AD394TD/883B

µP-Compatible Multiplying Quad 12-Bit D/A Converter AD394 FEATURES Four, complete, 12-bit CMOS DACs with buffer registers Linearity error: ±1/2 LSB TMIN, TMAX (AD394T) Factory-trimmed gain and offset Precision output amplifiers for VOUT Full four-quadrant multiplication per DAC Monoticity guaranteed over full temperature range Fast settling: 15 µs maximum to ±1/2 LSB Available in MIL-STD-883B OBS PRODUCT DESCRIPTION OLE The AD394 contains four 12-bit, high-speed, low power, voltage output, multiplying digital-to-analog converters in a compact 28-pin hybrid package. The design is based on a proprietary, latched, 12-bit, CMOS DAC chip, which reduces chip count and provides high reliability. The AD394 is ideal for systems requiring digital control of many analog voltages where board space is at a premium and low power consumption is a necessity. Such applications include automatic test equipment, process controllers, and vector stroke displays. The AD394 is laser-trimmed to ±1/2 LSB maximum differential and integral linearity (AD394T) and full-scale accuracy of ±0.05 percent at 25°C. The high initial accuracy is possible because of the use of precision, laser-trimmed, thin-film scaling resistors. TE Figure 1. Functional Block Diagram PRODUCT HIGHLIGHTS 1. The AD394 offers a dramatic reduction in printed circuit board space in systems using multiple low power DACs. 2. Each DAC is independently addressable and provides versatile control architecture for a simple interface to microprocessors. All latch enable signals are leveltriggered. The AD394 outputs (VREFIN = 10 V) provide a ±10 V bipolar output range with positive-true offset binary input coding. 3. The output voltage is trimmed to a full-scale accuracy of ±0.05%. Settling time to ±1/2 LSB is 15 µs maximum. The AD394 is packaged in a 28-lead ceramic package and is available for operation over a −55°C to +125°C temperature range. 4. A maximum gain TC of 5 ppm/°C is achievable. 5. Two- or four-quadrant multiplication can be achieved simply by applying the appropriate input voltage signal to the selected DAC's reference (VREFIN). 6. The AD394TD features guaranteed accuracy and linearity over the −55°C to +125°C temperature range. The individual DAC registers are accessed by the CS1 through CS4 control pins. These control signals allow any combination of the DAC select matrix to occur (see Table 3). Once selected, the DAC is loaded with a single 12-bit wide word. The 12-bit parallel digital input interfaces to most 12- and 16-bit bus systems. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 © 2004 Analog Devices, Inc. All rights reserved. AD394 TABLE OF CONTENTS Specifications..................................................................................... 3 Analog Circuit Details ..................................................................8 Absolute Maximum Ratings............................................................ 5 Operation From ±12 V Supplies..................................................9 ESD Caution.................................................................................. 5 Power Supply Decoupling ............................................................9 Pin Configuration and Functional Block Diagram...................... 6 Improving Full-Scale Stability .....................................................9 Theory of Operation ........................................................................ 7 Applications ...................................................................................9 Multiplying Mode......................................................................... 7 Applications ................................................................................ 10 OBS Data and Control Signal Format ................................................ 7 Package Outline .............................................................................. 12 Timing............................................................................................ 8 Ordering Guide .......................................................................... 12 REVISION HISTORY 9/04–Rev. 0 Changed to Rev. A OLE Updated format....................................................................... Universal Deleted AD395 part................................................................ Universal Change to Product Description...........................................................1 Changes to Specifications table............................................................3 Delete Figure 3 .......................................................................................4 Delete Figure 6 .......................................................................................5 Change to Theory of Operation section.............................................7 7/85–Initial Version: Revision 0 Rev. A | Page 2 of 12 TE AD394 SPECIFICATIONS Table 1. TA = 25°C, VREFIN = 10 V, VS = ±15 V, unless otherwise specified Model DATA INPUTS (Pins 1-16)2 TTL or 5 V CMOS-Compatible Input Voltage Bit ON (Logic 1) Bit OFF (Logic 0) Input Current RESOLUTION OUTPUT Voltage Range3 Current STATIC ACCURACY Gain Error Offset Bipolar Zero Integral Linearity Error5 Differential Linearity Error TEMPERATURE PERFORMANCE Gain Drift Offset Drift Integrated Linearity Error5 TMIN to TMAX Differential Linearity Error Min AD394TD and AD394TD/883B1 Typ 2.4 0 ±4 OBS Max Units 5.5 0.8 ±40 12 V V µA Bits ±VREFIN V mA 5 ±0.025 ±0.012 ±0.012 ±1/8 ±1/4 OLE REFERENCE INPUTS Input Resistance Voltage Range DYNAMIC PERFORMACE Setting Time (to ±1/2 LSB) VPREFIN = 10 V, Change All Digital Inputs from 5.0 V to 0 V VREFIN = 0 V to 5 V Step, All Digital Inputs = 0 V Reference Feedthrough Error Digital-to-Analog Glitch Impulse6 Crosstalk Digital Input (Static)7 Reference8 POWER REQUIREMENTS Supply Voltage9 Current (All Digital Inputs 0 V or 5 V) +VS −VS Power Dissipation ±1/2 ±1/2 % of FSR4 % of FSR % of FSR LSB LSB ±5 ±5 ppm FSR/°C ppm FSR/°C ±0.05 ±0.025 TE ±1/4 ±1/2 MONOTONICITY GUARANTEED OVER FULL TEMPERATURE RANGE 5 −11 25 +11 kΩ V 10 15 µs 10 See Figure 2 250 15 µs nV-s 0.1 2.0 ±13.5 40 18 570 Rev. A | Page 3 of 12 LSB LSB mV p-p ±16.5 V 48 28 750 mA mA mW AD394 Model POWER SUPPLY GAIN SENSITIVITY +VS −VS TEMPERATURE RANGE Operating (Full Specifications) T Storage Min AD394TD and AD394TD/883B1 Typ Max 0.002 0.0025 Units −55 −65 %FS/% %FS/% 125 150 °C °C 1 The AD394 T grade is available to MIL-STD-883, Method 5008, Class B. See Analog Devices Military Catalog (1985) for proper part number and detail specification. Timing specifications appear in Table 5 and Figure 6. 3 See the Theory of Operation section for code tables and graphs. 4 FSR means full-scale range and is equal to 20 V for a ±10 V bipolar range and 10 V for a 0 V to 10 V unipolar range. 5 Integral nonlinearity is a measure of the maximum deviation from a straight line passing through the endpoints of the DAC transfer function. 6 This is a measure of the amount of charge injected from the digital inputs to the analog outputs when the inputs change state. It is usually specified as the area of the glitch in nVs and is measured with VREFIN = AGND. 7 Digital crosstalk is defined as the change in any one output’s steady state value as a result of any other output being driven from VOUTMIN to VOUTMAX into a 2kΩ load by means of varying the digital input code. 8 Reference crosstalk is defined as the change in any one output as a result of any other output being driven from VOUTMIN to VOUTMAX @10 kHz into a 2 kΩ load by means of varying the amplitude of the reference signal. 9 The AD394 can be used with supply voltages as low as ±11.4 V. See Figure 10. OBS 2 OLE TE Rev. A | Page 4 of 12 AD394 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter +VS to DGND −VS to DGND Digital Inputs (Pins 1-16) to DNGD VREFIN to DGND AGND to DGND Analog Output (Pins 18, 21, 24, 27) Rating −0.3 V to +17 V −17 V to +0.3 V −0.3 V to +7 V ±25 V ±0.6 V Indefinite short to AGND or DGND momentary short to ±VS Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation at or above this specification is not implied. Exposure to above maximum rating conditions for extended periods may affect device reliability. OBS ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. OLE MIL-STD-883 TE The rigors of the military and aerospace environment, temperature extremes, humidity, mechanical stress, etc., demand the utmost in electronic circuits. The AD394, with the inherent reliability of an integrated circuit construction, was designed with these applications in mind. The hermetically-sealed, low profile DIP package takes up a fraction of the space required by equivalent modular designs and protects the chips from hazardous environments. To further insure reliability, the AD394 is fully compliant to MIL-STD-833 Class B, Method 5008. Figure 2. Feedthrough VREFIN = 60 Hz (Top Photo) and 400 Hz (Bottom Photo). The Sine-Wave Digital Code Is Set at 1000 000 0000. Scale: Reference Input Is 5 V/DIV (Thin Trace). Feedthrough Output Is 5 mV/DIV. Time: 5 ms/DIV (Top Photo), 500 µs/DIV (Bottom Photo). Rev. A | Page 5 of 12 AD394 PIN CONFIGURATION AND FUNCTIONAL BLOCK DIAGRAM OBS OLE Figure 3. Pin Configuration Figure 4. Functional Block Diagram (Bipolar) Rev. A | Page 6 of 12 TE AD394 THEORY OF OPERATION The AD394 quad DAC provides four-quadrant multiplication. It is a hybrid IC comprised of four, monolithic, 12-bit, CMOS, multiplying DACs and eight precision output amplifiers. Each of the four independent-buffered channels has an independent reference input capable of accepting a separate dc or ac signal for multiplying or for function generation applications. The CMOS DACs act as digitally programmable attenuators when used with a varying input signal or, if used with a fixed dc reference, the DAC would act as a standard bipolar output DAC. In addition, each DAC has a 12-bit wide data latch to buffer the converter when connected to a microprocessor data bus. OBS Figure 5. The AD394 as a Four-Quadrant Multiplier of Reference and Digital Input MULTIPLYING MODE Figure 5 shows the transfer function. The diagram indicates an area over which many different combinations of the reference input and digital input can result in a particular analog output voltage. The highlighted transfer line in the diagram indicates the transfer function if a fixed reference is at the input. The digital code above the diagram indicates the midpoint and endpoints of each function. The relationship between the reference input (VREFIN), the digital input code, and the analog output is given in Table 4. Note that the reference input signal sets the slope of the transfer function (and determines the fullscale output at code 111...111), while the digital input selects the horizontal position in each diagram. DATA AND CONTROL SIGNAL FORMAT OLE The AD394 accepts 12-bit parallel data in response to Control Signals CS1–CS4. As detailed in Table 3, the four chip select lines are used to address the DAC register of interest. It is permissible to have more than one chip select active at any time. If CS1–CS4 are all brought low coincident, all four DAC outputs will be updated to the value located on the data bus. All control inputs are level-triggered and may be hard-wired low to render any register (or group of registers) transparent. TE Table 3. DAC Select Matrix CS1 CS2 CS3 CS4 1 0 1 1 1 0 1 1 0 1 1 0 1 1 1 0 1 0 1 1 1 1 0 0 Operation All DACs latched Load DAC 1 from data bus Load DAC 2 from data bus Load DAC 3 from data bus Load DAC 4 from data bus All DACs simultaneously loaded Table 4. Bipolar Code Table Data Input 1111 1111 1111 Analog Output 1 × (VREFIN) 1100 0000 0000 1 × (VREFIN) ⎧ 1024 ⎫ ⎨ ⎬ ⎩ 2048 ⎭ 5.000 V 1/2 Scale 1000 0000 0001 1 × (VREFIN) ⎧ 1 ⎫ ⎨ ⎬ ⎩ 2048 ⎭ 4.88 mV 1 LSB 1000 0000 0000 1 × (VREFIN) ⎧ 0 ⎫ ⎨ ⎬ ⎩ 2048 ⎭ 0.000 V Zero 0111 1111 1111 −1 × (VREFIN) ⎧ 1 ⎫ ⎨ ⎬ ⎩ 2048 ⎭ −4.88 mV −1LSB 0100 0000 0000 −1 × (VREFIN) ⎧ 1024 ⎫ ⎨ ⎬ ⎩ 2048 ⎭ −5.000 V −1/2 Scale 0000 0000 0000 −1 × (VREFIN) ⎧ 2048 ⎫ ⎨ ⎬ ⎩ 2048 ⎭ −10.000 V −Full Scale ⎧ 2047 ⎫ ⎨ ⎬ ⎩ 2048 ⎭ Rev. A | Page 7 of 12 Analog Output Voltage, VREFIN = 10 V 9.9951 V Full Scale − 1 LSB AD394 TIMING The AD394 control signal timing is very straightforward. CS1– CS4 must maintain a minimum pulse width of at least 400 ns for a desired operation to occur. When loading data from a bus into a 12-bit wide data latch, the data must be stable for at least 210 ns before returning CS to a high state. When CS is low, the data latch is transparent, allowing the data at the input to propagate through to the DAC. Data can change immediately after the chip select returns high. DAC settling time is measured from the falling edge of the active chip select. the DAC outputs are accurately developed between the output pin and Pin 23 (AGND), delivering these signals to remote loads can be a problem. These problems are compounded if a current booster stage is used, or if multiple packages are used. Figure 8 illustrates the parasitic impedances that influence output accuracy. Table 5. AD394 Timing Specifications, TMIN to TMAX OBS Symbol tCS tDA tDS tDH Parameter Chip Select Pulse Width Data Access Time Data Setup Time Data Hold Time Typ 170 0 150 5 Units ns min ns min ns min ns min OLE Figure 7. Recommended Ground Connections TE Figure 6. Timing Diagram ANALOG CIRCUIT DETAILS Grounding Rules Figure 8. Grounding Errors in Multiple AD394 Systems The AD394 includes two ground connections to minimize system accuracy degradation arising from grounding errors. The two ground pins are designated DGND (Pin 17) and AGND (Pin 23). The DGND pin is the return for the supply current and serves as the reference point for the digital input thresholds. Thus, DGND should be connected to the same ground as the circuitry that drives the digital inputs. An output buffer configured as a subtracter, as shown in Figure 9, can greatly reduce these errors. First, sensing the voltage directly at the load with R4 eliminates the effects of voltage drops in wiring resistance. Second, sensing the remote ground directly with R3 eliminates the voltage drops caused by currents flowing through ZGA. Resistors R1 through R4 should be well matched to achieve maximum rejection of the voltage appearing across ZGA. Resistors matched to within 1 percent (including the effects of RW2 and RW3) reduce ground interaction errors by a factor of 100. Pin 23, AGND, is a high quality analog ground connection. This pin should serve as the reference point for all analog circuitry associated with the AD394. It is recommended that any analog signal path carrying significant currents have its own return connection to Pin 23, as shown in Figure 7. Several complications arise in practical systems, particularly if the load is referred to a remote ground. These complications include dc gain errors due to wiring resistance between DAC and load, noise due to currents from other circuits flowing in power ground return impedances, and offsets due to multiple load currents sharing the same signal ground returns. While Rev. A | Page 8 of 12 AD394 The AD2710 is a suitable reference source for such systems. It features a guaranteed maximum temperature coefficient of ±1 ppm/°C. The combination of the AD2710LN and AD394, as shown in Figure 11, yields a multiple DAC system with maximum full-scale drift of ±6 ppm/°C and excellent tracking. Figure 9. Use of Subtracter Amplifier to Preserve Accuracy OPERATION FROM ±12 V SUPPLIES OBS The AD394 may be used with ±12 V ±5% power supplies if certain conditions are met. The most important limitation is the output swing available from the output op amps. These amplifiers are capable of swinging only up to 3 V from either supply. Thus, the normal ±10 V output range cannot be used. Changing the output scale is accomplished by changing the reference voltage. With a supply of ±11.4 V (5% less than ±12 V), the output range is restricted to a maximum ±8.4 V swing. It may be useful to scale the output at ±8.192 V (yielding a scale factor of 4 mV per LSB). Figure 11. Low Drift Configuration APPLICATIONS Interfacing the AD394 to Microprocessors The AD394 control logic provides a simple interface to microprocessors. The individual latches allow for multi-DAC interfacing to a single data bus. OLE Figure 10 shows a suggested circuit to set up a ±8.192 V output range. To help prevent poor gain drift due to a possible mismatch between RIN and RTHEVENIN of the divider network, it is recommended to buffer RIN, the potentiometer wiper voltage, with an OP-07. 16-Bit Processors The AD394 is a 12-bit resolution DAC system and is easily interfaced to 16-bit wide data buses. Several possible addressing configurations exist. TE In the circuit shown in Figure 12, a system write signal is used to control the decoded address lines and a 74LS139 decoder driven from the least significant address bits provides the active-low CS1 through CS4 signals. In the circuit in Figure 12, address lines A0 and A1 each select a single DAC of the four contained in the AD394. The use of a separate address line for each DAC allows several DACs to be accessed simultaneously. The address lines are gated by the simultaneous occurrence of a system WR and the appropriately decoded base address. In the addressing scheme shown in Figure 12, A0 represents the least significant word address bit. Data may reside in either the 12 MSBs (left-justified) or the 12 LSBs (right-justified). Left justification is useful when the data-word represents a binary fraction of full scale, while right-justified data usually represents an integer value between 0 and 4095. Figure 10. Connections for ±8.192 V Full Scale (Recommended for ±12 V Power Supplies) POWER SUPPLY DECOUPLING The power supplies used with the AD394 should be well-filtered and regulated. Local supply decoupling consisting of a 10 µF tantalum capacitor in parallel with 0.1 µF ceramic capacitor is suggested. The decoupling capacitors should be connected between the supply pins and the AGND pin. If an output booster is used, its supplies should also be decoupled to the load ground. IMPROVING FULL-SCALE STABILITY In large systems using multiple DACs, it may be desirable for all devices to share a common reference. A precision reference can greatly improve system accuracy and temperature stability. Rev. A | Page 9 of 12 Figure 12. 16-Bit Bus Interface AD394 8-Bit Processors The circuit of Figure 13 shows the general principles for connecting the AD394 to an 8-bit data bus. The 74LS244 buffers the data bus; its outputs are enabled when the DAC address appears on the address bus. The first byte sent to the DAC is loaded to the 74LS373 octal latch and, when the second byte is sent to the DAC, it is combined with the first byte to create a 12-bit word. The connections shown are for right-hand justified data. CS and WR inputs to the DAC are also gated, and when active, the DAC is loaded. Pull-up resistors at the output of the 74LS244 buffer ensure that the inputs to the DAC do not float at an ill-defined level when the DAC is not being addressed. This method of connecting 12-bit DACs to an 8-bit data bus is most cost effective when multiple DACs are utilized for 8-bit data bus applications. OBS the ADC function since the processor can perform the required digital operations under software control. A suitable circuit is shown in Figure 14. The AD311 comparator compares the unknown input voltage to one of the AD394 outputs for the analog-to-digital conversion, while the other three outputs are used as normal DACs. The diode clamp shown limits the voltage swing at the comparator input and improves conversion speed. With careful layout, a new compar-ison can be performed in less than 15 µs, resulting in a 12-bit successive approximation conversion in under 180 µs. The benefit of using the AD394 in this application is that one ADC and three DACs can be implemented with only two IC packages (the AD394 and the comparator). OLE TE Figure 14. Using One AD394 Output for A/D Conversion Programmable Window Comparator The AD394 can be used to perform limit testing of responses to digitally controlled input signals. For example, two DACs may be used to generate software-controlled test conditions for a component or circuit. The response to these input conditions can be either completely converted from analog to digital or simply tested against high and low limits generated by the two DACs in the AD394. Figure 13. 8-Bit Data Bus Interface APPLICATIONS The functional density of the AD394 permits complex analog functions to be produced under digital control, where board space requirements would otherwise be prohibitive. Multipleoutput plotters, multichannel displays, complex waveform generation, and multiple programmable voltage sources can all be implemented with the AD394 in a fraction of the space that would be needed if separate DACs were used. Using the AD394 for Analog-to-Digital Conversion Many systems require both analog output and analog input capability. While complete integrated circuit analog-to-digital converters (such as the AD574A) are readily available, the AD394 can be used as the precision analog section of an ADC if some external logic is available. Several types of analog-todigital converters can be built with a DAC, comparator, and control logic, including staircase, tracking, and successiveapproximation types. In systems that include a micropro-cessor, only a comparator must be added to the AD394 to accomplish Figure 15. Programmable Window Comparator Used in Power-Supply Testing In the circuit shown in Figure 15, two AD311 voltage comparators are used within the AD394 to test the output of a 5 V power-supply regulator. The AD394 VOUT1 output (through an appropriate current booster) drives the input to the regulator to simulate variations in input voltage. The output of the regulator is applied to Comparators 1 and 2, with their outputs wire- Rev. A | Page 10 of 12 AD394 OR’ed with LED indicators as shown. The test limits for each comparator are programmed by the AD394 VOUT2 and VOUT3 outputs. When the output of the device under testing is within the limits, both comparators are off and D1 lights. If the output is above or below the limits, either D4 or D5 lights. code is applied to the DAC; the output voltage is the product of the two—an attenuated version of the input. The maximum attenuation range obtainable utilizing 12 bits is 4096:1 or 72 dB. AD394 as a Multiplier and Attenuator So far, it has been assumed that the reference voltage VREFIN is fixed. In fact, VREFIN can be any voltage within the range of −11 V < VREFIN < +11 V. It can be negative, positive, sinusoidal, or whatever the user prefers. This leads to the name “multiplying D/A converters” because the output voltage, VOUT, is proportional to the product of the digital input word and the voltage at the VREFIN terminal. D VOUT = − 1 (VREFIN ) 0 < D < 4095 ( 4096 ) OBS ( Figure 16. AD394 as a Multiplier or Attenuator ) D is the fractional binary value of the digital word applied to the converter. The AD394 multiplies the digital input value by the analog input voltage at VREFIN for any value of VREFIN up to 22 V p-p. This in itself is a powerful tool. Applications requiring precision multiplication with minimal zero offset and very low distortion should consider the AD394 as a candidate. One popular use for the AD394 is as an audio frequency attenuator. The audio signal is applied to the VREFIN input and the attenuation OLE Rev. A | Page 11 of 12 TE AD394 PACKAGE OUTLINE 1.575 (40.01) MAX 15 28 0.810 (20.57) 0.770 (19.56) 14 1 PIN 1 SEE NOTE 1 0.035 (0.89) 0.015 (0.38) SEE NOTE 3 OBS 0.225 (5.72) MAX 0.180 (4.57) MIN 0.145 (3.68) MIN 0.023 (0.58) 0.014 (0.36) 0.070 (1.78) 0.100 (2.54) BSC 0.030 (0.76) SEE NOTE 4, 7 SEE NOTE 2 0.137 (3.48) MAX SEE NOTE 5 0.620 (15.75) 0.550 (13.97) SEE NOTE 6 0.015 (0.38) 0.008 (0.20) OLE NOTES 1. INDEX AREA; A NOTCH OR A LEAD ONE IDENTIFICATION MARK IS LOCATED ADJACENT TO LEAD ONE. 2. THE MINIMUM LIMIT FOR DIMENSION MAY BE 0.023" (0.58 mm) FOR ALL FOUR CORNER LEADS ONLY. 3. DIMENSION SHALL BE MEASURED FROM THE SEATING PLANE TO THE BASE PLANE. 4. THE BASIC PIN SPACING IS 0.100" (2.54 mm) BETWEEN CENTERLINES. 5. APPLIES TO ALL FOUR CORNERS. 6. MEASURED AT THE CENTERLINE OF THE LEADS. 7. TWENTY SIX SPACES. 8. CONTROLLING DIMENSIONS ARE IN INCHES. MILLIMETER DIMENSIONS ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN Figure 17. 28-Lead Bottom-Brazed Ceramic DIP for Hybrid [BBDIP/H] (DH-28A) Dimensions Shown in Inches and (Millimeters) Note: Squared Corner and Dot in Shaded Area Indicate Pin 1. TE ORDERING GUIDE Model AD394TD AD394TD/883B Temperature Range −55°C to +125°C −55°C to +125°C Gain Error ±2 LSB ±2 LSB © 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C04851-0-9/04(A) Rev. A | Page 12 of 12 Linearity Error (TMIN–TMAX) ±1/2 LSB ±1/2 LSB