11-Bit, 200 MSPS,
1.8 V Analog-to-Digital Converter
AD9230-11
FEATURES
FUNCTIONAL BLOCK DIAGRAM
RBIAS
PWDN
AGND
AVDD
AD9230-11
REFERENCE
CML
VIN+
VIN–
DRVDD
DRGND
TRACK-AND-HOLD
ADC
12-BIT
CORE
CLK+
CLK–
12
OUTPUT
STAGING
LVDS
CLOCK
MANAGEMENT
11
D10 TO D0
OR+
OR–
SERIAL PORT
DCO+
DCO–
RESET SCLK SDIO
CSB
07101-001
SNR = 62.5 dBFS @ fIN up to 70 MHz @ 200 MSPS
ENOB of 10.2 @ fIN up to 70 MHz @ 200 MSPS (−1.0 dBFS)
SFDR = −77 dBc @ fIN up to 70 MHz @ 200 MSPS (−1.0 dBFS)
Excellent linearity
DNL = ±0.15 LSB typical
INL = ±0.5 LSB typical
LVDS at 200 MSPS (ANSI-644 levels)
700 MHz full power analog bandwidth
On-chip reference, no external decoupling required
Integrated input buffer and track-and-hold amplifier
Low power dissipation
373 mW @ 200 MSPS (LVDS SDR mode)
328 mW @ 200 MSPS (LVDS DDR mode)
Programmable input voltage range
1.0 V to 1.5 V, 1.25 V nominal
1.8 V analog and digital supply operation
Selectable output data format (offset binary, twos
complement, gray code)
Clock duty cycle stabilizer
Integrated data capture clock
Figure 1.
APPLICATIONS
Wireless and wired broadband communications
Cable reverse path
Communications test equipment
Radar and satellite subsystems
Power amplifier linearization
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD9230-11 is an 11-bit monolithic sampling analog-todigital converter (ADC) optimized for high performance,
low power, and ease of use. The product operates at up to a
200 MSPS conversion rate and is optimized for outstanding
dynamic performance in wideband carrier and broadband
systems. All necessary functions, including a track-and-hold
(T/H) amplifier and voltage reference, are included on the
chip to provide a complete signal conversion solution.
1.
The ADC requires a 1.8 V analog voltage supply and a
differential clock for full performance operation. The digital
outputs are LVDS (ANSI-644) compatible and support twos
complement, offset binary format, or Gray code. A data clock
output is available for proper output data timing.
4.
Fabricated on an advanced CMOS process, the AD9230-11 is
available in a 56-lead lead frame chip scale package, specified
over the industrial temperature range (−40°C to +85°C).
2.
3.
5.
High Performance. Maintains 62.5 dBFS SNR
@ 200 MSPS with a 70 MHz input.
Low Power. Consumes only 373 mW @ 200 MSPS.
Ease of Use. LVDS output data and output clock signal
allow interface to current FPGA technology. The on-chip
reference and sample-and-hold provide flexibility in
system design. Use of a single 1.8 V supply simplifies
system power supply design.
Serial Port Control. Standard serial port interface (SPI)
supports various product functions, such as data formatting,
disabling the clock duty cycle stabilizer, power-down, gain
adjust, and output test pattern generation.
Pin-Compatible Family. 10-bit and 12-bit pin-compatible
family offered as AD9211 and AD9230.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
AD9230-11
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 16
Applications ....................................................................................... 1
Analog Input and Voltage Reference ....................................... 16
Functional Block Diagram .............................................................. 1
Clock Input Considerations ...................................................... 17
General Description ......................................................................... 1
Power Dissipation and Power-Down Mode ........................... 18
Product Highlights ........................................................................... 1
Digital Outputs ........................................................................... 18
Revision History ............................................................................... 2
Timing ......................................................................................... 19
Specifications..................................................................................... 3
RBIAS ........................................................................................... 19
DC Specifications ......................................................................... 3
Configuration Using the SPI ..................................................... 19
AC Specifications.......................................................................... 4
Hardware Interface..................................................................... 20
Digital Specifications ................................................................... 5
Configuration Without the SPI ................................................ 20
Switching Specifications .............................................................. 6
Memory Map .................................................................................. 22
Timing Diagrams.......................................................................... 7
Reading the Memory Map Table .............................................. 22
Absolute Maximum Ratings............................................................ 8
Reserved Locations .................................................................... 22
Thermal Resistance ...................................................................... 8
Default Values ............................................................................. 22
ESD Caution .................................................................................. 8
Logic Levels ................................................................................. 22
Pin Configurations and Function Descriptions ........................... 9
Transfer Register Map ................................................................ 22
Typical Performance Characteristics ........................................... 13
Outline Dimensions ....................................................................... 25
Equivalent Circuits ......................................................................... 15
Ordering Guide .......................................................................... 25
REVISION HISTORY
10/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
AD9230-11
SPECIFICATIONS
DC SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, fIN = −1.0 dBFS, full scale = 1.25 V, DCS enabled, unless otherwise noted.
Table 1.
Parameter 1
RESOLUTION
ACCURACY
No Missing Codes
Offset Error
Gain Error
Differential Nonlinearity (DNL)
Integral Nonlinearity (INL)
TEMPERATURE DRIFT
Offset Error
Gain Error
ANALOG INPUTS (VIN+, VIN−)
Differential Input Voltage Range 2
Input Common-Mode Voltage
Input Resistance (Differential)
Input Capacitance
POWER SUPPLY
AVDD
DRVDD
Supply Currents
IAVDD 3
IDRVDD3/SDR Mode 4
IDRVDD3/DDR Mode 5
Power Dissipation3
SDR Mode4
DDR Mode5
Temp
Full
25°C
Full
25°C
Full
25°C
Full
25°C
Full
Min
Typ
11
Max
Guaranteed
4.2
−12
+12
0.89
−2.2
+4.3
±0.15
−0.4
+0.4
±0.5
−0.5
Full
Full
+0.5
±9
0.019
Unit
Bits
mV
mV
% FS
% FS
LSB
LSB
LSB
LSB
μV/°C
%/°C
Full
Full
Full
25°C
0.98
1.25
1.4
4.3
2
1.5
V p-p
V
kΩ
pF
Full
Full
1.7
1.7
1.8
1.8
1.9
1.9
V
V
152
55
36
164
58
mA
mA
mA
373
338
400
mW
mW
Full
Full
Full
Full
Full
Full
1
See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and an explanation of how these tests were
completed.
2
The input range is programmable through the SPI, and the range specified reflects the nominal values of each setting. See the Memory Map section.
3
IAVDD and IDRVDD are measured with a −1 dBFS, 10.3 MHz sine input at rated sample rate.
4
Single data rate mode; this is the default mode of the AD9230-11.
5
Double data rate mode; user-programmable feature. See the Memory Map section.
Rev. 0 | Page 3 of 28
AD9230-11
AC SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, fIN = −1.0 dBFS, full scale = 1.25 V, DCS enabled, unless otherwise noted. 1
Table 2.
Parameter 2
SNR
fIN = 10 MHz
fIN = 70 MHz
fIN = 170 MHz
SINAD
fIN = 10 MHz
fIN = 70 MHz
fIN = 170 MHz
EFFECTIVE NUMBER OF BITS (ENOB)
fIN = 10 MHz
fIN = 70 MHz
fIN = 170 MHz
WORST HARMONIC (SECOND OR THIRD)
fIN = 10 MHz
fIN = 70 MHz
fIN = 170 MHz
WORST OTHER (SFDR EXCLUDING SECOND AND THIRD)
fIN = 10 MHz
fIN = 70 MHz
fIN = 170 MHz
ANALOG INPUT BANDWIDTH
1
2
Temp
Min
Typ
25°C
Full
25°C
Full
25°C
62.4
62.2
62.2
62.0
62.9
25°C
Full
25°C
Full
25°C
62.3
62.1
62.0
61.8
Max
Unit
dB
dB
dB
dB
dB
62.5
61.8
62.8
61.5
dB
dB
dB
dB
dB
25°C
25°C
25°C
10.3
10.2
10.1
Bits
Bits
Bits
25°C
Full
25°C
Full
25°C
−86
25°C
Full
25°C
Full
25°C
25°C
−88
62.3
−79
−77
−77
−77
−76
dBc
dBc
dBc
dBc
dBc
−84
−79
−82
−81
dBc
dBc
dBc
dBc
dBc
MHz
−76
−84
−82
700
All ac specifications tested by driving CLK+ and CLK− differentially.
See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and an explanation of how these tests were
completed.
Rev. 0 | Page 4 of 28
AD9230-11
DIGITAL SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, fIN = −1.0 dBFS, full scale = 1.25 V, DCS enabled, unless otherwise noted.
Table 3.
Parameter 1
CLOCK INPUTS
Logic Compliance
Internal Common-Mode Bias
Differential Input Voltage
Input Voltage Range
Input Common-Mode Range
High Level Input Voltage (VIH)
Low Level Input Voltage (VIL)
High Level Input Current (IIH)
Low Level Input Current (IIL)
Input Resistance (Differential)
Input Capacitance
LOGIC INPUTS
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Input Current (SDIO)
Logic 0 Input Current (SDIO)
Logic 1 Input Current (SCLK, PWDN, CSB, RESET)
Logic 0 Input Current (SCLK, PWDN, CSB, RESET)
Input Capacitance
LOGIC OUTPUTS 2
VOD Differential Output Voltage
VOS Output Offset Voltage
Output Coding
Temp
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Min
0.2
AGND − 0.3
1.1
1.2
0
−10
−10
16
Typ
Max
CMOS/LVDS/LVPECL
1.2
6
AVDD + 1.6
AVDD
3.6
0.8
+10
+10
20
24
4
Full
Full
Full
Full
Full
Full
25°C
0.8 × AVDD
Full
Full
247
454
1.125
1.375
Twos complement, gray code, or offset binary (default)
0.2 × AVDD
0
−60
55
0
4
1
Unit
V
V p-p
V
V
V
V
μA
μA
kΩ
pF
V
V
μA
μA
μA
μA
pF
mV
V
See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and an explanation of how these tests were
completed.
2
LVDS RTERMINATION = 100 Ω.
Rev. 0 | Page 5 of 28
AD9230-11
SWITCHING SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, fIN = −1.0 dBFS, full scale = 1.25 V, DCS enabled, unless otherwise noted.
Table 4.
Parameter
CONVERSION RATE
Maximum Conversion Rate
Minimum Conversion Rate
PULSE WIDTH
CLK+ Pulse Width High (tCH)
CLK+ Pulse Width Low (tCL)
OUTPUT (LVDS, SDR MODE) 1
Data Propagation Delay (tPD)
Rise Time (tR) (20% to 80%)
Fall Time (tF) (20% to 80%)
DCO Propagation Delay (tCPD)
Data to DCO Skew (tSKEW)
Latency
OUTPUT (LVDS, DDR MODE) 2
Data Propagation Delay (tPD)
Rise Time (tR) (20% to 80%)
Fall Time (tF) (20% to 80%)
DCO Propagation Delay (tCPD)
Data to DCO Skew (tSKEW)
Latency
APERTURE UNCERTAINTY (JITTER, tJ)
1
2
Temp
Min
Full
Full
200
Full
Full
2.25
2.25
Full
25°C
25°C
Full
Full
Full
Full
25°C
25°C
Full
Full
Full
25°C
−0.3
−0.5
See Figure 2.
See Figure 3.
Rev. 0 | Page 6 of 28
Typ
Max
Unit
40
MSPS
MSPS
2.5
2.5
ns
ns
3.8
0.2
0.2
3.9
0.1
6
ns
ns
ns
ns
ns
Cycles
3.8
0.2
0.2
3.9
0.1
6
0.2
0.5
0.3
ns
ns
ns
ns
ns
Cycles
ps rms
AD9230-11
TIMING DIAGRAMS
N–1
tA
N+4
N+5
N
N+3
VIN
N+1
tCH
tCL
N+2
1/fS
CLK+
CLK–
tCPD
DCO+
DCO–
tSKEW
tPD
Dx+
N–5
N–4
N–3
N–2
07101-002
N–6
Dx–
Figure 2. Single Data Rate Mode
N–1
tA
N+4
N+5
N
N+3
VIN
N+1
tCH
tCL
N+2
1/fS
CLK+
CLK–
tCPD
DCO+
DCO–
tSKEW
tPD
D5+
D5
N–7
NO
DATA
D5
N–6
NO
DATA
D5
N–5
NO
DATA
D5
N–4
NO
DATA
D5
N–3
NO
DATA
D10
N–7
D4
N–6
D10
N–6
D4
N–5
D10
N–5
D4
N–4
D10
N–4
D4
N–3
D10
N–3
D4
N–2
D4/D10+
D4/D10–
6 MSBs
5 LSBs
Figure 3. Double Data Rate Mode
Rev. 0 | Page 7 of 28
07101-003
D5–
AD9230-11
ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter
Electrical
AVDD to AGND
DRVDD to DRGND
AGND to DRGND
AVDD to DRVDD
D0+/D0− through D10+/D10−
to DRGND
DCO+/DCO− to DRGND
OR+/OR− to DGND
CLK+ to AGND
CLK− to AGND
VIN+ to AGND
VIN− to AGND
SDIO/DCS to DGND
PWDN to AGND
CSB to AGND
SCLK/DFS to AGND
Environmental
Storage Temperature Range
Operating Temperature Range
Lead Temperature
(Soldering, 10 sec)
Junction Temperature
Rating
−0.3 V to +2.0 V
−0.3 V to +2.0 V
−0.3 V to +0.3 V
−2.0 V to +2.0 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to +3.9 V
−0.3 V to +3.9 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to +3.9 V
−0.3 V to +3.9 V
−0.3 V to +3.9 V
−65°C to +125°C
−40°C to +85°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
The exposed paddle must be soldered to the ground plane
for the LFCSP package. Soldering the exposed paddle to the
customer board increases the reliability of the solder joints,
maximizing the thermal capability of the package.
Table 6.
Package Type
56-Lead LFCSP (CP-56-2)
θJA
30.4
θJC
2.9
Unit
°C/W
Typical θJA and θJC are specified for a 4-layer board in still air.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, metal that is in direct contact with the package leads
reduces the θJA.
ESD CAUTION
150°C
Rev. 0 | Page 8 of 28
AD9230-11
56
55
54
53
52
51
50
49
48
47
46
45
44
43
D1+
D1–
D0+ (LSB)
D0– (LSB)
DNC
DNC
DCO+
DCO–
DRGND
DRVDD
AVDD
CLK–
CLK+
AVDD
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PIN 1
INDICATOR
AD9230-11
TOP VIEW
(Not to Scale)
42
41
40
39
38
37
36
35
34
33
32
31
30
29
AVDD
AVDD
CML
AVDD
AVDD
AVDD
VIN–
VIN+
AVDD
AVDD
AVDD
RBIAS
AVDD
PWDN
NOTES
1. DNC = DO NOT CONNECT.
2. PIN 0 (EXPOSED PADDLE) = AGND.
07101-004
D8–
D8+
D9–
D9+
(MSB) D10–
(MSB) D10+
OR–
OR+
DRGND
DRVDD
SDIO/DCS
SCLK/DFS
CSB
RESET
15
16
17
18
19
20
21
22
23
24
25
26
27
28
D2–
D2+
D3–
D3+
D4–
D4+
DRVDD
DRGND
D5–
D5+
D6–
D6+
D7–
D7+
Figure 4. Single Data Rate Mode Pin Configuration
Table 7. Single Data Rate Mode Pin Function Descriptions
Pin No.
30, 32 to 34, 37 to 39, 41 to
43, 46
7, 24, 47
0
8, 23, 48
35
36
40
Mnemonic
AVDD
Description
1.8 V Analog Supply.
DRVDD
AGND 1
DRGND1
VIN+
VIN−
CML
44
45
31
28
25
CLK+
CLK−
RBIAS
RESET
SDIO/DCS
26
27
29
49
50
51, 52
53
54
55
56
1
2
SCLK/DFS
CSB
PWDN
DCO−
DCO+
DNC
D0− (LSB)
D0+ (LSB)
D1−
D1+
D2−
D2+
1.8 V Digital Output Supply.
Analog Ground. The exposed paddle should be connected to the analog ground.
Digital Output Ground.
Analog Input (True).
Analog Input (Complement).
Common-Mode Output Pin. Enabled through the SPI, this pin provides a reference for the
optimized internal bias voltage for VIN+/VIN−.
Clock Input (True).
Clock Input (Complement).
Set Pin for Chip Bias Current. Place 1% 10 kΩ resistor terminated to ground. Nominally 0.5 V.
CMOS-Compatible Chip Reset (Active Low).
Serial Port Interface (SPI) Data Input/Output (Serial Port Mode). Duty Cycle Stabilizer Select
(External Pin Mode).
Serial Port Interface Clock (Serial Port Mode). Data Format Select Pin (External Pin Mode).
Serial Port Chip Select (Active Low).
Chip Power-Down.
Data Clock Output (Complement).
Data Clock Output Input (True).
Do No Connect.
D0 Complement Output Bit (LSB).
D0 True Output Bit (LSB).
D1 Complement Output Bit.
D1 True Output Bit.
D2 Complement Output Bit.
D2 True Output Bit.
Rev. 0 | Page 9 of 28
AD9230-11
Pin No.
3
4
5
6
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1
Mnemonic
D3−
D3+
D4−
D4+
D5−
D5+
D6−
D6+
D7−
D7+
D8−
D8+
D9−
D9+
D10− (MSB)
D10+ (MSB)
OR−
OR+
Description
D3 Complement Output Bit.
D3 True Output Bit.
D4 Complement Output Bit.
D4 True Output Bit.
D5 Complement Output Bit.
D5 True Output Bit.
D6 Complement Output Bit.
D6 True Output Bit.
D7 Complement Output Bit.
D77 True Output Bit.
D8 Complement Output Bit.
D8 True Output Bit.
D9 Complement Output Bit.
D9 True Output Bit.
D10 Complement Output Bit (MSB).
D10 True Output Bit (MSB).
Overrange Complement Output Bit.
Overrange True Output Bit.
AGND and DRGND should be tied to a common quiet ground plane.
Rev. 0 | Page 10 of 28
56
55
54
53
52
51
50
49
48
47
46
45
44
43
D1/D7+
D1/D7–
D0/D6+ (LSB)
D0/D6– (LSB)
ND/D5+
ND/D5–
DCO+
DCO–
DRGND
DRVDD
AVDD
CLK–
CLK+
AVDD
AD9230-11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PIN 1
INDICATOR
AD9230-11
TOP VIEW
(Not to Scale)
42
41
40
39
38
37
36
35
34
33
32
31
30
29
AVDD
AVDD
CML
AVDD
AVDD
AVDD
VIN–
VIN+
AVDD
AVDD
AVDD
RBIAS
AVDD
PWDN
NOTES
1. DNC = DO NOT CONNECT.
2. PIN 0 (EXPOSED PADDLE) = AGND.
07101-005
DNC
DNC
DNC
DNC
DNC
DNC
DNC/(OR–)
DNC/(OR+)
DRGND
DRVDD
SDIO/DCS
SCLK/DFS
CSB
RESET
15
16
17
18
19
20
21
22
23
24
25
26
27
28
D2/D8–
D2/D8+
D3/D9–
D3/D9+
(MSB) D4/D10–
(MSB) D4/D10+
DRVDD
DRGND
OR–
OR+
DNC
DNC
DNC
DNC
Figure 5. Double Data Rate Mode Pin Configuration
Table 8. Double Data Rate Mode Pin Function Descriptions
Pin No.
30, 32 to 34, 37 to 39,
41 to 43, 46
7, 24, 47
0
8, 23, 48
35
36
40
Mnemonic
AVDD
Description
1.8 V Analog Supply.
DRVDD
AGND 1
DRGND1
VIN+
VIN−
CML
44
45
31
28
25
CLK+
CLK−
RBIAS
RESET
SDIO/DCS
26
SCLK/DFS
27
29
49
50
51
52
53
54
55
56
1
2
CSB
PWDN
DCO−
DCO+
ND/D5−
ND/D5+
D0/D6− (LSB)
D0/D6+ (LSB)
D1/D7−
D1/D7+
D2/D8−
D2/D8+
1.8 V Digital Output Supply.
Analog Ground. The exposed paddle should be connected to the analog ground.
Digital Output Ground.
Analog Input Input (True).
Analog Input (Complement).
Common-Mode Output Pin. Enabled through the SPI, this pin provides a reference for the
optimized internal bias voltage for VIN+/VIN−.
Clock Input Input (True).
Clock Input (Complement).
Set Pin for Chip Bias Current. Place 1% 10 kΩ resistor terminated to ground. Nominally 0.5 V.
CMOS-Compatible Chip Reset (Active Low).
Serial Port Interface (SPI) Data Input/Output (Serial Port Mode).
Duty Cycle Stabilizer Select (External Pin Mode).
Serial Port Interface Clock (Serial Port Mode).
Data Format Select Pin (External Pin Mode).
Serial Port Chip Select (Active Low).
Chip Power-Down.
Data Clock Output (Complement).
Data Clock Output Input (True).
ND/D5 Complement Output Bit.
ND/D5 True Output Bit.
D0/D6 Complement Output Bit (LSB).
D0/D6 True Output Bit (LSB).
D1/D7 Complement Output Bit.
D1/D7 True Output Bit.
D2/D8 Complement Output Bit.
D2/D8 True Output Bit.
Rev. 0 | Page 11 of 28
AD9230-11
Pin No.
3
4
5
6
9
Mnemonic
D3/D9−
D3/D9+
D4/D10− (MSB)
D4/D10+ (MSB)
OR−
10
11 to 20
21
OR+
DNC
DNC/(OR−)
22
DNC/(OR+)
1
Description
D3/D9 Complement Output Bit.
D3/D9 True Output Bit.
D4/D10 Complement Output Bit (MSB).
D4/D10 True Output Bit (MSB).
OR Complement Output Bit. This pin is disabled if Pin 21 is reconfigured through the SPI to be
OR−.
OR True Output Bit. This pin is disabled if Pin 22 is reconfigured through the SPI to be OR+.
Do Not Connect.
Do Not Connect. This pin can be reconfigured as the Overrange Complement Output Bit
through the serial port register.
Do Not Connect. This pin can be reconfigured as the Overrange True Output Bit through the
serial port register.
AGND and DRGND should be tied to a common quiet ground plane.
Rev. 0 | Page 12 of 28
AD9230-11
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = 1.8 V, DRVDD = 1.8 V, rated sample rate, DCS enabled, TA = 25°C, 1.25 V p-p differential input, AIN = −1 dBFS, unless
otherwise noted.
0
85
200MSPS
10.3MHz @ –1.0dBFS
SNR: 62.9dB
ENOB: 10.3 BITS
SFDR: 86dBc
–40
80
SNR (dB) +85°C
75
SNR/SFDR (dB)
AMPLITUDE (dBFS)
–20
–60
–80
70
SFDR (dBc) +25°C
65
–100
60
–120
55
SFDR (dBc) –40°C
SNR (dB) +25°C
0
10
20
30
40
50
60
70
80
90
100
FREQUENCY (MHz)
50
07101-028
–140
50
100
150
200
250
300
350
400
450
ANALOG INPUT FREQUENCY (MHz)
Figure 9. Single-Tone SNR/SFDR vs. Input Frequency (fIN)
with 1.25 V p-p Full-Scale; 200 MSPS
Figure 6. 64k Point Single-Tone FFT; 200 MSPS, 10.3 MHz
100
0
200MSPS
70.3MHz @ –1.0dBFS
SNR: 62.5dB
ENOB: 10.2 BITS
SFDR: 77dBc
–20
–40
SFDR (dBFS)
90
80
70
SNR/SFDR (dB)
AMPLITUDE (dBFS)
0
07101-031
SNR (dB) –40°C
–60
–80
SNR (dBFS)
60
50
40
30
–100
SFDR (dBc)
SNR (dB)
20
–120
10
20
30
40
50
60
70
80
90
100
FREQUENCY (MHz)
0
–90
–60
–50
–40
–30
–20
–10
0
Figure 10. SNR/SFDR vs. Input Amplitude; 140.3 MHz
6.0
0
200MSPS
170.3MHz @ –1.0dBFS
SNR: 61.3dB
ENOB: 10.1 BITS
SFDR: 73dBc
–20
5.0
OFFSET (mV)
–40
5.5
–60
–80
–100
4.5
4.0
3.5
3.0
–120
0
10
20
30
40
50
60
70
80
90
FREQUENCY (MHz)
100
2.0
–40 –30 –20 –10
0
10
20
30
40
50
60
TEMPERATURE (°C)
Figure 11. Offset vs. Temperature
Figure 8. 64k Point Single-Tone FFT; 170 MSPS, 140.3 MHz
Rev. 0 | Page 13 of 28
70
80
90
07101-012
2.5
07101-030
AMPLITUDE (dBFS)
–70
AMPLITUDE (dBFS)
Figure 7. 64k Point Single-Tone FFT; 200 MSPS, 70.3 MHz
–140
–80
07101-032
0
07101-029
–140
10
1.0
0.8
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0
–0.2
–0.2
–0.4
–0.4
–0.6
–0.6
–0.8
–0.8
–1.0
0
512
1024
2048
1536
OUTPUT CODE
Figure 12. DNL
2.0
1.5
1.0
0.5
–40
–20
0
20
40
60
TEMPERATURE (°C)
80
100
120
07101-013
0
–0.5
–60
–1.0
0
512
1024
OUTPUT CODE
Figure 14. INL
2.5
GAIN (%FS)
0
Figure 13. Gain vs. Temperature
Rev. 0 | Page 14 of 28
1536
2048
07101-033
INL (LSB)
1.0
07101-034
DNL (LSB)
AD9230-11
AD9230-11
EQUIVALENT CIRCUITS
AVDD
AVDD
25kΩ
1kΩ
CSB
1.2V
10kΩ
CLK–
07101-006
07101-009
10kΩ
CLK+
Figure 18. Equivalent CSB Input Circuit
Figure 15. Clock Inputs
AVDD
DRVDD
VIN+
BUF
AVDD
2kΩ
AVDD
BUF
VCML
~1.4V
V+
2kΩ
VIN–
V–
Dx–
Dx+
V–
V+
07101-007
07101-010
BUF
Figure 16. Analog Inputs (VCML = ~1.4 V)
Figure 19. LVDS Outputs (Dx+, Dx−, OR+, OR−, DCO+, DCO−)
AVDD
SCLK/DFS
RESET
PWDN
25kΩ
DRVDD
1kΩ
1kΩ
SDIO/DCS
07101-008
07101-011
25kΩ
Figure 17. Equivalent SCLK/DFS, RESET, PWDN Input Circuit
Figure 20. Equivalent SDIO/DCS Input Circuit
Rev. 0 | Page 15 of 28
AD9230-11
THEORY OF OPERATION
Differential Input Configurations
The AD9230-11 architecture consists of a front-end sampleand-hold amplifier (SHA) followed by a pipelined switched
capacitor ADC. The quantized outputs from each stage are
combined into a final 11-bit result in the digital correction
logic. The pipelined architecture permits the first stage to
operate on a new input sample, while the remaining stages operate
on preceding samples. Sampling occurs on the rising edge of the
clock.
Optimum performance is achieved while driving the AD9230-11
in a differential input configuration. For baseband applications,
the AD8138 differential driver provides excellent performance
and a flexible interface to the ADC. The output common-mode
voltage of the AD8138 is easily set to AVDD/2 + 0.5 V, and the
driver can be configured in a Sallen-Key filter topology to
provide band limiting of the input signal.
1V p-p
49.9Ω
499Ω
523Ω
AD8138
VIN–
33Ω
Figure 21. Differential Input Configuration Using the AD8138
At input frequencies in the second Nyquist zone and above, the
performance of most amplifiers may not be adequate to achieve the
true performance of the AD9230-11. This is especially true in IF
undersampling applications where frequencies in the 70 MHz to
100 MHz range are being sampled. For these applications, differential transformer coupling is the recommended input configuration.
The signal characteristics must be considered when selecting a
transformer. Most RF transformers saturate at frequencies below a
few megahertz and excessive signal power can also cause core
saturation, leading to distortion. In any configuration, the value of
the shunt capacitor, C, is dependent on the input frequency and
may need to be reduced or removed.
The analog input to the AD9230-11 is a differential buffer. For
best dynamic performance, the source impedances driving
VIN+ and VIN− should be matched such that common-mode
settling errors are symmetrical. The analog input is optimized
to provide superior wideband performance and requires that
the analog inputs be driven differentially. SNR and SINAD
performance degrades significantly if the analog input is driven
with a single-ended signal.
15Ω
1.25V p-p
A wideband transformer, such as Mini-Circuits® ADT1-1WT, can
provide the differential analog inputs for applications that require a
single-ended-to-differential conversion. Both analog inputs are selfbiased by an on-chip resistor divider to a nominal 1.4 V. An
internal differential voltage reference creates positive and negative
reference voltages that define the 1.25 V p-p fixed span of the ADC
core. This internal voltage reference can be adjusted by means of
SPI control. See the Configuration Using the SPI section.
50Ω
2pF
8, 13
11
0.1µF
R
VIN+
200Ω
AD8352
RG
3
10
0.1µF
200Ω
C
AD9230-11
R
4
ANALOG INPUT
5
0.1µF 0Ω
VIN– CML
14
0.1µF
0.1µF
Figure 23. Differential Input Configuration Using the AD8352
Rev. 0 | Page 16 of 28
07101-016
RD
07101-015
As an alternative to using a transformer-coupled input at frequencies in the second Nyquist zone, the AD8352 differential driver can
be used (see Figure 23).
2
CD
AD9230-11
Figure 22. Differential Transformer—Coupled Configuration
0.1µF
1
VIN+
VIN–
15Ω
0.1µF
VCC
ANALOG INPUT
CML
499Ω
ANALOG INPUT AND VOLTAGE REFERENCE
0Ω 16
AD9230-11
20pF
0.1µF
The input stage contains a buffered differential SHA that can
be ac- or dc-coupled. The output staging block aligns the data,
carries out the error correction, and passes the data to the output buffers. The output buffers are powered from a separate
supply, allowing adjustment of the output voltage swing. During
power-down, the output buffers go into a high impedance state.
0.1µF
AVDD
VIN+
33Ω
499Ω
07101-014
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched capacitor DAC
and interstage residue amplifier (MDAC). The residue amplifier
magnifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each stage to facilitate digital correction
of flash errors. The last stage simply consists of a flash ADC.
AD9230-11
CLOCK INPUT CONSIDERATIONS
For optimum performance, the AD9230-11 sample clock inputs
(CLK+ and CLK−) should be clocked with a differential signal.
This signal is typically ac-coupled into the CLK+ pin and the
CLK− pin via a transformer or capacitors. These pins are biased
internally and require no additional bias.
Figure 24 shows a preferred method for clocking the AD9230-11.
The low jitter clock source is converted from single-ended to
differential using an RF transformer. The back-to-back Schottky
diodes across the secondary transformer limit clock excursions
into the AD9230-11 to approximately 0.8 V p-p differential. This
helps prevent the large voltage swings of the clock from feeding
through to other portions of the AD9230-11 and preserves the
fast rise and fall times of the signal, which are critical to low
jitter performance.
In some applications, it is acceptable to drive the sample clock
inputs with a single-ended CMOS signal. In such applications,
CLK+ should be directly driven from a CMOS gate, and the
CLK− pin should be bypassed to ground with a 0.1 μF capacitor
in parallel with a 39 kΩ resistor (see Figure 27). Although the
CLK+ input circuit supply is AVDD (1.8 V), this input is
designed to withstand input voltages up to 3.3 V (as shown in
Figure 28), making the selection of the drive logic voltage very
flexible.
CLOCK
INPUT
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
0.1µF
CLK
50Ω*
CMOS DRIVER
OPTIONAL
0.1µF
100Ω
ADC
AD9230-11
CLK
0.1µF
CLK–
0.1µF
0.1µF
CLOCK
INPUT
50Ω
39kΩ
07101-020
MINI-CIRCUITS
ADT1–1WT, 1:1Z
0.1µF
XFMR
CLK+
*50Ω RESISTOR IS OPTIONAL.
CLK+
Figure 27. Single-Ended 1.8 V CMOS Sample Clock
ADC
100Ω
AD9230-11
0.1µF
CLK–
07101-017
SCHOTTKY
DIODES:
HSM2812
Figure 24. Transformer-Coupled Differential Clock
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
0.1µF
0.1µF
CLOCK
INPUT
CLK+
100Ω
0.1µF
ADC
AD9230-11
CLK–
240Ω
07101-018
240Ω
50Ω*
*50Ω RESISTORS ARE OPTIONAL.
Figure 25. Differential PECL Sample Clock
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
0.1µF
0.1µF
CLK+
CLK
0.1µF
CLOCK
INPUT
LVDS DRIVER
0.1µF
CLK
50Ω*
100Ω
ADC
AD9230-11
CLK–
50Ω*
*50Ω RESISTORS ARE OPTIONAL.
Figure 26. Differential LVDS Sample Clock
07101-019
CLOCK
INPUT
CMOS DRIVER
OPTIONAL
0.1µF
100Ω
CLK
0.1µF
CLK+
ADC
0.1µF
AD9230-11
CLK–
*50Ω RESISTOR IS OPTIONAL.
Clock Duty Cycle Considerations
0.1µF
CLK
50Ω*
CLK
Figure 28. Single-Ended 3.3 V CMOS Sample Clock
CLK
PECL DRIVER
0.1µF
50Ω*
If a low jitter clock is available, another option is to ac couple
a differential PECL signal to the sample clock input pins as
shown in Figure 25. The AD9510/AD9511/AD9512/AD9513/
AD9514/AD9515 family of clock drivers offers excellent jitter
performance.
CLOCK
INPUT
CLOCK
INPUT
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
07101-021
0.1µF
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals. As a result, these ADCs may
be sensitive to clock duty cycle. Commonly, a 5% tolerance is
required on the clock duty cycle to maintain dynamic performance
characteristics. The AD9230-11 contains a duty cycle stabilizer
(DCS) that retimes the nonsampling edge, providing an internal
clock signal with a nominal 50% duty cycle. This allows a wide
range of clock input duty cycles without affecting the performance of the AD9230-11. When the DCS is on, noise and distortion
performance are nearly flat for a wide range of duty cycles.
However, some applications may require the DCS function to
be off. If so, keep in mind that the dynamic range performance can
be affected when operated in this mode. See the Configuration
Using the SPI section for more details on using this feature.
The duty cycle stabilizer uses a delay-locked loop (DLL) to
create the nonsampling edge. As a result, any changes to the
sampling frequency require approximately eight clock cycles
to allow the DLL to acquire and lock to the new rate.
Rev. 0 | Page 17 of 28
AD9230-11
Clock Jitter Considerations
DIGITAL OUTPUTS
High speed, high resolution ADCs are sensitive to the quality of the
clock input. The degradation in SNR at a given input frequency
(fA) due only to aperture jitter (tJ) can be calculated by
Digital Outputs and Timing
SNR Degradation = 20 × log10[1/2 × π × fA × tJ]
In this equation, the rms aperture jitter represents the root mean
square of all jitter sources, including the clock input, analog input
signal, and ADC aperture jitter specifications. IF undersampling
applications are particularly sensitive to jitter (see Figure 29).
Treat the clock as an analog signal in cases where aperture jitter
may affect the dynamic range of the AD9230-11. Power supplies
for clock drivers should be separated from the ADC output
driver supplies to avoid modulating the clock signal with digital
noise. Low jitter, crystal-controlled oscillators make the best
clock sources. If the clock is generated from another type of
source (by gating, dividing, or other methods), it should be
retimed by the original clock at the last step.
Refer to the AN-501 Application Note and the AN-756
Application Note for more in-depth information about jitter
performance as it relates to ADCs (visit www.analog.com).
RMS CLOCK JITTER REQUIREMENT
120
16 BITS
90
14 BITS
80
An example of the LVDS output using the ANSI standard (default)
data eye and a time interval error (TIE) jitter histogram with
trace lengths less than 24 inches on regular FR-4 material is
shown in Figure 30. Figure 31 shows an example of when the
trace lengths exceed 24 inches on regular FR-4 material. Notice
that the TIE jitter histogram reflects the decrease of the data eye
opening as the edge deviates from the ideal position. It is up to
the user to determine if the waveforms meet the timing budget
of the design when the trace lengths exceed 24 inches.
12 BITS
70
10 BITS
60
8 BITS
50
40
30
1
0.125ps
0.25ps
0.5ps
1.0ps
2.0ps
10
100
ANALOG INPUT FREQUENCY (MHz)
1000
14
500
12
400
Figure 29. Ideal SNR vs. Input Frequency and Jitter
The power dissipated by the AD9230-11 is proportional to its
sample rate. The digital power dissipation does not vary much
because it is determined primarily by the DRVDD supply and
bias current of the LVDS output drivers.
By asserting PWDN (Pin 29) high, the AD9230-11 is placed in
standby mode or full power-down mode, as determined by the
contents of Register 0x08. Reasserting the PWDN pin low
returns the AD9230-11 to its normal operational mode.
An additional standby mode is supported by means of varying
the clock input. When the clock rate falls below 20 MHz, the
AD9230-11 assumes a standby state. In this case, the biasing
network and internal reference remain on, but digital circuitry
is powered down. Upon reactivating the clock, the AD9230-11
resumes normal operation after allowing for the pipeline
latency.
VOLTAGE (mV)
300
POWER DISSIPATION AND POWER-DOWN MODE
200
100
0
–100
–200
–300
–400
10
8
6
4
2
–500
–3
–2
–1
0
1
TIME (ns)
2
3
0
–40
–20
0
TIME (ps)
20
40
07101-023
100
07101-022
SNR (dB)
110
The AD9230-11 LVDS outputs facilitate interfacing with LVDS
receivers in custom ASICs and FPGAs that have LVDS capability
for superior switching performance in noisy environments.
Single point-to-point net topologies are recommended with a
100 Ω termination resistor placed as close to the receiver as
possible. No far-end receiver termination and poor differential
trace routing may result in timing errors. It is recommended
that the trace length is no longer than 24 inches and that the
differential output traces are kept close together and at equal
lengths.
TIE JITTER HISTOGRAM (Hits)
130
The AD9230-11 differential outputs conform to the ANSI-644
LVDS standard on default power-up. This can be changed to a
low power, reduced signal option similar to the IEEE 1596.3
standard using the SPI. This LVDS standard can further reduce
the overall power dissipation of the device, which reduces the
power by ~39 mW. See the Memory Map section for more
information. The LVDS driver current is derived on-chip and
sets the output current at each output equal to a nominal
3.5 mA. A 100 Ω differential termination resistor placed at the
LVDS receiver inputs results in a nominal 350 mV swing at the
receiver.
Figure 30. Data Eye for LVDS Outputs in ANSI Mode with Trace Lengths Less
than 24 Inches on Standard FR-4
Rev. 0 | Page 18 of 28
600
12
400
10
200
0
–200
OR DATA OUTPUTS
1 1111 1111
0 1111 1111
0 1111 1111
+FS – 1 LSB
OR
–FS + 1/2 LSB
8
0
0
1
6
0000 0000
0000 0000
0000 0000
–FS
–FS – 1/2 LSB
4
+FS
+FS – 1/2 LSB
07101-025
TIE JITTER HISTOGRAM (Hits)
Figure 32. OR Relation to Input Voltage and Output Data
–400
2
TIMING
–600
–3
0
–100
The AD9230-11 provides latched data outputs with a pipeline
delay of seven clock cycles. Data outputs are available one
propagation delay (tPD) after the rising edge of the clock signal.
–2
–1
0
1
TIME (ns)
2
3
0
07101-024
VOLTAGE (mV)
AD9230-11
100
TIME (ps)
Figure 31. Data Eye for LVDS Outputs in ANSI Mode with Trace Lengths
Greater than 24 Inches on Standard FR-4
The format of the output data is offset binary by default. An
example of the output coding format can be found in Table 12.
If it is desired to change the output data format to twos complement, see the Configuration Using the SPI section.
The length of the output data lines and loads placed on them
should be minimized to reduce transients within the AD9230-11.
These transients can degrade the dynamic performance of the
converter. The AD9230-11 also provides data clock output (DCO)
intended for capturing the data in an external register. The data
outputs are valid on the rising edge of DCO.
An output clock signal is provided to assist in capturing data
from the AD9230-11. The DCO is used to clock the output
data and is equal to the sampling clock (CLK) rate. In single
data rate mode (SDR), data is clocked out of the AD9230-11
and must be captured on the rising edge of the DCO. In double
data rate mode (DDR), data is clocked out of the AD9230-11
and must be captured on the rising and falling edges of the
DCO See the timing diagrams shown in Figure 2 and Figure 3
for more information.
The lowest typical conversion rate of the AD9230-11 is 40 MSPS.
At clock rates below 1 MSPS, the AD9230-11 assumes the
standby mode.
Output Data Rate and Pinout Configuration
CONFIGURATION USING THE SPI
The output data of the AD9230-11 can be configured to drive
12 pairs of LVDS outputs at the same rate as the input clock
signal (single data rate, or SDR, mode), or six pairs of LVDS
outputs at 2× the rate of the input clock signal (double data rate,
or DDR, mode). SDR is the default mode; the device can be
reconfigured for DDR by setting Bit 3 in Register 14 (see Table 13).
The AD9230-11 SPI allows the user to configure the converter for
specific functions or operations through a structured register space
inside the ADC. This gives the user added flexibility to customize
device operation depending on the application. Addresses are
accessed (programmed or readback) serially in 1-byte words. Each
byte may be further divided down into fields, which are
documented in the Memory Map section.
Out-of-Range (OR)
An out-of-range condition exists when the analog input voltage
is beyond the input range of the ADC. OR is a digital output
that is updated along with the data output corresponding to the
particular sampled input voltage. Thus, OR has the same
pipeline latency as the digital data. OR is low when the analog
input voltage is within the analog input range and high when
the analog input voltage exceeds the input range, as shown in
Figure 32. OR remains high until the analog input returns to
within the input range and another conversion is completed. By
logically AND-ing OR with the MSB and its complement, overrange high or underrange low conditions can be detected.
RBIAS
The AD9230-11 requires the user to place a 10 kΩ resistor
between the RBIAS pin and ground. This resister should have
a 1% tolerance and is used to set the master current reference
of the ADC core.
There are three pins that define the serial port interface (SPI) to this
particular ADC. They are the SCLK/DFS, SDIO/DCS, and CSB
pins. The SCLK/DFS (serial clock) is used to synchronize the read
and write data presented to the ADC. The SDIO/DCS (serial data
input/output) is a dual-purpose pin that allows data to be sent and
read from the internal ADC memory map registers. The CSB pin is
an active low control that enables or disables the read and write
cycles (see Table 9).
Rev. 0 | Page 19 of 28
AD9230-11
Table 9. Serial Port Interface Pins
HARDWARE INTERFACE
Mnemonic
SCLK
The pins described in Table 9 comprise the physical interface
between the user’s programming device and the serial port
of the AD9230-11. All serial pins are inputs, which is an opendrain output and should be tied to an external pull-up or
pull-down resistor (suggested value of 10 kΩ).
SDIO
CSB
RESET
Function
SCLK (serial clock) is the serial shift clock in.
SCLK is used to synchronize serial interface
reads and writes.
SDIO (serial data input/output) is a dual-purpose
pin. The typical role for this pin is an input and
output depending on the instruction being sent
and the relative position in the timing frame.
CSB (chip select bar) is an active low control that
gates the read and write cycles.
Master Device Reset. When asserted, device
assumes default settings. Active low.
This interface is flexible enough to be controlled by either PROMS
or PIC microcontrollers as well. This provides the user with an
alternate method to program the ADC other than using an SPI
controller.
If the user chooses not to use the SPI interface, some pins serve
a dual function and are associated with a specific function when
strapped externally to AVDD or ground during device power
on. The Configuration Without the SPI section describes the
strappable functions supported on the AD9230-11.
The falling edge of CSB, in conjunction with the rising edge of
the SCLK, determines the start of the framing. An example of
the serial timing and its definitions can be found in Figure 33
and Table 11.
CONFIGURATION WITHOUT THE SPI
During an instruction phase, a 16-bit instruction is transmitted.
Data then follows the instruction phase and is determined by
the W0 and W1 bits, which is 1 or more bytes of data. All data is
composed of 8-bit words. The first bit of each individual byte of
serial data indicates whether this is a read or write command.
This allows the serial data input/output (SDIO) pin to change
direction from an input to an output.
In applications that do not interface to the SPI control registers,
the SDIO/DCS and SCLK/DFS pins can alternately serve as
standalone CMOS-compatible control pins. When the device is
powered up, it is assumed that the user intends to use the pins
as static control lines for the duty cycle stabilizer. In this mode,
the CSB pin should be connected to AVDD, which disables the
serial port interface.
Data can be sent in MSB or in LSB first mode. MSB first is
default on power-up and can be changed by changing the
configuration register. For more information about this feature
and others, see the AN-877 Application Note, Interfacing to
High Speed ADCs via SPI, at www.analog.com.
Table 10. Mode Selection
Mnemonic
SDIO/DCS
SCLK/DFS
tDS
tS
tHI
External Voltage
AVDD
AGND
AVDD
AGND
Configuration
Duty cycle stabilizer enabled
Duty cycle stabilizer disabled
Twos complement enabled
Offset binary enabled
tCLK
tDH
tH
tLO
CSB
SCLK DON’T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
Figure 33. Serial Port Interface Timing Diagram
Rev. 0 | Page 20 of 28
D4
D3
D2
D1
D0
DON’T CARE
07101-027
SDIO DON’T CARE
DON’T CARE
AD9230-11
Table 11. Serial Timing Definitions
Parameter
tDS
tDH
tCLK
tS
tH
tHI
tLO
tEN_SDIO
Timing (minimum, ns)
5
2
40
5
2
16
16
1
tDIS_SDIO
5
Description
Setup time between the data and the rising edge of SCLK
Hold time between the data and the rising edge of SCLK
Period of the clock
Setup time between CSB and SCLK
Hold time between CSB and SCLK
Minimum period that SCLK should be in a logic high state
Minimum period that SCLK should be in a logic low state
Minimum time for the SDIO pin to switch from an input to an output relative to the SCLK
falling edge (not shown in Figure 33)
Minimum time for the SDIO pin to switch from an output to an input relative to the SCLK
rising edge (not shown in Figure 33)
Table 12. Output Data Format
Input (V)
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
Condition (V)
< 0.62
= 0.62
=0
= 0.62
> 0.62 + 0.5 LSB
Offset Binary Output Mode
D10 to D0
0000 0000 000
0000 0000 000
0000 0000 000
1111 1111 111
1111 1111 111
Rev. 0 | Page 21 of 28
Twos Complement Mode
D10 to D0
1000 0000 000
1000 0000 000
0000 0000 000
0111 1111 111
0111 1111 111
OR
1
0
0
0
1
AD9230-11
MEMORY MAP
READING THE MEMORY MAP TABLE
RESERVED LOCATIONS
Each row in the memory map table has eight address locations.
The memory map is roughly divided into three sections: chip
configuration register map (Address 0x00 to Address 0x02),
transfer register map (Address 0xFF), and ADC functions map
(Address 0x08 to Address 0x2A).
Undefined memory locations should not be written to other
than their default values suggested in this data sheet. Addresses
that have values marked as 0 should be considered reserved and
have a 0 written into their registers during power-up.
The Addr. (Hex) column of the memory map indicates the
register address in hexadecimal, and the Default Value (Hex)
column shows the default hexadecimal value that is already
written into the register. The Bit 7 (MSB) column is the start of
the default hexadecimal value given. For example, Hexadecimal
Address 0x09, the clock register, has a hexadecimal default value
of 0x01. This means Bit 7 = 0, Bit 6 = 0, Bit 5 = 0, Bit 4 = 0, Bit 3 = 0,
Bit 2 = 0, Bit 1 = 0, and Bit 0 = 1, or 0000 0001 in binary. The
default value enables the duty cycle stabilizer. Overwriting this
default so that Bit 0 = 0 disables the duty cycle stabilizer. For more
information on this and other functions, consult the AN-877
Application Note, Interfacing to High Speed ADCs via SPI, at
www.analog.com.
Coming out of reset, critical registers are preloaded with default
values. These values are indicated in Table 13. Other registers
do not have default values and retain the previous value when
exiting reset.
DEFAULT VALUES
LOGIC LEVELS
An explanation of logic level terminology follows: “bit is set” is
synonymous with “bit is set to Logic 1” or “writing Logic 1 for
the bit.” Similarly, “clear a bit” is synonymous with “bit is set to
Logic 0” or “writing Logic 0 for the bit.”
TRANSFER REGISTER MAP
Address 0x08 to Address 0x18 are shadowed. Writes to these
addresses do not affect part operation until a transfer command
is issued by writing 0x01 to Address 0xFF, setting the transfer
bit. This allows these registers to be updated internally and
simultaneously when the transfer bit is set. The internal update
takes place when the transfer bit is set, and the bit autoclears.
Table 13. Memory Map Register
Addr.
Bit 7
(Hex) Register Name
(MSB)
Chip Configuration Registers
0x00
chip_port_config
0
0x01
chip_id
0x02
chip_grade
Transfer Register
0xFF
device_update
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(LSB)
LSB
first
Soft
reset
1
1
Soft
reset
LSB first
0
8-bit chip ID, Bits[7:0]
AD9230-11 = 0x0C
0
0
0
0
0
0
Speed grade:
11 = 200 MSPS
0
0
Rev. 0 | Page 22 of 28
Default
Value
(Hex)
0x18
Readonly
X
X
X
Readonly
0
0
SW
transfer
0x00
Notes/
Comments
The nibbles should
be mirrored by the
user so that LSB-or
MSB-first mode
registers correctly,
regardless of shift
mode.
Default is unique
chip ID, different
for each device.
This is a read-only
register.
Child ID used to
differentiate
graded devices.
Synchronously
transfers data from
the master shift
register to the
slave.
AD9230-11
Addr.
(Hex) Register Name
ADC Functions
0x08
modes
Bit 7
(MSB)
Bit 6
Bit 5
Bit 4
Bit 3
0
0
PWDN:
0 = full
(default)
1=
standby
0
0
0x09
clock
0
0
0
0
0x0D
test_io
0
0
Reset
PN23
gen:
1 = on
0 = off
(default)
Reset
PN9 gen:
1 = on
0 = off
(default)
0x0F
ain_config
0
0
0
0
0x14
output_mode
0
0
0
0x15
output_adjust
0
0
0
Output
enable:
0=
enable
(default)
1=
disable
0
16
output_phase
Output
clock
polarity
1=
inverted
0=
normal
(default)
0
0
0
Bit 2
Bit 1
Bit 0
(LSB)
Internal power-down mode:
000 = normal (power-up, default)
001 = full power-down
010 = standby
011 = normal (power-up)
Note: external PWDN pin
overrides this setting
0
0
0
Duty
cycle
stabilizer:
0=
disabled
1=
enabled
(default)
Output test mode:
0000 = off (default)
0001 = midscale short
0010 = +FS short
0011 = −FS short
0100 = checker board output
0101 = PN 23 sequence
0110 = PN 9
0111 = one/zero word toggle
1000 = unused
1001 = unused
1010 = unused
1011 = unused
1100 = unused
(Format determined by output_mode)
0
CML
0
Analog
enable:
input
disable:
1 = on
0 = off
1 = on
(default)
0 = off
(default)
Data format select:
Output
DDR:
00 = offset binary
invert:
1=
(default)
1 = on
enabled
01 = twos
0 = off
0=
complement
disabled (default)
10 = gray code
(default)
LVDS
course
adjust:
0=
3.5 mA
(default)
1=
2.0 mA
0
Rev. 0 | Page 23 of 28
0
LVDS fine adjust:
001 = 3.50 mA
010 = 3.25 mA
011 = 3.00 mA
100 = 2.75 mA
101 = 2.50 mA
110 = 2.25 mA
111 = 2.00 mA
0
Default
Value
(Hex)
0x00
Notes/
Comments
Determines various
generic modes of
chip operation.
0x01
0x00
0x00
0x00
0x00
0x03
When this register
is set, the test data
is placed on the
output pins in
place of normal
data.
AD9230-11
Addr.
(Hex)
0x17
Register Name
flex_output_delay
0x18
flex_vref
0x2A
ovr_config
Bit 7
(MSB)
Output
delay
enable:
0=
enable
1=
disable
Bit 6
0
Bit 5
0
0
0
0
0
0
0
Bit 4
0
Bit 3
Bit 2
Bit 1
Output clock delay:
00000 = 0.1 ns
00001 = 0.2 ns
00010 = 0.3 ns
…
11101 = 3.0 ns
11110 = 3.1 ns
11111 = 3.2 ns
Input voltage range setting:
10000 = 0.98 V
10001 =1.00 V
10010 = 1.02 V
10011 =1.04 V
…
11111 = 1.23 V
00000 = 1.25 V
00001 = 1.27 V
…
01110 = 1.48 V
01111 = 1.50 V
0
0
OR
position
(DDR
mode
only):
0 = Pin 9,
Pin 10
1=
Pin 21,
Pin 22
Rev. 0 | Page 24 of 28
Bit 0
(LSB)
Default
Value
(Hex)
0
0
OR
enable:
1 = on
(default)
0 = off
0x01
Notes/
Comments
AD9230-11
OUTLINE DIMENSIONS
8.00
BSC SQ
0.60 MAX
14
29
28
15
0.30 MIN
6.50
REF
0.80 MAX
0.65 TYP
0.50 BSC
PIN 1
INDICATOR
4.45
4.30 SQ
4.15
EXPOSED
PAD
(BOTTOM VIEW)
7.75
BSC SQ
0.50
0.40
0.30
SEATING
PLANE
1
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VLLD-2
100808-A
TOP
VIEW
12° MAX
56
43
42
PIN 1
INDICATOR
1.00
0.85
0.80
0.30
0.23
0.18
0.60 MAX
Figure 34. 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
8 mm × 8 mm Body, Very Thin Quad
(CP-56-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9230BCPZ11-200 1
AD923011-200EBZ1
1
Temperature Range
−40°C to +85°C
Package Description
56-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
LVDS Evaluation Board
Z = RoHS Compliant Part.
Rev. 0 | Page 25 of 28
Package Option
CP-56-2
AD9230-11
NOTES
Rev. 0 | Page 26 of 28
AD9230-11
NOTES
Rev. 0 | Page 27 of 28
AD9230-11
NOTES
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07101-0-10/08(0)
Rev. 0 | Page 28 of 28
工商网监
湘ICP备2023018690号
