AD7952BSTZ

14-Bit, 1 MSPS, Differential, Programmable Input PulSAR® ADC AD7952 Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAM TEMP REFBUFIN REF REFGND VCC VEE DVDD AGND AVDD SERIAL CONFIGURATION 14 PORT PDBUF SWITCHED CAP DAC IN– OGND SERIAL DATA PORT REF IN+ OVDD AD7952 REF AMP PDREF DGND BYTESWAP PARALLEL INTERFACE CLOCK CNVST OB/2C BUSY PD CONTROL LOGIC AND CALIBRATION CIRCUITRY RESET RD CS WARP IMPULSE BIPOLAR TEN Figure 1. Table 1. 48-Lead PulSAR Selection 100 to 250 (kSPS) 500 to 570 (kSPS) 570 to 1000 (kSPS) Input Type Res (Bits) Bipolar 14 AD7951 Differential Bipolar 14 AD7952 Process controls Medical instruments High speed data acquisition Digital signal processing Instrumentation Spectrum analysis ATE Unipolar 16 Bipolar 16 AD7610 AD7663 AD7665 AD7612 AD7671 GENERAL DESCRIPTION Differential Unipolar 16 AD7675 AD7676 AD7677 APPLICATIONS AD7651 >1000 kSPS AD7653 AD7660 AD7650 AD7661 AD7652 AD7667 AD7664 AD7666 The AD7952 is a 14-bit, charge redistribution, successive approximation register (SAR) architecture analog-to-digital converter (ADC) fabricated on Analog Devices, Inc.’s iCMOS high voltage process. The device is configured through hardware or via a dedicated write-only serial configuration port for input range and operating mode. The AD7952 contains a high speed 14-bit sampling ADC, an internal conversion clock, an internal reference (and buffer), error correction circuits, and both serial and parallel system interface ports. A falling edge on CNVST samples the fully differential analog inputs on IN+ and IN−. The AD7952 features four different analog input ranges and three different sampling modes: warp mode for the fastest throughput, normal mode for the fastest asynchronous throughput, and impulse mode where power is scaled with throughput. Operation is specified from −40°C to +85°C. Rev. A D[13:0] SER/PAR 06589-001 Multiple pins/software-programmable input ranges +5 V (10 V p-p), +10 V (20 V p-p), ±5 V (20 V p-p), ±10 V (40 V p-p) Pins or serial SPI®-compatible input ranges/mode selection Throughput 1 MSPS (warp mode) 800 kSPS (normal mode) 670 kSPS (impulse mode) 14-bit resolution with no missing codes INL: ±0.3 LSB typical, ±1 LSB maximum (±61 ppm of FSR) SNR: 85 dB @ 2 kHz iCMOS® process technology 5 V internal reference: typical drift 3 ppm/°C; TEMP output No pipeline delay (SAR architecture) Parallel (14- or 8-bit bus) and serial 5 V/3.3 V interface SPI-/QSPI™-/MICROWIRE™-/DSP-compatible Power dissipation 235 mW @ 1 MSPS 10 mW @ 1 kSPS 48-lead LQFP and 48-lead LFCSP (7 mm × 7 mm) AD7621 AD7622 AD7623 Simultaneous/ Multichannel Unipolar 16 AD7654 AD7655 Differential Unipolar 18 AD7678 Differential Bipolar 18 AD7631 AD7679 AD7674 AD7641 AD7643 AD7634 Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2007–2012 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD7952 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1  Driver Amplifier Choice ........................................................... 21  Applications ....................................................................................... 1  Voltage Reference Input/Output .............................................. 22  General Description ......................................................................... 1  Power Supplies ............................................................................ 22  Functional Block Diagram .............................................................. 1  Conversion Control ................................................................... 23  Revision History ............................................................................... 2  Interfaces.......................................................................................... 24  Specifications..................................................................................... 3  Digital Interface .......................................................................... 24  Timing Specifications .................................................................. 5  Parallel Interface ......................................................................... 24  Absolute Maximum Ratings............................................................ 7  Serial Interface ............................................................................ 25  ESD Caution .................................................................................. 7  Master Serial Interface ............................................................... 25  Pin Configuration and Function Descriptions ............................. 8  Slave Serial Interface .................................................................. 27  Typical Performance Characteristics ........................................... 12  Hardware Configuration ........................................................... 29  Terminology .................................................................................... 16  Software Configuration ............................................................. 29  Theory of Operation ...................................................................... 17  Microprocessor Interfacing ....................................................... 30  Overview...................................................................................... 17  Application Information ................................................................ 31  Converter Operation .................................................................. 17  Layout Guidelines....................................................................... 31  Modes of Operation ................................................................... 18  Outline Dimensions ....................................................................... 32  Transfer Functions...................................................................... 18  Ordering Guide .......................................................................... 32  Typical Connection Diagram ................................................... 18  Analog Inputs .............................................................................. 20  REVISION HISTORY 12/12—Rev. 0 to Rev. A Added Exposed Pad Note ................................................................ 8 Changes to Power Sequencing Section ........................................ 23 Deleted Evaluating Performance Section .................................... 31 Updated Outline Dimensions ....................................................... 32 Changes to Ordering Guide .......................................................... 32 2/07—Revision 0: Initial Version Rev. A | Page 2 of 32 Data Sheet AD7952 SPECIFICATIONS AVDD = DVDD = 5 V; OVDD = 2.7 V to 5.5 V; VCC = 15 V; VEE = −15 V; VREF = 5 V; all specifications TMIN to TMAX, unless otherwise noted. Table 2. Parameter RESOLUTION ANALOG INPUTS Differential Voltage Range, VIN 0 V to 5 V 0 V to 10 V ±5 V ±10 V Operating Voltage Range 0 V to 5 V 0 V to 10 V ±5 V ±10 V Common-Mode Voltage Range 5V 10 V Bipolar Ranges Analog Input CMRR Input Current Input Impedance THROUGHPUT SPEED Complete Cycle Throughput Rate Time Between Conversions Complete Cycle Throughput Rate Complete Cycle Throughput Rate DC ACCURACY Integral Linearity Error2 No Missing Codes2 Differential Linearity Error2 Transition Noise Zero Error (Unipolar or Bipolar) Zero-Error Temperature Drift Full-Scale Error (Unipolar or Bipolar) Full-Scale Error Temperature Drift Power Supply Sensitivity AC ACCURACY Dynamic Range Signal-to-Noise Ratio, SNR Signal-to-(Noise + Distortion), SINAD Total Harmonic Distortion Spurious-Free Dynamic Range −3 dB Input Bandwidth Aperture Delay Aperture Jitter Transient Response Conditions/Comments (VIN+) − (VIN−) VIN = 10 V p-p VIN = 20 V p-p VIN = 20 V p-p VIN = 40 V p-p VIN+, VIN− to AGND Min 14 Typ Max Unit Bits −VREF −2 VREF −2 VREF −4 VREF +VREF +2 VREF +2 VREF +4 VREF V V V V −0.1 −0.1 −5.1 −10.1 +5.1 +10.1 +5.1 +10.1 V V V V VREF/2 + 0.1 VREF + 0.2 +0.1 V V V dB μA 1 1 1 1.25 800 1.49 670 μs MSPS ms μs kSPS μs kSPS +1 LSB3 Bits LSB LSB LSB ppm/°C LSB ppm/°C LSB VIN+, VIN− VREF/2 − 0.1 VREF − 0.2 −0.1 fIN = 100 kHz VIN = ±5 V, ±10 V @ 670 kSPS See Analog Inputs section In warp mode In warp mode In warp mode In normal mode In normal mode In impulse mode In impulse mode VREF/2 VREF 0 75 2201 1 0 0 −1 14 −1 ±0.3 +1 0.55 −15 +15 ±1 −20 +20 ±1 ±0.8 AVDD = 5 V ± 5% fIN = 2 kHz, −60 dB fIN = 2 kHz fIN = 20 kHz fIN = 2 kHz fIN = 2 kHz fIN = 2 kHz VIN = 0 V to 5 V 84.5 84.5 83 Full-scale step 85.5 85.5 85.5 85.4 −105 102 45 2 5 500 Rev. A | Page 3 of 32 dB4 dB dB dB dB dB MHz ns ps rms ns AD7952 Parameter INTERNAL REFERENCE Output Voltage Temperature Drift Line Regulation Long-Term Drift Turn-On Settling Time REFERENCE BUFFER REFBUFIN Input Voltage Range EXTERNAL REFERENCE Voltage Range Current Drain TEMPERATURE PIN Voltage Output Temperature Sensitivity Output Resistance DIGITAL INPUTS Logic Levels VIL VIH IIL IIH DIGITAL OUTPUTS Data Format Pipeline Delay5 VOL VOH POWER SUPPLIES Specified Performance AVDD DVDD OVDD VCC VEE Operating Current7, 8 AVDD With Internal Reference With Internal Reference Disabled DVDD OVDD VCC VEE Power Dissipation With Internal Reference With Internal Reference Disabled In Power-Down Mode9 TEMPERATURE RANGE10 Specified Performance Data Sheet Conditions/Comments PDREF = PDBUF = low REF @ 25°C –40°C to +85°C AVDD = 5 V ± 5% 1000 hours CREF = 22 μF PDREF = high PDREF = PDBUF = high REF 1 MSPS throughput Min Typ Max Unit 4.965 5.000 ±3 ±15 50 10 5.035 V ppm/°C ppm/V ppm ms 2.4 2.5 2.6 V 4.75 5 200 AVDD + 0.1 V μA @ 25°C 311 1 4.33 −0.3 2.1 −1 −1 mV mV/°C kΩ +0.6 OVDD + 0.3 +1 +1 V V μA μA 0.4 V V 5.25 5.25 5.25 15.75 0 V V V V V Parallel or serial 14-bit ISINK = 500 μA ISOURCE = −500 μA OVDD − 0.6 4.756 4.75 2.7 7 −15.75 5 5 15 −15 @ 1 MSPS throughput 20 18.5 7 0.5 4 3 2 VCC = 15 V, with internal reference buffer VCC = 15 V VEE = −15 V @ 1 MSPS throughput PDREF = PDBUF = low PDREF = PDBUF = high PD = high TMIN to TMAX 235 215 10 −40 1 mA mA mA mA mA mA mA 260 240 mW mW μW +85 °C With VIN = unipolar 5 V or unipolar 10 V ranges, the input current is typically 70 μA. In all input ranges, the input current scales with throughput. See the Analog Inputs section. Linearity is tested using endpoints, not best fit. All linearity is tested with an external 5 V reference. LSB means least significant bit. All specifications in LSB do not include the error contributed by the reference. 4 All specifications in dB are referred to a full-scale range input, FSR. Tested with an input signal at 0.5 dB below full-scale, unless otherwise specified. 5 Conversion results are available immediately after completed conversion. 6 4.75 V or VREF − 0.1 V, whichever is larger. 7 Tested in parallel reading mode. 8 With internal reference, PDREF = PDBUF = low; with internal reference disabled, PDREF = PDBUF = high. With internal reference buffer, PDBUF = low. 9 With all digital inputs forced to OVDD. 10 Consult sales for extended temperature range. 2 3 Rev. A | Page 4 of 32 Data Sheet AD7952 TIMING SPECIFICATIONS AVDD = DVDD = 5 V; OVDD = 2.7 V to 5.5 V; VCC = 15 V; VEE = −15 V; VREF = 5 V; all specifications TMIN to TMAX, unless otherwise noted. Table 3. Parameter CONVERSION AND RESET (See Figure 34 and Figure 35) Convert Pulse Width Time Between Conversions Warp Mode/Normal Mode/Impulse Mode1 CNVST Low to BUSY High Delay BUSY High All Modes (Except Master Serial Read After Convert) Warp Mode/Normal Mode/Impulse Mode Aperture Delay End of Conversion to BUSY Low Delay Conversion Time Warp Mode/Normal Mode/Impulse Mode Acquisition Time Warp Mode/Normal Mode/Impulse Mode RESET Pulse Width PARALLEL INTERFACE MODES (See Figure 36 and Figure 38) CNVST Low to DATA Valid Delay Warp Mode/Normal Mode/Impulse Mode DATA Valid to BUSY Low Delay Bus Access Request to DATA Valid Bus Relinquish Time MASTER SERIAL INTERFACE MODES2 (See Figure 40 and Figure 41) CS Low to SYNC Valid Delay CS Low to Internal SDCLK Valid Delay2 CS Low to SDOUT Delay CNVST Low to SYNC Delay, Read During Convert Warp Mode/Normal Mode/Impulse Mode SYNC Asserted to SDCLK First Edge Delay Internal SDCLK Period3 Internal SDCLK High3 Internal SDCLK Low3 SDOUT Valid Setup Time3 SDOUT Valid Hold Time3 SDCLK Last Edge to SYNC Delay3 CS High to SYNC High-Z CS High to Internal SDCLK High-Z CS High to SDOUT High-Z BUSY High in Master Serial Read After Convert3 CNVST Low to SYNC Delay, Read After Convert Warp Mode/Normal Mode/Impulse Mode SYNC Deasserted to BUSY Low Delay Symbol Min t1 t2 10 Typ Max ns 1/1.25/1.49 t3 t4 t5 t6 t7 Unit 35 μs ns 850/1100/1350 ns ns ns 850/1100/1350 ns 2 10 t8 t9 200 10 ns ns t10 850/1100/1350 t11 t12 t13 40 15 ns ns ns ns 10 10 10 ns ns ns 20 2 t14 t15 t16 t17 50/290/530 t18 t19 t20 t21 t22 t23 t24 t25 t26 t27 t28 t29 t30 Rev. A | Page 5 of 32 3 30 15 10 4 5 5 45 10 10 10 ns ns ns ns ns ns ns ns ns ns ns See Table 4 710/950/1190 25 ns ns AD7952 Data Sheet Parameter SLAVE SERIAL/SERIAL CONFIGURATION INTERFACE MODES2 (See Figure 43, Figure 44, and Figure 46) External SDCLK, SCCLK Setup Time External SDCLK Active Edge to SDOUT Delay SDIN/SCIN Setup Time SDIN/SCIN Hold Time External SDCLK/SCCLK Period External SDCLK/SCCLK High External SDCLK/SCCLK Low Symbol Min t31 t32 t33 t34 t35 t36 t37 5 2 5 5 25 10 10 Typ Max Unit ns ns ns ns ns ns ns 18 1 In warp mode only, the time between conversions is 1 ms; otherwise, there is no required maximum time. In serial interface modes, the SYNC, SDSCLK, and SDOUT timings are defined with a maximum load CL of 10 pF; otherwise, the load is 60 pF maximum. 3 In serial master read during convert mode. See Table 4 for serial master read after convert mode. 2 Table 4. Serial Clock Timings in Master Read After Convert Mode DIVSCLK[1] DIVSCLK[0] SYNC to SDCLK First Edge Delay Minimum Internal SDCLK Period Minimum Internal SDCLK Period Maximum Internal SDCLK High Minimum Internal SDCLK Low Minimum SDOUT Valid Setup Time Minimum SDOUT Valid Hold Time Minimum SDCLK Last Edge to SYNC Delay Minimum BUSY High Width Maximum Warp Mode Normal Mode Impulse Mode 1.6mA 0 0 3 30 45 12 10 4 5 5 0 1 20 60 90 30 25 20 8 7 1 0 20 120 180 60 55 20 35 35 1 1 20 240 360 120 115 20 90 90 Unit ns ns ns ns ns ns ns ns 1.60 1.85 2.10 2.35 2.60 2.85 3.75 4.00 4.25 6.75 7.00 7.25 μs μs μs IOL 1.4V 2V CL 60pF 0.8V tDELAY IOH NOTES 1. IN SERIAL INTERFACE MODES, THE SYNC, SDCLK, AND SDOUT ARE DEFINED WITH A MAXIMUM LOAD CL OF 10pF; OTHERWISE, THE LOAD IS 60pF MAXIMUM. tDELAY 2V 0.8V 2V 0.8V Figure 2. Load Circuit for Digital Interface Timing, SDOUT, SYNC, and SDCLK Outputs, CL = 10 pF Figure 3. Voltage Reference Levels for Timing Rev. A | Page 6 of 32 06589-003 500µA 06589-002 TO OUTPUT PIN Symbol t18 t19 t19 t20 t21 t22 t23 t24 t28 Data Sheet AD7952 ABSOLUTE MAXIMUM RATINGS Table 5. Parameter Analog Inputs/Outputs IN+1, IN−1 to AGND REF, REFBUFIN, TEMP, REFGND to AGND Ground Voltage Differences AGND, DGND, OGND Supply Voltages AVDD, DVDD, OVDD AVDD to DVDD, AVDD to OVDD DVDD to OVDD VCC to AGND, DGND VEE to GND Digital Inputs PDREF, PDBUF Internal Power Dissipation2 Internal Power Dissipation3 Junction Temperature Storage Temperature Range Rating VEE − 0.3 V to VCC + 0.3 V AVDD + 0.3 V to AGND − 0.3 V ±0.3 V −0.3 V to +7 V ±7 V ±7 V –0.3 V to +16.5 V +0.3 V to −16.5 V −0.3 V to OVDD + 0.3 V ±20 mA 700 mW 2.5 W 125°C −65°C to +125°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION 1 See the Analog Inputs section. Specification is for the device in free air: 48-Lead LQFP; θJA = 91°C/W, θJC = 30°C/W. 3 Specification is for the device in free air: 48-Lead LFCSP; θJA = 26°C/W. 2 Rev. A | Page 7 of 32 AD7952 Data Sheet 48 47 46 45 44 43 42 REF IN– REFGND VCC VEE IN+ AGND AVDD TEMP REFBUFIN PDREF PDBUF PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 41 40 39 38 37 36 BIPOLAR 35 CNVST 3 34 PD 4 33 RESET OB/2C 5 32 CS 31 RD 30 TEN 8 29 BUSY NC 9 28 D13/SCCS NC 10 27 D12/SCCLK D0/DIVSCLK[0] 11 26 D11/SCIN D1/DIVSCLK[1] 12 25 D10/HW/SW AGND 1 AVDD 2 AGND BYTESWAP WARP PIN 1 AD7952 6 TOP VIEW (Not to Scale) IMPULSE 7 SER/PAR NOTES 1. NC = NO CONNECT. 2. FOR THE LEAD FRAME CHIP SCALE PACKAGE (LFCSP), THE EXPOSED PAD SHOULD BE CONNECTED TO VEE. THIS CONNECTION IS NOT REQUIRED TO MEET THE ELECTRICAL PERFORMANCES. 06589-004 D9/RDERROR D8/SYNC D7/SDCLK DGND D6/SDOUT DVDD OVDD OGND D5/RDC/SDIN D4/INVSCLK D2/EXT/INT D3/INVSYNC 13 14 15 16 17 18 19 20 21 22 23 24 Figure 4. Pin Configuration Table 6. Pin Function Descriptions Pin No. 1, 3, 42 Mnemonic AGND Type1 P 2, 44 4 AVDD BYTESWAP P DI 5 OB/2C DI2 6 WARP DI2 7 IMPULSE DI2 8 SER/PAR DI 9, 10 NC DO Description Analog Power Ground Pins. Ground reference point for all analog I/O. All analog I/O should be referenced to AGND and should be connected to the analog ground plane of the system. In addition, the AGND, DGND, and OGND voltages should be at the same potential. Analog Power Pins. Nominally 4.75 V to 5.25 V and decoupled with 10 μF and 100 nF capacitors. Parallel Mode Selection (8 Bit/14 Bit). When high, the LSB is output on D[15:8] and the MSB is output on D[7:0]; when low, the LSB is output on D[7:0] and the MSB is output on D[15:8]. Straight Binary/Binary Twos Complement Output. When high, the digital output is straight binary. When low, the MSB is inverted resulting in a twos complement output from its internal shift register. Conversion Mode Selection. Used in conjunction with the IMPULSE input per the following. Conversion Mode WARP IMPULSE Normal Low Low Impulse Low High Warp High Low Normal High High See the Modes of Operation section for a more detailed description. Conversion Mode Selection. See the WARP pin description in this table. See the Modes of Operation section for a more detailed description. Serial/Parallel Selection Input. When SER/PAR = low, the parallel mode is selected. When SER/PAR = high, the serial modes are selected. Some bits of the data bus are used as a serial port, and the remaining data bits are high impedance outputs. No Connect. Do not connect. Rev. A | Page 8 of 32 Data Sheet AD7952 Pin No. 11, 12 Mnemonic D[0:1] or DIVSCLK[0:1] Type1 DI/O 13 D2 or EXT/INT DI/O 14 D3 or INVSYNC DI/O 15 D4 or INVSCLK DI/O 16 D5 or RDC or DI/O Description In parallel mode, these outputs are used as Bit 0 and Bit 1 of the parallel port data output bus. Serial Data Division Clock Selection. In serial master read after convert mode (SER/PAR = high, EXT/INT = low, RDC/SDIN = low), these inputs can be used to slow down the internally generated serial data clock that clocks the data output. In other serial modes, these pins are high impedance outputs. In parallel mode, this output is used as Bit 2 of the parallel port data output bus. Serial Data Clock Source Select. In serial mode, this input is used to select the internally generated (master) or external (slave) serial data clock for the AD7952 output data. When EXT/INT = low (master mode), the internal serial data clock is selected on SDCLK output. When EXT/INT = high (slave mode), the output data is synchronized to an external clock signal (gated by CS) connected to the SDCLK input. SDIN 17 OGND P 18 OVDD P 19 DVDD P 20 DGND P 21 D6 or SDOUT DO 22 D7 or SDCLK DI/O In parallel mode, this output is used as Bit 3 of the parallel port data output bus. Serial Data Invert Sync Select. In serial master mode (SER/PAR = high, EXT/INT = low), this input is used to select the active state of the SYNC signal. When INVSYNC = low, SYNC is active high. When INVSYNC = high, SYNC is active low. In parallel mode, this output is used as Bit 4 of the parallel port data output bus. In all serial modes, invert SDCLK/SCCLK select. This input is used to invert both SDCLK and SCCLK. When INVSCLK = low, the rising edge of SDCLK/SCCLK are used. When INVSCLK = high, the falling edge of SDCLK/SCCLK are used. In parallel mode, this output is used as Bit 5 of the parallel port data output bus. Serial Data Read During Convert. In serial master mode (SER/PAR = high, EXT/INT = low), RDC is used to select the read mode. Refer to the Master Serial Interface section. When RDC = low, the current result is read after conversion. Note the maximum throughput is not attainable in this mode. When RDC = high, the previous conversion result is read during the current conversion. Serial Data In. In serial slave mode (SER/PAR = high, EXT/INT = high), SDIN can be used as a data input to daisy-chain the conversion results from two or more ADCs onto a single SDOUT line. The digital data level on SDIN is output on SDOUT with a delay of 16 SDCLK periods after the initiation of the read sequence. Input/Output Interface Digital Power Ground. Ground reference point for digital outputs. Should be connected to the system digital ground ideally at the same potential as AGND and DGND. Input/Output Interface Digital Power. Nominally at the same supply as the supply of the host interface 2.5 V, 3 V, or 5 V and decoupled with 10 μF and 100 nF capacitors. Digital Power. Nominally at 4.75 V to 5.25 V and decoupled with 10 μF and 100 nF capacitors. Can be supplied from AVDD. Digital Power Ground. Ground reference point for digital outputs. Should be connected to system digital ground ideally at the same potential as AGND and OGND. In parallel mode, this output is used as Bit 6 of the parallel port data output bus. Serial Data Output. In all serial modes, this pin is used as the serial data output synchronized to SDCLK. Conversion results are stored in an on-chip register. The AD7952 provides the conversion result, MSB first, from its internal shift register. The data format is determined by the logic level of OB/2C. When EXT/INT = low (master mode), SDOUT is valid on both edges of SDCLK. When EXT/INT = high (slave mode): When INVSCLK = low, SDOUT is updated on SDCLK rising edge. When INVSCLK = high, SDOUT is updated on SDCLK falling edge. In parallel mode, this output is used as Bit 7 of the parallel port data output bus. Serial Data Clock. In all serial modes, this pin is used as the serial data clock input or output, dependent on the logic state of the EXT/INT pin. The active edge where the data SDOUT is updated depends on the logic state of the INVSCLK pin. Rev. A | Page 9 of 32 AD7952 Data Sheet Pin No. 23 Mnemonic D8 or SYNC Type1 DO 24 D9 or RDERROR DO 25 D10 or HW/SW DI/O 26 D11 or SCIN DI/O 27 D12 or SCCLK DI/O 28 D13 or SCCS DI/O 29 BUSY DO 30 TEN DI2 31 32 RD CS DI DI 33 RESET DI 34 PD DI2 35 CNVST DI 36 BIPOLAR DI2 Description In parallel mode, this output is used as Bit 8 of the parallel port data output bus. Serial Data Frame Synchronization. In serial master mode (SER/PAR = high, EXT/INT= low), this output is used as a digital output frame synchronization for use with the internal data clock. When a read sequence is initiated and INVSYNC = low, SYNC is driven high and remains high while the SDOUT output is valid. When a read sequence is initiated and INVSYNC = high, SYNC is driven low and remains low while the SDOUT output is valid. In parallel mode, this output is used as Bit 9 of the parallel port data output bus. Serial Data Read Error. In serial slave mode (SER/PAR = high, EXT/INT = high), this output is used as an incomplete data read error flag. If a data read is started and not completed when the current conversion is completed, the current data is lost and RDERROR is pulsed high. In parallel mode, this output is used as Bit 10 of the parallel port data output bus. Serial Configuration Hardware/Software Select. In serial mode, this input is used to configure the AD7952 by hardware or software. See the Hardware Configuration section and Software Configuration section. When HW/SW = low, the AD7952 is configured through software using the serial configuration register. When HW/SW = high, the AD7952 is configured through dedicated hardware input pins. In parallel mode, this output is used as Bit 11 of the parallel port data output bus. Serial Configuration Data Input. In serial software configuration mode (SER/PAR = high, HW/SW = low), this input is used to serially write in, MSB first, the configuration data into the serial configuration register. The data on this input is latched with SCCLK. See the Software Configuration section. In parallel mode, this output is used as Bit 12 of the parallel port data output bus. Serial Configuration Clock. In serial software configuration mode (SER/PAR = high, HW/SW = low), this input is used to clock in the data on SCIN. The active edge where the data SCIN is updated depends on the logic state of the INVSCLK pin. See the Software Configuration section. In parallel mode, this output is used as Bit 13 of the parallel port data output bus. Serial Configuration Chip Select. In serial software configuration mode (SER/PAR = high, HW/SW = low), this input enables the serial configuration port. See the Software Configuration section. Busy Output. Transitions high when a conversion is started and remains high until the conversion is completed and the data is latched into the on-chip shift register. The falling edge of BUSY can be used as a data-ready clock signal. Note that in master read after convert mode (SER/PAR = high, EXT/INT = low, RDC = low), the busy time changes according to Table 4. Input Range Select. Used in conjunction with BIPOLAR per the following. Input Range (V) BIPOLAR TEN 0 to 5 Low Low 0 to 10 Low High ±5 High Low ±10 High High Read Data. When CS and RD are both low, the interface parallel or serial output bus is enabled. Chip Select. When CS and RD are both low, the interface parallel or serial output bus is enabled. CS is also used to gate the external clock in slave serial mode (not used for serial configurable port). Reset Input. When high, reset the AD7952. Current conversion, if any, is aborted. The falling edge of RESET resets the data outputs to all zeros (with OB/2C = high) and clears the configuration register. See the Digital Interface section. If not used, this pin can be tied to OGND. Power-Down Input. When PD = high, powers down the ADC. Power consumption is reduced and conversions are inhibited after the current one is completed. The digital interface remains active during power-down. Conversion Start. A falling edge on CNVST puts the internal sample-and-hold into the hold state and initiates a conversion. Input Range Select. See description for Pin 30. Rev. A | Page 10 of 32 Data Sheet AD7952 Pin No. 37 Mnemonic REF Type1 AI/O 38 39 REFGND IN− AI AI 40 41 43 VCC VEE IN+ P P AI 45 TEMP AO 46 REFBUFIN AI 47 PDREF DI 48 PDBUF DI 49 EPAD3 NC Description Reference Input/Output. When PDREF/PDBUF = low, the internal reference and buffer are enabled, producing 5 V on this pin. When PDREF/PDBUF = high, the internal reference and buffer are disabled, allowing an externally supplied voltage reference up to AVDD volts. Decoupling with at least a 22 μF capacitor is required with or without the internal reference and buffer. See the Reference Decoupling section. Reference Input Analog Ground. Connected to analog ground plane. Analog Input. Referenced to IN+. In the 0 V to 5 V input range, IN− is between 0 V and VREF V centered about VREF/2. In the 0 V to 10 V range, IN− is between 0 V and 2 VREF V centered about VREF. In the ±5 V and ±10 V ranges, IN− is true bipolar up to ±2 VREF V (±5 V range) or ±4 VREF V (±10 V range) and centered about 0 V. In all ranges, IN− must be driven 180° out of phase with IN+. High Voltage Positive Supply. Normally 7 V to 15 V. High Voltage Negative Supply. Normally 0 V to −15 V (0 V in unipolar ranges). Analog Input. Referenced to IN−. In the 0 V to 5 V input range, IN+ is between 0 V and VREF V centered about VREF/2. In the 0 V to 10 V range, IN+ is between 0 V and 2 VREF V centered about VREF. In the ±5 V and ±10 V ranges, IN+ is true bipolar up to ±2 VREF V (±5 V range) or ±4 VREF V (±10 V range) and centered about 0 V. In all ranges, IN+ must be driven 180° out of phase with IN−. Temperature Sensor Analog Output. When the internal reference is enabled (PDREF = PDBUF = low), this pin outputs a voltage proportional to the temperature of the AD7952. See the Temperature Sensor section. Reference Buffer Input. When using an external reference with the internal reference buffer (PDBUF = low, PDREF = high), applying 2.5 V on this pin produces 5 V on the REF pin. See the Single-to-Differential Driver section. Internal Reference Power-Down Input. When low, the internal reference is enabled. When high, the internal reference is powered down, and an external reference must be used. Internal Reference Buffer Power-Down Input. When low, the buffer is enabled (must be low when using internal reference). When high, the buffer is powered down. Exposed Pad. The exposed pad is not connected internally. It is recommended that the pad be soldered to VEE. 1 AI = analog input; AI/O = bidirectional analog; AO = analog output; DI = digital input; DI/O = bidirectional digital; DO = digital output; P = power. In serial configuration mode (SER/PAR = high, HW/SW = low), this input is programmed with the serial configuration register, and this pin is a don’t care. See the Hardware Configuration section and Software Configuration section. 3 LFCSP_VQ package only. 2 Rev. A | Page 11 of 32 AD7952 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS AVDD = DVDD = 5 V; OVDD = 5 V; VCC = 15 V; VEE = −15 V; VREF = 5 V; TA = 25°C. 1.0 1.0 POSITIVE INL = +0.15 NEGATIVE INL = –0.15 0.5 DNL (LSB) 0 0 –0.5 0 4096 8192 12288 16384 CODE –1.0 06589-005 –1.0 –0.5 0 12288 16384 Figure 8. Differential Nonlinearity vs. Code 200 NEGATIVE INL POSITIVE INL NEGATIVE DNL POSITIVE DNL 180 200 160 NUMBER OF UNITS NUMBER OF UNITS 8192 CODE Figure 5. Integral Nonlinearity vs. Code 250 4096 06589-008 INL (LSB) 0.5 POSITIVE DNL = +0.27 NEGATIVE DNL = –0.27 150 100 50 140 120 100 80 60 40 –0.8 –0.6 –0.4 –0.2 0 0.2 0.4 0.6 0.8 INL DISTRIBUTION (LSB) 1.0 0 –1.0 06589-006 0 –1.0 –0.8 –0.6 –0.4 –0.2 Figure 6. Integral Nonlinearity Distribution (239 Devices) 0.2 0.4 0.6 0.8 1.0 Figure 9. Differential Nonlinearity Distribution (239 Devices) 300000 140000 132052 261120 129068 120000 250000 100000 COUNTS 200000 150000 80000 60000 100000 40000 50000 0 1FFF 0 2000 2001 0 2002 0 2003 CODE IN HEX Figure 7. Histogram of 261,120 Conversions of a DC Input at the Code Center 0 0 0 8192 8193 8194 8195 0 0 8196 8197 CODE IN HEX Figure 10. Histogram of 261,120 Conversions of a DC Input at the Code Transition Rev. A | Page 12 of 32 06589-010 0 20000 06589-007 COUNTS 0 DNL DISTRIBUTION (LSB) 06589-009 20 Data Sheet AD7952 SNR, SINAD REFERRED TO FULL SCALE (dB) –40 –60 –80 –100 –120 –140 0 100 200 300 400 500 FREQUENCY (kHz) 85.5 85.0 –60 14.5 –80 THD, HARMONICS (dB) 13.9 82 ENOB (Bits) 14.1 –10 0 13.7 80 100 –100 06589-012 FREQUENCY (kHz) THIRD HARMONIC –110 80 SECOND HARMONIC –130 70 1 60 100 10 FREQUENCY (kHz) Figure 12. SNR, SINAD, and ENOB vs. Frequency 86.0 90 THD –120 13.5 100 10 110 SFDR –90 Figure 15. THD, Harmonics, and SFDR vs. Frequency 86.0 0V TO 5V 0V TO 10V ±5V ±10V 85.5 0V TO 5V 0V TO 10V ±5V ±10V SINAD (dB) 85.5 85.0 84.5 85.0 –35 –15 5 25 45 65 TEMPERATURE (°C) 85 105 125 Figure 13. SNR vs. Temperature 84.0 –55 –35 –15 5 25 45 65 85 TEMPERATURE (°C) Figure 16. SINAD vs. Temperature Rev. A | Page 13 of 32 105 125 06589-016 84.5 06589-013 SNR, SINAD (dB) SINAD ENOB SNR (dB) –20 120 SNR 84.0 –55 –30 –70 14.3 86 1 –40 Figure 14. SNR and SINAD vs. Input Level (Referred to Full Scale) 88 78 –50 INPUT LEVEL (dB) Figure 11. FFT 20 kHz 84 SNR SINAD 06589-011 –160 86.0 06589-014 SNR = 85.4dB THD = –107dB SFDR = 116dB SINAD = 85.4dB SFDR (dB) –20 AMPLITUDE (dB OF FULL SCALE) 86.5 fS = 1000kSPS fIN = 19.94kHz 06589-015 0 AD7952 –96 Data Sheet 124 0V TO 5V 0V TO 10V ±5V ±10V –100 0V TO 5V 0V TO 10V ±5V ±10V 122 120 118 SFDR (dB) THD (dB) –104 –108 116 114 112 –112 110 –116 –35 –15 5 25 45 65 85 105 125 TEMPERATURE (°C) 106 –55 06589-017 –120 –55 –15 5 25 45 65 85 105 125 TEMPERATURE (°C) Figure 17. THD vs. Temperature Figure 20. SFDR vs. Temperature (Excludes Harmonics) 1.5 5.008 NEGATIVE FULL-SCALE ERROR 1.0 0.5 5.006 5.004 VREF (V) POSITIVE FULL-SCALE ERROR 0 –0.5 5.002 5.000 ZERO ERROR –1.5 –55 –35 –15 5 25 45 65 85 105 125 TEMPERATURE (°C) 4.996 –55 Figure 18. Zero Error, Positive and Negative Full-Scale Error vs. Temperature 60 –35 –15 5 25 45 65 85 105 125 TEMPERATURE (°C) 06589-021 4.998 –1.0 06589-018 ZERO ERROR, FULL-SCALE ERROR (LSB) –35 06589-020 108 Figure 21. Typical Reference Voltage Output vs. Temperature (3 Devices) 100000 AVDD, WARP/NORMAL 10000 DVDD, ALL MODES OPERATING CURRENTS (µA) 40 30 20 10 100 10 AVDD, IMPULSE VCC +15V VEE –15V ALL MODES 1 0.1 OVDD, ALL MODES 0.01 0 1 2 3 4 5 6 REFERENCE DRIFT (ppm/°C) 7 8 06589-019 0 1000 Figure 19. Reference Voltage Temperature Coefficient Distribution (247 Devices) Rev. A | Page 14 of 32 0.001 10 PDREF = PDBUF = HIGH 100 1000 10000 100000 SAMPLING RATE (SPS) Figure 22. Operating Currents vs. Sample Rate 1000000 06589-022 NUMBER OF UNITS 50 Data Sheet AD7952 50 PD = PDBUF = PDREF = HIGH VEE = –15V VCC = +15V 600 DVDD OVDD AVDD 500 OVDD = 2.7V @ 85°C 45 OVDD = 2.7V @ 25°C 40 t12 DELAY (ns) 35 400 300 30 25 OVDD = 5V @ 85°C 20 OVDD = 5V @ 25°C 15 200 10 100 0 –35 –15 5 25 45 65 85 105 TEMPERATURE (°C) Figure 23. Power-Down Operating Currents vs. Temperature 0 50 100 150 CL (pF) Figure 24. Typical Delay vs. Load Capacitance CL Rev. A | Page 15 of 32 200 06589-024 0 –55 5 06589-023 POWER–DOWN OPERATING CURRENTS (nA) 700 AD7952 Data Sheet TERMINOLOGY Least Significant Bit (LSB) Total Harmonic Distortion (THD) The least significant bit, or LSB, is the smallest increment that can be represented by a converter. For a fully differential input ADC with N bits of resolution, the LSB expressed in volts is THD is the ratio of the rms sum of the first five harmonic components to the rms value of a full-scale input signal and is expressed in decibels. LSB (V )  VINp-p Signal-to-(Noise + Distortion) Ratio (SINAD) 2N Integral Nonlinearity Error (INL) Linearity error refers to the deviation of each individual code from a line drawn from negative full scale through positive full scale. The point used as negative full scale occurs a ½ LSB before the first code transition. Positive full scale is defined as a level 1½ LSBs beyond the last code transition. The deviation is measured from the middle of each code to the true straight line. Differential Nonlinearity Error (DNL) In an ideal ADC, code transitions are 1 LSB apart. Differential nonlinearity is the maximum deviation from this ideal value. It is often specified in terms of resolution for which no missing codes are guaranteed. Bipolar Zero Error The difference between the ideal midscale input voltage (0 V) and the actual voltage producing the midscale output code. SINAD is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the Nyquist frequency, including harmonics but excluding dc. The value for SINAD is expressed in decibels. Spurious-Free Dynamic Range (SFDR) The difference, in decibels (dB), between the rms amplitude of the input signal and the peak spurious signal. Effective Number of Bits (ENOB) ENOB is a measurement of the resolution with a sine wave input. It is related to SINAD and is expressed in bits by ENOB = [(SINADdB − 1.76)/6.02] Aperture Delay Aperture delay is a measure of the acquisition performance measured from the falling edge of the CNVST input to when the input signal is held for a conversion. Transient Response Unipolar Offset Error The first transition should occur at a level ½ LSB above analog ground. The unipolar offset error is the deviation of the actual transition from that point. Full-Scale Error The time required for the AD7952 to achieve its rated accuracy after a full-scale step function is applied to its input. Reference Voltage Temperature Coefficient Reference voltage temperature coefficient is derived from the typical shift of the output voltage at 25°C on a sample of parts at the maximum and minimum reference output voltage (VREF) measured at TMIN, T (25°C), and TMAX. It is expressed in ppm/°C as The last transition (from 111…10 to 111…11) should occur for an analog voltage 1½ LSB below the nominal full scale. The fullscale error is the deviation in LSB (or % of full-scale range) of the actual level of the last transition from the ideal level and includes the effect of the offset error. Closely related is the gain error (also in LSB or % of full-scale range), which does not include the effects of the offset error. where: Dynamic Range VREF (Max) = maximum VREF at TMIN, T (25°C), or TMAX. Dynamic range is the ratio of the rms value of the full scale to the rms noise measured for an input typically at −60 dB. The value for dynamic range is expressed in decibels. VREF (Min) = minimum VREF at TMIN, T (25°C), or TMAX. VREF (25°C) = VREF at 25°C. Signal-to-Noise Ratio (SNR) TMIN = –40°C. TCVREF (ppm/C)  TMAX = +85°C. SNR is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the Nyquist frequency, excluding harmonics and dc. The value for SNR is expressed in decibels. Rev. A | Page 16 of 32 VREF ( Max ) – VREF ( Min) VREF (25C)  (TMAX – TMIN )  106 Data Sheet AD7952 THEORY OF OPERATION IN+ AGND LSB MSB 8192C 4096C 4C 2C C SW+ SWITCHES CONTROL C BUSY REF COMP REFGND 4096C 4C 2C MSB C OUTPUT CODE C SW– LSB CNVST AGND IN– 06589-025 8192C CONTROL LOGIC Figure 25. ADC Simplified Schematic OVERVIEW CONVERTER OPERATION The AD7952 is a very fast, low power, precise, 14-bit ADC using successive approximation, capacitive digital-to-analog (CDAC) converter architecture. The AD7952 is a successive approximation ADC based on a charge redistribution DAC. Figure 25 shows the simplified schematic of the ADC. The CDAC consists of two identical arrays of 16 binary weighted capacitors, which are connected to the two comparator inputs. The AD7952 can be configured at any time for one of four input ranges and conversion mode with inputs in parallel and serial hardware modes or by a dedicated write-only, SPI-compatible interface via a configuration register in serial software mode. The AD7952 uses Analog Devices’ patented iCMOS high voltage process to accommodate 0 V to +5 V, 0 V to +10 V, ±5 V, and ±10 V input ranges without the use of conventional thin films. Only one acquisition cycle, t8, is required for the inputs to latch to the correct configuration. Resetting or power cycling is not required for reconfiguring the ADC. The AD7952 features different modes to optimize performance according to the applications. It is capable of converting 1,000,000 samples per second (1 MSPS) in warp mode, 800 kSPS in normal mode, and 670 kSPS in impulse mode. The AD7952 provides the user with an on-chip, track-and-hold, successive approximation ADC that does not exhibit any pipeline or latency, making it ideal for multiple, multiplexed channel applications. For unipolar input ranges, the AD7952 typically requires three supplies: VCC, AVDD (which can supply DVDD), and OVDD (which can be interfaced to either 5 V, 3.3 V, or 2.5 V digital logic). For bipolar input ranges, the AD7952 requires the use of the additional VEE supply. During the acquisition phase, terminals of the array tied to the comparator’s input are connected to AGND via SW+ and SW−. All independent switches are connected to the analog inputs. Therefore, the capacitor arrays are used as sampling capacitors and acquire the analog signal on IN+ and IN− inputs. A conversion phase is initiated once the acquisition phase is completed and the CNVST input goes low. When the conversion phase begins, SW+ and SW− are opened first. The two capacitor arrays are then disconnected from the inputs and connected to the REFGND input. Therefore, the differential voltage between the inputs (IN+ and IN−) captured at the end of the acquisition phase is applied to the comparator inputs, causing the comparator to become unbalanced. By switching each element of the capacitor array between REFGND and REF, the comparator input varies by binary weighted voltage steps (VREF/2, VREF/4 through VREF/16,384). The control logic toggles these switches, starting with the MSB first, to bring the comparator back into a balanced condition. After the completion of this process, the control logic generates the ADC output code and brings the BUSY output low. The device is housed in Pb-free, 48-lead LQFP or tiny, 48-lead LFCSP (7 mm × 7 mm) that combines space savings with flexibility. In addition, the AD7952 can be configured as either a parallel or a serial SPI-compatible interface. Rev. A | Page 17 of 32 AD7952 Data Sheet MODES OF OPERATION TRANSFER FUNCTIONS The AD7952 features three modes of operation: warp, normal, and impulse. Each of these modes is more suitable to specific applications. The mode is configured with the input pins, WARP and IMPULSE, or via the configuration register. See Table 6 for the pin details and the Hardware Configuration section and Software Configuration section for programming the mode selection with either pins or configuration register. Note that when using the configuration register, the WARP and IMPULSE inputs are don’t cares and should be tied to either high or low. Using the OB/2C digital input or via the configuration register, the AD7952 offers two output codings: straight binary and twos complement. See Figure 26 and Table 7 for the ideal transfer characteristic and digital output codes for the different analog input ranges, VIN. Note that when using the configuration register, the OB/2C input is a don’t care and should be tied to either high or low. Setting WARP = high and IMPULSE = low allows the fastest conversion rate up to 1 MSPS. However, in this mode, the full specified accuracy is guaranteed only when the time between conversions does not exceed 1 ms. If the time between two consecutive conversions is longer than 1 ms (after power-up), the first conversion result should be ignored because in warp mode, the ADC performs a background calibration during the SAR conversion process. This calibration can drift if the time between conversions exceeds 1 ms, thus causing the first conversion to appear offset. This mode makes the AD7952 ideal for applications where both high accuracy and fast sample rate are required. 111...111 111...110 111...101 000...010 000...001 000...000 –FSR –FSR + 1 LSB +FSR – 1 LSB –FSR + 0.5 LSB +FSR – 1.5 LSB ANALOG INPUT 06589-026 ADC CODE (Straight Binary) Warp Mode Figure 26. ADC Ideal Transfer Function Normal Mode TYPICAL CONNECTION DIAGRAM Setting WARP = IMPULSE = low or WARP = IMPULSE = high allows the fastest mode (800 kSPS) without any limitation on time between conversions. This mode makes the AD7952 ideal for asynchronous applications, such as data acquisition systems, where both high accuracy and fast sample rate are required. Figure 27 shows a typical connection diagram for the AD7952 using the internal reference, serial data, and serial configuration interfaces. Different circuitry from that shown in Figure 27 is optional and is discussed in the following sections. Impulse Mode Setting WARP = low and IMPULSE = high uses the lowest power dissipation mode and allows power saving between conversions. The maximum throughput in this mode is 670 kSPS, and in this mode, the ADC powers down circuits after conversion, making the AD7952 ideal for battery-powered applications. Table 7. Output Codes and Ideal Input Voltages Description FSR − 1 LSB FSR − 2 LSB Midscale + 1 LSB Midscale Midscale − 1 LSB −FSR + 1 LSB −FSR 1 2 VIN = 0 V to 5 V (10 V p-p) 4.999695 V 4.999390 V 2.500610 V 2.5 V 2.499390 V 610.4 μV 0V VREF = 5 V VIN = 0 V to 10 V VIN = ±5 V (20 V p-p) (20 V p-p) 9.999389 V +4.999389 V 9.998779 V +4.998779 V 5.000610 V +1.228 mV 5.000000 V 0V 4.999389 V −1.228 mV 1.228 mV −4.999389 V 0V −5 V This is also the code for overrange analog input (VIN+ − VIN− above VREF − VREFGND). This is also the code for overrange analog input (VIN+ − VIN− below VREF − VREFGND). Rev. A | Page 18 of 32 Digital Output Code VIN = ±10 V (40 V p-p) +9.998779 V +9.997558 V +2.442 mV 0V −2.442 mV −9.998779 V −10 V Straight Binary 0x3FFF1 0x3FFE 0x2001 0x2000 0x1FFF 0x0001 0x00002 Twos Complement 0x1FFF1 0x1FFE 0x0001 0x0000 0x3FFF 0x2001 0x20002 Data Sheet AD7952 DIGITAL SUPPLY (5V) NOTE 5 DIGITAL INTERFACE SUPPLY (2.5V, 3.3V, OR 5V) 10Ω ANALOG SUPPLY (5V) 10µF 100nF 10µF AVDD +7V TO +15.75V SUPPLY 10µF 100nF 10µF 100nF AGND 100nF 10µF 100nF DGND DVDD OVDD VCC OGND MicroConverter ®/ MICROPROCESSOR/ DSP BUSY SDCLK –7V TO –15.75V SUPPLY SERIAL PORT 1 SDOUT SCCLK VEE SERIAL PORT 2 SCIN NOTE 6 REF NOTE 4 CREF 22µF 100nF NOTE 3 SCCS REFBUFIN REFGND 33Ω NOTE 7 CNVST AD7952 D OB/2C NOTE 2 ANALOG INPUT+ U1 15Ω SER/PAR IN+ OVDD HW/SW BIPOLAR CC 2.7nF TEN CLOCK WARP IN– NOTE 2 ANALOG INPUT– U1 CC NOTE 1 15Ω IMPULSE NOTE 3 PDREF PDBUF PD RD CS RESET 2.7nF AGND DGND NOTES 1. ANALOG INPUTS ARE DIFFERENTIAL (ANTIPHASE). SEE ANALOG INPUTS SECTION. 2. THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION. 3. THE CONFIGURATION SHOWN IS USING THE INTERNAL REFERENCE. SEE VOLTAGE REFERENCE INPUT/OUTPUT SECTION. 4. A 22µF CERAMIC CAPACITOR (X5R, 1206 SIZE) IS RECOMMENDED (FOR EXAMPLE, PANASONIC ECJ4YB1A226M). SEE VOLTAGE REFERENCE INPUT/OUTPUT SECTION. 5. OPTIONAL, SEE POWER SUPPLIES SECTION. 6. THE VCC AND VEE SUPPLIES SHOULD BE VCC = [VIN(MAX) + 2V] AND VEE = [VIN(MIN) – 2V] FOR BIPOLAR INPUT RANGES. FOR UNIPOLAR INPUT RANGES, VEE CAN BE 0V. SEE POWER SUPPLIES SECTION. 7. OPTIONAL LOW JITTER CNVST, SEE CONVERSION CONTROL SECTION. 8. A SEPARATE ANALOG AND DIGITAL GROUND PLANE IS RECOMMENDED, CONNECTED TOGETHER DIRECTLY UNDER THE ADC. SEE LAYOUT GUIDELINES SECTION. Figure 27. Typical Connection Diagram Shown with Serial Interface and Serial Programmable Port Rev. A | Page 19 of 32 06589-027 NOTE 8 AD7952 Data Sheet Input Range Selection In parallel mode and serial hardware mode, the input range is selected by using the BIPOLAR (bipolar) and TEN (10 V range) inputs. See Table 6 for pin details and the Hardware Configuration section and Software Configuration section for programming the mode selection with either pins or the configuration register. Note that when using the configuration register, the BIPOLAR and TEN inputs are don’t cares and should be tied high or low. For instance, by using IN− to sense a remote signal ground, ground potential differences between the sensor and the local ADC ground are eliminated. 100 90 80 70 CMRR (dB) ANALOG INPUTS Input Structure 60 50 40 30 Figure 28 shows an equivalent circuit for the input structure of the AD7952. 20 1 10 100 1000 FREQUENCY (kHz) D3 D2 D4 RIN VEE AGND CIN 10000 Figure 29. Analog Input CMRR vs. Frequency 06589-028 D1 IN+ OR IN– CPIN 0 AVDD VCC 06589-029 10 0V TO 5V RANGE ONLY Figure 28. Simplified Analog Input The four diodes, D1 to D4, provide ESD protection for the analog inputs, IN+ and IN−. Care must be taken to ensure that the analog input signal never exceeds the supply rails by more than 0.3 V because this causes the diodes to become forward-biased and to start conducting current. These diodes can handle a forwardbiased current of 120 mA maximum. For instance, these conditions could eventually occur when the input buffer’s U1 supplies are different from AVDD, VCC, and VEE. In such a case, an input buffer with a short-circuit current limitation can be used to protect the part although most op amps’ short-circuit current is