AD8003ACP-EBZ

Evaluation Board User Guide UG-022 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluating the AD8003 Triple, 1.5 GHz Op Amp FEATURES The evaluation board is a 4-layer printed circuit board (PCB) that accepts edge-mounted Subminiature A (SMA) connectors on the inputs and outputs, which allows efficient connection to test equipment and other circuits. The ground plane, component placement, and supply bypassing have been optimized for performance and circuit flexibility. The evaluation board uses a variety of surface-mount technology (SMT) component case sizes: 0402, 0603, and 3528. Enables quick breadboarding/prototyping User-defined circuit configuration Edge-mounted SMA connector provisions Easy connection to test equipment and other circuits GENERAL DESCRIPTION The AD8003 evaluation board is specifically designed to evaluate the AD8003, a triple high speed, current feedback amplifier. The evaluation board is a bare board (that is, there are no components soldered to the board) that enables users to quickly prototype a variety of amplifier circuits, which minimizes risk and reduces time to market. Figure 4 and Figure 6 show the component side and circuit side of the evaluation board assembly drawing. The recommended layout pattern for connecting the board to the op amp and to the supporting circuitry is shown in Figure 5 and Figure 7. Figure 1 and Figure 2 show component side and circuit side of the bare evaluation board. Figure 3 shows the evaluation board schematic. NOTES 1. THE EVALUATION BOARD SILKSCREEN PART NUMBER LABELING ON YOUR BOARD MAY BE DIFFERENT FROM WHAT IS SHOWN HERE. 08149-006 NOTES 1. THE EVALUATION BOARD SILKSCREEN PART NUMBER LABELING ON YOUR BOARD MAY BE DIFFERENT FROM WHAT IS SHOWN HERE. Figure 2. Circuit Side of the AD8003 Evaluation Board Figure 1. Component Side of the AD8003 Evaluation Board PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. B | Page 1 of 8 08149-008 DIGITAL PICTURES OF THE COMPONENT SIDE AND CIRCUIT SIDE OF THE EVALUATION BOARD UG-022 Evaluation Board User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Evaluation Board Schematic ............................................................3 General Description ......................................................................... 1 Assembly Drawing and Board Layout ............................................4 Digital Pictures of the Component Side and Circuit Side of the Evaluation Board .............................................................................. 1 Ordering Information .......................................................................5 Bill of Materials ..............................................................................5 Revision History ............................................................................... 2 REVISION HISTORY 9/12—Rev. A to Rev. B Changes to User Guide Title, General Description Section, and Figure 1 .............................................................................................. 1 Changes to Figure 2 Caption ........................................................... 3 Changes to Figure 4 to Figure 7 ...................................................... 4 Added Ordering Information Section, Bill of Materials, and Table 1 ................................................................................................ 5 2/10—Rev. 0 to Rev. A Changes to General Description and Figure 1 ............................. 1 7/09—Revision 0: Initial Version Rev. B | Page 2 of 8 Rev. B | Page 3 of 8 Figure 3. Evaluation Board Schematic VE1 PD1/DIS1 R4* R11* *USER-DEFINED VALUE IN1+ IN1– VC1 AGND AGND AGND JP3 C2 10UF C12 10UF C3 0.1UF AGND AGND AGND 10UF R2* C1 0.1UF AGND C4 AGND AGND C11 0.1UF OUT2 OUT1 R1* VC1 AGND R6* 8 R5* NC 7 6 VE1 5 PD1/DIS1 4 IN1+ 3 IN1– 2 FB1 1 24 VE2 22 9 R15* AGND R7* 10 VE3 OUT3 R9* 12 AGND R10* 11 IN3+ IN3– FB3 VC3 VC2 19 JP1 PD3/DIS3 20 R16* 21 AD8003 R8* 23 PD2/DIS2 OUT1 VE2 IN2+ NC PD2/DIS2 IN2– OUT2 AGND FB2 NC R18* 13 14 15 16 17 18 AGND AGND R19 49.9Ω C5 0.1UF OUT3 R13* AGND R14* AGND 0.1UF C7 AGND C9 0.1UF IN2– C8 10UF AGND C6 10UF JP2 AGND AGND C10 10UF VE3 PD3/DIS3 AGND AGND R12* AGND R17* VC3 VC2 IN3+ IN3– 08149-001 IN2+ Evaluation Board User Guide UG-022 EVALUATION BOARD SCHEMATIC UG-022 Evaluation Board User Guide 08149-002 08149-003 ASSEMBLY DRAWING AND BOARD LAYOUT Figure 6. Board Assembly Drawing, Circuit Side Figure 5. Board Layout Pattern, Component Side 08149-005 08149-004 Figure 4. Board Assembly Drawing, Component Side Figure 7. Board Layout Pattern, Circuit Side Rev. B | Page 4 of 8 Evaluation Board User Guide UG-022 ORDERING INFORMATION BILL OF MATERIALS Table 1. Quantity Reference Designator Description Package 1 13 6 6 1 9 6 3 6 3 PCB VC1 to VC3, VE1 to VE3, PD1/DIS1 to PD3/DIS3, AGND1 to AGND4 C1, C3, C5, C7, C9, C11 C2, C4, C6, C8, C10, C12 DUT IN1+ to IN3+, −IN1 to −IN3, OUT1 to OUT3 R1, R2, R13 to R16 R6, R8, R10 R4, R11, R12, R17 to R19 R5, R7, R9 Printed circuit board CONN-PCB pin vector 0.1 µF capacitors 10 µF capacitors AD8003 SMA connector User defined value User defined value User defined value User defined value CNLOOPTP_D45 0402 3528 QFN24_4X4_PAD2_1X2_1 CNJOHNSON142-0701-801 0402 0603 0603 0603 Rev. B | Page 5 of 8 UG-022 Evaluation Board User Guide NOTES Rev. B | Page 6 of 8 Evaluation Board User Guide UG-022 NOTES Rev. B | Page 7 of 8 UG-022 Evaluation Board User Guide NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2009–2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG08149-0-9/12(B) Rev. B | Page 8 of 8