Industrial I/V Output Driver, Single-Supply,
55 V Maximum Supply, Programmable Ranges
AD5751
Data Sheet
FEATURES
GENERAL DESCRIPTION
Current output ranges: 0 mA to 20 mA, 0 mA to 24 mA,
or 4 mA to 20 mA
±0.03% FSR typical total unadjusted error (TUE)
±5 ppm/°C typical output drift
2% overrange
Voltage output ranges: 0 V to 5 V, 0 V to 10 V, 0 V to 40 V
±0.02% FSR typical total unadjusted error (TUE)
±3 ppm/°C typical output drift
Overrange capability on all ranges
Flexible serial digital interface
On-chip output fault detection
PEC error checking
Asynchronous CLEAR function
Power supply range
AVDD: 12 V (± 10%) to 55 V (maximum)
Output loop compliance to AVDD − 2.75 V
Temperature range: −40°C to +105°C
32-lead 5 mm × 5 mm LFCSP package
The AD5751 is a single-channel, low cost, precision, voltage/
current output driver with hardware or software programmable
output ranges. The software ranges are configured via an SPI-/
MICROWIRE™-compatible serial interface. The AD5751
targets applications in PLC and industrial process control. The
analog input to the AD5751 is provided from a low voltage, singlesupply digital-to-analog converter (DAC) and is internally
conditioned to provide the desired output current/voltage
range.
APPLICATIONS
Process control
Actuator control
PLCs
The output current range is programmable across three current
ranges: 0 mA to 20 mA, 0 mA to 24 mA, or 4 mA to 20 mA.
Voltage output is provided from a separate pin that can be
configured to provide 0 V to 5 V, 0 V to 10 V, and 0 V to 40 V
output ranges. An overrange is available on the voltage ranges.
Analog outputs are short-circuit and open-circuit protected and
can drive capacitive loads of 1 μF and inductive loads of 0.1 H.
The device is specified to operate with a power supply range from
10.8 V to 55 V. Output loop compliance is 0 V to AVDD − 2.75 V.
The flexible serial interface is SPI and MICROWIRE
compatible and can be operated in 3-wire mode to minimize
the digital isolation required in isolated applications. The
interface also features an optional PEC error checking feature
using CRC-8 error checking, useful in industrial environments
where data communication corruption can occur.
The device also includes a power-on reset function ensuring
that the device powers up in a known state (0 V or tristate)
and an asynchronous CLEAR pin that sets the outputs to zeroscale/midscale voltage output or the low end of the selected
current range.
An HW SELECT pin is used to configure the part for hardware
or software mode on power-up.
Table 1. Related Device
Part Number
AD5422
Rev. E
Description
Single-channel, 16-bit, serial input current
source and voltage output DAC
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice.
No license is granted by implication or otherwise under any patent or patent rights of Analog
Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2009–2020 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD5751
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
OUTEN........................................................................................ 24
Applications ...................................................................................... 1
Software Control ........................................................................ 24
General Description ......................................................................... 1
Hardware Control ...................................................................... 26
Revision History ............................................................................... 2
Transfer Function ...................................................................... 26
Functional Block Diagram .............................................................. 3
Detailed Description of Features.................................................. 27
Specifications .................................................................................... 4
Output Fault Alert—Software Mode ....................................... 27
Timing Characteristics ................................................................ 7
Output Fault Alert—Hardware Mode .................................... 27
Absolute Maximum Ratings ........................................................... 9
Voltage Output Short-Circuit Protection ............................... 27
ESD Caution.................................................................................. 9
Asynchronous Clear (CLEAR) ................................................. 27
Pin Configuration and Function Descriptions .......................... 10
External Current Setting Resistor ............................................ 27
Typical Performance Characteristics ........................................... 12
Programmable Overrange Modes............................................ 28
Current Output........................................................................... 15
Packet Error Checking .............................................................. 28
Terminology .................................................................................... 20
Applications Information ............................................................. 29
Theory of Operation ...................................................................... 21
Transient Voltage Protection ................................................... 29
Software Mode ............................................................................ 21
Thermal Considerations ........................................................... 29
Currrent Output Architecture .................................................. 23
Layout Guidelines ...................................................................... 30
Driving Inductive Loads ............................................................ 23
Galvanically Isolated Interface ................................................. 30
Power-On State of the AD5751 ................................................ 23
Microprocessor Interfacing ...................................................... 30
Default Registers at Power-On ................................................. 24
Outline Dimensions ....................................................................... 31
Reset Function ............................................................................ 24
Ordering Guide .......................................................................... 31
REVISION HISTORY
9/2020—Rev. D to Rev. E
Changed CP-32-2 to CP-32-7 ...................................... Throughout
Changes to Figure 4........................................................................ 10
Updated Outline Dimensions ....................................................... 31
Changes to Ordering Guide .......................................................... 31
3/2017—Rev. B to Rev. C
Changed CP-32-2 to CP-32-7...................................... Throughout
Changes to Figure 4 ....................................................................... 10
Updated Outline Dimensions ...................................................... 31
Changes to Ordering Guide .......................................................... 31
1/2018—Rev. C to Rev. D
Changed CP-32-7 to CP-32-2 ...................................... Throughout
Changes to Figure 4........................................................................ 10
Updated Outline Dimensions ....................................................... 31
Changes to Ordering Guide .......................................................... 31
10/2013—Rev. A to Rev. B
Changed Thermal Impedance from 28°C/W to 42°C/W
(Throughout) .....................................................................................9
Added Endnote 1 to Table 4 ............................................................9
Changes to Table 12 Calculations ................................................ 29
Updated Outline Dimensions ...................................................... 31
5/2010—Rev. 0 to Rev. A
Changes to Table 2, Power Requirements .....................................6
10/2009—Revision 0: Initial Version
Rev. E | Page 2 of 32
Data Sheet
AD5751
FUNCTIONAL BLOCK DIAGRAM
DVCC GND
AVDD GND COMP1 COMP2
CLEAR
CLRSEL
SCLK/OUTEN*
SDIN/R0*
SYNC/RSET*
SDO/VFAULT*
HW SELECT
VSENSE+
INPUT SHIFT
REGISTER
AND
CONTROL
LOGIC
VOUT RANGE
SCALING
VOUT
VOUT
SHORT FAULT
STATUS
REGISTER
AVDD
VIN
R3
R2
VREF
RESET
IOUT RANGE
SCALING
IOUT
OVERTEMP
NC/IFAULT*
REXT1
VOUT SHORT FAULT
RSET
REXT2
IOUT OPEN FAULT
POWERON RESET
AD5751
AD2/R1*
AD1/R2*
IOUT
OPEN FAULT
AD0/R3*
*DENOTES SHARED PIN. SOFTWARE MODE DENOTED BY REGULAR TEXT, HARDWARE MODE
DENOTED BY ITALIC TEXT. FOR EXAMPLE, FOR FAULT/TEMP PIN, IN SOFTWARE MODE, THIS
PIN TAKES ON FAULT FUNCTION. IN HARDWARE MODE, THIS PIN TAKES ON TEMP FUNCTION.
Figure 1. Functional Block Diagram
Rev. E | Page 3 of 32
07269-001
FAULT/TEMP*
AD5751
Data Sheet
SPECIFICATIONS
AVDD = 12 V (± 10%) to 55 V (maximum), DVCC = 2.7 V to 5.5 V, GND = 0 V. IOUT: RLOAD = 300 Ω. All specifications TMIN to TMAX,
unless otherwise noted.
Table 2.
Parameter1
INPUT VOLTAGE RANGE
Min
Input Leakage Current
REFERENCE INPUT
Reference Input Voltage
−1
Input Leakage Current
VOLTAGE OUTPUT
Output Voltage Ranges
−1
+1
μA
0
0
5
10
V
V
0
0
40
6
V
V
0
0
12
44
V
V
+0.1
+0.05
+0.3
+0.1
+0.02
+14
+5
+4
+3
+2.2
+20
+17
+0.05
+0.04
+0.09
+0.05
% FSR
% FSR
% FSR
% FSR
% FSR
mV
mV
mV
mV
mV
mV
mV
% FSR
% FSR
% FSR
% FSR
ppm FSR/°C
% FSR
% FSR
% FSR
% FSR
ppm FSR/°C
Typ
Max
Unit
+1
V
μA
0 to 4.096
Output Voltage Overranges2
Accuracy
Total Unadjusted Error (TUE)
B Version3
A Version3
Relative Accuracy (INL)
Dead Band on Output, RTI
Offset Error
Gain Error
Gain Error TC4
Full-Scale Error
4.096
−0.1
−0.05
−0.3
−0.1
−0.02
−14
−5
−4
−3
−2.2
−20
−17
−0.05
−0.04
−0.09
−0.05
−0.05
−0.04
−0.09
−0.05
Full-Scale Error TC4
OUTPUT CHARACTERISTICS4
Headroom
Short-Circuit Current
±0.02
±0.05
±0.005
8
±0.5
±0.3
±0.5
±0.015
±0.02
±0.5
±0.015
±0.02
±1.5
V
+0.05
+0.04
+0.09
+0.05
1.3
Test Conditions/Comments
Output unloaded
External reference must be exactly as stated;
otherwise, accuracy errors show up as error
in output
AVDD must have minimum 1.3 V headroom
or >11.3 V
Programmable overranges; see Detailed
Description of Features section
TA = 25°C
TA = 25°C
Referred to 4.096 V input range
0 V to 10 V range
TA = 25°C, 0 V to 10 V range
0 V to 5 V range
TA = 25°C, 0 V to 5 V range
0 V to 40 V range
TA = 25°C, 0 V to 40 V range
0 V to 5 V, 0 V to 10 V range
TA = 25°C
0 V to 40 V range
TA = 25°C
All ranges
0 V to 5 V, 0 V to 10 V range
TA = 25°C
0 V to 40 V range
TA = 25°C
All ranges
V
mA
Output unloaded
1
kΩ
5
kΩ
For specified performance, 0 V to 5 V and 0 V
to 10 V ranges
For specified performance, 0 V to 40 V range
15
Load
Rev. E | Page 4 of 32
Data Sheet
Parameter1
Capacitive Load Stability
RLOAD = ∞
RLOAD = 1 kΩ
RLOAD = ∞
AD5751
Min
Typ
Max
Unit
1
1
2
nF
nF
μF
DC Output Impedance
Settling Time
0 V to 5 V Range, ¼ to ¾ Step
0 V to 5 V Range, 40 mV Input Step
0 V to 40 V Range, ¼ to ¾ Step
Slew Rate
Output Noise
0.12
Ω
7
4.5
15.8
2
3.5
45.5
μs
μs
μs
V/μs
μV rms
μV rms
Output Noise Spectral Density
165
nV/√Hz
AC PSRR
65
dB
10
μV/V
DC PSRR
CURRENT OUTPUT
Output Current Ranges
Output Current Overranges2
ACCURACY (INTERNAL RSET)
Total Unadjusted Error (TUE)
B Version3
A Version3
Relative Accuracy (INL)
Offset Error
Offset Error TC4
Dead Band on Output, RTI
Gain Error
Gain TC4
Full-Scale Error
Full-Scale TC4
ACCURACY (EXTERNAL RSET)
Total Unadjusted Error (TUE)
B Version3
A Version3
Relative Accuracy (INL)
Offset Error
Offset Error TC4
Dead Band on Output, RTI
Gain Error
0
0
3.92
0
0
3.92
−0.2
−0.08
−0.5
−0.3
−0.02
−16
−10
−0.2
−0.125
−0.2
−0.125
−0.1
−0.08
−0.3
−0.1
−0.02
−14
−11
−0.08
−0.07
±0.03
±0.15
±0.01
+5
±3
8
±0.02
±10
±0.02
±4
±0.03
±0.02
±0.01
+5
±2
8
±0.02
24
20
20
24.5
20.4
20.4
mA
mA
mA
mA
mA
mA
+0.2
+0.08
+0.5
+0.3
+0.02
+16
+10
% FSR
% FSR
% FSR
% FSR
% FSR
μa
μa
ppm FSR/°C
mV
% FSR
% FSR
ppm FSR/°C
% FSR
% FSR
ppm FSR/°C
+14
+0.2
+0.125
+0.2
+0.125
+0.1
+0.08
+0.3
+0.1
+0.02
+14
+11
+14
+0.08
+0.07
Rev. E | Page 5 of 32
% FSR
% FSR
% FSR
% FSR
% FSR
μA
Test Conditions/Comments
TA = 25°C
External compensation capacitor required;
see Driving Large Capacitive Loads section
Specified with 2 kΩ || 220 pF, ±0.05%
Specified with 2 kΩ || 220 pF, ±0.05%
Specified with 5 kΩ || 220 pF, ±0.05%
Specified with 1 kΩ || 220 pF
0.1 Hz to 10 Hz bandwidth
100 kHz bandwidth; specified with 2 kΩ ||
220 pF
Measured at 10 kHz; specified with 2 kΩ ||
220 pF
200 mV, 50 Hz/60 Hz sine wave
superimposed on power supply voltage
See Detailed Description of Features section
See Detailed Description of Features section
See Detailed Description of Features section
TA = 25°C
TA = 25°C
TA = 25°C
Referred to 4.096 V input range
TA = 25°C
TA = 25°C
TA = 25°C
TA = 25°C
TA = 25°C
ppm FSR/°C
mV
% FSR
% FSR
Referred to 4.096 V input range
TA = 25°C
AD5751
Parameter1
Gain TC4
Full-Scale Error
Full-Scale TC4
OUTPUT CHARACTERISTICS4
Current Loop Compliance Voltage
Resistive Load
Data Sheet
Min
−0.1
−0.07
VOH, Output High Voltage
SDO
VOL, Output Low Voltage
VOH, Output High Voltage
High Impedance Output
Capacitance
High Impedance Leakage Current
POWER REQUIREMENTS
AVDD
DVCC
Input Voltage
AIDD
DICC
Power Dissipation
Max
+0.1
+0.07
±0.02
±2
0
Inductive Load
Settling Time
4 mA to 20 mA, Full-Scale Step
120 μA Step, 4 mA to 20 mA Range
DC PSRR
Output Impedance
DIGITAL INPUTS4
Input High Voltage, VIH
Input Low Voltage, VIL
Input Current
Pin Capacitance
DIGITAL OUTPUTS4
FAULT, IFAULT, TEMP, VFAULT
VOL, Output Low Voltage
Typ
±1
AVDD − 2.75
See test conditions/comments column
8.5
1.2
Unit
ppm FSR/°C
% FSR
% FSR
ppm FSR/°C
Test Conditions/Comments
TA = 25°C
V
H
Chosen such that compliance is not
exceeded
Needs appropriate capacitor at higher
inductance values; see Driving Inductive
Loads section
130
μs
μs
μA/V
MΩ
5
V
V
μA
pF
Per pin
Per pin
0.6
V
V
V
10 kΩ pull-up resistor to DVCC
At 2.5 mA
10 kΩ pull-up resistor to DVCC
0.5
DVCC − 0.5
3
V
V
pF
Sinking 200 μA
Sourcing 200 μA
1
250 Ω load
250 Ω load
JEDEC compliant
2
0.8
+1
−1
0.4
3.6
0.5
DVCC − 0.5
−1
+1
μA
10.8
55
V
5.5
5.6
6.2
6.2
1
V
mA
mA
mA
mA
mW
2.7
4.4
5.2
5.2
0.3
108
1
Temperature range: −40°C to +105°C; typical at +25°C.
Overranges are nominal; gain and offset are not trimmed as per nominal ranges.
Specification includes gain and offset errors, over temperature, and drift after 1000 hours, TA = 125°C.
4
Guaranteed by characterization, but not production tested.
2
3
Rev. E | Page 6 of 32
Output unloaded, output disabled
Current output enabled
Voltage output enabled
VIH = DVCC, VIL = GND
AVDD = 24 V, outputs unloaded
Data Sheet
AD5751
TIMING CHARACTERISTICS
AVDD = 12 V (± 10%) to 55 V (maximum), DVCC = 2.7 V to 5.5 V, GND = 0 V. VOUT: RLOAD = 2 kΩ (5 kΩ for 0 V to 40 V range),
CL = 200 pF, IOUT: RLOAD = 300 Ω. All specifications TMIN to TMAX, unless otherwise noted.
Table 3.
Parameter1, 2
t1
t2
t3
t4
t5
t6
t7
t8
t9, t10
t11
t12
t13
1
2
Limit at TMIN, TMAX
20
8
8
5
10
5
5
5
1.5
5
40
10
Unit
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
μs max
ns min
ns max
ns min
Description
SCLK cycle time
SCLK high time
SCLK low time
SYNC falling edge to SCLK falling edge setup time
16th SCLK falling edge to SYNC rising edge (on 24th SCLK falling edge if using PEC)
Minimum SYNC high time (write mode)
Data setup time
Data hold time
CLEAR pulse low/high activation time
Minimum SYNC high time (read mode)
SCLK rising edge to SDO valid (SDO CL = 15 pF)
RESET pulse low time
Guaranteed by characterization, but not production tested.
All input signals are specified with tR = tF = 5 ns (10% to 90% of DVCC) and timed from a voltage level of 1.2 V.
Timing Diagrams
t1
SCLK
1
2
16
t3
t6
t2
t4
t5
SYNC
t8
t7
SDIN
D15
D0
CLEAR
t10
t9
VOUT
t13
Figure 2. Write Mode Timing Diagram
Rev. E | Page 7 of 32
07269-003
RESET
AD5751
Data Sheet
SCLK
SYNC
SDIN
t11
A2
A1
A0
R=1
0
X
X
X
X
X
X
X
X
X
X
X
SDO
X
X
X
X
X
R3
R2
R1
R0
CLRSEL OUTEN
Figure 3. Readback Mode Timing Diagram
Rev. E | Page 8 of 32
RSET
PEC
ERROR
OVER
TEMP
IOUT
FAULT
VOUT
FAULT
07269-004
t12
Data Sheet
AD5751
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted. Transient currents of up to
100 mA do not cause SCR latch-up.
Table 4.
Parameter
AVDD to GND
DVCC to GND
Digital Inputs to GND
Digital Outputs to GND
VREF to GND
VSENSE+ to GND
VIN to GND
VOUT, IOUT to GND
Operating Temperature Range
Industrial
Storage Temperature Range
Junction Temperature (TJ max)
32-Lead LFCSP Package
θJA Thermal Impedance1
Lead Temperature
Soldering
1
Rating
−0.3 V to +58 V
−0.3 V to +7 V
−0.3 V to DVCC + 0.3 V, or 7 V
(whichever is less)
−0.3 V to DVCC + 0.3 V, or 7 V
(whichever is less)
−0.3 V to +7 V
−0.3 V to AVDD
−0.3 V to +7 V
−0.3 V to AVDD
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the
operational section of this specification is not implied.
Operation beyond the maximum operating conditions for
extended periods may affect product reliability.
ESD CAUTION
−40°C to +105°C
−65°C to +150°C
125°C
42°C/W
JEDEC industry standard
J-STD-020
Simulated data based on a JEDEC 2s2p test board with thermal vias.
Rev. E | Page 9 of 32
AD5751
Data Sheet
32
31
30
29
28
27
26
25
NC/IFAULT
FAULT/TEMP
RESET
HW SELECT
NC
NC
NC
NC
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
AD5751
TOP VIEW
(Not to Scale)
24
23
22
21
20
19
18
17
VSENSE+
VOUT
GND
GND
COMP1
COMP2
IOUT
AVDD
NOTES
1. NC = NO CONNECT. CAN BE TIED TO GND.
2. THE EXPOSED PADDLE IS TIED TO GND.
07269-005
AD2/R1
AD1/R2
AD0/R3
REXT2
REXT1
VREF
VIN
GND
9
10
11
12
13
14
15
16
SDO/VFAULT
CLRSEL
CLEAR
DVCC
GND
SYNC/RSET
SCLK/OUTEN
SDIN/R0
Figure 4. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
Mnemonic
SDO/VFAULT
2
CLRSEL
3
CLEAR
4
5
6
DVCC
GND
SYNC/RSET
7
SCLK/OUTEN
8
SDIN/R0
9
AD2/R1
Description
Serial Data Output (SDO). In software mode, this pin is used to clock data from the input shift register in
readback mode. Data is clocked out on the rising edge of SCLK and is valid on the falling edge of SCLK.
This pin is a CMOS output.
Short-Circuit Fault Alert (VFAULT). In hardware mode, this pin acts as a short-circuit fault alert pin and is
asserted low when a short-circuit error is detected. This pin is an open-drain output and must be
connected to a pull-up resistor.
In hardware or software mode, this pin selects the clear value, either zero-scale or midscale code. In
software mode, this pin is implemented as a logic OR with the internal CLRSEL bit.
Active High Input. Asserting this pin sets the output current/voltage to zero-scale code or midscale code
of range selected (user-selectable). CLEAR is a logic OR with the internal clear bit. See the Asynchronous
Clear (CLEAR) section for more details.
In software mode, during power-up, the CLEAR pin level determines the power-on condition of the
voltage channel, which can be active 0 V or tristate.
Digital Power Supply.
Ground Connection.
Positive Edge-Sensitive Latch (SYNC). In software mode, a rising edge parallel loads the input shift
register data into the AD5751, also updating the output.
Resistor Select (RSET). In hardware mode, this pin selects whether the internal or the external current
sense resistor is used.
If RSET = 0, the external sense resistor is chosen.
If RSET = 1, the internal sense resistor is chosen.
Serial Clock Input (SCLK). In software mode, data is clocked into the input shift register on the falling
edge of SCLK. This pin operates at clock speeds up to 50 MHz.
Output Enable (OUTEN). In hardware mode, this pin acts as an output enable pin.
Serial Data Input (SDIN). In software mode, data must be valid on the falling edge of SCLK.
Range Decode Bit (R0). In hardware mode, this pin, in conjunction with R1, R2, and R3, selects the output
current/voltage range setting on the part.
Device Addressing Bit (AD2). In software mode, this pin, in conjunction with AD0 and AD1, allows up to
eight devices to be addressed on one bus.
Range Decode Bit (R1). In hardware mode, this pin, in conjunction with R0, R2, and R3, selects the output
current/voltage range setting on the part.
Rev. E | Page 10 of 32
Data Sheet
Pin No.
10
Mnemonic
AD1/R2
11
AD0/R3
12, 13
REXT2, REXT1
14
15
16
17
18
19, 20
VREF
VIN
GND
AVDD
IOUT
COMP2, COMP1
21
22
23
24
25, 26, 27, 28
29
GND
GND
VOUT
VSENSE+
NC
HW SELECT
30
RESET
31
FAULT/TEMP
32
NC/IFAULT
33 (EPAD)
Exposed paddle
AD5751
Description
Device Addressing Bit (AD1). In software mode, this pin, in conjunction with AD0 and AD2, allows up to
eight devices to be addressed on one bus.
Range Decode Bit (R2). In hardware mode, this pin, in conjunction with R0, R1, and R3, selects the output
current/voltage range setting on the part.
Device Addressing Bit (AD0). In software mode, this pin, in conjunction with AD1 and AD2, allows up to
eight devices to be addressed on one bus.
Range Decode Bit (R3). In hardware mode, this pin, in conjunction with R0, R1, and R2, selects the output
current/voltage range setting on the part.
A 15 kΩ external current setting resistor can be connected between the REXT1 and REXT2 pins to
improve the IOUT temperature drift performance.
Buffered Reference Input.
Buffered Analog Input (0 V to 4.096 V).
Ground Connection.
Positive Analog Supply.
Current Output.
Optional Compensation Capacitor Connections for the Voltage Output Buffer. These are used to drive
higher capacitive loads on the output. These pins also reduce overshoot on the output. Care should be
taken when choosing the value of the capacitor connected between the COMP1 and COMP2 pins
because it has a direct influence on the settling time of the output. See the Driving Large Capacitive
Loads section for further details.
Ground Connection.
Ground Connection.
Buffered Analog Output Voltage.
Sense Connection for the Positive Voltage Output Load Connection.
No Connect. Can be tied to GND.
This part is used to configure the part to hardware or software mode.
HW SELECT = 0 selects software control.
HW SELECT = 1 selects hardware control.
In software mode, this pin resets the part to its power-on state. Active low.
In hardware mode, there is no reset. If using the part in hardware mode, the RESET pin should be tied
high.
Fault Alert (FAULT). In software mode, this pin acts as a general fault alert pin. It is asserted low when an
open-circuit, short-circuit, overtemperature error, or PEC interface error is detected. This pin is an opendrain output and must be connected to a pull-up resistor.
Overtemperature Fault (TEMP). In hardware mode, this pin acts as an overtemperature fault pin. It is
asserted low when an overtemperature error is detected. This pin is an open-drain output and must be
connected to a pull-up resistor.
No Connect (NC). In software mode, this pin is a no connect. Instead, tie this pin to GND.
Open-Circuit Fault Alert (IFAULT). In hardware mode, this pin acts as an open-circuit fault alert pin. It is
asserted low when an open-circuit error is detected. This pin is an open-drain output and must be
connected to a pull-up resistor.
The exposed paddle is tied to GND.
Rev. E | Page 11 of 32
AD5751
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
0.10
0.006
0.004
0.002
0
–0.002
–0.004
–0.006
4.096
VIN (V)
0.06
0.04
0
–0.02
–0.04
–0.06
–0.08
–0.10
Figure 5. Integral Nonlinearity Error vs. VIN
105
0V TO 5V RANGE
0V TO 10V RANGE
0V TO 40V RANGE
0.04
FULL-SCALE ERROR (%FSR)
0.006
0.004
0.002
0
–0.002
–0.004
–0.006
0.03
0.02
0.01
0
–0.01
–0.02
–40
25
TEMPERATURE (°C)
105
–0.04
–40
25
TEMPERATURE (°C)
105
07269-018
–0.03
–0.008
–0.010
Figure 9. Full-Scale Error vs. Temperature
Figure 6. Integral Nonlinearity Error vs. Temperature
0.04
0.010
0V TO 5V
0V TO 10V
0V TO 40V
0.008
0V TO 5V RANGE
0V TO 10V RANGE
0V TO 40V RANGE
0.03
0.006
GAIN ERROR (%FSR)
0.02
0.004
0.002
0
–0.002
–0.004
0.01
0
–0.01
–0.02
–0.006
–0.03
4.096
3.803
07269-016
VIN (V)
3.511
3.218
2.926
2.633
2.341
2.048
1.755
1.463
1.170
0.878
0.585
–0.04
0.293
–0.010
–40
25
TEMPERATURE (°C)
Figure 10. Gain Error vs. Temperature
Figure 7. Total Unadjusted Error vs. VIN
Rev. E | Page 12 of 32
105
07269-019
–0.008
0.020
TOTAL UNADJUSTED ERROR (%FSR)
25
TEMPERATURE (°C)
0.05
0V TO 5V RANGE
0V TO 10V RANGE
0V TO 40V RANGE
0.008
–40
Figure 8. Total Unadjusted Error vs. Temperature
07269-015
INTEGRAL NONLINEARITY ERROR (%FSR)
0.010
5V POSITIVE TUE
10V POSITIVE TUE
40V POSITIVE TUE
5V NEGATIVE TUE
10V NEGATIVE TUE
40V NEGATIVE TUE
0.02
07269-014
3.803
3.511
3.218
2.926
2.633
2.341
2.048
1.755
1.463
1.170
0.878
0.585
–0.010
0.293
–0.008
0V TO
0V TO
0V TO
0V TO
0V TO
0V TO
0.08
07269-017
0.008
POSITIVE/NEGATIVE TOTAL UNADJUSTED
ERROR (%FSR)
0V TO 5V
0V TO 10V
0V TO 40V
0.020
INTEGRAL NONLINEARITY ERROR (%FSR)
0.010
Data Sheet
AD5751
1.00
4.0
0V TO 5V RANGE
0V TO 10V RANGE
0V TO 40V RANGE
3.5
0.95
2.5
2.0
HEADROOM (V)
OFFSET ERROR (mV)
3.0
VDD HEADROOM, LOAD OFF
1.5
1.0
0.5
0.90
0.85
0.80
0
–0.5
0.75
–40
25
TEMPERATURE (°C)
105
0.70
07269-020
5V RANGE
0.006
0.005
OUTPUT VOLTAGE DELTA (V)
0.006
0.004
0.002
0
–0.002
–0.004
–0.006
0.004
0.003
0.002
0.001
0
–0.001
–0.008
–0.010
24
48
SUPPLY VOLTAGE (V)
55
–0.002
–15 –13 –11 –9 –7 –5 –3 –1 1 3 5 7
SOURCE/SINK CURRENT (mA)
9
11 13 15
Figure 15. Source and Sink Capability of Output Amplifier
Figure 12. INL Error vs. Supply Voltage
12
0.010
0.008
10
0.006
0.004
8
0V TO 5V POSITIVE TUE
0V TO 10V POSITIVE TUE
0V TO 40V POSITIVE TUE
VOLTAGE (V)
0.002
0
–0.002
–0.004
0V TO 5V NEGATIVE TUE
0V TO 10V NEGATIVE TUE
0V TO 40V NEGATIVE TUE
6
4
–0.006
2
–0.010
24
48
SUPPLY VOLTAGE (V)
55
Figure 13. Total Unadjusted Error vs. Supply Voltage
0
–8
–3
2
7
12
17
22
27
TIME (µs)
Figure 16. Full-Scale Positive Step, 10 V Range
Rev. E | Page 13 of 32
07269-025
–0.008
07269-022
TOTAL UNADJUSTED ERROR (%FSR)
105
0.007
5V LINEARITY, NO LOAD
10V LINEARITY, NO LOAD
40V LINEARITY, NO LOAD
07269-021
INTEGRAL NONLINEARITY ERROR (%FSR)
0.008
25
TEMPERATURE (°C)
Figure 14. AVDD Headroom, 0 V to 10 V Range, Output Set to 10 V, Load Off
Figure 11. Offset Error vs. Temperature
0.010
–40
07269-024
–1.5
07269-023
–1.0
AD5751
Data Sheet
12
10
VOLTAGE (V)
8
6
2
–3
2
7
12
17
22
1s/DIV
07269-026
5µV/DIV
0
–8
07269-029
4
27
TIME (µs)
Figure 20. Peak-to-Peak Noise (0.1 Hz to 10 Hz Bandwidth)
Figure 17. Full-Scale Negative Step, 10 V Range
40
35
30
20
15
10
0
100µV/DIV
–0.5
0
0.5
1.0
1.5
2.0
2.5
TIME (ms)
1s/DIV
07269-027
–5
–1.0
07269-030
5
Figure 18. VOUT vs. Time on Power-Up, Load = 2 kΩ || 200 pF
Figure 21. Peak-to-Peak Noise (100 kHz Bandwidth)
1.0
4.0
3.5
0.8
3.0
VDD
0.6
0.4
2.0
1.5
0.2
1.0
VOUT
2
0
0.5
CH1 5.00V
CH2 20.0mV BW M1.0µs
A CH1
3.00V
0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
TIME (ms)
Figure 19. VOUT Enable Glitch, Load = 2 kΩ || 1 nF
Figure 22. VDD and VOUT vs. Time on Power-Up
Rev. E | Page 14 of 32
–0.2
2.0
07269-031
VDD (V)
2.5
VOUT (V)
1
07269-028
VOUT (mV)
25
Data Sheet
AD5751
CURRENT OUTPUT
0.001
0
–0.001
–0.002
–0.003
0
–0.002
–0.004
–0.006
–0.02
4.096
07269-036
3.803
3.511
3.218
Figure 27. Total Unadjusted Error vs. VIN, External RSET Resistor
0.05
TOTAL UNADJUSTED ERROR (%FSR)
4mA TO 20mA EXTERNAL RSET LINEARITY
0mA TO 20mA EXTERNAL RSET LINEARITY
0mA TO 24mA EXTERNAL RSET LINEARITY
0.006
0.004
0.002
0
–0.002
–0.004
–0.006
4mA TO 20mA INTERNAL RSET TUE
0mA TO 20mA INTERNAL RSET TUE
0mA TO 24mA INTERNAL RSET TUE
0.04
0.03
0.02
0.01
0
–0.01
–0.02
–0.03
Figure 25. Integral Nonlinearity Current Mode, External RSET Sense Resistor
Rev. E | Page 15 of 32
VIN (V)
Figure 28. Total Unadjusted Error vs. VIN, Internal RSET Resistor
07269-037
4.096
3.803
3.511
3.218
2.926
2.633
2.341
2.048
1.755
1.463
1.170
–0.05
0.878
55V
0.585
48V
SUPPLY VOLTAGE (AVDD)
07269-034
24V
0.020
–0.04
–0.008
–0.010
2.926
VIN (V)
Figure 24. Integral Nonlinearity Error vs. VIN, Internal RSET Resistor
0.008
2.633
07269-033
4.096
3.803
3.511
3.218
2.926
2.633
2.341
2.048
1.755
1.463
1.170
0.878
–0.05
0.585
–0.005
0.293
–0.04
0.020
–0.004
2.341
–0.03
2.048
–0.003
1.755
–0.002
–0.01
1.463
–0.001
0
1.170
0
0.01
0.878
0.001
0.02
0.585
0.002
0.03
0.020
TOTAL UNADJUSTED ERROR (%FSR)
0.003
0.010
55V
4mA TO 20mA EXTERNAL RSET TUE
0mA TO 20mA EXTERNAL RSET TUE
0mA TO 24mA EXTERNAL RSET TUE
0.04
0.293
4.096
0.05
VIN (V)
48V
SUPPLY VOLTAGE (AVDD)
Figure 26. Integral Nonlinearity Current Mode, Internal RSET Sense Resistor
4mA TO 20mA INTERNAL RSET RESISTOR
0mA TO 20mA INTERNAL RSET RESISTOR
0mA TO 24mA INTERNAL RSET RESISTOR
0.004
24V
07269-032
3.803
3.511
3.218
2.926
2.633
2.341
2.048
1.755
1.463
1.170
0.878
–0.010
0.585
–0.005
0.293
–0.008
Figure 23. Integral Nonlinearity Error vs. VIN, External RSET Resistor
INTEGRAL NONLINEARITY (%FSR)
0.002
–0.004
VIN (V)
INTEGRAL NONLINEARITY (%FSR)
0.006
0.004
07269-035
INTEGRAL NONLINEARITY (%FSR)
0.002
0.005
4mA TO 20mA INTERNAL RSET LINEARITY
0mA TO 20mA INTERNAL RSET LINEARITY
0mA TO 24mA INTERNAL RSET LINEARITY
0.008
0.003
0.020
INTEGRAL NONLINEARITY (%FSR)
0.010
4mA TO 20mA EXTERNAL RSET RESISTOR
0mA TO 20mA EXTERNAL RSET RESISTOR
0mA TO 24mA EXTERNAL RSET RESISTOR
0.004
0.293
0.005
AD5751
Data Sheet
0.005
4mA TO 20mA EXTERNAL RSET POSITIVE TUE
0mA TO 20mA EXTERNAL RSET POSITIVE TUE
0mA TO 24mA EXTERNAL RSET POSITIVE TUE
0.004
INTEGRAL NONLINEARITY (%FSR)
0.010
0.005
0
–0.005
–0.010
4mA TO 20mA EXTERNAL RSET NEGATIVE TUE
0mA TO 20mA EXTERNAL RSET NEGATIVE TUE
0mA TO 24mA EXTERNAL RSET NEGATIVE TUE
24V
48V
SUPPLY VOLTAGE (AVDD)
55V
POSITIVE/NEGATIVE TUE (%FSR)
0mA TO 24mA INTERNAL
RSET NEGATIVE TUE
4mA TO 20mA INTERNAL
RSET POSITIVE TUE
–0.015
0mA TO 20mA INTERNAL RSET POSITIVE TUE
0mA TO 24mA INTERNAL RSET POSITIVE TUE
24V
48V
SUPPLY VOLTAGE (AVDD)
55V
Figure 30. Total Unadjusted Error Current Mode, Internal RSET Sense Resistor
25
TEMPERATURE (°C)
105
0.04
4mA TO
0mA TO
0mA TO
4mA TO
0mA TO
0mA TO
20mA INTERNAL
20mA INTERNAL
24mA INTERNAL
20mA INTERNAL
20mA INTERNAL
24mA INTERNAL
R SET
R SET
R SET
R SET
R SET
R SET
POSITIVE TUE
POSITIVE TUE
POSITIVE TUE
NEGATIVE TUE
NEGATIVE TUE
NEGATIVE TUE
0.02
0
–0.02
–0.04
–0.06
–40
25
TEMPERATURE (°C)
105
Figure 33. Total Unadjusted Error vs. Temperature, Internal RSET Sense Resistor
0.10
4mA TO 20mA INTERNAL RSET LINEARITY
0mA TO 20mA INTERNAL RSET LINEARITY
0mA TO 24mA INTERNAL RSET LINEARITY
POSITIVE/NEGATIVE TUE (%FSR)
0.08
0.002
0.001
0
–0.001
–0.002
–0.003
0.06
0.04
0.02
0
–0.02
–0.04
–0.06
–0.08
–0.004
–40
25
TEMPERATURE (°C)
105
Figure 31. Integral Nonlinearity Error vs. Temperature,
Internal RSET Sense Resistor
–0.10
07269-040
INTEGRAL NONLINEARITY (%FSR)
0.06
–0.10
0.005
–0.005
–40
–0.08
07269-039
TOTAL UNADJUSTED ERROR (%FSR)
0.10
–0.010
0.003
–0.003
0.08
–0.005
0.004
–0.002
Figure 32. Integral Nonlinearity Error vs. Temperature,
External RSET Sense Resistor
4mA TO 20mA INTERNAL RSET NEGATIVE TUE
0mA TO 20mA INTERNAL RSET NEGATIVE TUE
0
–0.025
–0.001
–0.005
0.005
–0.020
0
–0.004
Figure 29. Total Unadjusted Error Current Mode, External RSET Sense Resistor
0.010
0.001
4mA TO
0mA TO
0mA TO
4mA TO
0mA TO
0mA TO
–40
20mA EXTERNAL
20mA EXTERNAL
24mA EXTERNAL
20mA EXTERNAL
20mA EXTERNAL
24mA EXTERNAL
RSET
RSET
RSET
RSET
RSET
RSET
25
TEMPERATURE (°C)
POSITIVE TUE
POSITIVE TUE
POSITIVE TUE
NEGATIVE TUE
NEGATIVE TUE
NEGATIVE TUE
105
07269-043
–0.020
0.002
07269-041
–0.015
0.003
4mA TO 20mA EXTERNAL RSET LINEARITY
0mA TO 20mA EXTERNAL RSET LINEARITY
0mA TO 24mA EXTERNAL RSET LINEARITY
07269-042
0.015
07269-038
TOTAL UNADJUSTED ERROR (%FSR)
0.020
Figure 34. Total Unadjusted Error vs. Temperature, External RSET Sense Resistor
Rev. E | Page 16 of 32
Data Sheet
AD5751
50
4
45
3
30
25
20
15
4mA TO 20mA EXTERNAL R SET
0mA TO 20mA EXTERNAL R SET
0mA TO 24mA EXTERNAL R SET
0
–40
25
TEMPERATURE (°C)
105
–1
4mA TO 20mA EXTERNAL RSET
0mA TO 20mA EXTERNAL RSET
0mA TO 24mA EXTERNAL RSET
–2
–3
Figure 35. Zero-Scale Error vs. Temperature, External RSET Sense Resistor
–40
0.05
35
0.04
FULL-SCALE ERROR (%FSR)
40
30
25
20
15
10
5
0
4mA TO 20mA INTERNAL RSET
0mA TO 20mA INTERNAL RSET
0mA TO 24mA INTERNAL RSET
–40
25
TEMPERATURE (°C)
105
4mA TO 20mA EXTERNAL R SET
0mA TO 20mA EXTERNAL R SET
0mA TO 24mA EXTERNAL R SET
0.03
0.02
0.01
0
–0.01
–0.02
–0.03
–0.05
–40
0.10
FULL-SCALE ERROR (%FSR)
–1
4mA TO 20mA INTERNAL RSET
0mA TO 20mA INTERNAL RSET
0mA TO 24mA INTERNAL RSET
–40
25
TEMPERATURE (°C)
0.06
0.04
0.02
0
–0.02
–0.04
–0.06
–0.08
105
–0.10
07269-046
OFFSET ERROR (µA)
2
0
105
4mA TO 20mA INTERNAL R SET
0mA TO 20mA INTERNAL R SET
0mA TO 24mA INTERNAL R SET
0.08
1
25
TEMPERATURE (°C)
Figure 39. Full-Scale Error vs. Temperature, External RSET Sense Resistor
3
–3
105
–0.04
Figure 36. Zero-Scale Error vs. Temperature, Internal RSET Sense Resistor
–2
25
TEMPERATURE (°C)
Figure 38. Offset Error vs. Temperature, External RSET Sense Resistor
07269-045
ZERO-SCALE ERROR (µA)
0
07269-048
5
1
Figure 37. Offset Error vs. Temperature, Internal RSET Sense Resistor
–40
25
TEMPERATURE (°C)
105
07269-049
10
2
07269-047
OFFSET ERROR (µA)
35
07269-044
ZERO-SCALE ERROR (µA)
40
Figure 40. Full-Scale Error vs. Temperature, Internal RSET Sense Resistor
Rev. E | Page 17 of 32
AD5751
Data Sheet
0.08
0.06
0.000010
0.000008
10
0.000006
8
0.04
0.02
0
0.000004
0.000002
6
VDD (V)
IOUT
–0.02
–0.04
–0.000002
–0.000004
2
–0.000006
0
VDD
–40
25
TEMPERATURE (°C)
105
07269-050
–0.08
–2
–10
–0.000010
–8
0
2
4
6
8
10
–2
–4
0.04
–6
0.02
0
–0.02
–8
–10
–12
–0.04
–14
–0.06
–16
–0.08
–40
25
TEMPERATURE (°C)
105
–18
–2
07269-051
–0.10
–2
0
IOUT (µA)
GAIN ERROR (%FSR)
0.06
–4
Figure 44. Output Current vs. Time on VDD Power-Up
4mA TO 20mA INTERNAL R SET
0mA TO 20mA INTERNAL R SET
0mA TO 24mA INTERNAL R SET
0.08
–6
TIME (ms)
Figure 41. Gain Error vs. Temperature, External RSET Sense Resistor
0.10
–0.000008
Figure 42. Gain Error vs. Temperature, Internal RSET Sense Resistor
–1
0
1
2
3
4
5
6
7
8
TIME (µs)
Figure 45. Output Current vs. Time on Output Enable, 0 mA to 20 mA Range
2.10
0.025
2.05
0.020
CURRENT (A)
1.95
1.90
1.85
0.015
0.010
1.80
1.75
0.005
AVDD COMPLIANCE VOLTAGE
–40
25
TEMPERATURE (°C)
105
0
–12
–6
1
8
14
21
28
34
41
48
54
TIME (µs)
Figure 46. 4 mA to 20 mA Output Current Step
Figure 43. Output Compliance vs. Temperature
Tested When IOUT = 10.8 mA, 0 mA to 24 mA Range Selected
Rev. E | Page 18 of 32
61
68
07269-055
1.70
07269-052
COMPLIANCE (V)
2.00
1.65
07269-053
–0.06
–0.10
0
4
07269-054
GAIN ERROR (%FSR)
12
4mA TO 20mA EXTERNAL R SET
0mA TO 20mA EXTERNAL R SET
0mA TO 24mA EXTERNAL R SET
IOUT (A)
0.10
Data Sheet
AD5751
3000
4.10
2500
4.05
4.00
DVCC = 5V
AIDD (mA)
DICC (µA)
2000
1500
3.95
3.90
1000
3.85
500
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
LOGIC LEVEL (V)
5.0
3.75
07269-056
0
Figure 49. AIDD vs. AVDD, IOUT = 0 mA
4.10
4.05
3.95
3.90
3.85
3.80
48
AVDD (V)
55
07269-057
AIDD (mA)
4.00
24
48
AVDD (V)
Figure 47. DICC vs. Logic Input Voltage
3.75
24
Figure 48. AIDD vs. AVDD, VOUT = 0 V
Rev. E | Page 19 of 32
55
07269-058
3.80
DVCC = 3V
AD5751
Data Sheet
TERMINOLOGY
Zero-Scale TC
Zero-scale TC is a measure of the change in zero-scale error
with a change in temperature. Zero-scale error TC is expressed
in ppm FSR/°C.
Total Unadjusted Error (TUE)
TUE is a measure of the output error taking all the various
errors into account: INL error, offset error, gain error, and
output drift over supplies, temperature, and time. TUE is
expressed as a percentage of full-scale range (% FSR).
Relative Accuracy or Integral Nonlinearity (INL)
INL is a measure of the maximum deviation, in % FSR, from a
straight line passing through the endpoints of the output driver
transfer function. A typical INL vs. input voltage plot is shown
in Figure 5.
Full-Scale Error
Full-scale error is the deviation of the actual full-scale analog
output from the ideal full-scale output. Full-scale error is
expressed as a percentage of full-scale range (% FSR).
Full-Scale TC
Full-scale TC is a measure of the change in the full-scale error
with a change in temperature. It is expressed in ppm FSR/°C.
Gain Error
Gain error is a measure of the span error of the output. It is the
deviation in slope of the output transfer characteristic from the
ideal expressed in % FSR. A plot of gain error vs. temperature is
shown in Figure 10.
Offset Error
Offset error is a measurement of the difference between the
actual VOUT and the ideal VOUT expressed in millivolts (mV)
in the linear region of the transfer function. It can be negative
or positive.
Output Voltage Settling Time
Output voltage settling time is the amount of time it takes for
the output to settle to a specified level for a half-scale input change.
Slew Rate
The slew rate of a device is a limitation in the rate of change of
the output voltage. The output slewing speed is usually limited
by the slew rate of the amplifier used at its output. Slew rate is
measured from 10% to 90% of the output signal and is
expressed in V/μs.
Current Loop Voltage Compliance
Current loop voltage compliance is the maximum voltage at the
IOUT pin for which the output current is equal to the
programmed value.
Gain Error TC
Gain error TC is a measure of the change in gain error with
changes in temperature. Gain error TC is expressed in ppm
FSR/°C.
Power-On Glitch Energy
Power-on glitch energy is the impulse injected into the analog
output when the AD5751 is powered on. It is specified as the
area of the glitch in nV-sec.
Zero-Scale Error
Zero-scale error is the deviation of the actual zero-scale analog
output from the ideal zero-scale output. Zero-scale error is
expressed in millivolts (mV).
Power Supply Rejection Ratio (PSRR)
PSRR indicates how the output is affected by changes in the
power supply voltage.
Rev. E | Page 20 of 32
Data Sheet
AD5751
THEORY OF OPERATION
ming the R3 to R0 bits in the control register (see Table 7 and
Table 8).
The AD5751 is a single-channel, low cost, precision, voltage/
current output driver with hardware or software programmable
output ranges. The software ranges are configured via an SPI-/
MICROWIRE-compatible serial interface. The hardware ranges
are programmed using the range pins (R0 to R3). The analog
input to the AD5751 is provided from a low voltage, single-supply
DAC (0 V to 4.096 V), which is internally conditioned to
provide the desired output current/voltage range.
Figure 50 and Figure 51 show a typical configuration of AD5751
in software mode and in hardware mode, respectively, in an
output module system. The HW SELECT pin chooses whether
the part is configured in software or hardware mode. The analog
input to the AD5751 is provided from a low voltage, single-supply
DAC such as the AD506x or AD566x, which can provide an
output range of 0 V to 4.096 V. The supply and reference for
the DAC, as well as the reference for the AD5751, can be
supplied from a reference such as the ADR392. The AD5751
can operate with a single supply up to 55 V.
The output current range is programmable across three ranges:
0 mA to 20 mA, 0 mA to 24 mA, or 4 mA to 20 mA. The voltage
output is provided from a separate pin that can be configured to
provide 0 V to 5 V, 0 V to 10 V, and 0 V to 40 V output ranges.
An overrange of 20% is available on the 5 V and 10 V output
voltage ranges, and of 10% on the 0 V to 40 V range. The
VOUT and IOUT pins can be connected together. An overrange of 2% is available on the 0 mA to 20 mA, 0 mA to 24 mA,
and 4 mA to 20 mA current ranges. The current and voltage
outputs are available on separate pins. Only one output can be
enabled at one time. The output range is selected by program-
ADP1720
MCU
SDO
In voltage mode, software-selectable output ranges include 0 V
to 5 V, 0 V to 10 V, 0 V to 40 V.
AVDD
AGND
AVDD
GND
VSENSE+
VREF
REFIN
VIN
AD506x
AD566x
VOUT
RANGE
SCALE
VOUT
0V TO 5V, 0V TO 10V,
0V TO 40V
IOUT
RANGE
SCALE
SYNC1
SCLK
SDIN
SDO
SERIAL
INTERFACE
SYNC
VOUT SHORT FAULT
IOUT OPEN FAULT
OVERTEMP FAULT
IOUT
0mA TO 20mA,
0mA TO 24mA,
4mA TO 20mA
STATUS REGISTER
HW SELECT
FAULT
Figure 50. Typical System Configuration in Software Mode (Pull-Up Resistors Not Shown for Open-Drain Outputs)
Rev. E | Page 21 of 32
07269-006
SDI/DIN
VDD
In current mode, software-selectable output ranges include 0 mA
to 20 mA, 0 mA to 24 mA, or 4 mA to 20 mA.
AD5751
ADR392
SCLK
SOFTWARE MODE
AD5751
Data Sheet
AVDD AGND
ADP1720
AVDD GND
AD5751
ADR392
SCLK
VDD
REFIN
SDI/DIN
MCU
SDO
SYNC1
VSENSE+
VREF
VOUT
RANGE
SCALE
VIN
AD506x
AD566x
VOUT
0V TO 5V, 0V TO 10V,
0V TO 40V
IOUT
RANGE
SCALE
DVCC
IOUT
0mA TO 20mA,
0mA TO 24mA,
4mA TO 20mA
HW SELECT
OUTEN
R3
R2
R1
VFAULT
IFAULT
R0
07269-007
TEMP
OUTPUT RANGE
SELECT PINS
Figure 51. Typical System Configuration in Hardware Mode Using Internal DAC Reference (Pull-Up Resistors Not Shown for Open-Drain Outputs)
Table 6. Suggested Parts for Use with the AD5751
DAC
AD5660
AD5664R
AD5668
AD5060
AD5064/AD5066
AD5662
AD5664
1
2
Reference
Internal
Internal
Internal
ADR434
ADR434
ADR3922
ADR3922
Power
ADP17201
N/A
N/A
ADP1720
N/A
ADR3922
N/A
Resolution/Accuracy
16-bit/12-bit
16-bit/12-bit
16-bit/12-bit
16-bit/16-bit
16-bit/16-bit
16-bit/12-bit
16-bit/12-bit
Description
Mid end system, single channel, internal reference
Mid end system, quad channel, internal reference
Mid end system, octal channel, internal reference
High end system, single channel, external reference
High end system, quad channel, external reference
Mid end system, single channel, external reference
Mid end system, quad channel, external reference
ADP1720 input range up to 28 V.
ADR392 input range up to 15 V.
Rev. E | Page 22 of 32
Data Sheet
AD5751
CURRRENT OUTPUT ARCHITECTURE
The voltage input from the analog input VIN core (0 V to 4.096 V)
is either converted to a current (see Figure 52), which is then
mirrored to the supply rail so that the application simply sees
a current source output with respect to an internal reference
voltage, or it is buffered and scaled to output a software-selectable
unipolar voltage range (see Figure 53). The reference is used to
provide internal offsets for range and gain scaling. The selectable output range is programmable through the digital interface
(software mode) or via the range pins (R0 to R3) (hardware
mode).
AVDD
R2
RANGE DECODE
FROM INTERFACE
R3
T2
T1
VREF
R1
Figure 52. Current Output Configuration
RANGE DECODE
FROM INTERFACE
VSENSE+
VIN
(0V TO 4.096V)
VREF
VOUT RANGE
SCALING
The voltage output amplifier is capable of driving capacitive loads
of up to 1 μF with the addition of a nonpolarized compensation
capacitor between the COMP1 and COMP2 pins.
Without the compensation capacitor, up to 20 nF capacitive loads
can be driven. Care should be taken to choose an appropriate
value for the CCOMP capacitor. This capacitor, while allowing the
AD5751 to drive higher capacitive loads and reduce overshoot,
increases the settling time of the part and therefore affects the
bandwidth of the system. Considered values of this capacitor
should be in the range of 0 nF to 4 nF depending on the trade-off
required between settling time, overshoot, and bandwidth.
On power-up, the AD5751 senses whether hardware or
software mode is loaded and sets the power-up conditions
accordingly.
IOUT
A1
07269-008
VOUT RANGE
SCALING
Driving Large Capacitive Loads
POWER-ON STATE OF THE AD5751
A2
VIN
current and voltage output pins together and configure the end
system as a single-channel output.
VOUT
07269-009
VOUT SHORT FAULT
GND
Figure 53. Voltage Output
DRIVING INDUCTIVE LOADS
When driving inductive or poorly defined loads, connect a 0.01 μF
capacitor between IOUT and GND. This ensures stability with
loads beyond 50 mH. There is no maximum capacitance limit.
The capacitive component of the load may cause slower
settling.
Voltage Output Amplifier
The voltage output amplifier is capable of driving a load of 1
kΩ (for 0 V to 5 V and 0 V to 10 V ranges) and a load of 5 kΩ
(for 0 V to 40 V range) and capacitive loads up to 2 μF (with an
external compensation capacitor on the COMP1 and COMP2
pins). The source and sink capabilities of the output amplifier
can be seen in Figure 15. The slew rate is 2 V/μs.
Internal to the device, there is a 2.5 MΩ resistor connected
between VOUT and VSENSE+. If a fault condition occurs,
these resistors act to protect the AD5751 by ensuring that the
amplifier loop is closed so that the part does not enter into an
open-loop condition.
In software SPI mode, the power-up state of the output is
dependent on the state of the CLEAR pin. If the CLEAR pin is
pulled high, the part powers up, driving an active 0 V on the
output. If the CLEAR pin is pulled low, the part powers up with
the voltage output channel in tristate mode. In both cases, the
current output channel powers up in the tristate condition (0
mA). This allows the voltage and current outputs to be
connected together if desired.
To put the part into normal operation, the user must set the
OUTEN bit in the control register to enable the output and, in
the same write, set the output range configuration using the R3
to R0 range bits. If the CLEAR pin is still high (active) during
this write, the part automatically clears to its normal clear state
as defined by the programmed range and by the CLRSEL pin or
the CLRSEL bit (see the Asynchronous Clear (CLEAR) section
for more details). The CLEAR pin must be taken low to operate
the part in normal mode.
The CLEAR pin is typically driven directly from a
microcontroller. In cases where the power supply for the AD5751
supply is independent of the microcontroller power supply, the
user can connect a weak pull-up resistor to DVCC or a pull-down
resistor to ground to ensure that the correct power-up condition
is achieved independent of the microcontroller. A 10 kΩ pullup/
pull-down resistor on the CLEAR pin should be sufficient for
most applications.
If hardware mode is selected, the part powers up to the conditions
defined by the R3 to R0 range bits and the status of the OUTEN or
CLEAR pin. It is recommended to keep the output disabled
when powering up the part in hardware mode.
The current and voltage are output on separate pins and cannot
be output simultaneously. This allows the user to tie both the
Rev. E | Page 23 of 32
AD5751
Data Sheet
disabled, both the current and voltage channels go into tristate.
The user must set the OUTEN bit to enable the output and
simultaneously set the output range configuration.
DEFAULT REGISTERS AT POWER-ON
The AD5751 power-on-reset circuit ensures that all registers
are loaded with zero code.
In hardware mode, the output can be enabled or disabled using
the OUTEN pin. When the output is disabled, both the current
and voltage channels go into tristate. The user must write to the
OUTEN pin to enable the output. It is recommended that the
output be disabled when changing the ranges.
In software SPI mode, the part powers up with all outputs
disabled (OUTEN bit = 0). The user must set the OUTEN bit in
the control register to enable the output and, in the same write,
set the output range configuration using the R3 to R0 bits.
If hardware mode is selected, the part powers up to the
conditions defined by the R3 to R0 bits and the status of the
OUTEN pin. It is recommended to keep the output disabled
when powering up the part in hardware mode.
SOFTWARE CONTROL
Software control is enabled by connecting the HW SELECT pin
to ground. In software mode, the AD5751 is controlled over a
versatile 3-wire serial interface that operates at clock rates up to
50 MHz. It is compatible with SPI, QSPI™, MICROWIRE, and
DSP standards.
RESET FUNCTION
In software mode, the part can be reset using the RESET pin
(active low) or the reset bit (reset = 1). A reset disables both the
current and voltage outputs to their power-on condition. The
user must write to the OUTEN bit to enable the output and, in
the same write, set the output range configuration. The RESET
pin is a level sensitive input; the part stays in reset mode as long
as the RESET pin is low. The reset bit clears to 0 following a
reset command to the control register.
Input Shift Register
OUTEN
The input shift register is 16 bits wide. Data is loaded into the
device MSB first as a 16-bit word under the control of a serial
clock input, SCLK. Data is clocked in on the falling edge of SCLK.
The input shift register consists of 16 control bits, as shown in
Table 7. The timing diagram for this write operation is shown in
Figure 2. The first three bits of the input shift register are used to
set the hardware address of the AD5751 device on the printed
circuit board (PCB). Up to eight devices can be addressed per
board.
In software mode, the output can be enabled or disabled using
the OUTEN bit in the control register. When the output is
Bit D11, Bit D1, and Bit D0 must always be set to 0 during any
write sequence.
In hardware mode, there is no reset. If using the part in
hardware mode, the RESET pin should be tied high.
Table 7. Input Shift Register Contents for a Write Operation—Control Register
MSB
D15
A2
D14
A1
D13
A0
D12
R/W
D11
0
D10
R3
D9
R2
D8
R1
D7
R0
D6
CLRSEL
D5
OUTEN
D4
Clear
D3
RSET
D2
Reset
D1
0
LSB
D0
0
Table 8. Input Shift Register Descriptions for Control Register
Bit
A2, A1, A0
R/W
Description
Used in association with the AD2, AD1, and AD0 external pins to determine which part is being addressed by the system
controller.
A2
A1
A0
Function
0
0
0
Addresses part with Pin AD2 = 0, Pin AD1 = 0, Pin AD0 = 0.
0
0
1
Addresses part with Pin AD2 = 0, Pin AD1 = 0, Pin AD0 = 1.
0
1
0
Addresses part with Pin AD2 = 0, Pin AD1 = 1, Pin AD0 = 0.
0
1
1
Addresses part with Pin AD2 = 0, Pin AD1 = 1, Pin AD0 = 1.
1
0
0
Addresses part with Pin AD2 = 1, Pin AD1 = 0, Pin AD0 = 0.
1
0
1
Addresses part with Pin AD2 = 1, Pin AD1 = 0, Pin AD0 = 1.
1
1
0
Addresses part with Pin AD2 = 1, Pin AD1 = 1, Pin AD0 = 0.
1
1
1
Addresses part with Pin AD2 = 1, Pin AD1 = 1, Pin AD0 = 1.
Indicates a read from or a write to the addressed register.
Rev. E | Page 24 of 32
Data Sheet
Bit
R3, R2, R1, R0
CLRSEL
OUTEN
Clear
RSET
Reset
AD5751
Description
Selects the output configuration in conjunction with RSET.
RSET
R3
R2
R1
R0
Output Configuration
0
0
0
0
0
4 mA to 20 mA (external 15 kΩ current sense resistor).
0
0
0
0
1
0 mA to 20 mA (external 15 kΩ current sense resistor).
0
0
0
1
0
0 mA to 24 mA (external 15 kΩ current sense resistor).
0
0
0
1
1
Unused command. Do not program.
0
0
1
0
0
Unused command. Do not program.
0
0
1
0
1
0 V to 5 V.
0
0
1
1
0
0 V to 10 V.
0
0
1
1
1
Unused command. Do not program.
0
1
0
0
0
Unused command. Do not program.
0
1
0
0
1
0 V to 6.0 V (20% overrange).
0
1
0
1
0
0 V to 12.0 V (20% overrange).
0
1
0
1
1
Unused command. Do not program.
0
1
1
0
0
Unused command. Do not program.
0
1
1
0
1
Unused command. Do not program.
0
1
1
1
0
0 V to 40 V.
0
1
1
1
1
0 V to 44 V.
1
0
0
0
0
4 mA to 20 mA (internal current sense resistor).
1
0
0
0
1
0 mA to 20 mA (internal current sense resistor).
1
0
0
1
0
0 mA to 24 mA (internal current sense resistor).
1
0
0
1
1
Unused command. Do not program.
1
0
1
0
0
Unused command. Do not program.
1
0
1
0
1
0 V to 5 V.
1
0
1
1
0
0 V to 10 V.
1
0
1
1
1
Unused command. Do not program.
1
1
0
0
0
Unused command. Do not program.
1
1
0
0
1
0 V to 6.0 V (20% overrange).
1
1
0
1
0
0 V to 12.0 V (20% overrange).
1
1
0
1
1
Unused command. Do not program.
1
1
1
0
0
Unused command. Do not program.
1
1
1
0
1
3.92 mA to 20.4 mA (internal current sense resistor).
1
1
1
1
0
0 mA to 20.4 mA (internal current sense resistor).
1
1
1
1
1
0 mA to 24.5 mA (internal current sense resistor).
Sets clear mode to zero scale or midscale. See the Asynchronous Clear (CLEAR) section.
CLRSEL
Function
0
Clear to 0 V.
1
Clear to midscale in unipolar mode; clear to zero scale in bipolar mode.
Output enable bit. This bit must be set to 1 to enable the outputs.
Software clear bit; active high.
Select internal/external current sense resistor.
RSET
Function
1
Select internal current sense resistor; used with R3 to R0 bits to select range.
0
Select external current sense resistor; used with R3 to R0 bits to select range.
Resets the part to its power-on state.
Rev. E | Page 25 of 32
AD5751
Data Sheet
Readback Operation
HARDWARE CONTROL
Readback mode is activated by selecting the correct device address
(A2, A1, A0) and then setting the R/W bit to 1. By default, the
SDO pin is disabled. After having addressed the AD5751 for a
read operation, setting R/W to 1 enables the SDO pin and SDO
data is clocked out on the 5th rising edge of SCLK. After the data
has been clocked out on SDO, a rising edge on SYNC disables
(tristate) the SDO pin again. Status register data (see Table 9)
and control register data are both available during the same
read cycle.
Hardware control is enabled by connecting the HW SELECT
pin to DVCC. In this mode, the R3, R2, R1, and R0 pins, in
conjunction with the RSET pin, are used to configure the
output range, as per Table 8.
The status bits comprise four read-only bits. They are used to
notify the user of specific fault conditions that occur, such as an
open circuit or short circuit on the output, overtemperature
error, or an interface error. If any of these fault conditions
occur, a hardware FAULT is also asserted low, which can be
used as a hardware interrupt to the controller.
See the Detailed Description of Features section for a full
explanation of fault conditions.
In hardware mode, there is no status register. The fault conditions (open circuit, short circuit, and overtemperature) are
available on Pin IFAULT, Pin VFAULT, and Pin TEMP. If any
one of these fault conditions is set, a low is asserted on the
specific fault pin. IFAULT, VFAULT, and TEMP are opendrain outputs and, therefore, can be connected together to
allow the user to generate one interrupt to the system controller
to communicate a fault. If hardwired in this way, it is not
possible to isolate which fault occurred in the system.
TRANSFER FUNCTION
The AD5751 consists of an internal signal conditioning block
that maps the analog input voltage to a programmed output
range. The available analog input range is 0 V to 4.096 V.
For all ranges, both current and voltage, the AD5751 implements a straight linear mapping function, where 0 V maps to
the lower end of the selected range and 4.096 V maps to the
upper end of the selected range.
Table 9. Input Shift Register Contents for a Read Operation—Status Register
MSB
D15
A2
D14
A1
D13
A0
D12
1
D11
0
D10
R3
D9
R2
D8
R1
D7
R0
D6
CLRSEL
D5
OUTEN
D4
RSET
D3
PEC error
D2
OVER TEMP
D1
IOUT fault
LSB
D0
VOUT fault
Table 10. Status Bit Options
Bit
PEC Error
OVER TEMP
IOUT Fault
VOUT Fault
Description
This bit is set if there is an interface error detected by CRC-8 error checking. See the Detailed Description of Features section.
This bit is set if the AD5751 core temperature exceeds approximately 150°C.
This bit is set if there is an open circuit on the IOUT pin.
This bit is set if there is a short circuit on the VOUT pin.
Rev. E | Page 26 of 32
Data Sheet
AD5751
DETAILED DESCRIPTION OF FEATURES
OUTPUT FAULT ALERT—SOFTWARE MODE
In software mode, the AD5751 is equipped with one FAULT
pin; this is an open-drain output allowing several AD5751
devices to be connected together to one pull-up resistor for
global fault detection. In software mode, the FAULT pin is
forced active low by any one of the following fault scenarios:
The voltage at IOUT attempts to rise above the compliance
range due to an open-loop circuit or insufficient power
supply voltage. The internal circuitry that develops the
fault output avoids using a comparator with window limits
because this requires an actual output error before the fault
output becomes active. Instead, the signal is generated
when the internal amplifier in the output stage has less
than approximately 1 V of remaining drive capability.
Thus, the fault output activates slightly before the compliance limit is reached. Because the comparison is made
within the feedback loop of the output amplifier, the
output accuracy is maintained by its open-loop gain, and
an output error does not occur before the fault output
becomes active.
A short is detected on the voltage output pin (VOUT). The
short-circuit current is limited to 15 mA.
An interface error is detected due to the packet error
checking failure (PEC). See the Packet Error Checking
section.
The core temperature of the AD5751 exceeds
approximately 150°C.
OUTPUT FAULT ALERT—HARDWARE MODE
In hardware mode, the AD5751 is equipped with three fault pins:
VFAULT, IFAULT, and TEMP. These are open-drain outputs
allowing several AD5751 devices to be connected together to
one pull-up resistor for global fault detection. In hardware
control mode, these fault pins are forced active by any one of
the following fault scenarios:
An open-circuit is detected. The voltage at IOUT attempts
to rise above the compliance range, due to an open-loop
circuit or insufficient power supply voltage. The internal
circuitry that develops the fault output avoids using a
comparator with window limits because this requires an
actual output error before the fault output becomes active.
Instead, the signal is generated when the internal amplifier
in the output stage has less than approximately 1 V of
remaining drive capability. Thus, the fault output activates
slightly before the compliance limit is reached. Because the
comparison is made within the feedback loop of the output
amplifier, the output accuracy is maintained by its openloop gain, and an output error does not occur before the
fault output becomes active. If this fault is detected, the
IFAULT pin is forced low.
A short is detected on the voltage output pin. The shortcircuit current is limited to 15 mA. If this fault is detected,
the VFAULT pin is forced low.
The core temperature of the AD5751 exceeds approximately 150°C. If this fault is detected, the TEMP pin is
forced low.
VOLTAGE OUTPUT SHORT-CIRCUIT PROTECTION
Under normal operation the voltage output sinks and sources
up to 12 mA and maintains specified operation. The maximum
current that the voltage output delivers is 15 mA; this is the
short-circuit current.
ASYNCHRONOUS CLEAR (CLEAR)
CLEAR is an active high clear that allows the voltage output to
be cleared to either zero-scale code or midscale code, and is
user-selectable via the CLRSEL pin or the CLRSEL bit of the
input shift register, as described in Table 8. (The clear select
feature is a logical OR function of the CLRSEL pin and the
CLRSEL bit). The current loop output clears to the bottom of
its programmed range. When the CLEAR signal is returned
low, the output returns to its programmed value or to a new
programmed value. A clear operation can also be performed via
the clear command in the control register.
Table 11. CLRSEL Options
Output Clear Value
CLRSEL
0
Unipolar Output
Voltage Range
0V
1
Midscale
Unipolar Current Output Range
Zero-scale; for example:
4 mA on the 4 mA to 20 mA range
0 mA on the 0 mA to 20 mA
Midscale; for example:
12 mA on the 4 mA to 20 mA range
10 mA on the 0 mA to 20 mA range
EXTERNAL CURRENT SETTING RESISTOR
Referring to Figure 1, RSET is an internal sense resistor and is
part of the voltage-to-current conversion circuitry. The
nominal value of the internal current sense resistor is 15 kΩ. To
allow for overrange capability in current mode, the user can
also select the internal current sense resistor to be 14.7 kΩ, giving a
nominal 2% overrange capability. This feature is available in the 0
mA to 20 mA, 0 mA to 24 mA, and 4 mA to 20 mA current
ranges.
The stability of the output current value over temperature is
dependent on the stability of the value of RSET. As a method of
improving the stability of the output current over temperature,
an external low drift resistor can be connected to the REXT1
and REXT2 pins of the AD5751, which can be used instead of
the internal resistor. The external resistor is selected via the
input shift register. If the external resistor option is not used,
the REXT1 and REXT2 pins should be left floating.
Rev. E | Page 27 of 32
AD5751
Data Sheet
PROGRAMMABLE OVERRANGE MODES
PACKET ERROR CHECKING
The AD5751 contains an overrange mode for most of the
available ranges. The overranges are selected by configuring the
R3, R1, R1, and R0 bits (or pins) accordingly.
To verify that data has been received correctly in noisy
environments, the AD5751 offers the option of error checking
based on an 8-bit (CRC-8) cyclic redundancy check. The device
controlling the AD5751 should generate an 8-bit frame check
sequence using the following polynomial:
In voltage mode, depending on selected range, the overranges
are 10% or 20%, providing programmable output ranges of 0 V
to 6 V, 0 V to 12 V, and 0 V to 44 V. The 0 V to 4.096 V analog
input remains the same.
In current mode, the overranges are typically 2%. In current
mode, the overrange capability is only available on three ranges,
0 mA to 20 mA, 0 mA to 24 mA, and 4 mA to 20 mA. For these
ranges, the analog input also remains the same (0 V to 4.096 V).
C(x) = x8 + x2 + x1 + 1
This is added to the end of the data-word, and 24 data bits are
sent to the AD5751 before taking SYNC high. If the AD5751
receives a 24-bit data frame, it performs the error check when
SYNC goes high. If the check is valid, then the data is written to
the selected register. If the error check fails, the FAULT pin
goes low and Bit D3 of the status register is set. After reading
this register, this error flag is cleared automatically and the
FAULT pin goes high again.
UPDATE ON SYNC HIGH
SYNC
SCLK
D15
(MSB)
D0
(LSB)
16-BIT DATA
SDIN
16-BIT DATA TRANSER—NO ERROR CHECKING
UPDATE AFTER SYNC HIGH
ONLY IF ERROR CHECK PASSED
SYNC
SCLK
SDIN
FAULT
D8
(LSB)
16-BIT DATA
D7
D0
8-BIT FCS
FAULT GOES LOW IF
ERROR CHECK FAILS
16-BIT DATA TRANSER WITH ERROR CHECKING
Figure 54. PEC Error Checking Timing
Rev. E | Page 28 of 32
07269-010
D23
(MSB)
Data Sheet
AD5751
APPLICATIONS INFORMATION
TRANSIENT VOLTAGE PROTECTION
THERMAL CONSIDERATIONS
The AD5751 contains ESD protection diodes that prevent damage
from normal handling. The industrial control environment can,
however, subject I/O circuits to much higher transients. To protect
the AD5751 from excessively high voltage transients, external
power diodes and a surge current limiting resistor may be
required, as shown in Figure 55. The constraint on the resistor
value is that during normal operation the output level at IOUT
must remain within its voltage compliance limit of AVDD −
2.75 V and the two protection diodes and resistor must have
appropriate power ratings. Further protection can be added
with transient voltage suppressors if needed.
It is important to understand the effects of power dissipation
on the package and how it affects junction temperature. The
internal junction temperature should not exceed 125°C. The
AD5751 is packaged in a 32-lead, 5 mm × 5 mm LFCSP package. The thermal impedance, θJA, is 42°C/W. It is important that
the devices not be operated under conditions that cause the
junction temperature to exceed its limit. Worst-case conditions
occur when the AD5751 are operated from the maximum AVDD
(55 V) and driving the maximum current (24 mA) directly to
ground. The quiescent current of the AD5751 should also be
taken into account, nominally ~4 mA. The following calculations
estimate maximum power dissipation under these worst-case
conditions, and determine maximum ambient temperature based
on this. These figures assume that proper layout and grounding
techniques are followed to minimize power dissipation, as
outlined in the Layout Guidelines section.
AVDD
AVDD
IOUT
RP
RLOAD
07269-011
AD5751
Figure 55. Output Transient Voltage Protection
Table 12. Thermal and Supply Considerations
Considerations
Maximum allowed power dissipation when operating at an ambient
temperature of 85°C
32-Lead LFCSP Package
Maximum allowed ambient temperature when operating from a supply of
55 V and driving 24 mA directly to ground (include 4 mA for internal AD5751
current)
Maximum allowed supply voltage when operating at an ambient
temperature of 85°C and driving 24 mA directly to ground
TJMAX − (PD × θJA) = 125 − ((55 × 0.028) × 42) = 60.3°C
Rev. E | Page 29 of 32
TJMAX TA
θ JA
TJMAX TA
AI DD θ JA
125 85
0.95 W
42
125 85
0.028 42
34 V
AD5751
Data Sheet
In any circuit where accuracy is important, careful consideration
of the power supply and ground return layout helps to ensure
the rated performance. The PCB on which the AD5751 is
mounted should be designed so that the AD5751 lies on the
analog plane.
The AD5751 should have ample supply bypassing of 10 μF in
parallel with 0.1 μF on each supply, located as close to the
package as possible, ideally right up against the device. The
10 μF capacitors are the tantalum bead type. The 0.1 μF capacitor should have low effective series resistance (ESR) and low
effective series inductance (ESI) such as the common ceramic
types, which provide a low impedance path to ground at high
frequencies to handle transient currents due to internal logic
switching.
In systems where there are many devices on one board, it is often
useful to provide some heat sinking capability to allow the power
to dissipate easily.
paddle on the bottom of the package should be soldered to the
corresponding thermal land paddle on the PCB (GND).
Thermal vias should be designed into the PCB land paddle area
to further improve heat dissipation.
GALVANICALLY ISOLATED INTERFACE
In many process control applications, it is necessary to provide
an isolation barrier between the controller and the unit being
controlled to protect and isolate the controlling circuitry from
any hazardous common-mode voltages that may occur. The
iCoupler® family of products from Analog Devices, Inc., provides
voltage isolation in excess of 5.0 kV. The serial loading structure
of the AD5751 makes it ideal for isolated interfaces because the
number of interface lines is kept to a minimum. Figure 57 shows a
4-channel isolated interface to the AD5751 using an ADuM1400.
For further information, visit
http://www.analog.com/icouplers.
CONTROLLER
AD5751
ADuM14001
SERIAL
CLOCK OUT
VIA
SERIAL
DATA OUT
VIB
SYNC OUT
CONTROL OUT
VIC
VID
ENCODE
DECODE
ENCODE
DECODE
ENCODE
DECODE
ENCODE
DECODE
GND
PLANE
1ADDITIONAL
PINS OMITTED FOR CLARITY.
VOA
TO
SCLK
VOB
TO
SDIN
VOC
TO
SYNC
VOD
TO
CLEAR
07269-013
LAYOUT GUIDELINES
07269-012
Figure 57. Isolated Interface
BOARD
MICROPROCESSOR INTERFACING
Figure 56. Paddle Connection to Board
The AD5751 has an exposed paddle beneath the device.
Connect this paddle to the GND of the AD5751. For optimum
performance, special considerations should be used to design
the motherboard and to mount the package. For enhanced
thermal, electrical, and board level performance, the exposed
Microprocessor interfacing to the AD5751 is via a serial bus that
uses a protocol compatible with microcontrollers and DSP processors. The communication channel is a 3-wire (minimum)
interface consisting of a clock signal, a data signal, and a SYNC
signal. The AD5751 requires a 16-bit data-word with data valid
on the falling edge of SCLK.
Rev. E | Page 30 of 32
Data Sheet
AD5751
OUTLINE DIMENSIONS
DETAIL A
(JEDEC 95)
0.30
0.25
0.18
25
PIN 1
IN D IC AT O R AR E A OP T IO N S
(SEE DETAIL A)
32
24
1
0.50
BSC
3.25
3.10 SQ
2.95
EXPOSED
PAD
17
TOP VIEW
0.80
0.75
0.70
SIDE VIEW
PKG-003898
SEATING
PLANE
0.50
0.40
0.30
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
8
9
16
BOTTOM VIEW
0.20 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WHHD
09-12-2018-A
PIN 1
INDICATOR
AREA
5.10
5.00 SQ
4.90
Figure 58. 32-Lead Lead Frame Chip Scale Package [LFCSP]
5 mm × 5 mm Body and 0.75 mm Package Height
(CP-32-7)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD5751ACPZ
AD5751ACPZ-REEL7
AD5751BCPZ
1
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
32-Lead LFCSP
32-Lead LFCSP
32-Lead LFCSP
Z = RoHS Compliant Part.
Rev. E | Page 31 of 32
Package Option
CP-32-7
CP-32-7
CP-32-7
AD5751
Data Sheet
NOTES
©2009–2020 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07269-9/20(E)
Rev. E | Page 32 of 32
工商网监
湘ICP备2023018690号
