Octal, 16-Bit nanoDAC+
with I2C Interface
AD5675
Data Sheet
FEATURES
GENERAL DESCRIPTION
High performance
High relative accuracy (INL): ±3 LSB maximum at 16 bits
Total unadjusted error (TUE): ±0.14% of FSR maximum
Offset error: ±1.5 mV maximum
Gain error: ±0.06% of FSR maximum
Wide operating ranges
−40°C to +125°C temperature range
2.7 V to 5.5 V power supply
Easy implementation
User selectable gain of 1 or 2 (GAIN pin/bit)
1.8 V logic compatibility
I2C-compatible serial interface
20-lead TSSOP and LFCSP RoHS-compliant packages
The AD5675 is a low power, octal, 16-bit buffered voltage output
digital-to-analog converter (DAC). The device includes a gain
select pin, giving a full-scale output of VREF (gain = 1) or 2 ×
VREF (gain = 2). The device operates from a single 2.7 V to 5.5 V
supply and is guaranteed monotonic by design. The AD5675 is
available in 20-lead TSSOP and LFCSP packages. The power-on
reset circuit and a RSTSEL pin ensure that the output DACs power
up to zero scale or midscale and remain there until a valid write
takes place. The AD5675 contains a power-down mode, reducing
the current consumption to 1 µA typical while in power-down
mode. The AD5675 uses a versatile 2-wire serial interface that
operates at clock rates up to 400 kHz, and includes a VLOGIC pin
intended for 1.62 V to 5.5 V logic.
APPLICATIONS
Table 1. Octal nanoDAC+® Devices
Optical transceivers
Base station power amplifiers
Process control (PLC input/output cards)
Industrial automation
Data acquisition systems
Interface
SPI
Reference
Internal
External
Internal
I2 C
16-Bit
AD5676R
AD5676
AD5675R
12-Bit
AD5672R
Not applicable
AD5671R
FUNCTIONAL BLOCK DIAGRAM
VLOGIC
VDD
VREF
AD5675
DAC
REGISTER
STRING
DAC 0
INPUT
REGISTER
DAC
REGISTER
STRING
DAC 1
INPUT
REGISTER
DAC
REGISTER
STRING
DAC 2
INPUT
REGISTER
DAC
REGISTER
STRING
DAC 3
INPUT
REGISTER
DAC
REGISTER
STRING
DAC 4
A0
INPUT
REGISTER
DAC
REGISTER
STRING
DAC 5
LDAC
INPUT
REGISTER
DAC
REGISTER
STRING
DAC 6
RESET
INPUT
REGISTER
DAC
REGISTER
STRING
DAC 7
SDA
A1
INTERFACE LOGIC
SCL
BUFFER
BUFFER
VOUT1
BUFFER
VOUT2
BUFFER
VOUT3
BUFFER
VOUT4
BUFFER
VOUT5
BUFFER
VOUT6
BUFFER
VOUT 7
GAIN
×1/×2
POWER-ON
RESET
RSTSEL
VOUT0
GAIN
POWER-DOWN
LOGIC
GND
12550-001
INPUT
REGISTER
Figure 1.
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2015–2018 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD5675
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
I2C Slave Address ........................................................................ 20
Applications ....................................................................................... 1
Serial Operation ......................................................................... 20
General Description ......................................................................... 1
Write Operation.......................................................................... 20
Functional Block Diagram .............................................................. 1
Read Operation........................................................................... 21
Revision History ............................................................................... 2
Multiple DAC Readback Sequence .......................................... 21
Specifications..................................................................................... 3
Power-Down Operation ............................................................ 22
AC Characteristics ........................................................................ 5
Load DAC (Hardware LDAC Pin) ........................................... 22
Timing Characteristics ................................................................ 5
LDAC Mask Register ................................................................. 23
Absolute Maximum Ratings ............................................................ 7
Hardware Reset (RESET) .......................................................... 24
Thermal Resistance ...................................................................... 7
Reset Select Pin (RSTSEL) ........................................................ 24
ESD Caution .................................................................................. 7
Software Reset ............................................................................. 24
Pin Configuration and Function Descriptions ............................. 8
Amplifier Gain Selection on LFCSP Package ......................... 24
Typical Performance Characteristics ........................................... 10
Applications Information .............................................................. 25
Terminology .................................................................................... 16
Power Supply Recommendations............................................. 25
Theory of Operation ...................................................................... 18
Microprocessor Interfacing ....................................................... 25
Digital-to-Analog Converter .................................................... 18
AD5675 to ADSP-BF531 Interface ........................................... 25
Transfer Function ....................................................................... 18
Layout Guidelines....................................................................... 25
DAC Architecture ....................................................................... 18
Galvanically Isolated Interface ................................................. 25
Serial Interface ............................................................................ 19
Outline Dimensions ....................................................................... 26
Write and Update Commands .................................................. 20
Ordering Guide .......................................................................... 27
REVISION HISTORY
4/2018—Rev. B to Rev. C
Changes to Features Section, General Description Section, and
Figure 1 .............................................................................................. 1
Changes to Specifications Section .................................................. 3
Changes to VLOGIC Parameter, Table 2 ............................................ 4
Deleted Endnote 3, Table 2; Renumbered Sequentially .............. 4
Changes to AC Characteristics Section, Timing Characteristics
Section, and Table 3 .......................................................................... 5
Changes to Figure 2 and Figure 3 ................................................... 6
Changes to Table 5 and Thermal Resistance Section................... 7
Change to VLOGIC Pin Description, Table 7 .................................... 8
Change to VLOGIC Pin Description, Table 8 .................................... 9
Changes to Figure 19 ...................................................................... 12
Changes to Table 9 .......................................................................... 19
Changes to Update DAC Register n with Contents of Input
Register n Section and Write to and Update DAC Channel n
(Independent of LDAC) Section................................................... 20
Changes to Power-Down Operation Section .............................. 22
Changes to Hardware Reset (RESET) Section ............................ 24
Added Software Reset Section ...................................................... 24
Updated Outline Dimensions ....................................................... 26
Changes to Ordering Guide .......................................................... 27
8/2016—Rev. A to Rev. B
Change to Output Noise Spectral Density Parameter; Table 3 ...5
10/2015—Rev. 0 to Rev. A
Added 20-Lead LFCSP ...................................................... Universal
Changes to Features Section and General Description Section ....1
Changes to Table 2.............................................................................3
Change to Table 5 ..............................................................................7
Added Table 6; Renumbered Sequentially .....................................9
Change to Figure 4 Caption and Table 6 Title ...............................8
Added Figure 5; Renumbered Sequentially and Table 7 ..............9
Change to Figure 19 Caption ........................................................ 12
Change to Figure 33 ....................................................................... 14
Change to Table 8 ........................................................................... 19
Change to Read Operation Section .............................................. 21
Changes to LDAC Mask Register Section and Table 13 ............... 23
Added Amplifier Gain Selection on LFCSP Package Section,
Table 15, and Table 16 .................................................................... 24
Added Figure 52, Outline Dimensions ........................................ 26
Changes to Ordering Guide .......................................................... 26
1/2015—Revision 0: Initial Version
Rev. C | Page 2 of 27
Data Sheet
AD5675
SPECIFICATIONS
VDD = 2.7 V to 5.5 V, 1.62 V ≤ VLOGIC ≤ 5.5 V, resistive load (RL) = 2 kΩ, capacitive load (CL) = 200 pF, all specifications TA = −40°C to
+125°C, unless otherwise noted.
Table 2.
Parameter
STATIC PERFORMANCE 1
Resolution
Relative Accuracy/Integral
Nonlinearity (INL) 2
Min
16
Differential Nonlinearity
(DNL)2
Zero Code Error2
Offset Error2
Full-Scale Error2
Gain Error2
TUE
Offset Error Drift2
DC Power Supply Rejection
Ratio (PSRR)2
DC Crosstalk2
OUTPUT CHARACTERISTICS
Output Voltage Range
Reference Input Impedance
B Grade
Typ
Max
16
Unit
Test Conditions/Comments
±8
±1.8
±3
Bits
LSB
Gain = 1
±1.7
±0.7
±8
±1
±1.7
±0.7
±3
±1
LSB
LSB
Gain = 2
Gain = 1
±0.5
0.8
−0.75
−0.1
−0.018
±1
4
±6
±4
±0.28
±0.5
0.8
−0.75
−0.1
−0.018
±1
1.6
±2
±1.5
±0.14
Gain = 2
Gain = 1 or gain = 2
Gain = 1
Gain = 2
Gain = 1
−0.013
+0.04
−0.02
±0.03
±0.006
±1
0.25
±0.14
±0.24
±0.12
±0.3
±0.25
−0.013
+0.04
−0.02
±0.03
±0.006
±1
0.25
±0.07
±0.12
±0.06
±0.18
±0.14
LSB
mV
mV
mV
% of fullscale
range
(FSR)
% of FSR
% of FSR
% of FSR
% of FSR
% of FSR
µV/°C
mV/V
Due to single channel, full-scale
output change
Due to load current change
Due to powering down (per channel)
±2
±2
µV
±3
±2
±3
±2
µV/mA
µV
VREF
2 × VREF
15
0
0
VREF
2 × VREF
15
Gain = 2
Gain = 1
Gain = 2
Gain = 1
Gain = 2
DAC code = midscale, VDD = 5 V ± 10%
183
183
V
V
mA
nF
nF
kΩ
µV/mA
177
177
µV/mA
40
25
2.5
40
25
2.5
mA
Ω
µs
Exiting power-down mode, VDD = 5 V
398
789
398
789
µA
µA
V
V
kΩ
kΩ
VREF = VDD = VLOGIC = 5.5 V, gain = 1
VREF = VDD = VLOGIC = 5.5 V, gain = 2
Gain = 1
Gain = 2
Gain = 1
Gain = 2
2
10
2
10
1
Short-Circuit Current 4
Load Impedance at Rails 5
Power-Up Time
REFERENCE INPUT
Reference Input Current
Reference Input Range
Min
±1.8
0
0
Output Current Drive (IOUT)
Capacitive Load Stability
Resistive Load 3
Load Regulation
A Grade
Typ
Max
1
1
1
VDD
VDD/2
14
7
1
1
VDD
VDD/2
14
7
Rev. C | Page 3 of 27
Gain = 1
Gain = 2
RL = ∞
RL = 1 kΩ
VDD = 5 V ± 10%, DAC code =
midscale, −30 mA ≤ IOUT ≤ +30 mA
VDD = 3 V ± 10%, DAC code =
midscale, −20 mA ≤ IOUT ≤ +20 mA
AD5675
Parameter
LOGIC INPUTS
Input Current
Input Voltage
Low, VIL
High, VIH
Pin Capacitance
LOGIC OUTPUTS (SDA)
Output Voltage
Low, VOL
High, VOH
Floating State Output
Capacitance
POWER REQUIREMENTS
VLOGIC
VLOGIC Supply Current (ILOGIC)
VDD
VDD Supply Current, IDD
Normal Mode 6
All Power-Down Modes 7
Data Sheet
Min
A Grade
Typ
Max
Min
B Grade
Typ
Max
µA
0.3 ×
VLOGIC
0.3 ×
VLOGIC
V
3
V
3
0.4
VLOGIC −
0.4
pF
0.4
VLOGIC −
0.4
4
4
5.5
3
3
3
3
5.5
5.5
1.1
1.1
1
1
1
1
1
1
Per pin
±1
0.7 ×
VLOGIC
2.7
VREF +
1.5
Test Conditions/Comments
±1
0.7 ×
VLOGIC
1.62
Unit
1.26
1.3
1.7
1.7
2.5
2.5
5.5
5.5
1.62
2.7
VREF +
1.5
1.1
1.1
1
1
1
1
1
1
V
V
ISINK = 200 μA
ISOURCE = 200 μA
pF
5.5
3
3
3
3
5.5
5.5
V
µA
µA
µA
µA
V
V
Power-on, −40°C to +105°C
Power-on, −40°C to +125°C
Power-down, −40°C to +105°C
Power-down, −40°C to +125°C
Gain = 1
Gain = 2
1.26
1.3
1.7
1.7
2.5
2.5
5.5
5.5
mA
mA
µA
µA
µA
µA
µA
µA
VIH = VDD, VIL = GND, VDD = 2.7 V to 5.5 V
−40°C to +85°C
−40°C to +125°C
Tristate to 1 kΩ, −40°C to +85°C
Power-down to 1 kΩ, −40°C to +85°C
Tristate to 1 kΩ, −40°C to +105°C
Power-down to 1 kΩ, −40°C to +105°C
Tristate to 1 kΩ, −40°C to +125°C
Power-down to 1 kΩ, −40°C to +125°C
DC specifications tested with the outputs unloaded, unless otherwise noted. Upper dead band = 10 mV and exists only when VREF = VDD with gain = 1, or when VREF/2 =
VDD with gain = 2. Linearity calculated using a reduced code range of 256 to 65,280.
See the Terminology section.
3
Together, Channel 0, Channel 1, Channel 2, and Channel 3 can source or sink 40 mA. Similarly, together, Channel 4, Channel 5, Channel 6, and Channel 7 can source or
sink 40 mA up to a junction temperature of 125°C.
4
VDD = 5 V. The AD5675 includes current limiting to protect the device during temporary overload conditions. Junction temperature can be exceeded during current
limit. Operation above the specified maximum operation junction temperature can impair device reliability.
5
When drawing a load current at either rail, the output voltage headroom with respect to that rail is limited by the 25 Ω typical channel resistance of the output
devices. For example, when sinking 1 mA, the minimum output voltage = 25 Ω × 1 mA = 25 mV.
6
Interface inactive. All DACs active. DAC outputs unloaded.
7
All DACs powered down.
1
2
Rev. C | Page 4 of 27
Data Sheet
AD5675
AC CHARACTERISTICS
VDD = 2.7 V to 5.5 V, RL = 2 kΩ to GND, CL = 200 pF to GND, 1.62 V ≤ VLOGIC ≤ 5.5 V, all specifications TA = −40°C to +125°C, unless
otherwise noted.
Table 3.
Parameter
Output Voltage Settling Time 1
Slew Rate
Digital-to-Analog Glitch Impulse1
Digital Feedthrough1
Digital Crosstalk1
Analog Crosstalk1
Min
DAC-to-DAC Crosstalk1
Total Harmonic Distortion (THD)1, 2
Output Noise Spectral Density (NSD)1
Output Noise
Signal-to-Noise Ratio (SNR)
Spurious-Free Dynamic Range (SFDR)
Signal-to-Noise-and-Distortion Ratio
(SINAD)
1
2
Typ
5
0.8
1.4
0.13
0.1
−0.25
−1.3
−2.0
−80
80
6
90
83
80
Max
8
Unit
µs
V/µs
nV-sec
nV-sec
nV-sec
nV-sec
nV-sec
nV-sec
dB
nV/√Hz
µV p-p
dB
dB
dB
Test Conditions/Comments
¼ to ¾ scale settling to ±2 LSB
1 LSB change around major carry (gain = 1)
Gain = 1
Gain = 2
Gain = 2
TA = 25°C, bandwidth = 20 kHz, VDD = 5 V, fOUT = 1 kHz
DAC code = midscale, bandwidth = 10 kHz, gain = 1 and 2
0.1 Hz to 10 Hz, gain = 1
TA = 25°C, bandwidth = 20 kHz, VDD = 5 V, fOUT = 1 kHz
TA = 25°C, bandwidth = 20 kHz, VDD = 5 V, fOUT = 1 kHz
TA = 25°C, bandwidth = 20 kHz, VDD = 5 V, fOUT = 1 kHz
See the Terminology section.
Digitally generated sine wave (fOUT) at 1 kHz.
TIMING CHARACTERISTICS
VDD = 2.7 V to 5.5 V, 1.62 V ≤ VLOGIC ≤ 5.5 V, all specifications −40°C to +125°C, unless otherwise noted.
Table 4.
Parameter 1
t1
t2
t3
t4
t5
t6 2
t7
t8
t9
t10 3
t113
t12
t13
t14
t15
tSP 4
C B4
Min
2.5
0.6
1.3
0.6
100
0
0.6
0.6
1.3
0
Max
0.9
300
20 + 0.1CB
20
400
8
10
90
90
0
50
400
Unit
µs
µs
µs
µs
ns
µs
µs
µs
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
pF
Description
SCL cycle time
tHIGH, SCL high time
tLOW, SCL low time
tHD,STA, start/repeated start hold time
tSU,DAT, data setup time
tHD,DAT, data hold time
tSU,STA, repeated start setup time
tSU,STO, stop condition setup time
tBUF, bus free time between a stop condition and a start condition
tR, rise time of SCL and SDA when receiving
tF, fall time of SCL and SDA when transmitting/receiving
LDAC pulse width
SCL rising edge to LDAC rising edge
RESET minimum pulse width low, 1.62 V ≤ VLOGIC ≤ 2.7 V
RESET minimum pulse width low, 2.7 V ≤ VLOGIC ≤ 5.5 V
RESET activation time, 1.62 V ≤ VLOGIC ≤ 2.7 V
RESET activation time, 2.7 V ≤ VLOGIC ≤ 5.5 V
Pulse width of suppressed spike
Capacitive load for each bus line
See Figure 2 and Figure 3.
A master device must provide a hold time of at least 300 ns for the SDA signal (referred to the minimum VIH of the SCL signal) to bridge the undefined region of the
SCL falling edge.
3
tR and tF are measured from 0.3 × VDD to 0.7 × VDD.
4
Input filtering on the SCL and SDA inputs suppresses noise spikes that are less than 50 ns.
1
2
Rev. C | Page 5 of 27
AD5675
Data Sheet
Timing Diagrams
START
CONDITION
REPEATED START
CONDITION
STOP
CONDITION
SDA
t9
t4
t11
t10
t3
SCL
t4
t2
t6
t1
t5
t7
t8
t12
t13
LDAC1
t12
LDAC2
12550-002
NOTES
1ASYNCHRONOUS LDAC UPDATE MODE.
2SYNCHRONOUS LDAC UPDATE MODE.
Figure 2. Two-Wire Serial Interface Timing Diagram
VOUTx
t15
12550-102
RESET
t14
Figure 3. RESET Timing Diagram
Rev. C | Page 6 of 27
Data Sheet
AD5675
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
THERMAL RESISTANCE
Table 5.
Thermal performance is directly linked to printed circuit board
(PCB) design and operating environment. Careful attention to
PCB thermal design is required.
Parameter
VDD to GND
VLOGIC to GND
VOUTx to GND
VREF to GND
Digital Input Voltage to GND
Operating Temperature Range
Storage Temperature Range
Junction Temperature
Reflow Soldering Peak Temperature,
Pb-Free (J-STD-020)
Rating
−0.3 V to +7 V
−0.3 V to +7 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−0.3 V to VLOGIC + 0.3 V
−40°C to +125°C
−65°C to +150°C
125°C
260°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Table 6. Thermal Resistance
Package Type
20-Lead TSSOP
(RU-20)1
20-Lead LFCSP
(CP-20-8)2
θJA
98.65
θJB
44.39
θJC
17.58
ΨJT
1.77
ΨJB
43.9
Unit
°C/W
82
16.67
32.5
0.43
22
°C/W
Thermal impedance simulated values are based on a JEDEC 2S2P thermal
test board. See JEDEC JESD51
2
Thermal impedance simulated values are based on a JEDEC 2S2P thermal
test board with nine thermal vias. See JEDEC JESD51.
1
ESD CAUTION
Rev. C | Page 7 of 27
AD5675
Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
VOUT1
1
20
VOUT0
2
19
VOUT3
VDD
3
18
VREF
VLOGIC
4
17
RESET
SCL
5
16
SDA
A0
6
15
LDAC
A1
7
14
RSTSEL
GAIN
8
13
GND
VOUT7
9
12
VOUT4
VOUT6 10
11
VOUT5
TOP VIEW
(Not to Scale)
12550-006
AD5675
VOUT2
Figure 4. TSSOP Pin Configuration
Table 7. TSSOP Pin Function Descriptions
Pin No.
1
2
3
Mnemonic
VOUT1
VOUT0
VDD
4
5
VLOGIC
SCL
6
7
8
A0
A1
GAIN
9
10
11
12
13
14
VOUT7
VOUT6
VOUT5
VOUT4
GND
RSTSEL
15
LDAC
16
SDA
17
RESET
18
19
20
VREF
VOUT3
VOUT2
Description
Analog Output Voltage from DAC 1. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 0. The output amplifier has rail-to-rail operation.
Power Supply Input. The AD5675 operates from 2.7 V to 5.5 V. Decouple the VDD supply with a 10 µF capacitor in
parallel with a 0.1 µF capacitor to GND.
Digital Power Supply. The voltage on this pin ranges from 1.62 V to 5.5 V.
Serial Clock Line. This pin is used in conjunction with the SDA line to clock data into or out of the 24-bit input shift
register.
Address Input. This pin sets the first LSB of the 7-bit slave address.
Address Input. This pin sets the second LSB of the 7-bit slave address.
Span Set. When this pin is tied to GND, all eight DAC outputs have a span from 0 V to VREF. If this pin is tied to VLOGIC,
all eight DACs output a span of 0 V to 2 × VREF.
Analog Output Voltage from DAC 7. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 6. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 5. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 4. The output amplifier has rail-to-rail operation.
Ground Reference Point for All Circuitry on the Device.
Power-On Reset. Tie this pin to GND to power up all eight DACs to zero scale. Tie this pin to VLOGIC to power up all
eight DACs to midscale.
Load DAC. LDAC operates in two modes, asynchronously and synchronously. Pulsing this pin low allows any or all
DAC registers to be updated if the input registers have new data, which allows all DAC outputs to update
simultaneously. This pin can also be tied permanently low.
Serial Data Input. This pin is used in conjunction with the SCL line to clock data into or out of the 24-bit input shift
register. SDA is a bidirectional, open-drain data line that must be pulled to the supply with an external pull-up resistor.
Asynchronous Reset Input. The RESET input is falling edge sensitive. When RESET is low, all LDAC pulses are ignored.
When RESET is activated, the input register and the DAC register are updated with zero scale or midscale, depending
on the state of the RSTSEL pin.
Reference Input Voltage.
Analog Output Voltage from DAC 3. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 2. The output amplifier has rail-to-rail operation.
Rev. C | Page 8 of 27
AD5675
20
19
18
17
16
VOUT0
VOUT1
VOUT2
VOUT3
NIC
Data Sheet
1
2
3
4
5
AD5675
TOP VIEW
(Not to Scale)
15
14
13
12
11
VREF
RESET
SDA
LDAC
GND
NOTES
1. NIC = NO INTERNAL CONNECTION.
2. EXPOSED PAD. THE EXPOSED PAD
MUST BE TIED TO GND.
12550-005
VOUT7
VOUT6
VOUT5
VOUT4
NIC
6
7
8
9
10
VDD
VLOGIC
SCL
A0
A1
Figure 5. LFCSP Pin Configuration
Table 8. LFCSP Function Descriptions
Pin No.
1
Mnemonic
VDD
2
3
VLOGIC
SCL
4
5
6
7
8
9
10, 16
11
12
A0
A1
VOUT7
VOUT6
VOUT5
VOUT4
NIC
GND
LDAC
13
SDA
14
RESET
15
17
18
19
20
VREF
VOUT3
VOUT2
VOUT1
VOUT0
EPAD
Description
Power Supply Input. The AD5675 operates from 2.7 V to 5.5 V. Decouple the VDD supply with a 10 µF capacitor in
parallel with a 0.1 µF capacitor to GND.
Digital Power Supply. The voltage on this pin ranges from 1.62 V to 5.5 V.
Serial Clock Line. This pin is used in conjunction with the SDA line to clock data into or out of the 24-bit input shift
register.
Address Input. Sets the first LSB of the 7-bit slave address.
Address Input. Sets the second LSB of the 7-bit slave address.
Analog Output Voltage from DAC 7. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 6. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 5. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 4. The output amplifier has rail-to-rail operation.
No Internal Connection.
Ground Reference Point for All Circuitry on the Device.
Load DAC. LDAC operates in two modes, asynchronously and synchronously. Pulsing this pin low allows any or all
DAC registers to be updated if the input registers have new data, which allows all DAC outputs to update
simultaneously. This pin can also be tied permanently low.
Serial Data Input. This pin is used in conjunction with the SCL line to clock data into or out of the 24-bit input shift
register. SDA is a bidirectional, open-drain data line that must be pulled to the supply with an external pull-up resistor.
Asynchronous Reset Input. The RESET input is falling edge sensitive. When RESET is low, all LDAC pulses are ignored.
When RESET is activated, the input register and the DAC register are updated with zero scale or midscale, depending
on the state of the RSTSEL pin.
Reference Input Voltage.
Analog Output Voltage from DAC 3. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 2. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 1. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC 0. The output amplifier has rail-to-rail operation.
Exposed Pad. The exposed pad must be tied to GND.
Rev. C | Page 9 of 27
AD5675
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
2.0
10
8
1.5
6
INL ERROR (LSB)
INL ERROR (LSB)
1.0
0.5
0
–0.5
4
2
0
–2
–4
–1.0
–2.0
10000
20000
30000
40000
50000
60000
70000
CODE
–8
VDD = 5V
TA = 25°C
–10
–40
–20
8
0.6
6
0.4
4
DNL ERROR (LSB)
0.8
0.2
0
–0.2
100
120
100
120
0
–0.6
–6
–0.8
–8
–1.0
50000
80
–2
–4
30000
40000
CODE
60
2
–0.4
60000
70000
–10
–40
12550-009
DNL ERROR (LSB)
10
20000
40
Figure 9. INL Error vs. Temperature
1.0
10000
20
TEMPERATURE (°C)
Figure 6. INL Error vs. Code
0
0
VDD = 5V
TA = 25°C
–20
0
20
40
60
80
TEMPERATURE (°C)
12550-015
0
12550-007
–1.5
12550-013
–6
Figure 10. DNL Error vs. Temperature
Figure 7. DNL Error vs. Code
0.10
0.04
0.09
0.03
0.08
TUE (% OF FSR)
0.01
0
0.06
0.05
0.04
VDD = 5V
TA = 25°C
0.03
0.02
–0.01
0
10000
20000
30000
40000
CODE
50000
60000
70000
0
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 11. TUE vs. Temperature
Figure 8. TUE vs. Code
Rev. C | Page 10 of 27
100
120
12550-017
0.01
–0.02
12550-011
TUE (% OF FSR)
0.07
0.02
AD5675
10
0.10
8
0.08
6
0.06
4
0.04
ERROR (% OF FSR)
2
0
–2
–4
–6
–0.04
3.2
3.7
4.2
4.7
5.2
–0.10
–40
0.10
8
0.08
6
0.06
4
0.04
ERROR (% OF FSR)
DNL ERROR (LSB)
20
40
60
80
100
120
Figure 15. Gain Error and Full-Scale Error vs. Temperature
10
2
0
–2
–4
VDD = 5V
TA = 25°C
0.02
GAIN ERROR
0
–0.02
FULL-SCALE ERROR
–0.04
–0.06
–8
3.7
4.2
4.7
5.2
SUPPLY VOLTAGE (V)
12550-027
–0.08
3.2
0
–20
TEMPERATURE (°C)
Figure 12. INL Error vs. Supply Voltage
–10
2.7
VDD = 5V
TA = 25°C
–0.08
SUPPLY VOLTAGE (V)
–6
GAIN ERROR
–0.02
12550-031
–10
2.7
FULL-SCALE ERROR
0
–0.06
VDD = 5V
TA = 25°C
12550-025
–8
0.02
VDD = 5V
TA = 25°C
–0.10
2.7
3.2
3.7
4.2
4.7
12550-033
INL ERROR (LSB)
Data Sheet
5.2
SUPPLY VOLTAGE (V)
Figure 13. DNL Error vs. Supply Voltage
Figure 16. Gain Error and Full-Scale Error vs. Supply Voltage
0.10
1.8
0.08
1.5
VDD = 5V
TA = 25°C
0.06
1.2
ERROR (mV)
0.02
0
–0.02
ZERO CODE ERROR
0.9
0.6
OFFSET ERROR
0.3
–0.04
0
VDD = 5V
TA = 25°C
–0.3
–0.08
–0.10
2.7
3.2
3.7
4.2
4.7
SUPPLY VOLTAGE (V)
5.2
Figure 14. TUE vs. Supply Voltage
–0.6
–40
–20
0
20
40
60
TEMPERATURE (°C)
80
100
120
Figure 17. Zero Code Error and Offset Error vs. Temperature
Rev. C | Page 11 of 27
12550-035
–0.06
12550-029
TUE (% OF FSR)
0.04
AD5675
Data Sheet
6
1.5
0xFFFF
5
1.0
ZERO CODE ERROR
4
0xC000
0.5
ERROR (mV)
3
VOUT (V)
OFFSET ERROR
0
0x8000
2
0x4000
1
–0.5
0x0000
0
VDD = 5V
TA = 25°C
3.2
4.2
3.7
4.7
–2
–0.06
12550-037
–1.5
2.7
–1
5.2
SUPPLY VOLTAGE (V)
100
0
–0.02
0.02
0.04
0.06
LOAD CURRENT (A)
Figure 18. Zero Code Error and Offset Error vs. Supply Voltage
120
–0.04
12550-042
–1.0
Figure 21. Source and Sink Capability at 5 V
4.0
VDD = 5V
TA = 25°C
REFERENCE = 2.5V
3.5
3.0
VOUT (V)
HITS
0xFFFF
2.5
80
60
2.0
0xC000
1.5
0x8000
1.0
0x4000
40
0.5
0x0000
0
20
0.85
0.87
0.89
0.91
0.93
0.95
0.97
0.99
1.01
IDD FULL SCALE (mA)
–1.0
–0.06
12550-023
0.83
Figure 19. Supply Current (IDD) Histogram
–0.02
0
0.02
LOAD CURRENT (A)
0.04
0.06
Figure 22. Source and Sink Capability at 3 V
1.4
1.6
1.0
SINKING, VDD = –2.7V
SINKING, VDD = –3.0V
SINKING, VDD = –5.0V
SOURCING, VDD = –5.0V
SOURCING, VDD = –3.0V
SOURCING, VDD = –2.7V
0.6
DEVICE 1
DEVICE 2
DEVICE 3
1.5
1.4
IDD (mA)
0.2
–0.2
1.3
1.2
–0.6
–1.4
0
0.005
0.010
0.015
0.020
0.025
0.030
LOAD CURRENT (A)
Figure 20. Headroom/Footroom (ΔVOUT) vs. Load Current
1.0
0
10000
20000
30000
40000
CODE
50000
Figure 23. IDD vs. Code
Rev. C | Page 12 of 27
60000
70000
12550-044
1.1
–1.0
12550-041
ΔVOUT (V)
–0.04
12550-043
–0.5
0
Data Sheet
AD5675
2.0
2.0
1.8
1.8
FULL SCALE
1.6
1.6
DAC 0
DAC 1
DAC 2
DAC 3
DAC 4
DAC 5
DAC 6
DAC 7
1.4
ZERO CODE
1.2
1.0
1.2
VOUT (V)
IDD (mA)
1.4
1.0
0.8
EXTERNAL REFERENCE, FULL SCALE
0.6
0.8
0.4
20
40
60
80
100
TEMPERATURE (°C)
120
VDD = 5.5V
GAIN = 1
1/4 TO 3/4 SCALE
0
80
6
1.8
5
1.6
180
200
0.006
0.005
VDD (V)
VOUT0 (V)
VOUT1 (V)
VOUT2 (V)
VOUT3 (V)
VOUT4 (V)
VOUT5 (V)
VOUT6 (V)
VOUT7 (V)
4
FULL SCALE
VDD (V)
1.4
IDD (mA)
160
Figure 27. Full-Scale Settling Time
2.0
ZERO CODE
3
2
EXTERNAL REFERENCE, FULL SCALE
1.0
140
TIME (µs)
Figure 24. IDD vs. Temperature
1.2
120
100
0.004
0.003
0.002
1
0.001
0
0
VOUT (V)
0
–20
12550-045
0.4
–40
0.2
12550-048
0.6
0.8
3.2
3.7
4.2
4.7
5.2
SUPPLY VOLTAGE (V)
–1
0
2
4
6
–0.001
10
8
12550-049
0.4
2.7
12550-046
0.6
TIME (ms)
Figure 25. IDD vs. Supply Voltage
Figure 28. Power-On Reset to 0 V and Midscale
2.2
3.0
2.0
FULL SCALE
2.0
VOUT (V)
1.4
ZERO CODE
1.2
RESET
1.5
MIDSCALE, GAIN = 1
EXTERNAL REFERENCE, FULL SCALE
1.0
0.8
0.5
0.4
2.7
3.2
3.7
4.2
4.7
INPUT LOGIC VOLTAGE (V)
5.2
Figure 26. IDD vs. Input Logic Voltage
VDD = 5V
TA = 25°C
0
–5
0
5
TIME (µs)
Figure 29. Exiting Power-Down to Midscale
Rev. C | Page 13 of 27
10
12550-050
0.6
12550-047
IDD (mA)
1.6
1.0
MIDSCALE, GAIN = 2
2.5
1.8
AD5675
Data Sheet
0.004
0.003
0.002
1
VOUT (V)
0.001
0
VDD = 5V
GAIN = 1
TA = 25°C
REFERENCE = 2.5V
CODE = 7FFF TO 8000
ENERGY = 1.209376nV-sec
–0.003
–0.004
15
17
16
18
20
19
22
21
TIME (µs)
2
12550-051
–0.002
CH1 5µV
M1.00s
A CH1
401mV
12550-054
–0.001
Figure 33. 0.1 Hz to 10 Hz Output Noise Plot
Figure 30. Digital-to-Analog Glitch Impulse
1200
0.003
VDD = 5V
TA = 25°C
GAIN = 1
FULL SCALE
MIDSCALE
ZERO SCALE
0.002
1000
0.001
800
NSD (nV/√Hz)
VOUT (V)
0
–0.001
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
CHANNEL 5
CHANNEL 6
CHANNEL 7
–0.002
–0.003
–0.004
600
400
200
0
2
4
6
8
10
12
14
16
18
20
TIME (µs)
0
10
12550-052
–0.006
100k
1M
Figure 34. Noise Spectral Density (NSD)
Figure 31. Analog Crosstalk
0.012
0
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
CHANNEL 5
CHANNEL 6
CHANNEL 7
0.010
0.008
0.006
VDD = 5V
TA = 25°C
–20
–40
–60
THD (dBV)
0.004
0.002
0
–0.002
–80
–100
–120
–0.004
–140
–0.006
–0.010
0
2
4
6
8
10
12
14
TIME (µs)
16
18
20
–180
0
2
4
6
8
10
12
14
16
18
FREQUENCY (kHz)
Figure 35. Total Harmonic Distortion (THD) at 1 kHz
Figure 32. DAC-to-DAC Crosstalk
Rev. C | Page 14 of 27
20
12550-056
–160
–0.008
12550-053
VOUT (V)
1k
10k
FREQUENCY (Hz)
100
12550-055
–0.005
Data Sheet
AD5675
2.0
3
0.3
2
0.2
1.9
VOUT (V)
1.6
= 0nF
= 0.1nF
= 1nF
= 4.7nF
= 10nF
VOUT AT MIDSCALE (V)
CL
CL
CL
CL
CL
1.7
1.5
1.4
1.3
RESET
MIDSCALE, GAIN = 1
0.1
1
VOUT AT ZERO SCALE (V)
1.8
1.2
1.1
ZERO SCALE, GAIN = 1
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
0.20
TIME (ms)
0
–20
0
0
60
40
TIME (µs)
Figure 36. Settling Time at Various Capacitive Loads
Figure 38. Hardware Reset
2.0
4.0
1.8
3.5
3.0
1.6
DAC 0
DAC 1
DAC 2
DAC 3
DAC 4
DAC 5
DAC 6
DAC 7
1.0
0.8
2.0
0xC000
1.5
0x8000
1.0
0x4000
0.5
0.4
0
0.2
–0.5
0
80
100
120
140
160
TIME (µs)
180
200
12550-058
0.6
Figure 37. Settling Time, 5.5 V
–1.0
–0.06
0x0000
–0.04
0
–0.02
0.02
LOAD CURRENT (A)
Figure 39. Multiplying Bandwidth
Rev. C | Page 15 of 27
0.04
0.06
12550-043
1.2
0xFFFF
2.5
VOUT (V)
1.4
VOUT (V)
20
12550-059
0.11
12550-057
1.0
0.10
AD5675
Data Sheet
TERMINOLOGY
Relative Accuracy or Integral Nonlinearity (INL)
For a DAC, relative accuracy or integral nonlinearity is a
measurement of the maximum deviation, in LSBs, from a
straight line passing through the endpoints of the DAC transfer
function.
Differential Nonlinearity (DNL)
DNL is the difference between the measured change and the
ideal 1 LSB change between any two adjacent codes. A specified
DNL of ±1 LSB maximum ensures monotonicity. This DAC is
guaranteed monotonic by design.
Zero Code Error
Zero code error is a measurement of the output error when zero
code (0x0000) is loaded to the DAC register. The ideal output is
0 V. The zero code error is always positive because the output of
the DAC cannot go below 0 V due to a combination of the offset
errors in the DAC and the output amplifier. Zero code error is
expressed in mV.
Full-Scale Error
Full-scale error is a measurement of the output error when fullscale code (0xFFFF) is loaded to the DAC register. The ideal
output is VDD − 1 LSB. Full-scale error is expressed in percent of
full-scale range (% of FSR).
Gain Error
Gain error is a measure of the span error of a DAC. It is the
deviation in slope of the DAC transfer characteristic from the
ideal expressed as % of FSR.
Offset Error Drift
Offset error drift is a measurement of the change in offset error
with a change in temperature. It is expressed in µV/°C.
Offset Error
Offset error is a measure of the difference between VOUT (actual)
and VOUT (ideal) expressed in mV in the linear region of the
transfer function. Offset error is measured with Code 256
loaded in the DAC register. It can be negative or positive.
DC Power Supply Rejection Ratio (PSRR)
The dc PSRR indicates how the output of the DAC is affected by
changes in the supply voltage. PSRR is the ratio of the change in
VOUT to the change in VDD for the full-scale output of the DAC.
It is measured in mV/V. VREF is held at 2 V, and VDD is varied by
±10%.
Output Voltage Settling Time
The output voltage settling time is the amount of time it takes
for the output of a DAC to settle to a specified level for a ¼ to ¾
full-scale input change.
Digital-to-Analog Glitch Impulse
Digital-to-analog glitch impulse is the impulse injected into the
analog output when the input code in the DAC register changes
state. It is normally specified as the area of the glitch in nV-sec,
and is measured when the digital input code is changed by
1 LSB at the major carry transition (0x7FFF to 0x8000).
Digital Feedthrough
Digital feedthrough is a measure of the impulse injected into the
analog output of the DAC from the digital inputs of the DAC,
but is measured when the DAC output is not updated. It is
specified in nV-sec, and measured with a full-scale code change
on the data bus, that is, from all 0s to all 1s and vice versa.
Noise Spectral Density (NSD)
NSD is a measurement of the internally generated random
noise. Random noise is characterized as spectral density
(nV/√Hz). To measure NSD, load the DAC to midscale and
measure the noise at the output. It is measured in nV/√Hz.
DC Crosstalk
DC crosstalk is the dc change in the output level of one DAC in
response to a change in the output of another DAC. It is measured
with a full-scale output change on one DAC (or soft power-down
and power-up) while monitoring another DAC kept at midscale.
It is expressed in μV.
DC crosstalk due to load current change is a measure of the
impact that a change in load current on one DAC has on
another DAC kept at midscale. It is expressed in μV/mA.
Digital Crosstalk
Digital crosstalk is the glitch impulse transferred to the output
of one DAC at midscale in response to a full-scale code change
(all 0s to all 1s and vice versa) in the input register of another
DAC. It is measured in standalone mode and is expressed in
nV-sec.
Analog Crosstalk
Analog crosstalk is the glitch impulse transferred to the output
of one DAC due to a change in the output of another DAC. To
measure analog crosstalk, first load one of the input registers
with a full-scale code change (all 0s to all 1s and vice versa).
Then, execute a software LDAC and monitor the output of the
DAC whose digital code was not changed. The area of the glitch
is expressed in nV-sec.
DAC-to-DAC Crosstalk
DAC-to-DAC crosstalk is the glitch impulse transferred to the
output of one DAC due to a digital code change and subsequent
analog output change of another DAC. It is measured by
loading the attack channel with a full-scale code change (all 0s
to all 1s and vice versa), using the write to and update commands
while monitoring the output of the victim channel that is at
midscale. The energy of the glitch is expressed in nV-sec.
Rev. C | Page 16 of 27
Data Sheet
AD5675
Multiplying Bandwidth
The multiplying bandwidth is a measure of the finite bandwidth
of the amplifiers within the DAC. A sine wave on the reference
(with full-scale code loaded to the DAC) appears on the output.
The multiplying bandwidth is the frequency at which the output
amplitude falls to 3 dB below the input.
Total Harmonic Distortion (THD)
THD is the difference between an ideal sine wave and its
attenuated version using the DAC. The sine wave is used as the
reference for the DAC, and the THD is a measurement of the
harmonics present on the DAC output. THD is measured in dB.
Rev. C | Page 17 of 27
AD5675
Data Sheet
THEORY OF OPERATION
DIGITAL-TO-ANALOG CONVERTER
VREF
The AD5675 is an octal, 16-bit, serial input, voltage output DAC.
The AD5675 operates from a supply voltage of 2.7 V to 5.5 V.
Data is written to the AD5675 in a 24-bit word format via a
2-wire serial interface. The AD5675 incorporates a power-on
reset circuit to ensure that the DAC output powers up to a known
output state. The device also has a software power-down mode
that reduces the typical current consumption to 1 µA.
R
R
R
TO OUTPUT
AMPLIFIER
TRANSFER FUNCTION
The gain of the output amplifier is set to ×1 or ×2 using the gain
select pin (GAIN). When the gain select pin is tied to GND, all
eight DAC outputs have a span from 0 V to VREF. When the gain
select pin is tied to VLOGIC, all eight DACs output a span of 0 V to 2
× VREF.
R
12550-067
R
DAC ARCHITECTURE
The AD5675 implements a segmented string DAC architecture
with an internal output buffer. Figure 40 shows the internal
block diagram.
VREF
REF (+)
DAC
REGISTER
RESISTOR
STRING
REF (–)
GND
VOUTx
GAIN
(GAIN = 1 OR 2)
12550-144
INPUT
REGISTER
Figure 40. Single DAC Channel Architecture Block Diagram
The simplified segmented resistor string DAC structure is
shown in Figure 41. The code loaded to the DAC register
determines the node on the string where the voltage is tapped
off and fed into the output amplifier. The voltage is tapped off
by closing one of the switches and connecting the string to the
amplifier. Because each resistance in the string has the same
value, R, the string DAC is guaranteed monotonic.
Figure 41. Resistor String Structure
Output Amplifier
The output buffer amplifier generates rail-to-rail voltages on its
output, which gives an output range of 0 V to VDD. The actual
range depends on the value of VREF, the GAIN pin, the offset
error, and the gain error. The GAIN pin selects the gain of the
output. If the GAIN pin is tied to GND, all eight outputs have a
gain of 1, and the output range is 0 V to VREF. If the GAIN pin is
tied to VLOGIC, all eight outputs have a gain of 2, and the output
range is 0 V to 2 × VREF.
This amplifier can drive a load of 1 kΩ in parallel with 10 nF
to GND. The slew rate is 0.8 V/µs with a typical ¼ to ¾ scale
settling time of 5 µs.
Rev. C | Page 18 of 27
Data Sheet
AD5675
SERIAL INTERFACE
Table 9. Command Definitions
The AD5675 uses a 2-wire, I2C-compatible serial interface. The
device can be connected to an I2C bus as a slave device under
the control of the master devices. The AD5675 supports
standard (100 kHz) and fast (400 kHz) data transfer modes.
Support is not provided for 10-bit addressing and general call
addressing.
C3
0
0
Input Shift Register
The input shift register of the AD5675 is 24 bits wide. Data
is loaded MSB first (DB23), and the first four bits are the
command bits, C3 to C0 (see Table 9), followed by the 4-bit
DAC address bits, A3 to A0 (see Table 10), and finally, the 16bit data-word.
The data-word comprises a 16-bit input code (see Figure 42).
These data bits are transferred to the input register on the
24 falling edges of SCL.
Commands execute on individual DAC channels, combined DAC
channels, or on all DACs, depending on the address bits selected.
Command
C2 C1 C0
0
0
0
0
0
1
0
0
1
0
0
0
0
0
0
1
1
0
1
1
1
1
0
0
1
0
0
1
1
0
0
1
0
1
0
1
0
1
1
0
1
0
1
0
1
1
1
…
1
1
…
1
0
…
1
0
…
1
Description
No operation
Write to Input Register n (where n = 0 to 7,
depending on the DAC selected from the
address bits in Table 10, dependent
on LDAC)
Update DAC Register n with the contents
of Input Register n
Write to and update DAC Channel n
Power down/power up the DAC
Hardware LDAC mask register
Software reset (power-on reset)
Gain setup register (LFCSP package only)
Reserved
Set up the readback register (readback
enable)
Update all channels of the input register
simultaneously with the input data
Update all channels of the DAC register
and input register simultaneously with
the input data
Reserved
Reserved
Table 10. Address Commands
A2
0
0
0
0
1
1
1
1
Channel Address, Bits[3:0]
A1
0
0
1
1
0
0
1
1
A0
0
1
0
1
0
1
0
1
Selected DAC Channel
DAC 0
DAC 1
DAC 2
DAC 3
DAC 4
DAC 5
DAC 6
DAC 7
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
C3
C2
C1
COMMAND
C0
A3
A2
A1
DAC ADDRESS
COMMAND BYTE
A0
D15
D14
D13
D12
D11
D10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
DAC DATA
DAC DATA
DATA HIGH BYTE
DATA LOW BYTE
Figure 42. Input Shift Register Content
Rev. C | Page 19 of 27
12550-302
A3
0
0
0
0
0
0
0
0
AD5675
Data Sheet
WRITE AND UPDATE COMMANDS
SERIAL OPERATION
Write to Input Register n (Dependent on LDAC)
The 2-wire I2C serial bus protocol operates as follows:
Command 0001 allows the user to write to the dedicated input
register of each DAC individually. When LDAC is low, the input
register is transparent, if not controlled by the LDAC mask register.
1.
Update DAC Register n with Contents of Input Register n
2.
Command 0010 loads the DAC registers and outputs with the
contents of the selected input registers and updates the DAC
outputs directly. Data Bit D7 to Bit D0 determine which DACs
have data from the input register transferred to the DAC
register. Setting a bit to 1 transfers data from the input register
to the appropriate DAC register.
3.
Write to and Update DAC Channel n (Independent of LDAC)
Command 0011 allows the user to write to the DAC registers
and updates the DAC outputs directly. The DAC address bits
are used to select the DAC channel.
4.
I2C SLAVE ADDRESS
The AD5675 has a 7-bit I2C slave address. The five MSBs are
00011, and the two LSBs (A1 and A0) are set by the state of the
A1 and A0 address pins. The ability to make hardwired changes to
A1 and A0 allows the user to incorporate up to four AD5675
devices on one bus (see Table 11).
WRITE OPERATION
Table 11. Device Address Selection
A1 Pin Connection
GND
GND
VLOGIC
VLOGIC
A0 Pin Connection
GND
VLOGIC
GND
VLOGIC
A1
0
0
1
1
When writing to the AD5675, begin with a start command
followed by an address byte (R/W = 0), after which the DAC
acknowledges that it is prepared to receive data by pulling SDA
low. The AD5675 require two bytes of data for the DAC, and a
command byte that controls various DAC functions. Three bytes
of data must, therefore, be written to the DAC with the command
byte followed by the most significant data byte and the least
significant data byte, as shown in Figure 43. All these data bytes
are acknowledged by the AD5675. A stop condition follows.
A0
0
1
0
1
1
The master initiates a data transfer by establishing a start
condition when a high to low transition on the SDA line
occurs while SCL is high. The following byte is the address
byte, which consists of the 7-bit slave address.
The slave device with the transmitted address responds by
pulling SDA low during the ninth clock pulse (this is called
the acknowledge bit, or ACK). At this stage, all other
devices on the bus remain idle while the selected device waits
for data to be written to or read from its input shift register.
Data is transmitted over the serial bus in sequences of nine
clock pulses (eight data bits followed by an acknowledge bit).
Transitions on the SDA line must occur during the low period
of SCL; SDA must remain stable during the high period of SCL.
After all data bits are read or written, a stop condition is
established. In write mode, the master pulls the SDA line high
during the 10th clock pulse to establish a stop condition. In
read mode, the master issues a no acknowledge (NACK)
for the ninth clock pulse (that is, the SDA line remains
high). The master then brings the SDA line low before the
10th clock pulse, and then high again during the 10th clock
pulse to establish a stop condition.
9
1
9
SCL
0
SDA
0
0
1
1
A1
A0
DB23
R/W
DB22 DB21 DB20 DB19 DB18
DB17
ACK BY
AD5675
START BY
MASTER
DB16
ACK BY
AD5675
FRAME 1
SLAVE ADDRESS
FRAME 2
COMMAND BYTE
1
9
1
9
SCL
(CONTINUED)
DB15 DB14
DB13 DB12
DB11 DB10
FRAME 3
MOST SIGNIFICANT
DATA BYTE
DB9
DB8
DB7
DB6
ACK BY
AD5675
Figure 43. I2C Write Operation
Rev. C | Page 20 of 27
DB5
DB4
DB3
DB2
FRAME 4
LEAST SIGNIFICANT
DATA BYTE
DB1
DB0
ACK BY
AD5675
STOP BY
MASTER
12550-303
SDA
(CONTINUED)
Data Sheet
AD5675
READ OPERATION
MULTIPLE DAC READBACK SEQUENCE
When reading data back from the AD5675, begin with a start
command followed by an address byte (R/W = 0), after which
the DAC acknowledges that it is prepared to receive data by
pulling SDA low. The address byte must be followed by the
command byte, which determines both the read command that
is to follow and the pointer address to read from; the command
byte is also acknowledged by the DAC. The user configures the
channel to read back the contents of one or more DAC input
registers and sets the readback command to active using the
command byte.
When reading data back from multiple AD5675 DACs, the user
begins with an address byte (R/W = 0), after which the DAC
acknowledges that it is prepared to receive data by pulling SDA
low. The address byte must be followed by the command byte,
which is also acknowledged by the DAC. The user selects the
first channel to read back using the command byte.
Following this sequence, the master establishes a repeated start
condition, and the address is resent with R/W = 1. This byte is
acknowledged by the DAC, indicating that it is prepared to
transmit data. The first two bytes of data are then read from
DAC Input Register n (selected using the command byte), MSB
first, as shown in Figure 44. The next two bytes read back are the
contents of DAC Input Register n + 1, and the next bytes read
back are the contents of DAC Input Register n + 2. Data is read
from the DAC input registers in this auto-incremented fashion
until a NACK followed by a stop condition follows. If the
contents of DAC Input Register 7 are read out, the next two
bytes of data read are the contents of DAC Input Register 0.
Then, the master establishes a repeated start condition, and the
address is resent with R/W = 1. This byte is acknowledged by the
DAC, indicating that it is prepared to transmit data. Two bytes
of data are then read from the DAC, as shown in Figure 44. A
NACK condition from the master, followed by a stop condition,
completes the read sequence. If more than one DAC is selected,
DAC 0 is read back by default.
1
9
1
9
SCL
0
SDA
0
0
1
1
A1
A0
R/W
DB23
DB22
DB21
DB20
DB19
DB18
DB17
DB16
ACK BY
AD5675
START BY
MASTER
ACK BY
AD5675
FRAME 1
SLAVE ADDRESS
FRAME 2
COMMAND BYTE
1
9
1
9
SCL
0
SDA
0
0
REPEATED START BY
MASTER
1
1
A1
A0
R/W
DB15
DB14
DB13
ACK BY
AD5675
FRAME 3
SLAVE ADDRESS
1
DB12
DB11
DB10
DB9
DB8
ACK BY
MASTER
FRAME 4
MOST SIGNIFICANT
DATA BYTE n
9
1
9
SCL
(CONTINUED)
DB7
DB6
DB5
DB4
DB3
DB2
FRAME 5
LEAST SIGNIFICANT
DATA BYTE n
DB1
DB0
DB15
DB14 DB13 DB12
ACK BY
MASTER
Figure 44. I2C Read Operation
Rev. C | Page 21 of 27
DB11 DB10
FRAME 6
MOST SIGNIFICANT
DATA BYTE n + 1
DB9
DB8
NACK BY
MASTER
STOP BY
MASTER
12550-304
SDA
(CONTINUED)
AD5675
Data Sheet
POWER-DOWN OPERATION
The AD5675 contains two separate power-down modes.
Command 0100 is designated for the power-down function (see
Table 9). These power-down modes are software programmable
by setting 16 bits, Bit DB15 to Bit DB0, in the input shift
register. There are two bits associated with each DAC channel.
Table 12 shows how the state of the two bits corresponds to the
mode of operation of the device.
Any or all DACs (DAC 0 to DAC 7) power down to the selected
mode by setting the corresponding bits. See Table 13 for the
contents of the input shift register during the power-down/
power-up operation.
Table 12. Modes of Operation
PD1
0
PD0
0
0
1
1
1
The AD5675 DACs have a double buffered interface consisting
of two banks of registers: input registers and DAC registers.
The user can write to any combination of the input registers.
Updates to the DAC registers are controlled by the LDAC pin.
Instantaneous DAC Updating (LDAC Held Low)
For instantaneous updating of the DACs, LDAC is held low while
data is clocked into the input register using Command 0001. Both
the addressed input register and the DAC register are updated on
the 24th clock, and the output changes immediately.
Deferred DAC Updating (LDAC is Pulsed Low)
When both Bit PD1 and Bit PD0 in the input shift register are
set to 0, the device works normally with its normal power
consumption of typically 1 mA at 5 V. However, for the two
power-down modes, the supply current falls to typically 1 µA.
In addition to this fall, the output stage switches internally from
the amplifier output to a resistor network of known values.
Therefore, the DAC channel output impedance is defined when
the channel is powered down. There are two different powerdown options. The output is connected internally to GND
through either a 1 kΩ resistor, or it is left open circuited
(tristate). The output stage is shown in Figure 45.
AMPLIFIER
DAC
LOAD DAC (HARDWARE LDAC PIN)
For deferred updating of the DACs, LDAC is held high while data
is clocked into the input register using Command 0001. All DAC
outputs are asynchronously updated by pulling LDAC low after the
24th clock. The update occurs on the falling edge of LDAC.
AMPLIFIER
VREF
LDAC
16-BIT
DAC
VOUTx
DAC
REGISTER
INPUT
REGISTER
VOUTx
SCL
SDA
12550-072
Operating Mode
Normal Operation
Power-Down Modes
1 kΩ to GND
Tristate
The bias generator, output amplifier, resistor string, and other
associated linear circuitry shut down when power-down mode
is activated. However, the contents of the DAC registers are
unaffected when in power-down mode. The DAC registers can
be updated while the device is in power-down mode. The time
required to exit power-down is typically 2.5 µs for VDD = 5 V.
INTERFACE
LOGIC
Figure 46. Simplified Diagram of Input Loading Circuitry for a Single DAC
RESISTOR
NETWORK
12550-071
POWER-DOWN
CIRCUITRY
Figure 45. Output Stage During Power-Down
Table 13. 24-Bit Input Shift Register Contents of Power-Down/Power-Up Operation
[DB23:DB20]
0100
1
DB19
0
[DB18:DB16]
XXX1
DAC 7
[DB15:DB14]
[PD1:PD0]
DAC 6
[DB13:DB12]
[PD1:PD0]
DAC 5
[DB11:DB10]
[PD1:PD0]
X means don’t care.
Rev. C | Page 22 of 27
DAC 4
[DB9:DB8]
[PD1:PD0]
DAC 3
[DB7:DB6]
[PD1:PD0]
DAC 2
[DB5:DB4]
[PD1:PD0]
DAC 1
[DB3:DB2]
[PD1:PD0]
DAC 0
[DB1:DB0]
[PD1:PD0]
Data Sheet
AD5675
LDAC MASK REGISTER
Command 0101 is reserved for this hardware LDAC function.
The address bits are ignored. Writing to the DAC using
Command 0101 loads the 8-bit LDAC register (DB7 to DB0).
The default for each channel is 0, that is, the LDAC pin works
normally. Setting the bits to 1 forces this DAC channel to ignore
transitions on the LDAC pin, regardless of the state of the
hardware LDAC pin. This flexibility is useful in applications
where the user wants to select which channels respond to
the LDAC pin.
The LDAC register gives the user extra flexibility and control
over the hardware LDAC pin (see Table 15). Setting the LDAC bits
(DB0 to DB7) to 0 for a DAC channel means that the update for
this channel is controlled by the hardware LDAC pin.
Table 14. LDAC Overwrite Definition
Load LDAC Register
LDAC Bits (DB7 to DB0)
LDAC Pin
LDAC Operation
00000000
11111111
1 or 0
X1
Determined by the LDAC pin.
DAC channels update and override the LDAC pin. DAC channels see LDAC as 1.
1
X means don’t care.
Table 15. Write Commands and LDAC Pin Truth Table 1
Command
0001
Description
Write to Input Register n
(dependent on LDAC)
0010
Update DAC Register n
with the contents of
Input Register n
Write to and update DAC
Channel n
0011
Hardware LDAC Pin State
VLOGIC
GND 2
VLOGIC
GND
Input Register Contents
Data update
Data update
No change
No change
DAC Register Contents
No change (no update)
Data update
Updated with input register contents
Updated with input register contents
VLOGIC
GND
Data update
Data update
Data update
Data update
A high to low hardware LDAC pin transition always updates the contents of the DAC register with the contents of the input register on channels that are not masked
(blocked) by the LDAC mask register.
2
When LDAC is permanently tied low, the LDAC mask bits are ignored.
1
Rev. C | Page 23 of 27
AD5675
Data Sheet
HARDWARE RESET (RESET)
SOFTWARE RESET
The RESET pin is an active low reset that allows the outputs to
be cleared to either zero scale or midscale. The clear code value
is user selectable via the RSTSEL pin. Keep RESET low for a
minimum of 2 µs to complete the operation (see Table 4). When
the RESET signal is returned high, the output remains at the
cleared value until a new value is programmed. While
the RESET pin is low, the outputs cannot be updated with a new
value. Any events on LDAC or RESET during power-on reset
are ignored. If the RESET pin is pulled low at power-up, the
device does not initialize correctly until the pin is released.
A software executable reset function is also available, which
resets the DAC to the power-on reset code. Command 0110 is
designated for this software reset function. The DAC address
bits must be set to 0x0 and the data bits set to 0x1234 for the
software reset command to execute.
RESET SELECT PIN (RSTSEL)
The AD5675 contains a power-on reset circuit that controls the
output voltage during power-up. By connecting the RSTSEL pin
low, the output powers up to zero scale. Note that this power-up
is outside the linear region of the DAC; by connecting the
RSTSEL pin high, the VOUTx pins power up to midscale. The
output remains powered up at this level until a valid write
sequence is made to the DAC.
AMPLIFIER GAIN SELECTION ON LFCSP PACKAGE
The output amplifier gain setting for the LFCSP package is
determined by the state of Bit DB2 in the gain setup register
(see Table 16 and Table 17).
Table 16. Gain Setup Register
Bit
DB2
Description
Amplifier gain setting
DB2 = 0; amplifier gain = 1 (default)
DB2 = 1; amplifier gain = 2
Table 17. 24-Bit Input Shift Register Contents for Gain Setup Command
DB23 (MSB)
0
DB22
1
DB21
1
DB20
1
DB19 to DB3
Don’t care
DB2
Gain
Rev. C | Page 24 of 27
DB1
Reserved; set to 0
DB0 (LSB)
Reserved; set to 0
Data Sheet
AD5675
APPLICATIONS INFORMATION
POWER SUPPLY RECOMMENDATIONS
The AD5675 is typically powered by the following supplies: VDD
= 3.3 V and VLOGIC = 1.8 V.
The ADP7118 can be used to power the VDD pin. The ADP160
can be used to power the VLOGIC pin. This setup is shown in
Figure 47. The ADP7118 can operate from input voltages up to
20 V. The ADP160 can operate from input voltages up to 5.5 V.
ADP7118
3.3V: VDD
LDO
ADP160
1.8V: VLOGIC
LDO
In systems where many devices are on one board, it is often
useful to provide some heat sinking capability to allow the
power to dissipate easily.
The GND plane on the device can be increased (as shown in
Figure 49) to provide a natural heat sinking effect.
12550-176
5V
INPUT
series inductance (ESI), such as the common ceramic types,
which provide a low impedance path to ground at high
frequencies to handle transient currents due to internal logic
switching.
AD5675
Figure 47. Low Noise Power Solution for the AD5675
MICROPROCESSOR INTERFACING
Microprocessor interfacing to the AD5675 is performed via a
serial bus that uses a standard protocol that is compatible with
DSP processors and microcontrollers. The communications
channel requires a 2-wire interface consisting of a clock signal
and a data signal.
BOARD
AD5675 TO ADSP-BF531 INTERFACE
Figure 49. Pad Connection to Board
AD5675
ADSP-BF531
LDAC
RESET
12550-077
PF9
PF8
SCL
SDA
GALVANICALLY ISOLATED INTERFACE
In many process control applications, it is necessary to provide
an isolation barrier between the controller and the unit being
controlled to protect and isolate the controlling circuitry from
any hazardous common-mode voltages that may occur. iCoupler®
products from Analog Devices provide voltage isolation in
excess of 2.5 kV. The serial loading structure of the AD5675
makes the device ideal for isolated interfaces because the
number of interface lines is kept to a minimum. Figure 50
shows a 4-channel isolated interface to the AD5675 using
an ADuM1251. For further information, visit
www.analog.com/icoupler.
CONTROLLER
DECODE
ENCODE
SDA
ENCODE
DECODE
TO SDA
SCL
ENCODE
DECODE
TO SCL
Figure 48. AD5675 to ADSP-BF531 Interface
LAYOUT GUIDELINES
In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to
ensure the rated performance. Design the PCB on which the
AD5675 is mounted so that the device lies on the analog plane.
1ADDITIONAL
The AD5675 must have ample supply bypassing of 10 µF in
parallel with 0.1 µF on each supply, located as close to the package
as possible, ideally right up against the device. The 10 µF
capacitors are the tantalum bead type. The 0.1 µF capacitor
must have low effective series resistance (ESR) and low effective
Rev. C | Page 25 of 27
ADuM12511
PINS OMITTED FOR CLARITY.
Figure 50. Isolated Interface
12550-079
The I2C interface of the AD5675 is designed for easy connection
to industry-standard DSPs and microcontrollers. Figure 48
shows the AD5675 connected to the Analog Devices, Inc.,
Blackfin® processor. The Blackfin processor has an integrated
I2C port that can be connected directly to the I2C pins of the
AD5675.
GPIO1
GPIO2
12550-078
GND
PLANE
AD5675
Data Sheet
OUTLINE DIMENSIONS
6.60
6.50
6.40
20
11
4.50
4.40
4.30
6.40 BSC
1
10
PIN 1
0.65
BSC
1.20 MAX
0.15
0.05
COPLANARITY
0.10
0.30
0.19
0.20
0.09
0.75
0.60
0.45
8°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153-AC
Figure 51. 20-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-20)
Dimensions shown in millimeters
DETAIL A
(JEDEC 95)
0.30
0.25
0.18
16
0.50
BSC
PIN 1
INDIC ATOR AREA OPTIONS
(SEE DETAIL A)
20
1
15
2.75
2.60 SQ
2.35
EXPOSED
PAD
5
11
TOP VIEW
0.80
0.75
0.70
PKG-003502
SEATING
PLANE
SIDE VIEW
0.50
0.40
0.30
10
6
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WGGD-11.
Figure 52. 20-Lead Lead Frame Chip Scale Package [LFCSP]
4 mm × 4 mm Body and 0.75 mm Package Height
(CP-20-8)
Dimensions shown in millimeters
Rev. C | Page 26 of 27
0.20 MIN
10-12-2017-C
PIN 1
INDICATOR
4.10
4.00 SQ
3.90
Data Sheet
AD5675
ORDERING GUIDE
Model 1
AD5675ARUZ
AD5675ARUZ-REEL7
AD5675BRUZ
AD5675BRUZ-REEL7
AD5675ACPZ-REEL7
AD5675ACPZ-RL
AD5675BCPZ-REEL7
AD5675BCPZ-RL
EVAL-AD5675SDZ
1
Resolution
(Bits)
16
16
16
16
16
16
16
16
Temperature
Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Accuracy
±8 LSB INL
±8 LSB INL
±3 LSB INL
±3 LSB INL
±8 LSB INL
±8 LSB INL
±3 LSB INL
±3 LSB INL
Package Description
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Lead Frame Chip Scale Package [LFCSP]
20-Lead Lead Frame Chip Scale Package [LFCSP]
20-Lead Lead Frame Chip Scale Package [LFCSP]
20-Lead Lead Frame Chip Scale Package [LFCSP]
Evaluation Board
Z = RoHS Compliant Part.
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
©2015–2018 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12550-0-4/18(C)
Rev. C | Page 27 of 27
Package
Option
RU-20
RU-20
RU-20
RU-20
CP-20-8
CP-20-8
CP-20-8
CP-20-8
工商网监
湘ICP备2023018690号
