Dual Channel, 128-/256-Position, I2C,
Nonvolatile Digital Potentiometer
AD5122A/AD5142A
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
10 kΩ and 100 kΩ resistance options
Resistor tolerance: 8% maximum
Wiper current: ±6 mA
Low temperature coefficient: 35 ppm/°C
Wide bandwidth: 3 MHz
Fast start-up time < 75 µs
Linear gain setting mode
Single- and dual-supply operation
Independent logic supply: 1.8 V to 5.5 V
Wide operating temperature: −40°C to +125°C
3 mm × 3 mm package option
Qualified for automotive applications
VLOGIC
VDD
INDEP
POWER-ON
RESET
AD5122A/
AD5142A
RDAC1
INPUT
REGISTER 1
RESET
SCL
SDA
B1
SERIAL
INTERFACE
RDAC2
7/8
INPUT
REGISTER 2
ADDR1
A2
W2
B2
EEPROM
MEMORY
GND
10939-001
ADDR0
APPLICATIONS
A1
W1
VSS
Portable electronics level adjustment
LCD panel brightness and contrast controls
Programmable filters, delays, and time constants
Programmable power supplies
Figure 1.
GENERAL DESCRIPTION
The AD5122A/AD5142A potentiometers provide a nonvolatile
solution for 128-/256-position adjustment applications, offering
guaranteed low resistor tolerance errors of ±8% and up to ±6 mA
current density in the Ax, Bx, and Wx pins.
The low resistor tolerance and low nominal temperature coefficient
simplify open-loop applications as well as applications requiring
tolerance matching.
The linear gain setting mode allows independent programming
of the resistance between the digital potentiometer terminals,
through RAW and RWB the string resistors, allowing very accurate
resistor matching.
The high bandwidth and low total harmonic distortion (THD)
ensure optimal performance for ac signals, making it suitable
for filter design.
The low wiper resistance of only 40 Ω at the ends of the resistor
array allows for pin-to-pin connection.
Table 1. Family Models
Model
AD51231
AD5124
AD5124
AD51431
AD5144
AD5144
AD5144A
AD5122
AD5122A
AD5142
AD5142A
AD5121
AD5141
1
Channel
Quad
Quad
Quad
Quad
Quad
Quad
Quad
Dual
Dual
Dual
Dual
Single
Single
Position
128
128
128
256
256
256
256
128
128
256
256
128
256
Interface
I2 C
SPI/I2C
SPI
I2 C
SPI/I2C
SPI
I2 C
SPI
I2 C
SPI
I2 C
SPI/I2C
SPI/I2C
Package
LFCSP
LFCSP
TSSOP
LFCSP
LFCSP
TSSOP
TSSOP
LFCSP/TSSOP
LFCSP/TSSOP
LFCSP/TSSOP
LFCSP/TSSOP
LFCSP
LFCSP
Two potentiometers and two rheostats.
The wiper values can be set through an I2C-compatible digital
interface that is also used to read back the wiper register and
EEPROM contents.
The AD5122A/AD5142A are available in a compact, 16-lead,
3 mm × 3 mm LFCSP and a 16-lead TSSOP. The parts are
guaranteed to operate over the extended industrial temperature
range of −40°C to +125°C.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2012–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD5122A/AD5142A
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
RDAC Register and EEPROM .................................................. 20
Applications ....................................................................................... 1
Input Shift Register .................................................................... 20
Functional Block Diagram .............................................................. 1
I2C Serial Data Interface ............................................................ 20
General Description ......................................................................... 1
I2C Address.................................................................................. 20
Revision History ............................................................................... 2
Advanced Control Modes ......................................................... 22
Specifications..................................................................................... 3
EEPROM or RDAC Register Protection ................................. 23
Electrical Characteristics—AD5122A ....................................... 3
INDEP Pin................................................................................... 23
Electrical Characteristics—AD5142A ....................................... 6
RDAC Architecture .................................................................... 26
Interface Timing Specifications .................................................. 9
Programming the Variable Resistor ......................................... 26
Shift Register and Timing Diagrams ....................................... 10
Programming the Potentiometer Divider ............................... 27
Absolute Maximum Ratings .......................................................... 11
Terminal Voltage Operating Range ......................................... 27
Thermal Resistance .................................................................... 11
Power-Up Sequence ................................................................... 27
ESD Caution ................................................................................ 11
Layout and Power Supply Biasing ............................................ 27
Pin Configurations and Function Descriptions ......................... 12
Outline Dimensions ....................................................................... 28
Typical Performance Characteristics ........................................... 14
Ordering Guide .......................................................................... 29
Test Circuits ..................................................................................... 19
Automotive Products ................................................................. 29
Theory of Operation ...................................................................... 20
REVISION HISTORY
6/2017—Rev. A to Rev. B
Changes to Features Section............................................................ 1
Changes to Logic Supply Current Parameter, Table 2 ................. 4
Added Note 12 to Data Retention Parameter, Table 2;
Renumbered Sequentially................................................................ 5
Changes to Logic Supply Current Parameter, Table 3 ................. 7
Added Note 12 to Data Retention Parameter, Table 3;
Renumbered Sequentially................................................................ 8
Changes to Table 5 .......................................................................... 11
Changes to Figure 4 and Table 7 ................................................... 12
Changes to Figure 14 ...................................................................... 15
Added Figure 15; Renumbered Sequentially .............................. 15
Changes to Figure 18...................................................................... 16
Change to Linear Gain Setting Mode .......................................... 22
Changes to EEPROM or RDAC Register Protection Section... 23
Changes to RDAC Architecture Section ..................................... 26
Updated Outline Dimensions ....................................................... 28
Changes to Ordering Guide .......................................................... 29
Added Automotive Products Section .......................................... 29
12/2012—Rev. 0 to Rev. A
Changes to Table 9.......................................................................... 20
10/2012—Revision 0: Initial Version
Rev. B | Page 2 of 32
Data Sheet
AD5122A/AD5142A
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS—AD5122A
VDD = 2.3 V to 5.5 V, VSS = 0 V; VDD = 2.25 V to 2.75 V, VSS = −2.25 V to −2.75 V; VLOGIC = 1.8 V to 5.5 V, −40°C < TA < +125°C, unless
otherwise noted.
Table 2.
Parameter
DC CHARACTERISTICS—RHEOSTAT
MODE (ALL RDACs)
Resolution
Resistor Integral Nonlinearity2
Resistor Differential Nonlinearity2
Nominal Resistor Tolerance
Resistance Temperature Coefficient3
Wiper Resistance3
Bottom Scale or Top Scale
Nominal Resistance Match
DC CHARACTERISTICS—POTENTIOMETER
DIVIDER MODE (ALL RDACs)
Integral Nonlinearity4
Differential Nonlinearity4
Full-Scale Error
Zero-Scale Error
Voltage Divider Temperature
Coefficient3
Symbol
Test Conditions/Comments
N
R-INL
Min
Typ1
Max
7
RAB = 10 kΩ
VDD ≥ 2.7 V
VDD < 2.7 V
RAB = 100 kΩ
VDD ≥ 2.7 V
VDD < 2.7 V
R-DNL
ΔRAB/RAB
(ΔRAB/RAB)/ΔT × 106
RW
Unit
Bits
−1
−2.5
±0.1
±1
+1
+2.5
LSB
LSB
−0.5
−1
−0.5
−8
+0.5
+1
+0.5
+8
Code = full scale
Code = zero scale
RAB = 10 kΩ
RAB = 100 kΩ
±0.1
±0.25
±0.1
±1
35
LSB
LSB
LSB
%
ppm/°C
55
130
125
400
Ω
Ω
RAB = 10 kΩ
RAB = 100 kΩ
Code = 0xFF
−1
40
60
±0.2
80
230
+1
Ω
Ω
%
RAB = 10 kΩ
RAB = 100 kΩ
−0.5
−0.25
−0.25
±0.1
±0.1
±0.1
+0.5
+0.25
+0.25
LSB
LSB
LSB
RAB = 10 kΩ
RAB = 100 kΩ
−1.5
−0.5
−0.1
±0.1
+0.5
LSB
LSB
RBS or RTS
RAB1/RAB2
INL
DNL
VWFSE
VWZSE
(ΔVW/VW)/ΔT × 106
RAB = 10 kΩ
RAB = 100 kΩ
Code = half scale
Rev. B | Page 3 of 32
1
0.25
±5
1.5
0.5
LSB
LSB
ppm/°C
AD5122A/AD5142A
Parameter
RESISTOR TERMINALS
Maximum Continuous Current
Terminal Voltage Range5
Capacitance A, Capacitance B3
Capacitance W3
Common-Mode Leakage Current3
DIGITAL INPUTS
Input Logic3
High
Low
Input Hysteresis3
Input Current3
Input Capacitance3
DIGITAL OUTPUTS
Output High Voltage3
Output Low Voltage3
Data Sheet
Symbol
Negative Supply Current
EEPROM Store Current3, 6
EEPROM Read Current3, 7
Logic Supply Current
Power Dissipation8
Power Supply Rejection Ratio
Min
RAB = 10 kΩ
RAB = 100 kΩ
−6
−1.5
VSS
Typ1
Max
Unit
+6
+1.5
VDD
mA
mA
V
IA, IB, and IW
CA, CB
CW
VINH
f = 1 MHz, measured to GND,
code = half scale
RAB = 10 kΩ
RAB = 100 kΩ
f = 1 MHz, measured to GND,
code = half scale
RAB = 10 kΩ
RAB = 100 kΩ
VA = V W = V B
−500
VLOGIC = 1.8 V to 2.3 V
VLOGIC = 2.3 V to 5.5 V
0.8 × VLOGIC
0.7 × VLOGIC
VINL
VHYST
IIN
CIN
VOH
VOL
Three-State Leakage Current
Three-State Output Capacitance
POWER SUPPLIES
Single-Supply Power Range
Dual-Supply Power Range
Logic Supply Range
Positive Supply Current
Test Conditions/Comments
25
12
pF
pF
12
5
±15
pF
pF
nA
+500
0.2 × VLOGIC
0.1 × VLOGIC
±1
5
RPULL-UP = 2.2 kΩ to VLOGIC
ISINK = 3 mA
ISINK = 6 mA, VLOGIC > 2.3 V
VLOGIC
−1
0.4
0.6
+1
V
V
V
µA
pF
5.5
±2.75
VDD
VDD
V
V
V
V
5.5
µA
nA
µA
mA
µA
µA
µW
dB
2
VSS = GND
IDD
ISS
IDD_EEPROM_STORE
IDD_EEPROM_READ
ILOGIC
PDISS
PSRR
Single supply, VSS = GND
Dual supply, VSS < GND
VIH = VLOGIC or VIL = GND
VDD = 5.5 V
VDD = 2.3 V
VIH = VLOGIC or VIL = GND
VIH = VLOGIC or VIL = GND
VIH = VLOGIC or VIL = GND
VIH = VLOGIC or VIL = GND
VIH = VLOGIC or VIL = GND
∆VDD/∆VSS = VDD ± 10%,
code = full scale
Rev. B | Page 4 of 32
2.3
±2.25
1.8
2.25
−5.5
0.7
400
−0.7
2
320
0.05
3.5
−66
V
V
V
V
µA
pF
1.4
−60
Data Sheet
Parameter
DYNAMIC CHARACTERISTICS9
Bandwidth
Total Harmonic Distortion
Resistor Noise Density
VW Settling Time
AD5122A/AD5142A
Symbol
Test Conditions/Comments
BW
−3 dB
RAB = 10 kΩ
RAB = 100 kΩ
VDD/VSS = ±2.5 V, VA = 1 V rms,
VB = 0 V, f = 1 kHz
RAB = 10 kΩ
RAB = 100 kΩ
Code = half scale, TA = 25°C,
f = 10 kHz
RAB = 10 kΩ
RAB = 100 kΩ
VA = 5 V, VB = 0 V, from
zero scale to full scale,
±0.5 LSB error band
RAB = 10 kΩ
RAB = 100 kΩ
RAB = 10 kΩ
RAB = 100 kΩ
THD
eN_WB
tS
Crosstalk (CW1/CW2)
CT
Analog Crosstalk
Endurance10
CTA
Min
TA = 25°C
Typ1
MHz
MHz
−80
−90
dB
dB
7
20
nV/√Hz
nV/√Hz
2
12
10
25
−90
1
µs
µs
nV-sec
nV-sec
dB
Mcycles
kcycles
Years
50
1
Unit
3
0.43
100
Data Retention11, 12
Max
Typical values represent average readings at 25°C, VDD = 5 V, VSS = 0 V, and VLOGIC = 5 V.
Resistor integral nonlinearity (R-INL) error is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. The maximum wiper current is limited to (0.7 × VDD)/RAB.
3
Guaranteed by design and characterization, not subject to production test.
4
INL and DNL are measured at VWB with the RDAC configured as a potentiometer divider similar to a voltage output DAC. VA = VDD and VB = 0 V. DNL specification limits
of ±1 LSB maximum are guaranteed monotonic operating conditions.
5
Resistor Terminal A, Resistor Terminal B, and Resistor Terminal W have no limitations on polarity with respect to each other. Dual-supply operation enables ground
referenced bipolar signal adjustment.
6
Different from operating current; supply current for EEPROM program lasts approximately 30 ms.
7
Different from operating current; supply current for EEPROM read lasts approximately 20 µs.
8
PDISS is calculated from (IDD × VDD) + (ILOGIC × VLOGIC).
9
All dynamic characteristics use VDD/VSS = ±2.5 V, and VLOGIC = 2.5 V.
10
Endurance is qualified to 100,000 cycles per JEDEC Standard 22, Method A117 and measured at −40°C to +125°C.
11
Retention lifetime equivalent at junction temperature (TJ) = 125°C per JEDEC Standard 22, Method A117. Retention lifetime, based on an activation energy of 1 eV,
derates with junction temperature in the Flash/EE memory.
12
50 years apply to an endurance of 1000 cycles. An endurance of 100,000 cycles has an equivalent retention lifetime of 5 years.
2
Rev. B | Page 5 of 32
AD5122A/AD5142A
Data Sheet
ELECTRICAL CHARACTERISTICS—AD5142A
VDD = 2.3 V to 5.5 V, VSS = 0 V; VDD = 2.25 V to 2.75 V, VSS = −2.25 V to −2.75 V; VLOGIC = 1.8 V to 5.5 V, −40°C < TA < +125°C, unless
otherwise noted.
Table 3.
Parameter
DC CHARACTERISTICS—RHEOSTAT
MODE (ALL RDACs)
Resolution
Resistor Integral Nonlinearity2
Resistor Differential Nonlinearity2
Nominal Resistor Tolerance
Resistance Temperature Coefficient3
Wiper Resistance3
Bottom Scale or Top Scale
Nominal Resistance Match
DC CHARACTERISTICS—POTENTIOMETER
DIVIDER MODE (ALL RDACs)
Integral Nonlinearity4
Differential Nonlinearity4
Full-Scale Error
Zero-Scale Error
Voltage Divider Temperature
Coefficient3
Symbol
Test Conditions/Comments
N
R-INL
Min
Typ1
Max
8
RAB = 10 kΩ
VDD ≥ 2.7 V
VDD < 2.7 V
RAB = 100 kΩ
VDD ≥ 2.7 V
VDD < 2.7 V
R-DNL
ΔRAB/RAB
(ΔRAB/RAB)/ΔT × 106
RW
Unit
Bits
−2
−5
±0.2
±1.5
+2
+5
LSB
LSB
−1
−2
−0.5
−8
±0.1
±0.5
±0.2
±1
35
+1
+2
+0.5
+8
LSB
LSB
LSB
%
ppm/°C
55
130
125
400
Ω
Ω
−1
40
60
±0.2
80
230
+1
Ω
Ω
%
RAB = 10 kΩ
RAB = 100 kΩ
−1
−0.5
−0.5
±0.2
±0.1
±0.2
+1
+0.5
+0.5
LSB
LSB
LSB
RAB = 10 kΩ
RAB = 100 kΩ
−2.5
−1
−0.1
±0.2
+1
LSB
LSB
Code = full scale
Code = zero scale
RAB = 10 kΩ
RAB = 100 kΩ
RBS or RTS
RAB = 10 kΩ
RAB = 100 kΩ
Code = 0xFF
RAB1/RAB2
INL
DNL
VWFSE
VWZSE
(ΔVW/VW)/ΔT × 106
RAB = 10 kΩ
RAB = 100 kΩ
Code = half scale
Rev. B | Page 6 of 32
1.2
0.5
±5
3
1
LSB
LSB
ppm/°C
Data Sheet
Parameter
RESISTOR TERMINALS
Maximum Continuous Current
Terminal Voltage Range5
Capacitance A, Capacitance B3
Capacitance W3
Common-Mode Leakage Current3
DIGITAL INPUTS
Input Logic3
High
Low
Input Hysteresis3
Input Current3
Input Capacitance3
DIGITAL OUTPUTS
Output High Voltage3
Output Low Voltage3
AD5122A/AD5142A
Symbol
Negative Supply Current
EEPROM Store Current3, 6
EEPROM Read Current3, 7
Logic Supply Current
Power Dissipation8
Power Supply Rejection Ratio
Min
RAB = 10 kΩ
RAB = 100 kΩ
−6
−1.5
VSS
Typ1
Max
Unit
+6
+1.5
VDD
mA
mA
V
IA, IB, and IW
CA, CB
CW
VINH
f = 1 MHz, measured to GND,
code = half scale
RAB = 10 kΩ
RAB = 100 kΩ
f = 1 MHz, measured to GND,
code = half scale
RAB = 10 kΩ
RAB = 100 kΩ
VA = V W = V B
−500
VLOGIC = 1.8 V to 2.3 V
VLOGIC = 2.3 V to 5.5 V
0.8 × VLOGIC
0.7 × VLOGIC
VINL
VHYST
IIN
CIN
VOH
VOL
Three-State Leakage Current
Three-State Output Capacitance
POWER SUPPLIES
Single-Supply Power Range
Dual-Supply Power Range
Logic Supply Range
Positive Supply Current
Test Conditions/Comments
25
12
pF
pF
12
5
±15
pF
pF
nA
+500
0.2 × VLOGIC
0.1 × VLOGIC
±1
5
RPULL-UP = 2.2 kΩ to VLOGIC
ISINK = 3 mA
ISINK = 6 mA, VLOGIC > 2.3 V
VLOGIC
−1
0.4
0.6
+1
V
V
V
µA
pF
5.5
±2.75
VDD
VDD
V
V
V
V
5.5
µA
nA
µA
mA
µA
µA
µW
dB
2
VSS = GND
IDD
ISS
IDD_EEPROM_STORE
IDD_EEPROM_READ
ILOGIC
PDISS
PSR
Single supply, VSS = GND
Dual supply, VSS < GND
VIH = VLOGIC or VIL = GND
VDD = 5.5 V
VDD = 2.3 V
VIH = VLOGIC or VIL = GND
VIH = VLOGIC or VIL = GND
VIH = VLOGIC or VIL = GND
VIH = VLOGIC or VIL = GND
VIH = VLOGIC or VIL = GND
∆VDD/∆VSS = VDD ± 10%,
code = full scale
Rev. B | Page 7 of 32
2.3
±2.25
1.8
2.25
−5.5
0.7
400
−0.7
2
320
0.05
3.5
−66
V
V
V
V
µA
pF
1.4
−60
AD5122A/AD5142A
Parameter
DYNAMIC CHARACTERISTICS9
Bandwidth
Total Harmonic Distortion
Resistor Noise Density
VW Settling Time
Data Sheet
Symbol
Test Conditions/Comments
BW
−3 dB
RAB = 10 kΩ
RAB = 100 kΩ
VDD/VSS = ±2.5 V, VA = 1 V rms,
VB = 0 V, f = 1 kHz
RAB = 10 kΩ
RAB = 100 kΩ
Code = half scale, TA = 25°C,
f = 10 kHz
RAB = 10 kΩ
RAB = 100 kΩ
VA = 5 V, VB = 0 V, from
zero scale to full scale,
±0.5 LSB error band
RAB = 10 kΩ
RAB = 100 kΩ
RAB = 10 kΩ
RAB = 100 kΩ
THD
eN_WB
tS
Crosstalk (CW1/CW2)
CT
Analog Crosstalk
Endurance10
CTA
Min
TA = 25°C
Typ1
MHz
MHz
−80
−90
dB
dB
7
20
nV/√Hz
nV/√Hz
2
12
10
25
−90
1
µs
µs
nV-sec
nV-sec
dB
Mcycles
kcycles
Years
50
1
Unit
3
0.43
100
Data Retention11, 12
Max
Typical values represent average readings at 25°C, VDD = 5 V, VSS = 0 V, and VLOGIC = 5 V.
Resistor integral nonlinearity (R-INL) error is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. The maximum wiper current is limited to (0.7 × VDD)/RAB.
3
Guaranteed by design and characterization, not subject to production test.
4
INL and DNL are measured at VWB with the RDAC configured as a potentiometer divider similar to a voltage output DAC. VA = VDD and VB = 0 V. DNL specification limits
of ±1 LSB maximum are guaranteed monotonic operating conditions.
5
Resistor Terminal A, Resistor Terminal B, and Resistor Terminal W have no limitations on polarity with respect to each other. Dual-supply operation enables ground
referenced bipolar signal adjustment.
6
Different from operating current; supply current for EEPROM program lasts approximately 30 ms.
7
Different from operating current; supply current for EEPROM read lasts approximately 20 µs.
8
PDISS is calculated from (IDD × VDD) + (ILOGIC × VLOGIC).
9
All dynamic characteristics use VDD/VSS = ±2.5 V, and VLOGIC = 2.5 V.
10
Endurance is qualified to 100,000 cycles per JEDEC Standard 22, Method A117 and measured at −40°C to +125°C.
11
Retention lifetime equivalent at junction temperature (TJ) = 125°C per JEDEC Standard 22, Method A117. Retention lifetime, based on an activation energy of 1 eV,
derates with junction temperature in the Flash/EE memory.
12
50 years apply to an endurance of 1000 cycles. An endurance of 100,000 cycles has an equivalent retention lifetime of 5 years.
2
Rev. B | Page 8 of 32
Data Sheet
AD5122A/AD5142A
INTERFACE TIMING SPECIFICATIONS
VLOGIC = 1.8 V to 5.5 V; all specifications TMIN to TMAX, unless otherwise noted.
Table 4.
Parameter1
fSCL2
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t11A
t12
tSP3
tRESET
tEEPROM_PROGRAM4
tEEPROM_READBACK
tPOWER_UP5
tRESET
Test Conditions/Comments
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Fast mode
Standard mode
Min
Fast mode
Standard mode
Fast mode
Fast mode
0.1
20 + 0.1 CL
Typ
4.0
0.6
4.7
1.3
250
100
0
0
4.7
0.6
4
0.6
4.7
1.3
4
0.6
Max
100
400
1000
300
300
300
1000
300
1000
Unit
kHz
kHz
µs
µs
µs
µs
ns
ns
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
ns
ns
ns
ns
ns
ns
ns
300
300
300
50
10
ns
ns
ns
ns
µs
50
30
75
ms
µs
µs
µs
3.45
0.9
20 + 0.1 CL
20 + 0.1 CL
20 + 0.1 CL
20 + 0.1 CL
0
15
7
30
1
Description
Serial clock frequency
SCL high time, tHIGH
SCL low time, tLOW
Data setup time, tSU; DAT
Data hold time, tHD; DAT
Setup time for a repeated start condition, tSU; STA
Hold time (repeated) for a start condition, tHD; STA
Bus free time between a stop and a start condition, tBUF
Setup time for a stop condition, tSU; STO
Rise time of SDA signal, tRDA
Fall time of SDA signal, tFDA
Rise time of SCL signal, tRCL
Rise time of SCL signal after a repeated start condition
and after an acknowledge bit, tRCL1 (not shown in Figure 3)
Fall time of SCL signal, tFCL
Pulse width of suppressed spike (not shown in Figure 3)
RESET low time (not shown in Figure 3)
Memory program time (not shown in Figure 3)
Memory readback time (not shown in Figure 3)
Power-on EEPROM restore time (not shown in Figure 3)
Reset EEPROM restore time (not shown in Figure 3)
Maximum bus capacitance is limited to 400 pF.
The SDA and SCL timing is measured with the input filters enabled. Switching off the input filters improves the transfer rate; however, it has a negative effect on the
EMC behavior of the part.
3
Input filtering on the SCL and SDA inputs suppresses noise spikes that are less than 50 ns for fast mode.
4
The EEPROM program time depends on the temperature and EEPROM write cycles. Higher timing is expected at lower temperatures and higher write cycles.
5
Maximum time after VDD − VSS is equal to 2.3 V.
2
Rev. B | Page 9 of 32
AD5122A/AD5142A
Data Sheet
SHIFT REGISTER AND TIMING DIAGRAMS
C3
C2
C1
C0
A3
A2
A1
DB8
DB7
A0
D7
DB0 (LSB)
D6
D5
D4
D3
D2
D1
D0
10939-002
DB15 (MSB)
DATA BITS
ADDRESS BITS
CONTROL BITS
Figure 2. Input Shift Register Contents
t11
t12
t6
t8
t2
SCL
t6
t5
t1
t4
t10
t3
t9
t7
P
S
S
Figure 3. I2C Serial Interface Timing Diagram (Typical Write Sequence)
Rev. B | Page 10 of 32
P
10939-003
SDA
Data Sheet
AD5122A/AD5142A
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 5.
Parameter
VDD to GND
VSS to GND
VDD to VSS
VLOGIC to GND
VA, VW, VB to GND
IA, IW, IB
Pulsed1
Frequency > 10 kHz
RAW = 10 kΩ
RAW = 100 kΩ
Frequency ≤ 10 kHz
RAW = 10 kΩ
RAW = 100 kΩ
Digital Inputs
Operating Temperature Range, TA3
Maximum Junction Temperature,
TJ Maximum
Storage Temperature Range
Reflow Soldering
Peak Temperature
Time at Peak Temperature
Package Power Dissipation
FICDM
Rating
−0.3 V to +7.0 V
+0.3 V to −7.0 V
7V
−0.3 V to VDD + 0.3 V or
+7.0 V (whichever is less)
VSS − 0.3 V, VDD + 0.3 V
+7.0 V (whichever is less)
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL RESISTANCE
θJA is defined by the JEDEC JESD51 standard, and the value is
dependent on the test board and test environment.
Table 6. Thermal Resistance
Package Type
16-Lead LFCSP
16-Lead TSSOP
±6 mA/d2
±1.5 mA/d2
1
±6 mA/√d2
±1.5 mA/√d2
−0.3 V to VLOGIC + 0.3 V or
+7 V (whichever is less)
−40°C to +125°C
150°C
θJA
89.51
150.41
JEDEC 2S2P test board, still air (0 m/sec airflow).
ESD CAUTION
−65°C to +150°C
260°C
20 sec to 40 sec
(TJ max − TA)/θJA
1.5 kV
1
Maximum terminal current is bounded by the maximum current handling of
the switches, maximum power dissipation of the package, and maximum
applied voltage across any two of the A, B, and W terminals at a given
resistance.
2
d = pulse duty factor.
3
Includes programming of EEPROM memory.
Rev. B | Page 11 of 32
θJC
3
27.6
Unit
°C/W
°C/W
AD5122A/AD5142A
Data Sheet
14 ADDR0
13 ADDR1
16 RESET
12 SDA
GND 1
11 SCL
10 VLOGIC
9
VDD
B2 8
TOP VIEW
(Not to Scale)
VSS 5
B1 4
W2 7
W1 3
AD5122A/
AD5142A
A2 6
A1 2
NOTES
1. EXPOSED PAD. CONNECT THE EXPOSED PAD TO THE
POTENTIAL OF THE VSS PIN, OR, ALTERNATIVELY, LEAVE IT
ELECTRICALLY UNCONNECTED. IT IS RECOMMENDED THAT
THE PAD BE THERMALLY CONNECTED TO A COPPER PLANE
FOR ENHANCED THERMAL PERFORMANCE.
10939-004
PIN 1
INDICATOR
15 INDEP
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 4. 16-Lead LFCSP Pin Configuration
Table 7. 16-Lead LFCSP Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mnemonic
GND
A1
W1
B1
VSS
A2
W2
B2
VDD
VLOGIC
SCL
SDA
ADDR1
ADDR0
INDEP
16
RESET
EPAD
Description
Ground Pin, Logic Ground Reference.
Terminal A of RDAC1. VSS ≤ VA ≤ VDD.
Wiper Terminal of RDAC1. VSS ≤ VW ≤ VDD.
Terminal B of RDAC1. VSS ≤ VB ≤ VDD.
Negative Power Supply. Decouple this pin with 0.1 μF ceramic capacitors and 10 μF capacitors.
Terminal A of RDAC2. VSS ≤ VA ≤ VDD.
Wiper Terminal of RDAC2. VSS ≤ VW ≤ VDD.
Terminal B of RDAC2. VSS ≤ VB ≤ VDD.
Positive Power Supply. Decouple this pin with 0.1 μF ceramic capacitors and 10 μF capacitors.
Logic Power Supply; 1.8 V to VDD. Decouple this pin with 0.1 μF ceramic capacitors and 10 μF capacitors.
Serial Clock Line.
Serial Data Input/Output.
Programmable Address (ADDR1) for Multiple Package Decoding.
Programmable Address (ADDR0) for Multiple Package Decoding.
Linear Gain Setting Mode at Power-Up. Each string resistor is loaded from its associated memory location.
If INDEP is enabled, it cannot be disabled by the software.
Hardware Reset Pin. Refresh the RDAC registers from EEPROM. RESET is activated at logic low.
If this pin is not used, tie RESET to VLOGIC.
Exposed Pad. Connect this exposed pad to the potential of the VSS pin, or, alternatively, leave it electrically
unconnected. It is recommended that the pad be thermally connected to a copper plane for enhanced
thermal performance.
Rev. B | Page 12 of 32
Data Sheet
AD5122A/AD5142A
INDEP
1
16
ADDR0
RESET
2
15
ADDR1
14
SDA
13
SCL
3
A1
4
W1
5
B1
6
AD5122A/
AD5142A
12 VLOGIC
TOP VIEW
(Not to Scale)
11 VDD
VSS
7
10
B2
A2
8
9
W2
10939-005
GND
Figure 5. 16-Lead TSSOP Pin Configuration
Table 8. 16-Lead TSSOP Pin Function Descriptions
Pin No.
1
Mnemonic
INDEP
2
RESET
3
4
5
6
7
8
9
10
11
12
13
14
15
16
GND
A1
W1
B1
VSS
A2
W2
B2
VDD
VLOGIC
SCL
SDA
ADDR1
ADDR0
Description
Linear Gain Setting Mode at Power-Up. Each string resistor is loaded from its associated memory location.
If INDEP is enabled, it cannot be disabled by the software.
Hardware Reset Pin. Refresh the RDAC registers from EEPROM. RESET is activated at logic low.
If this pin is not used, tie RESET to VLOGIC.
Ground Pin, Logic Ground Reference.
Terminal A of RDAC1. VSS ≤ VA ≤ VDD.
Wiper Terminal of RDAC1. VSS ≤ VW ≤ VDD.
Terminal B of RDAC1. VSS ≤ VB ≤ VDD.
Negative Power Supply. Decouple this pin with 0.1 µF ceramic capacitors and 10 µF capacitors.
Terminal A of RDAC2. VSS ≤ VA ≤ VDD.
Wiper Terminal of RDAC2. VSS ≤ VW ≤ VDD.
Terminal B of RDAC2. VSS ≤ VB ≤ VDD.
Positive Power Supply. Decouple this pin with 0.1 µF ceramic capacitors and 10 µF capacitors.
Logic Power Supply; 1.8 V to VDD. Decouple this pin with 0.1 µF ceramic capacitors and 10 µF capacitors.
Serial Clock Line.
Serial Data Input/Output.
Programmable Address (ADDR1) for Multiple Package Decoding.
Programmable Address (ADDR0) for Multiple Package Decoding.
Rev. B | Page 13 of 32
AD5122A/AD5142A
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
0.5
0.2
10kΩ, +125°C
10kΩ, +25°C
10kΩ, –40°C
100kΩ, +125°C
100kΩ, +25°C
100kΩ, –40°C
0.4
0.3
0.1
0
R-DNL (LSB)
R-INL (LSB)
0.2
0.1
0
–0.1
–0.1
–0.2
–0.3
–0.2
–0.4
–0.3
100
0
200
CODE (Decimal)
–0.6
10939-006
–0.5
10kΩ, +125°C
10kΩ, +25°C
10kΩ, –40°C
100kΩ, +125°C
100kΩ, +25°C
100kΩ, –40°C
100
0
200
CODE (Decimal)
Figure 6. R-INL vs. Code (AD5142A)
10939-009
–0.5
–0.4
Figure 9. R-DNL vs. Code (AD5142A)
0.20
0.10
0.15
0.05
0.10
0
R-DNL (LSB)
R-INL (LSB)
0.05
0
–0.05
–0.05
–0.10
–0.15
–0.10
10kΩ, +125°C
10kΩ, +25°C
10kΩ, –40°C
100kΩ, +125°C
100kΩ, +25°C
100kΩ, –40°C
–0.25
0
–0.25
50
100
CODE (Decimal)
–0.30
10kΩ, +125°C
10kΩ, +25°C
10kΩ, –40°C
0
100
Figure 10. R-DNL vs. Code (AD5122A)
0.10
10kΩ, –40°C
10kΩ, +25°C
10kΩ, +125°C
100kΩ, –40°C
100kΩ, +25°C
100kΩ, +125°C
0.2
50
CODE (Decimal)
Figure 7. R-INL vs. Code (AD5122A)
0.3
100kΩ, +125°C
100kΩ, +25°C
100kΩ, –40°C
10939-010
–0.20
–0.20
10939-007
–0.15
0.05
0
DNL (LSB)
0
–0.05
–0.10
–0.15
–0.1
–0.20
–0.2
–0.3
0
100
CODE (Decimal)
200
Figure 8. INL vs. Code (AD5142A)
–0.30
10kΩ, –40°C
10kΩ, +25°C
10kΩ, +125°C
0
100
CODE (Decimal)
Figure 11. DNL vs. Code (AD5142A)
Rev. B | Page 14 of 32
100kΩ, –40°C
100kΩ, +25°C
100kΩ, +125°C
200
10939-011
–0.25
10939-008
INL (LSB)
0.1
Data Sheet
AD5122A/AD5142A
0.15
1000
10kΩ, –40°C
10kΩ, +25°C
10kΩ, +125°C
100kΩ, –40°C
100kΩ, +25°C
100kΩ, +125°C
0.10
VLOGIC = 2.3V
VLOGIC = 3.3V
VLOGIC = 5.5V
800
700
0.05
600
ILOGIC (nA)
INL (LSB)
VDD = VLOGIC
VSS = GND
900
0
500
400
–0.05
300
200
–0.10
100
0
–40
CODE (Decimal)
–20
60
80
10kΩ, –40°C
10kΩ, +25°C
10kΩ, +125°C
0.04
0
250
–0.02
DNL (LSB)
0.02
300
200
150
100
120
–0.06
100
–0.08
50
–0.10
0
–0.12
0
50
100
150
200
255
AD5142A
0
25
50
75
CODE (Decimal)
100
127
AD5122A
100kΩ, –40°C
100kΩ, +25°C
100kΩ, +125°C
–0.04
–0.14
10939-013
POTENTIOMETER MODE TEMPERATURE
COEFFICIENT (ppm/°C)
0.06
350
–50
40
Figure 15. ILOGIC vs. Temperature
100kΩ
10kΩ
400
20
TEMPERATURE (°C)
Figure 12. INL vs. Code (AD5122A)
450
0
0
50
10939-015
50
10939-012
0
10939-160
100
–0.15
100
CODE (Decimal)
Figure 16. DNL vs. Code (AD5122A)
Figure 13. Potentiometer Mode Temperature Coefficient ((ΔVW/VW)/ΔT × 106)
vs. Code
450
600
400
300
200
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 14. IDD vs. Temperature
100
120
350
300
250
200
150
100
50
0
VDD = 2.3V
VDD = 3.3V
VDD = 5.5V
100
–50
10939-014
IDD (nA)
500
0
–40
10kΩ
100kΩ
400
0
50
100
150
200
255
AD5142A
0
25
50
75
CODE (Decimal)
100
127
AD5122A
Figure 17. Rheostat Mode Temperature Coefficient ((ΔRWB/RWB)/ΔT × 106)
vs. Code
Rev. B | Page 15 of 32
10939-016
700
VDD = VLOGIC
VSS = GND
RHEOSTAT MODE TEMPERATURE
COEFFICIENT (ppm/°C)
800
AD5122A/AD5142A
Data Sheet
1.2
1.0
0.8
0.6
0.4
–20
–40
–60
0.2
–80
1
2
3
4
5
DIGITAL INPUT VOLTAGE (V)
–100
10
10k
100k
1M
10M
10
0x80, (0x40)
0
–10 0x40, (0x20)
0x80, (0x40)
–10 0x40, (0x20)
0x20, (0x10)
0x20, (0x10)
–20 0x10, (0x08)
0x10, (0x08)
0x8, (0x04)
GAIN (dB)
GAIN (dB)
1k
Figure 21. Normalized Phase Flatness vs. Frequency, RAB = 10 kΩ
0
0x8, (0x04)
–30
100
FREQUENCY (Hz)
Figure 18. ILOGIC Current vs. Digital Input Voltage
–20
QUARTER SCALE
MIDSCALE
FULL-SCALE
10939-020
0
10939-017
0
VDD/VSS = ±2.5V
RAB = 10kΩ
0
PHASE (Degrees)
ILOGIC CURRENT (µA)
20
VLOGIC = 1.8V
VLOGIC = 2.3V
VLOGIC = 3.3V
VLOGIC = 5V
VLOGIC = 5.5V
0x4, (0x02)
0x2, (0x01)
–40 0x1, (0x00)
–30 0x4, (0x02)
–40
–50
0x2, (0x01)
0x1, (0x00)
0x00
–60
0x00
–70
–50
–80
AD5142A (AD5122A)
AD5142A (AD5122A)
1k
10k
100k
1M
10M
FREQUENCY (Hz)
–90
10
100
0
–20
–30
THD + N (dB)
THD + N (dB)
10M
10kΩ
100kΩ
–10
–60
–70
–80
–40
–50
–60
–70
–90
–80
200
2k
FREQUENCY (Hz)
20k
200k
Figure 20. Total Harmonic Distortion Plus Noise (THD + N) vs. Frequency
VDD/VSS = ±2.5V
fIN = 1kHz
CODE = HALF SCALE
NOISE FILTER = 22kHz
–90
0.001
10939-019
–100
20
1M
0.01
0.1
VOLTAGE (V rms)
1
10939-022
–50
100k
Figure 22. 100 kΩ Gain vs. Frequency and Code
10kΩ
100kΩ
VDD/VSS = ±2.5V
VA = 1V rms
VB = GND
CODE = HALF SCALE
NOISE FILTER = 22kHz
10k
FREQUENCY (Hz)
Figure 19. 10 kΩ Gain vs. Frequency and Code
–40
1k
10939-021
100
10939-018
–60
10
Figure 23. Total Harmonic Distortion Plus Noise (THD + N) vs. Amplitude
Rev. B | Page 16 of 32
Data Sheet
AD5122A/AD5142A
0.8
0
0.7
–10
0.6
RELATIVE VOLTAGE (V)
10
–30
–40
–50
–60
0.5
0.4
0.3
0.2
0.1
–70
1k
10k
100k
1M
FREQUENCY (Hz)
–0.1
Figure 27. Maximum Transition Glitch
400
300
1.2
1.0
0.0020
PROBABILITY DENSITY
WIPER ON RESISTANCE (Ω)
0.0025
100kΩ, V DD = 2.3V
100kΩ, V DD = 2.7V
100kΩ, V DD = 3V
100kΩ, V DD = 3.6V
100kΩ, V DD = 5V
100kΩ, V DD = 5.5V
10kΩ, VDD = 2.3V
10kΩ, VDD = 2.7V
10kΩ, VDD = 3V
10kΩ, VDD = 3.6V
10kΩ, VDD = 5V
10kΩ, VDD = 5.5V
500
15
10
TIME (µs)
Figure 24. Normalized Phase Flatness vs. Frequency, RAB = 100 kΩ
600
5
0
200
0.8
0.0015
0.6
0.0010
0.4
0.0005
0.2
100
0
1
2
3
4
5
VOLTAGE (V)
0
0
–600 –500 –400 –300 –200 –100
10939-024
0
0
10kΩ + 0pF
10kΩ + 75pF
10kΩ + 150pF
10kΩ + 250pF
100kΩ + 0pF
100kΩ + 75pF
100kΩ + 150pF
100kΩ + 250pF
–10
200
300
400
500
600
10kΩ
100kΩ
VDD = 5V ±10% AC
VSS = GND, VA = 4V, VB = GND
CODE = MIDSCALE
–20
–30
PSRR (dB)
6
5
4
–40
–50
–60
3
–70
2
–90
10
0
0
0
20
10
40
20
60
80
30
40
CODE (Decimal)
100
50
120 AD5142A
60
AD5122A
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 29. Power Supply Rejection Ratio (PSRR) vs. Frequency
Figure 26. Maximum Bandwidth vs. Code and Net Capacitance
Rev. B | Page 17 of 32
10939-028
–80
1
10939-025
BANDWIDTH (MHz)
7
100
Figure 28. Resistor Lifetime Drift
10
8
0
RESISTOR DRIFT (ppm)
Figure 25. Incremental Wiper On Resistance vs. VDD
9
10939-026
100
10939-023
–90
10
0
VDD/VSS = ±2.5V
RAB = 100kΩ
CUMULATIVE PROBABILITY
QUARTER SCALE
MIDSCALE
FULL-SCALE
–80
10939-027
PHASE (Degrees)
–20
0x80 TO 0x7F, 100kΩ
0x80 TO 0x7F, 10kΩ
Data Sheet
0.020
7
0.015
6
0.010
THEORETICAL IMAX (mA)
RELATIVE VOLTAGE (V)
AD5122A/AD5142A
0.005
0
–0.005
–0.010
5
4
3
2
10kΩ
1
–0.015
1500
1000
500
2000
TIME (ns)
Figure 30. Digital Feedthrough
0
10kΩ
100kΩ
SHUTDOWN MODE ENABLED
–60
–80
–100
1k
10k
100k
1M
FREQUECNY (Hz)
10M
10939-030
GAIN (dB)
–40
100
0
50
100
0
25
50
75
CODE (Decimal)
150
200
100
250 AD5142A
125 AD5122A
Figure 32. Theoretical Maximum Current vs. Code
–20
–120
10
0
Figure 31. Shutdown Isolation vs. Frequency
Rev. B | Page 18 of 32
10939-031
0
10939-029
100kΩ
–0.020
Data Sheet
AD5122A/AD5142A
TEST CIRCUITS
Figure 33 to Figure 37 define the test conditions used in the Specifications section.
NC
VA
IW
V+ = VDD ±10%
VDD
B
V+
VMS
~
Figure 33. Resistor Integral Nonlinearity Error (Rheostat Operation; R-INL, R-DNL)
PSRR (dB) = 20 LOG
W
B
10939-032
NC = NO CONNECT
A
VMS
PSS (%/%) =
RSW =
ΔVDD%
0.1V
ISW
CODE = 0x00
W
V+
B
VMS
A = NC
NC
IW = VDD/RNOMINAL
DUT
W
VW
B
RW = VMS1/IW
NC = NO CONNECT
10939-034
VMS1
–
VSS TO VDD
Figure 37. Incremental On Resistance
Figure 34. Potentiometer Divider Nonlinearity Error (INL, DNL)
A
0.1V
ISW
10939-036
W
+
B
V+ = VDD
1LSB = V+/2N
10939-033
DUT
A
Figure 35. Wiper Resistance
Rev. B | Page 19 of 32
ΔVMS
ΔVDD
)
ΔVMS%
Figure 36. Power Supply Sensitivity and
Power Supply Rejection Ratio (PSS, PSRR)
DUT
(
10939-035
DUT
A
W
AD5122A/AD5142A
Data Sheet
THEORY OF OPERATION
The AD5122A/AD5142A digital programmable potentiometers
are designed to operate as true variable resistors for analog signals
within the terminal voltage range of VSS < VTERM < VDD. The resistor
wiper position is determined by the RDAC register contents. The
RDAC register acts as a scratchpad register that allows unlimited
changes of resistance settings. A secondary register (the input
shift register) can be used to preload the RDAC register data.
The RDAC register can be programmed with any position setting
using the I2C interface. When a desirable wiper position is found,
this value can be stored in the EEPROM memory. Thereafter,
the wiper position is always restored to that position for subsequent
power-ups. The storing of EEPROM data takes approximately
15 ms; during this time, the device is locked and does not
acknowledge any new command, preventing any changes from
taking place.
I2C SERIAL DATA INTERFACE
The AD5122A/AD5142A have 2-wire, I2C-compatible serial
interfaces. The device can be connected to an I2C bus as a slave
device, under the control of a master device. See Figure 3 for a
timing diagram of a typical write sequence.
The AD5122A/AD5142A supports standard (100 kHz) and fast
(400 kHz) data transfer modes. Support is not provided for 10-bit
addressing and general call addressing.
The 2-wire serial bus protocol operates as follows:
1.
RDAC REGISTER AND EEPROM
The RDAC register directly controls the position of the digital
potentiometer wiper. For example, when the RDAC register is
loaded with 0x80 (AD5142A, 256 taps), the wiper is connected
to half scale of the variable resistor. The RDAC register is a standard
logic register; there is no restriction on the number of changes
allowed.
It is possible to both write to and read from the RDAC register
using the digital interface (see Table 10).
2.
The contents of the RDAC register can be stored to the EEPROM
using Command 9 (see Table 10). Thereafter, the RDAC register
always sets at that position for any future on-off-on power
supply sequence. It is possible to read back data saved into the
EEPROM with Command 3 (see Table 10).
3.
Alternatively, the EEPROM can be written to independently
using Command 11 (see Table 16).
INPUT SHIFT REGISTER
For the AD5122A/AD5142A, the input shift register is 16 bits
wide, as shown in Figure 2. The 16-bit word consists of four
control bits, followed by four address bits and by eight data bits.
If the AD5122A RDAC or EEPROM registers are read from or
written to, the lowest data bit (Bit 0) is ignored.
Data is loaded MSB first (Bit 15). The four control bits determine
the function of the software command, as listed in Table 10 and
Table 16.
The master initiates a data transfer by establishing a start
condition, which is when a high-to-low transition on the
SDA line occurs while SCL is high. The following byte is
the address byte, which consists of the 7-bit slave address
and an R/W bit. The slave device corresponding to the
transmitted address responds by pulling SDA low during
the ninth clock pulse (this is called the acknowledge bit).
At this stage, all other devices on the bus remain idle while
the selected device waits for data to be written to, or read
from, its shift register.
If the R/W bit is set high, the master reads from the slave
device. However, if the R/W bit is set low, the master writes
to the slave device.
Data is transmitted over the serial bus in sequences of nine
clock pulses (eight data bits followed by an acknowledge bit).
The transitions on the SDA line must occur during the low
period of SCL and remain stable during the high period of SCL.
When all data bits have been read from or written to, a stop
condition is established. In write mode, the master pulls the
SDA line high during the tenth clock pulse to establish a stop
condition. In read mode, the master issues a no acknowledge
for the ninth clock pulse (that is, the SDA line remains high).
The master then brings the SDA line low before the tenth
clock pulse, and then high again during the tenth clock pulse
to establish a stop condition.
I2C ADDRESS
The facility to make hardwired changes to ADDR allows the
user to incorporate up to nine of these devices on one bus as
outlined in Table 9.
Table 9. Device Address Selection
ADDR0 Pin
VLOGIC
No connect1
GND
VLOGIC
No connect1
GND
VLOGIC
No connect1
GND
1
ADDR1 Pin
VLOGIC
VLOGIC
VLOGIC
No connect1
No connect1
No connect1
GND
GND
GND
7-Bit I2C Device Address
0100000
0100010
0100011
0101000
0101010
0101011
0101100
0101110
0101111
Not available in bipolar mode (VSS < 0 V) or in low voltage mode (VLOGIC = 1.8 V).
Rev. B | Page 20 of 32
Data Sheet
AD5122A/AD5142A
Table 10. Reduced Commands Operation Truth Table
Command
Number
0
1
Control
Bits[DB15:DB12]
C3 C2 C1 C0
0
0
0
0
0
0
0
1
Address
Bits[DB11:DB8]1
A3 A2 A1 A0
X
X
X
X
0
0
0
A0
2
0
0
1
0
0
0
0
3
0
0
1
1
0
0
9
10
14
15
0
0
1
1
1
1
0
1
1
1
1
0
1
1
1
0
0
0
X
A3
0
0
X
0
1
D7
X
D7
Data Bits[DB7:DB0]1
D6 D5 D4 D3 D2 D1
X
X
X
X
X
X
D6 D5 D4 D3 D2 D1
D0
X
D0
A0
D7
D6
D5
D4
D3
D2
D1
D0
A1
A0
X
X
X
X
X
X
D1
D0
0
0
X
0
A0
A0
X
A0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1
0
X
D0
Operation
NOP: do nothing
Write contents of serial register
data to RDAC
Write contents of serial register
data to input shift register
Read back contents
D1
D0
Data
0
1
EEPROM
1
1
RDAC
Copy RDAC register to EEPROM
Copy EEPROM into RDAC
Software reset
Software shutdown
D0
Condition
0
Normal mode
1
Shutdown mode
X = don’t care.
Table 11. Reduced Address Bits Table
A3
1
0
0
0
1
A2
X1
0
0
0
A1
X1
0
0
1
A0
X1
0
1
0
Channel
All channels
RDAC1
RDAC2
Not applicable
X = don’t care.
Rev. B | Page 21 of 32
Stored Channel Memory
Not applicable
RDAC1
Not applicable
RDAC2
AD5122A/AD5142A
Data Sheet
ADVANCED CONTROL MODES
Low Wiper Resistance Feature
The AD5122A/AD5142A digital potentiometers include a set
of user programming features to address the wide number of
applications for these universal adjustment devices (see Table 16
and Table 18).
The AD5122A/AD5142A include two commands to reduce the
wiper resistance between the terminals when the device achieves
full scale or zero scale. These extra positions are called bottom
scale, BS, and top scale, TS. The resistance between Terminal A
and Terminal W at top scale is specified as RTS. Similarly, the
bottom scale resistance between Terminal B and Terminal W is
specified as RBS.
Key programming features include the following:
•
•
•
•
•
•
•
•
Input register
Linear gain setting mode
A low wiper resistance feature
Linear increment and decrement instructions
±6 dB increment and decrement instructions
Burst mode
Reset
Shutdown mode
The contents of the RDAC registers are unchanged by entering
in these positions. There are three ways to exit from top scale
and bottom scale: by using Command 12 or Command 13
(see Table 16); by loading new data in an RDAC register, which
includes increment/decrement operations; or by entering
shutdown mode, Command 15 (see Table 16).
Input Register
The AD5122A/AD5142A include one input register per RDAC
register. These registers allow preloading of the value for the
associated RDAC register. These registers can be written to using
Command 2 and read back from using Command 3 (see Table 16).
This feature allows a synchronous update of one or both RDAC
registers at the same time.
Table 12 and Table 13 show the truth tables for the top scale
position and the bottom scale position, respectively, when
potentiometer or linear gain setting mode is enabled.
Table 12. Top Scale Truth Table
Linear Gain Setting Mode
RAW
RWB
RAB
RAB
RAW
RTS
Potentiometer Mode
RWB
RAB
Table 13. Bottom Scale Truth Table
The transfer from the input register to the RDAC register is
done synchronously by Command 8 (see Table 16).
If new data is loaded in an RDAC register, this RDAC register
automatically overwrites the associated input register.
Linear Gain Setting Mode
The proprietary architecture of the AD5122A/AD5142A allows
the independent control of each string resistor, RAW, and RWB. To
enable linear gain setting mode, use Command 16 (see Table 16)
to set Bit D2 of the control register (see Table 18).
This mode of operation can control the potentiometer as two
independent rheostats connected at a single point, W terminal,
as opposed to potentiometer mode where each resistor is
complementary, RAW = RAB − RWB.
This mode enables a second input and an RDAC register per
channel, as shown in Table 16; however, the actual RDAC
contents remain unchanged. The same operations are valid for
potentiometer and linear gain setting mode.
Linear Gain Setting Mode
RAW
RWB
RTS
RBS
RAW
RAB
Potentiometer Mode
RWB
RBS
Linear Increment and Decrement Instructions
The increment and decrement commands (Command 4 and
Command 5 in Table 16) are useful for linear step adjustment
applications. These commands simplify microcontroller software
coding by allowing the controller to send an increment or
decrement command to the device. The adjustment can be
individual or in a ganged potentiometer arrangement, where
all wiper positions are changed at the same time.
For an increment command, executing Command 4 automatically
moves the wiper to the next RDAC position. This command can
be executed in a single channel or in multiple channels.
If the INDEP pin is pulled high, the device powers up in linear
gain setting mode and loads the values stored in the associated
memory locations for each channel (see Table 17). The INDEP pin
and the D2 bit are connected internally to a logic OR gate; if one or
both are set to 1, the parts cannot operate in potentiometer mode.
Rev. B | Page 22 of 32
Data Sheet
AD5122A/AD5142A
±6 dB Increment and Decrement Instructions
Reset
Two programming instructions produce logarithmic taper
increment or decrement of the wiper position control by
an individual potentiometer or by a ganged potentiometer
arrangement where all RDAC register positions are changed
simultaneously. The +6 dB increment is activated by Command 6,
and the −6 dB decrement is activated by Command 7 (see Table 16).
For example, starting with the zero-scale position and executing
Command 6 ten times moves the wiper in 6 dB steps to the fullscale position. When the wiper position is near the maximum
setting, the last 6 dB increment instruction causes the wiper to go
to the full-scale position (see Table 14).
The AD5122A/AD5142A can be reset through software by
executing Command 14 (see Table 16) or through hardware on
the low pulse of the RESET pin. The reset command loads the
RDAC registers with the contents of the EEPROM and takes
approximately 30 µs. The EEPROM is preloaded to midscale at
the factory, and initial power-up is, accordingly, at midscale.
Tie RESET to VLOGIC if the RESET pin is not used.
Incrementing the wiper position by +6 dB essentially doubles
the RDAC register value, whereas decrementing the wiper
position by −6 dB halves the register value. Internally, the
AD5122A/AD5142A use shift registers to shift the bits left and
right to achieve a ±6 dB increment or decrement. These functions
are useful for various audio/video level adjustments, especially for
white LED brightness settings in which human visual responses
are more sensitive to large adjustments than to small adjustments.
Table 14. Detailed Left Shift and Right Shift Functions for
the ±6 dB Step Increment and Decrement
Left Shift (+6 dB/Step)
0000 0000
0000 0001
0000 0010
0000 0100
0000 1000
0001 0000
0010 0000
0100 0000
1000 0000
1111 1111
Right Shift (−6 dB/Step)
1111 1111
0111 1111
0011 1111
0001 1111
0000 1111
0000 0111
0000 0011
0000 0001
0000 0000
0000 0000
The AD5122A/AD5142A can be placed in shutdown mode by
executing the software shutdown command, Command 15 (see
Table 16), and setting the LSB (D0) to 1. This feature places the
RDAC in a zero power consumption state where the device
operates in potentiometer mode, Terminal A is open-circuited
and the wiper, Terminal W, is connected to Terminal B; however, a
finite wiper resistance of 40 Ω is present. When the device is
configured in linear gain setting mode, the resistor addressed,
RAW or RWB, is internally placed at high impedance. Table 15
shows the truth table depending on the device operating mode.
The contents of the RDAC register are unchanged by entering
shutdown mode. However, all commands listed in Table 16 are
supported while in shutdown mode. Execute Command 15 (see
Table 16) and set the LSB (D0) to 0 to exit shutdown mode.
Table 15. Truth Table for Shutdown Mode
Linear Gain Setting Mode
RAW
RWB
High impedance
High impedance
Potentiometer Mode
RAW
RWB
High impedance
RBS
EEPROM OR RDAC REGISTER PROTECTION
The EEPROM and RDAC registers can be protected by disabling
any update to these registers. This can be done by using software. If
these registers are protected by software, set Bit D0 and/or Bit D1
(see Table 18), which protects the RDAC and EEPROM registers
independently.
Burst Mode
By enabling the burst mode, multiple data bytes can be sent to
the part consecutively. After the command byte, the part
interprets the following consecutive bytes as data bytes for the
command.
A new command can be sent by generating a repeat start or by a
stop and start condition.
The burst mode is activated by setting Bit D3 of the control
register (see Table 18).
Shutdown Mode
When RDAC is protected, the only operation allowed is to copy
the EEPROM into the RDAC register.
INDEP PIN
If the INDEP pin is pulled high at power-up, the part operates
in linear gain setting mode, loading each string resistor, RAWX and
RWBX, with the value stored into the EEPROM (see Table 17). If
the pin is pulled low, the part powers up in potentiometer mode.
The INDEP pin and the D2 bit are connected internally to a logic
OR gate; if one or both are set to 1, the part cannot operate in
potentiometer mode (see Table 18).
Rev. B | Page 23 of 32
AD5122A/AD5142A
Data Sheet
Table 16. Advanced Command Operation Truth Table
Command
Number
0
1
Command
Bits[DB15:DB12]
C3
C2
C1
C0
0
0
0
0
0
0
0
1
Address
Bits[DB11:DB8]1
A3 A2 A1 A0
X
X
X
X
0
A2 0
A0
D7
X
D7
2
0
0
1
0
0
A2
0
A0
3
0
0
1
1
X
A2
A1
4
5
6
7
8
0
0
0
0
0
1
1
1
1
1
0
0
0
0
1
0
0
1
1
0
A3
A3
A3
A3
0
A2
A2
A2
A2
A2
9
0
1
1
1
0
10
11
0
1
1
0
1
0
1
0
12
1
0
0
13
1
0
14
15
1
1
16
1
1
D6
X
D6
Data Bits[DB7:DB0]1
D5 D4 D3 D2 D1
X
X
X
X
X
D5 D4 D3 D2 D1
D0
X
D0
D7
D6
D5
D4
D3
D2
D1
D0
A0
X
X
X
X
X
X
D1
D0
0
0
0
0
0
A0
A0
A0
A0
A0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1
0
1
0
X
A2
0
A0
X
X
X
X
X
X
X
1
0
0
A2
0
0
A1
A0
A0
X
D7
X
D6
X
D5
X
D4
X
D3
X
D2
X
D1
0
D0
1
A3
A2
0
A0
1
X
X
X
X
X
X
D0
0
1
A3
A2
0
A0
0
X
X
X
X
X
X
D0
0
1
1
0
1
0
X
A3
X
A2
X
0
X
A0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
D0
1
0
1
X
X
X
X
X
X
X
X
D3
D2
D1
D0
Operation
NOP: do nothing
Write contents of serial
register data to RDAC
Write contents of serial
register data to input
register
Read back contents
D1
D0
Data
0
0
Input register
0
1
EEPROM
1
0
Control
register
1
1
RDAC
Linear RDAC increment
Linear RDAC decrement
+6 dB RDAC increment
−6 dB RDAC decrement
Copy input register to RDAC
(software LRDAC)
Copy RDAC register to
EEPROM
Copy EEPROM into RDAC
Write contents of serial
register data to EEPROM
Top scale
D0 = 0; normal mode
D0 = 1; shutdown mode
Bottom scale
D0 = 1; enter
D0 = 0; exit
Software reset
Software shutdown
D0 = 0; normal mode
D0 = 1; device placed in
shutdown mode
Copy serial register data to
control register
X = don’t care.
Table 17. Address Bits
A3
1
0
0
0
0
0
0
1
A2
X1
0
1
0
1
0
0
A1
X1
0
0
0
0
1
1
A0
X1
0
0
1
1
0
1
Potentiometer Mode
Input Register
RDAC Register
All channels
All channels
RDAC1
RDAC1
Not applicable
Not applicable
RDAC2
RDAC2
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Linear Gain Setting Mode
Input Register
RDAC Register
All channels
All channels
RWB1
RWB1
RAW1
RAW1
RWB2
RWB2
RAW2
RAW2
Not applicable
Not applicable
Not applicable
Not applicable
X = don’t care.
Rev. B | Page 24 of 32
Stored Channel
Memory
Not applicable
RDAC1/RWB1
Not applicable
RAW1
Not applicable
RDAC2/RWB2
RAW2
Data Sheet
AD5122A/AD5142A
Table 18. Control Register Bit Descriptions
Bit Name
D0
D1
D2
D3
Description
RDAC register write protect
0 = wiper position frozen to value in EEPROM memory
1 = allows update of wiper position through digital interface (default)
EEPROM program enable
0 = EEPROM program disabled
1 = enables device for EEPROM program (default)
Linear setting mode/potentiometer mode
0 = potentiometer mode (default)
1 = linear gain setting mode
Burst mode (I2C only)
0 = disabled (default)
1 = enabled (no disable after stop or repeated start condition)
Rev. B | Page 25 of 32
AD5122A/AD5142A
Data Sheet
RDAC ARCHITECTURE
PROGRAMMING THE VARIABLE RESISTOR
To achieve optimum performance, Analog Devices, Inc., has
proprietary RDAC segmentation architecture for all the digital
potentiometers. In particular, the AD5122A/AD5142A employ
a three-stage segmentation approach, as shown in Figure 38.
The AD5122A/AD5142A wiper switch is designed with the
transmission gate CMOS topology and with the gate voltage
derived from VDD and VSS.
Rheostat Operation—±8% Resistor Tolerance
A
A
W
STS
B
RL
W
B
AD5122A:
RL
RWB (D )
RM
RH
D
R AB RW
128
From 0x00 to 0x7F
(1)
D
R AB RW
256
From 0x00 to 0xFF
(2)
AD5142A:
RM
RH
B
W
The nominal resistance between Terminal A and Terminal B,
RAB, is 10 kΩ or 100 kΩ, and has 128/256 tap points accessed by
the wiper terminal. The 7-bit/8-bit data in the RDAC latch is
decoded to select one of the 128/256 possible wiper settings. The
general equations for determining the digitally programmed
output resistance between Terminal W and Terminal B are
RM
RM
7-BIT/8-BIT
ADDRESS
DECODER
W
Figure 39. Rheostat Mode Configuration
RH
RH
A
10939-038
A
The AD5122A/AD5142A operate in rheostat mode when only two
terminals are used as a variable resistor. The unused terminal can
be floating, or it can be tied to Terminal W, as shown in Figure 39.
RWB (D )
SBS
10939-037
B
Figure 38. AD5122A/AD5142A Simplified RDAC Circuit
Top Scale/Bottom Scale Architecture
In addition, the AD5122A/AD5142A include new positions to
reduce the resistance between terminals. These positions are
called bottom scale and top scale. At bottom scale, the typical
wiper resistance decreases from 130 Ω to 60 Ω (RAB = 100 kΩ).
At top scale, the resistance between Terminal A and Terminal W
is decreased by 1 LSB, and the total resistance is reduced to
60 Ω (RAB = 100 kΩ).
where:
D is the decimal equivalent of the binary code in the 7-bit/8-bit
RDAC register.
RAB is the end-to-end resistance.
RW is the wiper resistance.
In potentiometer mode, similar to the mechanical potentiometer,
the resistance between Terminal W and Terminal A also
produces a digitally controlled complementary resistance, RWA.
RWA also gives a maximum of 8% absolute resistance error. RWA
starts at the maximum resistance value and decreases as the data
loaded into the latch increases. The general equations for this
operation are
AD5122A:
RAW (D )
128 D
RAB RW
128
From 0x00 to 0x7F
256 D
RAB RW
256
From 0x00 to 0xFF (4)
(3)
AD5142A:
RAW (D )
where:
D is the decimal equivalent of the binary code in the 7-bit/8-bit
RDAC register.
RAB is the end-to-end resistance.
RW is the wiper resistance.
Rev. B | Page 26 of 32
Data Sheet
AD5122A/AD5142A
If the part is configured in linear gain setting mode, the resistance
between Terminal W and Terminal A is directly proportional
to the code loaded in the associate RDAC register. The general
equations for this operation are
AD5122A:
R AW (D)
D
R AB RW
128
From 0x00 to 0x7F (5)
AD5142A:
TERMINAL VOLTAGE OPERATING RANGE
The AD5122A/AD5142A are designed with internal ESD diodes
for protection. These diodes also set the voltage boundary of
the terminal operating voltages. Positive signals present on
Terminal A, Terminal B, or Terminal W that exceed VDD are
clamped by the forward-biased diode. There is no polarity
constraint between VA, VW, and VB, but they cannot be higher
than VDD or lower than VSS.
VDD
From 0x00 to 0xFF (6)
A
where:
D is the decimal equivalent of the binary code in the 7-bit/8-bit
RDAC register.
RAB is the end-to-end resistance.
RW is the wiper resistance.
In the bottom scale condition or top scale condition, a finite
total wiper resistance of 40 Ω is present. Regardless of which
setting the part is operating in, limit the current between
Terminal A to Terminal B, Terminal W to Terminal A, and
Terminal W to Terminal B, to the maximum continuous
current or to the pulse current specified in Table 5. Otherwise,
degradation or possible destruction of the internal switch
contact can occur.
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates a voltage divider at
wiper-to-B and wiper-to-A that is proportional to the input voltage
at A to B, as shown in Figure 40.
Figure 41. Maximum Terminal Voltages Set by VDD and VSS
POWER-UP SEQUENCE
Because there are diodes to limit the voltage compliance at
Terminal A, Terminal B, and Terminal W (see Figure 41), it is
important to power up VDD first before applying any voltage to
Terminal A, Terminal B, and Terminal W. Otherwise, the diode
is forward-biased such that VDD is powered unintentionally. The
ideal power-up sequence is VSS, VDD, VLOGIC, digital inputs, and
VA, VB, and VW. The order of powering VA, VB, VW, and digital
inputs is not important as long as they are powered after VSS,
VDD, and VLOGIC. Regardless of the power-up sequence and the
ramp rates of the power supplies, once VDD is powered, the
power-on preset activates, which restores EEPROM values to
the RDAC registers.
LAYOUT AND POWER SUPPLY BIASING
VOUT
B
Figure 40. Potentiometer Mode Configuration
Connecting Terminal A to 5 V and Terminal B to ground
produces an output voltage at the Wiper W to Terminal B
ranging from 0 V to 5 V. The general equation defining the
output voltage at VW with respect to ground for any valid
input voltage applied to Terminal A and Terminal B is
VW (D )
VSS
R (D)
RWB (D )
VA AW
VB
RAB
RAB
(7)
It is always a good practice to use a compact, minimum lead
length layout design. Ensure that the leads to the input are as
direct as possible with a minimum conductor length. Ground
paths should have low resistance and low inductance. It is also
good practice to bypass the power supplies with quality capacitors.
Apply low equivalent series resistance (ESR) 1 μF to 10 μF
tantalum or electrolytic capacitors at the supplies to minimize
any transient disturbance and to filter low frequency ripple.
Figure 42 illustrates the basic supply bypassing configuration
for the AD5122A/AD5142A.
VDD
where:
RWB(D) can be obtained from Equation 1 and Equation 2.
RAW(D) can be obtained from Equation 3 and Equation 4.
Operation of the digital potentiometer in the divider mode
results in a more accurate operation over temperature. Unlike
the rheostat mode, the output voltage is dependent mainly on
the ratio of the internal resistors, RAW and RWB, and not the
absolute values. Therefore, the temperature drift reduces to
5 ppm/°C.
VSS
Rev. B | Page 27 of 32
+
C3
10µF
C1
0.1µF
+
C4
10µF
C2
0.1µF
VDD
VLOGIC
AD5122A/
AD5142A
C5
0.1µF
C6
10µF
+
VLOGIC
VSS
GND
10939-041
W
VB
B
A
10939-039
VA
W
10939-040
D
R AW (D )
R AB RW
256
Figure 42. Power Supply Bypassing
AD5122A/AD5142A
Data Sheet
OUTLINE DIMENSIONS
3.10
3.00 SQ
2.90
0.50
BSC
13
PIN 1
INDICATOR AREA OPTIONS
16
(SEE DETAIL A)
12
1
1.75
1.60 SQ
1.45
EXPOSED
PAD
9
0.50
0.40
0.30
TOP VIEW
0.80
0.75
0.70
TOP VIEW
5
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
PKG-005138
4
8
0.20 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
02-23-2017-E
PIN 1
INDICATOR
DETAIL A
(JEDEC 95)
0.30
0.23
0.18
COMPLIANT TO JEDEC STANDARDS MO-220-WEED-6.
Figure 43. 16-Lead Lead Frame Chip Scale Package [LFCSP]
3 mm × 3 mm Body and 0.75 mm Package Height
(CP-16-22)
Dimensions shown in millimeters
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.65
BSC
0.30
0.19
COPLANARITY
0.10
SEATING
PLANE
8°
0°
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 44. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
Rev. B | Page 28 of 32
0.75
0.60
0.45
Data Sheet
AD5122A/AD5142A
ORDERING GUIDE
Model1, 2, 3
AD5122ABCPZ10-RL7
AD5122ABCPZ100-RL7
AD5122AWBCPZ10-RL7
AD5122ABRUZ10
AD5122ABRUZ100
AD5122ABRUZ10-RL7
AD5122ABRUZ100-RL7
AD5142ABCPZ10-RL7
AD5142ABCPZ100-RL7
AD5142AWBCPZ10-RL7
AD5142ABRUZ10
AD5142ABRUZ100
AD5142ABRUZ10-RL7
AD5142ABRUZ100-RL7
EVAL-AD5142ADBZ
RAB (kΩ)
10
100
10
10
100
10
100
10
100
10
10
100
10
100
Resolution
128
128
128
128
128
128
128
256
256
256
256
256
256
256
Interface
I2 C
I2 C
I2 C
I2 C
I2 C
I2 C
I2 C
I2 C
I2 C
I2 C
I2 C
I2 C
I2 C
I2 C
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
16-Lead LFCSP
16-Lead LFCSP
16-Lead LFCSP
16-lead TSSOP
16-lead TSSOP
16-lead TSSOP
16-lead TSSOP
16-Lead LFCSP
16-Lead LFCSP
16-Lead LFCSP
16-lead TSSOP
16-lead TSSOP
16-lead TSSOP
16-lead TSSOP
Evaluation Board
Package
Option
CP-16-22
CP-16-22
CP-16-22
RU-16
RU-16
RU-16
RU-16
CP-16-22
CP-16-22
CP-16-22
RU-16
RU-16
RU-16
RU-16
Branding
DHA
DHG
DN1
DH7
DH4
DMZ
1
Z = RoHS Compliant Part.
The evaluation board is shipped with the 10 kΩ RAB resistor option; however, the board is compatible with both of the available resistor value options.
3
W = Qualified for Automotive Applications.
2
AUTOMOTIVE PRODUCTS
The AD5122AW/AD5142AW models are available with controlled manufacturing to support the quality and reliability requirements of
automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore,
designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for
use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and
to obtain the specific Automotive Reliability reports for these models.
Rev. B | Page 29 of 32
AD5122A/AD5142A
Data Sheet
NOTES
Rev. B | Page 30 of 32
Data Sheet
AD5122A/AD5142A
NOTES
Rev. B | Page 31 of 32
AD5122A/AD5142A
Data Sheet
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
©2012–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10939-0-6/17(B)
Rev. B | Page 32 of 32