AD5252BRUZ100-RL7

Data Sheet AD5251/AD5252 Dual 64-/256-Position I2C Nonvolatile Memory Digital Potentiometers FEATURES ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► FUNCTIONAL BLOCK DIAGRAM AD5251: Dual 64-position resolution AD5252: Dual 256-position resolution AD5251: 50 kΩ AD5252: 1 kΩ, 10 kΩ, 50 kΩ, 100 kΩ Nonvolatile memory stores wiper setting w/write protection Power-on refreshed with EEMEM settings in 300 µs typ EEMEM rewrite time = 540 µs typ Resistance tolerance stored in nonvolatile memory 12 extra bytes in EEMEM for user-defined information I2C compatible serial interface Direct read/write access of RDAC and EEMEM registers Predefined linear increment/decrement commands Predefined ±6 dB step change commands Synchronous or asynchronous dual-channel update Wiper setting readback 4 MHz bandwidth—1 kΩ version Single supply 2.7 V to 5.5 V Dual supply ±2.25 V to ±2.75 V 2 slave address decoding bits allow operation of 4 devices 100-year typical data retention, TA = 55°C Operating temperature: –40°C to +105°C APPLICATIONS ► ► ► ► ► ► ► ► ► Mechanical potentiometer replacement General-purpose DAC replacement LCD panel VCOM adjustment White LED brightness adjustment RF base station power amp bias control Programmable gain and offset control Programmable voltage-to-current conversion Programmable power supply Sensor calibrations Figure 1. GENERAL DESCRIPTION The AD5251/AD52521 are dual-channel, I2C, nonvolatile memory, digitally controlled potentiometers with 64/256 positions, respectively. These devices perform the same electronic adjustment functions as mechanical potentiometers, trimmers, and variable resistors. The parts’ versatile programmability allows multiple modes of operation, including read/write access in the RDAC and EEMEM registers, increment/decrement of resistance, resistance changes in ±6 dB scales, wiper setting readback, and extra EEMEM for storing user-defined information, such as memory data for other components, lookup table, or system identification information. The AD5251/AD5252 allow the host I2C controllers to write any of the 64-/256-step wiper settings in the RDAC registers and store them in the EEMEM. Once the settings are stored, they are restored automatically to the RDAC registers at system power-on; the settings can also be restored dynamically. The AD5251/AD5252 provide additional increment, decrement, +6 dB step change, and –6 dB step change in synchronous or asynchronous channel update mode. The increment and decrement functions allow stepwise linear adjustments, with a ± 6 dB step change equivalent to doubling or halving the RDAC wiper setting. These functions are useful for steep-slope, nonlinear adjustments, such as white LED brightness and audio volume control. The AD5251/AD5252 have a patented resistance-tolerance storing function that allows the user to access the EEMEM and obtain the absolute end-to-end resistance values of the RDACs for precision applications. The AD5251/AD5252 are available in TSSOP-14 packages. AD5251 has only 50 kΩ resistance options and AD5252 is available in 1 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ options. All parts are guaranteed to operate over the –40°C to +105°C extended industrial temperature range. In this data sheet, the nonvolatile memory and EEMEM terms are used interchangeably, as are the digital potentiometer and RDAC terms. 1 Protected by U.S. Patent 7,688,240. Rev. F DOCUMENT FEEDBACK TECHNICAL SUPPORT Information furnished by Analog Devices is believed to be accurate and reliable "as is". However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. Data Sheet AD5251/AD5252 TABLE OF CONTENTS Features................................................................ 1 Applications........................................................... 1 Functional Block Diagram......................................1 General Description...............................................1 Electrical Characteristics....................................... 3 1 kΩ Version.......................................................3 10 kΩ, 50 kΩ, 100 kΩ Versions..........................4 Interface Timing Characteristics.........................6 Absolute Maximum Ratings...................................8 ESD Caution.......................................................8 Pin Configuration and Function Descriptions........ 9 Typical Performance Characteristics................... 10 I2C Interface.........................................................14 I2C Interface General Description.................... 14 I2C Interface Detail Description........................ 15 I2C-Compatible 2-Wire Serial Bus ...................21 Theory of Operation.............................................22 Linear Increment/Decrement Commands........ 22 ±6 dB Adjustments (Doubling/Halving Wiper Setting)........................................................... 22 Digital Input/Output Configuration.................... 22 Multiple Devices on One Bus........................... 23 Terminal Voltage Operation Range.................. 23 Power-Up and Power-Down Sequences..........23 Layout and Power Supply Biasing....................23 Digital Potentiometer Operation....................... 24 Programmable Rheostat Operation..................24 Programmable Potentiometer Operation..........25 Applications Information...................................... 26 LCD Panel VCOM Adjustment........................... 26 Current-Sensing Amplifier................................ 26 Adjustable High Power LED Driver.................. 26 Outline Dimensions............................................. 27 Ordering Guide.................................................27 Evaluation Boards............................................ 27 REVISION HISTORY 1/2022—Rev. E to Rev. F Change to Note 2, Table 3............................................................................................................................... 6 Change to Figure 20 Caption.........................................................................................................................12 Moved Figure 27, Figure 28, Table 6, and Table 7.........................................................................................15 Changes to Table 6........................................................................................................................................ 15 Changes to RDAC/EEMEM Read Section.....................................................................................................17 Changes to Figure 30.................................................................................................................................... 17 Moved Table 9................................................................................................................................................18 Changes to RAB Tolerance Stored in Read-Only Memory Section................................................................ 19 Moved Tabled 10 and Figure 32.................................................................................................................... 19 Changes to I2C-Compatible 2-Wire Serial Bus Section................................................................................. 21 Change to Theory of Operation Section........................................................................................................ 22 Change to Linear Increment/Decrement Commands Section....................................................................... 22 analog.com Rev. F | 2 of 27 Data Sheet AD5251/AD5252 ELECTRICAL CHARACTERISTICS 1 KΩ VERSION VDD = 3 V ± 10% or 5 V ± 10%, VSS = 0 V or VDD/VSS = ±2.5 V ± 10%, VA = VDD, VB = 0 V, –40°C < TA < +105°C, unless otherwise noted. Table 1. Parameter Symbol Conditions DC CHARACTERISTICS— RHEOSTAT MODE Resolution N AD5251 AD5252 RWB, RWA = NC, VDD = 5.5 V, AD5251 RWB, RWA = NC, VDD = 5.5 V, AD5252 RWB, RWA = NC, VDD = 2.7 V, AD5251 RWB, RWA = NC, VDD = 2.7 V, AD5252 RWB, RWA = NC, VDD = 5.5 V, AD5251 RWB, RWA = NC, VDD = 5.5 V, AD5252 RWB, RWA = NC, VDD = 2.7 V, AD5251 RWB, RWA = NC, VDD = 2.7 V, AD5252 TA = 25°C Resistor Differential Nonlinearity2 R-DNL Resistor Nonlinearity2 R-INL Nominal Resistor Tolerance Resistance Temperature Coefficient Wiper Resistance ΔRAB/RAB (ΔRAB/RAB) × 106/ΔT RW Channel-Resistance Matching ΔRAB1/ΔRAB3 DC CHARACTERISTICS—POTENTIOMETER DIVIDER MODE Differential Nonlinearity3 DNL Integral Nonlinearity3 INL Voltage Divider Tempco Full-Scale Error (ΔVW/VW) × 106/ΔT VWFSE Zero-Scale Error VWZSE RESISTOR TERMINALS Voltage Range4 Capacitance5 A, B Capacitance5 W Common-Mode Leakage Current DIGITAL INPUTS AND OUTPUTS Input Logic High Input Logic Low Output Logic High (SDA) Output Logic Low (SDA) WP Leakage Current analog.com VA, VB, VW CA, CB CW ICM VIH VIL VOH VOL IWP Min –0.5 –1.00 –0.75 –1.5 –0.5 –2.0 –1.0 –2 –30 ±0.2 ±0.25 ±0.30 ±0.3 ±0.2 ±0.5 +2.5 +9 650 75 200 0.15 IW = 1 V/R, VDD = 5 V IW = 1 V/R, VDD = 3 V AD5251 AD5252 AD5251 AD5252 Code = half scale Code = full scale, VDD = 5.5 V, AD5251 Code = full scale, VDD = 5.5 V, AD5252 Code = full scale, VDD = 2.7 V, AD5251 Code = full scale, VDD = 2.7 V, AD5252 Code = zero scale, VDD = 5.5 V, AD5251 Code = zero scale, VDD = 5.5 V, AD5252 Code = zero scale, VDD = 2.7 V, AD5251 Code = zero scale, VDD = 2.7 V, AD5252 Typ1 –0.5 –1.00 –0.5 –2.0 –5 –16 −6 –23 0 0 0 0 ±0.1 ±0.25 ±0.2 ±0.5 25 –3 –11 –4 –16 3 11 4 15 VSS f = 1 kHz, measured to GND, code = half scale f = 1 kHz, measured to GND, code = half scale VA = VB = VDD/2 VDD = 5 V, VSS = 0 V VDD/VSS = 2.7 V/0 V or VDD/VSS = ± 2.5 V VDD = 5 V, VSS = 0 V RPULL-UP = 2.2 kΩ to VDD = 5 V, VSS = 0 V RPULL-UP = 2.2 kΩ to VDD = 5 V, VSS = 0 V WP = VDD Max Unit 6 8 +0.5 +1.00 +0.75 +1.5 +0.5 +2.0 +4.0 +14 +30 Bits Bits LSB LSB LSB LSB LSB LSB LSB LSB % ppm/°C Ω Ω % 130 300 +0.5 +1.00 +0.5 +2.0 0 0 0 0 5 16 6 20 VDD LSB LSB LSB LSB ppm/°C LSB LSB LSB LSB LSB LSB LSB LSB 85 V pF 95 pF 0.01 1 2.4 2.1 0.8 4.9 0.4 8 µA V V V V V µA Rev. F | 3 of 27 Data Sheet AD5251/AD5252 ELECTRICAL CHARACTERISTICS Table 1. Parameter Symbol Conditions A0 Leakage Current Input Leakage Current (Other than WP and A0) Input Capacitance5 POWER SUPPLIES Single-Supply Power Range Dual-Supply Power Range Positive Supply Current Negative Supply Current IA0 II A0 = GND VIN = 0 V or VDD EEMEM Data Storing Mode Current EEMEM Data Restoring Mode Current6 Power Dissipation7 Power Supply Sensitivity CI VDD VDD/VSS IDD ISS IDD_STORE IDD_RESTORE PDISS PSS DYNAMIC CHARACTERISTICS5, 8 Bandwidth –3 dB Total Harmonic Distortion VW Settling Time Resistor Noise Voltage Min BW THD tS eN_WB Digital Crosstalk CT Analog Coupling CAT Typ1 Max Unit 3 ±1 µA µA 5 VSS = 0 V 2.7 ±2.25 VIH = VDD or VIL = GND VIH = VDD or VIL = GND, VDD = 2.5 V, VSS = –2.5 V VIH = VDD or VIL = GND VIH = VDD or VIL = GND VIH = VDD = 5 V or VIL = GND ΔVDD = 5 V ± 10% ΔVDD = 3 V ± 10% 5 –5 pF 5.5 ±2.75 15 –15 V V µA µA 0.075 +0.025 +0.04 mA mA mW %/% %/% 35 2.5 −0.025 –0.04 RAB = 1 kΩ VA = 1 V rms, VB = 0 V, f = 1 kHz VA = VDD, VB = 0 V RWB = 500 Ω, f = 1 kHz (thermal noise only) VA = VDD, VB = 0 V, measure VW with adjacent RDAC making full-scale change Signal input at A1 and measure the output at W3, f = 1 kHz +0.010 +0.02 4 0.05 0.2 3 MHz % µs nV/√Hz –80 dB –72 dB 1 Typical values represent average readings at 25°C and VDD = 5 V. 2 Resistor position nonlinearity error (R-INL) is the deviation from an ideal value measured between the maximum and minimum resistance wiper positions. R-DNL is the relative step change from an ideal value measured between successive tap positions. Parts are guaranteed monotonic, except R-DNL of AD5252 1 kΩ version at VDD = 2.7 V, IW = VDD/R for both VDD = 3 V and VDD = 5 V. 3 INL and DNL are measured at VW with the RDAC configured as a potentiometer divider, similar to a voltage output digital-to-analog converter. VA = VDD and VB = 0 V. DNL specification limits of ±1 LSB maximum are guaranteed monotonic operating conditions. 4 Resistor Terminal A, Terminal B, and Terminal W have no limitations on polarity with respect to each other. 5 Guaranteed by design and not subject to production test. 6 Command 0 NOP should be activated after Command 1 to minimize IDD_READ current consumption. 7 PDISS is calculated from IDD × VDD = 5 V. 8 All dynamic characteristics use VDD = 5 V. 10 KΩ, 50 KΩ, 100 KΩ VERSIONS VDD = +3 V ± 10% or +5 V ± 10%, VSS = 0 V or VDD/VSS = ± 2.5 V ± 10%, VA = VDD, VB = 0 V, –40°C < TA < +105°C, unless otherwise noted. Table 2. Parameter Symbol Conditions DC CHARACTERISTICS— RHEOSTAT MODE Resolution N AD5251 AD5252 RWB, RWA = NC, AD5251 RWB, RWA = NC, AD5252 Resistor Differential Nonlinearity2 analog.com R-DNL Min −0.75 −1.00 Typ1 Max Unit ±0.10 ±0.25 6 8 +0.75 +1.00 Bits Bits LSB LSB Rev. F | 4 of 27 Data Sheet AD5251/AD5252 ELECTRICAL CHARACTERISTICS Table 2. Symbol Conditions Min Typ1 Max Unit Resistor Nonlinearity2 R-INL ΔRAB/RAB (ΔRAB/RAB) × 106/ΔT RW −0.75 −2.5 −20 ±0.25 ±1.0 Nominal Resistor Tolerance Resistance Temperature Coefficient Wiper Resistance RWB, RWA = NC, AD5251 RWB, RWA = NC, AD5252 TA = 25°C +0.75 +2.5 +20 Channel-Resistance Matching ΔRAB1/ΔRAB2 LSB LSB % ppm/°C Ω Ω % % Parameter DC CHARACTERISTICS— POTENTIOMETER DIVIDER MODE Differential Nonlinearity3 DNL Integral Nonlinearity3 INL Voltage Divider Temperature Coefficient Full-Scale Error (ΔVW/VW) × 106/ΔT Zero-Scale Error VWZSE RESISTOR TERMINALS Voltage Range4 Capacitance5 A, B Capacitance5 W Common-Mode Leakage Current DIGITAL INPUTS AND OUTPUTS Input Logic High Input Logic Low Output Logic High (SDA) Output Logic Low (SDA) WP Leakage Current A0 Leakage Current Input Leakage Current (Other than WP and A0) Input Capacitance5 POWER SUPPLIES Single-Supply Power Range Dual-Supply Power Range Positive Supply Current Negative Supply Current EEMEM Data Storing Mode Current EEMEM Data Restoring Mode Current6 Power Dissipation7 analog.com VWFSE VA, VB, VW CA, CB CW ICM VIH VIL VOH VOL IWP IA0 II 650 75 200 0.15 0.05 IW = 1 V/R, VDD = 5 V IW = 1 V/R, VDD = 3 V RAB = 10 kΩ, 50 kΩ RAB = 100 kΩ AD5251 AD5252 AD5251 AD5252 Code = half scale −0.5 −1.0 −0.50 −1.5 ±0.1 ±0.3 ±0.15 ±0.5 15 +0.5 +1.0 +0.50 +1.5 LSB LSB LSB LSB ppm/°C Code = full scale, AD5251 Code = full scale, AD5252 Code = zero scale, AD5251 Code = zero scale, AD5252 −1.0 −3 0 0 −0.3 −1 0.3 1.2 0 0 1.0 3.0 LSB LSB LSB LSB VDD 85 V pF 95 pF VSS f = 1 kHz, measured to GND, code = half scale f = 1 kHz, measured to GND, code = half scale VA = VB = VDD/2 VDD = 5 V, VSS = 0 V VDD/VSS = +2.7 V/0 V or VDD/VSS = ±2.5 V VDD = 5 V, VSS = 0 V VDD/VSS = +2.7 V/0 V or VDD/VSS = ±2.5 V RPULL-UP = 2.2 kΩ to VDD = 5 V, VSS = 0 V RPULL-UP = 2.2 kΩ to VDD = 5 V, VSS = 0 V WP = VDD A0 = GND VIN = 0 V or VDD 0.01 1.00 µA 2.4 2.1 V V V V V V µA µA µA 0.8 0.6 4.9 0.4 8 3 ±1 CI VDD VDD/VSS IDD ISS 130 300 5 VSS = 0 V IDD_STORE IDD_RESTORE VIH = VDD or VIL = GND VIH = VDD or VIL = GND, VDD = 2.5 V, VSS = −2.5 V VIH = VDD or VIL = GND, TA = 0°C to 105°C VIH = VDD or VIL = GND, TA = 0°C to 105°C PDISS VIH = VDD = 5 V or VIL = GND 2.7 ±2.25 5 −5 pF 5.5 ±2.75 15 −15 35 2.5 V V µA µA mA mA 0.075 mW Rev. F | 5 of 27 Data Sheet AD5251/AD5252 ELECTRICAL CHARACTERISTICS Table 2. Parameter Power Supply Sensitivity DYNAMIC CHARACTERISTICS5, 8 –3 dB Bandwidth Symbol Conditions Min Typ1 Max Unit PSS ΔVDD = 5 V ± 10% ΔVDD = 3 V ± 10% −0.005 −0.010 +0.002 +0.002 +0.005 +0.010 %/% %/% BW RAB = 10 kΩ RAB = 50 kΩ RAB = 100 kΩ VA = 1 V rms, VB = 0 V, f = 1 kHz VA = VDD, VB = 0 V, RAB = 10 kΩ VA = VDD, VB = 0 V, RAB = 50 kΩ VA = VDD, VB = 0 V, RAB = 100 kΩ RAB = 10 kΩ, code = midscale, f = 1 kHz (thermal noise only) RAB = 50 kΩ, code = midscale, f = 1 kHz (thermal noise only) RAB = 100 kΩ, code = midscale, f = 1 kHz (thermal noise only) VA = VDD, VB = 0 V, measure VW with adjacent RDAC making full-scale change Signal input at A1 and measure output at W3, f = 1 kHz Total Harmonic Distortion VW Settling Time THDW tS Resistor Noise Voltage eN_WB Digital Crosstalk CT Analog Coupling CAT 400 80 40 0.05 1.5 7 14 9 kHz kHz kHz % µs µs µs nV/√Hz 20 nV/√Hz 29 nV/√Hz −80 dB −72 dB 1 Typical values represent average readings at 25°C and VDD = 5 V. 2 Resistor position nonlinearity error (R-INL) is the deviation from an ideal value measured between the maximum and minimum resistance wiper positions. R-DNL is the relative step change from an ideal value measured between successive tap positions. Parts are guaranteed monotonic, except R-DNL of AD5252 1 kΩ version at VDD = 2.7 V, IW = VDD/R for both VDD = 3 V and VDD = 5 V. 3 INL and DNL are measured at VW with the RDAC configured as a potentiometer divider, similar to a voltage output DAC. VA = VDD and VB = 0 V. DNL specification limits of ±1 LSB maximum are guaranteed monotonic operating conditions. 4 Resistor Terminal A, Terminal B, and Terminal W have no limitations on polarity with respect to each other. 5 Guaranteed by design and not subject to production test. 6 Command 0 NOP should be activated after Command 1 to minimize IDD_READ current consumption. 7 PDISS is calculated from IDD × VDD = 5 V. 8 All dynamic characteristics use VDD = 5 V. INTERFACE TIMING CHARACTERISTICS All input control voltages are specified with tR = tF = 2.5 ns (10% to 90% of 3 V) and timed from a voltage level of 1.5 V. Switching characteristics are measured using both VDD = 3 V and 5 V. Table 3. Interface Timing and EEMEM Reliability Characteristics (All Parts)1 Parameter Symbol INTERFACE TIMING SCL Clock Frequency tBUF Bus-Free Time Between Stop and Start tHD;STA Hold Time (Repeated Start) fSCL t1 t2 tLOW Low Period of SCL Clock tHIGH High Period of SCL Clock tSU;STA Set-up Time for Start Condition tHD;DAT Data Hold Time tSU;DAT Data Set-up Time analog.com t3 t4 t5 t6 t7 Conditions After this period, the first clock pulse is generated. Min Typ Max Unit 400 1.3 0.6 kHz µs µs 1.3 0.6 0.6 0 100 µs µs µs µs ns 0.9 Rev. F | 6 of 27 Data Sheet AD5251/AD5252 ELECTRICAL CHARACTERISTICS Table 3. Interface Timing and EEMEM Reliability Characteristics (All Parts)1 Parameter tF Fall Time of Both SDA and SCL Signals tR Rise Time of Both SDA and SCL Signals tSU;STO Set-up Time for Stop Condition EEMEM Data Storing Time EEMEM Data Restoring Time at Power-On2 EEMEM Data Restoring Time upon Restore Command or Reset Operation2 EEMEM Data Rewritable Time (Delay Time After PowerOn or Reset Before EEMEM Can Be Written) FLASH/EE MEMORY RELIABILITY Endurance3 Data Retention4 Symbol t8 t9 t10 tEEMEM_STORE tEEMEM_RESTORE1 tEEMEM_RESTORE2 Conditions Min Typ Max Unit 300 300 26 300 ns ns µs ms µs 300 µs 540 µs 100 k cycles Years 0.6 VDD rise time dependent. Measure without decoupling capacitors at VDD and VSS. VDD = 5 V. tEEMEM_REWRITE 100 1 Guaranteed by design; not subject to production test. See Figure 23 for location of measured values. 2 During power-up, all outputs are preset to midscale before restoring the EEMEM contents. RDAC1 has the shortest EEMEM data restoring time, whereas RDAC3 has the longest. 3 Endurance is qualified to 100,000 cycles per JEDEC Standard 22, Method A117, and measured at −40°C, +25°C, and +105°C; typical endurance at +25°C is 700,000 cycles. 4 Retention lifetime equivalent at junction temperature TJ = 55°C per JEDEC Std. 22, Method A117. Retention lifetime based on an activation energy of 0.6 eV derates with junction temperature in Flash/EE memory. analog.com Rev. F | 7 of 27 Data Sheet AD5251/AD5252 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 4. Parameter Rating VDD to GND VSS to GND VDD to VSS VA, VB, VW to GND Maximum Current IWB, IWA Pulsed IWB Continuous (RWB ≤ 1 kΩ, A Open)1 IWA Continuous (RWA ≤ 1 kΩ, B Open)1 IAB Continuous1 RAB = 1 kΩ RAB = 10 kΩ RAB = 50 kΩ RAB = 100 kΩ Digital Inputs and Output Voltage to GND Operating Temperature Range Maximum Junction Temperature (TJMAX) Storage Temperature Range Lead Temperature (Soldering, 10 sec) Vapor Phase (60 sec) Infrared (15 sec) TSSOP-14 Thermal Resistance2 θJA −0.3 V, +7 V +0.3 V, −7 V 7V VSS, VDD ±20 mA ±5 mA ±5 mA ±5 mA ±500 µA ±100 µA ±50 µA 0 V, 7 V −40°C to +105°C 150°C −65°C to +150°C 300°C 215°C 220°C 136°C/W 1 Maximum terminal current is bound by the maximum applied voltage across any two of the A, B, and W terminals at a given resistance, the maximum current handling of the switches, and the maximum power dissipation of the package. VDD = 5 V. 2 Package power dissipation = (TJMAX − TA)/θJA. analog.com Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Rev. F | 8 of 27 Data Sheet AD5251/AD5252 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 2. Pin Configuration Table 5. Pin Function Descriptions Pin No. Mnemonic Description 1 VDD 2 3 4 5 6 7 AD0 WP W1 B1 A1 SDA 8 VSS 9 SCL 10 11 12 13 14 DGND AD1 A3 B3 W3 Positive Power Supply Pin. Connect +2.7 V to +5 V for single supply or ±2.7 V for dual supply, where VDD – VSS ≤ 5.5 V. VDD must be able to source 35 mA for 26 ms when storing data to EEMEM. I2C Device Address 0. AD0 and AD1 allow four AD5251/AD5252 devices to be addressed. Write Protect, Active Low. VWP ≤ VDD + 0.3 V. Wiper Terminal of RDAC1. VSS ≤ VW1 ≤ VDD.1 B Terminal of RDAC1. VSS ≤ VB1 ≤ VDD.1 A Terminal of RDAC1. VSS ≤ VA1 ≤ VDD.1 Serial Data Input/Output Pin. Shifts in one bit at a time upon positive clock edges. MSB loaded first. Open-drain MOSFET requires pull-up resistor. Negative Supply. Connect to 0 V for single supply or –2.7 V for dual supply, where VDD – VSS ≤ +5.5 V. If VSS is used in dual supply, VSS must be able to sink 35 mA for 26 ms when storing data to EEMEM. Serial Input Register Clock Pin. Shifts in one bit at a time upon positive clock edges. VSCL ≤ (VDD + 0.3 V). Pull-up resistor is recommended for SCL to ensure minimum power. Digital Ground. Connect to system analog ground at a single point. I2C Device Address 1. AD0 and AD1 allow four AD5251/AD5252 devices to be addressed. A Terminal of RDAC3. VSS ≤ VA3 ≤ VDD.1 B Terminal of RDAC3. VSS ≤ VB3 ≤ VDD.1 Wiper Terminal of RDAC3. VSS ≤ VW3 ≤ VDD.1 1 For quad-channel device software compatibility, the dual potentiometers in the parts are designated as RDAC1 and RDAC3. analog.com Rev. F | 9 of 27 Data Sheet AD5251/AD5252 TYPICAL PERFORMANCE CHARACTERISTICS analog.com Figure 3. R-INL vs. Code Figure 6. DNL vs. Code Figure 4. R-DNL vs. Code Figure 7. Supply Current vs. Temperature Figure 5. INL vs. Code Figure 8. Supply Current vs. Digital Input Voltage, TA = 25°C Rev. F | 10 of 27 Data Sheet AD5251/AD5252 TYPICAL PERFORMANCE CHARACTERISTICS Figure 9. Wiper Resistance vs. VBIAS Figure 12. AD5252 Potentiometer Mode Tempco ∆VWB/∆T vs. Code Figure 10. Change of RWB vs. Temperature Figure 13. AD5252 Gain vs. Frequency vs. Code, RAB = 1 kΩ, TA = 25°C Figure 11. AD5252 Rheostat Mode Tempco ∆RWB/∆T vs. Code Figure 14. AD5252 Gain vs. Frequency vs. Code, RAB = 10 kΩ, TA = 25°C analog.com Rev. F | 11 of 27 Data Sheet AD5251/AD5252 TYPICAL PERFORMANCE CHARACTERISTICS Figure 15. AD5252 Gain vs. Frequency vs. Code, RAB = 50 kΩ, TA = 25°C Figure 16. AD5252 Gain vs. Frequency vs. Code, RAB = 100 kΩ, TA = 25°C Figure 18. Supply Current vs. Digital Input Clock Frequency Figure 19. Clock Feedthrough and Midscale Transition Glitch Figure 20. tEEMEM_RESTORE of RDAC1 and RDAC3 Figure 17. AD5252 ΔRAB vs. Code, TA = 25°C analog.com Rev. F | 12 of 27 Data Sheet AD5251/AD5252 TYPICAL PERFORMANCE CHARACTERISTICS Figure 21. AD5251 IWB_MAX vs. Code analog.com Figure 22. AD5252 IWB_MAX vs. Code Rev. F | 13 of 27 Data Sheet AD5251/AD5252 I2C INTERFACE Figure 23. I2C Interface Timing Diagram I2C INTERFACE GENERAL DESCRIPTION Figure 24. I2C—Master Writing Data to Slave Figure 25. I2C—Master Reading Data from Slave Figure 26. I2C—Combined Write/Read analog.com Rev. F | 14 of 27 Data Sheet AD5251/AD5252 I2C INTERFACE I2C INTERFACE DETAIL DESCRIPTION location, which provides nonvolatile wiper storage functionality. The addresses are shown in Table 7. The single and consecutive write operations also apply to EEMEM write operations. RDAC/EEMEM Write Setting the wiper position requires an RDAC write operation. The single write operation is shown in Figure 27, and the consecutive write operation is shown in Figure 28. In the consecutive write operation, if the RDAC is selected and the address starts at 00001, the first data byte goes to RDAC1 and the second data byte goes to RDAC3. The RDAC address is shown in Table 6. While the RDAC wiper setting is controlled by a specific RDAC register, each RDAC register corresponds to a specific EEMEM There are 12 nonvolatile memory locations: EEMEM4 to EEMEM15. Users can store a total of 12 bytes of information, such as memory data for other components, look-up tables, or system identification information. In a write operation to the EEMEM registers, the device disables the I2C interface during the internal write cycle. Acknowledge polling is required to determine the completion of the write cycle. See the EEMEM Write-Acknowledge Polling section. Figure 27. Single Write Mode Figure 28. Consecutive Write Mode Table 6. Addresses for Writing Data Byte Contents to RDAC Registers (R/W = 0, CMD/REG = 0, EE/RDAC = 0) A4 A3 A2 A1 A0 RDAC 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 0 0 0 0 1 : : 1 0 0 1 1 0 : : 1 0 1 0 1 0 : : 1 Reserved RDAC1 Reserved RDAC3 Reserved : : Reserved 1 Data Byte Description 6-/8-bit wiper setting1 6-/8-bit wiper setting1 The two most significant data bits of AD5251 are X. X is don't care. Table 7. Addresses for Writing (Storing) RDAC Settings and User-Defined Data to EEMEM Registers (R/W = 0, CMD/REG = 0, EE/RDAC = 1) A4 A3 A2 A1 A0 Data Byte Description 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 1 0 0 1 0 1 0 Reserved Store RDAC1 setting to EEMEM11 Reserved Store RDAC3 setting to EEMEM31 Store user data to EEMEM4 analog.com Rev. F | 15 of 27 Data Sheet AD5251/AD5252 I2C INTERFACE Table 7. Addresses for Writing (Storing) RDAC Settings and User-Defined Data to EEMEM Registers (R/W = 0, CMD/REG = 0, EE/RDAC = 1) A4 A3 A2 A1 A0 Data Byte Description 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 1 1 0 0 1 1 0 0 1 1 1 0 1 0 1 0 1 0 1 0 1 Store user data to EEMEM5 Store user data to EEMEM6 Store user data to EEMEM7 Store user data to EEMEM8 Store user data to EEMEM9 Store user data to EEMEM10 Store user data to EEMEM11 Store user data to EEMEM12 Store user data to EEMEM13 Store user data to EEMEM14 Store user data to EEMEM15 1 Users can store any of the 64 RDAC settings directly to the EEMEM for AD5251, or any of the 256 RDAC settings directly to the EEMEM for the AD5252. This is not limited to current RDAC wiper setting. analog.com Rev. F | 16 of 27 Data Sheet AD5251/AD5252 I2C INTERFACE RDAC/EEMEM Read The AD5251/AD5252 provide two different RDAC or EEMEM read operations. For example, Figure 29 shows the method of reading the RDAC1 and RDAC3 contents without specifying the address, assuming Address RDAC1 was already selected in the previous operation. If Address N other than RDAC1 was previously selected, readback starts with Address N, followed by N + 1, and so on. Figure 30 illustrates a random RDAC or EEMEM read operation. This operation allows users to specify which RDAC or EEMEM register is read by issuing a dummy write command to change the RDAC address pointer and then proceeding with the RDAC read operation at the new address location. Table 8. Addresses for Reading (Restoring) RDAC Settings and User Data from EEMEM (R/W = 1, CMD/REG = 0, EE/RDAC = 1) A4 A3 A2 A1 A0 Data Byte Description 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Reserved Read RDAC1 setting from EEMEM1 Reserved Read RDAC3 setting from EEMEM3 Read user data from EEMEM4 Read user data from EEMEM5 Read user data from EEMEM6 Read user data from EEMEM7 Read user data from EEMEM8 Read user data from EEMEM9 Read user data from EEMEM10 Read user data from EEMEM11 Read user data from EEMEM12 Read user data from EEMEM13 Read user data from EEMEM14 Read user data from EEMEM15 Figure 29. RDAC Current Read (Restricted to Previously Selected Address Stored in the Register) Figure 30. RDAC or EEMEM Random Read Figure 31. RDAC Quick Command Write (Dummy Write) analog.com Rev. F | 17 of 27 Data Sheet AD5251/AD5252 I2C INTERFACE RDAC/EEMEM Quick Commands The AD5251/AD5252 feature 12 quick commands that facilitate easy manipulation of RDAC wiper settings and provide RDAC-toEEMEM storing and restoring functions. The command format is shown in Figure 31, and the command descriptions are shown in Table 9. When using a quick command, issuing a third byte is not needed, but is allowed. The quick commands reset and store RDAC to EEMEM require acknowledge polling to determine whether the command has finished executing. Table 9. RDAC-to-EEMEM Interface and RDAC Operation Quick Command Bits (CMD/REG = 1, A2 = 0) C3 C2 C1 C0 Command Description 0 0 0 0 NOP 0 0 0 1 Restore EEMEM (A1, A0) to RDAC (A1, A0)1 0 0 1 0 Store RDAC (A1, A0) to EEMEM (A1, A0) 0 0 1 1 Decrement RDAC (A1, A0) 6 dB 0 1 0 0 Decrement all RDACs 6 dB 0 1 0 1 Decrement RDAC (A1, A0) one step 0 1 1 0 Decrement all RDACs one step 0 1 1 1 Reset: restore EEMEMs to all RDACs 1 0 0 0 Increment RDACs (A1, A0) 6 dB 1 0 0 1 Increment all RDACs 6 dB 1 0 1 0 Increment RDACs (A1, A0) one step 1 0 1 1 Increment all RDACs one step 1 1 0 0 Reserved : : : : : : : : : : 1 1 1 1 Reserved 1 This command leaves the device in the EEMEM read power state, which consumes power. Issue the NOP command to return the device to its idle state. analog.com Rev. F | 18 of 27 Data Sheet AD5251/AD5252 I2C INTERFACE RAB Tolerance Stored in Read-Only Memory The AD5251/AD5252 feature patented RAB tolerances storage in the nonvolatile memory. The tolerance of each channel is stored in the memory during the factory production and can be read by users at any time. The knowledge of the stored tolerance, which is the average of RAB over all codes (see Figure 16), allows users to predict RAB accurately. This feature is valuable for precision, rheostat mode, and open-loop applications in which knowledge of absolute resistance is critical. The stored tolerances reside in the read-only memory and are expressed as percentages. Each tolerance is stored in two memory locations (see Table 10). The tolerance data is expressed in sign magnitude binary format stored in two bytes; an example is shown in Figure 32. For the first byte in Register N, the MSB is designated for the sign (0 = + and 1 = –) and the remaining seven LSBs are designated for the integer portion of the tolerance. For the second byte in Register N + 1, all eight data bits are designated for the decimal portion of tolerance. As shown in Table 10 and Figure 32, for example, if the rated RAB is 10 kΩ and the data readback from Address 11000 shows 0001 1100 and Address 11001 shows 0000 1111, then RDAC1 tolerance can be calculated as MSB (from Address 11000): 0 = + Next 7 LSBs (from Address 11000): 001 1100 = 28 8 LSBs (from Address 11001): 0000 1111 = 15 × 2–8 = 0.06 Tolerance = 28.06% and, therefore, RAB_ACTUAL = 12.806 kΩ Table 10. Address Table for Reading Tolerance (CMD/REG = 0, EE/RDAC = 1, A4 = 1) A4 A3 A2 A1 A0 Data Byte Description 0 0 0 0 0 Reserved : : : : : : : : : : : : 1 1 0 0 1 Reserved 1 1 0 1 0 Sign and 7-bit integer values of RDAC1 tolerance (read only) 1 1 0 1 1 8-bit decimal value of RDAC1 tolerance (read only) 1 1 1 0 0 Reserved 1 1 1 0 1 Reserved 1 1 1 1 0 Sign and 7-bit integer values of RDAC3 tolerance (read only) 1 1 1 1 1 8-bit decimal value of RDAC3 tolerance (read only) Figure 32. Format of Stored Tolerance in Sign Magnitude Format with Bit Position Descriptions (Unit Is %, Only Data Bytes Are Shown) analog.com Rev. F | 19 of 27 Data Sheet AD5251/AD5252 I2C INTERFACE EEMEM Write-Acknowledge Polling After each write operation to the EEMEM registers, an internal write cycle begins. The I2C interface of the device is disabled. To determine if the internal write cycle is complete and the I2C interface is enabled, interface polling can be executed. I2C interface polling can be conducted by sending a start condition, followed by the slave address and the write bit. If the I2C interface responds with an ACK, the write cycle is complete and the interface is ready to proceed with further operations. Otherwise, I2C interface polling can be repeated until it succeeds. Command 2 and Command 7 also require acknowledge polling. EEMEM Write Protection Setting the WP pin to logic low after EEMEM programming protects the memory and RDAC registers from future write operations. In this mode, the EEMEM and RDAC read operations function as normal. analog.com Rev. F | 20 of 27 Data Sheet AD5251/AD5252 I2C INTERFACE I2C-COMPATIBLE 2-WIRE SERIAL BUS Figure 33. General I2C Write Pattern Figure 34. General I2C Read Pattern The first byte of the AD5251/AD5252 is a slave address byte (see Figure 33 and Figure 34). It has a 7-bit slave address and an R/W bit. The 5 MSB of the slave address is 01011, and the next 2 LSB is determined by the states of the AD1 and AD0 pins. AD1 and AD0 allow the user to place up to four AD5251/AD5252 devices on one bus. AD5251/AD5252 can be controlled via an I2C-compatible serial bus and are connected to this bus as slave devices. The 2-wire I2C serial bus protocol (see Figure 33 and Figure 34) follows: 1. The master initiates a data transfer by establishing a start condition, such that SDA goes from high to low while SCL is high (see Figure 33). The following byte is the slave address byte, which consists of the 5 MSB of a slave address defined as 01011. The next two bits are AD1 and AD0, I2C device address bits. Depending on the states of their AD1 and AD0 bits, four AD5251/AD5252 devices can be addressed on the same bus. The last LSB, the R/W bit, determines whether data is read from or written to the slave device. The slave whose address corresponds to the transmitted address responds by pulling the SDA line low during the ninth clock pulse (this is called an acknowledge bit). At this stage, all other devices on the bus remain idle while the selected device waits for data to be written to or read from its serial register. 2. In the write mode (except when restoring EEMEM to the RDAC register), there is an instruction byte that follows the slave address byte. The MSB of the instruction byte is labeled CMD/ REG. MSB = 1 enables CMD, the command instruction byte; MSB = 0 enables general register writing. The third MSB in the instruction byte, labeled EE/RDAC, is true when MSB = 0 or when the device is in general writing mode. EE enables the EEMEM register, and REG enables the RDAC register. The 5 LSB, A4 to A0, designates the addresses of the EEMEM and analog.com RDAC registers (see Figure 27 and Figure 28). When MSB = 1 or when the device is in CMD mode, the four bits following the MSB are C3 to C1, which correspond to 12 predefined EEMEM controls and quick commands; there are also four factory-reserved commands. The 3 LSB—A2, A1, and A0—are addresses, but only 001 and 011 are used for RDAC1 and RDAC3, respectively (see Figure 31). After acknowledging the instruction byte, the last byte in the write mode is the data byte. Data is transmitted over the serial bus in sequences of nine clock pulses (eight data bits followed by an acknowledge bit). The transitions on the SDA line must occur during the low period of SCL and remain stable during the high period of SCL (see Figure 33). 3. In current read mode, the RDAC1 data byte immediately follows the acknowledgment of the slave address byte. After an acknowledgment, a dummy read follows, then RDAC3, and so on. (There is a slight difference in write mode, where the last eight data bits representing RDAC3 data are followed by a no acknowledge bit.) Similarly, the transitions on the SDA line must occur during the low period of SCL and remain stable during the high period of SCL (see Figure 34). Another reading method, random read method, is shown in Figure 30. 4. When all data bits have been read or written, a stop condition is established by the master. A stop condition is defined as a low-to-high transition on the SDA line that occurs while SCL is high. In write mode, the master pulls the SDA line high during the 10th clock pulse to establish a stop condition (see Figure 33). In read mode, the master issues a no acknowledge for the ninth clock pulse, that is, the SDA line remains high. The master brings the SDA line low before the 10th clock pulse and then brings the SDA line high to establish a stop condition (see Figure 34). Rev. F | 21 of 27 Data Sheet AD5251/AD5252 THEORY OF OPERATION The AD5251/AD5252 are dual-channel digital potentiometers that allow 64/256 linear resistance step adjustments. The AD5251/ AD5252 employ double-gate CMOS EEPROM technology, which allows resistance settings and user-defined data to be stored in the EEMEM registers. The EEMEM is nonvolatile, such that settings remain when power is removed. The RDAC wiper settings are restored from the nonvolatile memory settings during device powerup and can also be restored at any time during operation. The AD5251/AD5252 resistor wiper positions are determined by the RDAC register contents. The RDAC register acts like a scratch-pad register, allowing unlimited changes of resistance settings. RDAC register contents can be changed using the device’s serial I2C interface. The format of the data-words and the commands to program the RDAC registers are discussed in the I2C Interface Detail Description section. The two RDAC registers have corresponding EEMEM memory locations that provide nonvolatile storage of resistor wiper position settings. The AD5251/AD5252 provide commands to store the RDAC register contents to their respective EEMEM memory locations. During subsequent power-on sequences, the RDAC registers are automatically loaded with the stored value. Whenever the EEMEM write operation is enabled, the device activates the internal charge pump and raises the EEMEM cell gate bias voltage to a high level; this essentially erases the current content in the EEMEM register and allows subsequent storage of the new content. Saving data to an EEMEM register consumes about 35 mA of current and lasts approximately 26 ms. Because of charge-pump operation, all RDAC channels may experience noise coupling during the EEMEM writing operation. The EEMEM restore time in power-up or during operation is about 300 µs. Note that the power-up EEMEM refresh time depends on how fast VDD reaches its final value. As a result, any supply voltage decoupling capacitors limit the EEMEM restore time during power-up. For example, Figure 20 shows a power-up profile of the VDD where there is no decoupling capacitor and the applied power is a digital signal. The device initially resets the measured RDACs to midscale before restoring the EEMEM contents. By default, EEMEM is loaded at midscale until a new value is loaded. The omission of the decoupling capacitors should only be considered when the fast restoring time is absolutely needed in the application. In addition, users should issue a NOP Command 0 immediately after using Command 1 to restore the EEMEM setting to RDAC, thereby minimizing supply current dissipation. Reading user data directly from EEMEM does not require a similar NOP command execution. In addition to the movement of data between RDAC and EEMEM registers, the AD5251/AD5252 provide other shortcut commands that facilitate programming, as shown in Table 11. analog.com Table 11. Quick Commands Command Description 0 1 NOP. Restore EEMEM content to RDAC. Users should issue NOP immediately after this command to conserve power. Store RDAC register setting to EEMEM. Decrement RDAC 6 dB (shift data bits right). Decrement all RDACs 6 dB (shift all data bits right). Decrement RDAC one step. Decrement all RDACs one step. Reset EEMEM contents to all RDACs. Increment RDAC 6 dB (shift data bits left). Increment all RDACs 6 dB (shift all data bits left). Increment RDAC one step. Increment all RDACs one step. Reserved. 2 3 4 5 6 7 8 9 10 11 12 to 15 LINEAR INCREMENT/DECREMENT COMMANDS The increment and decrement commands (10, 11, 5, and 6) are useful for linear step adjustment applications. These commands simplify microcontroller software coding by allowing the controller to send just an increment or decrement command to the AD5251/ AD5252. The adjustments can be directed to a single RDAC or to all RDACs. ±6 DB ADJUSTMENTS (DOUBLING/HALVING WIPER SETTING) The AD5251/AD5252 accommodate ±6 dB adjustments of the RDAC wiper positions by shifting the register contents to left/right for increment/decrement operations, respectively. Command 3, Command 4, Command 8, and Command 9 can be used to increment or decrement the wiper positions in 6 dB steps synchronously or asynchronously. Incrementing the wiper position by +6 dB essentially doubles the RDAC register value, whereas decrementing the wiper position by –6 dB halves the register content. Internally, the AD5251/AD5252 use shift registers to shift the bits left and right to achieve a ±6 dB increment or decrement. The maximum number of adjustments is nine and eight steps for incrementing from zero scale and decrementing from full scale, respectively. These functions are useful for various audio/video level adjustments, especially for white LED brightness settings in which human visual responses are more sensitive to large adjustments than to small adjustments. DIGITAL INPUT/OUTPUT CONFIGURATION SDA is a digital input/output with an open-drain MOSFET that requires a pull-up resistor for proper communication. On the other hand, SCL and WP are digital inputs for which pull-up resistors are recommended to minimize the MOSFET cross-conduction current when the driving signals are lower than VDD. Rev. F | 22 of 27 Data Sheet AD5251/AD5252 THEORY OF OPERATION SCL and WP have ESD protection diodes, as shown in Figure 35 and Figure 36. WP can be permanently tied to VDD without a pull-up resistor if the write-protect feature is not used. If WP is left floating, an internal current source pulls it low to enable write protection. In applications in which the device is programmed infrequently, this allows the part to default to write-protection mode after any one-time factory programming or field calibration without using an on-board pull-down resistor. Because there are protection diodes on all inputs, the signal levels must not be greater than VDD to prevent forward biasing of the diodes. Figure 35. SCL Digital Input TERMINAL VOLTAGE OPERATION RANGE The AD5251/AD5252 are designed with internal ESD diodes for protection; these diodes also set the boundaries for the terminal operating voltages. Positive signals present on Terminal A, Terminal B, or Terminal W that exceed VDD are clamped by the forwardbiased diode. Similarly, negative signals on Terminal A, Terminal B, or Terminal W that are more negative than VSS are also clamped (see Figure 38). In practice, users should not operate VAB, VWA, and VWB to be higher than the voltage across VDD to VSS, but VAB, VWA, and VWB have no polarity constraint. Figure 38. Maximum Terminal Voltages Set by VDD and VSS POWER-UP AND POWER-DOWN SEQUENCES Figure 36. Equivalent WP Digital Input MULTIPLE DEVICES ON ONE BUS The AD5251/AD5252 are equipped with two addressing pins, AD1 and AD0, that allow up to four AD5251/AD5252 devices to be operated on one I2C bus. To achieve this result, the states of AD1 and AD0 on each device must first be defined. An example is shown in Table 12 and Figure 37. In I2C programming, each device is issued a different slave address—01011(AD1)(AD0)—to complete the addressing. Table 12. Multiple Devices Addressing AD1 AD0 Device Addressed 0 0 1 1 0 1 0 1 U1 U2 U3 U4 Because the ESD protection diodes limit the voltage compliance at Terminal A, Terminal B, and Terminal W (see Figure 38), it is important to power on VDD/VSS before applying any voltage to these terminals. Otherwise, the diodes are forward biased such that VDD/VSS are powered unintentionally and may affect the user’s circuit. Similarly, VDD/VSS should be powered down last. The ideal power-up sequence is in the following order: GND, VDD, VSS, digital inputs, and VA/VB/VW. The order of powering VA, VB, VW, and the digital inputs is not important, as long as they are powered after VDD/VSS. LAYOUT AND POWER SUPPLY BIASING It is always a good practice to employ a compact, minimum leadlength layout design. The leads to the input should be as direct as possible, with a minimum conductor length. Ground paths should have low resistance and low inductance. Similarly, it is also good practice to bypass the power supplies with quality capacitors. Low equivalent series resistance (ESR) 1 µF to 10 µF tantalum or electrolytic capacitors should be applied at the supplies to minimize any transient disturbance and filter low frequency ripple. Figure 39 illustrates the basic supply-bypassing configuration for the AD5251/AD5252. Figure 39. Power Supply-Bypassing Configuration Figure 37. Multiple AD5251/AD5252 Devices on a Single Bus analog.com Rev. F | 23 of 27 Data Sheet AD5251/AD5252 THEORY OF OPERATION The ground pin of the AD5251/AD5252 is used primarily as a digital ground reference. To minimize the digital ground bounce, the AD5251/AD5252 ground terminal should be joined remotely to the common ground (see Figure 39). DIGITAL POTENTIOMETER OPERATION The structure of the RDAC is designed to emulate the performance of a mechanical potentiometer. The RDAC contains a string of resistor segments with an array of analog switches that act as the wiper connection to the resistor array. The number of points is the resolution of the device. For example, the AD5251/AD5252 emulate 64/256 connection points with 64/256 equal resistance, RS, allowing them to provide better than 1.5%/0.4% resolution. Figure 40 provides an equivalent diagram of the connections between the three terminals that make up one channel of the RDAC. Switches SWA and SWB are always on, but only one of switches SW(0) to SW(2N – 1) can be on at a time (determined by the setting decoded from the data bit). Because the switches are nonideal, there is a 75 Ω wiper resistance, RW. Wiper resistance is a function of supply voltage and temperature: Lower supply voltages and higher temperatures result in higher wiper resistances. Consideration of wiper resistance dynamics is important in applications in which accurate prediction of output resistance is required. wiper contact resistance, RW, of 75 Ω, regardless of the nominal resistance. The second connection (the AD5251 10 kΩ part) is the first tap point where RWB = 231 Ω (RWB = RAB/64 + RW = 156 Ω + 75 Ω) for Data 0x01, and so on. Each LSB data value increase moves the wiper up the resistor ladder until the last tap point is reached at RWB = 9893 Ω. See Figure 40 for a simplified diagram of the equivalent RDAC circuit. The general equation that determines the digitally programmed output resistance between W and B is AD5251: RWB D = D/64 × RAB + 75   Ω AD5252: RWB D = D/256 × RAB + 75   Ω (1) (2) where: D is the decimal equivalent of the data contained in the RDAC latch. RAB is the nominal end-to-end resistance. Figure 42. AD5251 RWA(D) and RWB(D) vs. Decimal Code Figure 40. Equivalent RDAC Structure PROGRAMMABLE RHEOSTAT OPERATION If either the W-to-B or W-to-A terminal is used as a variable resistor, the unused terminal can be opened or shorted with W; such operation is called rheostat mode (see Figure 41). The resistance tolerance can range ±20%. Figure 41. Rheostat Mode Configuration The nominal resistance of the AD5251/AD5252 has 64/256 contact points accessed by the wiper terminal, plus the B terminal contact. The 6-/8-bit data-word in the RDAC register is decoded to select one of the 64/256 settings. The wiper’s first connection starts at the B terminal for Data 0x00. This B terminal connection has a analog.com Since the digital potentiometer is not ideal, a 75 Ω finite wiper resistance is present that can easily be seen when the device is programmed at zero scale. Because of the fine geometric and interconnects employed by the device, care should be taken to limit the current conduction between W and B to no more than ±5 mA continuous for a total resistance of 1 kΩ or a pulse of ±20 mA to avoid degradation or possible destruction of the device. The maximum dc current for AD5251 and AD5252 are shown in Figure 21 and Figure 22, respectively. Similar to the mechanical potentiometer, the resistance of the RDAC between Wiper W and Terminal A also produces a digitally controlled complementary resistance, RWA. When these terminals are used, the B terminal can be opened. The RWA starts at a maximum value and decreases as the data loaded into the latch increases in value (see Figure 42). The general equation for this operation is AD5251: RWA D = AD5252: RWA D = 64 – D /64 × RAB + 75 Ω 256 – D /256 × RAB + 75 Ω (3) (4) Rev. F | 24 of 27 Data Sheet AD5251/AD5252 THEORY OF OPERATION The typical distribution of RAB from channel-to-channel matches is about ±0.15% within a given device. On the other hand, device-todevice matching is process-lot dependent with a ±20% tolerance. A more accurate calculation that includes the wiper resistance effect is PROGRAMMABLE POTENTIOMETER OPERATION VW(D) = If all three terminals are used, the operation is called potentiometer mode (see Figure 43); the most common configuration is the voltage divider operation. Figure 43. Potentiometer Mode Configuration If the wiper resistance is ignored, the transfer function is simply AD5251: VW = AD5252: VW = analog.com D 64 × VAB + VB D 256 × VAB + VB (5) D RAB + RW 2N RAB + 2RW VA (7) where 2N is the number of steps. Unlike in rheostat mode operation, where the tolerance is high, potentiometer mode operation yields an almost ratiometric function of D/2N with a relatively small error contributed by the RW terms. Therefore, the tolerance effect is almost canceled. Similarly, the ratiometric adjustment also reduces the temperature coefficient effect to 50 ppm/°C, except at low value codes where RW dominates. Potentiometer mode operations include other applications, such as op amp input, feedback-resistor networks, and other voltage-scaling applications. The A, W, and B terminals can, in fact, be input or output terminals, provided that |VA|, |VW|, and |VB| do not exceed VDD to VSS. (6) Rev. F | 25 of 27 Data Sheet AD5251/AD5252 APPLICATIONS INFORMATION LCD PANEL VCOM ADJUSTMENT Large LCD panels usually require an adjustable VCOM voltage centered around 6 V to 8 V with ±1 V swing and small steps adjustment. This example represents common DAC applications where the window of adjustments is small and centered at any level. High voltage and high resolution DACs can be used, but it is far more cost-effective to use low voltage digital potentiometers with level shifting, such as the AD5251 or AD5252, to achieve the objective. Assume a VCOM voltage requirement of 6 V ± 1 V with a ±20 mV step adjustment, as shown in Figure 44. The AD5252 can be configured in voltage divider mode with an op amp gain. With ±20% tolerance accounted for by the AD5252, this circuit can still be adjusted from 5 V to 7 V with an 8 mV/step in the worst case. Figure 45. Current-Sensing Amplifier ADJUSTABLE HIGH POWER LED DRIVER Figure 46 shows a circuit that can drive three or four high power LEDs. The ADP1610 is an adjustable boost regulator that provides adequate headroom and current for the LEDs. Because its FB pin voltage is 1.2 V, the digital potentiometer AD5252 and the op amp form an average gain of 12 feedback networks that servo the sensing and feedback voltages. As a result, the voltage across RSET is regulated around 0.1 V, depending on the AD5252’s setting. An adjustable LED current is ILED = Figure 44. Apply 5 V Digital Potentiometer AD5251 in a 6 V ± 1 V Application VR SET RSET (9) RSET should be small enough to conserve power, but large enough to limit the maximum LED current. R3 should be used in parallel with the AD5252 to limit the LED current to an achievable range. CURRENT-SENSING AMPLIFIER The dual-channel, synchronous update, and channel-to-channel resistance matching characteristics make the AD5251/AD5252 suitable for current-sensing applications, such as LED brightness control. In the circuit shown in Figure 45, when RDAC1 and RDAC3 are programmed to the same settings, it can be shown that Vo = D 2N − D V2 − V1 + VREF (8) As a result, the current through a sense resistor connected between V1 and V2 can be determined. The circuit can be programmed for use with systems that require different sensitivities. If the op amp has very low offset and low bias current, the major source of error comes from the digital potentiometer channel-to-channel resistance mismatch, which is typically 0.15%. The circuit accuracy is about 9 bits, which is adequate for LED control and other general-purpose applications. analog.com Figure 46. High Power, Adjustable LED Driver Rev. F | 26 of 27 Data Sheet AD5251/AD5252 OUTLINE DIMENSIONS Figure 47. 14-Lead Thin Shrink Small Outline Package [TSSOP] (RU-14) Dimensions shown in millimeters ORDERING GUIDE Model1, 2 Step RAB (kΩ) Temperature Range Package Description Package Option Ordering Quantity AD5251BRUZ50 AD5252BRUZ1 AD5252BRUZ1-RL7 AD5252BRUZ10 AD5252BRUZ10-RL7 AD5252BRUZ50 AD5252BRUZ50-RL7 AD5252BRUZ100 AD5252BRUZ100-RL7 64 256 256 256 256 256 256 256 256 50 1 1 10 10 50 50 100 100 −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 96 96 1,000 96 1,000 96 1,000 96 1,000 1 In the package marking, Line 1 shows the part number. Line 2 shows the branding information, such that B1 = 1 kΩ, B10 = 10 kΩ, and so on. There is also a “#” marking for the Pb-free part. Line 3 shows the date code in YYWW. 2 Z = RoHS Compliant Part. EVALUATION BOARDS Model1 Package Description EVAL-AD5252SDZ Evaluation Board 1 The EVAL-AD5252SDZ can be used to evaluate the AD5251 and the AD5252. I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors). ©2004-2022 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. One Analog Way, Wilmington, MA 01887-2356, U.S.A. Rev. F | 27 of 27