AD8327ARU-REEL

a 5 V CATV Line Driver Coarse Step Output Power Control AD8327 FEATURES Supports DOCSIS Standard for Reverse Path Transmission Gain Programmable in 6.02 dB Steps over a 48.16 dB Range Low Distortion at 60 dBmV Output –63 dBc SFDR at 21 MHz –57 dBc SFDR at 42 MHz Output Noise Level –47 dBmV in 160 kHz Maintains 75 ⍀ Output Impedance Transmit Enable and Transmit Disable Modes Upper Bandwidth: 160 MHz (Full Gain Range) 5 V Supply Operation Supports SPI Interfaces FUNCTIONAL BLOCK DIAGRAM VCC (5 PINS) AD8327 R1 VIN+ DIFF OR SINGLE INPUT AMP VIN– TE DECODE ZIN (SINGLE) = 800⍀ ZIN (DIFF) = 1.6k⍀ 8 DATA LATCH Distortion performance of –63 dBc is achieved with an output level up to 60 dBmV at 21 MHz bandwidth. A key performance and cost advantage of the AD8327 results from the ability to maintain a constant 75 Ω output impedance during Transmit Enable and Transmit Disable conditions. In addition, this device has a sleep mode function that reduces the quiescent current to 5 mA. POWER-DOWN LOGIC CXR 8 SHIFT REGISTER LE O DATEN DATA CLK GND (5 PINS) TXEN SLEEP –50 VOUT = 60dBmV @ MAX GAIN –55 DISTORTION – dBc The AD8327 comprises a digitally controlled variable attenuator of 0 dB to –48.16 dB, which is preceded by a low noise, fixed gain buffer and followed by a low distortion, high power amplifier. The AD8327 accepts a differential or single-ended input signal. The output is specified for driving a 75 Ω load, such as coaxial cable. VOUT ZOUT = 75⍀ 8 B SO The AD8327 is a low-cost, digitally controlled, variable gain amplifier optimized for coaxial line driving applications such as cable modems that are designed to the MCNS-DOCSIS upstream standard. An 8-bit serial word determines the desired output gain over a 48.16 dB range resulting in gain changes of 6.02 dB/major carry. POWER AMP ATTENUATION CORE VERNIER R2 APPLICATIONS Gain-Programmable Line Driver DOCSIS High-Speed Data Modems Interactive Cable Set-Top Boxes PC Plug-in Cable Modems General-Purpose Digitally Controlled Variable Gain Block GENERAL DESCRIPTION BYP HD3 –60 HD2 –65 –70 –75 5 15 25 35 45 55 FUNDAMENTAL FREQUENCY – MHz 65 Figure 1. Harmonic Distortion vs. Frequency The AD8327 is packaged in a low-cost 20-lead TSSOP, operates from a single 5 V supply, and has an operational temperature range of –40°C to +85°C. REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2001 AD8327–SPECIFICATIONS (T = 25ⴗC, V = 5 V, R = 75 ⍀, V A Parameter S L IN(DIFFERENTIAL) Conditions INPUT CHARACTERISTICS Specified AC Voltage Noise Figure Input Resistance = 30 dBmV) Min POUT = 60 dBmV, Max Gain Max Gain, f = 10 MHz Single-Ended Input Differential Input Gain Code = 10000000 (128 Decimal) Gain Code = 00000000 (0 Decimal) All Gain Codes f = 65 MHz All Gain Codes Max Gain, f = 10 MHz 14.8 75 ± 20% Ω –63 –61 –54 –63 –57 –57 –62 dBc dBc dBc dBc dBc dBc dBc ± 0.25 dB Min to Max Gain Max Gain, VIN = 30 dBmV Max Gain, TXEN = 0 V, f = 42 MHz, VIN = 30 dBmV 60 30 –52 ns ns dBc Max Gain, VIN = 0 V Max Gain, VIN = 0 V Max Gain, VIN = 0 V Max Gain, VIN = 0 V Equivalent Output = 31 dBmV Equivalent Output = 60 dBmV 300 40 2 1.7 3 25 2 ns ns µs µs mV p-p mV p-p µs –47 Transmit Disable Mode (TXEN = 0), f = 10 MHz Max Gain, f = 10 MHz Transmit Enable (TXEN = 1) and Transmit Disable Mode (TXEN = 0) –66 f = 21 MHz, VOUT = 60 dBmV @ Max Gain f = 42 MHz, VOUT = 60 dBmV @ Max Gain f = 65 MHz, VOUT = 60 dBmV @ Max Gain f = 21 MHz, VOUT = 60 dBmV @ Max Gain f = 42 MHz, VOUT = 60 dBmV @ Max Gain f = 65 MHz, VOUT = 60 dBmV @ Max Gain Adjacent Channel Width = Transmit Channel Width = 160 KSYM/SEC f = 10 MHz, Code to Code B SO Third Order Harmonic Distortion Adjacent Channel Power Gain Linearity Error Output Settling Due to Gain Change (TGS) Due to Input Change Isolation in Transmit Disable Mode O POWER CONTROL Transmit Enable Settling Time (TON)1 Transmit Disable Settling Time (TOFF)1 Transmit Enable Settling Time (TON)2 Transmit Disable Settling Time (TOFF)2 Between Burst Transients2 Ramp Setting2 POWER SUPPLY Operating Range Quiescent Current 49.16 dB 31 dB –17.16 dB dB/Major Carry 160 0.4 0 –32 LE OVERALL PERFORMANCE Second Order Harmonic Distortion 48.16 30 –18.16 6.02 MHz dB dB dBmV in 160 kHz dBmV in 160 kHz dBmV in 160 kHz dBm Min Gain, f = 10 MHz 1 dB Compression Point Differential Output Impedance 47.16 29 –19.16 Unit dBmV dB Ω Ω pF TE OUTPUT CHARACTERISTICS Bandwidth (–3 dB) Bandwidth Roll-Off Bandwidth Peaking Output Noise Spectral Density Max 30 13.2 800 1600 2 Input Capacitance GAIN CONTROL INTERFACE Gain Range Maximum Gain Minimum Gain Gain Scaling Factor Typ Transmit Enable Mode (TXEN = 1) @ Dec 128 Transmit Enable Mode (TXEN = 1) @ Dec 0 Transmit Disable Mode @ All Gain Codes Sleep Mode @ All Gain Codes OPERATING TEMPERATURE RANGE 4.75 75 40 10 3 –40 5 105 60 15 5 5.25 135 80 20 7 V mA mA mA mA +85 °C NOTES 1 For Transmit Enable or Transmit Disable transitions using a 0 pF capacitor (at CXR pin) to ground. 2 For Transmit Enable or Transmit Disable transitions using a 100 pF capacitor (at CXR pin) to ground. Specifications subject to change without notice. –2– REV. 0 AD8327 LOGIC INPUTS (TTL/CMOS-Compatible Logic) (DATEN, CLK, SDATA, TXEN, SLEEP, V Parameter Min Logic “1” Voltage Logic “0” Voltage Logic “1” Current (VINH = 5 V) CLK, SDATA, DATEN Logic “0” Current (VINL = 0 V) CLK, SDATA, DATEN Logic “1” Current (VINH = 5 V) TXEN Logic “0” Current (VINL = 0 V) TXEN Logic “1” Current (VINH = 5 V) SLEEP Logic “0” Current (VINL = 0 V) SLEEP 2.1 0 0 –600 50 –250 50 –250 TIMING REQUIREMENTS Typ Max Unit 5.0 0.8 20 –100 190 –30 190 –30 V V nA nA µA µA µA µA VALID DATA WORD G1 MSB. . . .LSB VALID DATA WORD G2 B SO SDATA tC tWH CLK tES tEH 8 CLOCK CYCLES DATEN GAIN TRANSFER (G1) GAIN TRANSFER (G2) tOFF TXEN tGS tON ANALOG OUTPUT SIGNAL AMPLITUDE (p-p) Figure 2. Serial Interface Timing VALID DATA BIT SDATA MSB Max Unit 10 ns ns ns ns ns ns ns 16.0 32.0 5.0 15.0 5.0 3.0 LE Clock Pulsewidth (tWH) Clock Period (tC) Setup Time SDATA vs. Clock (tDS) Setup Time DATEN vs. Clock (tES) Hold Time SDATA vs. Clock (tDH) Hold Time DATEN vs. Clock (tEH) Input Rise and Fall Times, SDATA, DATEN, Clock (tR, tF) tDS Typ TE Min O = 5 V: Full Temperature Range) (Full Temperature Range, VCC = 5 V, tR = tF = 4 ns, fCLK = 8 MHz unless otherwise noted.) Parameter MSB-1 tDS MSB-2 tDH CLK Figure 3. SDATA Timing REV. 0 CC –3– AD8327 PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS* Supply Voltage +VS Pins 4, 6, 11, 12, 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Input Voltages Pins 17, 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.5 V Pins 1, 2, 3, 19, 20 . . . . . . . . . . . . . . . . . . . –0.8 V to +5.5 V Internal Power Dissipation TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 810 mW Operating Temperature Range . . . . . . . . . . . –40°C to +85°C Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C Lead Temperature, Soldering 60 seconds . . . . . . . . . . . 300°C 1 20 DATEN CLK 2 19 SLEEP TXEN 3 18 VIN– VCC 4 17 VIN+ GND 5 VCC AD8327 16 VCC TOP VIEW 6 (Not to Scale) 15 GND CXR 7 14 BYP GND 8 13 GND GND 9 12 VCC VOUT 10 11 VCC TE *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. SDATA PIN FUNCTION DESCRIPTIONS Mnemonic Description 1 SDATA 2 CLK 3 4, 6, 11, 12, 16 5, 8, 9, 13, 15 7 10 14 17 TXEN VCC GND CXR VOUT BYP VIN+ 18 19 VIN– SLEEP 20 DATEN Serial Data Input. This digital input allows for an 8-bit serial (gain) word to be loaded into the internal register with the MSB (Most Significant Bit) first. Clock Input. The clock port controls the serial attenuator data transfer rate to the 8-bit masterslave register. A Logic 0-to-1 transition latches the data bit and a 1-to-0 transfers the data bit to the slave. This requires the input serial data word to be valid at or before this clock transition. Logic “0” disables transmission. Logic “1” enables transmission. Common Positive External Supply Voltage. A 0.1 µF capacitor must decouple each pin. Common External Ground Reference Transmit Enable/Disable Timing Capacitor. This pin is decoupled with a 100 pF capacitor to GND. Output Signal Internal Bypass. This pin must be externally ac-coupled (0.1 µF capacitor). Noninverting Input. DC-biased to approximately VCC/2. Should be ac-coupled with a 0.1 µF capacitor. Inverting Input. DC-biased to approximately VCC/2. Should be ac-coupled with a 0.1 µF capacitor. Low Power Sleep Mode. Logic 0 enables Sleep mode, where ZOUT goes to 200 Ω and supply current is reduced to 5 mA. Logic 1 enables normal operation. Data Enable Low Input. This port controls the 8-bit parallel data latch and shift register. A Logic 0-to-1 transition transfers the latched data to the attenuator core (updates the gain) and simultaneously inhibits serial data transfer into the register. A 1-to-0 transition inhibits the data latch (holds the previous gain state) and simultaneously enables the register for serial data load. O B SO LE Pin No. ORDERING GUIDE Model Temperature Range Package Description ␪JA Package Option AD8327ARU AD8327ARU-REEL AD8327-EVAL –40°C to +85°C –40°C to +85°C 20-Lead TSSOP 20-Lead TSSOP Evaluation Board 85°C/W* 85°C/W* RU-20 RU-20 *Thermal Resistance measured on SEMI standard 4-layer board. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8327 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. –4– WARNING! ESD SENSITIVE DEVICE REV. 0 Typical Performance Characteristics–AD8327 0 +VS 10␮F ISOLATION – dBc –20 0.1␮F 0.1␮F VCC VIN– VIN AD8327 165⍀ 0.1␮F VIN+ 0.1␮F BYP CXR –30 –40 –50 –60 –70 75⍀ GND MAX GAIN –80 100pF 0.1␮F TXEN = 0 VIN = 30dBmV –10 MIN GAIN 40 0.6 f = 65MHz 0.5 128D 30 64D LE 0.4 GAIN ERROR – dB 20 0.3 GAIN – dB f = 42MHz 0.2 0.1 0 f = 10MHz –0.3 0 B SO f = 5MHz –0.2 16 10 0 –10 –0.1 32 48 64 80 96 GAIN CONTROL – Decimal Code 112 160 150 1 135 +VS 130 0.1␮F VIN AD8327 165⍀ VIN+ 120 01D 00D 10 100 FREQUENCY – MHz 1000 85 TXEN = 0 80 TXEN = 1 75 70 65 VIN– 125 02D 90 IMPEDANCE – ⍀ O 140 04D TPC 5. AC Response TXEN = 1 145 08D –30 128 TXEN = 0 155 32D 16D –20 TPC 2. Gain Error vs. Gain Control IMPEDANCE – ⍀ 1000 TPC 4. Isolation in Transmit Disable Mode vs. Frequency TPC 1. Basic Test Circuit OUT 0.1␮F GND 0.1␮F 60 75⍀ 55 115 1 10 FREQUENCY – MHz 100 1 10 FREQUENCY – MHz TPC 6. Output Impedance vs. Frequency TPC 3. Input Impedance vs. Frequency REV. 0 100 10 FREQUENCY – MHz 1 TE –90 –5– 100 AD8327 –50 –50 VOUT = 60dBmV @ MAX GAIN VOUT = 61dBmV @ MAX GAIN –55 DISTORTION – dBc DISTORTION – dBc VOUT = 61dBmV @ MAX GAIN –55 VOUT = 60dBmV @ MAX GAIN –60 VOUT = 59dBmV @ MAX GAIN –65 –60 –65 VOUT = 59dBmV @ MAX GAIN –70 –75 VOUT = 58dBmV @ MAX GAIN VOUT = 58dBmV @ MAX GAIN –80 5 15 5 65 25 35 45 55 FUNDAMENTAL FREQUENCY – MHz TPC 7. Second Order Harmonic Distortion vs. Frequency for Various Output Levels LE –60 –65 DISTORTION – dBc DISTORTION – dBc FO = 21MHz VOUT = 60dBmV @ MAX GAIN –55 –60 HD2 –70 –75 –80 16 B SO 0 80 96 32 48 64 GAIN CONTROL – Decimal Code 112 HD2 –65 –70 –75 –75 0 HD3 HD3 16 32 48 64 80 96 GAIN CONTROL – Decimal Code 112 128 TPC 11. Harmonic Distortion vs. Gain Control –50 FO = 65MHz VOUT = 60dBmV @ MAX GAIN –55 HD2 –60 DISTORTION – dBc O –60 –70 –90 FO = 42MHz VOUT = 60dBmV @ MAX GAIN –55 HD2 –85 128 TPC 8. Harmonic Distortion vs. Gain Control –50 –65 –80 HD3 –85 DISTORTION – dBc 65 –50 FO = 5MHz VOUT = 60dBmV @ MAX GAIN –55 –65 HD3 –70 –75 –80 –80 –85 –85 –90 25 35 45 55 FUNDAMENTAL FREQUENCY – MHz TPC 10. Third Order Harmonic Distortion vs. Frequency for Various Output Levels –50 –90 15 TE –70 –90 0 16 80 96 32 48 64 GAIN CONTROL – Decimal Code 112 128 0 TPC 9. Harmonic Distortion vs. Gain Control 16 80 96 32 48 64 GAIN CONTROL – Decimal Code 112 128 TPC 12. Harmonic Distortion vs. Gain Control –6– REV. 0 AD8327 –10 60 CH PWR ACP UP ACP LOW –20 9.0dBm –62dBc –62.5dBc 40 30 –50 20 VOUT – dBmV –30 –40 –60 –70 –80 C11 C11 CENTER 21MHz C0 C0 Cu1 –10 75kHz/DIV Cu1 –30 –40 41.0 SPAN 750kHz TPC 13. Adjacent Channel Power 41.2 41.4 41.6 41.8 42.0 42.2 42.4 FREQUENCY – MHz 42.6 42.8 43.0 TPC 16. Two-Tone Intermodulation Distortion –30 –25 f = 10MHz @ MAX GAIN, TXEN = 1 –30 OUTPUT NOISE – dBmV in 160kHz TXEN = 1 –35 –40 LE –34 –38 –42 –46 0 16 32 48 64 80 96 GAIN CONTROL – Decimal Code 112 35 VOUT = 60dBmV @ MAX GAIN 30 O CL = 20pF 10␮F 20 0.1␮F VCC VIN– VIN 15 0.1␮F AD8327 165⍀ CL VIN+ 0.1␮F 0.1␮F BYP CXR –55 –60 –65 5 GND ALL GAIN CODES, TXEN = 0 15 25 35 45 FREQUENCY – MHz 55 65 120 CL = 0pF +VS 0.1␮F –50 TPC 17. Output Referred Noise vs. Frequency for Various Gain Codes CL = 10pF 25 @ MIN GAIN, TXEN = 1 –75 128 TPC 14. Output Referred Noise vs. Gain Control –45 –70 75⍀ 100pF TXEN = 1 QUIESCENT SUPPLY CURRENT – mA –50 B SO OUTPUT NOISE – dBmV in 160kHz 0 TE –100 GAIN – dB 10 –20 –90 –110 VOUT = 60dBmV @ MAX GAIN 50 110 100 90 80 70 60 CL = 50pF 10 1 100 10 FREQUENCY – MHz 50 1000 0 TPC 15. AC Response for Various Capacitor Loads REV. 0 16 32 48 64 80 96 GAIN CONTROL – Decimal Code 112 TPC 18. Supply Current vs. Gain Code –7– 128 AD8327 which amplifies these currents to the appropriate levels necessary to drive a 75 Ω load. The output stage maintains 75 Ω output impedance, eliminating the need for external matching resistors. APPLICATIONS General Application The AD8327 is primarily intended for use as the upstream power amplifier (PA), also known as a line driver, in DOCSIS (Data Over Cable Service Interface Specification) certified cable modems and CATV set-top boxes. The upstream signal is either a QPSK or QAM signal generated by a DSP, a dedicated QPSK/ QAM modulator, or a DAC. SPI Programming and Gain Adjustment The AD8327 is controlled through a serial peripheral interface (SPI) of three digital data lines: CLK, DATEN, and SDATA. Changing the gain requires eight bits of data to be streamed into the SDATA port. The sequence of loading the SDATA register begins on the falling edge of the DATEN pin, which activates the CLK line. With the CLK line activated, data on the SDATA line is clocked into the serial shift register, Most Significant Bit (MSB) first, on the rising edge of the CLK pulses. The 8-bit data word is latched into the attenuator core on the rising edge of the DATEN line. This provides control over the changes in the output signal level. The serial interface timing for the AD8327 is shown in Figures 2 and 3. The programmable gain range of the AD8327 is –18.16 dB to +30 dB with steps of 6.02 dB per major carry. This provides a total gain range of 48.16 dB. The AD8327 was characterized with a TOKO transformer (TOKO#617DB-A0070) on the input, and the stated gain values account for the losses due to the transformer. Table I shows the possible gain states. TE In all cases the signal must be low-pass filtered before being applied to the PA in order to filter out-of-band noise and higher order harmonics from the amplified signal. Due to the varying distances between the cable modem and the headend, the upstream PA must be capable of varying the output power by applying gain or attenuation. The varying output power of the AD8327 ensures that the signal from the cable modem will have the proper level once it arrives at the headend. The upstream signal path commonly includes a diplexer and cable splitters. The AD8327 has been designed to overcome losses associated with these passive components in the upstream cable path. Circuit Description LE The AD8327 is composed of three analog functions in the powerup or forward mode. The input amplifier (preamp) can be used single-ended or differentially. If the input is used in the differential configuration, it is imperative that the input signals be 180 degrees out of phase and of equal amplitude. The preamp stage drives a DAC, which provides the AD8327’s attenuation (eight bits or 48.16 dB). The signals in the preamp and DAC gain blocks are differential to improve the PSRR and linearity. A differential current is fed from the DAC into the output stage, Input Bias, Impedance, and Termination B SO The VIN+ and VIN– inputs have a dc bias level of VCC/2, therefore the input signal should be ac-coupled using 0.1 µF capacitors as seen in the typical application circuit (see Figure 4). The differential input impedance of the AD8327 is approximately 1.6 kΩ, while the single-ended input impedance is 800 Ω. Table I. Gain States Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Gain 0 1 2 4 8 16 32 64 128 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 –18.16 –12.14 –6.12 –0.10 5.92 11.94 17.96 23.98 30 O Decimal Code –8– REV. 0 AD8327 VCC 10␮F SLEEP ENB 2 3 4 TXEN 0.1␮F 5 6 7 0.1␮F 100pF 8 9 10 0.1␮F AD8327 SDATA CLK TXEN VCC GND VCC 20 ENB SLEEP VIN– VIN+ VCC CXR GND GND VOUT VIN– 19 18 17 ZIN = 150⍀ 165⍀ 16 0.1␮F 15 14 13 12 11 GND BYP GND VCC VCC 0.1␮F VIN+ 0.1␮F 0.1␮F 0.1␮F TE 1 SDATA CLK 0.1␮F TO DIPLEXER ZIN = 75⍀ Figure 4. Typical Application Circuit LE Single-Ended Inverting Input R12 = ZIN ⴛ 800⍀ 800⍀ – ZIN R11 = ZIN ⴛ R12 R12 + ZIN – 1600⍀ – ZIN R13 AD8327 ZIN Figure 6. Single to Differential Input Differential Signal Source The AD8327 evaluation board is also capable of accepting a differential input signal. Remove R11–R12, R14–R15, and R20, and place 0 Ω jumpers for R16–R17. See Table II for common values of R13, or calculate other input configurations using the equation in Figure 7. AD8327 R12 + R13 = ZIN R11 Figure 5. Single-Ended Inverting Input Differential Input from Single-Ended Source O The default configuration of the evaluation board implements a differential signal drive from a single-ended signal source. A TOKO 1:1 transformer is included on the board for this purpose (T3). Enabling the evaluation board for single to differential input conversion requires R11–R12 and R16–R17 to be removed, and 0 Ω jumpers must be installed on the placeholders for R14, R15, and R20. Table II provides typical R13 values for common input configurations. Other input impedances may be calculated using the equation in Figure 6. Refer to Figure 10 for evaluation board schematic. To utilize the transformer for converting a singleended source into a differential signal, the input signal must be applied to VIN+. REV. 0 ZIN ⴛ 1600⍀ VIN+ B SO When operating the AD8327 in a single-ended input mode VIN+ and VIN– should be terminated as illustrated in Figure 5. On the AD8327 evaluation boards, this termination method requires the removal of R13–R16 and R20, as well as the addition of a 0 Ω jumper at R17. Table II shows the correct values for R11 and R12 for some common input configurations. Other input impedance configurations may be accommodated using the equations in Figure 5. The inverting and noninverting inputs of the AD8327 must be balanced for all input configurations R13 = ZIN ⴛ 1600⍀ 1600⍀ – ZIN VIN+ R13 ZIN AD8327 VIN– Figure 7. Differential Input Output Bias, Impedance, and Termination The output of the AD8327 has a dc bias level of approximately VCC/2; therefore, it should be ac-coupled before being applied to the load. The output impedance of the AD8327 is internally maintained at 75 Ω, regardless of whether the amplifier is in transmit enable or transmit disable mode. This eliminates the need for external back termination resistors. If the output signal is being evaluated using standard 50 Ω test equipment, a minimum loss 75 Ω to 50 Ω pad must be used to provide the test circuit with the proper impedance match. –9– AD8327 Asynchronous Power-Down Table II. Common Input Terminations ZIN (⍀) R11 R12 R13 (⍀) 50 75 100 150 Open Open Open Open Open Open Open Open 52.1 78.7 107 165 Single-Ended Input Termination ZIN (⍀) R11 (⍀) R12 (⍀) R13 50 75 25.5 39.2 53.6 82.5 Open Open TE The asynchronous TXEN pin is used to place the AD8327 into between-burst mode, while maintaining a differential output impedance of 75 Ω. Applying Logic 0 to the TXEN pin activates the on-chip reverse amplifier, providing an 86% reduction in consumed power. For 5 V operation, the supply current is typically reduced from 105 mA to 15 mA. In this mode of operation, between-burst noise is minimized and the amplifier can no longer transmit in the upstream direction. In addition to the TXEN pin, the AD8327 also incorporates an asynchronous SLEEP pin, which may be used to further reduce the supply current to approximately 5 mA. Applying Logic 0 to the SLEEP pin places the amplifier into SLEEP mode. Transitioning into or out of SLEEP mode may result in a transient voltage at the output of the amplifier. Differential Input Termination Distortion, Adjacent Channel Power, and DOCSIS The 5 V supply should be delivered to each of the VCC pins via a low impedance power bus to ensure that each pin is at the same potential. The power bus should be decoupled to ground using a 10 µF tantalum capacitor located close to the AD8327ARU. In addition to the 10 µF capacitor, each VCC pin should be individually decoupled to ground with 0.1 µF ceramic chip capacitors located close to the pins. The bypass pin, labeled BYP (Pin 14), should also be decoupled with a 0.1 µF capacitor. The PCB should have a low impedance ground plane covering all unused portions of the board, except in areas of the board where input and output traces are in close proximity to the AD8327. All AD8327 ground pins must be connected to the ground plane to ensure proper grounding of all internal nodes. In order to deliver the DOCSIS required +58 dBmV of QPSK signal and +55 dBmV of 16 QAM signal, the PA is required to deliver up to +60 dBmV and +57 dBmV respectively. This level is required to compensate for losses associated with the diplex filter or other passive components that may be included in the upstream path of cable modems or set-top boxes. It should be noted that the AD8327 was characterized with the TOKO 617DB-A0070 transformer on the input to generate a differential input signal. TPC 7 and TPC 10 show the AD8327 second and third order harmonic distortion performance versus fundamental frequency for various output power levels. These figures are useful for determining the in-band harmonic levels from 5 MHz to 65 MHz. Harmonics higher in frequency (above 42 MHz for DOCSIS and above 65 MHz for EuroDOCSIS) will be sharply attenuated by the low-pass filter function of the diplexer. B SO CXR Pin LE Power Supply The AD8327 features internal circuitry that controls burst transients. This feature uses a 100 pF capacitor connected to Pin 7 of the AD8327, to slow down the turn-on transient and minimize between-burst transients. Another measure of signal integrity is adjacent channel power, commonly referred to as ACP. DOCSIS section 4.2.10.1.1 states, “Spurious emissions from a transmitted carrier may occur in an adjacent channel that could be occupied by a carrier of the same or different symbol rates.” TPC 13 shows the measured ACP for a +57 dBmV 16 QAM signal taken at the output of the AD8327 evaluation board, through a 75 Ω to 50 Ω matching pad (5.7 dB of loss). The transmit channel width and adjacent channel width in TPC 13 correspond to symbol rates of 160 KSYM/S. Table III shows the ACP results for the AD8327 driving a 16 QAM, +57 dBmV signal for all conditions in DOCSIS Table 4-7 “Adjacent Channel Spurious Emissions.” Signal Integrity Layout Considerations O Careful attention to printed circuit board layout details will prevent problems due to board parasitics. Proper RF design techniques are mandatory. The differential input and output traces should be kept as short as possible. It is also critical that all differential signal paths be symmetrical in length and width. In addition, the input and output traces should be kept far apart, to minimize coupling (crosstalk) through the board. Following these guidelines will optimize the overall performance of the AD8327 in all applications. Table III. Adjacent Channel Power Initial Power-Up When the supply voltage is first applied to the AD8327, the gain of the amplifier is initially set to gain code 0. As power is first applied to the amplifier, the TXEN pin should be held low (Logic 0) to prevent forward signal transmission. After power has been applied to the amplifier, the gain can be set to the desired level by following the procedure provided in the SPI Programming and Gain Adjustment section. The TXEN pin can then be brought from Logic 0 to Logic 1, enabling forward signal transmission at the desired gain level. –10– ADJACENT CHANNEL SYMBOL RATE TRANSMIT SYMBOL RATE 160 KSYM/SEC 320 KSYM/SEC 640 KSYM/SEC 1280 KSYM/SEC 2560 KSYM/SEC ACP (dBc) ACP (dBc) ACP (dBc) ACP (dBc) ACP (dBc) 160 KSYM/SEC –62 –63 –65 –66 –66 320 KSYM/SEC –62 –63 –64 –66 –66 640 KSYM/SEC –63 –62 –63 –65 –66 1280 KSYM/SEC –64 –63 –63 –63 –64 2560 KSYM/SEC –66 –63 –63 –62 –63 REV. 0 AD8327 Noise and DOCSIS Running AD8327 Software At minimum gain, the AD8327 output noise spectral density is 11 nV/√Hz measured at 10 MHz. DOCSIS Table 4-8,“Spurious Emissions in 5 MHz to 42 MHz,” specifies the output noise for various symbol rates. The calculated noise in dBmV for 160KSYM/SECOND is: To load the control software, go to START, PROGRAMS, CABDRIVE_27, or select the AD8327.exe from the installed directory. Once loaded, select the proper parallel port to communicate with the AD8327 (Figure 8).  2    20 log   11 nV  × 160 kHz   + 60 = –47 dBmV    Hz       TE Comparing the computed noise power of –47 dBmV to the +8 dBmV signal yields –55 dBc, which meets the required level set forth in DOCSIS Table 4-8. As the AD8327 gain is increased above this minimum value, the output signal increases at a faster rate than the noise, resulting in a signal to noise ratio that improves with gain. In transmit disable mode, the output noise spectral density is 1.3 nV/√Hz, which results in –66 dBmV when computed over 160 KSYM/S. The noise power was measured directly at the output of the AD8327AR-EVAL board. Evaluation Board Features and Operation LE The AD8327 evaluation board (Part #AD8327AR-EVAL) and control software can be used to control the AD8327 upstream cable driver via the parallel port of a PC. A standard printer cable connected between the parallel port of the personal computer is used to feed all the necessary data to the AD8327 using the Windows-based control software. This package provides a means of evaluating the amplifier with a convenient way to program the gain/attenuation, as well as offering easy control of the asynchronous TXEN and SLEEP pins. With this evaluation kit, the AD8327 can be evaluated in either a single-ended or differential input configuration. A schematic of the evaluation board is provided in Figure 10. Figure 8. Parallel Port Selection Controlling Gain/Attenuation of the AD8327 B SO The slide bar controls the gain/attenuation of the AD8327, which is displayed in dB and in V/V. The gain scales 6 dB per major carry. The gain code from the position of the slide bar is displayed in decimal, binary, and hexadecimal (Figure 9). Overshoot on PC Printer Ports The data lines on some PC parallel printer ports have excessive overshoot that may cause communications problems when presented to the CLK pin of the AD8327. The evaluation board was designed to accommodate a series resistor and shunt capacitor (R2 and C5 in Figure 10) to filter the CLK signal if required. Installing Visual Basic Control Software O Install the “CabDrive_27” software by running “setup.exe” on disk one of the AD8327 Evaluation Software. Follow on-screen directions and insert disk two when prompted. Choose installation directory, and then select the icon in the upper left to complete installation. Figure 9. Control Software Interface REV. 0 –11– AD8327 Transmit Enable and Sleep Mode Memory Functions The Transmit Enable and Transmit Disable buttons select the mode of operation of the AD8327 by asserting logic levels on the asynchronous TXEN pin. The Transmit Disable button applies Logic 0 to the TXEN pin, disabling forward transmission while maintaining a 75 Ω back termination. The Transmit Enable button applies Logic 1 to the TXEN pin, enabling the AD8327 for forward transmission. Checking the “Enable SLEEP Mode” checkbox applies logic “0” to the asynchronous SLEEP pin, setting the AD8327 for SLEEP mode. The MEMORY section of the software provides a way to alternate between two gain settings. The “X->M1” button stores the current value of the gain slide bar into memory while the “RM1” button recalls the stored value, returning the gain slide bar to the stored level. The same applies to the “X->M2” and “RM2” buttons. DATEN TP9 VCC C12 10␮F TE TP10 TP11 TP12 SDATA 1 2 3 4 5 6 7 8 9 10 TXEN SLEEP C1 0.1␮F TP1 C2 0.1␮F SDATA DATEN 20 SLEEP 19 CLK TXEN VIN– 18 VIN+ 17 VCC GND VCC 16 GND 15 VCC BYP 14 CXR GND 13 GND VCC 12 GND VCC 11 VOUT TP2 TSSOP20 1 P1 2 P1 3 P1 4 P1 5 P1 6 P1 7 P1 8 P1 9 10 P1 11 P1 12 P1 13 P1 14 P1 15 P1 16 P1 17 P1 18 TP3 R1 0⍀ TP4 TP6 P1 TP5 C4 DNI R2 0⍀ TP7 R3 0⍀ TP8 C6 DNI C5 DNI P1 20 21 P1 22 P1 23 P1 24 P1 25 P1 26 P1 27 P1 28 P1 29 P1 30 P1 31 P1 32 P1 33 P1 34 P1 35 P1 36 R19 DNI R15 0⍀ 6 4 T3 3 2 C8 0.1␮F 3 DNI R11 DNI TOKO1 VIN+ R16 DNI TP22 0⍀ AGND AGND TP16 R20 0⍀ R14 0⍀ HPF 9 TB1 TP14 1 PRI SEC PRI SEC TP24 C15 0.1␮F AGND 2 1 5 R13 78.7⍀ C10 0.1␮F VIN– R21 DNI AGND 4 T4 DEVICE = 2LUGPWR 19 P1 R17 DNI AGND VCC HPP 1 LPP CBL 5 TP21 COM CX6002 3 10–18 DNI AGND R6 DNI R7 0⍀ R8 DNI TP20 CABLE C14 0.1␮F R5 DNI TP15 R9 0⍀ R10 DNI AGND AGND AGND O P1 R12 DNI B SO P1 C11 0.1␮F C7 0.1␮F AGND C3 100pF AGND AGND LE Z1 TP23 C16 0.1␮F AGND CLK Figure 10. Evaluation Board Schematic –12– REV. 0 B SO LE TE AD8327 O Figure 11. Evaluation Board Layout—Top Silkscreen REV. 0 –13– B SO LE TE AD8327 O Figure 12. Evaluation Board Layout—Component Side –14– REV. 0 B SO LE TE AD8327 O Figure 13. Evaluation Board Layout—Internal Ground Plane REV. 0 –15– B SO LE TE AD8327 O Figure 14. Evaluation Board Layout—Internal Power and Ground Plane –16– REV. 0 B SO LE TE AD8327 O Figure 15. Evaluation Board Layout—Circuit Side REV. 0 –17– B SO LE TE AD8327 O Figure 16. Evaluation Board Layout—Bottom Silkscreen –18– REV. 0 AD8327 EVALUATION BOARD BILL OF MATERIALS AD8327 Evaluation Board Rev. B, Single-Ended-to-Differential Input—Revised–February 21, 2001 Description Ref Description 1 1 2 7 11 1 2 1 1 1 1 4 1 1 1 1 4 4 2 2 2 2 10 µF 25 V. ‘D’ size tantalum chip capacitor 100 pF 0603 ceramic chip capacitor 0.1 µF 50 V. 1206 size ceramic chip capacitor 0.1 µF 25 V. 0603 size ceramic chip capacitor 0 Ω 5% 1/8 W. 1206 size chip resistor 78.7 Ω 1% 1/8 W. 1206 size chip resistor Yellow Test Point Red Test Point Black Test Point Centronics-type 36-pin Right-Angle Connector Terminal Block 2-Pos Green ED1973-ND SMA End launch Jack (E F JOHNSON # 142-0701-801) 1:1 Transformer TOKO # 617DB – A0070 PULSE Diplexer* AD8327 (TSSOP) UPSTREAM Cable Driver AD8327 REV. C Evaluation PC board #4–40 × 1/4 inch STAINLESS panhead machine screw #4–40 × 3/4 inch long aluminum round stand-off # 2–56 × 3/8 inch STAINLESS panhead machine screw # 2 steel flat washer # 2 steel internal tooth lockwasher # 2 STAINLESS STEEL hex. machine nut C12 C3 C15, C16 C1, C2, C7–C11 R1–R3, R7, R9, R14, R15, R20 R13 TP23, TP24 TP9 TP10–TP12 (GND) P1 TB1 VIN–, VIN+, CABLE_0, HPF T3 Z2 Z1 Evaluation PC board TE Qty. LE (P1 Hardware) (P1 Hardware) (P1 Hardware) (P1 Hardware) O B SO NOTES *PULSE Diplexer part numbers B5008 (42 MHz), CX6002 (42 MHz), B5009 (65 MHz). DO NOT INSTALL C4, C5, C6, R6, R7, R8, R10–R12, R16, R17, R21, T9, TP1–TP8, TP14–TP16, TP20–TP22. SMA’s TXEN, CLK, SLEEP, DATEN, SDATA, HPF_0, Z2. REV. 0 –19– AD8327 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). C02653–.8–10/01(0) 20-Lead TSSOP (RU-20) 0.260 (6.60) 0.252 (6.40) 20 11 0.177 (4.50) 0.169 (4.30) 0.256 (6.50) 0.246 (6.25) 10 0.006 (0.15) 0.002 (0.05) 0.0256 (0.65) 0.0118 (0.30) BSC 0.0075 (0.19) 0.0079 (0.20) 0.0035 (0.090) 8ⴗ 0ⴗ 0.028 (0.70) 0.020 (0.50) PRINTED IN U.S.A. O B SO LE SEATING PLANE 0.0433 (1.10) MAX TE 1 PIN 1 –20– REV. 0