AD633AR-REEL7

a FEATURES Four-Quadrant Multiplication Low Cost 8-Lead Package Complete—No External Components Required Laser-Trimmed Accuracy and Stability Total Error Within 2% of FS Differential High Impedance X and Y Inputs High Impedance Unity-Gain Summing Input Laser-Trimmed 10 V Scaling Reference APPLICATIONS Multiplication, Division, Squaring Modulation/Demodulation, Phase Detection Voltage-Controlled Amplifiers/Attenuators/Filters X1 1 1 X2 2 1 10V Low Cost Analog Multiplier AD633 CONNECTION DIAGRAMS 8-Lead Plastic DIP (N) Package 8 +VS A 7 W Y1 3 6 Z Y2 4 1 5 –VS AD633JN/AD633AN 8-Lead Plastic SOIC (SO-8) Package PRODUCT DESCRIPTION Y1 1 The AD633 is a functionally complete, four-quadrant, analog multiplier. It includes high impedance, differential X and Y inputs and a high impedance summing input (Z). The low impedance output voltage is a nominal 10 V full scale provided by a buried Zener. The AD633 is the first product to offer these features in modestly priced 8-lead plastic DIP and SOIC packages. The AD633 is laser calibrated to a guaranteed total accuracy of 2% of full scale. Nonlinearity for the Y-input is typically less than 0.1% and noise referred to the output is typically less than 100 µV rms in a 10 Hz to 10 kHz bandwidth. A 1 MHz bandwidth, 20 V/µs slew rate, and the ability to drive capacitive loads make the AD633 useful in a wide variety of applications where simplicity and cost are key concerns. The AD633’s versatility is not compromised by its simplicity. The Z-input provides access to the output buffer amplifier, enabling the user to sum the outputs of two or more multipliers, increase the multiplier gain, convert the output voltage to a current, and configure a variety of applications. The AD633 is available in an 8-lead plastic DIP package (N) and 8-lead SOIC (R). It is specified to operate over the 0°C to +70°C commercial temperature range (J Grade) or the –40° C to +85°C industrial temperature range (A Grade). 1 1 10V A 1 8 X2 Y2 2 7 X1 –VS 3 6 +VS Z 4 5 W AD633JR/AD633AR W= (X1 – X2) (Y1 – Y2) 10V +Z PRODUCT HIGHLIGHTS 1. The AD633 is a complete four-quadrant multiplier offered in low cost 8-lead plastic packages. The result is a product that is cost effective and easy to apply. 2. No external components or expensive user calibration are required to apply the AD633. 3. Monolithic construction and laser calibration make the device stable and reliable. 4. High (10 MΩ) input resistances make signal source loading negligible. 5. Power supply voltages can range from ± 8 V to ± 18 V. The internal scaling voltage is generated by a stable Zener diode; multiplier accuracy is essentially supply insensitive. REV. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 1999 AD633–SPECIFICATIONS Model TRANSFER FUNCTION Parameter MULTIPLIER PERFORMANCE Total Error TMIN to TMAX Scale Voltage Error Supply Rejection Nonlinearity, X Nonlinearity, Y X Feedthrough Y Feedthrough Output Offset Voltage DYNAMICS Small Signal BW Slew Rate Settling Time to 1% OUTPUT NOISE Spectral Density Wideband Noise OUTPUT Output Voltage Swing Short Circuit Current INPUT AMPLIFIERS Signal Voltage Range Offset Voltage X, Y CMRR X, Y Bias Current X, Y, Z Differential Resistance POWER SUPPLY Supply Voltage Rated Performance Operating Range Supply Current (TA = +25 C, V S = 15 V, RL ≥ 2 k ) AD633J, AD633A W= (X 1 − X 2 Y1 − Y2 10 V )( )+Z Unit % Full Scale % Full Scale % Full Scale % Full Scale % Full Scale % Full Scale % Full Scale % Full Scale mV MHz V/µs µs µV/√Hz mV rms µV rms V mA V V mV dB µA MΩ Conditions –10 V ≤ X, Y ≤ +10 V SF = 10.00 V Nominal VS = ± 14 V to ± 16 V X = ± 10 V, Y = +10 V Y = ± 10 V, X = +10 V Y Nulled, X = ± 10 V X Nulled, Y = ± 10 V Min Typ ±1 ±3 ± 0.25% ± 0.01 ± 0.4 ± 0.1 ± 0.3 ± 0.1 ±5 1 20 2 0.8 1 90 Max 2 1 0.4 1 0.4 50 VO = 0.1 V rms VO = 20 V p-p ∆ V O = 20 V f = 10 Hz to 5 MHz f = 10 Hz to 10 kHz 11 RL = 0 Ω Differential Common Mode VCM = ± 10 V, f = 50 Hz 30 10 10 60 40 ±5 80 0.8 10 30 2.0 ± 15 8 Quiescent 4 6 18 V V mA NOTES Specifications shown in boldface are tested on all production units at electrical test. Results from those tests are used to calculate outgoing quality levels. All min and max specifications are guaranteed, although only those shown in boldface are tested on all production units. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS 1 Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V Internal Power Dissipation2 . . . . . . . . . . . . . . . . . . . . 500 mW Input Voltages3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V Output Short Circuit Duration . . . . . . . . . . . . . . . . . Indefinite Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C Operating Temperature Range AD633J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C AD633A . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 V NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. 2 8-Lead Plastic DIP Package: θ JA = 90 °C/W; 8-Lead Small Outline Package: θ JA = 155 °C/W. 3 For supply voltages less than ± 18 V, the absolute maximum input voltage is equal to the supply voltage. ORDERING GUIDE Temperature Range –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C Package Description Plastic DIP Plastic SOIC 13" Tape and Reel 7" Tape and Reel Plastic DIP Plastic SOIC 13" Tape and Reel 7" Tape and Reel Package Option N-8 SO-8 SO-8 SO-8 N-8 SO-8 SO-8 SO-8 Model AD633AN AD633AR AD633AR-REEL AD633AR-REEL7 AD633JN AD633JR AD633JR-REEL AD633JR-REEL7 –2– REV. B AD633 FUNCTIONAL DESCRIPTION The AD633 is a low cost multiplier comprising a translinear core, a buried Zener reference, and a unity gain connected output amplifier with an accessible summing node. Figure 1 shows the functional block diagram. The differential X and Y inputs are converted to differential currents by voltage-to-current converters. The product of these currents is generated by the multiplying core. A buried Zener reference provides an overall scale factor of 10 V. The sum of (X × Y)/10 + Z is then applied to the output amplifier. The amplifier summing node Z allows the user to add two or more multiplier outputs, convert the output voltage to a current, and configure various analog computational functions. +VS voltage controlled amplifiers, and frequency doublers. Note that these applications show the pin connections for the AD633JN pinout (8-lead DIP), which differs from the AD633JR pinout (8-lead SOIC). Multiplier Connections Figure 3 shows the basic connections for multiplication. The X and Y inputs will normally have their negative nodes grounded, but they are fully differential, and in many applications the grounded inputs may be reversed (to facilitate interfacing with signals of a particular polarity, while achieving some desired output polarity) or both may be driven. +15V 0.1 F X1 1 1 A 1 10V 8 X INPUT 1 2 3 4 X1 X2 Y1 Y2 +VS 8 W7 Z6 –VS 5 0.1 F –15V 10V OPTIONAL SUMMING INPUT, Z W= (X1 – X2) (Y1 – Y2) +Z AD633JN X2 2 7 W Y INPUT Y1 3 6 Z Y2 4 1 AD633 5 –VS Figure 3. Basic Multiplier Connections Figure 1. Functional Block Diagram (AD633JN Pinout Shown) Squaring and Frequency Doubling Inspection of the block diagram shows the overall transfer function to be: W= (X 1 − X 2 Y1 − Y2 10 V )( )+Z (Equation 1) As Figure 4 shows, squaring of an input signal, E, is achieved simply by connecting the X and Y inputs in parallel to produce an output of E2/10 V. The input may have either polarity, but the output will be positive. However, the output polarity may be reversed by interchanging the X or Y inputs. The Z input may be used to add a further signal to the output. +15V 0.1 F E 1 2 3 4 ERROR SOURCES X1 X2 Y1 Y2 +VS 8 W7 Z6 –VS 5 0.1 F –15V W= E2 10V Multiplier errors consist primarily of input and output offsets, scale factor error, and nonlinearity in the multiplying core. The input and output offsets can be eliminated by using the optional trim of Figure 2. This scheme reduces the net error to scale factor errors (gain error) and an irreducible nonlinearity component in the multiplying core. The X and Y nonlinearities are typically 0.4% and 0.1% of full scale, respectively. Scale factor error is typically 0.25% of full scale. The high impedance Z input should always be referenced to the ground point of the driven system, particularly if this is remote. Likewise, the differential X and Y inputs should be referenced to their respective grounds to realize the full accuracy of the AD633. +VS AD633JN Figure 4. Connections for Squaring When the input is a sine wave E sin ωt, this squarer behaves as a frequency doubler, since (E sin ωt ) 10 V 2 = 50k 300k 1k 50mV TO APPROPRIATE INPUT TERMINAL (E.G. X2, X2, Z) E2 1 − cos 2 ωt 20 V ( ) (Equation 2) –VS Equation 2 shows a dc term at the output which will vary strongly with the amplitude of the input, E. This can be avoided using the connections shown in Figure 5, where an RC network is used to generate two signals whose product has no dc term. It uses the identity: Figure 2. Optional Offset Trim Configuration APPLICATIONS The AD633 is well suited for such applications as modulation and demodulation, automatic gain control, power measurement, cos θ sin θ = 1 sin 2 θ 2 ( ) (Equation 3) REV. B –3– AD633 +15V 0.1 F E R 1 2 3 4 R 10k +15V W= R2 3k E2 10V E R 10k +15 0.1 F 0.1 F EX 1 2 X1 X2 Y1 Y2 +VS 8 W7 Z6 –VS 5 0.1 F –15V R1 1k X1 X2 Y1 Y2 +VS 8 W7 AD633JN C AD633JN AD711 0.1 F –15 3 4 1N4148 Z6 0.1 F –VS 5 –15V W = –10V E EX Figure 5. ”Bounceless” Frequency Doubler At ωo = 1/CR, the X input leads the input signal by 45° (and is attenuated by √2), and the Y input lags the X input by 45° (and is also attenuated by √2). Since the X and Y inputs are 90° out of phase, the response of the circuit will be (satisfying Equation 3): W= E Figure 7. Connections for Division (10 V ) 2 1 E (sin ω t + 45°) 2 o o E 2 (sin ω t − 45°) o Likewise, Figure 7 shows how to implement a divider using a multiplier in a feedback loop. The transfer function for the divider is W = − 10 V ( = (40 V ) (sin 2 ω t ) (Equation 4) ) EE (Equation 6) +15V 0.1 F X which has no dc component. Resistors R1 and R2 are included to restore the output amplitude to 10 V for an input amplitude of 10 V. The amplitude of the output is only a weak function of frequency: the output amplitude will be 0.5% too low at ω = 0.9 ω o, and ω o = 1.1 ω o. Generating Inverse Functions X INPUT 1 2 X1 X2 Y1 Y2 +VS 8 W7 R1 R2 Z6 –VS 5 0.1 F –15V S W= (X1 – X2) (Y1 – Y2) 10V 1k R1, R2 (R1 + R2) R1 100k +S AD633JN Y INPUT 3 4 Inverse functions of multiplication, such as division and square rooting, can be implemented by placing a multiplier in the feedback loop of an op amp. Figure 6 shows how to implement a square rooter with the transfer function W= − 10 V E Figure 8. Connections for Variable Scale Factor Variable Scale Factor ( ) (Equation 5) for the condition E