Low Cost, 80 MHz
FastFET Op Amps
AD8033/AD8034
CONNECTION DIAGRAMS
AD8033
8
NC
7
+VS
+IN 3
6
VOUT
–VS 4
5
NC
NC = NO CONNECT
AD8033
VOUT 1
5
+VS
4
–IN
–VS 2
+IN 3
Figure 1. 8-Lead SOIC (R)
02924-002
NC 1
–IN 2
02924-001
FET input amplifier
1 pA typical input bias current
Very low cost
High speed
80 MHz, −3 dB bandwidth (G = +1)
80 V/μs slew rate (G = +2)
Low noise
11 nV/√Hz (f = 100 kHz)
0.7 fA/√Hz (f = 100 kHz)
Wide supply voltage range: 5 V to 24 V
Low offset voltage: 1 mV typical
Single-supply and rail-to-rail output
High common-mode rejection ratio: −100 dB
Low power: 3.3 mA/amplifier typical supply current
No phase reversal
Small packaging: 8-lead SOIC, 8-lead SOT-23, and 5-lead SC70
Figure 2. 5-Lead SC70 (KS)
VOUT1 1
8
+VS
–IN1 2
7
VOUT2
+IN1 3
6
–IN2
–VS 4
5
+IN2
AD8034
02924-003
FEATURES
Figure 3. 8-Lead SOIC (R) and 8-Lead SOT-23 (RJ)
24
21
VOUT = 200mV p-p
G = +10
18
15
APPLICATIONS
12
GAIN (dB)
Instrumentation
Filters
Level shifting
Buffering
G = +5
9
6
G = +2
3
G = +1
0
–3
The AD8033/AD8034 FastFET™ amplifiers are voltage feedback
amplifiers with FET inputs, offering ease of use and excellent
performance. The AD8033 is a single amplifier and the AD8034
is a dual amplifier. The AD8033/AD8034 FastFET op amps in
Analog Devices, Inc., proprietary XFCB process offer significant
performance improvements over other low cost FET amps, such
as low noise (11 nV/√Hz and 0.7 fA/√Hz) and high speed (80 MHz
bandwidth and 80 V/μs slew rate).
With a wide supply voltage range from 5 V to 24 V and fully
operational on a single supply, the AD8033/AD8034 amplifiers
work in more applications than similarly priced FET input
amplifiers. In addition, the AD8033/AD8034 have rail-to-rail
outputs for added versatility.
G = –1
–6
–9
0.1
1
10
FREQUENCY (MHz)
100
1000
02924-004
GENERAL DESCRIPTION
Figure 4. Small Signal Frequency Response
The AD8033/AD8034 amplifiers only draw 3.3 mA/amplifier of
quiescent current while having the capability of delivering up to
40 mA of load current.
The AD8033 is available in a small package 8-lead SOIC and a
small package 5-lead SC70. The AD8034 is also available in a
small package 8-lead SOIC and a small package 8-lead SOT-23.
They are rated to work over the industrial temperature range of
−40°C to +85°C without a premium over commercial grade
products.
Despite their low cost, the amplifiers provide excellent overall
performance. They offer a high common-mode rejection of
−100 dB, low input offset voltage of 2 mV maximum, and low
noise of 11 nV/√Hz.
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2002–2008 Analog Devices, Inc. All rights reserved.
AD8033/AD8034
TABLE OF CONTENTS
Features .............................................................................................. 1
Input Overdrive .......................................................................... 16
Applications ....................................................................................... 1
Input Impedance ........................................................................ 16
General Description ......................................................................... 1
Thermal Considerations............................................................ 16
Connection Diagrams ...................................................................... 1
Layout, Grounding, and Bypassing Considerations .................. 18
Revision History ............................................................................... 2
Bypassing ..................................................................................... 18
Specifications..................................................................................... 3
Grounding ................................................................................... 18
Absolute Maximum Ratings............................................................ 6
Leakage Currents ........................................................................ 18
Maximum Power Dissipation ..................................................... 6
Input Capacitance ...................................................................... 18
Output Short Circuit .................................................................... 6
Applications Information .............................................................. 19
ESD Caution .................................................................................. 6
High Speed Peak Detector ........................................................ 19
Typical Performance Characteristics ............................................. 7
Active Filters ............................................................................... 20
Test Circuits ..................................................................................... 14
Wideband Photodiode Preamp ................................................ 21
Theory of Operation ...................................................................... 16
Outline Dimensions ....................................................................... 23
Output Stage Drive and Capacitive Load Drive ..................... 16
Ordering Guide .......................................................................... 24
REVISION HISTORY
9/08—Rev. C to Rev. D
Deleted Usable Input Range Parameter, Table 1 ........................... 3
Deleted Usable Input Range Parameter, Table 2 ........................... 4
Deleted Usable Input Range Parameter, Table 3 ........................... 5
4/08—Rev. B to Rev. C
Changes to Format ............................................................. Universal
Changes to Features and General Description ............................. 1
Changes to Figure 13 Caption and Figure 14 Caption ................ 8
Changes to Figure 22 and Figure 23 ............................................... 9
Changes to Figure 25 and Figure 28 ............................................. 10
Changes to Input Capacitance Section ........................................ 18
Changes to Active Filters Section ................................................. 21
Changes to Outline Dimensions................................................... 23
Changes to Ordering Guide .......................................................... 24
8/02—Rev. 0 to Rev. A
Added AD8033 ................................................................... Universal
VOUT = 2 V p-p Deleted from Default Conditions ......... Universal
Added SOIC-8 (R) and SC70 (KS) ..................................................1
Edits to General Description Section .............................................1
Changes to Specifications .................................................................2
New Figure 2 ......................................................................................5
Edits to Maximum Power Dissipation Section ..............................5
Changes to Ordering Guide .............................................................5
Change to TPC 3 ...............................................................................6
Change to TPC 6 ...............................................................................6
Change to TPC 9 ...............................................................................7
New TPC 16 .......................................................................................8
New TPC 17 .......................................................................................8
New TPC 31 .................................................................................... 11
New TPC 35 .................................................................................... 11
New Test Circuit 9 .......................................................................... 13
SC70 (KS) Package Added ............................................................ 19
2/03—Rev. A to Rev. B
Changes to Features.......................................................................... 1
Changes to Connection Diagrams ................................................. 1
Changes to Specifications ................................................................ 2
Changes to Absolute Maximum Ratings ....................................... 4
Replaced TPC 31............................................................................. 11
Changes to TPC 35 ......................................................................... 11
Changes to Test Circuit 3 ............................................................... 12
Updated Outline Dimensions ....................................................... 19
Rev. D | Page 2 of 24
AD8033/AD8034
SPECIFICATIONS
TA = 25°C, VS = ±5 V, RL = 1 kΩ, gain = +2, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Input Overdrive Recovery Time
Output Overdrive Recovery Time
Slew Rate (25% to 75%)
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
Distortion
Second Harmonic
Third Harmonic
Crosstalk, Output-to-Output
Input Voltage Noise
Input Current Noise
DC PERFORMANCE
Input Offset Voltage
Conditions
Min
Typ
G = +1, VOUT = 0.2 V p-p
G = +2, VOUT = 0.2 V p-p
G = +2, VOUT = 2 V p-p
−6 V to +6 V input
−3 V to +3 V input, G = +2
G = +2, VOUT = 4 V step
G = +2, VOUT = 2 V step
G = +2, VOUT = 8 V step
65
80
30
21
135
135
80
95
225
MHz
MHz
MHz
ns
ns
V/μs
ns
ns
−82
−85
−70
−81
−86
11
0.7
dBc
dBc
dBc
dBc
dB
nV/√Hz
fA/√Hz
55
fC = 1 MHz, VOUT = 2 V p-p
RL = 500 Ω
RL = 1 kΩ
RL = 500 Ω
RL = 1 kΩ
f = 1 MHz, G = +2
f = 100 kHz
f = 100 kHz
VCM = 0 V
TMIN − TMAX
1
Input Offset Voltage Match
Input Offset Voltage Drift
Input Bias Current
Open-Loop Gain
INPUT CHARACTERISTICS
Common-Mode Input Impedance
Differential Input Impedance
Input Common-Mode Voltage Range
FET Input Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
Power Supply Rejection Ratio
TMIN − TMAX
VOUT = ± 3 V
89
VCM = −3 V to +1.5 V
−89
±4.75
30% overshoot, G = +1, VOUT = 400 mV p-p
4
1.5
50
92
−90
Rev. D | Page 3 of 24
2
3.5
2.5
27
11
Unit
mV
mV
mV
μV/°C
pA
pA
dB
1000||2.3
1000||1.7
GΩ||pF
GΩ||pF
−5.0 to +2.2
−100
V
dB
±4.95
40
35
V
mA
pF
5
VS = ±2 V
Max
3.3
−100
24
3.5
V
mA
dB
AD8033/AD8034
TA = 25°C, VS = 5 V, RL = 1 kΩ, gain = +2, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Input Overdrive Recovery Time
Output Overdrive Recovery Time
Slew Rate (25% to 75%)
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
Distortion
Second Harmonic
Third Harmonic
Crosstalk, Output to Output
Input Voltage Noise
Input Current Noise
DC PERFORMANCE
Input Offset Voltage
Conditions
Min
Typ
G = +1, VOUT = 0.2 V p-p
G = +2, VOUT = 0.2 V p-p
G = +2, VOUT = 2 V p-p
−3 V to +3 V input
−1.5 V to +1.5 V input, G = +2
G = +2, VOUT = 4 V step
G = +2, VOUT = 2 V step
70
80
32
21
180
200
70
100
MHz
MHz
MHz
ns
ns
V/μs
ns
−80
−84
−70
−80
−86
11
0.7
dBc
dBc
dBc
dBc
dB
nV/√Hz
fA/√Hz
55
fC = 1 MHz, VOUT = 2 V p-p
RL = 500 Ω
RL = 1 kΩ
RL = 500 Ω
RL = 1 kΩ
f = 1 MHz, G = +2
f = 100 kHz
f = 100 kHz
VCM = 0 V
TMIN − TMAX
1
Input Offset Voltage Match
Input Offset Voltage Drift
Input Bias Current
Open-Loop Gain
INPUT CHARACTERISTICS
Common-Mode Input Impedance
Differential Input Impedance
Input Common-Mode Voltage Range
FET Input Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
Power Supply Rejection Ratio
TMIN − TMAX
VOUT = 0 V to 3 V
87
VCM = 1.0 V to 2.5 V
−80
RL = 1 kΩ
0.16 to 4.83
30% overshoot, G = +1, VOUT = 400 mV p-p
4
1
50
92
−80
Rev. D | Page 4 of 24
2
3.5
2.5
30
10
Unit
mV
mV
mV
μV/°C
pA
pA
dB
1000||2.3
1000||1.7
GΩ||pF
GΩ||pF
0 to 2.0
−100
V
dB
0.04 to 4.95
30
25
V
mA
pF
5
VS = ±1 V
Max
3.3
−100
24
3.5
V
mA
dB
AD8033/AD8034
TA = 25°C, VS = ±12 V, RL = 1 kΩ, gain = +2, unless otherwise noted.
Table 3.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Input Overdrive Recovery Time
Output Overdrive Recovery Time
Slew Rate (25% to 75%)
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
Distortion
Second Harmonic
Third Harmonic
Crosstalk, Output to Output
Input Voltage Noise
Input Current Noise
DC PERFORMANCE
Input Offset Voltage
Conditions
Min
Typ
G = +1, VOUT = 0.2 V p-p
G = +2, VOUT = 0.2 V p-p
G = +2, VOUT = 2 V p-p
−13 V to +13 V input
−6.5 V to +6.5 V input, G = +2
G = +2, VOUT = 4 V step
G = +2, VOUT = 2 V step
G = +2, VOUT = 10 V step
65
80
30
21
100
100
80
90
225
MHz
MHz
MHz
ns
ns
V/μs
ns
ns
−80
−82
−70
−82
−86
11
0.7
dBc
dBc
dBc
dBc
dB
nV/√Hz
fA/√Hz
55
fC = 1 MHz, VOUT = 2 V p-p
RL = 500 Ω
RL = 1 kΩ
RL = 500 Ω
RL = 1 kΩ
f = 1 MHz, G = +2
f = 100 kHz
f = 100 kHz
VCM = 0 V
TMIN − TMAX
1
Input Offset Voltage Match
Input Offset Voltage Drift
Input Bias Current
Open-Loop Gain
INPUT CHARACTERISTICS
Common-Mode Input Impedance
Differential Input Impedance
Input Common-Mode Voltage Range
FET Input Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
Power Supply Rejection Ratio
TMIN − TMAX
VOUT = ±8 V
VCM = ±5 V
88
−92
±11.52
30% overshoot, G = +1
4
2
50
96
−85
Rev. D | Page 5 of 24
2
3.5
2.5
24
12
Unit
mV
mV
mV
μV/°C
pA
pA
dB
1000||2.3
1000||1.7
GΩ||pF
GΩ||pF
−12.0 to +9.0
−100
V
dB
±11.84
60
35
V
mA
pF
5
VS = ±2 V
Max
3.3
−100
24
3.5
V
mA
dB
AD8033/AD8034
ABSOLUTE MAXIMUM RATINGS
Rating
26.4 V
See Figure 5
26.4 V
1.4 V
−65°C to +125°C
−40°C to +85°C
300°C
PD = (VS × IS) + (VS/4)2/RL
In single-supply operation with RL referenced to VS−, worst case
is VOUT = VS/2.
2.0
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
MAXIMUM POWER DISSIPATION
1.5
SOT-23-8
1.0
SC70-5
0.5
0
–60
The maximum safe power dissipation in the AD8033/AD8034
packages is limited by the associated rise in junction temperature
(TJ) on the die. The plastic that encapsulates the die locally
reaches the junction temperature. At approximately 150°C,
which is the glass transition temperature, the plastic changes its
properties. Even temporarily exceeding this temperature limit
can change the stresses that the package exerts on the die,
permanently shifting the parametric performance of the AD8033/
AD8034. Exceeding a junction temperature of 175°C for an
extended period can result in changes in silicon devices, potentially
causing failure.
The still-air thermal properties of the package and PCB (θJA),
ambient temperature (TA), and the total power dissipated in the
package (PD) determine the junction temperature of the die.
The junction temperature can be calculated as
TJ = TA + (PD × θJA)
PD is the sum of the quiescent power dissipation and the power
dissipated in the package due to the load drive for all outputs.
The quiescent power is the voltage between the supply pins (VS)
times the quiescent current (IS). Assuming the load (RL) is
referenced to midsupply, the total drive power is VS/2 × IOUT,
some of which is dissipated in the package and some in the load
(VOUT × IOUT). The difference between the total drive power and
the load power is the drive power dissipated in the package
SOIC-8
–40
–20
0
20
40
60
AMBIENT TEMPERATURE (°C)
80
100
02924-005
Parameter
Supply Voltage
Power Dissipation
Common-Mode Input Voltage
Differential Input Voltage
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering 10 sec)
If the rms signal levels are indeterminate, consider the worst case,
when VOUT = VS/4 for RL to midsupply
MAXIMUM POWER DISSIPATION (W)
Table 4.
Figure 5. Maximum Power Dissipation vs.
Ambient Temperature for a 4-Layer Board
Airflow increases heat dissipation, effectively reducing θJA. In
addition, more metal directly in contact with the package leads
from metal traces, through holes, ground, and power planes
reduces the θJA. Care must be taken to minimize parasitic
capacitances at the input leads of high speed op amps as discussed
in the Layout, Grounding, and Bypassing Considerations section.
Figure 5 shows the maximum power dissipation in the package
vs. the ambient temperature for the 8-lead SOIC (125°C/W),
5-lead SC70 (210°C/W), and 8-lead SOT-23 (160°C/W) packages
on a JEDEC standard 4-layer board. θJA values are approximations.
OUTPUT SHORT CIRCUIT
Shorting the output to ground or drawing excessive current for
the AD8033/AD8034 will likely cause catastrophic failure.
ESD CAUTION
PD = Quiescent Power + (Total Drive Power − Load Power)
PD = [VS × IS] + [(VS/2) × (VOUT/RL)] − [VOUT2/RL]
RMS output voltages should be considered. If RL is referenced
to −VS, as in single-supply operation, the total drive power is
VS × IOUT.
Rev. D | Page 6 of 24
AD8033/AD8034
TYPICAL PERFORMANCE CHARACTERISTICS
Default conditions: VS = ±5 V, CL = 5 pF, RL = 1 kΩ, TA = 25°C.
24
21
8
VOUT = 200mV p-p
G = +10
G = +2
7
18
12
5
GAIN (dB)
9
G = +2
6
VOUT = 1V p-p
4
3
3
G = +1
0
VOUT = 4V p-p
2
–3
G = –1
–9
0.1
1
1
100
10
FREQUENCY (MHz)
1000
VOUT = 2V p-p
0
0.1
02924-006
–6
1
10
FREQUENCY (MHz)
100
02924-009
GAIN (dB)
VOUT = 0.2V p-p
6
G = +5
15
Figure 9. Frequency Response for Various Output Amplitudes (See Figure 45)
Figure 6. Small Signal Frequency Response for Various Gains
8
1
VS = +5V
7
0
VS = ±5V
6
5
VS = ±12V
–2
GAIN (dB)
–3
–4
VS = ±12V
1
G = +1
VOUT = 200mV p-p
0.1
1
10
FREQUENCY (MHz)
100
0
1
10
FREQUENCY (MHz)
100
VS = ±12V
6
VS = ±12V
VS = ±5V
VS = +5V
5
GAIN (dB)
VS = ±5V
VS = +5V
–1
–2
–3
4
3
2
–4
1
–5
1
10
FREQUENCY (MHz)
100
G = +2
VOUT = 2V p-p
02924-008
GAIN (dB)
1
7
G = +1
VOUT = 2V p-p
0
–6
0.1
0.1
Figure 10. Small Signal Frequency Response for Various Supplies
(See Figure 45)
Figure 7. Small Signal Frequency Response for Various Supplies
(See Figure 44)
2
G = +2
VOUT = 200mV p-p
02924-010
–6
3
2
02924-007
–5
VS = ±5V
4
0
0.1
Figure 8. Large Signal Frequency Response for Various Supplies
(See Figure 44)
1
10
FREQUENCY (MHz)
100
Figure 11. Large Signal Frequency Response for Various Supplies
(See Figure 45)
Rev. D | Page 7 of 24
02924-011
GAIN (dB)
–1
VS = +5V
AD8033/AD8034
8
10
VOUT = 200mV p-p
G = +1
CL = 100pF
9
6
VOUT = 200mV p-p
G = +2
CL = 100pF
8
CL = 100pF
RSNUB = 25Ω
2
0
6
5
CL = 33pF
CL = 2pF
3
CL = 2pF
2
–4
1
100
10
0
0.1
02924-012
0.1
Figure 12. Small Signal Frequency Response for Various CL (See Figure 44)
8
CF = 0pF
7
CF = 1pF
100
VOUT = 200mV p-p
G = +2
RL = 1kΩ
7
6
6
5
GAIN (dB)
CF = 1.5pF
5
CF = 2pF
4
RL = 500Ω
4
3
3
2
2
1
10
FREQUENCY (MHz)
100
0
0.1
02924-013
0
0.1
Figure 13. Small Signal Frequency Response for Various CF (See Figure 45)
1
10
FREQUENCY (MHz)
100
Figure 16. Small Signal Frequency Response for Various RL (See Figure 45)
100
VOUT = 200mV p-p
VS = ±12V
180
150
80
10
1
G = +1
60
120
40
90
PHASE
20
60
0
30
PHASE (Degrees)
GAIN
G = +2
GAIN (dB)
IMPEDANCE (Ω)
02924-016
1
1
100
10
FREQUENCY (MHz)
Figure 15. Small Signal Frequency Response for Various CL (See Figure 45)
9
VOUT = 200mV p-p
RF = 3kΩ
8 G = +2
1
02924-015
1
FREQUENCY (MHz)
GAIN (dB)
CL = 33pF
4
–2
–6
CL = 51pF
7
GAIN (dB)
GAIN (dB)
4
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
–20
100
02924-014
0.01
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 14. Output Impedance vs. Frequency (See Figure 47)
Figure 17. Open-Loop Response
Rev. D | Page 8 of 24
10M
0
100M
02924-017
0.1
AD8033/AD8034
–40
G = +2
HD3 RL = 500Ω
–50
–60
–60
–70
–70
–80
DISTORTION (dBc)
DISTORTION (dBc)
–50
HD3 RL = 1kΩ
–90
HD2 RL = 500Ω
–100
–110
HD3 G = +2
–90
HD2 G = +2
–100
–110
HD3 G = +1
HD2 RL = 1kΩ
1
FREQUENCY (MHz)
5
–120
0.1
02924-018
–120
0.1
–20
G = +2
HD3 VS = 5V
–50
HD3 VOUT = 10V p-p
–50
–70
DISTORTION (dBc)
DISTORTION (dBc)
G = +2
–40
HD2 V S = 5V
HD3 VS = 24V
–90
5
–30
–60
–80
1
FREQUENCY (MHz)
Figure 21. Harmonic Distortion vs. Frequency for Various Gains
Figure 18. Harmonic Distortion vs. Frequency for Various Loads
(See Figure 45)
–40
HD2 G = +1
–80
02924-021
–40
–100
HD2 VOUT = 20V p-p
HD3 V OUT = 20V p-p
–60
–70
HD2 V OUT = 10V p-p
–80
–90
HD3 VOUT = 2V p-p
–100
HD2 VS = 24V
–110
1
FREQUENCY (MHz)
5
02924-019
–120
0.1
HD2 V OUT = 2V p-p
–120
0.1
Figure 19. Harmonic Distortion vs. Frequency for Various Supply Voltages
(See Figure 45)
1
FREQUENCY (MHz)
Figure 22. Harmonic Distortion vs. Frequency for Various Amplitudes
(See Figure 45), VS = 24 V
1000
80
G = +1
VS = +5V POSITIVE SIDE
PERCENT OVERSHOOT (%)
70
100
60
VS = +5V NEGATIVE SIDE
50
40
VS = ±5V NEGATIVE SIDE
30
20
VS = ±5V POSITIVE SIDE
10
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
1
0M
10M
100M
Figure 20. Voltage Noise vs. Frequency
0
10
30
50
70
CAPACITIVE LOAD (pF)
90
110
Figure 23. Percent Overshoot vs. Capacitive Load (See Figure 44)
Rev. D | Page 9 of 24
02924-023
10
02924-020
NOISE (nV/√Hz)
5
02924-022
–110
AD8033/AD8034
G = +1
20ns/DIV
25mV/DIV
02924-024
38pF
15pF
80mV/DIV
Figure 24. Small Signal Transient Response 5 V (See Figure 44)
80ns/DIV
02924-027
G = +1
Figure 27. Small Signal Transient Response ±5 V (See Figure 44)
G = +1
VOUT = 8V p-p
VOUT = 8V p-p
VOUT = 2V p-p
VOUT = 2V p-p
3V/DIV
320ns/DIV
02924-025
VOUT = 20V p-p
320ns/DIV
3V/DIV
Figure 25. Large Signal Transient Response (See Figure 44)
02924-028
G = +2
VOUT = 20V p-p
Figure 28. Large Signal Transient Response (See Figure 45)
G = –1
G = +1
350ns/DIV
1.5V/DIV
Figure 26. Output Overdrive Recovery (See Figure 46)
VIN
350ns/DIV
Figure 29. Input Overdrive Recovery (See Figure 44)
Rev. D | Page 10 of 24
02924-029
1.5V/DIV
VOUT
VOUT
02924-026
VIN
AD8033/AD8034
VIN = 1V
VIN = 1V
VOUT – 2VIN
+0.1%
+0.1%
02924-030
1.5µs/DIV
2mV/DIV
Figure 33. 0.1% Short-Term Settling Time
7.0
0
6.9
QUIESCENT SUPPLY CURRENT (mA)
–5
–10
–Ib
–20
+Ib
–25
–30
–35
6.6
6.5
VS = ±5V
6.4
6.3
VS = +5V
6.2
6.1
30
35
40
45 50 55 60 65
TEMPERATURE (°C)
70
75
80
85
–20
0
20
40
TEMPERATURE (°C)
80
Figure 34. Quiescent Supply Current vs. Temperature for Various Supply
Voltages
4.0
BJT INPUT RANGE
3.5
30
18
NORMALIZED OFFSET (mV)
–Ib
24
+Ib
12
6
–Ib
VS = ±12V
3.0
2.5
2.0
1.5
1.0
0.5
VS = ±5V
VS = +5V
0
–0.5
0
2
4
6
8
COMMON-MODE VOLTAGE (V)
10
12
02924-032
0
FET INPUT RANGE
10
+Ib
5
0
–5
–10
–15
–20
–25
–30
–12 –10 –8 –6 –4 –2
60
02924-034
25
02924-031
20
5.9
–40
36
Ib (µA)
VS = ±12V
6.0
Figure 31. Ib vs. Temperature
Ib (pA)
6.8
6.7
Figure 32. Ib vs. Common-Mode Voltage Range
–1.0
–14 –12 –10 –8
–6 –4 –2 0
2
4
6
8
COMMON-MODE VOLTAGE (V)
10
12
14
Figure 35. Input Offset Voltage vs. Common-Mode Voltage
Rev. D | Page 11 of 24
02924-035
Ib (pA)
–15
42
–0.1%
20ns/DIV
2mV/DIV
Figure 30. Long-Term Settling Time
–40
VOUT – 2VIN
t=0
02924-033
–0.1%
t=0
AD8033/AD8034
105
–20
100
–30
OPEN-LOOP GAIN (dB)
95
CMRR (dB)
–40
–50
–60
90
RL = 500Ω
85
RL = 1kΩ
RL = 2kΩ
80
75
70
–70
1
10
FREQUENCY (MHz)
100
60
–12 –10
02924-036
–80
0.1
–4 –2
0
2
4
OUTPUT VOLTAGE (V)
6
8
10
12
–40
1.0
–50
0.8
SOT-23 A/B
VCC – VOH
CROSSTALK (dB)
0.6
0.4
VOL – VEE
0.2
–60
SOIC A/B
–70
SOT-23 B/A
SOIC B/A
–80
–90
5
10
15
20
25
30
ILOAD (mA)
–100
0.1
02924-037
0
1
FREQUENCY (MHz)
10
50
02924-040
OUTPUT SATURATION (V)
–6
Figure 39. Open-Loop Gain vs. Output Voltage for Various RL
Figure 36. CMRR vs. Frequency (See Figure 50)
0
–8
02924-039
65
Figure 40. Crosstalk (See Figure 52)
Figure 37. Output Saturation Voltage vs. Load Current
0
180
–10
150
–20
–30
FREQUENCY
PSRR (dB)
–PSRR
–40
–50
+PSRR
–60
120
90
60
–70
–80
30
0.001
0.01
0.1
1
10
100
FREQUENCY (MHz)
Figure 38. PSRR vs. Frequency (See Figure 49 and Figure 51)
0
–1.5
–1.0
–0.5
0
0.5
VOS (mV)
Figure 41. Initial Offset
Rev. D | Page 12 of 24
1.0
1.5
02924-041
–100
0.0001
02924-038
–90
AD8033/AD8034
VOUT
1µs/DIV
1.2V/DIV
VIN
1µs/DIV
Figure 43. G = +2 Response, VS = ±5 V
Figure 42. G = +1 Response, VS = ±5 V
Rev. D | Page 13 of 24
02924-043
VIN
02924-042
1.2V/DIV
VOUT
AD8033/AD8034
TEST CIRCUITS
+VS
+VS
1µF
1µF
+
+
10nF
10nF
RSNUB
VIN
AD8033/AD8034
49.9Ω
976Ω
CLOAD
VOUT
AD8033/AD8034
49.9Ω
10nF
10nF
VSINE
0.2V p-p
02924-047
–VS
–
+
1µF
02924-044
+
1µF
+
–VS
Figure 47. Output Impedance, G = +1
Figure 44. G = +1
CF
1kΩ
1kΩ
RF
+VS
1kΩ
+VS
1µF
1µF
+
+
10nF
499Ω
VIN
49.9Ω
RSNUB
976Ω
AD8033/AD8034
CLOAD
10nF
VOUT
AD8033/AD8034
49.9Ω
10nF
10nF
VSINE
0.2V p-p
–VS
–VS
Figure 45. G = +2
1kΩ
Figure 48. Output Impedance, G = +2
1kΩ
+VS
1µF
+
10nF
976Ω
AD8033/AD8034
499Ω
VOUT
49.9Ω
10nF
+
1µF
–VS
02924-046
VIN
–
+
1µF
02924-045
+
1µF
+
Figure 46. G = −1
Rev. D | Page 14 of 24
02924-048
1kΩ
AD8033/AD8034
1V p-p
+VS
–
+
+VS AC
1µF
+
+VS
49.9Ω
10nF
AD8033/AD8034
VOUT
VOUT
AD8033/AD8034
10nF
02924-049
49.9Ω
–VS AC
+
1µF
02924-051
–VS
1V p-p
+
–
–VS
Figure 49. Negative PSRR
1kΩ
Figure 51. Positive PSRR
1kΩ
1kΩ
1kΩ
–VS
+VS
–
1µF
TO PORT 1 499Ω
+
50Ω
VIN
–
+
49.9Ω
10nF
976Ω
1kΩ
AD8033/AD8034
VOUT
499Ω
TO PORT 2
1kΩ
–VS
+VS
+
49.9Ω
10nF
+
1µF
1kΩ
–VS
A
–
+VS
02924-050
1kΩ
+ B
1kΩ
Figure 50. CMRR
Figure 52. Crosstalk
Rev. D | Page 15 of 24
1kΩ
02924-052
VIN
AD8033/AD8034
THEORY OF OPERATION
The incorporation of JFET devices into the Analog Devices
high voltage XFCB process has enabled the ability to design the
AD8033/AD8034. The AD8033/AD8034 are voltage feedback
rail-to-rail output amplifiers with FET inputs and a bipolarenhanced common-mode input range. The use of JFET devices in
high speed amplifiers extends the application space into both the
low input bias current and low distortion, high bandwidth areas.
Using N-channel JFETs and a folded cascade input topology,
the common-mode input level operates from 0.2 V below the
negative rail to within 3.0 V of the positive rail. Cascading of
the input stage ensures low input bias current over the entire
common-mode range as well as CMRR and PSRR specifications
that are above 90 dB. Additionally, long-term settling issues that
normally occur with high supply voltages are minimized as a
result of the cascading.
OUTPUT STAGE DRIVE AND CAPACITIVE LOAD
DRIVE
The common emitter output stage adds rail-to-rail output
performance and is compensated to drive 35 pF (30% overshoot
at G = +1). Additional capacitance can be driven if a small snub
resistor is put in series with the capacitive load, effectively
decoupling the load from the output stage, as shown in Figure 12.
The output stage can source and sink 20 mA of current within
500 mV of the supply rails and 1 mA within 100 mV of the
supply rails.
INPUT OVERDRIVE
An additional feature of the AD8033/AD8034 is a bipolar input
pair that adds rail-to-rail common-mode input performance
specifically for applications that cannot tolerate phase inversion
problems.
Under normal common-mode operation, the bipolar input
pair is kept reversed, maintaining Ib at less than 1 pA. When
the input common-mode operation comes within 3.0 V of the
positive supply rail, I1 turns off and I4 turns on, supplying tail
current to the bipolar pair Q25 and Q27. With this configuration,
the inputs can be driven beyond the positive supply rail without
any phase inversion (see Figure 53).
As a result of entering the bipolar mode of operation, an offset
and input bias current shift occurs (see Figure 32 and Figure 35).
After re-entering the JFET common-mode range, the amplifier
recovers in approximately 100 ns (refer to Figure 29 for input
overload behavior). Above and below the supply rails, ESD
protection diodes activate, resulting in an exponentially
increasing input bias current. If the inputs are driven well
beyond the rails, series input resistance should be included
to limit the input bias current to