AD7706BRUZ-REEL7

3 V/5 V, 1 mW, 2-/3-Channel, 16-Bit, Sigma-Delta ADCs AD7705/AD7706 FEATURES AD7705: 2 fully differential input channel ADCs AD7706: 3 pseudo differential input channel ADCs 16 bits no missing codes 0.003% nonlinearity Programmable gain front end: gains from 1 to 128 3-wire serial interface SPI®-, QSPI™-, MICROWIRE™-, and DSP-compatible Schmitt-trigger input on SCLK Ability to buffer the analog input 2.7 V to 3.3 V or 4.75 V to 5.25 V operation Power dissipation 1 mW maximum @ 3 V Standby current 8 μA maximum 16-lead PDIP, 16-lead SOIC, and 16-lead TSSOP packages GENERAL DESCRIPTION FUNCTIONAL BLOCK DIAGRAM VDD REF IN(–) REF IN(+) AD7705/AD7706 CHARGE BALANCING A/D CONVERTER ANALOG INPUT CHANNELS MAX BUFFER Σ -Δ MODULATOR PGA A = 1 ≈ 128 DIGITAL FILTER SERIAL INTERFACE REGISTER BANK MCLK IN MCLK OUT SCLK CLOCK GENERATION CS DIN The AD7705/AD7706 devices operate from a single 2.7 V to 3.3 V or 4.75 V to 5.25 V supply. The AD7705 features two fully differential analog input channels; the AD7706 features three pseudo differential input channels. Both devices feature a differential reference input. Input signal ranges of 0 mV to 20 mV through 0 V to 2.5 V can be incorporated on both devices when operating with a VDD of 5 V and a reference of 2.5 V. They can also handle bipolar input signal ranges of ±20 mV through ±2.5 V, which are referenced to the AIN(−) inputs on the AD7705 and to the COMMON input on the AD7706. DOUT GND DRDY RESET 01166-001 The AD7705/AD7706 are complete analog front ends for low frequency measurement applications. These 2-/3-channel devices can accept low level input signals directly from a transducer and produce serial digital output. The devices employ a Σ-Δ conversion technique to realize up to 16 bits of no missing codes performance. The selected input signal is applied to a proprietary, programmable-gain front end based around an analog modulator. The modulator output is processed by an onchip digital filter. The first notch of this digital filter can be programmed via an on-chip control register, allowing adjustment of the filter cutoff and output update rate. Figure 1. The AD7705/AD7706 devices, with a 3 V supply and a 1.225 V reference, can handle unipolar input signal ranges of 0 mV to 10 mV through 0 V to 1.225 V. The devices can accept bipolar input ranges of ±10 mV through ±1.225 V. Therefore, the AD7705/AD7706 devices perform all signal conditioning and conversion for a 2-channel or 3-channel system. The AD7705/AD7706 are ideal for use in smart, microcontroller, or DSP-based systems. The devices feature a serial interface that can be configured for 3-wire operation. Gain settings, signal polarity, and update rate selection can be configured in software using the input serial port. The parts contains self-calibration and system calibration options to eliminate gain and offset errors on the part itself or in the system. CMOS construction ensures very low power dissipation, and the power-down mode reduces the standby power consumption to 20 μW typ. These parts are available in a 16-lead, wide body (0.3 inch), plastic dual in-line package (DIP); a 16-lead, wide body (0.3 inch), standard small outline (SOIC) package; and a low profile, 16-lead, thin shrink small outline package (TSSOP). Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. AD7705/AD7706 TABLE OF CONTENTS Features .............................................................................................. 1 Reference Input........................................................................... 23 General Description ......................................................................... 1 Digital Filtering........................................................................... 23 Functional Block Diagram .............................................................. 1 Analog Filtering.......................................................................... 25 Revision History ............................................................................... 3 Calibration................................................................................... 25 Product Highlights ........................................................................... 4 Theory of Operation ...................................................................... 28 Specifications..................................................................................... 5 Clocking and Oscillator Circuit ............................................... 28 Timing Characteristics ................................................................ 8 System Synchronization ............................................................ 28 Absolute Maximum Ratings............................................................ 9 RESET Input ............................................................................... 29 ESD Caution.................................................................................. 9 Standby Mode ............................................................................. 29 Pin Configurations and Function Descriptions ......................... 10 Accuracy ...................................................................................... 29 Output Noise (5 V Operation)...................................................... 12 Drift Considerations .................................................................. 29 Output Noise (3 V Operation)...................................................... 13 Power Supplies ............................................................................ 30 Typical Performance Characteristics ........................................... 14 Supply Current............................................................................ 30 On-Chip Registers .......................................................................... 16 Grounding and Layout .............................................................. 30 Communication Register (RS2, RS1, RS0 = 0, 0, 0)............... 16 Evaluating the Performance...................................................... 31 Setup Register (RS2, RS1, RS0 = 0, 0, 1); Power-On/Reset Status: 01 Hexadecimal .............................................................. 17 Digital Interface.......................................................................... 31 Configuring the AD7705/AD7706 .......................................... 33 Clock Register (RS2, RS1, RS0 = 0, 1, 0); Power-On/Reset Status: 05 Hexadecimal .............................................................. 19 Microcomputer/Microprocessor Interfacing ......................... 34 Data Register (RS2, RS1, RS0 = 0, 1, 1) ................................... 20 Code For Setting Up the AD7705/AD7706............................ 35 Test Register (RS2, RS1, RS0 = 1, 0, 0); Power-On/Reset Status: 00 Hexadecimal .............................................................. 20 Applications..................................................................................... 38 Zero-Scale Calibration Register (RS2, RS1, RS0 = 1, 1, 0); Power-On/Reset Status: 1F4000 Hexadecimal ........................... 20 Full-Scale Calibration Register (RS2, RS1, RS0 = 1, 1, 1); Power-On/Reset Status: 5761AB HexaDecimal......................... 20 Pressure Measurement............................................................... 38 Temperature Measurement ....................................................... 39 Smart Transmitters..................................................................... 40 Battery Monitoring .................................................................... 41 Circuit Description......................................................................... 21 Outline Dimensions ....................................................................... 42 Analog Input ............................................................................... 22 Ordering Guide .......................................................................... 43 Bipolar/Unipolar Input .............................................................. 22 Rev. C | Page 2 of 44 AD7705/AD7706 REVISION HISTORY 5/06—Rev. B to Rev. C Updated Format.................................................................. Universal Changes to Table 1 ............................................................................3 Updated Outline Dimensions........................................................42 Changes to Ordering Guide...........................................................43 6/05—Rev. A to Rev. B Updated Format.................................................................. Universal Changed Range of Absolute Voltage on Analog Inputs Universal Changes to Table 19 ........................................................................21 Updated Outline Dimensions........................................................42 Changes to Ordering Guide...........................................................43 11/98—Rev. 0 to Rev. A Revision 0: Initial Version Rev. C | Page 3 of 44 AD7705/AD7706 PRODUCT HIGHLIGHTS 1. The AD7705/AD7706 devices consume less than 1 mW at 3 V supplies and 1 MHz master clock, making them ideal for use in low power systems. Standby current is less than 8 μA. 3. The AD7705/AD7706 are ideal for microcontroller or DSP processor applications with a 3-wire serial interface, reducing the number of interconnect lines and reducing the number of opto-couplers required in isolated systems. 2. The programmable gain input allows the AD7705/AD7706 to accept input signals directly from a strain gage or transducer, removing a considerable amount of signal conditioning. 4. The parts feature excellent static performance specifications with 16 bits, no missing codes, ±0.003% accuracy, and low rms noise (4000 V ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. C | Page 9 of 44 AD7705/AD7706 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS 16 MCLK IN 2 15 VDD MCLK OUT 3 14 DIN AD7705 SCLK 1 GND MCLK OUT 3 CS CS 4 TOP VIEW 13 DOUT RESET 5 (Not to Scale) 12 DRDY AIN1(+) 7 AIN1(–) 8 11 10 9 4 RESET 5 15 VDD AD7706 TOP VIEW (Not to Scale) 14 DIN 13 DOUT 12 DRDY AIN2(–) AIN1 6 11 AIN3 REF IN(–) AIN2 7 10 REF IN(–) REF IN(+) 01166-003 AIN2(+) 6 16 GND MCLK IN 2 COMMON 8 Figure 3. AD7705 Pin Configuration 9 REF IN(+) 01166-004 SCLK 1 Figure 4. AD7706 Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 Mnemonic AD7705 AD7706 SCLK SCLK 2 MCLK IN MCLK IN 3 MCLK OUT MCLK OUT 4 CS CS 5 RESET RESET 6 7 8 AIN2(+) AIN1(+) AIN1(−) AIN1 AIN2 COMMON 9 REF IN(+) REF IN(+) 10 REF IN(−) REF IN(−) 11 12 AIN2(−) DRDY AIN3 DRDY 13 DOUT DOUT Description Serial Clock. An external serial clock is applied to the Schmitt-triggered logic input to access serial data from the AD7705/AD7706. This serial clock can be a continuous clock with all data transmitted in a continuous train of pulses. Alternatively, it can be a noncontinuous clock with the information transmitted to the AD7705/AD7706 in smaller batches of data. Master Clock Signal. This can be provided in the form of a crystal/resonator or external clock. A crystal/resonator can be tied across the Pin MCLK IN and Pin MCLK OUT. Alternatively, the MCLK IN pin can be driven with a CMOS-compatible clock with the MCLK OUT pin left unconnected. The parts can be operated with clock frequencies in the range of 500 kHz to 5 MHz. When the master clock for these devices is a crystal/resonator, the crystal/resonator is connected between Pin MCLK IN and Pin MCLK OUT. If an external clock is applied to Pin MCLK IN, Pin MCLK OUT provides an inverted clock signal. This clock can be used to provide a clock source for external circuitry and is capable of driving 1 CMOS load. If the user does not require this clock externally, Pin MCLK OUT can be turned off via the CLKDIS bit of the clock register. This ensures that the part does not unnecessarily burn power driving capacitive loads on Pin MCLK OUT. Chip Select. Active low logic input used to select the AD7705/AD7706. With this input hardwired low, the AD7705/AD7706 can operate in its 3-wire interface mode with Pin SCLK, Pin DIN, and Pin DOUT used to interface to the device. The CS pin can be used to select the device communicating with the AD7705/AD7706. Logic Input. Active low input that resets the control logic, interface logic, calibration coefficients, digital filter, and analog modulator of the parts to power-on status. Positive Input of the Differential Analog Input Pair AIN2(+)/AIN2(−) for AD7705. Channel 1 for AD7706. Positive Input of the Differential Analog Input Pair AIN1(+)/AIN1(−) for AD7705. Channel 2 for AD7706. Negative Input of the Differential Analog Input Pair AIN1(+)/AIN1(−) for AD7705. COMMON input for AD7706 with Channel 1, Channel 2, and Channel 3 referenced to this input. Reference Input. Positive input of the differential reference input to the AD7705/AD7706. The reference input is differential with the provision that REF IN(+) must be greater than REF IN(−). REF IN(+) can lie anywhere between VDD and GND. Reference Input. Negative input of the differential reference input to the AD7705/AD7706. The REF IN(−) can lie anywhere between VDD and GND, provided that REF IN(+) is greater than REF IN(−). Negative Input of the Differential Analog Input Pair AIN2(+)/AIN2(−) for AD7705. Channel 3 for AD7706. Logic Output. A logic low on this output indicates that a new output word is available from the AD7705/AD7706 data register. The DRDY pin returns high upon completion of a read operation of a full output word. If no data read has taken place between output updates, the DRDY line returns high for 500 × tCLK IN cycles prior to the next output update. While DRDY is high, a read operation should neither be attempted nor in progress to avoid reading from the data register as it is being updated. The DRDY line returns low after the update has taken place. DRDY is also used to indicate when the AD7705/AD7706 has completed its on-chip calibration sequence. Serial Data Output. Serial data is read from the output shift register on the part. The output shift register can contain information from the setup register, communication register, clock register, or data register, depending on the register selection bits of the communication register. Rev. C | Page 10 of 44 AD7705/AD7706 Pin No. 14 Mnemonic AD7705 AD7706 DIN DIN 15 16 VDD GND VDD GND Description Serial Data Input. Serial data is written to the input shift register on the part. Data from the input shift register is transferred to the setup register, clock register, or communication register, depending on the register selection bits of the communication register. Supply Voltage. 2.7 V to 5.25 V operation. Ground Reference Point for the AD7705/AD7706 Internal Circuitry. Rev. C | Page 11 of 44 AD7705/AD7706 OUTPUT NOISE (5 V OPERATION) Note that these numbers represent the resolution for which there is no code flicker. They are not calculated based on rms noise, but on peak-to-peak noise. The numbers given are for bipolar input ranges with a VREF of 2.5 V for either buffered or unbuffered mode. These numbers are typical and are rounded to the nearest LSB. The numbers apply for the CLKDIV bit of the clock register set to 0. Table 5 shows the AD7705/AD7706 output rms noise for the selectable notch and −3 dB frequencies for the parts, as selected by FS0 and FS1 of the clock register. The numbers given are for the bipolar input ranges with a VREF of 2.5 V and VDD = 5 V. These numbers are typical and are generated at an analog input voltage of 0 V with the parts used in either buffered or unbuffered mode. Table 6 shows the output peak-to-peak noise for the selectable notch and −3 dB frequencies for the parts. Table 5. Output RMS Noise vs. Gain and Output Update Rate @ 5 V Filter First −3 dB Notch and Frequency O/P Data Rate MCLK IN = 2.4576 MHz 50 Hz 13.1 Hz 60 Hz 15.72 Hz 250 Hz 65.5 Hz 500 Hz 131 Hz MCLK IN = 1 MHz 20 Hz 5.24 Hz 25 Hz 6.55 Hz 100 Hz 26.2 Hz 200 Hz 52.4 Hz Typical Output RMS Noise in μV Gain of 1 Gain of 2 Gain of 4 Gain of 8 Gain of 16 Gain of 32 Gain of 64 Gain of 128 4.1 5.1 110 550 2.1 2.5 49 285 1.2 1.4 31 145 0.75 0.8 17 70 0.7 0.75 8 41 0.66 0.7 3.6 22 0.63 0.67 2.3 9.1 0.6 0.62 1.7 4.7 4.1 5.1 110 550 2.1 2.5 49 285 1.2 1.4 31 145 0.75 0.8 17 70 0.7 0.75 8 41 0.66 0.7 3.6 22 0.63 0.67 2.3 9.1 0.6 0.62 1.7 4.7 Table 6. Peak-to-Peak Resolution vs. Gain and Output Update Rate @ 5 V Filter First −3 dB Notch and O/P Data Rate Frequency MCLK IN = 2.4576 MHz 50 Hz 13.1 Hz 60 Hz 15.72 Hz 250 Hz 65.5 Hz 500 Hz 131 Hz MCLK IN = 1 MHz 20 Hz 5.24 Hz 25 Hz 6.55 Hz 100 Hz 26.2 Hz 200 Hz 52.4 Hz Typical Peak-to-Peak Resolution Bits Gain of 1 Gain of 2 Gain of 4 Gain of 8 Gain of 16 Gain of 32 Gain of 64 Gain of 128 16 16 13 10 16 16 13 10 16 16 13 10 16 16 13 10 16 15 13 10 16 14 13 10 15 14 12 10 14 13 12 10 16 16 13 10 16 16 13 10 16 16 13 10 16 16 13 10 16 15 13 10 16 14 13 10 15 14 12 10 14 13 12 10 Rev. C | Page 12 of 44 AD7705/AD7706 OUTPUT NOISE (3 V OPERATION) Note that these numbers represent the resolution for which there is no code flicker. They are not calculated based on rms noise, but on peak-to-peak noise. The numbers given are for bipolar input ranges with a VREF of 1.225 V for either buffered or unbuffered mode. These numbers are typical and are rounded to the nearest LSB. The numbers apply for the CLKDIV bit of the clock register set to 0. Table 7 shows the AD7705/AD7706 output rms noise for the selectable notch and −3 dB frequencies for the parts, as selected by FS0 and FS1 of the clock register. The numbers given are for the bipolar input ranges with a VREF of 1.225 V and a VDD = 3 V. These numbers are typical and are generated at an analog input voltage of 0 V with the parts used in either buffered or unbuffered mode. Table 8 shows the output peak-to-peak noise for the selectable notch and −3 dB frequencies for the parts. Table 7. Output RMS Noise vs. Gain and Output Update Rate @ 3 V Filter First −3 dB Notch and O/P Data Rate Frequency MCLK IN = 2.4576 MHz 50 Hz 13.1 Hz 60 Hz 15.72 Hz 250 Hz 65.5 Hz 500 Hz 131 Hz MCLK IN = 1 MHz 20 Hz 5.24 Hz 25 Hz 6.55 Hz 100 Hz 26.2 Hz 200 Hz 52.4 Hz Typical Output RMS Noise in μV Gain of 1 Gain of 2 Gain of 4 Gain of 8 Gain of 16 Gain of 32 Gain of 64 Gain of 128 3.8 5.1 50 270 2.4 2.9 25 135 1.5 1.7 14 65 1.3 1.5 9.9 41 1.1 1.2 5.1 22 1.0 1.0 2.6 9.7 0.9 0.9 2.3 5.1 0.9 0.9 2.0 3.3 3.8 5.1 50 270 2.4 2.9 25 135 1.5 1.7 14 65 1.3 1.5 9.9 41 1.1 1.2 5.1 22 1.0 1.0 2.6 9.7 0.9 0.9 2.3 5.1 0.9 0.9 2.0 3.3 Table 8. Peak-to-Peak Resolution vs. Gain and Output Update Rate @ 3 V Filter First Notch and −3 dB O/P Data Rate Frequency MCLK IN = 2.4576 MHz 50 Hz 13.1 Hz 60 Hz 15.72 Hz 250 Hz 65.5 Hz 500 Hz 131 Hz MCLK IN = 1 MHz 20 Hz 5.24 Hz 25 Hz 6.55 Hz 100 Hz 26.2 Hz 200 Hz 52.4 Hz Typical Peak-to-Peak Resolution in Bits Gain of 1 Gain of 2 Gain of 4 Gain of 8 Gain of 16 Gain of 32 Gain of 64 Gain of 128 16 16 13 10 16 16 13 10 15 15 13 10 15 14 13 10 14 14 12 10 13 13 12 10 13 13 11 10 12 12 11 10 16 16 13 10 16 16 13 10 15 15 13 10 15 14 13 10 14 14 12 10 13 13 12 10 13 13 11 10 12 12 11 10 Rev. C | Page 13 of 44 AD7705/AD7706 TYPICAL PERFORMANCE CHARACTERISTICS 32771 VDD = 5V VREF = 2.5V GAIN = +128 50Hz UPDATE RATE 32770 400 TA = 25°C RMS NOISE = 600nV 300 OCCURRENCE 32768 32767 32766 32765 100 01166-005 32764 32763 200 0 100 200 300 400 500 600 700 READING NUMBER 800 01166-008 CODE READ 32769 0 900 1000 32765 32764 32766 32767 CODE 32768 32769 32770 Figure 8. Histogram of Data in Figure 5 Figure 5. Noise @ Gain = +128 With 50 Hz Update Rate 1.2 1.2 VDD = 3V TA = 25°C VDD = 5V TA = +25°C BUFFERED MODE, GAIN = +128 1.0 1.0 0.8 0.8 BUFFERED MODE, GAIN = +128 IDD (mA) IDD (mA) BUFFERED MODE, GAIN = +1 BUFFERED MODE, GAIN = +1 0.6 0.4 0.6 0.4 UNBUFFERED MODE, GAIN = +128 UNBUFFERED MODE, GAIN = +128 UNBUFFERED MODE, GAIN = +1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 FREQUENCY (MHz) 2.0 2.2 2.4 UNBUFFERED MODE, GAIN = +1 0 0.4 2.6 Figure 6. IDD vs. MCLK IN Frequency @ 3 V 1.0 0.5 0.4 UNBUFFERED MODE fCLK = 2.84MHz, CLKDIV = 0 0.3 VDD = 3V EXTERNAL MCLK CLKDIS = 1 TA = 25°C 0.1 2 4 8 16 32 2.2 2.4 2.6 64 UNBUFFERED MODE fCLK = 5MHz, CLKDIV = 1 0.6 UNBUFFERED MODE fCLK = 2.4576MHz, CLKDIV = 0 VDD = 5V EXTERNAL MCLK CLKDIS = 1 TA = 25°C 0.2 BUFFERED MODE fCLK = 1MHz, CLKDIV = 0 0 1 2.0 BUFFERED MODE fCLK = 2.4576MHz, CLKDIV = 0 0.4 01166-007 0.2 1.2 1.4 1.6 1.8 FREQUENCY (MHz) UNBUFFERED MODE fCLK = 1MHz, 0.8 CLKDIV = 0 UNBUFFERED MODE fCLK = 5MHz, CLKDIV = 1 0.6 1.0 BUFFERED MODE fCLK = 5MHz, CLKDIV = 1 1.0 BUFFERED MODE fCLK = 2.4576MHz, CLKDIV = 0 UNBUFFERED MODE fCLK = 1MHz, CLKDIV = 0 0.7 IDD (mA) 1.2 IDD (mA) 0.8 0.8 Figure 9. IDD vs. MCLK IN Frequency @ 5 V BUFFERED MODE fCLK = 5MHz, CLKDIV = 1 0.9 0.6 128 0 1 2 4 BUFFERED MODE fCLK = 1MHz, CLKDIV = 0 8 16 32 64 GAIN GAIN Figure 10. IDD vs. Gain and Clock Frequency @ 5 V Figure 7. IDD vs. Gain and Clock Frequency @ 3 V Rev. C | Page 14 of 44 01166-010 0 0.4 01166-009 0.2 01166-006 0.2 128 AD7705/AD7706 20 TEK STOP: SINGLE SEQ 50.0kS/s VDD 16 STANDBY CURRENT (μA) 1 2 OSCILLATOR = 4.9152MHz MCLK IN = 0V OR VDD 12 VDD = 5V 8 VDD = 3V OSCILLATOR = 2.4576MHz CH1 5.00V CH2 2.00V 5ms/DIV Figure 11. Crystal Oscillator Power-Up Time 0 –40 –30 –20 –10 01166-012 2 01166-011 4 0 10 20 30 40 TEMPERATURE (°C) 50 60 Figure 12. Standby Current vs. Temperature Rev. C | Page 15 of 44 70 80 AD7705/AD7706 ON-CHIP REGISTERS The AD7705/AD7706 each contain eight on-chip registers that can be accessed via the serial port. The first of these is a communication register that controls the channel selection, decides whether the next operation is a read or write operation, and decides which register the next read or write operation accesses. All communication to the AD7705/AD7706 must start with a write operation to the communication register. After a poweron or reset, the device expects a write to its communication register. The data written to this register determines whether the next operation is a read or write operation and to which register this operation occurs. Therefore, write access to any register on the part starts with a write operation to the communication register, followed by a write to the selected register. Likewise, a read operation from any register on the part, including the communication register itself and the output data register, starts with a write operation to the communication register, followed by a read operation from the selected register. The communication register also controls the standby mode and channel selection. The DRDY status is available by reading from the communication register. The second register is a setup register that determines calibration mode, gain setting, bipolar/unipolar operation, and buffered mode. The third register is labeled the clock register and contains the filter selection bits and clock control bits. The fourth register is the data register from which the output data is accessed. The final registers are the calibration registers, which store channel calibration data. The registers are discussed in more detail in the following sections. COMMUNICATION REGISTER (RS2, RS1, RS0 = 0, 0, 0) The communication register is an 8-bit register from which data can be read or to which data can be written. All communication to the part must start with a write operation to its communication register. The data written to the communication register determines whether the next operation is a read or write operation and to which register this operation takes place. After the read or write operation is complete, the interface returns to its default state, where it expects a write operation to the communication register. In situations where the interface sequence is lost, a write operation of a least 32 serial clock cycles with DIN high returns the ADC to its default state by resetting the part. Table 10 outlines the bit designations for the communication register. Table 9. Communication Register 0/DRDY (0) RS2 (0) RS1 (0) RS0 (0) R/W (0) STBY (0) CH1 (0) CH0 (0) Table 10. Communication Register Bit Description Register 0/DRDY RS2–RS0 R/W STBY CH1, CH0 Description For a write operation to the communications register, a 0 must be written to this bit. If a 1 is written to this bit, the part does not clock subsequent bits into the register. It stays at this bit location until a 0 is written. Then, the next seven bits are loaded into the communication register. For a read operation, this bit provides the status of the DRDY flag, which is the same as the DRDY output pin. Register Selection Bits. These bits are used to select which of the AD7705/AD7706 registers are being accessed during the serial interface communication. Read/WRITE Select. This bit selects whether the next operation is a read or write operation. A 0 indicates a write cycle for the next operation to the selected register, and a 1 indicates a read operation from the selected register. Standby. Writing 1 to this bit puts the part into standby or power-down mode. In this mode, the part consumes only 10 μA of power supply current. The part retains its calibration coefficients and control word information when in standby. Writing 0 to this bit places the parts in normal operating mode. Channel Select. These two bits select a channel for conversion or for access to the calibration coefficients, as outlined in Table 12. Following a calibration on a channel, three pairs of calibration registers store the calibration coefficients. Table 12 (for the AD7705) and Table 13 (for the AD7706) show which channel combinations have independent calibration coefficients. With CH1 at Logic 1 and CH0 at Logic 0, the AD7705 looks at the AIN1(−) input internally shorted to itself, while the AD7706 looks at the COMMON input internally shorted to itself. This can be used as a test method to evaluate the noise performance of the parts with no external noise sources. In this mode, the AIN1(−)/COMMON input should be connected to an external voltage within the allowable common-mode range for the parts. Rev. C | Page 16 of 44 AD7705/AD7706 Table 11. Register Selection RS2 0 0 0 0 1 1 1 1 RS1 0 0 1 1 0 0 1 1 RS0 0 1 0 1 0 1 0 1 Register Communication register Setup register Clock register Data register Test register No operation Offset register Gain register Register Size 8 bits 8 bits 8 bits 16 bits 8 bits 24 bits 24 bits Table 12. Channel Selection for AD7705 CH1 0 0 1 1 CH0 0 1 0 1 AIN(+) AIN1(+) AIN2(+) AIN1(−) AIN1(−) AIN(−) AIN1(−) AIN2(−) AIN1(−) AIN2(−) Calibration Register Pair Register Pair 0 Register Pair 1 Register Pair 0 Register Pair 2 Table 13. Channel Selection for AD7706 CH1 0 0 1 1 CH0 0 1 0 1 AIN AIN1 AIN2 COMMON AIN3 Reference COMMON COMMON COMMON COMMON Calibration Register Pair Register Pair 0 Register Pair 1 Register Pair 0 Register Pair 2 SETUP REGISTER (RS2, RS1, RS0 = 0, 0, 1); POWER-ON/RESET STATUS: 01 HEXADECIMAL The setup register is an 8-bit register from which data can be read or to which data can be written. Table 14 outlines the bit designations for the setup register. Table 14. Setup Register MD1 (0) MD0 (0) G2 (0) G1 (0) G0 (0) B/U (0) BUF (0) FSYNC (1) Table 15. Setup Register Description Register MD1, MD0 G2 to G0 B/U BUF FSYNC Description ADC Mode Bits. These bits select the operational mode of the ADC as outlined in Table 16. Gain Selection Bits. These bits select the gain setting for the on-chip PGA, as outlined in Table 17. Bipolar/Unipolar Operation. A 0 in this bit selects bipolar operation; a 1 in this bit selects unipolar operation. Buffer Control. With this bit at 0, the on-chip buffer on the analog input is shorted out. With the buffer shorted out, the current flowing in the VDD line is reduced. When this bit is high, the on-chip buffer is in series with the analog input, allowing the input to handle higher source impedances. Filter Synchronization. When this bit is high, the nodes of the digital filter, the filter control logic, the calibration control logic, and the analog modulator are held in a reset state. When this bit goes low, the modulator and filter start to process data, and a valid word is available in 3 × 1/output rate, that is, the settling time of the filter. This FSYNC bit does not affect the digital interface and does not reset the DRDY output if it is low. Rev. C | Page 17 of 44 AD7705/AD7706 Table 16. Operating Mode Options MD1 0 0 MD0 0 1 1 0 1 1 Operating Mode Normal Mode. In this mode, the device performs normal conversions. Self-Calibration. This activates self-calibration on the channel selected by CH1 and CH0 of the communication register. This is a one-step calibration sequence. When the sequence is complete, the part returns to normal mode, with both MD1 and MD0 returning to 0. The DRDY output or bit goes high when calibration is initiated, and returns low when self-calibration is complete and a new valid word is available in the data register. The zero-scale calibration is performed at the selected gain on internally shorted (zeroed) inputs, and the full-scale calibration is performed at the selected gain on an internally generated VREF/selected gain. Zero-Scale System Calibration. This activates zero-scale system calibration on the channel selected by CH1 and CH0 of the communication register. Calibration is performed at the selected gain on the input voltage provided at the analog input during this calibration sequence. This input voltage should remain stable for the duration of the calibration. The DRDY output or bit goes high when calibration is initiated, and returns low when zero-scale calibration is complete and a new valid word is available in the data register. At the end of the calibration, the part returns to normal mode, with both MD1 and MD0 returning to 0. Full-Scale System Calibration. This activates full-scale system calibration on the selected input channel. Calibration is performed at the selected gain on the input voltage provided at the analog input during this calibration sequence. This input voltage should remain stable for the duration of the calibration. The DRDY output or bit goes high when calibration is initiated, and returns low when full-scale calibration is complete and a new valid word is available in the data register. At the end of the calibration, the part returns to normal mode, with both MD1 and MD0 returning to 0. Table 17. Gain Selection G2 0 0 0 0 1 1 1 1 G1 0 0 1 1 0 0 1 1 G0 0 1 0 1 0 1 0 1 Gain Setting 1 2 4 8 16 32 64 128 Rev. C | Page 18 of 44 AD7705/AD7706 CLOCK REGISTER (RS2, RS1, RS0 = 0, 1, 0); POWER-ON/RESET STATUS: 05 HEXADECIMAL The clock register is an 8-bit register from which data can be read or to which data can be written. Table 18 outlines the bit designations for the clock register. Table 18. Clock Register ZERO (0) ZERO (0) ZERO (0) CLKDIS (0) CLKDIV (0) CLK (1) FS1 (0) FS0 (1) Table 19. Clock Register Description Register ZERO CLKDIS CLKDIV CLK FS1, FS0 Description Zero. A zero must be written to these bits to ensure correct operation of the AD7705/AD7706. Failure to do so might result in unspecified operation of the device. Master Clock Disable Bit. Logic 1 in this bit disables the master clock, preventing it from appearing at the MCLK OUT pin. When disabled, the MCLK OUT pin is forced low. This feature allows the user the flexibility of either using the MCLK OUT as a clock source for other devices in the system, or turning off the MCLK OUT as a power-saving feature. When using an external master clock on the MCLK IN pin, the AD7705/AD7706 continue to have internal clocks and convert normally with the CLKDIS bit active. When using a crystal oscillator or ceramic resonator across Pin MCLK IN and Pin MCLK OUT, the AD7705/AD7706 clocks are stopped, and no conversions take place when the CLKDIS bit is active. Clock Divider Bit. With this bit at Logic 1, the clock frequency appearing at the MCLK IN pin is divided by 2 before being used internally by the AD7705/AD7706. For example, when this bit is set to Logic 1, the user can operate with a 4.9152 MHz crystal between Pin MCLK IN and Pin MCLK OUT, and internally the part operates with the specified 2.4576 MHz. With this bit at Logic 0, the clock frequency appearing at the MCLK IN pin is the frequency used internally by the part. Clock Bit. This bit should be set in accordance with the operating frequency of the AD7705/AD7706. If the device has a master clock frequency of 2.4576 MHz (CLKDIV = 0) or 4.9152 MHz (CLKDIV = 1), this bit should be set to Logic 1. If the device has a master clock frequency of 1 MHz (CLKDIV = 0) or 2 MHz (CLKDIV = 1), this bit should be set to Logic 0. This bit sets up the appropriate scaling currents for a given operating frequency and, together with FS1 and FS0, chooses the output update rate for the device. If this bit is not set correctly for the master clock frequency of the device, the AD7705/AD7706 might not operate to specification. Filter Selection Bits. Along with the CLK bit, FS1 and FS0 determine the output update rate, the filter’s first notch, and the −3 dB frequency, as outlined in Table 20. The on-chip digital filter provides a sinc3 (or (sinx/x)3) filter response. In association with the gain selection, it also determines the output noise of the device. Changing the filter notch frequency, as well as the selected gain, impacts resolution. Table 5 through Table 8 show the effects of filter notch frequency and gain on the output noise and effective resolution of the part. The output data rate, or effective conversion time, for the device is equal to the frequency selected for the first notch of the filter. For example, if the first notch of the filter is selected at 50 Hz, a new word is available at a 50 Hz output rate, or every 20 ms. If the first notch is at 500 Hz, a new word is available every 2 ms. A calibration should be initiated when any of these bits are changed. The settling time of the filter to a full-scale step input is worst case 4 × 1/(output data rate). For example, with the filter-first notch at 50 Hz, the settling time of the filter to a full-scale step input is 80 ms maximum. If the first notch is at 500 Hz, the settling time is 8 ms maximum. This settling time can be reduced to 3 × 1/(output data rate) by synchronizing the step input change with a reset of the digital filter. In other words, if the step input takes place with the FSYNC bit high, the settling time is 3 × 1/(output data rate) from the time when the FSYNC bit returns low. The −3 dB frequency is determined by the programmed first notch frequency according to the relationship: filter − 3 dB frequency = 0.262 × filter - first notch frequency Table 20. Output Update Rates CLK 1 0 0 0 0 1 1 1 1 1 FS1 0 0 1 1 0 0 1 1 FS0 0 1 0 1 0 1 0 1 Output Update Rate 20 Hz 25 Hz 100 Hz 200 Hz 50 Hz 60 Hz 250 Hz 500 Hz Assumes correct clock frequency on MCLK IN pin with the CLKDIV bit set appropriately. Rev. C | Page 19 of 44 −3 dB Filter Cutoff 5.24 Hz 6.55 Hz 26.2 Hz 52.4 Hz 13.1 Hz 15.7 Hz 65.5 Hz 131 Hz AD7705/AD7706 DATA REGISTER (RS2, RS1, RS0 = 0, 1, 1) The data register is a 16-bit, read-only register that contains the most up-to-date conversion result from the AD7705/AD7706. If the communication register sets up the part for a write operation to this register, a write operation must take place to return the part to its default state. However, the 16 bits of data written to the part will be ignored by the AD7705/AD7706. TEST REGISTER (RS2, RS1, RS0 = 1, 0, 0); POWER-ON/RESET STATUS: 00 HEXADECIMAL The part contains a test register that is used when testing the device. The user is advised not to change the status of any of the bits in this register from the default (power-on or reset) status of all 0s, because the part will be placed in one of its test modes and will not operate correctly. ZERO-SCALE CALIBRATION REGISTER (RS2, RS1, RS0 = 1, 1, 0); POWER-ON/RESET STATUS: 1F4000 HEXADECIMAL The AD7705/AD7706 contain independent sets of zero-scale registers, one for each of the input channels. Each register is a 24-bit read/write register; therefore, 24 bits of data must be written, or no data is transferred to the register. This register is used in conjunction with its associated full-scale register to form a register pair. These register pairs are associated with input channel pairs, as outlined in Table 12 and Table 13. While the part is set up to allow access to these registers over the digital interface, the parts themselves can no longer access the register coefficients to scale the output data correctly. As a result, the first output data read from the part after accessing the calibration registers (for either a read or write operation) might contain incorrect data. In addition, a write to the calibration register should not be attempted while a calibration is in progress. These eventualities can be avoided by taking the FSYNC bit in the mode register high before the calibration register operation, and taking it low after the operation is complete. FULL-SCALE CALIBRATION REGISTER (RS2, RS1, RS0 = 1, 1, 1); POWER-ON/RESET STATUS: 5761AB HEXADECIMAL The AD7705/AD7706 contain independent sets of full-scale registers, one for each of the input channels. Each register is a 24-bit read/write register; therefore, 24 bits of data must be written, or no data is transferred to the register. This register is used in conjunction with its associated zero-scale register to form a register pair. These register pairs are associated with input channel pairs, as outlined in Table 12 and Table 13. While the part is set up to allow access to these registers over the digital interface, the part itself can no longer access the register coefficients to scale the output data correctly. As a result, the first output data read from the part after accessing the calibration registers (for either a read or write operation) might contain incorrect data. In addition, a write to the calibration register should not be attempted while a calibration is in progress. These eventualities can be avoided by taking FSYNC bit in the mode register high before the calibration register operation, and taking it low after the operation is complete. Calibration Sequences The AD7705/AD7706 contain a number of calibration options, as previously outlined. Table 21 summarizes the calibration types, the operations involved, and the duration of the operations. There are two methods for determining the end of a calibration. The first is to monitor when DRDY returns low at the end of the sequence. This technique not only indicates when the sequence is complete, but also when the part has a valid new sample in its data register. This valid new sample is the result of a normal conversion that follows the calibration sequence. The second method for determining when calibration is complete is to monitor the MD1 and MD0 bits of the setup register. When these bits return to 0 following a calibration command, the calibration sequence is complete. This technique can indicate the completion of a calibration earlier than the first method can, but it cannot indicate when there is a valid new result in the data register. The time that it takes the mode bits, MD1 and MD0, to return to 0 represents the duration of the calibration. The sequence when DRDY goes low includes a normal conversion and a pipeline delay, tP, to scale the results of this first conversion correctly. Note that tP never exceeds 2000 × tCLKIN. The time for both methods is shown in Table 21. Table 21. Calibration Sequences Calibration Type MD1, MD0 Calibration Sequence Duration of Mode Bits Duration of DRDY Self-Calibration 0, 1 6 × 1/output rate 9 × 1/output rate + tP ZS System Calibration FS System Calibration 1, 0 1, 1 Internal ZS calibration @ selected gain + internal FS calibration @ selected gain ZS calibration on AIN @ selected gain FS calibration on AIN @ selected gain 3 × 1/output rate 3 × 1/output rate 4 × 1/output rate + tP 4 × 1/output rate + tP Rev. C | Page 20 of 44 AD7705/AD7706 CIRCUIT DESCRIPTION cycle contains the digital information. The programmable gain function on the analog input is also incorporated in this Σ-Δ modulator, with the input sampling frequency being modified to provide higher gains. A sinc3, digital, low-pass filter processes the output of the Σ-Δ modulator and updates the output register at a rate determined by the first notch frequency of this filter. The AD7705/AD7706 are Σ-Δ analog-to-digital converters (ADC) with on-chip digital filtering, intended for the measurement of wide, dynamic range, low frequency signals, such as those in industrial-control or process-control applications. Each contains a Σ-Δ (or charge-balancing) ADC, a calibration microcontroller with on-chip static RAM, a clock oscillator, a digital filter, and a bidirectional serial communication port. The parts consume only 320 μA of power supply current, making them ideal for batterypowered or loop-powered instruments. These parts operate with a supply voltage of 2.7 V to 3.3 V or 4.75 V to 5.25 V. The output data can be read from the serial port randomly or periodically at any rate up to the output register update rate. The frequency of the first notch of the digital filter ranges from 50 Hz to 500 Hz; therefore, the programmable range for the −3 dB frequency is 13.1 Hz to 131 Hz. With a master clock frequency of 1 MHz, the programmable range for this first notch frequency is 20 Hz to 200 Hz, giving a programmable range for the −3 dB frequency of 5.24 Hz to 52.4 Hz. The AD7705 contains two programmable-gain, fully differential analog input channels, and the AD7706 contains three pseudo differential analog input channels. The selectable gains on these inputs are 1, 2, 4, 8, 16, 32, 64, and 128, allowing the parts to accept unipolar signals of 0 mV to 20 mV and 0 V to 2.5 V, or bipolar signals in the range of ±20 mV to ±2.5 V when the reference input voltage equals 2.5 V. With a reference voltage of 1.225 V, the input ranges are from 0 mV to 10 mV and 0 V to 1.225 V in unipolar mode, and from ±10 mV to ±1.225 V in bipolar mode. Note that the bipolar ranges are with respect to AIN(−) on the AD7705, and with respect to COMMON on the AD7706, but not with respect to GND. The AD7705 basic connection diagram is shown in Figure 13. It shows the AD7705 driven from an analog 5 V supply. An AD780 or REF192 precision 2.5 V reference provides the reference source for the part. On the digital side, the part is configured for 3-wire operation with CS tied to GND. A quartz crystal or ceramic resonator provides the master clock source for the part. In most cases, it is necessary to connect capacitors on the crystal or resonator to ensure that it does not oscillate at overtones of its fundamental operating frequency. The values of capacitors vary, depending on the manufacturer’s specifications. The same setup applies to the AD7706. The input signal to the analog input is continuously sampled at a rate determined by the frequency of the master clock, MCLK IN, and the selected gain. A charge-balancing ADC (∑-Δ modulator) converts the sampled signal into a digital pulse train whose duty ANALOG 5V SUPPLY 10μF 0.1μF VDD DIFFERENTIAL ANALOG INPUT DRDY DATA READY DOUT RECEIVE (READ) AIN1(–) DIFFERENTIAL ANALOG INPUT AIN2(+) DIN SCLK GND SERIAL CLOCK 5V RESET VIN VOUT AD780/ REF192 SERIAL DATA AIN2(–) REF IN(+) 10μF CS 0.1μF REF IN(–) MCLK IN GND MCLK OUT Figure 13. AD7705 Basic Connection Diagram Rev. C | Page 21 of 44 CRYSTAL OR CERAMIC RESONATOR 01166-013 ANALOG 5V SUPPLY AD7705 AIN1(+) AD7705/AD7706 Table 22. External Resistance-Capacitance Combination for Unbuffered Mode (Without 16-Bit Gain Error) ANALOG INPUT Ranges The AD7705 contains two differential analog input pairs, AIN1(+)/AIN1(−) and AIN2(+)/AIN2(−). These input pairs provide programmable-gain, differential input channels that can handle either unipolar or bipolar input signals. It should be noted that the bipolar input signals are referenced to the respective AIN(−) input of each input pair. The AD7706 contains three pseudo differential analog input pairs, AIN1, AIN2, and AIN3, which are referenced to the COMMON input. In unbuffered mode, the common-mode range of the input is from GND to VDD, provided that the absolute value of the analog input voltage lies between GND − 100 mV and VDD + 30 mV. Therefore, in unbuffered mode, the part can handle both unipolar and bipolar input ranges for all gains. The AD7705 can tolerate absolute analog input voltages down to GND − 200 mV, but the leakage current increases at high temperatures. In buffered mode, the analog inputs can handle much larger source impedances, but the absolute input voltage range is restricted to between GND + 50 mV and VDD − 1.5 V, which also restricts the commonmode range. Therefore, in buffered mode, there are some restrictions on the allowable gains for bipolar input ranges. Care must be taken in setting up the common-mode voltage and input voltage ranges so that the above limits are not exceeded; otherwise, there is a degradation in linearity performance. In unbuffered mode, the analog inputs look directly into the 7 pF input sampling capacitor, CSAMP. The dc input leakage current in this unbuffered mode is 1 nA maximum. As a result, the analog inputs see a dynamic load that is switched at the input sample rate (see Figure 14). This sample rate depends on master clock frequency and selected gain. CSAMP is charged to AIN(+) and discharged to AIN(−) every input sample cycle. The effective on resistance of the switch, RSW, is typically 7 kΩ. CSAMP must be charged through RSW and any external source impedances every input sample cycle. Therefore, in unbuffered mode, source impedances mean a longer charge time for CSAMP, which might result in gain errors on the parts. Table 22 shows the allowable external resistance-capacitance values for unbuffered mode, such that no gain error to the 16-bit level is introduced in the part. Note that these capacitances are total capacitances on the analog input—external capacitance plus 10 pF capacitance from the pins and lead frame of the devices. AIN(–) RSW (7kΩ TYP) CSAMP (7pF) External Capacitance (pF) 50 100 500 1000 53.9 kΩ 31.4 kΩ 8.4 kΩ 4.76 kΩ 26.6 kΩ 15.4 kΩ 4.14 kΩ 2.36 kΩ 12.77 kΩ 7.3 kΩ 1.95 kΩ 1.15 kΩ 5.95 kΩ 3.46 kΩ 924 Ω 526 Ω 5000 1.36 kΩ 670 Ω 320 Ω 150 Ω Sample Rate The modulator sample frequency for the AD7705/AD7706 remains at fCLKIN/128 (19.2 kHz @ fCLKIN = 2.4576 MHz), regardless of the selected gain. However, gains greater than 1 are achieved by a combination of multiple input samples per modulator cycle and a scaling of the ratio of reference capacitor to input capacitor. As a result of the multiple sampling, the input sample rate of these devices varies with the selected gain (see Table 23). In buffered mode, the input is buffered before the input sampling capacitor. In unbuffered mode, where the analog input looks directly into the sampling capacitor, the effective input impedance is 1/CSAMP × fS, where CSAMP is the input sampling capacitance and fS is the input sample rate. Table 23. Input Sampling Frequency vs. Gain Gain 1 2 4 8 to 128 Input Sampling Frequency (fS) fCLKIN/64 (38.4 kHz @ fCLKIN = 2.4576 MHz) 2 × fCLKIN/64 (76.8 kHz @ fCLKIN = 2.4576 MHz) 4 × fCLKIN/64 (76.8 kHz @ fCLKIN = 2.4576 MHz) 8 × fCLKIN/64 (307.2 kHz @ fCLKIN = 2.4576 MHz) BIPOLAR/UNIPOLAR INPUT The analog inputs on the AD7705/AD7706 can accept either unipolar or bipolar input voltage ranges. Bipolar input ranges do not imply that these parts can handle negative voltages on their analog inputs; the analog inputs cannot go more negative than −100 mV to ensure correct operation of these parts. The input channels are fully differential. As a result, on the AD7705, the voltage to which the unipolar and bipolar signals on the AIN(+) input are referenced is the voltage on the respective AIN(−) input. HIGH IMPEDANCE >1G VBIAS SWITCHING FREQUENCY DEPENDS ON fCLKIN AND SELECTED GAIN 10 152 kΩ 75.1 kΩ 34.2 kΩ 16.7 kΩ In buffered mode, the analog inputs look into the high impedance inputs stage of the on-chip buffer amplifier. CSAMP is charged via this buffer amplifier such that source impedances do not affect the charging of CSAMP. This buffer amplifier has an offset leakage current of 1 nA. In this buffered mode, large source impedances result in a small dc offset voltage developed across the source impedance, but not in a gain error. 01166-014 AIN(+) Gain 1 2 4 8 to 128 Figure 14. Unbuffered Analog Input Structure Rev. C | Page 22 of 44 AD7705/AD7706 On the AD7706, the voltages applied to the analog input channels are referenced to the COMMON input. For example, if AIN1(−) is 2.5 V and AD7705 is configured for unipolar operation with a gain of 2 and a VREF of 2.5 V, the input voltage range on the AIN1(+) input is 2.5 V to 3.75 V. If AIN1(−) is 2.5 V and AD7705 is configured for bipolar mode with a gain of 2 and a VREF of 2.5 V, the analog input range on the AIN1(+) input is 1.25 V to 3.75 V (i.e., 2.5 V ± 1.25 V). If AIN1(−) is at GND, the part cannot be configured for bipolar ranges in excess of ±100 mV. Bipolar or unipolar options are chosen by programming the B/U bit of the setup register. This programs the channel for either unipolar or bipolar operation. Programming the channel for either unipolar or bipolar operation does not change the input signal conditioning, it simply changes the data output coding and the points on the transfer function where calibrations occur. REFERENCE INPUT The AD7705/AD7706 reference inputs, REF IN(+) and REF IN(−), provide a differential reference input capability. The commonmode range for these differential inputs is from GND to VDD. The nominal reference voltage, VREF (REF IN(+) − REF IN(−)), for specified operation is 2.5 V for the AD7705/AD7706 operated with a VDD of 5 V, and 1.225 V for the AD7705/AD7706 operated with a VDD of 3 V. The parts are functional with VREF voltages down to 1 V, but performance will be degraded because the output noise, in terms of LSB size, is larger. REF IN(+) must be greater than REF IN(−) for correct operation of the AD7705/AD7706. Both reference inputs provide a high impedance, dynamic load similar to the analog inputs in unbuffered mode. The maximum dc input leakage current is ±1 nA over temperature, and source resistance might result in gain errors on the part. In this case, the sampling switch resistance is 5 kΩ typ, and the reference capacitor, CREF, varies with gain. The sample rate on the reference inputs is fCLKIN/64 and does not vary with gain. For gains of 1 and 2, CREF is 8 pF; for gains of 16, 32, 64, and 128, it is 5.5 pF, 4.25 pF, 3.625 pF, and 3.3125 pF, respectively. The output noise performance outlined in Table 5, Table 6, Table 7, and Table 8 is for an analog input of 0 V, which effectively removes the effect of noise on the reference. To obtain the noise performance shown in the noise tables over the full input range requires a low noise reference source for the AD7705/AD7706. If the reference noise in the bandwidth of interest is excessive, it degrades the performance of the AD7705/AD7706. In applications where the excitation voltage for the bridge transducer on the analog input also derives the reference voltage for the part, the effect of the noise in the excitation voltage is removed because the application is ratiometric. Recommended reference voltage sources for the AD7705/ AD7706 with a VDD of 5 V include the AD780, REF43, and REF192; the recommended reference sources for the AD7705/ AD7706 operated with a VDD of 3 V include the AD589 and AD1580. It is generally recommended to decouple the output of these references to reduce the noise level further. DIGITAL FILTERING The AD7705/AD7706 each contain an on-chip, low-pass digital filter that processes the output of the Σ-Δ modulator. Therefore, the parts not only provide the ADC function, but also provide a level of filtering. There are a number of system differences when the filtering function is provided in the digital domain, rather than in the analog domain. For example, because it occurs after the A/D conversion process, digital filtering can remove noise injected during the conversion process, whereas analog filtering cannot do this. In addition, the digital filter can be made programmable far more readily than the analog filter. Depending on the digital filter design, this provides the user with the update rate. On the other hand, analog filtering can remove noise superimposed on the analog signal before it reaches the ADC. Digital filtering cannot do this, and noise peaks riding on signals near full scale have the potential to saturate the analog modulator and digital filter, even though the average value of the signal is within limits. To alleviate this problem, the AD7705/AD7706 have overrange headroom built into the Σ-Δ modulator and digital filter that allows overrange excursions of 5% above the analog input range. If noise signals are larger than this, consider filtering the analog input, or reducing the input channel voltage so that its full scale is half that of the analog input channel full scale. This provides an overrange capability greater than 100% at the expense of reducing the dynamic range by 1 bit (50%). In addition, the digital filter does not provide any rejection at integer multiples of the digital filter’s sample frequency. However, the input sampling on the part provides attenuation at multiples of the digital filter’s sampling frequency so that the unattenuated bands occur around multiples of the sampling frequency, fS, as defined in Table 23. Thus, the unattenuated bands occur at n × fS (where n = 1, 2, 3 . . .). At these frequencies, there are frequency bands ±f3 dB wide (f3 dB is the cutoff frequency of the digital filter) at either side where noise passes unattenuated to the output. Rev. C | Page 23 of 44 AD7705/AD7706 0 Filter Characteristics –20 The AD7705/AD7706 digital filter is a low-pass filter with a (sinx/x)3 response (also called sinc3). The transfer function for the filter is described in the z-domain by −N 1 1− Z × N 1 − Z −1 –60 –80 GAIN (dB) H (z ) –40 3 –100 –120 –140 –160 and in the frequency domain by –200 3 01166-015 1 sin(N × π × f / f S ) H (f) = × N sin (π × f / f S ) –180 –220 –240 0 where N is the ratio of the modulator rate to the output rate. 60 120 180 240 FREQUENCY (Hz) 300 360 Figure 15. Frequency Response of AD7705 Filter Postfiltering The phase response is defined by the following equation: ∠ H = − 3π (N − 2 ) × f f S Rad Figure 15 shows the filter frequency response for a cutoff frequency of 15.72 Hz, which corresponds to a first filter notch frequency of 60 Hz. The plot is shown from dc to 390 Hz. This response is repeated at either side of the digital filter’s sample frequency and at either side of multiples of the filter’s sample frequency. The response of the filter is similar to that of an averaging filter, but with a sharper roll-off. The output rate for the digital filter corresponds with the positioning of the first notch of the filter’s frequency response. Thus, for Figure 15, where the output rate is 60 Hz, the first notch of the filter is at 60 Hz. The notches of this (sinx/x)3 filter are repeated at multiples of the first notch. The filter provides attenuation of better than 100 dB at these notches. The cutoff frequency of the digital filter is determined by the value loaded to Bit FS0 and Bit FS1 in the clock register. Programming a different cutoff frequency via Bit FS0 and Bit FS1 does not alter the profile of the filter response, but changes the frequency of the notches. The output update of the part and the frequency of the first notch correspond. Because the AD7705/AD7706 contain this on-chip, low-pass filtering, a settling time is associated with step function inputs, and data on the output is invalid after a step change until the settling time has elapsed. The settling time depends on the output rate chosen for the filter. The settling time of the filter to a fullscale step input can be up to four times the output data period. For a synchronized step input using the FSYNC function, the settling time is three times the output data period. The on-chip modulator provides samples at a 19.2 kHz output rate with fCLKIN at 2.4576 MHz. The on-chip digital filter decimates these samples to provide data at an output rate that corresponds to the programmed output rate of the filter. Because the output data rate is higher than the Nyquist criterion, the output rate for a given bandwidth satisfies most application requirements. Some applications, however, might require a higher data rate for a given bandwidth and noise performance. Applications that need this higher data rate will require postfiltering following the digital filtering performed by the AD7705/AD7706. For example, if the required bandwidth is 7.86 Hz, but the required update rate is 100 Hz, data can be taken from the AD7705/AD7706 at the 100 Hz rate, giving a −3 dB bandwidth of 26.2 Hz. Postfiltering can then be applied to reduce the bandwidth and output noise to the 7.86 Hz bandwidth level while maintaining an output rate of 100 Hz. Postfiltering can also be used to reduce the output noise from the devices for bandwidths below 13.1 Hz. At a gain of 128 and a bandwidth of 13.1 Hz, the output rms noise is 450 nV. This is essentially device noise, or white noise. Because the input is chopped, the noise has a primarily flat frequency response. By reducing the bandwidth below 13.1 Hz, the noise in the resultant pass band is reduced. A reduction in bandwidth by a factor of 2 results in a reduction of approximately 1.25 in the output rms noise. This additional filtering results in a longer settling time. Rev. C | Page 24 of 44 AD7705/AD7706 ANALOG FILTERING The digital filter does not provide any rejection at integer multiples of the modulator sample frequency, as outlined earlier. However, due to the part’s high oversampling ratio, these bands occupy only a small fraction of the spectrum, and most broadband noise is filtered. Therefore, the analog filtering requirements in front of the AD7705/AD7706 are considerably reduced vs. a conventional converter without on-chip filtering. In addition, because the parts’ common-mode rejection performance of 100 dB extends to several kHz, common-mode noise in this frequency range is substantially reduced. Depending on the application, however, it might be necessary to provide attenuation of the signal before it reaches the AD7705/ AD7706 to eliminate unwanted frequencies that can pass through the digital filter. It might also be necessary to provide analog filtering in front of the AD7705/AD7706 to ensure that differential noise signals outside the band of interest do not saturate the analog modulator. If passive components are placed in front of the AD7705/ AD7706 in unbuffered mode, care must be taken to ensure that the source impedance is low enough not to introduce gain errors in the system. This significantly limits the amount of passive antialiasing filtering, which can be provided in front of the AD7705/AD7706 when the parts are used in unbuffered mode. However, when the parts are used in buffered mode, large source impedances result in a small dc offset error (a 10 kΩ source resistance causes an offset error of less than 10 μV). Therefore, if the system requires significant source impedances to provide passive analog filtering in front of the AD7705/AD7706, it is recommended to operate the part in buffered mode. CALIBRATION The AD7705/AD7706 provide a number of calibration options that can be programmed via the MD1 and MD0 bits of the setup register. The different calibration options are outlined in the Setup Register (RS2, RS1, RS0 = 0, 0, 1); Power-On/Reset Status: 01 Hex, and Calibration Sequences sections. A calibration cycle can be initiated at any time by writing to these bits of the setup register. Calibration on the AD7705/AD7706 removes offset and gain errors from the devices. A calibration routine should be initiated on these devices whenever there is a change in the ambient operating temperature or supply voltage. It should also be initiated if there is a change in the selected gain, filter notch, or bipolar/unipolar input range. The AD7705/AD7706 offer self-calibration and system calibration facilities. For full calibration to occur on the selected channel, the on-chip microcontroller must record the modulator output for two input conditions: zero-scale point and full-scale point. These points are derived by performing a conversion on the different input voltages provided to the input of the modulator during calibration. As a result, the accuracy of the calibration is only as good as the noise level that it provides in normal mode. The result of the zero-scale calibration conversion is stored in the zero-scale calibration register, and the result of the full-scale calibration conversion is stored in the full-scale calibration register. With these readings, the microcontroller can calculate the offset and the gain slope for the input-to-output transfer function of the converter. Internally, the part works with a resolution of 33 bits to determine the conversion result of 16 bits. Self-Calibration A self-calibration is initiated on the AD7705/AD7706 by writing the appropriate values (0, 1) to the MD1 and MD0 bits of the setup register. In self-calibration mode with a unipolar input range, the zero-scale point used to determine the calibration coefficients is with the inputs of the differential pair internally shorted on the part (i.e., AIN(+) = AIN(−) = internal bias voltage on the AD7705, and AIN = COMMON = internal bias voltage on the AD7706). The PGA is set for the selected gain for this zero-scale calibration conversion, as per the G1 and G0 bits in the communication register. The full-scale calibration conversion is performed at the selected gain on an internally generated voltage of VREF/selected gain. The duration time for the calibration is 6 × 1/output rate. This is composed of 3 × 1/output rate for the zero-scale calibration and 3 × 1/output rate for the full-scale calibration. Then, the MD1 and MD0 bits in the setup register return to 0, 0. This provides the earliest indication that the calibration sequence is complete. The DRDY line goes high when calibration is initiated and does not return low until there is a valid new word in the data register. The duration time from the calibration command being issued to DRDY going low is 9 × 1/output rate. This is composed of 3 × 1/output rate for the zero-scale calibration, 3 × 1/output rate for the full-scale calibration, 3 × 1/output rate for a conversion on the analog input, and some overhead to set up the coefficients correctly. If DRDY is low before (or goes low during) writing the calibration command to the setup register, it can take up to one modulator cycle (MCLK IN/128) before DRDY goes high to indicate that a calibration is in progress. Therefore, DRDY should be ignored for one modulator cycle after the last bit is written to the setup register in the calibration command. For bipolar input ranges in the self-calibrating mode, the sequence is very similar to that outlined in the previous paragraph. In this case, the two points are the same as above, but the shorted inputs point is midscale of the transfer function because the part is configured for bipolar operation. System Calibration System calibration allows the AD7705/AD7706 to compensate for system gain and offset errors, as well as their own internal errors. System calibration performs the same slope factor calculations as self-calibration, but uses voltage values presented by the system to the AIN inputs for the zero- and full-scale points. Full system calibration requires a two-step process, a zero-scale system calibration followed by a full-scale system calibration. Rev. C | Page 25 of 44 AD7705/AD7706 For a full system calibration, the zero-scale point must be presented to the converter first. It must be applied to the converter before the calibration step is initiated and remain stable until the step is complete. Once the zero-scale voltage is set up, a zero-scale system calibration is initiated by writing the appropriate values (1, 0) to the MD1 and MD0 bits of the setup register. The zero-scale system calibration is performed at the selected gain. The duration of the calibration is 3 × 1/output rate. Then, Bit MD1 and Bit MD0 in the setup register return to 0, 0, providing the earliest indication that the calibration sequence is complete. The DRDY line goes high when calibration is initiated and returns low when there is a valid new word in the data register. The duration time from the calibration command being issued to DRDY going low is 4 × 1/output rate, because the part performs a normal conversion on the AIN voltage before DRDY goes low. If DRDY is low before (or goes low during) writing the calibration command to the setup register, it can take up to one modulator cycle (MCLK IN/128) before DRDY goes high to indicate that a calibration is in progress. Therefore, DRDY should be ignored for one modulator cycle after the last bit is written to the setup register in the calibration command. After the zero-scale point is calibrated, the full-scale point is applied to AIN, and the second step of the calibration process is initiated by writing the appropriate values (1, 1) to MD1 and MD0. The full-scale voltage must be set up before the calibration is initiated and must remain stable throughout the calibration step. The full-scale system calibration is performed at the selected gain. The duration of the calibration is 3 × 1/output rate. Then, the MD1 and MD0 bits in the setup register return to 0, 0, providing the earliest indication that the calibration sequence is complete. The DRDY line goes high when calibration is initiated and returns low when there is a valid new word in the data register. The duration time from the calibration command being issued to DRDY going low is 4 × 1/output rate, because the part performs a normal conversion on the AIN voltage before DRDY goes low. If DRDY is low before (or goes low during) writing the calibration command to the setup register, it can take up to one modulator cycle (MCLK IN/128) before DRDY goes high to indicate that calibration is in progress. Therefore, DRDY should be ignored for one modulator cycle after the last bit is written to the setup register in the calibration command. In unipolar mode, the system calibration is performed between the two endpoints of the transfer function. In bipolar mode, it is performed between midscale (zero differential voltage) and positive full scale. The fact that the system calibration involves two steps offers another feature. After the sequence of a full system calibration is complete, additional offset or gain calibrations can be performed individually to adjust the system zero reference point or the system gain. Calibrating one of the parameters, either system offset or system gain, does not affect the other parameter. When the part is used in unbuffered mode, system calibration can be used to remove errors from source impedances on the analog input. A simple R-C antialiasing filter on the front end can introduce a gain error on the analog input voltage, but the system calibration can be used to remove this error. Span and Offset Limits Whenever the system calibration mode is used, there are limits on the amount of offset and span that can be accommodated. The overriding requirement for determining the amount of offset and gain that can be accommodated by the part is that the positive full-scale calibration limit is < 1.05 × VREF/gain. This allows the input range to go 5% above the nominal range. The built-in headroom in the AD7705/AD7706 analog modulator ensures that the parts operate correctly with a positive full-scale voltage that is 5% beyond the nominal. The range of input span in both the unipolar and bipolar modes has a minimum value of 0.8 × VREF/gain and a maximum value of 2.1 × VREF/gain. However, when determining the span, which is the difference between the bottom and top of the devices’ input range, the user must take into account the limitation on the positive full-scale voltage. The amount of offset that can be accommodated depends on whether the unipolar or bipolar mode is used, and the user must also take into account the limitation on the positive full-scale voltage. In unipolar mode, there is considerable flexibility in handling negative offsets with respect to AIN(−) on the AD7705, and with respect to COMMON on the AD7706. In both unipolar and bipolar modes, the range of positive offsets that can be handled by the part depends on the selected span. Therefore, in determining the limits for system zero-scale and full-scale calibrations, the user must ensure that the offset range plus the span range does not exceed 1.05 × VREF/gain. If the part is used in unipolar mode with a required span of 0.8 × VREF/gain, the offset range that the system calibration can handle is –1.05 × VREF/gain to +0.25 × VREF/gain. If the part is used in unipolar mode with a required span of VREF/gain, the offset range that the system calibration can handle is −1.05 × VREF/gain to +0.05 × VREF/gain. Similarly, if the part is used in unipolar mode and required to remove an offset of 0.2 × VREF/gain, the maximum span range that the system calibration can handle is 0.85 × VREF/gain. Rev. C | Page 26 of 44 AD7705/AD7706 1.05 × VREF/GAIN Power-Up and Calibration UPPER LIMIT ON AD7705 INPUT VOLTAGE AD7705/AD7706 INPUT RANGE (0.8 × VREF/GAIN TO 2.1 × VREF/GAIN) Upon power-up, the AD7705/AD7706 internally reset, setting the contents of the internal registers to a known state. Default values are loaded to all registers after a power-on or reset. The default values contain nominal calibration coefficients for the calibration registers. However, to ensure correct calibration for the devices, a calibration routine should be performed after power-up. GAIN CALIBRATIONS EXPAND OR CONTRACT THE AD7705/AD7706 INPUT RANGE –0V DIFFERENTIAL NOMINAL ZERO SCALE POINT OFFSET CALIBRATIONS MOVE INPUT RANGE UP OR DOWN –1.05 × VREF/GAIN 01166-016 LOWER LIMIT ON AD7705/AD7706 INPUT VOLTAGE Figure 16. Span and Offset Limits If the part is used in bipolar mode with a required span of ±0.4 × VREF/gain, the offset range that the system calibration can handle is –0.65 × VREF/gain to +0.65 × VREF/gain. If the part is used in bipolar mode with a required span of ±VREF/gain, the offset range that the system calibration can handle is –0.05 × VREF/gain to +0.05 × VREF/gain. Similarly, if the part is used in bipolar mode and required to remove an offset of ±0.2 × VREF/gain, the maximum span range that the system calibration can handle is ±0.85 × VREF/gain. The power dissipation and temperature drift of the AD7705/ AD7706 are low, and no warm-up time is required before the initial calibration is performed. However, if an external reference is used, it must be stabilized before calibration is initiated. Similarly, if the clock source for the part is generated from a crystal or resonator across the MCLK pins, the start-up time for the oscillator circuit should elapse before a calibration is initiated on the parts (see Figure 11). Rev. C | Page 27 of 44 AD7705/AD7706 THEORY OF OPERATION CLOCKING AND OSCILLATOR CIRCUIT The AD7705/AD7706 each require a master clock input, which can be an external CMOS-compatible clock signal applied to the MCLK IN pin with the MCLK OUT pin left unconnected. Alternatively, a crystal or ceramic resonator of the correct frequency can be connected between MCLK IN and MCLK OUT, as shown in Figure 17. In this case, the clock circuit functions as an oscillator, providing the clock source for the part. The input sampling frequency, modulator sampling frequency, –3 dB frequency, output update rate, and calibration time are directly related to the master clock frequency, fCLKIN. Reducing the master clock frequency by a factor of two halves the above frequencies and update rate and doubles the calibration time. The current drawn from the VDD power supply is also related to fCLKIN. Reducing fCLKIN by a factor of two halves the digital part of the total VDD current, but does not affect the current drawn by the analog circuitry. CRYSTAL OR CERAMIC RESONATOR MCLK IN C1 AD7705/AD7706 01166-017 MCLK OUT C2 Figure 17. Crystal/Resonator Connection for the AD7705/AD7706 Using the part with a crystal or ceramic resonator between the MCLK IN pin and MCLK OUT pin generally causes more current to be drawn from VDD than does clocking the part from a driven clock signal at the MCLK IN pin. This is because the on-chip oscillator circuit is active in the case of the crystal or ceramic resonator. Therefore, the lowest possible current on the AD7705/AD7706 is achieved with an externally applied clock at the MCLK IN pin with MCLK OUT unconnected, unloaded, and disabled. The amount of additional current taken by the oscillator depends on a number of factors. For example, the larger the value of the capacitor (C1 and C2) placed on the MCLK IN and MCLK OUT pins, the larger the current consumption on the AD7705/AD7706. To avoid unnecessarily consuming current, care should be taken not to exceed the capacitor values recommended by the crystal and ceramic resonator manufacturers. Typical values for C1 and C2 are recommended by crystal or ceramic resonator manufacturers, usually in the range of 30 pF to 50 pF. If the capacitor values on MCLK IN and MCLK OUT are kept in this range, they do not result in any excessive current. Another factor that influences the current is the effective series resistance (ESR) of the crystal that appears between the MCLK IN and MCLK OUT pins of the AD7705/ AD7706. As a general rule, the lower the ESR value, the lower the current taken by the oscillator circuit. When operating with a clock frequency of 2.4576 MHz, there is a 50 μA difference in the current between an externally applied clock and a crystal resonator operated with a VDD of 3 V. With VDD = 5 V and fCLKIN = 2.4576 MHz, the typical current increases by 250 μA for a crystal- or resonator-supplied clock vs. an externally applied clock. The ESR values for crystals and resonators at this frequency tend to be low, and, as a result, there tends to be little difference between different crystal and resonator types. When operating with a clock frequency of 1 MHz, the ESR value for different crystal types varies significantly. As a result, the current drain varies across crystal types. When using a crystal with an ESR of 700 Ω, or when using a ceramic resonator, the increase in the typical current over an externally applied clock is 20 μA with VDD = 3 V, and 200 μA with VDD = 5 V. When using a crystal with an ESR of 3 kΩ, the increase in the typical current over an externally applied clock is 100 μA with VDD = 3 V, but 400 μA with VDD = 5 V. There is a start-up time before the on-chip oscillator circuit oscillates at its correct frequency and voltage levels. Typical startup times with VDD = 5 V are 6 ms using a 4.9512 MHz crystal, 16 ms with a 2.4576 MHz crystal, and 20 ms with a 1 MHz crystal oscillator. Start-up times are typically 20% slower when a 3 V power supply is used. With 3 V supplies, depending on the loading capacitances on the MCLK pins, a 1 MΩ feedback resistor might be required across the crystal or resonator to keep the start-up times around 20 ms. The AD7705/AD7706 master clock appears on the MCLK OUT pin of the device. The maximum recommended load on this pin is 1 CMOS load. When using a crystal or ceramic resonator to generate the AD7705/AD7706 clock, it might be desirable to use this clock as the clock source for the system. In this case, it is recommended that the MCLK OUT signal be buffered with a CMOS buffer before being applied to the rest of the circuit. SYSTEM SYNCHRONIZATION The FSYNC bit of the setup register allows the user to reset the modulator and digital filter without affecting the setup conditions on the part. This allows the user to start gathering samples of the analog input at a known point in time, that is, when the FSYNC changes from 1 to 0. With a 1 in the FSYNC bit of the setup register, the digital filter and analog modulator are held in a known reset state, and the part does not process input samples. When a 0 is written to the FSYNC bit, the modulator and filter are taken out of this reset state, and the part resumes gathering samples on the next master clock edge. Rev. C | Page 28 of 44 AD7705/AD7706 The FSYNC input can also be used as a software start convert command, allowing the AD7705/AD7706 to be operated in a conventional converter fashion. In this mode, writing to the FSYNC bit starts conversion, and the falling edge of DRDY indicates when conversion is complete. The disadvantage of this scheme is that the settling time of the filter must be taken into account for every data register update; therefore, the rate at which the data register is updated is three times slower in this mode. Because the FSYNC bit resets the digital filter, the full settling time of 3 × 1/output rate must elapse before a new word is loaded to the output register. If the DRDY signal is low when FSYNC goes to 0, the DRDY signal is not reset to high by the FSYNC command, because the AD7705/AD7706 recognize that there is a word in the data register that has not been read. The DRDY line stays low until an update of the data register takes place, at which time it goes high for 500 × tCLKIN before returning low again. A read from the data register resets the DRDY signal high, and it does not return low until the settling time of the filter has elapsed and there is a valid new word in the data register. If the DRDY line is high when the FSYNC command is issued, the DRDY line does not return low until the settling time of the filter has elapsed. RESET INPUT The RESET input on the AD7705/AD7706 resets the logic, digital filter, analog modulator, and on-chip registers to their default states. DRDY is driven high, and the AD7705/AD7706 ignore all communication to their registers while the RESET input is low. When the RESET input returns high, the AD7705/AD7706 start to process data, and DRDY returns low in 3 × 1/output rate, indicating a valid new word in the data register. However, the AD7705/AD7706 operate with their default setup conditions after a reset, and it is generally necessary to set up all registers and perform a calibration after a RESET command. The AD7705/AD7706 on-chip oscillator circuit continues to function even when the RESET input is low, and the master clock signal continues to be available on the MCLK OUT pin. Therefore, in applications where the system clock is provided by the AD7705/AD7706 clock, the AD7705/AD7706 produce an uninterrupted master clock during a RESET command. STANDBY MODE The STBY bit in the communication register of the AD7705/ AD7706 allows the user to place the part in a power-down mode when it is not required to provide conversion results. The AD7705/AD7706 retain the contents of their on-chip registers, including the data register, while in standby mode. When released from standby mode, the parts start to process data, and a new word is available in the data register in 3 × 1/output rate from when a 0 is written to the STBY bit. The STBY bit does not affect the digital interface, nor does it affect the status of the DRDY line. If DRDY is high when the STBY bit is brought low, it remains high until there is a valid new word in the data register. If DRDY is low when the STBY bit is brought low, it remains low until the data register is updated, at which time the DRDY line returns high for 500 × tCLKIN before returning low again. If DRDY is low when the part enters standby mode, indicating a valid unread word in the data register, the data register can be read while the part is in standby. At the end of this read operation, DRDY is reset to high. Placing the part in standby mode reduces the total current to 9 μA typical with VDD = 5 V, and 4 μA with VDD = 3 V when the part is operated from an external master clock, provided that this master clock has stopped. If the external clock continues to run in standby mode, the standby current increases to 150 μA typical with 5 V supplies, and 75 μA typical with 3.3 V supplies. If a crystal or ceramic resonator is used as the clock source, the total current in standby mode is 400 μA typical with 5 V supplies, and 90 μA with 3.3 V supplies. This is because the on-chip oscillator circuit continues to run when the part is in standby mode. This is important in applications where the system clock is provided by the AD7705/AD7706 clock so that the AD7705/AD7706 produce an uninterrupted master clock in standby mode. ACCURACY Σ-Δ ADCs, like VFCs and other integrating ADCs, do not contain a source of nonmonotonicity and inherently offer no missing codes performance. The AD7705/AD7706 achieve excellent linearity by using high quality, on-chip capacitors that have a very low capacitance/voltage coefficient. The devices also achieve low input drift by using chopper-stabilization techniques in their input stage. To ensure excellent performance over time and temperature, the AD7705/AD7706 use digital calibration techniques that minimize offset and gain error. DRIFT CONSIDERATIONS The AD7705/AD7706 use chopper-stabilization techniques to minimize input offset drift. Charge injection in the analog switches and dc-leakage currents at the sampling node are the primary sources of offset voltage drift in the converter. The dc input leakage current is essentially independent of the selected gain. Gain drift within the converter primarily depends on the temperature tracking of the internal capacitors. It is not affected by leakage currents. Measurement errors due to offset drift or gain drift can be eliminated at any time by recalibrating the converter. Using the system calibration mode also minimizes offset and gain errors in the signal conditioning circuitry. Integral and differential linearity errors are not significantly affected by temperature changes. Rev. C | Page 29 of 44 AD7705/AD7706 POWER SUPPLIES GROUNDING AND LAYOUT The AD7705/AD7706 operate with VDD power supplies between 2.7 V and 5.25 V. Although the latch-up performance of the AD7705/AD7706 is good, it is important that power is applied to the AD7705/AD7706 before signals are applied at the REF IN, AIN, or logic input pins to avoid excessive currents. If this is not possible, the current through these pins should be limited. If separate supplies are used for the AD7705/AD7706 and the system digital circuitry, the AD7705/AD7706 should be powered up first. If it is not possible to guarantee this, current-limiting resistors should be placed in series with the logic inputs to limit the current. The latch-up current is greater than 100 mA. Because the analog inputs and reference input are differential, most of the voltages in the analog modulator are common-mode voltages. The excellent common-mode rejection of the parts removes common-mode noise on these inputs. The digital filter provides rejection of broadband noise on the power supplies, except at integer multiples of the modulator sampling frequency. The digital filter also removes noise from the analog and reference inputs, provided that those noise sources do not saturate the analog modulator. As a result, the AD7705/AD7706 are more immune to noise interference than conventional high resolution converters. However, because the resolutions of the AD7705/ AD7706 are so high and the noise levels from the AD7705/ AD7706 are so low, care must be taken with regard to grounding and layout. SUPPLY CURRENT The current consumption on the AD7705/AD7706 is specified for supplies in the range of 2.7 V to 3.3 V and 4.75 V to 5.25 V. The parts operate over a 2.7 V to 5.25 V supply range, and the IDD changes as the supply voltage varies over this range. There is an internal current boost bit on the AD7705/AD7706 that is set internally in accordance with the operating conditions. This affects the current drawn by the analog circuitry within these devices. Minimum power consumption is achieved when the AD7705/AD7706 are operated with an fCLKIN of 1 MHz, or at gains of 1 to 4 with fCLKIN = 2.4575 MHz, because the internal boost bit reduces the analog current consumption. Figure 18 shows the variation of the typical IDD with VDD voltage for both a 1 MHz crystal oscillator and a 2.4576 MHz crystal oscillator at 25°C. The AD7705/AD7706 are operated in unbuffered mode. The relationship shows that the IDD is minimized by operating the part with lower VDD voltages. IDD on the AD7705/AD7706 is also minimized by using an external master clock, or by optimizing external components when using the on-chip oscillator circuit. Figure 6, Figure 7, Figure 9, and Figure 10 show variations in IDD with gain, VDD, and clock frequency using an external clock. 1600 1400 1200 MCLK IN = CRYSTAL OSCILLATOR TA = 25°C UNBUFFERED MODE GAIN = +128 fCLK = 2.4576MHz 800 600 fCLK = 1MHz 400 200 0 2.5 01166-018 IDD (μA) 1000 3.0 3.5 4.0 VDD 4.5 Figure 18. IDD vs. Supply Voltage 5.0 5.5 The printed circuit board that houses the AD7705/AD7706 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. This facilitates the use of ground planes that can be separated easily. A minimum etch technique is generally best for ground planes, because it provides the best shielding. Digital and analog ground planes should only be joined in one place to avoid ground loops. If the AD7705/AD7706 are in a system where multiple devices require AGND-to-DGND connections, the AGND-to-DGND connection should only be made at one point, a star ground point, which should be established as close as possible to the AD7705/AD7706 GND. Avoid running digital lines under the device, because they couple noise onto the die. The analog ground plane should be allowed to run under the AD7705/AD7706 to avoid noise coupling. The power supply lines to the AD7705/AD7706 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals, such as clock signals, should be shielded with digital ground to avoid radiating noise to other sections of the board, and clock signals should never be run near the analog inputs. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feedthrough through the board. Using a microstrip technique works best, but it is not always possible to use this method with a double-sided board. In this technique, the component side of the board is dedicated to ground planes, and signals are placed on the solder side. Good decoupling is important when using high resolution ADCs. All analog supplies should be decoupled with 10 μF tantalum in parallel with 0.1 μF ceramic capacitors to GND. To achieve the best from these decoupling components, place them as close as possible to the device, ideally right up against the device. All logic chips should be decoupled with 0.1 μF disc ceramic capacitors to DGND. Rev. C | Page 30 of 44 AD7705/AD7706 EVALUATING THE PERFORMANCE The recommended layout for the AD7705/AD7706 is outlined in their associated evaluations. Each evaluation board package includes a fully assembled and tested evaluation board, documentation, software for controlling the board over the printer port of a PC, and software for analyzing its performance on a PC. Noise levels in the signals applied to the AD7705/AD7706 can also affect performance of the parts. The AD7705/AD7706 software evaluation packages allow the user to evaluate the true performance of the parts independently of the analog input signals. For the AD7705, the scheme involves using a test mode with the inputs internally shorted together to provide a zero differential voltage for the analog modulator. External to the AD7705, the AIN1(−) input should be connected to a voltage that is within the allowable common-mode range of the part. Similarly, on the AD7706 for evaluation purposes, the COMMON input should be connected to a voltage within its allowable common-mode range. This scheme should be used after a calibration is performed on the parts. DIGITAL INTERFACE As previously outlined, the AD7705/AD7706 programmable functions are controlled using a set of on-chip registers. Data is written to these registers via the serial interface, which also provides read access to the on-chip registers. All communication to the parts must start with a write operation to the communication register. After a power-on or reset, the devices expect a write to their communication registers. The data written to these registers determine whether the next operation is a read or write operation and to which register this operation occurs. Therefore, write access to a register on either part starts with a write operation to the communication register, followed by a write to the selected register. Likewise, a read operation from any register, including the output data register, starts with a write operation to the communication register, followed by a read operation from the selected register. The AD7705/AD7706 serial interfaces each consist of five signals: CS, SCLK, DIN, DOUT, and DRDY. The DIN line is used for transferring data into the on-chip registers, and the DOUT line is used for accessing data from the on-chip registers. SCLK is the serial clock input for the device, and all data transfers on either DIN or DOUT take place with respect to this SCLK signal. The DRDY line is used as a status signal to indicate when data is ready to be read from the AD7705/AD7706 data registers. DRDY goes low when a new data-word is available in the output register. It is reset high when a read operation from the data register is complete. It also goes high prior to updating the output register, indicating not to read from the device, to ensure that a data read is not attempted while the register is updated. CS is used to select the device. It can be used to decode the AD7705/AD7706 in systems where a number of parts are connected to the serial bus. Figure 19 and Figure 20 show timing diagrams for interfacing to the AD7705/AD7706, with CS used to decode the parts. Figure 19 shows a read operation from the AD7705/AD7706 output shift register, and Figure 20 shows a write operation to the input shift register. It is possible to read the same data twice from the output register, even though the DRDY line returns high after the first read operation. Care must be taken, however, to ensure that the read operation is complete before the next output update takes place. The AD7705/AD7706 serial interface can operate in 3-wire mode by tying the CS input low. In this case, the SCLK, DIN, and DOUT lines are used to communicate with the AD7705/ AD7706, and the status of DRDY can be obtained by interrogating the MSB of the communication register. This scheme is suitable for interfacing to microcontrollers. If CS is required as a decoding signal, it can be generated from a port bit. For microcontroller interfaces, it is recommended that the SCLK idles high between data transfers. The AD7705/AD7706 can also be operated with CS used as a frame synchronization signal. This scheme is suitable for DSP interfaces. In this case, the first bit (MSB) is effectively clocked out by CS, because CS normally occurs after the falling edge of SCLK in DSP interfaces. The SCLK can continue to run between data transfers, provided that the timing numbers are obeyed. The serial interface can be reset by exercising the RESET input. It can also be reset by writing a series of 1s on the DIN input. If Logic 1 is written to the AD7705/AD7706 DIN line for at least 32 serial clock cycles, the serial interface is reset. This ensures that in 3-wire systems, if the interface is lost via either a software error or a glitch in the system, it can be reset to a known state. This state returns the interface to where the AD7705/AD7706 are expecting a write operation to their communication registers. This operation in itself does not reset the contents of any registers, but it is advisable to set up all registers again, because the information written to the registers is unknown due to the interface being lost. Some microprocessor or microcontroller serial interfaces have a single serial data line. In this case, it is possible to connect the AD7705/AD7706 DATA OUT and DATA IN lines together and connect them to the single data line of the processor. A 10 kΩ pull-up resistor should be used on this single data line. In this case, if the interface is lost, the procedure to reset it back to a known state is somewhat different than previously described because the read and write operations share the same line. Instead, a read operation of 24 serial clocks is required, followed by a write operation where Logic 1 is written for at least 32 serial clock cycles to ensure that the serial interface resets to a known state. Rev. C | Page 31 of 44 AD7705/AD7706 DRDY t10 t3 CS t4 t8 t6 SCLK DOUT 01166-019 t9 t7 t5 LSB MSB Figure 19. Read Cycle Timing Diagram CS t11 t16 t14 SCLK DIN t13 t15 LSB MSB Figure 20. Write Cycle Timing Diagram Rev. C | Page 32 of 44 01166-020 t12 AD7705/AD7706 CONFIGURING THE AD7705/AD7706 The AD7705/AD7706 contain six on-chip registers that the user can access via the serial interface. Communication with any of these registers is initiated by first writing to the communication register. Figure 21 outlines a flowchart of the sequence used to configure registers after a power-up or reset on the AD7705; similar procedures apply to the AD7706. The flowchart also shows two read options—one polls the DRDY pin, and the other interrogates the DRDY pin. In addition, Figure 21 shows a series of words that should be written to the registers for the following operating conditions: Gain 1, no filter sync, bipolar mode, buffer off, clock of 4.9512 MHz, and output rate of 50 Hz. START POWER-ON/RESET FOR AD7705 CONFIGURE & INITIALIZE μC/μP SERIAL PORT WRITE TO COMMUNICATIONS REGISTER SELECTING CHANNEL & SETTING UP NEXT OPERATION TO BE A WRITE TO THE CLOCK REGISTER (20 HEX) WRITE TO CLOCK REGISTER SETTING THE CLOCK BITS IN ACCORDANCE WITH THE APPLIED MASTER CLOCK SIGNAL AND SELECT UPDATE RATE FOR SELECTED CHANNEL (0C HEX) WRITE TO COMMUNICATIONS REGISTER SELECTING CHANNEL & SETTING UP NEXT OPERATION TO BE A WRITE TO THE SETUP REGISTER (10 HEX) WRITE TO SETUP REGISTER CLEARING F SYNC, SETTING UP GAIN, OPERATING CONDITIONS & INITIATING A SELF-CALIBRATION ON SELECTED CHANNEL (40 HEX) POLL DRDY PIN NO WRITE TO COMMUNICATIONS REGISTER SETTING UP NEXT OPERATION TO BE A READ FROM THE COMMUNICATIONS REGISTER (08 HEX) DRDY LOW? YES READ FROM COMMUNICATIONS REGISTER WRITE TO COMMUNICATIONS REGISTER SETTING UP NEXT OPERATION TO BE A READ FROM THE DATA REGISTER (38 HEX) POLL DRDY BIT OF COMMUNICATIONS REGISTER READ FROM DATA REGISTER NO DRDY LOW? YES WRITE TO COMMUNICATIONS REGISTER SETTING UP NEXT OPERATION TO BE A READ FROM THE DATA REGISTER (38 HEX) 01166-021 READ FROM DATA REGISTER Figure 21. Flowchart for Setting Up and Reading from the AD7705 Rev. C | Page 33 of 44 AD7705/AD7706 MICROCOMPUTER/MICROPROCESSOR INTERFACING The flexible serial interface of the AD7705/AD7706 allows easy interfacing to most microcomputers and microprocessors. The flowchart in Figure 21 outlines the sequence to follow when interfacing a microcontroller or microprocessor to the AD7705/AD7706. Figure 22 through Figure 24 show typical interface circuits. The second scheme is to use an interrupt-driven system, in which case the DRDY output is connected to the IRQ input of the 68HC11. For interfaces that require control of the CS input on the AD7705/AD7706, a port bit of the 68HC11 (such as PC1) that is configured as an output can be used to drive the CS input. VDD VDD The serial interface is capable of operating from three wires and is compatible with SPI interface protocols. The 3-wire operation makes these parts ideal for an isolated system in which minimizing the number of interface lines minimizes the number of opto-isolators required in the system. The serial clock input is a Schmitt-triggered input to accommodate slow edges from optocouplers. The rise and fall times of other digital inputs to the AD7705/AD7706 should be no longer than 1 μs. Because some registers on the AD7705/AD7706 are only 8 bits long, successive write operations to two of these registers can be handled as a single 16-bit data transfer. For example, to update the setup register, the processor must write to the communication register to indicate that the next operation is a write to the setup register, and then write 8 bits to the setup register. This can be done in a single 16-bit transfer, because once the eight serial clocks of the write operation to the communication register are complete, the part immediately sets up for a write operation to the setup register. RESET 68HC11 SCK SCLK MISO DOUT MOSI DIN CS 01166-022 Most of the registers on the AD7705/AD7706 are 8-bit registers, which facilitates easy interfacing to the 8-bit serial ports of microcontrollers. The data register on the AD7705/AD7706 is 16 bits, and the offset and gain registers are 24-bit registers, but data transfers to these registers can consist of multiple 8-bit transfers to the serial port of the microcontroller. DSP processors and microprocessors generally transfer 16 bits of data in a serial data operation. Some of these processors, such as the ADSP-2105, have the facility to program the number of cycles in a serial transfer. This allows the user to tailor the number of bits in any transfer to match the length of the required register in the AD7705/AD7706. AD7705/AD7706 SS Figure 22. AD7705/AD7706-to-68HC11 Interface The 68HC11 is configured in master mode with its CPOL and CPHA bits set to Logic 1. When the 68HC11 is configured like this, its SCLK line idles high between data transfers. The AD7705/ AD7706 are not capable of a full duplex operation. If the AD7705/ AD7706 are configured for a write operation, no data appears on the DOUT lines, even when the SCLK input is active. Similarly, if the AD7705/AD7706 are configured for a read operation, data presented to the part on the DIN line is ignored, even when SCLK is active. Coding for an interface between the 68HC11 and the AD7705/ AD7706 is given in the C Code for Interfacing AD7705 to 68HC11 section. In this example, the DRDY output line of the AD7705 is connected to the PC0 port bit of the 68HC11 and is polled to determine its status. AD7705/AD7706-to-68HC11 Interface VDD 8XC51 Rev. C | Page 34 of 44 P3.0 RESET DOUT DIN P3.1 SCLK CS 01166-023 Figure 22 shows an interface between the AD7705/AD7706 and the 68HC11 microcontroller. The diagram shows the minimum (3-wire) interface with CS on the AD7705/AD7706 hardwired low. In this scheme, the DRDY bit of the communication register is monitored to determine when the data register is updated. An alternative scheme, which increases the number of interface lines to four, is to monitor the DRDY output line from the AD7705/ AD7706. Monitoring the DRDY line can be done in two ways. First, DRDY can be connected to a 68HC11 port bit (such as PC0) that is configured as an input. This port bit is then polled to determine the status of DRDY. VDD AD7705/AD7706 Figure 23. AD7705/AD7706-to-8XC51 Interface AD7705/AD7706 AD7705/AD7706-to-8051 Interface AD7705/AD7706-to-ADSP-2103/ADSP-2105 Interface An interface circuit between the AD7705/AD7706 and the 8XC51 microcontroller is shown in Figure 23. The diagram shows the minimum number of interface connections with CS on the AD7705/AD7706 hardwired low. In the case of the 8XC51 interface, the minimum number of interconnects is two. In this scheme, the DRDY bit of the communication register is monitored to determine when the data register is updated. The alternative scheme, which increases the number of interface lines to three, is to monitor the DRDY output line from the AD7705/AD7706. Monitoring the DRDY line can be done in two ways. First, DRDY can be connected to a 8XC51 port bit (such as P1.0) that is configured as an input. This port bit is then polled to determine the status of DRDY. The second scheme is to use an interruptdriven system, in which case the DRDY output is connected to the INT1 input of the 8XC51. For interfaces that require control of the CS input on the AD7705/AD7706, a port bit of the 8XC51 (such as P1.1) that is configured as an output can be used to drive the CS input. The 8XC51 is configured in Mode 0 serial interface mode. Its serial interface contains a single data line. As a result, the DOUT and DIN pins of the AD7705/ AD7706 should be connected together with a 10 kΩ pull-up resistor. The serial clock on the 8XC51 idles high between data transfers. During a write operation, the 8XC51 outputs the LSB first. Because the AD7705/AD7706 expect the MSB first, the data must be rearranged before being written to the output serial register. Similarly, during a read operation, the AD7705/ AD7706 output the MSB first, and the 8XC51 expects the LSB first. Therefore, the data read into the serial buffer must be rearranged before the correct data-word from the AD7705/ AD7706 is available in the accumulator. Figure 24 shows an interface between the AD7705/AD7706 and the ADSP-2103/ADSP-2105 DSP processor. In the interface shown, the DRDY bit of the communication register is monitored to determine when the data register is updated. The alternative scheme is to use an interrupt-driven system, in which case the DRDY output is connected to the IRQ2 input of the ADSP-2103/ ADSP-2105. The serial interface of the ADSP-2103/ADSP-2105 is set up for alternate framing mode. The RFS and TFS pins of the ADSP-2103/ADSP-2105 are configured as active low outputs, and the ADSP-2103/ADSP-2105 serial clock line, SCLK, is configured as an output. The CS for the AD7705/AD7706 is active when either the RFS or TFS outputs from the ADSP-2103/ ADSP-2105 are active. The serial clock rate on the ADSP-2103/ ADSP-2105 should be limited to 3 MHz to ensure correct operation with the AD7705/AD7706. VDD ADSP-2103/ ADSP-2105 AD7705/AD7706 CODE FOR SETTING UP THE AD7705/AD7706 The following section shows a set of read and write routines in C code for interfacing the 68HC11 microcontroller to the AD7705. The sample program sets up the various registers on the AD7705 and reads 1000 samples from one channel into the 68HC11. The setup conditions on the part are the same as those outlined for the flowchart of Figure 21. In the example code given here, the DRDY output is polled to determine if a new valid word is available in the data register. The same sequence is applicable for the AD7706. The sequence of events in this program are as follows: 1. Write to the communication register, selecting Channel 1 as the active channel and setting the next operation to be a write to the clock register. 2. Write to the clock register, setting the CLKDIV bit, which divides the external clock internally by two. This assumes that the external crystal is 4.9512 MHz. The update rate is selected to be 50 Hz. 3. Write to the communication register selecting Channel 1 as the active channel and setting the next operation to be a write to the setup register. 4. Write to the setup register, setting the gain to 1, setting bipolar mode, buffer off, clearing the filter synchronization, and initiating a self-calibration. 5. Poll the DRDY output. 6. Read the data from the data register. 7. Repeat Steps 5 and 6 (loop) until the specified number of samples has been taken from the selected channel. RESET RFS CS TFS DR DOUT DT DIN SCLK 01166-024 SCLK Figure 24. AD7705/AD7706-to-ADSP-2103/ADSP-2105 Interface Rev. C | Page 35 of 44 AD7705/AD7706 C Code for Interfacing AD7705 to 68HC11 #include #include #define NUM_SAMPLES 1000 /* change the number of data samples */ #define MAX_REG_LENGTH 2 /* this says that the max length of a register is 2 bytes */ Writetoreg (int); Read (int,char); char *datapointer = store; char store[NUM_SAMPLES*MAX_REG_LENGTH + 30]; void main() { /* the only pin that is programmed here from the 68HC11 is the /CS and this is why the PC2 bit of PORTC is made as an output */ char a; DDRC = 0x04; /* PC2 is an output the rest of the port bits are inputs */ PORTC | = 0x04; /* make the /CS line high */ Writetoreg(0x20); /* Active Channel is Ain1(+)/Ain1(−), next operation as write to the clock register */ Writetoreg(0x0C); /* master clock enabled, 4.9512MHz Clock, set output rate to 50Hz*/ Writetoreg(0x10); /* Active Channel is Ain1(+)/Ain1(−), next operation as write to the setup register */ Writetoreg(0x40); /* gain = 1, bipolar mode, buffer off, clear FSYNC and perform a Self Calibration*/ while(PORTC & 0x10); /* wait for /DRDY to go low */ for(a=0;a