0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
AD9779PCB

AD9779PCB

  • 厂商:

    AD(亚德诺)

  • 封装:

  • 描述:

    AD9779PCB - Dual 16-Bit, 1.0 GSPS D/A Converter - Analog Devices

  • 数据手册
  • 价格&库存
AD9779PCB 数据手册
Dual 16-Bit, 1.0 GSPS D/A Converter Preliminary Technical Data FEATURES • 1.8/3.3 V Single Supply Operation • Low power: 950mW (IOUTFS = 20 mA; fDAC = 1 GSPS, 4× Interpolation • DNL = ± 1.5 LSB, INL = ± 5.0 LSB • SFDR =82 dBc to fOUT = 100 MHz • ACLR = 87 dBc @ 80 MHz IF • CMOS data interface with Autotracking Input Timing • Analog Output: Adjustable 10-30mA (RL=25 Ω to 50 Ω) • 100-lead Exposed Paddle TQFP Package • Multiple Chip Synchronization Interface • 84dB Digital Interpolation Filter Stopband Attenuation • Digital Inverse Sinc Filter AD9779 DAC that provides a sample rate of 1 GSPS, permitting multi carrier generation up to its Nyquist frequency. It includes features optimized for direct conversion transmit applications, including complex digital modulation and gain and offset compensation. The DAC outputs are optimized to interface seamlessly with analog quadrature modulators such as the AD8349. A serial peripheral interface (SPI) provides for programming many internal parameters and also enables read-back of status registers. The output current can be programmed over a range of 10mA to 30mA. The AD9779 is manufactured on an advanced 0.18µm CMOS process and operates from 1.8V and 3.3V supplies for a total power consumption of 950mW. It is supplied in a 100-lead QFP package. PRODUCT HIGHLIGHTS Ultra-low noise and Intermodulation Distortion (IMD) enable high quality synthesis of wideband signals from baseband to high intermediate frequencies. Single-ended CMOS interface supports a maximum input rate of 300 MSPS with 1x interpolation. Manufactured on a CMOS process, the AD9779 uses a proprietary switching technique that enhances dynamic performance. The current outputs of the AD9779 can be easily configured for various single-ended or differential circuit topologies. APPLICATIONS • Wireless Infrastructure Direct Conversion Transmit Diversity • Wideband Communications Systems: Point-to-Point Wireless, LMDS PRODUCT DESCRIPTION The AD9779 is a dual 16-bit high performance, high frequency FUNCTIONAL BLOCK DIAGRAM SYNC_O SYNC_I DATACLK_OUT Delay Line Clock Generation/Distribution Delay Line Clock Multiplier 2X/4X/8X CLK+ CLK- Data Assembler P1D[15:0] I Latch 2X 2X 2X n * Fdac/8 n = 1, 2, 3… 7 Q Latch P2D[15:0] 2X 2X 2X Complex Modulator Sinc-1 IOUT1_P 16-Bit IDAC IOUT1_N IOUT2_P 16-Bit QDAC IOUT2_N Sinc-1 Digital Controller 10 10 Gain Gain Reference & Bias VREF RSET AUX1_P AUX1_N AUX2_P AUX2_N Serial Peripheral Interface Power-On Reset 10 10 Offset Offset SDO SDIO Rev. PrD Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. SCLK CSB Figure 1 Functional Block Diagram One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 © 2005 Analog Devices, Inc. All rights reserved. AD9779 TABLE OF CONTENTS Specifications............................................................................................3 DC SPECIFICATIONS ......................................................................3 DIGITAL SPECIFICATIONS............................................................4 AC SPECIFICATIONS.......................................................................4 Pin Function Descriptions .....................................................................5 Pin Configuration....................................................................................6 Interpolation Filter Coefficients............................................................7 INTERPOLATION Filter RESPONSE CURVES................................8 CHARACTERIZATION DATA ............................................................9 General Description ..............................................................................12 Serial Peripheral Interface................................................................12 General Operation of the Serial Interface......................................12 Preliminary Technical Data Instruction Byte .................................................................................12 Serial Interface Port Pin Descriptions ............................................12 MSB/LSB Transfers ...........................................................................13 Notes on Serial Port Operation .......................................................13 SPI Register Map ...............................................................................14 Internal Reference/Full Scale Current Generation.......................22 Auxiliary DACs..................................................................................22 Power Down and Sleep Modes........................................................22 Internal PLL Clock Multiplier / Clock Distribution.....................23 Timing Information ..........................................................................23 Interpolation Filter Architecture.....................................................25 EvaLuation Board Schematics..............................................................27 REVISION HISTORY Revision PrA: Initial Version Revision PrB: Updated Page 1 Features, added eval board schematics, SPI register map, filter coefficients and filter response curves Revision PrC: Added characterization data, description of modulation modes, internal clock distribution architecture, timing information Revision PrD: Added more ac characterization data, power dissipation Rev. PrD | Page 2 of 34 Preliminary Technical Data SPECIFICATIONS1 DC SPECIFICATIONS (VDD33 = 3.3 V, VDD18 = 1.8 V, MAXIMUM SAMPLE RATE, UNLESS OTHERWISE NOTED) Parameter RESOLUTION ACCURACY Integral Nonlinearity (DNL) Differential Nonlinearity (INL) Offset Error Gain Error (With Internal Reference) Gain Error (Without Internal Reference) ANALOG OUTPUTS Full Scale Output Current Output Compliance Range Output Resistance Output Capacitance Offset TEMPERATURE DRIFT Gain Reference Voltage REFERENCE ANALOG SUPPLY VOLTAGES DIGITAL SUPPLY VOLTAGES POWER CONSUMPTION Internal Reference Voltage Output Current VDDA33 VDDA18 VDDD33 VDDD18 VDDCLK 600 MSPS Standby Power Table 1: DC Specifications AD9779 Temp Test Level Min Typ 16 ± 1.5 ±5 ± TBD ± TBD ± TBD 20 TBD TBD TBD TBD TBD 1.2 100 3.3 1.8 3.3 1.8 1.8 TBD TBD Max Unit Bits LSB LSB % FSR % FSR % FSR 10 1.0 30 mA V kΩ pF ppm/°C ppm/°C ppm/°C V nA V V V V V mW mW 3.13 1.70 3.13 1.70 1.70 3.47 1.90 3.47 1.90 1.90 1 Specifications subject to change without notice Rev. PrD | Page 3 of 34 AD9779 DIGITAL SPECIFICATIONS Preliminary Technical Data (VDD33 = 3.3 V, VDD18 = 1.8 V, MAXIMUM SAMPLE RATE, UNLESS OTHERWISE NOTED) Parameter DAC CLOCK INPUT (CLK+, CLK-) SERIAL PERIPHERAL INTERFACE Differential peak-to-peak Voltage Common Mode Voltage Maximum Clock Rate Maximum Clock Rate (SCLK) Maximum Pulse width high Maximum pulse width low Table 2: Digital Specifications Temp Test Level Min Typ 800 400 1 Max Unit mV mV GSPS MHz ns ns 40 TBD TBD AC SPECIFICATIONS (VDD33 = 3.3 V, VDD18 = 1.8 V, MAXIMUM SAMPLE RATE, UNLESS OTHERWISE NOTED) Parameter DYNAMIC PERFORMANCE Output Settling Time (tst) (to 0.025%) Output Rise Time (10% to 90%) Output Fall Time (90% to 10%) Output Noise (IoutFS=20mA) fDAC = 100 MSPS, fOUT = 20 MHz fDAC = 200 MSPS, fOUT = 50 MHz fDAC = 400 MSPS, fOUT = 70 MHz fDAC = 800 MSPS, fOUT = 70 MHz fDAC = 200 MSPS, fOUT = 50 MHz fDAC = 400 MSPS, fOUT = 60 MHz fDAC = 400 MSPS, fOUT = 80 MHz fDAC = 800 MSPS, fOUT = 100 MHz fDAC = 156 MSPS, fOUT = 60 MHz fDAC = 200 MSPS, fOUT = 80 MHz fDAC = 312 MSPS, fOUT = 100 MHz fDAC = 400 MSPS, fOUT = 100 MHz fDAC = 245.76 MSPS, fOUT = 20 MHz fDAC = 491.52 MSPS, fOUT = 100 MHz fDAC = 491.52 MSPS, fOUT = 200 MHz fDAC = 245.76 MSPS, fOUT = 60 MHz fDAC = 491.52 MSPS, fOUT = 100 MHz fDAC = 491.52 MSPS, fOUT = 200 MHz Table 3: AC Specifications Temp Test Level Min Typ TBD TBD TBD TBD 82 82 84 87 91 88 81 88 -158 -157 -159 -159 80 79 74 78 80 76 Max Unit ns ns ns pA/rtHz dBc dBc dBc dBc dBc dBc dBc dBc dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBc dBc dBc dBc dBc dBc SPURIOUS FREE DYNAMIC RANGE (SFDR) TWO-TONE INTERMODULATION DISTORTION (IMD) NOISE SPECTRAL DENSITY (NSD) WCDMA ADJACENT CHANNEL LEAKAGE RATIO (ACLR), SINGLE CARRIER WCDMA SECOND ADJACENT CHANNEL LEAKAGE RATIO (ACLR), SINGLE CARRIER Rev. PrD | Page 4 of 34 Preliminary Technical Data PIN FUNCTION DESCRIPTIONS Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 AD9779 Pin No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Name VDDC18 VDDC18 VSSC VSSC CLK+ CLKVSSC VSSC VDDC18 VDDC18 VSSC VSSC SYNC_I+ SYNC_IVSSD VDDD33 P1D P1D P1D P1D P1D VSSD VDDD18 P1D P1D P1D P1D P1D P1D P1D P1D VSSD VDDD18 P1D P1D P1D DATACLK_OUT VDDD33 TXENABLE P2D P2D P2D VDDD18 VSSD P2D P2D P2D P2D P2D P2D Description 1.8 V Clock Supply 1.8 V Clock Supply Clock Common Clock Common Differential Clock Input Differential Clock Input Clock Common Clock Common 1.8 V Clock Supply 1.8 V Clock Supply Clock Common Clock Common Differential Synchronization Input Differential Synchronization Input Digital Common 3.3 V Digital Supply Port 1 Data Input D15 (MSB) Port 1 Data Input D14 Port 1 Data Input D13 Port 1 Data Input D12 Port 1 Data Input D11 Digital Common 1.8 V Digital Supply Port 1 Data Input D10 Port 1 Data Input D9 Port 1 Data Input D8 Port 1 Data Input D7 Port 1 Data Input D6 Port 1 Data Input D5 Port 1 Data Input D4 Port 1 Data Input D3 Digital Common 1.8 V Digital Supply Port 1 Data Input D2 Port 1 Data Input D1 Port 1 Data Input D0 (LSB) Data Clock Output 3.3 V Digital Supply Transmit Enable Port 2 Data Input D15 (MSB) Port 2 Data Input D14 Port 2 Data Input D13 1.8 V Digital Supply Digital Common Port 2 Data Input D12 Port 2 Data Input D11 Port 2 Data Input D10 Port 2 Data Input D9 Port 2 Data Input D8 Port 2 Data Input D7 Name P2D P2D VDDD18 VSSD P1D P1D P1D P1D P1D VDDD18 VDDD33 SYNC_OSYNC_O+ VSSD PLL_LOCK SPI_SDO SPI_SDIO SPI_CLK SPI_CSB RESET IRQ VSS IPTAT VREF I120 VDDA33 VSSA VDDA33 VSSA VDDA33 VSSA VSSA IOUT2_P IOUT2_N VSSA AUX2_P AUX2_N VSSA AUX1_N AUX1_P VSSA IOUT1_N IOUT1_P VSSA VSSA VDDA33 VSSA VDDA33 VSSA VDDA33 Description Port 2 Data Input D6 Port 2 Data Input D5 1.8 V Digital Supply Digital Common Port 2 Data Input D4 Port 2 Data Input D3 Port 2 Data Input D2 Port 2 Data Input D1 Port 2 Data Input D0 (LSB) 1.8 V Digital Supply 3.3 V Digital Supply Differential Synchronization Output Differential Synchronization Output Digital Common PLL Lock Indicator SPI Port Data Output SPI Port Data Input/Output SPI Port Clock SPI Port Chip Select Bar Reset Interrupt Request Analog Common Reference Current Voltage Reference Output 120 µA Reference Current 3.3 V Analog Supply Analog Common 3.3 V Analog Supply Analog Common 3.3 V Analog Supply Analog Common Analog Common Differential DAC Current Output, Channel 2 Differential DAC Current Output, Channel 2 Analog Common Auxiliary DAC Voltage Output, Channel 2 Auxiliary DAC Voltage Output, Channel 2 Analog Common Auxiliary DAC Voltage Output, Channel 1 Auxiliary DAC Voltage Output, Channel 1 Analog Common Differential DAC Current Output, Channel 1 Differential DAC Current Output, Channel 1 Analog Common Analog Common 3.3 V Analog Supply Analog Common 3.3 V Analog Supply Analog Common 3.3 V Analog Supply Table 4: Pin Function Descriptions Rev. PrD | Page 5 of 34 AD9779 PIN CONFIGURATION IOUT1_N IOUT2_N IOUT1_P IOUT2_P AUX1_N AUX2_N VDDA33 VDDA33 VDDA33 Preliminary Technical Data VDDA33 VDDA33 100 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 VDDC18 VDDC18 VSSC VSSC CLK+ CLKVSSC VSSC VDDC18 VDDC18 VSSC VSSC SYNC_I+ SYNC_IVSSD VDDD33 P1D P1D P1D P1D P1D VSSD VDDD18 P1D P1D 99 76 VDDA33 AUX1_P AUX2_P VSSA VSSA VSSA VSSA VSSA VSSA VSSA VSSA VSSA VSSA VSSA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 75 74 I120 VREF IPTAT VSS IRQ RESET SPI_CSB SPI_CLK SPI_SDI SPI_SDO Analog Domain 73 72 71 70 Digital Domain 69 68 67 66 65 PLL_LOCK 64 VSSD SYNC_O+ SYNC_OVDDD33 VDDD18 P2D P2D P2D P2D P2D VSSD VDDD18 P2D P2D AD9779 63 62 61 60 59 58 57 56 55 54 53 52 51 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 TXEnable P2D P2D P2D P2D P2D P2D VDDD18 VDDD33 VDDD18 P1D P1D P1D P1D P1D P1D P1D P1D P1D P2D P2D Figure 2. Pin Configuration Rev. PrD | Page 6 of 34 P2D VSSD VSSD DCLK 50 Preliminary Technical Data INTERPOLATION FILTER COEFFICIENTS Table 5: Halfband Filter 1 Lower Upper Coefficient Coefficient H(1) H(55) H(2) H(54) H(3) H(53) H(4) H(52) H(5) H(51) H(6) H(50) H(7) H(49) H(8) H(48) H(9) H(47) H(10) H(46) H(11) H(45) H(12) H(44) H(13) H(43) H(14) H(42) H(15) H(41) H(16) H(40) H(17) H(39) H(18) H(38) H(19) H(37) H(20) H(36) H(21) H(35) H(22) H(34) H(23) H(33) H(24) H(32) H(25) H(31) H(26) H(30) H(27) H(29) H(28) Table 6: Halfband Filter 2 Lower Upper Coefficient Coefficient H(1) H(23) H(2) H(22) H(3) H(21) H(4) H(20) H(5) H(19) H(6) H(18) H(7) H(17) H(8) H(16) H(9) H(15) H(10) H(14) H(11) H(13) H(12) Table 7: Halfband Filter 3 Lower Upper Coefficient Coefficient H(1) H(15) H(2) H(14) H(3) H(13) H(4) H(12) H(5) H(11) H(6) H(10) H(7) H(9) H(8) Table 8: Inverse Sinc Filter Lower Upper Coefficient Coefficient H(1) H(9) H(2) H(8) H(3) H(7) H(4) H(6) H(5) AD9779 Integer Value -4 0 13 0 -34 0 72 0 -138 0 245 0 -408 0 650 0 -1003 0 1521 0 -2315 0 3671 0 -6642 0 20755 32768 Integer Value -39 0 273 0 -1102 0 4964 8192 Integer Value 2 -4 10 -35 401 Integer Value -2 0 17 0 -75 0 238 0 -660 0 2530 4096 Rev. PrD | Page 7 of 34 AD9779 INTERPOLATION FILTER RESPONSE CURVES 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -4 -3 -2 -1 0 1 2 3 4 Preliminary Technical Data Figure 3. AD9779 2x Interpolation, Low Pass Response to ±4x Input Data Rate (Dotted Lines Indicate 1dBRoll-Off) 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -4 -3 -2 -1 0 1 2 3 4 Figure 4. AD9779 4x Interpolation, Low Pass Response to ±4x Input Data Rate (Dotted Lines Indicate 1dBRoll-Off) 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -4 -3 -2 -1 0 1 2 3 4 Figure 5.AD9779 8x Interpolation, Low Pass Response to ±4x Input Data Rate (Dotted Lines Indicate 1dBRoll-Off) Rev. PrD | Page 8 of 34 Preliminary Technical Data CHARACTERIZATION DATA AD9779 6 5 100 95 4 90 3 SFDR - dBm 2 INL (LSBs) 1 0 -1 -2 -3 -4 -5 0 8192 16384 24576 32768 Code 40960 49152 57344 65536 85 80 75 70 65 60 55 50 0 20 40 60 80 100 Fout - MHz F D ATA =100MSPS F D ATA =160MSPS F D ATA =200MSPS Figure 6. AD9779 Typical INL Figure 9. SFDR vs. FOUT, 2x Interpolation 2 100 1.5 F D ATA =125MSPS F D ATA =100MSPS 95 90 1 DNL (LSBs) 85 SFDR - dBm 80 75 70 65 F D ATA =150MSPS F D ATA =200MSPS 0.5 0 -0.5 60 55 -1 0 8192 16384 24576 32768 Code 40960 49152 57344 65536 50 0 20 40 Fout - MHz 60 80 Figure 7. AD9779 Typical DNL 100 F D ATA =100MSPS F D ATA =160MSPS F D ATA =200MSPS Figure 10. SFDR vs. FOUT, 4x Interpolation 100 F D ATA =62.5MSPS 50MSPS 90 SFDR - dBm 80 90 SFDR - dBm 80 70 60 50 0 20 40 Fout - M Hz 60 80 100 70 75MSPS 100MSPS 60 50 0 10 20 30 40 50 Fout - M Hz Figure 8. SFDR vs. FOUT, 1x Interpolation Figure 11. SFDR vs. FOUT, 8x Interpolation Rev. PrD | Page 9 of 34 AD9779 100.0 F D ATA =200MSPS 90.0 Preliminary Technical Data 100 90 100MSPS IMD - dBc IMD - dBc 80.0 F D ATA =160MSPS 70.0 80 70 60 75MSPS 112.5MSPS 50MSPS F D ATA =62.5MSPS 60.0 50 0 50.0 0 20 40 Fout - MHz 60 80 50 100 150 200 250 300 350 400 450 Fout - MHz Figure 15. Third Order IMD vs. FOUT, 8x Interpolation Figure 12. Third Order IMD vs. FOUT, 1x Interpolation 100.0 F D ATA =200MSPS 90.0 -150 -152 -154 NSD - dBm/Hz -156 -158 -160 -162 -164 -166 F D ATA =200MSPS F D ATA =78MSPS F D ATA =156MSPS IMD - dBc 80.0 F D ATA =160MSPS 70.0 60.0 -168 - 170 0 10 20 30 40 50 60 70 80 90 50.0 0 20 40 60 80 100 120 140 160 180 200 Fout - MHz Fout - M Hz Figure 16. Noise Spectral Density vs. FOUT, 1x Interpolation Figure 13. Third Order IMD vs. FOUT, 2x Interpolation 100 F D ATA =125MSPS -150 -152 F D ATA =150MSPS F D ATA =156MSPS F D ATA =78MSPS 90 -154 -156 NSD - dBm /Hz -158 -160 -162 -164 -166 IMD - dBc 80 70 60 50 0 40 80 120 160 200 F D ATA =200MSPS F D ATA =100MSPS 240 280 320 360 400 -168 -170 F D ATA =200MSPS Fout - MHz Figure 14. Third Order IMD vs. FOUT, 4x Interpolation 0 20 40 60 80 100 120 140 160 180 Fout - MHz Figure 17. Noise Spectral Density vs. FOUT, 2x Interpolation Rev. PrD | Page 10 of 34 Preliminary Technical Data 0.7 AD9779 8x Interpolation -90 -85 -80 ACLR - dBc -75 -70 Power - W 0.5 8x Interpolation, Zero Stuffing F D ATA =122.88MSPS 0.6 4x Interpolation 4x Interpolation, Zero Stuffing 2x Interpolation, Zero Stuffing -65 -60 -55 -50 0 F D ATA =61.44MSPS 0.4 2x Interpolation 1x Interpolation, Zero Stuffing 1x Interpolation 0.3 20 40 60 80 100 120 140 160 180 200 220 Fout - M Hz 240 260 280 300 0.2 0.1 Figure 18. ACLR for 1st Adjacent Band WCDMA, 4x Interpolation. On-Chip Modulation is used to translate baseband signal to IF. -90 -85 -80 ACLR - dBc -75 -70 -65 -60 -55 -50 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Fout - MHz F D ATA =61.44MSPS F D ATA =122.88MSPS 0 0 25 50 75 100 125 F DAT A ( MSPS) 150 175 200 225 250 Figure 21. Power Dissipation, Single DAC Mode 1.1 8x Interpolation,F DA C/4 Modulation 1 0.9 0.8 0.7 Power - W 0.6 0.5 0.4 0.3 0.2 8x Interpolation, Zero Stuffing 4x Interpolation, Zero Stuffing 8x Interpolation,F DA C/2 Modulation 8x Interpolation,F DA C/8 Modulation 8x Interpolation,Modulation off 4x Interpolation,F DA C/4 Modulation 4x Interpolation,F DA C/2 Modulation 4x Interpolation,Modulation off 2x Interpolation, Zero Stuffing 2x Interpolation,F DA C/2 Modulation 2x Interpolation,Modulation off 1x Interpolation, Zero Stuffing Figure 19. ACLR for 2nd Adjacent Band WCDMA, 4x Interpolation. On-Chip Modulation is used to translate baseband signal to IF. -90 -85 F D ATA =122.88MSPS 1x Interpolation 0.1 0 0 25 50 75 100 125 150 175 200 225 250 F DATA ( M SPS) -80 ACLR - dBc -75 -70 -65 -60 -55 -50 Power - W F D ATA =61.44MSPS Figure 22. Power Dissipation, Dual DAC Mode 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 0 200 400 600 FDAC - M SPS 800 1000 1200 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Fout - M Hz Figure 20. ACLR for 3rd Adjacent Band WCDMA, 4x Interpolation. On-Chip Modulation is used to translate baseband signal to IF. Figure 23. Power Dissipation of Inverse Sinc Filter Rev. PrD | Page 11 of 34 AD9779 GENERAL DESCRIPTION The AD9779 combines many features which make it make it a very attractive DAC for wired and wireless communications systems. The dual digital signal path and dual DAC structure allow an easy interface with common quadrature modulators when designing single sideband transmitters. The speed and performance of the AD9779 allow wider bandwidths/more carriers to be synthesized than with previously available DACs. The digital engine in the AD9779 uses a breakthrough filter architecture that combines the interpolation with a digital quadrature modulator. This allows the AD9779 to do digital quadrature frequency up conversion. The AD9779 also has features which allow simplified synchronization with incoming data, and also allows multiple AD9779s to be synchronized. Preliminary Technical Data The remaining SCLK edges are for Phase 2 of the communication cycle. Phase 2 is the actual data transfer between the AD9779 and the system controller. Phase 2 of the communication cycle is a transfer of 1, 2, 3, or 4 data bytes as determined by the instruction byte. Using one multibyte transfer is the preferred method. Single byte data transfers are useful to reduce CPU overhead when register access requires one byte only. Registers change immediately upon writing to the last bit of each transfer byte. Instruction Byte The instruction byte contains the information shown in Error! Reference source not found.. MSB I7 R/W I6 N1 I5 N0 I4 A4 I3 A3 I2 A2 I1 A1 LSB I0 A0 Serial Peripheral Interface SPI_SDO (pin 66) SPI_SDI (pin 67) SPI_SCLK (pin 68) SPI_CSB (pin 69) AD9779 SPI PORT Table 9. SPI Instruction Byte Figure 24. AD9779 SPI Port The AD9779 serial port is a flexible, synchronous serial communications port allowing easy interface to many industrystandard microcontrollers and microprocessors. The serial I/O is compatible with most synchronous transfer formats, including both the Motorola SPI® and Intel® SSR protocols. The interface allows read/write access to all registers that configure the AD9779. Single or multiple byte transfers are supported, as well as MSB first or LSB first transfer formats. The AD9779’s serial interface port can be configured as a single pin I/O (SDIO) or two unidirectional pins for in/out (SDIO/SDO). R/W, Bit 7 of the instruction byte, determines whether a read or a write data transfer will occur after the instruction byte write. Logic high indicates read operation. Logic 0 indicates a write operation. N1, N0, Bits 6 and 5 of the instruction byte, determine the number of bytes to be transferred during the data transfer cycle. The bit decodes are shown in Table 10. A4, A3, A2, A1, A0, Bits 4, 3, 2, 1, 0 of the instruction byte, determine which register is accessed during the data transfer portion of the communications cycle. For multibyte transfers, this address is the starting byte address. The remaining register addresses are generated by the AD9779 based on the LSBFIRST bit (REG00, bit 6). N1 0 0 1 1 N2 0 1 0 1 Description Transfer 1 Byte Transfer 2 Bytes Transfer 3 Bytes Transfer 4 Bytes General Operation of the Serial Interface There are two phases to a communication cycle with the AD9779. Phase 1 is the instruction cycle, which is the writing of an instruction byte into the AD9779, coincident with the first eight SCLK rising edges. The instruction byte provides the AD9779 serial port controller with information regarding the data transfer cycle, which is Phase 2 of the communication cycle. The Phase 1 instruction byte defines whether the upcoming data transfer is read or write, the number of bytes in the data transfer, and the starting register address for the first byte of the data transfer. The first eight SCLK rising edges of each communication cycle are used to write the instruction byte into the AD9779. A logic high on the CS pin, followed by a logic low, will reset the SPI port timing to the initial state of the instruction cycle. This is true regardless of the present state of the internal registers or the other signal levels present at the inputs to the SPI port. If the SPI port is in the midst of an instruction cycle or a data transfer cycle,none of the present data will be written. Table 10. Byte Transfer Count Serial Interface Port Pin Descriptions SCLK—Serial Clock. The serial clock pin is used to synchronize data to and from the AD9779 and to run the internal state machines. SCLK’s maximum frequency is 20 MHz. All data input to the AD9779 is registered on the rising edge of SCLK. All data is driven out of the AD9779 on the falling edge of SCLK. CSB—Chip Select. Active low input starts and gates a communication cycle. It allows more than one device to be used on the same serial communications lines. The SDO and SDIO pins will go to a high impedance state when this input is high. Chip select should stay low during the entire communication cycle. SDIO—Serial Data I/O. Data is always written into the AD9779 on Rev. PrD | Page 12 of 34 Preliminary Technical Data this pin. However, this pin can be used as a bidirectional data line. The configuration of this pin is controlled by Bit 7 of register address 00h. The default is Logic 0, which configures the SDIO pin as unidirectional. SDO—Serial Data Out. Data is read from this pin for protocols that use separate lines for transmitting and receiving data. In the case where the AD9779 operates in a single bidirectional I/O mode, this pin does not output data and is set to a high impedance state. INSTRUCTION CYCLE CSB AD9779 DATA TRANSFER CYCLE SCLK SDIO R/W N0 N1 A0 A1 A2 A3 A4 D7 D6N D5N D30 D20 D10 D00 03152-0-004 03152-PrD-007 03152-PrD-006 SDO D7 D6N D5N D30 D20 D10 D00 MSB/LSB Transfers Figure 25. Serial Register Interface Timing MSB First The AD9779 serial port can support both most significant bit (MSB) first or least significant bit (LSB) first data formats. This functionality is controlled by register bit LSBFIRST (REG00, bit 6). The default is MSB first (LSBFIRST = 0). When LSBFIRST = 0 (MSB first) the instruction and data bytes must be written from most significant bit to least significant bit. Multibyte data transfers in MSB first format start with an instruction byte that includes the register address of the most significant data byte. Subsequent data bytes should follow in order from high address to low address. In MSB first mode, the serial port internal byte address generator decrements for each data byte of the multibyte communication cycle. When LSBFIRST = 1 (LSB first) the instruction and data bytes must be written from least significant bit to most significant bit. Multibyte data transfers in LSB first format start with an instruction byte that includes the register address of the least significant data byte followed by multiple data bytes. The serial port internal byte address generator increments for each byte of the multibyte communication cycle. The AD9779 serial port controller data address will decrement from the data address written toward 0x00 for multibyte I/O operations if the MSB first mode is active. The serial port controller address will increment from the data address written toward 0x1F for multibyte I/O operations if the LSB first mode is active. INSTRUCTION CYCLE CSB DATA TRANSFER CYCLE SCLK SDIO A0 A1 A2 A3 A4 N1 N0 R/W D00 D10 D20 D4N D5N D6N D7N 03152-0-005 SDO D00 D10 D20 D4N D5N D6N D7N Figure 26. Serial Register Interface Timing LSB First tDS CSB tSCLK tPWH SCLK tPWL tDS SDIO tDH INSTRUCTION BIT 6 INSTRUCTION BIT 7 Figure 27. Timing Diagram for SPI Register Write CSB SCLK tDV SDIO SDO DATA BIT n DATA BIT n –1 Notes on Serial Port Operation The AD9779 serial port configuration is controlled by REG00, bits 6 and 7 . It is important to note that the configuration changes immediately upon writing to the last bit of the register. For multibyte transfers, writing to this register may occur during the middle of communication cycle. Care must be taken to compensate for this new configuration for the remaining bytes of the current communication cycle. The same considerations apply to setting the software reset, RESET (REG00, bit 5). All registers are set to their default values EXCEPT REG00 and REG04 which remain unchanged. Use of only single byte transfers when changing serial port configurations or initiating a software reset is recommended to prevent unexpected device behavior. Rev. PrD | Page 13 of 34 Figure 28. Timing Diagram for SPI Register Read AD9779 SPI Register Map Register Name Comm Register Address Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Preliminary Technical Data Bit 2 Bit 1 Bit 0 Default 00h 00 SDIO Bidirectional LSB,MSB First Software Reset Power Down Mode Auto Power Down Enable PLL Lock Indicator 00h Digital Control Register 01h 01 Filter Interpolation Factor Filter Interpolation Mode Zero Stuffing Enable DATACLK Invert IQ Select Invert Q First 00h 02h 02 Data Format One Port Mode Real Mode Inverse Sinc Enable 00h Sync Control 03h 04h 05h 03 04 05 Data Delay Mode Sync Out Delay Sync Enable Sync Driver Enable Sync Delay IRQ Data Clock Delay Data Window Delay Sync Window Delay 00h 00h 00h Dac Clock Offset Interrupt Register 06h 06 Data Delay IRQ Cross Control IRQ Data Delay IRQ Enable Sync Delay IRQ Enable Cross Control IRQ Enable 00h PLL Control 07h 08h 07 08 PLL Band Select PLL Enable PLL Output Freq Divide PLL Loop Freq Divide PLL Loop Cap Select PLL Loop Filter Pole/Zero CFh 37h Misc. Control Register I DAC Control Register 09h 24 PLL Error Source PLL Ref Bypass PLL Gain PLL Bias 38h 0Ah 0Bh 09 10 IDAC Gain Adjustment IDAC SLEEP IDAC Power Down IDAC Gain Adjustment F9h 01h Aux 1 DAC Control Register 0Ch 11 Auxiliary DAC1 Data 00h 0Dh 12 Auxiliary DAC1 Sign Auxiliary DAC1 Current Direction Auxiliary DAC1 Sleep Auxiliary DAC1 Data 00h Q DAC Control Register 0Eh 13 QDAC Gain Adjustment F9h 0Fh 14 QDAC SLEEP QDAC Sleep QDAC Gain Adjustment 01h Rev. PrD | Page 14 of 34 Preliminary Technical Data Aux 2 DAC Control Register 10h 15 Auxiliary DAC2 Data AD9779 00h 11h 16 Auxiliary DAC2 Sign Auxiliary DAC2 Current Direction Auxiliary DAC2 Power Down Auxiliary DAC2 Data 00h 12h 17 18 19 20 23 Cross Updel Cross Dndel Cross Clock Divide Cross Run Cross Status Cross Done Cross Wiggle Delay Cross Wiggle Cross Step 00h 00h 00h 00h 00h Cross Register 13h 14h 15h Analog Write Analog Control Register Analog Status Register Test 1 Register 16h Analog Write 17h 18h 19h 21 22 25 Mirror Roll Off Stack Headroom Control Analog Status Band Gap Trim 00h CAh --h 1Ah 26 MISR Enable MISR IQ Select MISR Samples Internal Data Enable Test Mode 00h Test 2 Register 1Bh 1Ch 1Dh 1Eh 27 28 29 30 BIST BIST BIST BIST --h --h --h --h Table 11: SPI Register Map Rev. PrD | Page 15 of 34 AD9779 Register (hex) 00 Comm Register Bits 7 6 5 4 3 1 01 Digital Path Filter Control 7:6 Name SDIO Bidirectional LSB/MSB First Software RESET Power Down Mode Auto Power Down Enable PLL LOCK (read only) Filter Interpolation Rate Preliminary Technical Data Function 0: Use SDIO pin as input data only 1: Use SDIO as both input and output data 0: First bit of serial data is MSB of data byte 1: First bit of serial data is LSB of data byte Bit must be written with a 1, then 0 to soft reset SPI register map 0: All circuitry is active 1: Disable all digital and analog circuitry, only SPI port is active Default 0 0 0 0 0 0: PLL is not locked 1: PLL is locked 00: 1x interpolation 01: 2x interpolation 10: 4x interpolation 11: 8x interpolation See Table 13 for filter modes 0: Zero stuffing off 1: Zero stuffing on 0: Signed binary 1: Unsigned binary 0: Both input data ports receive data 1: Data port 1 only receives data 0: Enable Q path for signal processing 1: Disable Q path data (clocks disabled) 0: Inverse sinc disabled 1: Inverse sinc disabled 0: Output DATACLK same phase as internal capture clock 1: Output DATACLK opposite phase as internal capture clock 0: TxEnable (pin 39) =1, routes input data to I channel TxEnable (pin 39) =0, routes input data to Q channel 1: TxEnable (pin 39) =1, routes input data to Q channel TxEnable (pin 39) =0, routes input data to I channel 0: First byte of data is always I data at beginning of transmit 1: First byte of data is always Q data at beginning of transmit 00: Manual, no error correction 01: Manual, continuous error correction 10: automatic, one pass check 11: automatic, continuous pass check Data Clock delay control Window delay control 0 00 5:2 0 02 General Mode Control 7 6 5 3 2 1 Control Halfband Filters 1,2,3 Zero Stuffing Data Format One Port Mode Real Mode Inverse Sinc Enable DATACLK Invert IQ Select Invert 0000 0 0 0 0 0 0 0 0 03 Data Clock Delay 7:6 Q First Data Delay Mode 00 5:3 2:0 04 Synchronization Delay 05 Chip Sync and Data Delay Control 7:4 3:0 7 6 5:3 Data Clock Delay Data Window Delay Sync Output Delay Sync Window Delay Sync Enable Sync Driver Enable DAC Clock Offset 000 000 0000 0000 0: LVDS and synchronization rceiver logic off 1: LVDS and synchronization rceiver logic on 0: LVDS driver off 1: LVDS driver on 0 0 0 Rev. PrD | Page 16 of 34 Preliminary Technical Data 06 IRQ Status 7 6 Data Delay Error (read only) Chip Synchronization Delay Error (read only) Cross Control Error (read only) Data Delay Error Enable Chip Synchronization Error Enable Cross Control Error Enable PLL Band Select See Table 14 for values. PLL Ripple Cap Adjust PLL Enable 0 0 AD9779 5 3 2 0 0 0 1 07 PLL Band and Divide 7:3 0 11001 2:0 08 PLL Enable and Charge Pump Control 7 111 0: PLL off, DAC rate clock supplied by outside source 1: PLL on, DAC rate clock synthesized internally from data rate clock via PLL clock multiplier 00: Divide by 1 01: Divide by 2 10: Divide by 4 11: Divide by 8 00: Divide by 1 01: Divide by 2 10: Divide by 4 11: Divide by 8 000: PLL band select 00000-00111 100: PLL band select 01000-01111 110: PLL band select 10000-10111 111: PLL band select 11000-11111 0 6:5 PLL Output Divide Ratio 01 4:3 PLL Loop Feedback Divide Ratio PLL Loop Filter Bandwidth Tuning Recommended Settings. See Table 14 for PLL Band Select values. PLL Error Bit Source PLL Reference Bypass VCO AGC Gain Control. See Table 14 for PLL Band Select values. PLL Bias Current Level/Trim IDAC Gain Adjustment IDAC Sleep IDAC Power Down IDAC Gain Adjustment Aux DAC1 Gain Adjustment 10 2:0 111 09 Misc. Control 7 6 5:3 0: Phase error detect 1: Range limit 0: Use PLL reference 1: Use DAC reference 000: PLL band select 00000-00111 100: PLL band select 01000-01111 110: PLL band select 10000-10111 111: PLL band select 11000-11111 0 0 111 2:0 0A IDAC Gain 0B IDAC Gain and Control 7:0 7 6 1:0 0C Auxiliary DAC1 Gain 7:0 000 (7:0) LSB slice of 10 bit gain setting word for IDAC 0: IDAC on 1: IDAC off 0: IDAC on 1: IDAC off (9:8) MSB slice of 10 bit gain setting word for IDAC (7:0) LSB slice of 10 bit gain setting word for Aux DAC1 11111001 0 0 01 00000000 Rev. PrD | Page 17 of 34 AD9779 0D Auxiliary DAC1 Control and Data 7 6 5 1:0 0E QDAC Gain 0F QDAC Gain and Control 7:0 7 6 1:0 10 Auxiliary DAC2 Gain 11 Auxiliary DAC2 Control and Data 7:0 7 6 5 1:0 12 Cross Point Upper Delay 13 Cross Point Upper Delay 14 Wiggle Delay for Cross Point Control 15 Cross Point Control 7:0 Aux DAC1 Sign Aux DAC1 Direction Aux DAC1 Sleep Aux DAC1 Gain Adjustment QDAC Gain Adjustment QDAC Sleep QDAC Power Down QDAC Gain Adjustment Aux DAC2 Gain Adjustment Aux DAC2 Sign Aux DAC2 Direction Aux DAC2 Sleep Aux DAC2 Gain Adjustment Updelay Preliminary Technical Data 0: Positive 1: Negative 0: Source 1: Sink 0: Aux DAC1 on 1: Aux DAC 1 off (9:8) MSB slice of 10 bit gain setting word for Aux DAC1 (7:0) LSB slice of 10 bit gain setting word for QDAC 0: QDAC on 1: QDAC off 0: QDAC on 1: QDAC off (9:8) MSB slice of 10 bit gain setting word for QDAC (7:0) LSB slice of 10 bit gain setting word for Aux DAC2 0: Positive 1: Negative 0: Source 1: Sink 0: Aux DAC1 on 1: Aux DAC 1 off (9:8) MSB slice of 10 bit gain setting word for Aux DAC2 Value above zero for upper cross delay (bits 7,6, unused) 0 0 0 00 11111001 0 0 01 00000000 0 0 0 00 00000000 7:0 Dndelay Value below zero for lower cross delay (bits 7,6, unused) 00000000 7:3 2:0 7 6 5 4:2 1:0 7:0 7:6 2:0 Cross Control Clock Delay Wiggle Delay Cross Run Cross Status (read only) Cross Done (read only) Cross Wiggle Cross Step Analog Write Mirror Roll off Frequency Band Gap Trim Temperature Characteristic Divide rate of CNTCLK by 2^(3:0), CNTCLK = 1/16 DAC clock rate Time step in 2^(Wiggle Delay) CNTCLK cycles 0: Disables Cross Control loop 1: Enables Cross Control loop 0: Control loop is lowering cross point 1: Control loop is raising cross point 0: Control loop is chnaging cross point value 1: Control loop is holding cross point value (2:0) Number of iterations allowed in control loop (1:0) Value to change cross point value per iteration (wiggle) Provides extra writeable control registers for analog circuit 00000 000 0 0 0 000 00 00000000 00 000 16 Analog Write 17 Mirror Roll off and band gap Trim 18 Output Stack headroom Control 19 Analog Status 7:0 Analog Status Output stack headroom control Overdrive (current density) trim (temperature packing) Reference offset from VDD3V (vcas centering) Provides extra status register for analog circuitry (unused, read only) Rev. PrD | Page 18 of 34 Preliminary Technical Data 1A MISR Control 7 6 5 3 2:0 1B MISR Signature Register 1 1C MISR Signature Register 2 1D MISR Signature Register 3 1E MISR Signature Register 4 7:0 MISR Enable MISR IQ Select MISR Samples Internal Data Enable Test Mode MISR Signature 0: MISR disabled 1: MISR Enabled 0: Read back I path signature 1: Read back Q path signature 0: MISR uses short sample period 1: MISR uses long sample period 0: Internal data generator off 1: Internal data generator on 000: Normal data port operation 001-111: To be defined test modes (31:24) Slice of 32 bit MISR signature 0 0 0 0 AD9779 000 7:0 MISR Signature (23:16) Slice of 32 bit MISR signature 7:0 MISR Signature (15:8) Slice of 32 bit MISR signature 7:0 MISR Signature (7:0) Slice of 32 bit MISR signature Table 12: SPI RegisterDescription Rev. PrD | Page 19 of 34 AD9779 Interp. Factor 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 4 4 4 4 4 4 4 4 2 2 2 2 Filter Mode 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 00h 01h 02h 03h 04h 05h 06h 07h 00h 01h 02h 03h Filter1 mode (Mode_F1) Filter2 mode (Mode_F2) Filter3 mode (Mode_F3) Modulation Preliminary Technical Data Nyquist Zone Passband 1 2 3 4 5 6 7 8 -8 -7 -6 -5 -4 -3 -2 -1 1 2 3 4 -4 -3 -2 -1 1 2 -1 -2 F_low Center F_High (Freq. Normalized to FDAC) -0.05 0.0125 0.075 0.1375 0.2 0.2625 0.325 0.3875 0.45 0.5125 0.575 0.6375 0.7 0.7625 0.825 0.8875 -0.1 0.025 0.15 0.275 0.4 0.525 0.65 0.775 -0.2 0.05 0.3 0.55 0 0.0625 0.125 0.1875 0.25 0.3125 0.375 0.4375 0.5 0.5625 0.625 0.6875 0.75 0.8125 0.875 0.9375 0 0.125 0.25 0.375 0.5 0.625 0.75 0.875 0 0.25 0.5 0.75 0.05 0.1125 0.175 0.2375 0.3 0.3625 0.425 0.4875 0.55 0.6125 0.675 0.7375 0.8 0.8625 0.925 0.9875 0.1 0.225 0.35 0.475 0.6 0.725 0.85 0.975 0.2 0.45 0.7 0.95 BW=0.15-0.4 FDAC Worst case: F/8 In 2x Interpolation In 8x interpolation, BW=0.075-(0.2* FDAC) Worst case: F/16 In 8x interpolation, BW=0.0375(0.1* FDAC) Worst case: F/32 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 OFF OFF OFF OFF 0 0 1 2 2 2 3 4 4 4 5 6 6 6 7 0 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF DC_odd DC_even F/8_odd F/8_even 2F/8_odd 2F/8_even 3F/8_odd 3F/8_even -4F/8_even -4F/8_odd -3F/8_even -3F/8_odd -2F/8_even -2F/8_odd -F/8_even -F/8_odd DC_odd DC_even F/4_odd F/4_even -F/2_even -F/2_odd -F/4_even -F/4_odd DC_odd DC_even -F/2_even -F/2_odd Table 13: Interpolation Filter Modes, see Reg 01, bits 5 :2 Rev. PrD | Page 20 of 34 Preliminary Technical Data PLL Frequency Band Select PLL Band Select Value 11111 (31) 11110 (30) 11101 (29) 11100 (28) 11011 (27) 11010 (26) 11001 (25) 11000 (24) 10111 (23) 10110 (22) 10101 (21) 10100 (20) 10011 (19) 10010 (18) 10001 (17) 10000 (16) 01111 (15) 01110 (14) 01101 (13) 01100 (12) 01011 (11) 01010 (10) 01001 (9) 01000 (8) 00111 (7) Frequency in MHz 804 – 850 827 – 875 850 – 899 875 – 925 899 – 951 925 – 977 951 – 1005 977 – 1032 1004 – 1061 1032 – 1089 1060 – 1119 1089 – 1149 1118 – 1179 1148 – 1210 1176 – 1239 1206 – 1270 1237 – 1302 1268 – 1334 1299 – 1366 1331 – 1399 1363 – 1432 1396 – 1466 1425 – 1495 1458 – 1529 1492 – 1563 00110 (6) 00101 (5) 00100 (4) 00011 (3) 00010 (2) 00001 (1) 00000 (0) 1525 – 1597 1560 – 1632 1594 – 1667 1629 – 1702 1665 – 1737 1700 – 1773 1735 – 1810 AD9779 Table 14. VCO Frequency Range vs. PLL Band Select Value Rev. PrD | Page 21 of 34 AD9779 Internal Reference/Full Scale Current Generation Full scale current on the AD9779 IDAC and QDAC can be set from 10 to 30ma. Initially, the 1.2V bandgap reference is used to set up a current in an external resistor connected to I120 (pin 75). A simplified block diagram of the AD9779 reference circuitry is given below in Figure 29. The recommended value for the external resistor is 10K Ω, which sets up an I REFERENCE in the resistor of 120µa. Internal current mirrors provide a current gain scaling, where IDAC or QDAC gain is a 10 bit word in the SPI port register (registers 0A, 0B, 0E, and 0F). The default value for the DAC gain registers gives an IFS of 20ma. AD9779 IDAC gain 1.2V bandgap current scaling IDAC DAC full scale reference current QDAC QDAC gain 10KΩ Preliminary Technical Data Auxiliary DACs Two auxiliary DACs are provided on the AD9779. The full scale output current on these DACs is derived from the 1.2V bandgap reference and external resistor. The gain scale from the reference amplifier to the DAC reference current for each aux DAC is 16.67. with the Aux DAC gain set to full scale (10 bit values, SPI reg 0C, 0D, 10, 11), this gives a full scale current of 2ma for Aux DAC1 and for Aux DAC2. Through these same SPI port registers, the Aux DACs can be turned off, their signs can be inverted (scale is reversed, 0-1024 gives IFS to 0), and they can be programmed for sourcing or sinking current. When sourcing current, the output compliance voltage is 0-1.5V, and when sinking current the output compliance voltage is 0.8-1.5V. The Aux DACs can be used for LO cancellation when the DAC output is followed by a quadrature. A typical DAC to Quadrature Modulator interface is given in Figure 31. Often, the input common mode voltage for the modulator is much higher than the output compliance range of the DAC, so that ac coupling is necessary. The input referred offset voltage of thee quadrature modulator can result in LO feed through on the modulator output, degrading system, performance. If the configuration of Figure 29 is used, the Aux DACs can be used to compensate for the input DC offset of the quad mod, thus reducing LO feedthrough. AUX DAC1 VREF I120 0.1µF Figure 29 . Reference Circuitry where IFS is equal to; 1.2V ⎛ 27 ⎛ 6 ⎞⎞ ×⎜ ⎜ 12 + ⎜ 1024 × DAC gain ⎟ ⎟ × 32 ⎟ R ⎝ ⎠⎠ ⎝ 35 IOUT1_P 30 AUX1_P AUX1_N IDAC 25 IFS ( ma) 20 15 10 5 0 0 200 400 600 800 1000 DAC gain code IOUT1_N Quad Mod I Inputs IOUT2_P QDAC IOUT2_N AUX2_P Quad Mod Q Inputs AUX2_N AUX DAC2 Figure 30. IFS vs. DAC Gain Code Figure 31. Typical Use of Auxiliary DACs Power Down and Sleep Modes The AD9779 has a variety of power down modes, so that the digital engine, main TxDACs, or auxiliary DACs can be powered down individually, or all at once. Via the SPI port, the main TxDACs can be placed in sleep or powered down modes. In sleep mode, the TxDAC output is turned off, thus reducing power dissipation. The reference remains powered on though, so that recovery from sleep mode is very fast. When the TxDAC is placed in Power Down mode, the TxDAC and 1.2V bandgap reference are turned off. This mode offers more substantial power savings than in sleep mode, but the time to turn on is much longer. The Auxiliary DACs also have the capability to be programmed via the SPI port into sleep mode. Rev. PrD | Page 22 of 34 Preliminary Technical Data The power down bit (register 00h, bit 4) controls the power down function for the digital section of the AD9779. The power down function in bit 4 works in conjunction with TxEnable (pin 39) according to the following; TxEnable = 0:PWDWN= 0: Flush data path with zeroes 1: Digital engine in power down state, DACs and reference are not affected. 1: Normal operation 2. AD9779 PLL Disabled (reg 08h, bit 7=0) – The PLL enable switch in Figure 32 is connected to the Reference Clock Input. The differential reference clock input will be the DAC output sample rate and N3 will determine the interpolation rate. Internal PLL Clock Multiplier / Clock Distribution The internal clock structure on the AD9779 allows the user to drive the differential clock inputs with a clock at 1x or an integer multiple of the input data rate, or at the DAC output sample rate. A PLL internal to the AD9779 provides input clock multiplication and provides all of the internal clocks required for the interpolation filters and data synchronization. The internal clock architecture is shown in Figure 32. The reference clock is the differential clock at pins 5 and 6. This clock input can be run differentially, or singled ended by driving pin 5 with a clock signal, and biasing pin 6 to the mid swing point of the signal at pin 5. There are various configurations in which this clock architecture can be run; 1. PLL Enabled (reg 08h, bit 7=1) – The PLL enable switch in Figure 32 is connected to the junction of the dividers N1 and N2. Divider N3 determines the interpolation rate of the DAC, and the ratio N2/N3 determines the ratio of Reference Clock/Input Data Rate. The VCO runs optimally over the range 804MHz to 1800MHz, so that N1 is used to keep the speed of the VCO in this range, even though the DAC sample rate may be lower. The loop filter components are entirely internal and no external compensation is necessary. Figure 32. Internal Clock Architecture of AD9779 Timing Information Figure 33 through Figure 35 show some of the various timing possibilities when the PLL is enabled. The combination of the settings of N2 and N3 means that the reference clock frequency may be a multiple of the actual input data rate. Figure 33 through Figure 35 show, respectively, what the timing looks like when N2/N3 = 1, 2, and 4. Figure 36 shows the timing specifications for the AD9779 when the PLL is disabled. The reference clock is at the DAC output sample rate. In the example shown in Figure 36, if the PLL is disabled, the interpolation is 4x.. The set up and hold time for the input data are with respect to the rising edge of the reference clock which occurs just before the rising edge of the DATACLK out. Note that if reg 02h, bit2 is set, DATACLK out is inverted so the latching reference clock edge will occur just before the DATACLK out falling edge. Refe rence Clock tD DATA CLK out tS Input Data tH Figure 33. Timing Specifications for AD9779, PLL Enabled, Reference Clock = 1x Input Sample Rate Rev. PrD | Page 23 of 34 AD9779 Refe rence Clock tD DATA CLK out tS Input Data Preliminary Technical Data tH Figure 34. Timing Specifications for AD9779, PLL Enabled, Reference Clock = 2x Input Sample Rate Refe rence Clock tD DATA CLK out tS Input Data tH Figure 35. Timing Specifications for AD9779, PLL Enabled, Reference Clock = 4x Input Sample Rate Refe rence Clock tD DATA CLK out tS Input Data tS=-2.3ns typ tH=3.7ns typ tD=5.5ns typ tH Figure 36. Timing Specifications for AD9779, PLL Disabled, 4x Interpolation Using Data Delay to Meet Timing Requirements In order to meet strict timing requirements at input data rates of up to 250MSPS, the AD9779 has a fine timing feature. Fine timing adjustments can be made by programming values into the DATA CLOCK DELAY register (reg 03h, 5:3). By changing the values in this register, delay can be added to the default delay between the DACCLK in the DATACLK out. The effect of this is shown in Figure 37 and Figure 38. Figure 38. . Delay from DACCLK to DATACLK out with CLK DATA DELAY = 111 Figure 37. Delay from DACCLK to DATACLK out with CLK DATA DELAY = 000 The difference between the default delay of Figure 37 and the maximum delay shown in Figure 38 is the range programmable via the DATA CLK DELAY register. The resulting delays when programming DATA CLK DELAY between 000 and 111 are a linear extrapolation between these two figures. (typically 300ps400ps per increment to DATA CLK DELAY). Rev. PrD | Page 24 of 34 Preliminary Technical Data Interpolation Filter Architecture The AD9779 can provide up to 8× interpolation or disable the interpolation filters entirely. The coefficients of the low pass filters and the inverse sinc filter are given in Table 5, Table 6, Table 7, and Table 8. Spectral plots for the filter responses are given in Figure 3, Figure 4, and Figure 5. With the interpolation filter and modulator combined, the incoming signal can be placed anywhere within the Nyquist region of the DAC output sample rate. Where the input signal is complex, this architecture allows modulation of the input signal to positive or negative Nyquist regions (refer to Table 13). The Nyquist regions up to 4× the input data rate can be seen in Figure 39. 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -4 -3 -2 -1 0 1 2 AD9779 3 4 -8 -7 -6 -5 -4 -3 -2 -1 1 2 3 4 5 6 7 8 Figure 41. Interpolation/Modulation Combination of -3fDAC/8 Filter in Odd Mode -4× -3× -2× -1× DC 1× 2× 3× 4× 10 0 -10 Figure 39. Nyquist Zones Figure 3, Figure 4 and Figure 5 show the low pass response of the digital filters with no modulation used. By turning on the modulation feature, the response of the digital filters can be tuned to any Nyquist zone within the DAC bandwidth. As an example, Figure 40 to Figure 46 show the odd mode filter responses (refer to Table 13 for odd/even mode filter responses). -20 -30 -40 -50 -60 -70 -80 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -4 -3 -2 -1 0 1 2 3 4 -90 -100 -4 -3 -2 -1 0 1 2 3 4 Figure 42. Interpolation/Modulation Combination of -2fDAC/8 Filter in Odd Mode 10 0 -10 -20 -30 -40 -50 -60 Figure 40. Interpolation/Modulation Combination of -4fDAC/8 Filter in Odd Mode -70 -80 -90 -100 -4 -3 -2 -1 0 1 2 3 4 Figure 43. Interpolation/Modulation Combination of -1fDAC/8 Filter in Odd Mode Rev. PrD | Page 25 of 34 AD9779 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -4 -3 -2 -1 0 1 2 3 4 Preliminary Technical Data Even mode filter responses allow the passband to be centered around ±0.5, ±1.5, ±2.5 and ±3.5 FDATA. Switching from and odd mode response to an even mode filter response does not modulate the signal. Instead, the pass band is simply shifted. As an example, picture the response of Figure 46, and assume the signal in band is a complex signal over the bandwidth 3.2 to 3.3×FDATA. If the even mode filter response is then selected, the pass band will now be centered at 3.5×FDATA. However, the signal will still remain at the same place in the spectrum. The even/odd mode capability allows the passband to be placed anywhere in the DAC Nyquist bandwidth. The AD9779 is a dual DAC with an internal complex modulator built into the interpolating filter response. The modulator can be set to a real or a complex mode by programming register 02h, bit 5. In the default mode, bit 5 is set to zero and the modulation is complex. The AD9779 then expects the real and the imaginary components of a complex signal at digital input ports one and two (I and Q respectively). The DAC outputs will then represent the real and imaginary components of the input signal, modulated by the complex carrier FDAC/2, FDAC/4 or FDAC/8. With Bit 5 set to one, the modulation is real. The Q channel is shut off and it’s value at the modulator inputs replaced with zero. The output spectrum at either the IDAC or the QDAC will then represent the signal at digital input port one, real modulated by the internal digital carrier (FDAC/2, FDAC/4 or FDAC/8). Figure 44. Interpolation/Modulation Combination of fDAC/8 Filter in Odd Mode 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -4 -3 -2 -1 0 1 2 3 4 Figure 45. Interpolation/Modulation Combination of 2fDAC/8 Filter in Odd Mode 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -4 -3 -2 -1 0 1 2 3 4 Figure 46. Interpolation/Modulation Combination of 3fDAC/8 Filter in Odd Mode Rev. PrD | Page 26 of 34 Preliminary Technical Data EVALUATION BOARD SCHEMATICS AD9779 Figure 47. AD9779 Eval Board, Rev B , Power Supply Decoupling and SPI Interface Rev. PrD | Page 27 of 34 AD9779 Preliminary Technical Data Figure 48. AD9779 Eval Board, Rev B , Circuitry Local to AD9779 Rev. PrD | Page 28 of 34 Preliminary Technical Data AD9779 Figure 49. AD9779 Eval Board, RevB , AD8349 Quadrature Modulator Rev. PrD | Page 29 of 34 AD9779 Preliminary Technical Data Figure 50. AD9779 Eval Board, RevB , DAC Clock Interface Rev. PrD | Page 30 of 34 Preliminary Technical Data AD9779 Figure 51. AD9779 Eval Board, RevB , Input Port 1, Digital Input Buffers Rev. PrD | Page 31 of 34 AD9779 Preliminary Technical Data Figure 52. AD9779 Eval Board, RevB , Input Port 2, Digital Input Buffers Rev. PrD | Page 32 of 34 Preliminary Technical Data Outline Dimensions AD9779 Rev. PrD | Page 33 of 34 AD9779 ESD CAUTION Preliminary Technical Data ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. ORDERING GUIDE Model AD9779BSV AD9779/PCB Temperature Range -40°C to +85°C (Ambient) 25°C (Ambient) Description 100-Lead TQFP, Exposed Paddle Evaluation Board Table 15: Ordering Guide © 2005 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. PR05363–0–1/05(PrD) Rev. PrD | Page 34 of 34
AD9779PCB 价格&库存

很抱歉,暂时无法提供与“AD9779PCB”相匹配的价格&库存,您可以联系我们找货

免费人工找货