9.
VOUT = (V+/5 V) × (1.375 V + 22.5 mV/°C × TA)
V+
ABSOLUTE ACCURACY AND NONLINEARITY
SPECIFICATIONS
Figure 8 graphically depicts the guaranteed limits of accuracy
for the AD22100 and shows the performance of a typical part.
As the output is very linear, the major sources of error are offset, for instance error at room temperature, span error, and deviation from the theoretical 22.5 mV/°C. Demanding applications can achieve improved performance by calibrating these
offset and gain errors so that only the residual nonlinearity remains as a significant source of error.
00673-C-008
VOUT
Figure 9. Output Stage Structure
The active portion of the output stage is a PNP transistor,
with its emitter connected to the V+ supply and its collector
connected to the output node. This PNP transistor sources the
required amount of output current. A limited pull-down capability is provided by a fixed current sink of about −80 µA, with
the term fixed referring to a current sink that is fairly insensitive
to either supply voltage or output loading conditions. The current sink capability is a function of temperature, increasing its
pull-down capability at lower temperatures.
Rev. D | Page 7 of 12
AD22100
Due to its limited current sinking ability, the AD22100 is incapable of driving loads to the V+ power supply and is instead
intended to drive grounded loads. A typical value for shortcircuit current limit is 7 mA, so devices can reliably source 1
mA or 2 mA. However, for best output voltage accuracy and
minimal internal self-heating, output current should be kept
below 1 mA. Loads connected to the V+ power supply should
be avoided as the current sinking capability of the AD22100 is
fairly limited. These considerations are typically not a problem
when driving a microcontroller analog-to-digital converter input
pin (see the Microprocessor A/D Interface Issues section).
RATIOMETRICITY CONSIDERATIONS
The AD22100 will operate with slightly better accuracy than
that listed in the data sheet specifications if the power supply is
held constant. This is because the AD22100’s output voltage
varies with both temperature and supply voltage, with some
errors. The ideal transfer function describing output voltage is:
(V+/5 V) × (1.375 V + 22.5 mV/°C × TA)
The ratiometricity error is defined as the percent change away
from the ideal transfer function as the power supply voltage
changes within the operating range of 4 V to 6.5 V. For the
AD22100, this error is typically less than 1%. A movement from
the ideal transfer function by 1% at 25°C, with a supply voltage
varying from 5.0 V to 5.50 V, results in a 1.94 mV change in
output voltage or 0.08°C error. This error term is greater at
higher temperatures because the output (and error term) is
directly proportional to temperature. At 150°C, the error in
output voltage is 4.75 mV or 0.19°C.
For example, with VS = 5.0 V, and TA = +25°C, the nominal
output of the AD22100 will be 1.9375 V. At VS = 5.50 V, the
nominal output will be 2.1313 V, an increase of 193.75 mV. A
proportionality error of 1% is applied to the 193.75 mV, yielding
an error term of 1.9375 mV. This error term translates to a
variation in output voltage of 2.1293 V to 2.3332 V. A 1.94 mV
error at the output is equivalent to about 0.08°C error in
accuracy.
If 150°C is substituted for 25°C in the above example, the error
term translates to a variation in output voltage of 5.2203 V to
5.2298 V. A 4.75 mV error at the output is equivalent to about
0.19°C error in accuracy.
MOUNTING CONSIDERATIONS
If the AD22100 is thermally attached and properly protected, it
can be used in any measuring situation where the maximum
range of temperatures encountered is between −50°C and
+150°C. Because plastic IC packaging technology is employed,
excessive mechanical stress must be avoided when fastening the
device with a clamp or screw-on heat tab. Thermally conductive
epoxy or glue is recommended for typical mounting conditions.
In wet or corrosive environments, an electrically isolated metal
or ceramic well should be used to shield the AD22100. Because
the part has a voltage output (as opposed to current), it offers
modest immunity to leakage errors, such as those caused by
condensation at low temperatures.
THERMAL ENVIRONMENT EFFECTS
The thermal environment in which the AD22100 is used
determines two performance traits: the effect of self-heating on
accuracy and the response time of the sensor to rapid changes
in temperature. In the first case, a rise in the IC junction
temperature above the ambient temperature is a function of two
variables: the power consumption of the AD22100 and the
thermal resistance between the chip and the ambient environment θJA. Self-heating error in °C can be derived by multiplying
the power dissipation by θJA. Because errors of this type can
vary widely for surroundings with different heat-sinking capacities, it is necessary to specify θJA under several conditions. Table
6 shows how the magnitude of self-heating error varies relative
to the environment. A typical part will dissipate about 2.2 mW
at room temperature with a 5 V supply and negligible output
loading. Table 6 indicates a θJA of 190°C/W in still air, without a
heat sink, yielding a temperature rise of 0.4°C. Thermal rise will
be considerably less in either moving air or with direct physical
connection to a solid (or liquid) body.
Table 6. Thermal Resistance (TO-92)
Medium
Aluminum Block
Moving Air2
Without Heat Sink
Still Air
Without Heat Sink
Rev. D | Page 8 of 12
θJA (°C/W)
60
t (sec)1
2
75
3.5
190
15
AD22100
Response of the AD22100 output to abrupt changes in ambient
temperature can be modeled by a single time constant t exponential function. Figure 10 shows the typical response time
plots for a few media of interest.
100
ALUMINUM
BLOCK
MOVING
AIR
90
% OF FINAL VALUES
80
70
60
STILL AIR
50
40
30
00673-C-009
20
10
0
0
10
20
30
40
50
60
TIME (sec)
70
80
90
100
Figure 10. Response Time
The time constant t is dependent on θJA and the thermal capacities of the chip and the package. Table 6 lists the effective t (time
to reach 63.2% of the final value) for a few different media.
Copper printed circuit board connections were neglected in the
analysis; however, they will sink or conduct heat directly
through the AD22100’s solder plated copper leads. When faster
response is required, a thermally conductive grease or glue
between the AD22100 and the surface temperature being
measured should be used.
MICROPROCESSOR A/D INTERFACE ISSUES
The AD22100 is especially well suited to providing a low cost
temperature measurement capability for microprocessor/
microcontroller based systems. Many inexpensive 8-bit microprocessors now offer an onboard 8-bit ADC capability at a
modest cost premium. Total cost of ownership then becomes a
function of the voltage reference and analog signal conditioning
necessary to mate the analog sensor with the microprocessor
ADC. The AD22100 can provide an ideal low cost system by
eliminating the need for a precision voltage reference and any
additional active components. The ratiometric nature of the
AD22100 allows the microprocessor to use the same power
supply as its ADC reference. Variations of hundreds of millivolts in the supply voltage have little effect as both the
AD22100 and the ADC use the supply as their reference. The
nominal AD22100 signal range of 0.25 V to 4.75 V (−50°C to
+150°C) makes good use of the input range of a 0 V to 5 V
ADC. A single resistor and capacitor are recommended to provide immunity to the high speed charge dump glitches seen at
many microprocessor ADC inputs (see Figure 2).
An 8-bit ADC with a reference of 5 V will have a least significant bit (LSB) size of 5 V/256 = 19.5 mV. This corresponds to a
nominal resolution of about 0.87°C.
USE WITH A PRECISION REFERENCE AS THE SUPPLY
VOLTAGE
While the ratiometric nature of the AD22100 allows for system
operation without a precision voltage reference, it can still be
used in such systems. Overall system requirements involving
other sensors or signal inputs may dictate the need for a fixed
precision ADC reference. The AD22100 can be converted to
absolute voltage operation by using a precision reference as the
supply voltage. For example, a 5.00 V reference can be used to
power the AD22100 directly. Supply current will typically be
500 µA, which is usually within the output capability of the
reference. Using a large number of AD22100s may require an
additional op amp buffer, as would scaling down a 10.00 V reference that might be found in instrumentation ADCs typically
operating from ±15 V supplies.
1
The time constant t is defined as the time to reach 63.2% of the final
temperature change.
2
1200 CFM.
Rev. D | Page 9 of 12
AD22100
OUTLINE DIMENSIONS
0.210 (5.33)
0.170 (4.32)
0.165 (4.19)
0.125 (3.18)
0.050 (1.27)
MAX
0.019 (0.482)
SQ
0.016 (0.407)
0.205 (5.21)
0.175 (4.45)
0.055 (1.40)
0.045 (1.15)
3
2
0.105 (2.66)
0.095 (2.42)
0.135 (3.43)
MIN
1
0.115 (2.92)
0.080 (2.03)
0.500 (12.70) MIN
0.115 (2.92)
0.080 (2.03)
SEATING
PLANE
BOTTOM VIEW
COMPLIANT TO JEDEC STANDARDS TO-226AA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 11. 3-Pin Plastic Header Package [TO-92]
(T-3)
Dimensions shown in inches and millimeters
5.00 (0.1968)
4.80 (0.1890)
8
5
4.00 (0.1574)
3.80 (0.1497) 1
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
6.20 (0.2440)
5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
COPLANARITY
SEATING 0.31 (0.0122)
0.10
PLANE
0.50 (0.0196)
× 45°
0.25 (0.0099)
8°
0.25 (0.0098) 0° 1.27 (0.0500)
0.40 (0.0157)
0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-012AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 12. 8-Lead Standard Small Outline Package [SOIC]
(R-8)
Dimensions shown in inches and millimeters
Rev. D | Page 10 of 12
AD22100
ORDERING GUIDE
Models
AD22100KT
AD22100KR
AD22100KR-REEL7
AD22100KRZ1
AD22100KRZ-REEL71
AD22100AT
AD22100AR
AD22100AR-REEL
AD22100AR-REEL7
AD22100ST
AD22100SR
AD22100SR-REEL7
AD22100SRZ1
AD22100SRZ-REEL71
AD22100KCHIPS
1
Temperature Range
0°C to +100°C
0°C to +100°C
0°C to +100°C
0°C to +100°C
0°C to +100°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–50°C to +150°C
–50°C to +150°C
–50°C to +150°C
–50°C to +150°C
–50°C to +150°C
Package Description
3-Pin Plastic Header Package (TO-92)
8-Lead Standard Small Outline Package (SOIC)
8-Lead Standard Small Outline Package (SOIC)
8-Lead Standard Small Outline Package (SOIC)
8-Lead Standard Small Outline Package (SOIC)
3-Pin Plastic Header Package (TO-92)
8-Lead Standard Small Outline Package (SOIC)
8-Lead Standard Small Outline Package (SOIC)
8-Lead Standard Small Outline Package (SOIC)
3-Pin Plastic Header Package (TO-92)
8-Lead Standard Small Outline Package (SOIC)
8-Lead Standard Small Outline Package (SOIC)
8-Lead Standard Small Outline Package (SOIC)
8-Lead Standard Small Outline Package (SOIC)
DIE
Z = Pb-free part.
Rev. D | Page 11 of 12
Package Outline
T-3
R-8
R-8
R-8
R-8
T-3
R-8
R-8
R-8
T-3
R-8
R-8
R-8
R-8
AD22100
NOTES
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
C00673–0–7/04(D)
Rev. D | Page 12 of 12
工商网监
湘ICP备2023018690号
