AD5282BRU50-REEL7

Single/Dual, +15 V/±5 V, 256-Position, I2C-Compatible Digital Potentiometer AD5280/AD5282 APPLICATIONS The AD5280/AD5282 are available in thin, surface-mounted 14-lead TSSOP and 16-lead TSSOP. All parts are guaranteed to operate over the extended industrial temperature range of −40°C to +85°C. For 3-wire SPI-compatible interface applications, see the AD5260/AD5262 product information on www.analog.com. FUNCTIONAL BLOCK DIAGRAMS A O1 O2 VDD VL VSS RDAC REGISTER OUTPUT REGISTER ADDRESS CODE 8 PWR ON RESET SCL SERIAL INPUT REGISTER SDA GENERAL DESCRIPTION Wiper position programming defaults to midscale at system power-on. When powered, the VR wiper position is programmed by an I2C-compatible, 2-wire serial data interface. The AD5280/ AD5282 feature sleep mode programmability. This allows any level of preset in power-up and is an alternative to a costly EEPROM solution. Both parts have additional programmable B SHDN Multimedia, video, and audio Communications Mechanical potentiometer replacement Instrumentation: gain, offset adjustment Programmable voltage source Programmable current source Line impedance matching The AD5280/AD5282 are single-channel and dual-channel, 256-position, digitally controlled variable resistors (VRs) 2 . The devices perform the same electronic adjustment function as a potentiometer, trimmer, or variable resistor. Each VR offers a completely programmable value of resistance between the A terminal and the wiper or the B terminal and the wiper. The fixed A-to-B terminal resistance of 20 kΩ, 50 kΩ, or 200 kΩ has a 1% channel-to-channel matching tolerance. The nominal temperature coefficient of both parts is 30 parts per million/ degrees centigrade (ppm/°C). Another key feature is that the parts can operate up to +15 V or ±5 V. W GND AD5280 AD0 AD1 Figure 1. AD5280 A1 W1 B1 A2 W2 B2 O1 OUTPUT REGISTER SHDN VDD VL VSS RDAC1 REGISTER RDAC2 REGISTER ADDRESS CODE 8 PWR ON RESET SCL SERIAL INPUT REGISTER SDA GND AD5282 AD0 02929-001 AD5280: 1 channel AD5282: 2 channels 256 positions +10 V to +15 V single supply; ±5.5 V dual-supply operation Fixed terminal resistance: 20 kΩ, 50 kΩ, 200 kΩ Low temperature coefficient: 30 ppm/°C Power-on midscale preset 1 Programmable reset Operating temperature: −40oC to +85oC I2C-compatible interface logic outputs that enable users to drive digital loads, logic gates, LED drivers, and analog switches in their system. 02929-070 FEATURES AD1 Figure 2. AD5282 1 Assert shutdown and program the device during power-up, then deassert the shutdown to achieve the desired preset level. 2 The terms digital potentiometer, VR, and RDAC are used interchangeably. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2002–2009 Analog Devices, Inc. All rights reserved. AD5280/AD5282 TABLE OF CONTENTS Features .............................................................................................. 1  Multiple Devices on One Bus ................................................... 17  Applications ....................................................................................... 1  Level Shift for Bidirectional Interface...................................... 18  General Description ......................................................................... 1  Level Shift for Negative Voltage Operation ............................ 18  Functional Block Diagrams ............................................................. 1  ESD Protection ........................................................................... 18  Revision History ............................................................................... 2  Terminal Voltage Operating Range ......................................... 18  Specifications..................................................................................... 3  Power-Up Sequence ................................................................... 18  Electrical Characteristics ............................................................. 3  Layout and Power Supply Bypassing ....................................... 19  Absolute Maximum Ratings............................................................ 5  Applications Information .............................................................. 20  Thermal Resistance ...................................................................... 5  Bipolar DC or AC Operation from Dual Supplies ................. 20  ESD Caution .................................................................................. 5  Gain Control Compensation .................................................... 20  Pin Configurations and Function Descriptions ........................... 6  15 V, 8-Bit I2C DAC.................................................................... 20  Typical Performance Characteristics ............................................. 7  8-Bit Bipolar DAC ...................................................................... 21  Test Circuits ..................................................................................... 12  Bipolar Programmable Gain Amplifier ................................... 21  Theory of Operation ...................................................................... 14  Programmable Voltage Source with Boosted Output ........... 21  Rheostat Operation .................................................................... 14  Programmable Current Source ................................................ 22  Potentiometer Operation........................................................... 14  Programmable Bidirectional Current Source ......................... 22  Digital Interface .............................................................................. 16  Programmable Low-Pass Filter ................................................ 23  2-Wire Serial Bus ........................................................................ 16  Programmable Oscillator .......................................................... 23  Readback RDAC Value .............................................................. 17  RDAC Circuit Simulation Model ............................................. 24  Additional Programmable Logic Output ................................ 17  Macro Model Net List for RDAC ............................................. 24  Self-Contained Shutdown Function and Programmable Preset ............................................................................................ 17  Outline Dimensions ....................................................................... 25  Ordering Guide .......................................................................... 26  REVISION HISTORY 7/09—Rev. B to Rev. C Changes to Features Section............................................................ 1 Updated Outline Dimensions, RU-14 ......................................... 25 Changes to Ordering Guide .......................................................... 26 8/07—Rev. A to Rev. B Updated Operating Temperature Range Throughout ................... 1 Changes to the Features Section ....................................................... 1 Changes to the General Description Section .................................. 1 Changes to Table 2 .............................................................................. 3 Added the Thermal Resistance Section ........................................... 5 Changes to the Ordering Guide......................................................26 11/05—Rev. 0 to Rev. A Updated Format ................................................................... Universal Updated Outline Dimensions .........................................................26 Changes to Ordering Guide ............................................................27 10/02—Revision 0: Initial Version Rev. C | Page 2 of 28 AD5280/AD5282 SPECIFICATIONS ELECTRICAL CHARACTERISTICS VDD = +15 V, VSS = 0 V or VDD = +5 V, VSS = −5 V; VLOGIC = 5 V, VA = +VDD, VB = 0 V; −40°C < TA < +85°C, unless otherwise noted. Table 1. Parameter Symbol Conditions DC CHARACTERISTICS–RHEOSTAT MODE Resistor Differential NL 2 R-DNL RWB, VA = NC Resistor Nonlinearity2 R-INL RWB, VA = NC Nominal Resistor Tolerance 3 ΔRAB TA = 25°C VAB = VDD, wiper = no connect Resistance Temperature (∆RAB/RAB)/∆T x 106 Coefficient Wiper Resistance RW IW = VDD/R, VDD = 3 V or 5 V DC CHARACTERISTICS–POTENTIOMETER DIVIDER MODE (specifications apply to all VRs) Resolution N Integral Nonlinearity 4 INL Differential Nonlinearity4 DNL Code = 0x80 (∆VW/VW)/∆T x 106 Voltage Divider Temperature Coefficient Full-Scale Error VWFSE Code = 0xFF Zero-Scale Error VWZSE Code = 0x00 RESISTOR TERMINALS Voltage Range 5 VA, VB, VW 6 Capacitance A, B CA, CB f = 5 MHz, measured to GND, Code = 0x80 Capacitance W6 CW f = 1 MHz, measured to GND, Code = 0x80 Common-Mode Leakage ICM V A = VB = V W Shutdown Current ISHDN DIGITAL INPUTS AND OUTPUTS Input Logic High VIH Input Logic Low VIL Output Logic High (O1, O2) VIH Output Logic Low (O1, O2) VIL Input Current IIL VIN = 0 V or 5 V Input Capacitance6 CIL POWER SUPPLIES Logic Supply VLOGIC Power Single-Supply Range VDD RANGE VSS = 0 V Power Dual-Supply Range VDD/SS RANGE Logic Supply Current ILOGIC VLOGIC = 5 V Positive Supply Current IDD VIH = 5 V or VIL = 0 V Negative Supply Current ISS Power Dissipation 7 PDISS VIH = 5 V or VIL = 0 V, VDD = +5 V, VSS = −5 V Power Supply Sensitivity PSS DYNAMIC CHARACTERISTICS6, 8, 9 Bandwidth −3 dB BW_20K RAB = 20 kΩ, Code = 0x80 BW_50K RAB = 50 kΩ, Code = 0x80 BW_200K RAB = 200 kΩ, Code = 0x80 Rev. C | Page 3 of 28 Min Typ 1 Max Unit −1 −1 −30 ±1/4 ±1/4 +1 +1 +30 LSB LSB % ppm/°C 60 150 Ω ±1/4 ±1/4 5 +1 +1 Bits LSB LSB ppm/°C −1 +1 0 +2 LSB LSB VDD 25 V pF 55 pF 30 8 −1 −1 −2 0 VSS 1 5 0.7 × VL 0 4.9 VL + 0.5 0.3 × VL 0.4 ±1 5 2.7 4.5 ±4.5 nA μA V V V V μA pF 0.1 0.1 0.2 VDD 16.5 ±5.5 60 1 1 0.3 V V V μA μA μA mW 0.002 0.01 %/% 310 150 35 kHz kHz kHz AD5280/AD5282 Parameter Total Harmonic Distortion Symbol THDW VW Settling Time Crosstalk tS CT Analog Crosstalk CTA Conditions VA = 1 V rms, RAB = 20 kΩ VB = 0 V dc, f = 1 kHz VA = 5 V, VB = 5 V, ±1 LSB error band VA = VDD, VB = 0 V, measure VW1 with adjacent RDAC making full-scale code change Measure VW1 with VW2 = 5 V p-p @ f = 10 kHz RWB = 20 kΩ, f = 1 kHz Resistor Noise Voltage eN_WB INTERFACE TIMING CHARACTERISTICS (applies to all parts)6, 10, 11 SCL Clock Frequency fSCL t1 tBUF Bus Free Time Between Stop and Start t2 tHD:STA Hold Time (Repeated After this period, the first clock pulse Start) is generated tLOW Low Period of SCL Clock t3 tHIGH High Period of SCL Clock t4 t5 tSU:STA Setup Time for Start Condition tHD:DAT Data Hold Time t6 tSU:DAT Data Setup Time t7 t8 tF Fall Time of Both SDA and SCL Signals t9 tR Rise Time of Both SDA and SCL Signals t10 tSU:STO Setup Time for STOP Condition Min Typ 1 0.014 Max Unit % 5 15 μs nV-s −62 dB 18 nV/√Hz 1.3 kHz μs 0.6 μs 1.3 0.6 0.6 μs μs μs 0 0 400 0.9 300 μs ns ns 300 ns 100 0.6 μs 1 Typicals represent average readings at 25°C, VDD = +5 V, VSS = −5 V. Resistor position nonlinearity error R-INL is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic. 3 VAB = VDD, wiper (VW) = no connect. 4 INL and DNL are measured at VW with the RDAC configured as a potentiometer divider similar to a voltage output DAC. VA = VDD and VB = 0 V. DNL specification limits of ±1 LSB maximum are guaranteed monotonic operating conditions. 5 Resistor Terminal A, Resistor Terminal B, and Wiper Terminal W have no limitations on polarity with respect to each other. 6 Guaranteed by design and not subject to production test. 7 PDISS is calculated from (IDD × VDD). CMOS logic level inputs result in minimum power dissipation. 8 Bandwidth, noise, and settling time are dependent on the terminal resistance value chosen. The lowest R value results in the fastest settling time and highest bandwidth. The highest R value results in the minimum overall power consumption. 9 All dynamic characteristics use VDD = 5 V. 10 See timing diagram (Figure 3) for location of measured values. 11 Standard I2C mode operation is guaranteed by design. 2 t8 t6 t2 t9 SCL t2 t4 t3 t8 t7 t10 t5 t9 t1 P S S Figure 3. Detailed Timing Diagram Rev. C | Page 4 of 28 P 02929-042 SDA AD5280/AD5282 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 2. Parameter VDD to GND VSS to GND VDD to VSS VA, VB, VW to GND AX to BX, AX to WX, BX to WX Intermittent 1 Continuous VLOGIC to GND Output Voltage to GND Operating Temperature Range Maximum Junction Temperature (TJMAX) Storage Temperature Range Reflow Soldering Peak Temperature Time at Peak Temperature 1 Rating −0.3 V to +16.5 V 0 V to −7 V 16.5 V VSS to VDD Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL RESISTANCE ±20 mA ±5 mA 0 V to 7 V 0 V to 7 V −40°C to +85°C 150°C −65°C to +150°C 260°C 20 sec to 40 sec θJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Package power dissipation = (TJMAX − TA)/ θJA . Table 3. Thermal Resistance Package Type TSSOP-14 TSSOP-16 ESD CAUTION Maximum terminal current is bound by the maximum current handling of the switches, maximum power dissipation of the package, and maximum applied voltage across any two of the A, B, and W terminals at a given resistance. Rev. C | Page 5 of 28 θJA 206 150 Unit °C/W °C/W AD5280/AD5282 1 14 O1 O1 1 16 A2 2 13 VL A1 2 15 W2 B 3 12 O2 W1 3 14 B2 VDD 4 11 VSS B1 4 13 VL SHDN 5 10 GND VDD 5 12 VSS SCL 6 9 AD1 SHDN 6 11 GND SDA 7 8 AD0 SCL 7 10 AD1 SDA 8 9 AD0 AD5280 TOP VIEW 02929-002 A W Figure 4. AD5280 Pin Configuration AD5282 TOP VIEW Figure 5. AD5282 Pin Configuration Table 4. AD5280 Pin Function Descriptions Table 5. AD5282 Pin Function Descriptions Pin No. 1 2 3 4 Mnemonic A W B VDD Pin No. 1 2 3 4 5 Mnemonic O1 A1 W1 B1 VDD 5 SHDN 6 SHDN 7 8 9 SCL SDA AD0 10 AD1 11 12 GND VSS 13 VL 14 15 16 B2 W2 A2 6 7 8 SCL SDA AD0 9 AD1 10 11 GND VSS 12 13 O2 VL 14 O1 02929-003 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Description Resistor Terminal A. Wiper Terminal W. Resistor Terminal B. Positive Power Supply. Specified for operation from 5 V to 15 V (sum of |VDD| + |VSS| ≤ 15 V). Active Low, Asynchronous Connection of Wiper W to Terminal B and Open Circuit of Terminal A. RDAC register contents unchanged. SHDN should tie to VL if not used. Can also be used as a programmable preset in power-up. Serial Clock Input. Serial Data Input/Output. Programmable Address Bit 0 for Multiple Package Decoding. Bit AD0 and Bit AD1 provide four possible addresses. Programmable Address Bit 1 for Multiple Package Decoding. Bit AD0 and Bit AD1 provide four possible addresses. Common Ground. Negative Power Supply. Specified for operation from 0 V to −5 V (sum of |VDD| + |VSS| ≤ 15 V). Logic Output Terminal O2. Logic Supply Voltage. Needs to be less than or equal to VDD and at the same voltage as the digital logic controlling the AD5280. Logic Output Terminal O1. Rev. C | Page 6 of 28 Description Logic Output Terminal O1. Resistor Terminal A1. Wiper Terminal W1. Resistor Terminal B1. Positive Power Supply. Specified for operation from 5 V to 15 V (sum of |VDD| + |VSS| ≤ 15 V). Active Low, Asynchronous Connection of Wiper W to Terminal B and Open Circuit of Terminal A. RDAC register contents unchanged. SHDN should tie to VL if not used. Can be also used as a programmable preset in power-up. Serial Clock Input. Serial Data Input/Output. Programmable Address Bit 0 for Multiple Package Decoding. Bit AD0 and Bit AD1 provide four possible addresses. Programmable Address Bit 1 for Multiple Package Decoding. Bit AD0 and Bit AD1 provide four possible addresses. Common Ground. Negative Power Supply. Specified for operation from 0 V to −5 V (sum of |VDD| + |VSS| ≤ 15 V). Logic Supply Voltage. Needs to be less than or equal to VDD and at the same voltage as the digital logic controlling the AD5282. Resistor Terminal B2. Wiper Terminal W2. Resistor Terminal A2. AD5280/AD5282 TYPICAL PERFORMANCE CHARACTERISTICS 0.5 RAB = 20kΩ TA = 25°C POTENTIOMETER MODE DNL (LSB) 0.6 +5V 0.4 0.2 0 –0.2 ±5V –0.4 +15V –0.6 –0.8 –1.0 0 32 64 96 128 160 CODE (Decimal) 192 224 RAB = 20kΩ 0.4 02929-004 RHEOSTAT MODE R-INL (LSB) 0.8 0.3 0.2 TA = –40°C 0.1 0 –0.1 –0.2 –0.3 TA = +25°C –0.4 –0.5 256 0 32 Figure 6. R-INL vs. Code vs. Supply Voltages 224 256 +15V 0.1 0 –0.1 –0.2 +5V –0.3 0 32 64 96 128 160 CODE (Decimal) 192 224 RAB = 20kΩ TA = 25°C 0.6 ±5V 0.4 +5V 0.2 +15V 0 –0.2 –0.4 –0.6 02929-008 POTENTIOMETER MODE INL (LSB) ±5V 0.2 02929-005 RHEOSTAT MODE R-DNL (LSB) 192 0.8 0.3 –0.8 –0.8 –1.0 256 0 Figure 7. R-DNL vs. Code vs. Supply Voltages 32 64 96 128 160 CODE (Decimal) 192 224 256 Figure 10. INL vs. Code vs. Supply Voltages 1.0 0.5 RAB = 20kΩ TA = +85°C 0.2 0 –0.2 TA = –40°C –0.4 TA = +25°C 02929-006 –0.6 –0.8 0 32 64 96 128 160 CODE (Decimal) 192 224 0.3 +5V 0.2 ±5V 0.1 +15V 0 –0.1 –0.2 –0.3 02929-009 0.6 0.4 RAB = 20kΩ TA = 25°C 0.4 POTENTIOMETER MODE INL (LSB) 0.8 POTENTIOMETER MODE INL (LSB) 96 128 160 CODE (Decimal) 1.0 RAB = 20kΩ TA = 25°C 0.4 –1.0 64 Figure 9. DNL vs. Code, VDD/VSS = ±5 V 0.5 –0.5 TA = +85°C 02929-007 1.0 –0.4 –0.5 256 Figure 8. INL vs. Code, VDD/VSS = ±5 V 0 32 64 96 128 160 CODE (Decimal) 192 224 Figure 11. DNL vs. Code vs. Supply Voltages Rev. C | Page 7 of 28 256 AD5280/AD5282 1.0 2.0 RAB = 20kΩ TA = 25°C AVG +3σ AVG –3σ 0 02929-010 –0.5 5 10 |VDD – VSS| (V) 15 1.2 1.0 0.4 0.2 0 –40 20 60 AVG +3σ IDD/ISS SUPPLY CURRENT (nA) R-INL (LSB) 20 40 TEMPERATURE (°C) RAB = 20kΩ AVG 0.5 AVG –3σ 0 –0.5 –1.0 0 5 10 |VDD – VSS| (V) 100 15 VLOGIC = +5V VIH = +5V VIL = 0V 100 |SS@VDD/VSS = +15V/0V 10 1 –40 20 |SS@VDD/VSS = ±5V –7 26 TEMPERATURE (°C) 59 85 Figure 16. Supply Current vs. Temperature Figure 13. R-INL Over Supply Voltage 26.0 0 RAB = 20kΩ –0.2 RAB = 20kΩ 25.5 –0.4 VDD/VSS = +15V/0V VDD/VSS = +15V/0V –0.6 25.0 –1.0 ILOGIC (µA) –0.8 VDD/VSS = ±5V –1.2 –1.4 24.5 24.0 VDD/VSS = +5V/0V VDD/VSS = ±5V –1.6 02929-012 23.5 –1.8 –2.0 –40 80 |DD@VDD/VSS = ±5V 02929-011 –1.5 FULL-SCALE ERROR (LSB) 0 1000 1.0 –2.0 –20 Figure 15. Zero-Scale Error RAB = 20kΩ TA = 25°C 1.5 VDD/VSS = +15V/0V 0.6 Figure 12. INL Over Supply Voltage 2.0 VDD/VSS = ±5V 0.8 02929-014 0 VDD/VSS = +5V/0V 1.4 –20 0 20 40 TEMPERATURE (°C) 60 80 23.0 –40 100 02929-015 INL (LSB) AVG 02929-013 ZERO-SCALE ERROR (LSB) 1.6 0.5 –1.0 RAB = 20kΩ 1.8 –7 26 TEMPERATURE (°C) 59 Figure 17. VLOGIC Supply Current vs. Temperature Figure 14. Full-Scale Error Rev. C | Page 8 of 28 85 AD5280/AD5282 1000 0 RAB = 20kΩ TA = 25°C 80H –6 40H 20H –18 100 10H –24 08H –30 04H –36 02H 01H –42 –48 0 1 2 3 4 TA = 25°C VA = 50mV rms VDD/VSS = ±5V –54 –60 5 0 VIH (V) Figure 18. VLOGIC Supply Current vs. Digital Input Voltage 0 80H –6 40H –12 20H –18 GAIN (dB) 400 300 20kΩ 200 50kΩ 200kΩ 100 10H –24 08H –30 04H –36 02H –42 0 01H –48 –100 0 32 64 96 128 CODE (Decimal) 192 224 TA = 25°C VA = 50mV rms VDD/VSS = ±5 –54 –60 256 0 1M Figure 22. Gain vs. Frequency vs. Code, RAB = 50 kΩ Figure 19. Rheostat Mode Tempco ΔRWB/ΔT vs. Code, VDD/VSS = ±5 V 0 120 TA = 25°C 80H –6 100 40H –12 80 60 20H –18 20kΩ GAIN (dB) 50kΩ 200kΩ 40 20 10H –24 08H –30 04H –36 02H –42 0 01H –48 –20 02929-018 POTENTIOMETER MODE TEMPCO (ppm/°C) 10k 100k FREQUENCY (Hz) 02929-020 500 02929-017 RHEOSTAT MODE TEMPCO (ppm/°C) TA = 25°C 600 –40 1M Figure 21. Gain vs. Frequency vs. Code, RAB = 20 kΩ 700 –200 10k 100k FREQUENCY (Hz) 0 32 64 96 128 CODE (Decimal) 192 224 TA = 25°C VA = 50mV rms VDD/VSS = ±5V –54 –60 256 0 10k 100k FREQUENCY (Hz) Figure 23. Gain vs. Frequency vs. Code, RAB = 200 kΩ Figure 20. Potentiometer Mode Tempco ΔVWB/ΔT vs. Code, VDD/VSS = ±5 V Rev. C | Page 9 of 28 02929-021 10 02929-016 VDD/VSS = 5V/0V VLOGIC = 3V 02929-019 VDD/VSS = 5V/0V VLOGIC = 5V GAIN (dB) ILOGIC (µA) –12 1M AD5280/AD5282 0 80 R = 20kΩ 310kHz –6 CODE = 80H, VA = VDD, VB = 0V –12 PSRR (dB) R = 200kΩ 35kHz –36 40 –42 +PSRR @ VDD/VSS = ±5V DC ±10% p-p AC –60 0 02929-022 TA = 25°C VDD/VSS = ±5V VA = 50mV rms –54 10k 100k FREQUENCY (Hz) 02929-025 20 –48 0 100 1M 1000 100k 1M Figure 27. PSRR vs. Frequency Figure 24. −3 dB Bandwidth TA = 25°C VDD/VSS = ±5V A2 1.2V 852.0µs R = 20kΩ –6dB R = 50kΩ R = 200kΩ 02929-023 NOMINALIZED GAIN FLATNESS (0.1dB/DIV) 10k FREQUENCY (MHz) 100 1k 10k FREQUENCY (Hz) 02929-026 GAIN (dB) –24 –30 –PSRR @ V DD/VSS = ±5V DC ±10% p-p AC 60 R = 50kΩ 150kHz –18 2.04µs 100k Figure 25. Normalized Gain Flatness vs. Frequency Figure 28. Midscale Glitch Energy Code 0x80 to 0x7F 500 T TA = 25°C VDD/VSS = ±5V +5V VW 1 300 –5V CODE = 55H 200 CS 100 0 10k 100k 1M FREQUENCY (Hz) 10M Figure 26. VLOGIC Supply Current vs. Frequency 2 02929-027 CODE = 55H 02929-024 ILOGIC (mA) 400 CH1 5.00V CH2 5.00V M100ns A CH1 Figure 29. Large Signal Settling Time Rev. C | Page 10 of 28 0V AD5280/AD5282 40 A2 1.0V 33.41µs FREQUENCY (MHz) 30 CODES SET TO MIDSCALE 3 LOTS SAMPLE SIZE = 135 20 02929-030 0.2 0.1 0.15 0 0.05 –0.05 –0.1 –0.2 –0.15 –0.3 –0.25 –0.4 –0.35 0 –0.5 1.50µs –0.45 02929-028 10 LONG TERM CHANNEL-TO-CHANNEL RAB MATCH (%) Figure 30. Digital Feedthrough vs. Time VA = VB = OPEN TA = 25°C 10 1.0 RAB = 20kΩ RAB = 50kΩ 0.1 RAB = 200kΩ 0.01 02929-029 THEORETICAL |WB_MAX (mA) 100 Figure 32. Channel-to-Channel Resistance Matching (AD5282) 0 32 64 96 128 CODE (Decimal) 192 224 256 Figure 31. IWB_MAX vs. Code Rev. C | Page 11 of 28 AD5280/AD5282 TEST CIRCUITS Figure 33 to Figure 43 define the test conditions used in the product specification table. DUT VIN B VMS B 5V W W OP279 OFFSET GND 02929-031 A V+ A V+ = VDD 1LSB = V+/2N OFFSET BIAS Figure 37. Inverting Gain Figure 33. Potentiometer Divider Nonlinearity Error (INL, DNL) 5V NO CONNECT IW OP279 VIN W VMS A VW W B Figure 38. Noninverting Gain VIN +15V W DUT VOUT AD8610 OFFSET GND 02929-033 VMS1 RW = [VMS1 –VMS2]/IW B ) ΔVMS% ΔVDD% W B VMS 0.1V RSW = I SW DUT 02929-034 V+ W ( ΔVMS ΔVDD ISW VSS TO VDD Figure 36. Power Supply Sensitivity (PSS, PSSR) 0.1V 02929-038 PSRR (dB) = 20 LOG A Figure 39. Gain vs. Frequency V+ = VDD ±10% PSS (%/%) = –15V 2.5V Figure 35. Wiper Resistance VA B 02929-037 B VDD DUT IW = VDD/RNOMINAL DUT VMS2 A OFFSET BIAS Figure 34. Resistor Position Nonlinearity Error (Rheostat Operation; R-INL, R-DNL) A W OFFSET GND 02929-032 B VOUT 02929-036 DUT A VOUT 02929-035 DUT Figure 40. Incremental On Resistance Rev. C | Page 12 of 28 AD5280/AD5282 A VSS B GND W ICM VIN VCM NC 02929-039 VDD DUT VDD A1 NC = NO CONNECT N/C RDAC 1 W1 B1 A2 RDAC 2 W2 VSS CTA = 20 LOG [VOUT/VIN] B2 Figure 43. Analog Crosstalk (AD5282 Only) Figure 41. Common-Mode Leakage Current VLOGIC VOUT 02929-041 NC ILOGIC SCL SCA 02929-040 DIGITAL INPUT VOLTAGE Figure 42. VLOGIC Current vs. Digital Input Voltage Rev. C | Page 13 of 28 AD5280/AD5282 THEORY OF OPERATION The AD5280/AD5282 are single-channel and dual-channel, 256-position, digitally controlled variable resistors (VRs). To program the VR settings, see the Digital Interface section. Both parts have an internal power-on preset that places the wiper at midscale during power-on, which simplifies the fault condition recovery at power-up. Operation of the power-on preset function also depends on the state of the VL pin. SWA AX SHDN RS RDAC LATCH AND DECODER RS 0xFF RS WX 0x01 RS SWB 0x00 BX 02929-045 D7 D6 D5 D4 D3 D2 D1 D0 Figure 44. AD5280/AD5282 Equivalent RDAC Circuit RHEOSTAT OPERATION The nominal resistance of the RDAC between Terminal A and Terminal B is available in 20 kΩ, 50 kΩ, and 200 kΩ. The final two or three digits of the part number determine the nominal resistance value, for example, 20 kΩ = 20, 50 kΩ = 50, and 200 kΩ = 200. The nominal resistance (RAB) of the VR has 256 contact points accessed by the wiper terminal, plus the B terminal contact. The eight-bit data in the RDAC latch is decoded to select one of the 256 possible settings. Assuming that a 20 kΩ part is used, the wiper’s first connection starts at the B terminal for data 0x00. Because there is a 60 Ω wiper contact resistance, such a connection yields a minimum of 60 Ω resistance between Terminal W and Terminal B. The second connection is the first tap point that corresponds to 138 Ω (RWB = RAB/256 + RW = 78 Ω + 60 Ω) for data 0x01. The third connection is the next tap point representing 216 Ω (78 × 2 + 60) for data 0x02, and so on. Each LSB data value increase moves the wiper up the resistor ladder until the last tap point is reached at 19,982 Ω (RAB – 1 LSB + RW). Figure 46 shows a simplified diagram of the equivalent RDAC circuit where the last resistor string is not accessed; therefore, there is 1 LSB less of the nominal resistance at full scale in addition to the wiper resistance. The general equation determining the digitally programmed output resistance between W and B is RWB (D ) = D × RAB + RW 256 (1) where: D is the decimal equivalent of the binary code loaded in the 8bit RDAC register. RAB is the nominal end-to-end resistance. RW is the wiper resistance contributed by the on resistance of the internal switch. Note that in the zero-scale condition, a finite wiper resistance of 60 Ω is present. Care should be taken to limit the current flow between W and B in this state to a maximum pulse current of no more than 20 mA. Otherwise, degradation or possible destruction of the internal switch contact can occur. As in the mechanical potentiometer, the resistance of the RDAC between Wiper W and Terminal A also produces a digitally controlled complementary resistance, RWA. When these terminals are used, the B terminal can be opened. Setting the resistance value for RWA starts at a maximum value of resistance and decreases as the data loaded in the latch increases in value. The general equation for this operation is 256 − D (2) RWA (D ) = × RAB + RW 256 The typical distribution of the nominal resistance, RAB, from channel to channel matches within ±1%. Device-to-device matching is process lot dependent, and it is possible to have a ±30% variation. Because the resistance element is processed in thin film technology, the change in RAB with temperature is very small (30 ppm/°C). POTENTIOMETER OPERATION The digital potentiometer easily generates a voltage divider at wiper to B and wiper to A to be proportional to the input voltage at A to B. Unlike the polarity of VDD – VSS, which must be positive, voltage across A to B, W to A, and W to B can be at either polarity, provided that VSS is powered by a negative supply. If the effect of the wiper resistance for approximation is ignored, connecting the A terminal to 5 V and the B terminal to ground produces an output voltage at the wiper to B starting at 0 V up to 1 LSB less than 5 V. Each LSB of voltage is equal to the voltage applied across A to B divided by the 256 positions of the potentiometer divider. Because the AD5280/AD5282 can be supplied by dual supplies, the general equation defining the output voltage at VW with respect to ground for any valid Rev. C | Page 14 of 28 AD5280/AD5282 input voltage applied to Terminal A and Terminal B is D 256 − D VW (D ) = VA + VB 256 256 Operation of the digital potentiometer in divider mode results in a more accurate operation over temperature. Unlike rheostat mode, the output voltage is dependent mainly on the ratio of the internal resistors RWA and RWB and not on the absolute values; therefore, the temperature drift reduces to 5 ppm/°C. (3) For a more accurate calculation that includes the effect of wiper resistance, VW can be found as VW (D ) = R (D ) RWB ( D ) VA + WA VB RAB RAB (4) 1 9 1 9 1 9 SCL 1 0 1 1 AD1 AD0 R/W A/B RS SD O1 O2 X X ACK. BY AD5280/5282 START BY MASTER X D7 D6 D5 D4 D3 D2 D1 ACK. BY AD5280/AD5282 FRAME 1 SLAVE ADDRESS BYTE FRAME 2 INSTRUCTION BYTE D0 ACK. BY AD5280/5282 STOP BY MASTER FRAME 3 DATA BYTE 02929-043 0 SDA Figure 45. Writing to the RDAC Register 9 1 1 9 SCL 1 0 1 1 AD1 AD0 R/W D7 D6 D5 D4 D3 D2 D1 D0 A ACK. BY AD5280/AD5282 START BY MASTER NO ACK. BY MASTER FRAME 2 STOP BY DATA BYTE FROM PREVIOUSLY SELECTED MASTER FRAME 1 SLAVE ADDRESS BYTE 02929-044 0 SDA Figure 46. Reading Data from a Previously Selected RDAC Register in Write Mode Table 6. Serial Format of Data Accepted from the I2C Bus S 0 1 0 1 1 AD1 AD 0 Slave Address Byte R/ W A A/B RS S D O1 O2 X X X Instruction Byte A D7 D6 D 5 D 4 D 3 D 2 D 1 Data Byte where: Abbreviation S P A X AD1, AD0 R/W A/B RS SD O2, O1 D7, D6, D5, D4, D3, D2, D1, D0 Equals Start condition Stop condition Acknowledge Don’t care Package pin programmable address bits Read enable at high and write enable at low RDAC subaddress select; 0 = RDAC1 and 1 = RDAC2 Midscale reset, active high (only affects selected channel) Shutdown; same as SHDN pin operation except inverse logic (only affects selected channel) Output logic pin latched values; default Logic 0 Data bits Rev. C | Page 15 of 28 D 0 A P AD5280/AD5282 DIGITAL INTERFACE 2-WIRE SERIAL BUS The AD5280/AD5282 are controlled via an I2C-compatible serial bus. The RDACs are connected to this bus as slave devices. As shown in Figure 45, Figure 46, and Table 6, the first byte of the AD5280/AD5282 is a slave address byte. It has a 7-bit slave address and an R/W bit. The 5 MSBs are 01011, and the two bits that follow are determined by the state of the AD0 pin and the AD1 pin of the device. AD0 and AD1 allow the user to place up to four of the I2C-compatible devices on one bus. The 2-wire I2C serial bus protocol operates as follows. The master initiates data transfer by establishing a start condition, which happens when a high-to-low transition on the SDA line occurs while SCL is high (see Figure 45). The following byte is the slave address byte, which consists of the 7-bit slave address followed by an R/W bit (this bit determines whether data is read from or written to the slave device). The slave whose address corresponds to the transmitted address responds by pulling the SDA line low during the ninth clock pulse (this is called the acknowledge bit). At this stage, all other devices on the bus remain idle while the selected device waits for data to be written to or read from its serial register. If the R/W bit is high, the master reads from the slave device. On the other hand, if the R/W bit is low, the master writes to the slave device. A write operation contains one instruction byte more than a read operation. Such an instruction byte in write mode follows the slave address byte. The most significant bit (MSB) of the instruction byte labeled A/B is the RDAC subaddress select. A low selects RDAC1 and a high selects RDAC2 for the dual channel AD5282. Set A/B low for the AD5280. RS, the second MSB, is the midscale reset. A logic high on this bit moves the wiper of a selected channel to the center tap where RWA = RWB. This feature effectively writes over the contents of the register and thus, when taken out of reset mode, the RDAC remains at midscale. SD, the third MSB, is a shutdown bit. A logic high causes the selected channel to open circuit at Terminal A while shorting the wiper to Terminal B. This operation yields almost 0 Ω in rheostat mode or 0 V in potentiometer mode. This SD bit serves the same function as the SHDN pin except that the SHDN pin reacts to active low. Also, the SHDN pin affects both channels (AD5282) as opposed to the SD bit, which affects only the channel that is being written to. Note that the shutdown operation does not disturb the contents of the register. When brought out of shutdown, the previous setting is applied to the RDAC. The following two bits are O1 and O2. They are extra programmable logic outputs that can be used to drive other digital loads, logic gates, LED drivers, analog switches, and so on. The three LSBs are don’t care bits (see Figure 45). After acknowledging the instruction byte, the last byte in write mode is the data byte. Data is transmitted over the serial bus in sequences of nine clock pulses (eight data bits followed by an acknowledge bit). The transitions on the SDA line must occur during the low period of SCL and remain stable during the high period of SCL (see Figure 45). In read mode, the data byte follows immediately after the acknowledgment of the slave address byte. Data is transmitted over the serial bus in sequences of nine clock pulses (a slight difference from write mode, where there are eight data bits followed by an acknowledge bit). Similarly, the transitions on the SDA line must occur during the low period of SCL and remain stable during the high period of SCL (see Figure 46). When all data bits have been read or written, a stop condition is established by the master. A stop condition is defined as a lowto-high transition on the SDA line while SCL is high. In write mode, the master pulls the SDA line high during the tenth clock pulse to establish a stop condition (see Figure 45). In read mode, the master issues a no acknowledge for the ninth clock pulse (that is, the SDA line remains high). The master then brings the SDA line low before the 10th clock pulse, which goes high to establish a stop condition (see Figure 46). A repeated write function gives the user flexibility to update the RDAC output a number of times after addressing and instructing the part only once. During the write cycle, each data byte updates the RDAC output. For example, after the RDAC has acknowledged its slave address and instruction bytes, the RDAC output updates after these two bytes. If another byte is written to the RDAC while it is still addressed to a specific slave device with the same instruction, this byte updates the output of the selected slave device. If different instructions are needed, the write mode has to start with a new slave address, instruction, and data byte again. Similarly, a repeated read function of RDAC is also allowed. Rev. C | Page 16 of 28 AD5280/AD5282 READBACK RDAC VALUE ADDITIONAL PROGRAMMABLE LOGIC OUTPUT The AD5280/AD5282 feature additional programmable logic outputs, O1 and O2, which can be used to drive a digital load, analog switches, and logic gates. O1 and O2 default to Logic 0. The logic states of O1 and O2 can be programmed in Frame 2 under write mode (see Figure 45). These logic outputs have adequate current driving capability to sink/source milliamperes of load. In addition, shutdown can be implemented with the device digital output as shown in Figure 47. In this configuration, the device is shut down during power-up, but the user is allowed to program the device at any preset levels. When it is done, the user programs O1 high with the valid coding and the device exits from shutdown and responds to the new setting. This selfcontained shutdown function allows absolute shutdown during power-up, which is crucial in hazardous environments, without adding extra components. Also, the sleep mode programming feature during shutdown allows the AD5280/AD5282 to have a programmable preset at any level, a solution that can be as effective as using other high cost EEPROM devices. Because of the extra power drawn on RPD, note that a high value should be chosen for the RPD. O1 SHDN RPD SDA SCL Users can also activate O1 and O2 in three ways without affecting the wiper settings by programming as follows: • • Figure 47. Shutdown by Internal Logic Output Perform start, slave address, acknowledge, and instruction bytes with O1 and O2 specified, acknowledge, stop. Complete the write cycle with stop, then start, slave address byte, acknowledge, instruction byte with O1 and O2 specified, acknowledge, stop. Not complete the write cycle by not issuing the stop, then start, slave address byte, acknowledge, instruction byte with O1 and O2 specified, acknowledge, stop. MULTIPLE DEVICES ON ONE BUS Figure 48 shows four AD5282 devices on the same serial bus. Each has a different slave address because the states of their Pin AD0 and Pin AD1 are different. This allows each RDAC within each device to be written to or read from independently. The master device output bus line drivers are open-drain pulldowns in a fully I2C-compatible interface. 5V RP SELF-CONTAINED SHUTDOWN FUNCTION AND PROGRAMMABLE PRESET RP SDA MASTER Shutdown can be activated by strobing the SHDN pin or programming the SD bit in the write mode instruction byte. As shown in Figure 44, when shutdown is asserted, the AD5280/AD5282 open SWA to let the A terminal float and short the W terminal to the B terminal. The AD5280/AD5282 consume negligible power during shutdown mode, resuming the previous setting once the SHDN pin is released. Rev. C | Page 17 of 28 SCL SDA SCL AD1 AD0 AD5282 5V SDA SCL AD1 AD0 AD5282 5V SDA SCL AD1 5V SDA SCL AD1 AD0 AD0 AD5282 AD5282 Figure 48. Multiple AD5282 Devices on One Bus 02929-047 • 02929-046 The AD5280/AD5282 allow the user to read back the RDAC values in read mode. However, for the dual-channel AD5282, the channel of interest is the one that is previously selected in the write mode. When users need to read the RDAC values of both channels in the AD5282, they can program the first subaddress in write mode and then change to read mode to read the first channel value. After that, they can change back to write mode with the second subaddress and read the second channel value in read mode again. It is not necessary for users to issue the Frame 3 data byte in write mode for subsequent readback operation. Users should refer to Figure 45 and Figure 46 for the programming format. AD5280/AD5282 LEVEL SHIFT FOR BIDIRECTIONAL INTERFACE VDD While most old systems can be operated at one voltage, a new component can be optimized at another. When two systems operate the same signal at two different voltages, proper level shifting is needed. For instance, a 3.3 V EEPROM can interface with a 5 V digital potentiometer. A level-shift scheme is needed to enable a bidirectional communication so that the setting of the digital potentiometer can be stored to and retrieved from the EEPROM. Figure 49 shows one of the implementations. M1 and M2 can be any N-channel signal FETs or low threshold FDV301N if VDD falls below 2.5 V. 0 S SDA1 RP G RP D G S SCL1 D SCL2 M2 3.3V EEPROM 5V AD5282 Q2 R3 10kΩ VOUT 0 –5V VSS = –5V 02929-050 R2 10kΩ Figure 51. Level Shift for Bipolar Potential Operation ESD PROTECTION SDA2 M1 0 0 All digital inputs are protected with a series input resistor and parallel Zener ESD structures, as shown in Figure 52. The protection applies to digital inputs SDA, SCL, and SHDN. 02929-048 RP Q3 Q1 VDD2 = 5V RP VIN 340Ω LOGIC Figure 49. Level Shift for Different Potential Operation LEVEL SHIFT FOR NEGATIVE VOLTAGE OPERATION 02929-051 VDD1 = 3.3V +5V VSS Figure 52. ESD Protection of Digital Pins The digital potentiometer is popular in laser diode driver applications and certain telecommunications equipment levelsetting applications. These applications are sometimes operated between ground and a negative supply voltage such that the systems can be biased at ground to avoid large bypass capacitors that may significantly impede the ac performance. Like most digital potentiometers, the AD5280/AD5282 can be configured with a negative supply (see Figure 50). TERMINAL VOLTAGE OPERATING RANGE The AD5280/AD5282 positive VDD and negative VSS power supply defines the boundary conditions for proper 3-terminal digital potentiometer operation. Supply signals present on Resistor Terminal A, Resistor Terminal B, and Wiper Terminal W that exceed VDD or VSS are clamped by the internal forwardbiased diodes (see Figure 53). A W B VSS GND LEVEL SHIFTED SDA LEVEL SHIFTED SCL VSS Figure 53. Maximum Terminal Voltages Set by VDD and VSS 02929-049 –5V 02929-053 VDD VDD Figure 50. Biased at Negative Voltage POWER-UP SEQUENCE However, the digital inputs must also be level shifted to allow proper operation because the ground is referenced to the negative potential. Figure 51 shows one implementation with a few transistors and a few resistors. When VIN is below the Q3 threshold value, Q3 is off, Q1 is off, and Q2 is on. In this state, VOUT approaches 0 V. When VIN is above 2 V, Q3 is on, Q1 is on, and Q2 is turned off. In this state, VOUT is pulled down to VSS. Be aware that proper time shifting is also needed for successful communication with the device. Because there are ESD protection diodes that limit the voltage compliance at Terminal A, Terminal B, and Terminal W (see Figure 53), it is important to power VDD/VSS before applying any voltage to the A, B, and W terminals. Otherwise, the diode is forward biased such that VDD/VSS is unintentionally powered, which may affect the rest of the user’s circuit. The ideal powerup sequence is the following: GND, VDD, VSS, digital inputs, and VA/VB/VW. The order of powering VA/VB/VW and digital inputs is not important as long as they are powered after VDD/VSS. Rev. C | Page 18 of 28 AD5280/AD5282 LAYOUT AND POWER SUPPLY BYPASSING VDD Similarly, it is also a good practice to bypass the power supplies with quality capacitors for optimum stability. Supply leads to the device should be bypassed with 0.01 μF to 0.1 μF disc or chip ceramic capacitors. Low ESR 1 μF to 10 μF tantalum or electrolytic capacitors should also be applied at the supplies to minimize any transient disturbance and filter low frequency ripple (see Figure 54). Notice that the digital ground should also be joined remotely to the analog ground at one point to minimize digital ground bounce. Rev. C | Page 19 of 28 C3 10µF + C4 10µF VSS + VDD C1 0.1µF AD5280/ AD5282 C2 0.1µF VSS GND 02929-054 It is a good practice to design a layout with compact, minimum lead lengths. The leads to the input should be as direct as possible with a minimum conductor length. Ground paths should have low resistance and low inductance. Figure 54. Power Supply Bypassing AD5280/AD5282 APPLICATIONS INFORMATION BIPOLAR DC OR AC OPERATION FROM DUAL SUPPLIES The AD5280/AD5282 can be operated from dual supplies enabling control of ground-referenced ac signals or bipolar operation. The ac signal, as high as VDD/VSS, can be applied directly across Terminal A to Terminal B with the output taken from Terminal W. See Figure 55 for a typical circuit connection. +5.0V SCL A1 SDA W1 ±2.5V p-p ±5V p-p B1 D–80 H AD5282 GND Similarly, there are W and A terminal capacitances connected to the output (not shown); fortunately, their effect at this node is less significant and the compensation can be avoided in most cases. A2 W2 15 V, 8-BIT I2C DAC VDD 02929-055 B2 VSS –5.0V VDD RBIAS Figure 55. Bipolar Operation from Dual Supplies U1A GAIN CONTROL COMPENSATION V+ The digital potentiometer is commonly used in gain control applications such as the noninverting gain amplifier shown in Figure 56. B 200kΩ ADR512 AD8512 D1 U2 AD5280 200kΩ V– B A U1B AD8512 VO R2 W R1 02929-057 VDD SCLK MICROCONTROLLER MOSI GND Depending on the op amp GBP, reducing the feedback resistor may extend the zero’s frequency far enough to overcome the problem. A better approach is to include a compensation capacitor C2 to cancel the effect caused by C1. Optimum compensation occurs when R1 × C1 = R2 × C2. This is not an option unless C2 is scaled as if R2 were at its maximum value. Doing so may overcompensate and compromise the performance slightly when R2 is set at low values. However, it avoids the gain peaking, ringing, or oscillation at the worst case. For critical applications, C2 should be found empirically to suit the need. In general, C2 in the range of a few picofarads (pF) to no more than a few tenths of a picofarad is usually adequate for the compensation. C2 4.7pF Figure 57. 8-Bit I2C DAC 47kΩ C1 25pF VI U1 AD5280/AD5282 can be configured as a high voltage DAC, as high as 15 V. The output is VO 02929-056 R1 VO ( D ) = Figure 56. Typical Noninverting Gain Amplifier Notice that the RDAC B terminal parasitic capacitance is connected to the op amp noninverting node. It introduces a 0 for the 1/βO term with 20 dB/decade (dec), whereas a typical op amp GBP has −20 dB/dec characteristics. A large R2 and finite C1 can cause the 0 frequency to fall well below the crossover frequency. Thus the rate of closure becomes 40 dB/dec, and the system has a 0° phase margin at the crossover frequency. The output may ring or oscillate if the input is a rectangular pulse or step function. Similarly, it is also likely to ring when switching between two gain values because this is equivalent to a step change at the input. Rev. C | Page 20 of 28 D R [1.2V × (1 + 2 )] R1 256 (5) AD5280/AD5282 8-BIT BIPOLAR DAC +15V U2 OP2177 W U1 VIN B GND TRIM A R R –15V –5VREF +15V +5VREF VO A2 – ADR425 If R2 is large, a compensation capacitor having a few pF may be needed to avoid any gain peaking. OP2177 + U2 – AD5280 A1 –15V 02929-058 VOUT – Figure 58. 8-Bit Bipolar DAC Figure 58 shows a low cost, 8-bit, bipolar DAC. It offers the same number of adjustable steps but not the precision of conventional DACs. The linearity and temperature coefficients, especially at low value codes, are skewed by the effects of the digital potentiometer wiper resistance. The output of this circuit is 2D VO = ⎛⎜ − 1⎞⎟ × VREF ⎝ 256 ⎠ (6) BIPOLAR PROGRAMMABLE GAIN AMPLIFIER VDD + W2 A2 A1 V1 AD5282 + V+ VDD VO V– A2 B1 W1 U1 – D R1 = ∞, R2 = 0 R1 = R2 R2 = 9R1 0 64 128 192 255 −1 −0.5 0 0.5 0.968 −2 −1 0 1 1.937 −10 −5 0 5 9.680 PROGRAMMABLE VOLTAGE SOURCE WITH BOOSTED OUTPUT OP2177 B2 Table 7. Result of Bipolar Gain Amplifier C1 For applications that require high current adjustments, such as a laser diode driver or tunable laser, a boosted voltage source can be considered (see Figure 60). R2 VS8 A2 –kVI R1 VI 5V V+ VO N1 OP2177 – A1 V– VS8 02929-059 U2 AD5282 Table 7 shows the result of adjusting D, with A2 configured as a unity gain, a gain of 2, and a gain of 10. The result is a bipolar amplifier with linearly programmable gain and a 256-step resolution. U1 Figure 59. Bipolar Programmable Gain Amplifier where K is the ratio of RWB1/RWA1 set by U1. (7) RBIAS IL SIGNAL + B V+ A1 – For applications that require bipolar gain, Figure 59 shows one implementation similar to the previous circuit. The digital potentiometer, U1, sets the adjustment range. The wiper voltage at W2 can therefore be programmed between Vi and –KVi at a given U2 setting. Configuring A2 in noninverting mode allows linear gain and attenuation. The transfer function is VO ⎛ R2 ⎞ ⎛ D2 ⎞ = ⎜1 + × (1 + K ) − K ⎟ ⎟×⎜ Vi ⎝ R1 ⎠ ⎝ 256 ⎠ A W CC LD V– U1 = AD5280 A1 = AD8501, AD8605, AD8541 N1 = FDV301N, 2N7002 02929-060 V1 As in the previous example, in the simpler and more common case where K = 1, a single digital AD5280 potentiometer is used. U1 is replaced by a matched pair of resistors to apply Vi and −Vi at the ends of the digital potentiometer. The relationship becomes R2 ⎞⎛ 2 D2 ⎞ ⎛ (7) VO = ⎜ 1 + − 1⎟ × Vi ⎟⎜ R1 ⎠⎝ 256 ⎝ ⎠ + Figure 60. Programmable Booster Voltage Source In this circuit, the inverting input of the op amp forces the VBIAS to be equal to the wiper voltage set by the digital potentiometer. The load current is then delivered by the supply via the N-channel FET N1. The N1 power handling must be adequate to dissipate (Vi – VO) × IL power. This circuit can source a maximum of 100 mA with a 5 V supply. A1 needs to be a railto-rail input type. For precision applications, a voltage reference such as ADR423, ADR292, or AD1584 can be applied at the input of the digital potentiometer. Rev. C | Page 21 of 28 AD5280/AD5282 PROGRAMMABLE CURRENT SOURCE PROGRAMMABLE BIDIRECTIONAL CURRENT SOURCE +5V SLEEP VOUT 6 REF191 GND 0 TO (2.048 + VL) B C1 1µF +15V W +5V –2.048V TO VL C1 10pF V+ RS 102Ω A 4 AD5280 R2I 15kΩ +5V OP2177 V– +15V A2 A V+ AD5280 OP8510 OP8510 U2 U2 V– 5V W VL RL 100Ω IL V+ OP2177 V– –5V R2B 50kΩ –15V R1 150kΩ A1 R2A 14.95kΩ VL RL 500kΩ –15V |L Figure 61. Programmable Current Source 02929-062 VIN 02929-061 3 R1I 150kΩ U1 2 Figure 62. Programmable Bidirectional Current Source A programmable current source can be implemented with the circuit shown in Figure 61. REF191 is a unique, low supply headroom and high current handling precision reference that can deliver 20 mA at 2.048 V. The load current is simply the voltage across Terminal B to Terminal W of the digital potentiometer divided by RS. IL = VREF × D RS × 2N For applications that require bidirectional current control or higher voltage compliance, a Howland current pump can be a solution (see Figure 62). If the resistors are matched, the load current is (R2 A + R2B ) IL = (8) The circuit is simple, but attention must be paid to two things. First, dual-supply op amps are ideal because the ground potential of REF191 can swing from −2.048 V at zero scale to VL at full scale of the potentiometer setting. Although the circuit works under single supply, the programmable resolution of the system is reduced. For applications that demand higher current capabilities, a few changes to the circuit in Figure 61 produce an adjustable current in the range of hundreds of milliamps. First, the voltage reference needs to be replaced with a high current, low dropout regulator, such as the ADP3333, and the op amp needs to be swapped with a high current dual-supply model, such as the AD8532. Depending on the desired range of current, an appropriate value for RS must be calculated. Because of the high current flowing to the load, the user must pay attention to the load impedance so as not to drive the op amp beyond the positive rail. R1 R2B × VW (9) In theory, R2B can be made as small as needed to achieve the current needed within the A2 output current driving capability. In this circuit, the OP2177 can deliver ±5 mA in either direction, and the voltage compliance approaches 15 V. It can be shown that the output impedance is R1' ×R2B (R1 + R2A ) (10) ZO = R1× R2' − R1' (R2A + R2B ) This output impedance can be infinite if Resistor R1' and Resistor R2' match precisely with R1 and R2A + R2B, respectively. On the other hand, it can be negative if the resistors are not matched. As a result, C1 must be in the range of 1 pF to 10 pF to prevent the oscillation. Rev. C | Page 22 of 28 AD5280/AD5282 PROGRAMMABLE LOW-PASS FILTER 1 ωO = R1R2C1C2 (12) 1 1 + R1C1 R2C2 (13) Q= Users can first select some convenient values for the capacitors. To achieve maximally flat bandwidth where Q = 0.707, let C1 be twice the size of C2 and let R1 = R2. As a result, R1 and R2 can be adjusted to the same settings to achieve the desirable bandwidth. At resonance, setting the following balances the bridge: R2 =2 R1 Once the frequency is set, the oscillation amplitude can be tuned by R2B because 2 (17) VO = I D R2B + V D 3 VO, ID, and VD are interdependent variables. With proper selection of R2B, an equilibrium is reached such that VO converges. R2B can be in series with a discrete resistor to increase the amplitude, but the total resistance cannot be too large to prevent saturation of the output. FREQUENCY ADJUSTMENT C1 CI VP 2.2nF C A B A R2 W R B V+ R 10kΩ A VO W C –2.5V OP1177 U1 ADJUSTED TO SAME SETTING R1 = R1I = R2B = AD5282 D1 = D2 = 1N4148 VN Figure 63. Sallen Key Low-Pass Filter PROGRAMMABLE OSCILLATOR R1 1kΩ In a classic Wien-bridge oscillator (Figure 64), the Wien network (R, R', C, C') provides positive feedback, while R1 and R2 provide negative feedback. At the resonant frequency, fO, the overall phase shift is 0, and the positive feedback causes the circuit to oscillate. With R = R', C = C', and R2 = R2A//(R2B + Rdiode), the oscillation frequency is ωO = 1 1 or f o = RC 2πRC (14) where R is equal to RWA such that R= 256 − D RAB 256 A W +2.5V V+ V– R C2 C 2.2nF AD8601 W RI 10kΩ B +2.5V 02929-063 VI R1 (16) In practice, R2/R1 should be set slightly larger than 2 to ensure that oscillation can start. On the other hand, the alternate turnon of Diode D1 and Diode D2 ensures that R2/R1 are smaller than 2 momentarily and, therefore, stabilizes the oscillation. (15) Rev. C | Page 23 of 28 B U1 VO V– –2.5V R2A R2B 2.1kΩ 10kΩ D1 A D2 B W AMPLITUDE ADJUSTMENT 02929-064 In analog-to-digital conversion applications, it is common to include an antialiasing filter to band-limit the sampling signal. Dual-channel digital potentiometers can be used to construct a second-order Sallen key low-pass filter (see Figure 63). The design equations are VO ωO 2 (11) = ω Vi S 2 + O S + ωO 2 Q Figure 64. Programmable Oscillator with Amplitude Control AD5280/AD5282 RDAC CIRCUIT SIMULATION MODEL MACRO MODEL NET LIST FOR RDAC The internal parasitic capacitances and the external capacitive loads dominate the ac characteristics of the RDACs. Configured as a potentiometer divider, the −3 dB bandwidth of the AD5280 (20 kΩ resistor) measures 310 kHz at half scale. Figure 24 provides the Bode plot characteristics of the three available resistor versions: 20 kΩ, 50 kΩ, and 200 kΩ. A parasitic simulation model is shown in Figure 65. A macro model net list for the 20 kΩ RDAC is provided. .PARAM D=256, RDAC=20E3 * .SUBCKT DPOT (A,W,B) * CA A 0 RWA A W CW W 0 RWB W B CB B 0 * .ENDS DPOT RDAC 20kΩ A B CA 25pF CW 85pF 02929-068 CA 25pF Figure 65. RDAC Circuit Simulation Model for RDAC = 20 kΩ Rev. C | Page 24 of 28 25E-12 {(1-D/256)*RDAC+60} 55E-12 {D/256*RDAC+60} 25E-12 AD5280/AD5282 OUTLINE DIMENSIONS 5.10 5.00 4.90 14 8 4.50 4.40 4.30 6.40 BSC 1 7 PIN 1 0.65 BSC 1.20 MAX 0.15 0.05 COPLANARITY 0.10 0.20 0.09 SEATING PLANE 0.30 0.19 8° 0° 0.75 0.60 0.45 061908-A 1.05 1.00 0.80 COMPLIANT TO JEDEC STANDARDS MO-153-AB-1 Figure 66. 14-Lead Thin Shrink Small Outline Package (TSSOP) (RU-14) Dimensions shown in millimeters 5.10 5.00 4.90 16 9 4.50 4.40 4.30 6.40 BSC 1 8 PIN 1 1.20 MAX 0.15 0.05 0.65 BSC 0.30 0.19 COPLANARITY 0.10 0.20 0.09 SEATING PLANE 8° 0° COMPLIANT TO JEDEC STANDARDS MO-153-AB Figure 67. 16-Lead Thin Shrink Small Outline Package (TSSOP) (RU-16) Dimensions shown in millimeters Rev. C | Page 25 of 28 0.75 0.60 0.45 AD5280/AD5282 ORDERING GUIDE Model 1 AD5280BRU20 AD5280BRU20-REEL7 AD5280BRU50 AD5280BRU50-REEL7 AD5280BRU200-REEL7 AD5280BRUZ20 2 AD5280BRUZ20-REEL72 AD5280BRUZ502 AD5280BRUZ50-REEL72 AD5280BRUZ2002 AD5280BRUZ200-R72 AD5282BRU20 AD5282BRU20-REEL7 AD5282BRU50 AD5282BRU50-REEL7 AD5282BRU200 AD5282BRU200-REEL7 AD5282BRUZ202 AD5282BRUZ20-REEL72 AD5282BRUZ502 AD5282BRUZ50-REEL72 AD5282BRUZ2002 AD5282BRUZ200-R72 AD5282-EVAL 1 2 No. of Channels 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 RAB (kΩ) 20 20 50 50 200 20 20 50 50 200 200 20 20 50 50 200 200 20 20 50 50 200 200 20 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP Evaluation Board Package Option RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 RU-14 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 Line 1 contains model number, Line 2 contains ADI logo followed by the end-to-end resistance value, and Line 3 contains date code YYWW. Z = RoHS Compliant Part. Rev. C | Page 26 of 28 Ordering Quantity 96 1,000 96 1,000 1,000 96 1,000 96 1,000 96 1,000 96 1,000 96 1,000 96 1,000 96 1,000 96 1,000 96 1,000 AD5280/AD5282 NOTES Rev. C | Page 27 of 28 AD5280/AD5282 NOTES ©2002–2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D02929-0-7/09(C) Rev. C | Page 28 of 28